Change state only if power on was succesful.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move dsi_bus_lock/unlock() out of taal_power_on/off() to avoid deadlock
in taal_esd_work().
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Bail out from taal_enable_te() and taal_run_test() if panel is not
enabled.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Check return values and bail out on errors.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
ESD work is never queued in probe, no need to cancel it on probe error.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Separate gpio_request() and request_irq() error handling.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
After the addition of proper hardware reset, taal_hw_reset(), there's no
need for an additional platform enable/disable. Remove them.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Avoid potential race conditions in sysfs access to taal data.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Issue a proper reset pulse on the reset line instead of just doing power
on/off.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
taal_bl_update_status was missing locks to protect taal_data. This caused
a kernel crash randomly, as the code attempted to set the brightness while
the OMAP's DSI block was actually disabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Using nanoseconds as arguments to functions that set the DSI timeouts was
perhaps not so good idea. The timeouts are based on different DSI clocks,
so the possible range for the timeouts vary greatly depending on the
clocks. Also, the multipliers used with the timeouts cause big gaps in the
timeout range, meaning that the nanosecond based functions could cause the
timeout to be quite far from the intended value.
This patch changes the functions to take the plain tick values with the
multiplier enable/disable bits, and sets the TA/LP_RX/HS_TX timeouts to
maximum. While the timeouts could be much lower, the fact is that when
TA/LP_RX/HS_TX timeout happens, we are in an error situation and not in a
hurry anyway.
STOP_STATE_COUNTER is a different matter, but it is only used at
initialization time, and won't normally affect the performance.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Using the shared workqueue led to to a deadlock in the case where the
display was unblanked via keyboard.
What happens is something like this:
- User presses a key
context 1:
- drivers/char/keyboard.c calls schedule_console_callback()
- fb_unblank takes the console semaphore
- dsi bus lock is taken, and frame transfer is started (dsi bus lock is
left on)
- Unblank code tries to set the panel backlight, which tries to take dsi
bus lock, but is blocked while the frame transfer is going on
context 2, shared workqueue, console_callback in drivers/char/vt.c:
- Tries to take console semaphore
- Blocks, as console semaphore is being held by context 1
- No other shared workqueue work can be run
context 3, HW irq, caused by FRAMEDONE interrupt:
- Interrupt handler schedules framedone-work in shared workqueue
- Framedone-work is never ran, as the shared workqueue is blocked. This
means that the unblank thread stays blocked, which means that context 2
stays blocked.
While I think the real problem is in keyboard/virtual terminal code, using
a private workqueue in the DSI driver is perhaps safer and more robust
than using the shared one. The DSI works should not be delayed more than a
millisecond or so, and even if the private workqueue gives us no hard
promise of doing so, it's still safer bet than the shared workqueue.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
dsi_vc_flush_receive_data() is meant to dump data when something has gone
wrong, and thus we should use DSSERR, not DSSDBG.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Trigger WARN_ON() messages from various places in the code in case the
memory region is not currently locked.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
When more than one memory region needs to be lockd at the same time use
the memory region id to fix the order in which the locks are taken. Also
one needs to use the _nested() versions of the locking primitives. The
memory region id can serve as the lock class there as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
R/W semaphore is a good fit for the memory region locking pattern.
So use it.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Add locking to the memory regions to make sure the memory region size
won't be changed while some other piece of code is performing some
checks or setup based on that information.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Separate the memory region from the framebuffer device a little bit.
It's now possible to select the memory region used by the framebuffer
device using the new mem_idx parameter of omapfb_plane_info. If the
mem_idx is specified it will be interpreted as an index into the
memory regions array, if it's not specified the framebuffer's index is
used instead. So by default each framebuffer keeps using it's own
memory region which preserves backwards compatibility.
This allows cloning the same memory region to several overlays and yet
each overlay can be controlled independently since they can be
associated with separate framebuffer devices.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
In omapfb_enable_overlay() if the overlay state is already what we want
skip the set_overlay_info().
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
If video memory hasn't been allocate have check_fb_var() still check
most of the settings, just skip the ones involving the size of the
memory region. Also skip the memory address calculations in
omapfb_setup_overlay() if there's no memory.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Split the overlay address calculations into their own function.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
When there are multiple scaled overlays simply checking whether the update
area intersects any of them in order is not enough. If eg. VID1 starts out
completely outside the update area but VID2 causes the update area to
increase in such a way that VID1 now falls partially within the increased
update area VID1 should be rechecked and the update area possibly
increased even further to fully encompass VID1. So simply keep looping
over the overlays until such time that none of the overlays caused the
update area to change.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
When DSS transitions from off mode to on VENC may generate a spurious
SYNC_LOST_DIGIT error. Just ack it when restoring the context. Also
restore IRQENABLE last to avoid triggering interrupts before the
context is fully restored.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
When the display is not active make the wait_for_go() functions return
immediately.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Check whether the display actually has the set_update_mode() function
before calling it. Only the sysfs codepath was broken, the omapfb ioctl
had the necessary protection.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
For some reason screen updates of certain odd widths seem to be triggering
HS TX timeouts on OMAP 3430, even if bigger updates do not. The reason for
this is unknown, but increasing the timeout removes the problem with no
(so far) noticeable problems. I haven't seen this problem on OMAP 3630.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Add a mutex_unlock missing on the error paths. The use of the mutex is
balanced elsewhere in the file.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E1;
@@
* mutex_lock(E1,...);
<+... when != E1
if (...) {
... when != E1
* return ...;
}
...+>
* mutex_unlock(E1,...);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Perform graceful cleanup on errors instead of just bailing out.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move a number of #ifdefs from code into dss.h and elsewhere, and
conditionally define no-op static inline functions, cleaning up the
code. This style is according to Documentation/SubmittingPatches.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
The driver set the background color canvas but never writes it in
DISPC_DEFAULT_COLOR_m register, which changes the background color
on the LCD or TV.
