This allows you to specify the type of rgmii-id that will enable phy
internal delay in ethernet phy-mode.
This adds all RGMII cases to all of get_pinmode() except LD11, because LD11
SoC doesn't support RGMII due to the constraint of the hardware. When RGMII
phy mode is specified in the devicetree for LD11, the driver will abort
with an error.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix xdp_result initialization in netsec_process_rx in order to not
increase rx counters if there is no bpf program attached to the xdp hook
and napi_gro_receive returns GRO_DROP
Fixes: ba2b232108 ("net: netsec: add XDP support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix possible use-after-free in in netsec_process_rx that can occurs if
the first packet is sent to the normal networking stack and the
following one is dropped by the bpf program attached to the xdp hook.
Fix the issue defining the skb pointer in the 'budget' loop
Fixes: ba2b232108 ("net: netsec: add XDP support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first batch of driver conversions missed a few cases where we can
use phy_do_ioctl too.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building with PROVE_LOCKING=y, lockdep shows the following
dump message.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
...
Calling device_set_wakeup_enable() directly occurs this issue,
and it isn't necessary for initialization, so this patch creates
internal function __ave_ethtool_set_wol() and replaces with this
in ave_init() and ave_resume().
Fixes: 7200f2e3c9 ("net: ethernet: ave: Set initial wol state to disabled")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Socionext driver can run on dma coherent and non-coherent devices.
Get rid of huge dma_sync_single_for_device in netsec_alloc_rx_data since
now the driver can let page_pool API to managed needed DMA sync
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver only exists on a non NUMA aware machine.
With 44768decb7 ("page_pool: handle page recycle for NUMA_NO_NODE condition")
applied we can safely change that to NUMA_NO_NODE and accommodate future
NUMA aware hardware using netsec network interface
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change of_get_phy_mode() returned an enum,
phy_interface_t. On error, -ENODEV etc, is returned. If the result of
the function is stored in a variable of type phy_interface_t, and the
compiler has decided to represent this as an unsigned int, comparision
with -ENODEV etc, is a signed vs unsigned comparision.
Fix this problem by changing the API. Make the function return an
error, or 0 on success, and pass a pointer, of type phy_interface_t,
where the phy mode should be stored.
v2:
Return with *interface set to PHY_INTERFACE_MODE_NA on error.
Add error checks to all users of of_get_phy_mode()
Fixup a few reverse christmas tree errors
Fixup a few slightly malformed reverse christmas trees
v3:
Fix 0-day reported errors.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
bpf_xdp_adjust_head() can change the frame boundaries. Account for the
potential shift properly by calculating the new offset before
syncing the buffer to the device for XDP_TX
Fixes: ba2b232108 ("net: netsec: add XDP support")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increment netdev rx counters even for XDP_DROP verdict. Report even
tx bytes for xdp buffers (TYPE_NETSEC_XDP_TX or TYPE_NETSEC_XDP_NDO).
Moreover account pending buffer length in netsec_xdp_queue_one as it is
done for skb counterpart
Tested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always acquire tx descriptor spinlock even if a xdp program is not loaded
on the netsec device since ndo_xdp_xmit can run concurrently with
netsec_netdev_start_xmit and netsec_clean_tx_dring. This can happen
loading a xdp program on a different device (e.g virtio-net) and
xdp_do_redirect_map/xdp_do_redirect_slow can redirect to netsec even if
we do not have a xdp program on it.
Fixes: ba2b232108 ("net: netsec: add XDP support")
Tested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until calling register_netdev(), ndev->dev_name isn't specified, and
netdev_err() displays "(unnamed net_device)".
ave 65000000.ethernet (unnamed net_device) (uninitialized): invalid phy-mode setting
ave: probe of 65000000.ethernet failed with error -22
This replaces netdev_err() with dev_err() before calling register_netdev().
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "phy_mode" variable is an enum and in this context GCC treats it as
an unsigned int so the error handling is never triggered.
Fixes: 4c270b55a5 ("net: ethernet: socionext: add AVE ethernet driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "priv->phy_interface" variable is an enum and in this context GCC
will treat it as an unsigned int so the error handling is never
triggered.
