The IBSS code has a bogus mod_timer(..., 0) call,
we shouldn't ever pass a constant value to the
function since any constant value could be in the
future or the past.
However, invoking the timer here is not necessary
at all, since we just finished scanning and just
need to have the IBSS code run again from the
workqueue later, so factor out the work starting
and use that instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, when one interface switches HT mode,
all others will follow along. This is clearly
undesirable, since the new one might switch to
no-HT while another one is operating in HT.
Address this issue by keeping track of the HT
mode per interface, and allowing only changes
that are compatible, i.e. switching into HT40+
is not possible when another interface is in
HT40-, in that case the second one needs to
fall back to HT20.
Also, to allow drivers to know what's going on,
store the per-interface HT mode (channel type)
in the virtual interface's bss_conf.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"mac80211: improve IBSS scanning" was missing a hunk.
This adds that hunk as originally intended.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When IBSS is fixed to a frequency, it can still
scan to try to find the right BSSID. This makes
sense if the BSSID isn't also fixed, but it need
not scan all channels -- just one is sufficient.
Make it do that by moving the scan setup code to
ieee80211_request_internal_scan() and include
a channel variable setting.
Note that this can be further improved to start
the IBSS right away if both frequency and BSSID
are fixed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My previous patch "mac80211: notify driver about
IBSS status" left a problem -- when we merge with
a new BSSID, we never tell the driver that we left
the old one. Fix that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some drivers (e.g. iwlwifi) need to know and try
to figure it out based on other things, but making
it explicit is definitely better.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
when an IBSS merge happened, the supported rates for the newly added station
were left empty, causing the rate control module to be initialized with only
the basic rates.
the section of the ibss code which deals with updating supported rates for
an already existing station failed to inform the rate control module about the
new rates. as both minstrel and pid don't have an update function i just use
the init function.
also remove unnecessary (unsigned long long) casts and edit debug message.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
when an IBSS merge happened, the supported rates for the newly added station
were left empty, causing the rate control module to be initialized with only
the basic rates.
also the section of the ibss code which deals with updating supported rates for
an already existing station fails to inform the rate control module about the
new rates. as i don't know how to fix this (minstrel does not have an update
function), i have just added a comment for now.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Many drivers would like to sleep during station
addition and removal, and currently have a high
complexity there from not being able to.
This introduces two new callbacks sta_add() and
sta_remove() that drivers can implement instead
of using sta_notify() and that can sleep, and
the new sta_add() callback is also allowed to
fail.
The reason we didn't do this previously is that
the IBSS code wants to insert stations from the
RX path, which is a tasklet, so cannot sleep.
This patch will keep the station allocation in
that path, but moves adding the station to the
driver out of line. Since the addition can now
fail, we can have IBSS peer structs the driver
rejected -- in that case we still talk to the
station but never tell the driver about it in
the control.sta pointer. If there will ever be
a driver that has a low limit on the number of
stations and that cannot talk to any stations
that are not known to it, we need to do come up
with a new strategy of handling larger IBSSs,
maybe quicker expiry or rejecting peers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We only reply to probe request if either the requested SSID is the
broadcast SSID or if the requested SSID matches our own SSID. This
latter case was not properly handled since we were replying to different
SSID with the same length as our own SSID.
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
First, both beacons and probe responses can be used for IBSS merge.
Next, sdata->u.ibss.bssid was always true (and thus IBSS merge was
disabled). We should use sdata->u.ibss.fixed_bssid instead.
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee82011_sta_find_ibss() and ieee80211_sta_merge_ibss() are always
called with a defined state. So it's useless to check it or set it in
those function.
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211 offers private data for each BSS struct,
which mac80211 uses. However, mac80211 uses internal
and external (cfg80211) BSS pointers interchangeably
and has a hack to put the cfg80211 bss struct into
the private struct.
Remove this hack, properly converting between the
pointers wherever necessary.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of always using netif_running(sdata->dev)
use ieee80211_sdata_running(sdata) now which is
just an inline containing netif_running() for now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When fixed bssid is requested when joining an ibss network, incoming
beacons that match the configured bssid cause mac80211 to create new
sta entries, even before the ibss interface is in joined state.