This patch adds a line to call to dispc_set_default_color() which is
the function in charge to write the DISPC_DEFAULT_COLOR_m register.
Signed-off-by: Carlos Lopez <carlos.cruz@sasken.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
In DPLL4 M3, M4, M5 and M6 field width has been increased by 1 bit in 3630.
So the max divider value that can be achived will be 32 and not 16.
In 3630 the functional clock is x1 of DPLL4 and not x2. Hence multiplier 2
is removed.
Signed-off-by: Sudeep Basavaraj <sudeep.basavaraj@ti.com>
Signed-off-by: Mukund Mittal <mmittal@ti.com>
Signed-off-by: Kishore Y <kishore.y@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Tested on OMAP3EVM for OMAP3530 and AM/DM 3730.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
[tomi.valkeinen@nokia.com: added slab.h include]
[tomi.valkeinen@nokia.com: added dependency to BACKLIGHT_CLASS_DEVICE]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
If omapdss_dsi_display_enable() failed the DSI bus was left locked. Also
if the operation failed later omapdss_dsi_display_disable() would get
called without holding the bus lock.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
There are some strange problems with DSI and updates with odd widths. One
particular problem is that HS TX timeout triggers easily with updates with
odd widths.
This patch makes the updates widths even, circumventing the problem. There
should be no ill side effects with increasing the update area slightly to
make the width even.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Only call driver disable when device isn't already disabled, which also
handles the driver not loaded case.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
platform_enable/disable() is already called in venc_power_on/off(), so
don't do it again in venc_panel_enable/disable().
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Give up if lock_fb_info() fails, following the same convention as other
lock_fb_info() users.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Framebuffer ioctl processing forces lock_fb_info() -> omapfb_lock()
locking order. Follow that order to avoid possible circular locking
dependency, detected by lockdep.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
This patch enables the use of vdds_sdi regulator in SDI subsystem.
We can disable the vdds_sdi voltage when not in use to save
power.
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Panel enable/disable is now done via the panel driver, so we should not
call the panel driver again
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
This allows us to disable DPI on systems that do not have it
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Values such as max_brightness should be set before backlights are
registered, but the current API doesn't allow that. Add a parameter to
backlight_device_register and update drivers to ensure that they
set this correctly.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Clk sources were not initialized, leading to kernel crash, or possibly to
strange behaviour if DSI was compiled in.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
In commit 2b0d8c251b the __early_param is
replaced with the generic early_param. This patch fixes the parameter passing
for the vram.
Signed-off-by: Thomas Weber <weber@corscience.de>
[tomi.valkeinen@nokia.com: changed the commit prefix]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Constify struct sysfs_ops.
This is part of the ops structure constification
effort started by Arjan van de Ven et al.
Benefits of this constification:
* prevents modification of data that is shared
(referenced) by many other structure instances
at runtime
* detects/prevents accidental (but not intentional)
modification attempts on archs that enforce
read-only kernel data at runtime
* potentially better optimized code as the compiler
can assume that the const data cannot be changed
* the compiler/linker move const data into .rodata
and therefore exclude them from false sharing
Signed-off-by: Emese Revfy <re.emese@gmail.com>
Acked-by: David Teigland <teigland@redhat.com>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove the option for forcing auto-update. Auto-update for manual update
displays is no more a DSS feature, so if a particular display devices does
have auto-update mode, it should be in display's custom settings.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
With the reworked model, DSI driver doesn't need to know anything about
external TE lines. Thus we can remove ext_te support, and only leave the
DSI TE trigger support.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move check/set/get_timings() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move set/get_wss() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move enable/disable/suspend/resume from omap_dss_device to
omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move update() and sync() from omap_dss_device to omap_dss_driver.
Also, update was hardcoded to use virtual channel 0. This patch adds a
parameter that specifies the VC.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move set/get_update_mode() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move enable/get_te() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move get_recommended_bpp() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move get_resolution() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move enable/disable_channel() from omap_dss_device to overlay manager.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move wait_vsync() from omap_dss_device to overlay manager.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move get/set_rotate() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move set/get_mirror() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move memory_read() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move run_test() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Remove performance measurement for auto-update. Auto-update and thus
performance measurement cannot be supported after the driver change where
the control is moved to display drivers.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Physical DSI bus is protected by a mutex. This patch changed the mutex to
a semaphore, so that we can lock and unlock the bus_lock from different
threads.