Fixes: 533dd11a12 ("net: socionext: Add Synquacer NetSec driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: netdev@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On commit ba2b232108 ("net: netsec: add XDP support") a static
declaration for netsec_set_tx_de() was added to make the diff easier
to read. Now that the patch is merged let's move the functions around
and get rid of that
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While freeing tx buffers the memory has to be unmapped if the packet was
an skb or was used for .ndo_xdp_xmit using the same arguments. Get rid
of the unneeded extra 'else if' statement
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver starts using page_pool buffers before calling
xdp_rxq_info_reg_mem_model(). Start using the buffers after the
registration succeeded, so we won't have to call
page_pool_request_shutdown() in case of failure
Fixes: 5c67bf0ec4 ("net: netsec: Use page_pool API")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper recently removed page_pool_destroy() (from driver invocation)
and moved shutdown and free of page_pool into xdp_rxq_info_unreg(),
in-order to handle in-flight packets/pages. This created an asymmetry
in drivers create/destroy pairs.
This patch reintroduce page_pool_destroy and add page_pool user
refcnt. This serves the purpose to simplify drivers error handling as
driver now drivers always calls page_pool_destroy() and don't need to
track if xdp_rxq_info_reg_mem_model() was unsuccessful.
This could be used for a special cases where a single RX-queue (with a
single page_pool) provides packets for two net_device'es, and thus
needs to register the same page_pool twice with two xdp_rxq_info
structures.
This patch is primarily to ease API usage for drivers. The recently
merged netsec driver, actually have a bug in this area, which is
solved by this API change.
This patch is a modified version of Ivan Khoronzhuk's original patch.
Link: https://lore.kernel.org/netdev/20190625175948.24771-2-ivan.khoronzhuk@linaro.org/
Fixes: 5c67bf0ec4 ("net: netsec: Use page_pool API")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
cd1973a921 ("net: netsec: Sync dma for device on buffer allocation")
was merged on it's v1 instead of the v3.
Merge the proper patch version
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quoting Arnd,
We have to do a sync_single_for_device /somewhere/ before the
buffer is given to the device. On a non-cache-coherent machine with
a write-back cache, there may be dirty cache lines that get written back
after the device DMA's data into it (e.g. from a previous memset
from before the buffer got freed), so you absolutely need to flush any
dirty cache lines on it first.
Since the coherency is configurable in this device make sure we cover
all configurations by explicitly syncing the allocated buffer for the
device before refilling it's descriptors
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/socionext/netsec.c: In function 'netsec_clean_tx_dring':
drivers/net/ethernet/socionext/netsec.c:637:15: warning:
variable 'pkts' set but not used [-Wunused-but-set-variable]
It is not used since commit ba2b232108 ("net: netsec: add XDP support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interface only supports 1 Tx queue so locking is introduced on
the Tx queue if XDP is enabled to make sure .ndo_start_xmit and
.ndo_xdp_xmit won't corrupt Tx ring
- Performance (SMMU off)
Benchmark XDP_SKB XDP_DRV
xdp1 291kpps 344kpps
rxdrop 282kpps 342kpps
- Performance (SMMU on)
Benchmark XDP_SKB XDP_DRV
xdp1 167kpps 324kpps
rxdrop 164kpps 323kpps
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use page_pool and it's DMA mapping capabilities for Rx buffers instead
of netdev/napi_alloc_frag()
Although this will result in a slight performance penalty on small sized
packets (~10%) the use of the API will allow to easily add XDP support.
The penalty won't be visible in network testing i.e ipef/netperf etc, it
only happens during raw packet drops.
Furthermore we intend to add recycling capabilities on the API
in the future. Once the recycling is added the performance penalty will
go away.
The only 'real' penalty is the slightly increased memory usage, since we
now allocate a page per packet instead of the amount of bytes we need +
skb metadata (difference is roughly 2kb per packet).
