Devices which do not support PCI configuration space based power
management may not otherwise be enabled.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The following patch sets the MaxPayload setting to match the parent
reading when inserting a PCIE card into a hotplug slot. On our system,
the upstream bridge is set to 256, but when inserting a card, the card
setting defaults to 128. As soon as I/O is performed to the card it
starts receiving errors since the payload size is too small.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jordan Hargrave <jordan_hargrave@dell.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If a device doesn't support power management (pm_cap == 0) but it is
acpi_pci_power_manageable() because there is a _PS0 method declared for
it and _EJ0 is also declared for the slot then nobody is going to set
current_state = PCI_D0 for this device. This is what I think it is
happening:
pci_enable_device
|
__pci_enable_device_flags
/* here we do not set current_state because !pm_cap */
|
do_pci_enable_device
|
pci_set_power_state
|
__pci_start_power_transition
|
pci_platform_power_transition
/* platform_pci_power_manageable() calls acpi_pci_power_manageable that
* returns true */
|
platform_pci_set_power_state
/* acpi_pci_set_power_state gets called and does nothing because the
* acpi device has _EJ0, see the comment "If the ACPI device has _EJ0,
* ignore the device" */
at this point if we refer to the commit message that introduced the
comment above (10b3dcae0f), it is up to
the hotplug driver to set the state to D0.
However AFAICT the pci hotplug driver never does, in fact
drivers/pci/hotplug/acpiphp_glue.c:register_slot sets the slot flags to
(SLOT_ENABLED | SLOT_POWEREDON) but it does not set the pci device
current state to PCI_D0.
So my proposed fix is also to set current_state = PCI_D0 in
register_slot.
Comments are very welcome.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Remove kobject.h from files which don't need it, notably,
sched.h and fs.h.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If pcie_ports_disabled is set, pcie_port_service_register() returns
error code and select_detection_mode() should not attempt to
unregister dummy_driver and use dummy_slots. It should return
PCIEHP_DETECT_ACPI immediately instead.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
While testing various randconfigs with ktest.pl, I hit the following panic:
BUG: unable to handle kernel paging request at f7e54b03
IP: [<c0d63409>] ibmphp_access_ebda+0x101/0x19bb
Adding printks, I found that the loop that reads the ebda blocks
can move out of the mapped section.
ibmphp_access_ebda: start=f7e44c00 size=5120 end=f7e46000
ibmphp_access_ebda: io_mem=f7e44d80 offset=384
ibmphp_access_ebda: io_mem=f7e54b03 offset=65283
The start of the iomap was at f7e44c00 and had a size of 5120,
making the end f7e46000. We start with an offset of 0x180 or
384, giving the first read at 0xf7e44d80. Reading that location
yields 65283, which is much bigger than the 5120 that was allocated
and makes the next read at f7e54b03 which is outside the mapped area.
Perhaps this is a bug in the driver, or buggy hardware, but this patch
is more about not crashing my box on start up and just giving a warning
if it detects this error.
This patch at least lets my box boot with just a warning.
Cc: Chandru Siddalingappa <chandru@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (27 commits)
x86: allocate space within a region top-down
x86: update iomem_resource end based on CPU physical address capabilities
x86/PCI: allocate space from the end of a region, not the beginning
PCI: allocate bus resources from the top down
resources: support allocating space within a region from the top down
resources: handle overflow when aligning start of available area
resources: ensure callback doesn't allocate outside available space
resources: factor out resource_clip() to simplify find_resource()
resources: add a default alignf to simplify find_resource()
x86/PCI: MMCONFIG: fix region end calculation
PCI: Add support for polling PME state on suspended legacy PCI devices
PCI: Export some PCI PM functionality
PCI: fix message typo
PCI: log vendor/device ID always
PCI: update Intel chipset names and defines
PCI: use new ccflags variable in Makefile
PCI: add PCI_MSIX_TABLE/PBA defines
PCI: add PCI vendor id for STmicroelectronics
x86/PCI: irq and pci_ids patch for Intel Patsburg DeviceIDs
PCI: OLPC: Only enable PCI configuration type override on XO-1
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: remove in_workqueue_context()
workqueue: Clarify that schedule_on_each_cpu is synchronous
memory_hotplug: drop spurious calls to flush_scheduled_work()
shpchp: update workqueue usage
pciehp: update workqueue usage
isdn/eicon: don't call flush_scheduled_work() from diva_os_remove_soft_isr()
workqueue: add and use WQ_MEM_RECLAIM flag
workqueue: fix HIGHPRI handling in keep_working()
workqueue: add queue_work and activate_work trace points
workqueue: prepare for more tracepoints
workqueue: implement flush[_delayed]_work_sync()
workqueue: factor out start_flush_work()
workqueue: cleanup flush/cancel functions
workqueue: implement alloc_ordered_workqueue()
Fix up trivial conflict in fs/gfs2/main.c as per Tejun
* Rename shpchp_wq to shpchp_ordered_wq and add non-ordered shpchp_wq
which is used instead of the system workqueue. This is to remove
the use of flush_scheduled_work() which is deprecated and scheduled
for removal.