This is needed as the update process is started by user space program, and
thus the lock is acquired in that context, but the lock can be released in
different context, a work thread via irq.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
After changing the selection of DSI and DISPC clock source the users of
get_dsi/dispc_clk_source() functions were left unchanged.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
If there was a dss device without a driver and thus omapfb probe failed,
ref counts could be left to dss devices.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
The system to allow panel drivers to exists as attached to ctrl drivers
did never work very well. It is not useed, and this patch removes it to
make the driver cleaner.
For now, controller drivers need to include also the panel driver code. In
the future a proper mechanism for this should be developed, perhaps by
creating busses for controllers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
When OMAP PM layer is no-op/debug, the PM layer will increment context
loss count with every call. This resulted DSS2 to restore context
whenever a clock was enabled.
This commit checks the context loss count only when the context actually
could have been lost, ie. when enabling a clock when no clocks had been
previously enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Instead of configuring only VC0 to be usable, configure all four VCs
similarly. This is needed to utilize the other VCs.
Setting the FIFO sizes evenly for all VCs, regardless of how many VCs are
actually used, is not optimal. However, this affects only cases when
larger amounts of data are written or read via L4, meaning that normal use
cases are not affected.
At some point this could be optimized better to suit different use cases.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Rename and export dsi_vc_enable_hs() so that the display drivers can
control the mode of the DSI link.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
dss_select_clk_source() was rather confusing. Selecting the source with
enums is much clearer.
The clk source selection is also stored into memory, so that we know what
is the selected source, even when clocks are off. This is important during
setup, as we need to what clocks to turn on before the clocks are turned
on.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Previously the only place to get the size of the display was from the
DSS's sysfs interface, making, for example, configuring overlays and doing
updates on manual displays more difficult.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
The workqueue creation error branch attempted to destroy a NULL wq,
and, in turn, a failed registration does not destroy the newly created
workqueue.
The problem was reported by a static analysis tool.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
The regulator is now enabled by DSS driver, and thus the panel driver
doesn't need to touch it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
It looks like on OMAP3 some DSS pins need VDDS_DSI to function properly.
This has not been confirmed from TI, but looking at figure 15-1 "Display
subsystem highlight" from the TRM, some data pins come near the DSI and SDI
blocks. This is not very hard evidence, but the fact remains that with the
power on, pixels are ok, and with the power off, pixels are not ok.
It may also be that VDDS_SDI is needed to power some pins, but as normally
both VDDS_SDI and VDDS_DSI come from the same power source, this hasn't
been shown.
It seems that a single driver can only get a regulator once. This patch
solves it by getting all the required regulators in one place, and from
which the submodules then get the regulators they need.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Add support of TPO TD043MTEA1 TFT LCD panel to DSS2 driver.
This panel is used by OMAP3 Pandora device.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
If the panel's probe had failed, omapfb would still go on, eventually
crashing.
A better fix would be to handle each display properly, and leaving just
the failed display out. But that is a bigger change.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
If the scaling ratio is below 0.5 video output width can't be identical
to the display width. Reject such settings.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Loops checking for certain condition were rather inconsistent.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Reported-by: Juha Leppanen <juha_motorsportcom@luukku.com>
Fixes bug causing VRFB memory area to be released twice.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Reported-by: Eino-Ville Talvala <talvala@stanford.edu>
Collect interrupt statistics, printable via debugfs:
debugfs/omapdss/dispc_irq
debugfs/omapdss/dsi_irq
The counters are reset when printed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
- dsi_vc_send_short() needs to use dest_per for the peripheral id
- dsi_vc_send_null() was always using channel id 0
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
The core files of DSS2. DSS2 commits are split a bit artificially to
make the individual commits smaller, and DSS2 doesn't compile properly
without the rest of the core commits. This shouldn't be a problem, as no
configuration uses DSS2 yet.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
VRFB rotation engine is a block in OMAP2/3 that offers 12 independent
contexts that can be used for framebuffer rotation.
Each context has a backend area of real memory, where it stores the
pixels in undisclosed format. This memory is offered to users via 4
virtual memory areas, which see the same memory area in different
rotation angles (0, 90, 180 and 270 degrees).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Add a Video RAM manager for OMAP 2 and 3 platforms. VRAM manager is used
to allocate large continuous blocks of SDRAM or SRAM. The features VRAM
manager has that are missing from dma_alloc_* functions are:
- Support for OMAP2's SRAM
- Allocate without ioremapping
- Allocate at defined physical addresses
- Allows larger VRAM area and larger allocations
The upcoming DSS2 uses VRAM manager.
VRAM area size can be defined in kernel config, board file or with
kernel boot parameters. Board file definition overrides kernel config,
and boot parameter overrides kernel config and board file.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>