When that happens, it fails to bring up the interface entirely, because
it checks for existing sta entries before joining.
This patch fixes this bug by refusing to create sta info entries before
the interface is fully operational.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For bluetooth 3, we will most likely not have
a netdev for a virtual interface (sdata), so
prepare for that by reducing the reliance on
having a netdev. This patch moves the name
and address fields into the sdata struct and
uses them from there all over. Some work is
needed to keep them sync'ed, but that's not
a lot of work and in slow paths anyway.
In doing so, this also reduces the number of
pointer dereferences in many places, because
of things like sdata->dev->dev_addr becoming
sdata->vif.addr.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The station management currently uses the virtual
interface, but you cannot add the same station to
multiple virtual interfaces if you're communicating
with it in multiple ways.
This restriction should be lifted so that in the
future we can, for instance, support bluetooth 3
with an access point that mac80211 is already
associated to.
We can do that by requiring all sta_info_get users
to provide the virtual interface and making the RX
code aware that an address may match more than one
station struct. Thanks to the previous patches this
one isn't all that large and except for the RX and
TX status paths changes has low complexity.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the flags moved into skb->cb, there's no
longer a need to have the encrypt bool passed
into the function, anyone who requires it set
to 0 (false) can just set the flag directly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, in IBSS mode, a single creator would go into
a loop trying to merge/scan. This happens because the IBSS timer is
rearmed on finishing a scan and the subsequent
timer invocation requests another scan immediately.
This patch fixes this issue by checking if we have just completed
a scan run trying to merge with other IBSS networks.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The IBSS code leaks a BSS struct after telling
cfg80211 about a given BSS by passing a frame.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent commit "mac80211: fix logic error ibss merge bssid check" fixed
joining of ibss cell when static bssid is provided. In this case
ifibss->bssid is set before the cell is joined and comparing that address
to a bss should thus always succeed. Unfortunately this change broke the
other case of joining a ibss cell without providing a static bssid where
the value of ifibss->bssid is not set before the cell is joined.
Since ifibss->bssid may be set before or after joining the cell we do not
learn anything by comparing it to a known bss. Remove this check.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a scan completes, we call ieee80211_sta_find_ibss(),
which is also called from other places. When the scan was
done in software, there's no problem as both run from the
single-threaded mac80211 workqueue and are thus serialised
against each other, but with hardware scan the completion
can be in a different context and race against callers of
this function from the workqueue (e.g. due to beacon RX).
So instead of calling ieee80211_sta_find_ibss() directly,
just arm the timer and have it fire, scheduling the work,
which will invoke ieee80211_sta_find_ibss() (if that is
appropriate in the current state).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mac80211 workqueue exists to enable mac80211 and drivers
to queue their own work on a single threaded workqueue. mac80211
takes care to flush the workqueue during suspend but we never
really had requirements on drivers for how they should use
the workqueue in consideration for suspend.
We extend mac80211 to document how the mac80211 workqueue should
be used, how it should not be used and finally move raw access to
the workqueue to mac80211 only. Drivers and mac80211 use helpers
to queue work onto the mac80211 workqueue:
* ieee80211_queue_work()
* ieee80211_queue_delayed_work()
These helpers will now warn if mac80211 already completed its
suspend cycle and someone is trying to queue work. mac80211
flushes the mac80211 workqueue prior to suspend a few times,
but we haven't taken the care to ensure drivers won't add more
work after suspend. To help with this we add a warning when
someone tries to add work and mac80211 already completed the
suspend cycle.
Drivers should ensure they cancel any work or delayed work
in the mac80211 stop() callback.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a bitfield to store the current scan mode instead of two boolean
variables {sw,hw}_scanning. This patch does not introduce functional
changes but allows us to enhance the scan flags later (for example
for background scanning).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reworks the key operation in cfg80211, and now only
allows, from userspace, configuring keys (via nl80211)
after the connection has been established (in managed
mode), the IBSS been joined (in IBSS mode), at any time
(in AP[_VLAN] modes) or never for all the other modes.