With a minimum of 4BG of RAM on the only SoC that has this NIC the
extra memory usage is negligible (a bit more on 64K pages)
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netsec_process_rx was running in a loop trying to process as many packets
as possible before re-enabling interrupts. With the recent DMA changes
this is not needed anymore as we manage to consume all the budget without
looping over the function.
Since it has no performance penalty let's remove that and simplify the Rx
path a bit
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we changed the Tx ring handling and now depends on bit31 to figure
out the owner of the descriptor, we should initialize this every time
the device goes down-up instead of doing it once on driver init. If the
value is not correctly initialized the device won't have any available
descriptors
Changes since v1:
- Typo fixes
Fixes: 35e07d2347 ("net: socionext: remove mmio reads on Tx")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There was NVMEM support added to of_get_mac_address, so it could now
return ERR_PTR encoded error values, so we need to adjust all current
users of of_get_mac_address to this new fact.
While at it, remove superfluous is_valid_ether_addr as the MAC address
returned from of_get_mac_address is always valid and checked by
is_valid_ether_addr anyway.
Fixes: d01f449c00 ("of_net: add NVMEM support to of_get_mac_address")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netdev variant is usable on any context since it disables interrupts.
The napi variant of the call should only be used within softirq context.
Replace napi_alloc_frag on driver init with the correct netdev_alloc_frag
call
Changes since v1:
- Adjusted commit message
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Fixes: 4acb20b462 ("net: socionext: different approach on DMA")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Currently the driver issues 2 mmio reads to figure out the number of
transmitted packets and clean them. We can get rid of the expensive
reads since BIT 31 of the Tx descriptor can be used for that.
We can also remove the budget counting of Tx completions since all of
the descriptors are not deliberately processed.
Performance numbers using pktgen are:
size pre-patch(pps) post-patch(pps)
64 362483 427916
128 358315 411686
256 352725 389683
512 215675 216464
1024 113812 114442
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Running pktgen with packets sizes > 512b ends up in the interface Txq
getting stuck.
"netsec 522d0000.ethernet eth0: netsec_netdev_start_xmit: TxQFull!"
appears on dmesg but the interface never recovers. It requires an
ifconfig down/up to make the interface usable again.
The reason that triggers this, is a race condition between
.ndo_start_xmit and the napi completion. The available budget is
calculated first and indicates the queue is full. Due to a costly
netif_err() the queue is not stopped in time while the napi completion
runs, clears the irq and frees up descriptors, thus the queue never wakes
up again.
Fix this by moving the print after stopping the queue, make the print
ratelimited, add barriers and check for cleaned descriptors..
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts, seemingly all over the place.
I used Stephen Rothwell's sample resolutions for many of these, if not
just to double check my own work, so definitely the credit largely
goes to him.
The NFP conflict consisted of a bug fix (moving operations
past the rhashtable operation) while chaning the initial
argument in the function call in the moved code.
The net/dsa/master.c conflict had to do with a bug fix intermixing of
making dsa_master_set_mtu() static with the fixing of the tagging
attribute location.
cls_flower had a conflict because the dup reject fix from Or
overlapped with the addition of port range classifiction.
__set_phy_supported()'s conflict was relatively easy to resolve
because Andrew fixed it in both trees, so it was just a matter
of taking the net-next copy. Or at least I think it was :-)
Joe Stringer's fix to the handling of netns id 0 in bpf_sk_lookup()
intermixed with changes on how the sdif and caller_net are calculated
in these code paths in net-next.
The remaining BPF conflicts were largely about the addition of the
__bpf_md_ptr stuff in 'net' overlapping with adjustments and additions
to the relevant data structure where the MD pointer macros are used.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing MODULE_AUTHOR of ave driver and an entry to MAINTAINERS.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 26a4676faa ("arm64: mm: define NET_IP_ALIGN to 0"),
AVE controller affects this modification because the controller forces
to ignore lower 2bits of buffer start address, and make 2-byte headroom,
that is, data reception starts from (buffer + 2).