* With cmwq in place, there's no point in creating workqueues lazily.
Create both shpchp_wq and shpchp_ordered_wq upfront.
* Include workqueue.h from shpchp.h.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* Rename pciehp_wq to pciehp_ordered_wq and add non-ordered pciehp_wq
which is used instead of the system workqueue. This is to remove
the use of flush_scheduled_work() which is deprecated and scheduled
for removal.
* With cmwq in place, there's no point in creating workqueues lazily.
Create both pciehp_wq and pciehp_ordered_wq upfront.
* Include workqueue.h from pciehp.h.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Get rid of init_MUTEX[_LOCKED]() and use sema_init() instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
All these files use the big kernel lock in a trivial
way to serialize their private file operations,
typically resulting from an earlier semi-automatic
pushdown from VFS.
None of these drivers appears to want to lock against
other code, and they all use the BKL as the top-level
lock in their file operations, meaning that there
is no lock-order inversion problem.
Consequently, we can remove the BKL completely,
replacing it with a per-file mutex in every case.
Using a scripted approach means we can avoid
typos.
These drivers do not seem to be under active
maintainance from my brief investigation. Apologies
to those maintainers that I have missed.
file=$1
name=$2
if grep -q lock_kernel ${file} ; then
if grep -q 'include.*linux.mutex.h' ${file} ; then
sed -i '/include.*<linux\/smp_lock.h>/d' ${file}
else
sed -i 's/include.*<linux\/smp_lock.h>.*$/include <linux\/mutex.h>/g' ${file}
fi
sed -i ${file} \
-e "/^#include.*linux.mutex.h/,$ {
1,/^\(static\|int\|long\)/ {
/^\(static\|int\|long\)/istatic DEFINE_MUTEX(${name}_mutex);
} }" \
-e "s/\(un\)*lock_kernel\>[ ]*()/mutex_\1lock(\&${name}_mutex)/g" \
-e '/[ ]*cycle_kernel_lock();/d'
else
sed -i -e '/include.*\<smp_lock.h\>/d' ${file} \
-e '/cycle_kernel_lock()/d'
fi
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
One of the recent changes caused complilation of
drivers/pci/hotplug/pciehp_core.c to fail. Fix this issue.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
After commit 852972acff (ACPI: Disable
ASPM if the platform won't provide _OSC control for PCIe) control of
the PCIe Capability Structure is unconditionally requested by
acpi_pci_root_add(), which in principle may cause problems to
happen in two ways. First, the BIOS may refuse to give control of
the PCIe Capability Structure if it is not asked for any of the
_OSC features depending on it at the same time. Second, the BIOS may
assume that control of the _OSC features depending on the PCIe
Capability Structure will be requested in the future and may behave
incorrectly if that doesn't happen. For this reason, control of
the PCIe Capability Structure should always be requested along with
control of any other _OSC features that may depend on it (ie. PCIe
native PME, PCIe native hot-plug, PCIe AER).
Rework the PCIe port driver so that (1) it checks which native PCIe
port services can be enabled, according to the BIOS, and (2) it
requests control of all these services simultaneously. In
particular, this causes pcie_portdrv_probe() to fail if the BIOS
refuses to grant control of the PCIe Capability Structure, which
means that no native PCIe port services can be enabled for the PCIe
Root Complex the given port belongs to. If that happens, ASPM is
disabled to avoid problems with mishandling it by the part of the
PCIe hierarchy for which control of the PCIe Capability Structure
has not been received.
Make it possible to override this behavior using 'pcie_ports=native'
(use the PCIe native services regardless of the BIOS response to the
control request), or 'pcie_ports=compat' (do not use the PCIe native
services at all).
Accordingly, rework the existing PCIe port service drivers so that
they don't request control of the services directly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
It is possible that the BIOS will not grant control of all _OSC
features requested via acpi_pci_osc_control_set(), so it is
recommended to negotiate the final set of _OSC features with the
query flag set before calling _OSC to request control of these
features.