In order to do shared key authentication correctly, it
is now possible to give a WEP key to the AUTH command.
To configure static WEP keys, these are given to the
CONNECT or IBSS_JOIN command directly, for a userspace
SME it is assumed it will configure it properly after
the connection has been established.
Since mac80211 used to check the default key in IBSS
mode to see whether or not the network is protected,
it needs an update in that area, as well as an update
to make use of the WEP key passed to auth() for shared
key authentication.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Within mac80211, we often need to copy the rx status into
skb->cb. This is wasteful, as drivers could be building it
in there to start with. This patch changes the API so that
drivers are expected to pass the RX status in skb->cb, now
accessible as IEEE80211_SKB_RXCB(skb). It also updates all
drivers to pass the rx status in there, but only by making
them memcpy() it into place before the call to the receive
function (ieee80211_rx(_irqsafe)). Each driver can now be
optimised on its own schedule.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I fixed the crypto bit I must have done the negative
test only -- it is quite clearly impossible to find _any_
IBSS to join with the parameters put the wrong way around.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We forgot to cancel all timers in mac80211 when suspending.
In particular we forgot to deal with some things that can
cause hardware reconfiguration -- while it is down.
While at it we go ahead and add a warning in ieee80211_sta_work()
if its run while the suspend->resume cycle is in effect. This
should not happen and if it does it would indicate there is
a bug lurking in either mac80211 or mac80211 drivers.
With this now wpa_supplicant doesn't blink when I go to suspend
and resume where as before there where issues with some timers
running during the suspend->resume cycle. This caused a lot of
incorrect assumptions and would at times bring back the device
in an incoherent, but mostly recoverable, state.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently mac80211 announces a rate set with no basic rates,
this fixes it to use 1/2 or 6/9 Mbit as basic rates by default.
Additionally, mac80211 will currently adopt the peer's entire
rate set, rather than just the basic rate set; fix that too.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even when we find an IBSS with the SSID we're looking for, we
may not be able to connect to it because it has a key and we
don't, or vice versa. Avoid such situations by checking the
privacy capability bit.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we aren't doing anything in mac80211, we can turn off
much of the hardware, depending on the driver/hw. Not doing
anything, aka being idle, means:
* no monitor interfaces
* no AP/mesh/wds interfaces
* any station interfaces are in DISABLED state
* any IBSS interfaces aren't trying to be in a network
* we aren't trying to scan
By creating a new function that verifies these conditions and calling
it at strategic points where the states of those conditions change,
we can easily make mac80211 tell the driver when we are idle to save
power.
Additionally, this fixes a small quirk where a recalculated powersave
state is passed to the driver even if the hardware is about to stopped
completely.
This patch intentionally doesn't touch radio_enabled because that is
currently implemented to be a soft rfkill which is inappropriate here
when we need to be able to wake up with low latency.
One thing I'm not entirely sure about is this:
phy0: device no longer idle - in use
wlan0: direct probe to AP 00:11:24:91:07:4d try 1
wlan0 direct probe responded
wlan0: authenticate with AP 00:11:24:91:07:4d
wlan0: authenticated
> phy0: device now idle
> phy0: device no longer idle - in use
wlan0: associate with AP 00:11:24:91:07:4d
wlan0: RX AssocResp from 00:11:24:91:07:4d (capab=0x401 status=0 aid=1)
wlan0: associated
Is it appropriate to go into idle state for a short time when we have
just authenticated, but not associated yet? This happens only with the
userspace SME, because we cannot really know how long it will wait
before asking us to associate. Would going idle after a short timeout
be more appropriate? We may need to revisit this, depending on what
happens.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to later add tracing or verifications to the driver
calls mac80211 makes, this patch adds static inline wrappers
for all operations.