This patch defines AVE_FRAME_HEADROOM macro as hardware-specific value,
and replaces NET_IP_ALIGN with it.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To improve performance, this increases Rx descriptor to 256, Tx descriptor
to 64, and adjusts NAPI weight to NAPI_POLL_WEIGHT.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the wol state forces to be initialized after reset, the state should
be preserved in suspend/resume sequence.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If wol state of phy hardware is enabled after reset, phy_ethtool_get_wol()
returns that wol.wolopts is true.
However, since net_device.wol_enabled is zero and this doesn't apply wol
state until calling ethtool_set_wol(), so mdio_bus_phy_may_suspend()
returns true, that is, it's in a state where phy can suspend even though
wol state is enabled.
In this inconsistency, phy_suspend() returns -EBUSY, and at last,
suspend sequence fails with the following message:
dpm_run_callback(): mdio_bus_phy_suspend+0x0/0x58 returns -16
PM: Device 65000000.ethernet-ffffffff:01 failed to suspend: error -16
PM: Some devices failed to suspend, or early wake event detected
In order to fix the above issue, this patch forces to set initial wol state
to disabled as default.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces suspend and resume functions to ave driver.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few MAC/PHYs combinations which now support > 1Gbps. These
may need to make use of link modes with bits > 31. Thus their
supported PHY features or advertised features cannot be implemented
using the current bitmap in a u32. Convert to using a linkmode bitmap,
which can support all the currently devices link modes, and is future
proof as more modes are added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
return -ENOMEM directly instead of assigning it in a variable
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver dynamically allocates an skb and maps it as DMA Rx
buffer. In order to prepare for upcoming XDP changes, let's introduce a
different allocation scheme.
Buffers are allocated dynamically and mapped into hardware.
During the Rx operation the driver uses build_skb() to produce the
necessary buffers for the network stack.
This change increases performance ~15% on 64b packets with smmu disabled
and ~5% with smmu enabled
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We observed that packets and bytes count are not reset
when user performs interface down. Eventually, tx queue is
exhausted and packets will not be sent out.
To avoid this problem, resets tx queue in ndo_stop.
Fixes: 533dd11a12 ("net: socionext: Add Synquacer NetSec driver")
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Yoshitoyo Osaki <osaki.yoshitoyo@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a compatibility issue between RTL8211E implemented
in Developerbox and netsec ethernet controller IP.
Our MDIO controller stops MDC clock right after the write
access, but RTL8211E expects MDC clock must be kept toggling
for several clock cycle with MDIO high before entering
the IDLE state. Without keeping clock after write access,
write access is not correctly handled and register is not
updated.
To meet this requirement, netsec driver needs to issue dummy
read(e.g. read PHYID1(offset 0x2) register) right after write
access, to keep MDC clock.
We think this compatibility issue is a problem specific to
our MDIO controller and RTL8211E.
Fixes: 533dd11a12 ("net: socionext: Add Synquacer NetSec driver")
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Yoshitoyo Osaki <osaki.yoshitoyo@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ndo_stop, driver resets the netsec ethernet controller IP.
When the netsec IP is reset, HW running mode turns to NRM mode
and driver has to wait until this mode transition completes.
But mode transition to NRM will not complete if the PHY is
in normal operation state. Netsec IP requires PHY is in
power down state when it is reset.
This modification stops the PHY before resetting netsec.
Together with this modification, phy_addr is stored in netsec_priv
structure because ndev->phydev is not yet ready in ndo_init.
Fixes: 533dd11a12 ("net: socionext: Add Synquacer NetSec driver")
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Yoshitoyo Osaki <osaki.yoshitoyo@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were easy to resolve using immediate context mostly,
except the cls_u32.c one where I simply too the entire HEAD
chunk.
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 63ae7949e9 ("net: socionext: Use descriptor info instead of MMIO reads on Rx")
removed constant mmio reads from the driver and started using a descriptor
field to check if packet should be processed.
This lead the napi rx handler being constantly called while no packets
needed processing and ksoftirq getting 100% cpu usage. Issue one mmio read
to clear the irq correcty after processing packets
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to convert the local advertising to an LCL capabilities,
which is then used to resolve pause flow control settings.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kunihiko Hayashi