To implement it, rework acpi_pci_osc_control_set() so that the caller
can specify the mask of _OSC control bits to negotiate and the mask
of _OSC control bits that are absolutely necessary to it. Then,
acpi_pci_osc_control_set() will run _OSC queries in a loop until
the mask of _OSC control bits returned by the BIOS is equal to the
mask passed to it. Also, before running the _OSC request
acpi_pci_osc_control_set() will check if the caller's required
control bits are present in the final mask.
Using this mechanism we will be able to avoid situations in which the
BIOS doesn't grant control of certain _OSC features, because they
depend on some other _OSC features that have not been requested.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Removed check to prevent hotplug of display devices within shpchp.
Originally this was thought to have been required within the PCI
Hotplug specification for some legacy devices. However there is
no such requirement in the most recent revision. The check prevents
hotplug of not only display devices but also computational GPUs
which require serviceability.
Signed-off-by: Praveen Kalamegham <praveen@nextio.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The SLOT_REG_RSVDZ_MASK macro is normally used like this:
slot_reg &= ~SLOT_REG_RSVDZ_MASK;
The ~ operator has higher precedence than the | operator from inside the
macro, so it needs parenthesis.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There are devices out there which are PCI Hot-plug controllers with
compaq PCI IDs, but are not bridges, hence have pdev->subordinate
NULL. But cpqphp expects the pointer to be non-NULL.
Add a check to the probe function to avoid oopses like:
BUG: unable to handle kernel NULL pointer dereference at 00000050
IP: [<f82e3c41>] cpqhpc_probe+0x951/0x1120 [cpqphp]
*pdpt = 0000000033779001 *pde = 0000000000000000
...
The device here was:
00:0b.0 PCI Hot-plug controller [0804]: Compaq Computer Corporation PCI Hotplug Controller [0e11:a0f7] (rev 11)
Subsystem: Compaq Computer Corporation Device [0e11:a2f8]
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Removed check to prevent hotplug of display devices within pciehp.
Originally this was thought to have been required within the PCI
Hotplug specification for some legacy devices. However there is
no such requirement in the most recent revision. The check prevents
hotplug of not only display devices but also computational GPUs
which require serviceability.
Signed-off-by: Praveen Kalamegham <praveen@nextio.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This allows bin_attr->read,write,mmap callbacks to check file specific data
(such as inode owner) as part of any privilege validation.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (44 commits)
vlynq: make whole Kconfig-menu dependant on architecture
add descriptive comment for TIF_MEMDIE task flag declaration.
EEPROM: max6875: Header file cleanup
EEPROM: 93cx6: Header file cleanup
EEPROM: Header file cleanup
agp: use NULL instead of 0 when pointer is needed
rtc-v3020: make bitfield unsigned
PCI: make bitfield unsigned
jbd2: use NULL instead of 0 when pointer is needed
cciss: fix shadows sparse warning
doc: inode uses a mutex instead of a semaphore.
uml: i386: Avoid redefinition of NR_syscalls
fix "seperate" typos in comments
cocbalt_lcdfb: correct sections
doc: Change urls for sparse
Powerpc: wii: Fix typo in comment
i2o: cleanup some exit paths
Documentation/: it's -> its where appropriate
UML: Fix compiler warning due to missing task_struct declaration
UML: add kernel.h include to signal.c
...
Use kmemdup when some other buffer is immediately copied into the
allocated region.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
statement S;
@@
- to = \(kmalloc\|kzalloc\)(size,flag);
+ to = kmemdup(from,size,flag);
if (to==NULL || ...) S
- memcpy(to, from, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This ensures that the translations for unmapped IO mappings or
unmapped memory are properly removed from the MMU hash table
before such an unplug. Without this, the hypervisor refuses the
unplug operations due to those resources still being mapped by
the partition.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
No functional change; just print resources in the conventional style.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Per ACPI spec, _ERG method should be executed before device driver
gets control for hotpluged device. Firmware might do some configuration
there. See http://bugzilla.kernel.org/show_bug.cgi?id=10805. In this
machine, _REG method of docked device will configure cardbus bridge.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Tested-by: Paul Martin <pm@debian.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Constify struct sysfs_ops.
This is part of the ops structure constification
effort started by Arjan van de Ven et al.
Benefits of this constification:
* prevents modification of data that is shared
(referenced) by many other structure instances
at runtime
* detects/prevents accidental (but not intentional)
modification attempts on archs that enforce
read-only kernel data at runtime
* potentially better optimized code as the compiler
can assume that the const data cannot be changed
* the compiler/linker move const data into .rodata
and therefore exclude them from false sharing
Signed-off-by: Emese Revfy <re.emese@gmail.com>
Acked-by: David Teigland <teigland@redhat.com>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'x86-bootmem-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (30 commits)
early_res: Need to save the allocation name in drop_range_partial()
sparsemem: Fix compilation on PowerPC
early_res: Add free_early_partial()
x86: Fix non-bootmem compilation on PowerPC
core: Move early_res from arch/x86 to kernel/
x86: Add find_fw_memmap_area
Move round_up/down to kernel.h
x86: Make 32bit support NO_BOOTMEM
early_res: Enhance check_and_double_early_res
x86: Move back find_e820_area to e820.c
x86: Add find_early_area_size
x86: Separate early_res related code from e820.c
x86: Move bios page reserve early to head32/64.c
sparsemem: Put mem map for one node together.
sparsemem: Put usemap for one node together
x86: Make 64 bit use early_res instead of bootmem before slab
x86: Only call dma32_reserve_bootmem 64bit !CONFIG_NUMA
x86: Make early_node_mem get mem > 4 GB if possible
x86: Dynamically increase early_res array size
x86: Introduce max_early_res and early_res_count
...
No functional change; this converts loops that iterate from 0 to
PCI_BUS_NUM_RESOURCES through pci_bus resource[] table to use the
pci_bus_for_each_resource() iterator instead.
This doesn't change the way resources are stored; it merely removes
dependencies on the fact that they're in a table.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Move bus_size_bridges and assign resources out of pciehp_add_bridge()
and do them all together, one time, including slot bridge, to avoid to
calling assign resources several times when there are several bridges
under the slot bridge. Using pci_assign_unassigned_bridge_resources.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add header file to fix build error:
drivers/pci/hotplug/ibmphp_hpc.c:135: error: implicit declaration of function 'init_MUTEX'
drivers/pci/hotplug/ibmphp_hpc.c:136: error: implicit declaration of function 'init_MUTEX_LOCKED'
drivers/pci/hotplug/ibmphp_hpc.c:797: error: implicit declaration of function 'down'
drivers/pci/hotplug/ibmphp_hpc.c:807: error: implicit declaration of function 'up'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Stanse found an ommitted pci_dev_put on one error path in
cpcihp_generic_init. The path is taken on !dev, but also when
dev->hdr_type != PCI_HEADER_TYPE_BRIDGE. However it omits to
pci_dev_put on the latter.
As it is fine to pass NULL to pci_dev_put, put it in there
uncoditionally.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Scott Murray <scott@spiteful.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
ibmphp driver currently maps only 1KB of ebda memory area into kernel address
space during driver initialization. This causes kernel oops when the driver is
modprobe'd and it accesses memory beyond 1KB within ebda segment. The first
byte of ebda segment actually stores the length of the ebda region in
Kilobytes. Hence make use of the length parameter and map the entire ebda
region.
Signed-off-by: Chandru Siddalingappa <chandru@linux.vnet.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Stanse found a cut&pasted memory leak in pciehp_queue_pushbutton_work
and shpchp_queue_pushbutton_work. info is not freed/assigned on all
paths. Fix that.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No longer needed and causes build breakage.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Move the max_bus_speed and cur_bus_speed into the pci_bus. Expose the
values through the PCI slot driver instead of the hotplug slot driver.
Update all the hotplug drivers to use the pci_bus instead of their own
data structures.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
These enums must not overlap anyway, since we only have a single
pci_bus_speed_strings array. Use a single enum, and move it to
pci.h. Add 'SPEED' to the pcie names to make it clear what they are.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Rename add_range() to add_bus_range() to avoid conflict with the
naming of the generic range manipulation functions.
LKML-Reference: <1265793639-15071-4-git-send-email-yinghai@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Callers (acpi_memhotplug.c, dock.c and others) check for the return
value of acpi_bus_add() and assume a valid device was returned in
case zero was returned.
Thus return -ENODEV if no device was found in acpi_bus_scan and
propagate this through acpi_bus_add and acpi_bus_start.
Also remove a confusing comment in acpiphp_glue.c, acpi_bus_scan
will and cannot invoke if acpi_bus_add returns no valid device.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
If we stop the kthread, we may end up up'ing the sem twice, which seems
unintended.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Ian Campbell