All calls are now written as
drv_<op>(local, ...);
instead of
local->ops-><op>(&local->hw, ...);
Where necessary, the wrappers also do existence checking and
return default values as appropriate.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The config_interface method is a little strange, it contains the
BSSID and beacon updates, while bss_info_changed contains most
other BSS information for each interface. This patch removes
config_interface and rolls all the information it previously
passed to drivers into bss_info_changed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We currently have two beacon interval configuration knobs:
hw.conf.beacon_int and vif.bss_info.beacon_int. This is
rather confusing, even though the former is used when we
beacon ourselves and the latter when we are associated to
an AP.
This just deprecates the hw.conf.beacon_int setting in favour
of always using vif.bss_info.beacon_int. Since it touches all
the beaconing IBSS code anyway, we can also add support for
the cfg80211 IBSS beacon interval configuration easily.
NOTE: The hw.conf.beacon_int setting is retained for now due
to drivers still using it -- I couldn't untangle all
drivers, some are updated in this patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are some places marked
/* XXX maybe racy? */
and they really are racy because there's no locking.
This patch reworks much of the scan code, and introduces proper
locking for the scan request as well as the internal scanning
(which is necessary for IBSS/managed modes). Helper functions
are added to call the scanning code whenever necessary. The
scan deferring is changed to simply queue the scanning work
instead of trying to start the scan in place, the scanning work
will then take care of the rest.
Also, currently when internal scans are requested for an interface
that is trying to associate, we reject such scans. This was not
intended, the mlme code has provisions to scan twice when it can't
find the BSS to associate with right away; this has never worked
properly. Fix this by not rejecting internal scan requests for an
interface that is associating.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the IBSS code wants to scan, but that fails, we can
get stuck in a situation where you can never scan again.
Fix this by properly notifying ourselves when the scan
request has failed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are a few problems in the IBSS code:
a) it tries to activate interfaces that are down after scanning
b) it crashes after scanning on an IBSS iface that isn't active
c) since the ssid_len is used as a flag, need to make it visible
only after all other settings are set, this helps protect
against b)
For b), we get a system crash:
wlan0: Creating new IBSS network, BSSID ce:f9:88:76:1e:4d
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<...>] ieee80211_sta_find_ibss+0x294/0x37d [mac80211]
Call Trace:
[<...>] ieee80211_ibss_notify_scan_completed+0x0/0x88 [mac80211]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the RCU locking here we sleep while in an atomic context,
since we can sleep just use mutex locking for the interface
list instead of RCU. Sorry, seems I didn't get that in my UML
test.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This converts mac80211 to the new cfg80211 IBSS API, the
wext handling functions are called where appropriate.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't call ieee80211_sta_find_ibss() directly, like it's done in STA
mode, so that the commit() call is more harmless respectively has
less site-effects.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In IBSS mode, the beacon timestamp has to be filled with the
BSS's timestamp when joining, and set to zero when creating
a new BSS.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Give slow hardware some time to do the TSF sync, to not run into an
IBSS merging endless loop in some rarely situations.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It was not a good idea to do a TSF reset on strange IBSS merges to the same BSSID. For example it will break the TSF sync of ath9k completely and it is unnecessary as all hardware I have tested do a TSF sync to a higher value automatically and IBSS merges are only done to higher TSF values. It only need a TSF reset to accept a lower value, when the IBSS network is changed manually.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces a generic commit() function which initiate a
new network joining process. It should be called after some interface
config changes, so that the changes get applied more cleanly. Currently
set_ssid() and set_bssid() call it. Others can be added in future
patches.
In version 1 the header files was forgotten, sorry.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch splits out the ibss code and data from managed (station) mode.
The reason to do this is to better separate the state machines, and have
the code be contained better so it gets easier to determine what exactly
a given change will affect, that in turn makes it easier to understand.
This is quite some churn, especially because I split sdata->u.sta into
sdata->u.mgd and sdata->u.ibss, but I think it's easier to maintain that
way. I've also shuffled around some code -- null function sending is only
applicable to managed interfaces so put that into that file, some other
functions are needed from various places so put them into util, and also
rearranged the prototypes in ieee80211_i.h accordingly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg