We have few fedora bug reports about list corruption on pinctrl,
for example:
https://bugzilla.redhat.com/show_bug.cgi?id=1051918
Most likely corruption happen due lack of protection of pinctrl_list
when adding new nodes to it. Patch corrects that.
Fixes: 42fed7ba44 ("pinctrl: move subsystem mutex to pinctrl_dev struct")
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
according to datasheet and ac97_muxmask assignment, ac97_pins should be
corrected.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The offset for the 2bit register calculate wrong, this patch
fixes the problem. The debugfs printout for oconf, iconfa, iconfb
now shows the real values.
Cc: stable@vger.kernel.org
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Reviewed-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Due to an assumption in the VT8500 pinctrl driver, the value passed
from devicetree for 'wm,pull' was not explicitly translated before
being passed to pinconf.
Since v3.10, changes to 'enum pin_config_param', PIN_CONFIG_BIAS_PULL_(UP/DOWN)
no longer map 1-to-1 with the expected values in devicetree.
This patch adds a small translation between the devicetree values (0..2)
and the enum pin_config_param equivalent values.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The offset to ICONFB was incorrect, this patch set the correct value 0x14.
dev_dbg in function imx1_write_2bit print the wrong address and had been
moved after address calculation.
Cc: stable@vger.kernel.org
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Reviewed-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When setting the gpio irq type, use the __irq_set_handler_locked()
variant instead of the irq_set_handler() to prevent false
spinlock recursion warning.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@vger.kernel.org> # v3.12
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
DT and DT-conversion-related changes for various ARM platforms. Most
of these are to enable various devices on various boards, etc, and not
necessarily worth enumerating.
New boards and systems continue to come in as new devicetree files that
don't require corresponding C changes any more, which is indicating that
the system is starting to work fairly well.
A few things worth pointing out:
* ST Ericsson ux500 platforms have made the major push to move over to fully
support the platform with DT.
* Renesas platforms continue their conversion over from legacy platform devices
to DT-based for hardware description.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4o2d
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"DT and DT-conversion-related changes for various ARM platforms. Most
of these are to enable various devices on various boards, etc, and not
necessarily worth enumerating.
New boards and systems continue to come in as new devicetree files
that don't require corresponding C changes any more, which is
indicating that the system is starting to work fairly well.
A few things worth pointing out:
* ST Ericsson ux500 platforms have made the major push to move over
to fully support the platform with DT
* Renesas platforms continue their conversion over from legacy
platform devices to DT-based for hardware description"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (327 commits)
ARM: dts: SiRF: add pin group for USP0 with only RX or TX frame sync
ARM: dts: SiRF: add lost usp1_uart_nostreamctrl pin group for atlas6
ARM: dts: sirf: add lost minigpsrtc device node
ARM: dts: sirf: add clock, frequence-voltage table for CPU0
ARM: dts: sirf: add lost bus_width, clock and status for sdhci
ARM: dts: sirf: add lost clocks for cphifbg
ARM: dts: socfpga: add pl330 clock
ARM: dts: socfpga: update L2 tag and data latency
arm: sun7i: cubietruck: Enable the i2c controllers
ARM: dts: add support for EXYNOS4412 based TINY4412 board
ARM: dts: Add initial support for Arndale Octa board
ARM: bcm2835: add USB controller to device tree
ARM: dts: MSM8974: Add MMIO architected timer node
ARM: dts: MSM8974: Add restart node
ARM: dts: sun7i: external clock outputs
ARM: dts: sun7i: Change 32768 Hz oscillator node name to clk@N style
ARM: dts: sun7i: Add pin muxing options for clock outputs
ARM: dts: sun7i: Add rtp controller node
ARM: dts: sun5i: Add rtp controller node
ARM: dts: sun4i: Add rtp controller node
...
New drivers
- Samsung Maxim 14577; Micro USB, Regulator, IRQ Controller and Battery Charger
- TI/National Semiconductor LP3943 I2C GPIO Expander and PWM Generator
Existing driver adaptions
- Expansion of Wolfson Arizona DSP and High-Pass filter controls
- TI TWL6040 default Regmap support and Regcache addition/bypass
- Some nice Smatch catch fixes
- Conversion of TI OMAP-USB and TI TWL6030 to endian neutralness
- ChromeOS EC timing (delay) adaptions and added dependency on OF
- Many constifications of 'struct {mfd_cell,regmap_irq,et. al}'
- Watchdog support added for NVIDIA AS3722
- Convert functions to static in TI AM335x
- Realigned previously defeated functionality in TI AM335x
- IIO ADC-TSC concurrency dead-lock/timeout resolution
- Addition of Power Management and Clock support for Samsung core
- DEFINE_PCI_DEVICE_TABLE macro removal from MFD Subsystem
- Greater use of irqdomain functionality in ST-E AB8500
- Removal of 'include/linux/mfd/abx500/ab8500-gpio.h'
- Wolfson WM831x PMIC Power Management changes s/poweroff/shutdown/
- Device Tree documentation added for TI/Nat Semi LP3943
- Version detection and voltage tables for TI TPS6586x PMIC devices
- Simplification of Freescale MC13XXX (de-)initialisation routines
- Clean-up and simplification of the Realtek parent driver
- Added support for RTL8402 Realtek PCI-Express card reader
- Resource leak fix for Maxim 77686
- Possible suspend BUG() fix in OMAP USB TLL
- Support for new Wolfson WM5110 Revision (D)
- Testing of automatic assignment of of_node in mfd_add_device()
- Reversion of the above when it started to cause issues
- Remove legacy Platform Data from;
TI TWL Core, Qualcomm SSBI and ST-E ABx500 Pinctrl
- Clean-ups; tabbing issues, function name changes, 'drvdata = NULL' removal,
unused uninitialised warning mitigation, error message clarity,
removal of redundant/duplicate checks, licensing (GPL -> GPL2),
coding consistency, duplicate function declaration, ret checks,
commit corrections, redundant of_match_ptr() helper removal,
spelling, #if-deffery removal and header guards name changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=PuTE
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.14-1' of git://git.linaro.org/people/ljones/mfd
Pull MFD changes from Lee Jones:
"New drivers
- Samsung Maxim 14577; Micro USB, Regulator, IRQ Controller and
Battery Charger
- TI/National Semiconductor LP3943 I2C GPIO Expander and PWM
Generator
Existing driver adaptions
- Expansion of Wolfson Arizona DSP and High-Pass filter controls
- TI TWL6040 default Regmap support and Regcache addition/bypass
- Some nice Smatch catch fixes
- Conversion of TI OMAP-USB and TI TWL6030 to endian neutralness
- ChromeOS EC timing (delay) adaptions and added dependency on OF
- Many constifications of 'struct {mfd_cell,regmap_irq,et.al}'
- Watchdog support added for NVIDIA AS3722
- Convert functions to static in TI AM335x
- Realigned previously defeated functionality in TI AM335x
- IIO ADC-TSC concurrency dead-lock/timeout resolution
- Addition of Power Management and Clock support for Samsung core
- DEFINE_PCI_DEVICE_TABLE macro removal from MFD Subsystem
- Greater use of irqdomain functionality in ST-E AB8500
- Removal of 'include/linux/mfd/abx500/ab8500-gpio.h'
- Wolfson WM831x PMIC Power Management changes s/poweroff/shutdown/
- Device Tree documentation added for TI/Nat Semi LP3943
- Version detection and voltage tables for TI TPS6586x PMIC devices
- Simplification of Freescale MC13XXX (de-)initialisation routines
- Clean-up and simplification of the Realtek parent driver
- Added support for RTL8402 Realtek PCI-Express card reader
- Resource leak fix for Maxim 77686
- Possible suspend BUG() fix in OMAP USB TLL
- Support for new Wolfson WM5110 Revision (D)
- Testing of automatic assignment of of_node in mfd_add_device()
- Reversion of the above when it started to cause issues
- Remove legacy Platform Data from;
TI TWL Core, Qualcomm SSBI and ST-E ABx500 Pinctrl
- Clean-ups; tabbing issues, function name changes, 'drvdata = NULL'
removal, unused uninitialised warning mitigation, error
message clarity, removal of redundant/duplicate checks,
licensing (GPL -> GPL2), coding consistency, duplicate
function declaration, ret checks, commit corrections,
redundant of_match_ptr() helper removal, spelling,
#if-deffery removal and header guards name changes"
* tag 'mfd-3.14-1' of git://git.linaro.org/people/ljones/mfd: (78 commits)
mfd: wm5110: Add register patch for rev D chip
mfd: omap-usb-tll: Don't hold lock during pm_runtime_get/put_sync()
gpio: lp3943: Remove redundant of_match_ptr helper
mfd: sta2x11-mfd: Use named constants for pci_power_t values
Documentation: mfd: Fix LDO index in s2mps11.txt
mfd: Cleanup mfd-mcp-sa11x0.h header
mfd: max8997: Use "IS_ENABLED(CONFIG_OF)" for DT code.
mfd: twl6030: Fix endianness problem in IRQ handler
mfd: sec-core: Add cells for S5M8767-clocks
mfd: max14577: Remove redundant of_match_ptr helper
mfd: twl6040: Fix sparse non static symbol warning
mfd: Revert "mfd: Always assign of_node in mfd_add_device()"
mfd: rtsx: Fix sparse non static symbol warning
mfd: max77693: Set proper maximum register for MUIC regmap
mfd: max77686: Fix regmap resource leak on driver remove
mfd: Represent correct filenames in file headers
mfd: rtsx: Add support for card reader rtl8402
mfd: rtsx: Add set pull control macro and simplify rtl8411
mfd: max8997: Enforce mfd_add_devices() return value check
mfd: mc13xxx: Simplify probe() & remove()
...
- New driver for the Qualcomm TLMM pin controller and its
msm8x74 subdriver.
- New driver for the Broadcom Capri BCM281xx SoC.
- New subdriver for the imx25 pin controller.
- New subdriver for the Tegra124 pin controller.
- Lock GPIO lines as IRQs for select combined pin control and
GPIO drivers for baytrail and sirf.
- Some semi-big refactorings and extenstions to the sirf
driver.
- Lots of patching, cleanup and fixing in the Renesas "PFC"
driver and associated subdrivers as usual. It is settling
down a little bit now it seems.
- Minor fixes and incremental updates here and there as usual.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ol2E
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull bulk pin control changes from Linus Walleij:
"This has been queued and tested for a while. Lots of action here,
like in the GPIO tree, embedded stuff like this is really hot now it
seems. Details in the signed tag. I'm especially happy about the
Qualcomm driver as it is used in such a huge subset of mobile handsets
out there, and these platforms in general need better upstream support
- New driver for the Qualcomm TLMM pin controller and its msm8x74
subdriver.
- New driver for the Broadcom Capri BCM281xx SoC.
- New subdriver for the imx25 pin controller.
- New subdriver for the Tegra124 pin controller.
- Lock GPIO lines as IRQs for select combined pin control and GPIO
drivers for baytrail and sirf.
- Some semi-big refactorings and extenstions to the sirf driver.
- Lots of patching, cleanup and fixing in the Renesas "PFC" driver
and associated subdrivers as usual. It is settling down a little
bit now it seems.
- Minor fixes and incremental updates here and there as usual"
* tag 'pinctrl-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (72 commits)
pinctrl: sunxi: Honor GPIO output initial vaules
pinctrl: capri: add dependency on OF
ARM: bcm11351: Enable pinctrl for Broadcom Capri SoCs
ARM: pinctrl: Add Broadcom Capri pinctrl driver
pinctrl: Add pinctrl binding for Broadcom Capri SoCs
pinctrl: Add void * to pinctrl_pin_desc
pinctrl: st: Fix a typo in probe
pinctrl: Fix some typos and grammar issues in the documentation
pinctrl: sirf: lock IRQs when starting them
pinctrl: sirf: put gpio interrupt pin into input status automatically
pinctrl: sirf: use only one irq_domain for the whole device node
pinctrl: single: fix infinite loop caused by bad mask
pinctrl: single: fix pcs_disable with bits_per_mux
pinctrl: single: fix DT bindings documentation
pinctrl: as3722: Set pin to output mode for some function
pinctrl: sirf: add pin group for USP0 with only RX or TX frame sync
pinctrl: sirf: fix the pins of sdmmc5 connected with TriG
pinctrl: sirf: add lost usp1_uart_nostreamctrl group for atlas6
pinctrl: sunxi: Add Allwinner A20 clock output pin functions
pinctrl/lantiq: fix typo
...
A big set this merge window, as we have much going on in
this subsystem. Major changes this time:
- Some core improvements and cleanups to the new GPIO
descriptor API. This seems to be working now so we can
start the exodus to this API, moving gradually away from
the global GPIO numberspace.
- Incremental improvements to the ACPI GPIO core, and move
the few GPIO ACPI clients we have to the GPIO descriptor
API right *now* before we go any further. We actually
managed to contain this *before* we started to litter
the kernel with yet another hackish global numberspace for
the ACPI GPIOs, which is a big win.
- The RFkill GPIO driver and all platforms using it have
been migrated to use the GPIO descriptors rather than
fixed number assignments. Tegra machine has been migrated
as part of this.
- New drivers for MOXA ART, Xtensa GPIO32 and SMSC SCH311x.
Those should be really good examples of how I expect a
nice GPIO driver to look these days.
- Do away with custom GPIO implementations on a major
part of the ARM machines: ks8695, lpc32xx, mv78xx0.
Make a first step towards the same in the horribly
convoluted Samsung S3C include forest. We expect to
continue to clean this up as we move forward.
- Flag GPIO lines used for IRQ on adnp, bcm-kona, em,
intel-mid and lynxpoint.
This makes the GPIOlib core aware that a certain GPIO line
is used for IRQs and can then enforce some semantics such
as disallowing a GPIO line marked as in use for IRQ to be
switched to output mode.
- Drop all use of irq_set_chip_and_handler_name().
The name provided in these cases were just unhelpful
tags like "mux" or "demux".
- Extend the MCP23s08 driver to handle interrupts.
- Minor incremental improvements for rcar, lynxpoint, em
74x164 and msm drivers.
- Some non-urgent bug fixes here and there, duplicate
#includes and that usual kind of cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lW2i
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO tree bulk changes from Linus Walleij:
"A big set this merge window, as we have much going on in this
subsystem. The changes to other subsystems (notably a slew of ARM
machines as I am doing away with their custom APIs) have all been
ACKed to the extent possible.
Major changes this time:
- Some core improvements and cleanups to the new GPIO descriptor API.
This seems to be working now so we can start the exodus to this
API, moving gradually away from the global GPIO numberspace.
- Incremental improvements to the ACPI GPIO core, and move the few
GPIO ACPI clients we have to the GPIO descriptor API right *now*
before we go any further. We actually managed to contain this
*before* we started to litter the kernel with yet another hackish
global numberspace for the ACPI GPIOs, which is a big win.
- The RFkill GPIO driver and all platforms using it have been
migrated to use the GPIO descriptors rather than fixed number
assignments. Tegra machine has been migrated as part of this.
- New drivers for MOXA ART, Xtensa GPIO32 and SMSC SCH311x. Those
should be really good examples of how I expect a nice GPIO driver
to look these days.
- Do away with custom GPIO implementations on a major part of the ARM
machines: ks8695, lpc32xx, mv78xx0. Make a first step towards the
same in the horribly convoluted Samsung S3C include forest. We
expect to continue to clean this up as we move forward.
- Flag GPIO lines used for IRQ on adnp, bcm-kona, em, intel-mid and
lynxpoint.
This makes the GPIOlib core aware that a certain GPIO line is used
for IRQs and can then enforce some semantics such as disallowing a
GPIO line marked as in use for IRQ to be switched to output mode.
- Drop all use of irq_set_chip_and_handler_name(). The name provided
in these cases were just unhelpful tags like "mux" or "demux".
- Extend the MCP23s08 driver to handle interrupts.
- Minor incremental improvements for rcar, lynxpoint, em 74x164 and
msm drivers.
- Some non-urgent bug fixes here and there, duplicate #includes and
that usual kind of cleanups"
Fix up broken Kconfig file manually to make this all compile.
* tag 'gpio-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (71 commits)
gpio: mcp23s08: fix casting caused build warning
gpio: mcp23s08: depend on OF_GPIO
gpio: mcp23s08: Add irq functionality for i2c chips
ARM: S5P[v210|c100|64x0]: Fix build error
gpio: pxa: clamp gpio get value to [0,1]
ARM: s3c24xx: explicit dependency on <plat/gpio-cfg.h>
ARM: S3C[24|64]xx: move includes back under <mach/> scope
Documentation / ACPI: update to GPIO descriptor API
gpio / ACPI: get rid of acpi_gpio.h
gpio / ACPI: register to ACPI events automatically
mmc: sdhci-acpi: convert to use GPIO descriptor API
ARM: s3c24xx: fix build error
gpio: f7188x: set can_sleep attribute
gpio: samsung: Update documentation
gpio: samsung: Remove hardware.h inclusion
gpio: xtensa: depend on HAVE_XTENSA_GPIO32
gpio: clps711x: Enable driver compilation with COMPILE_TEST
gpio: clps711x: Use of_match_ptr()
net: rfkill: gpio: convert to descriptor-based GPIO interface
leds: s3c24xx: Fix build failure
...
This deletes the special AB8500 GPIO platform data passing
header and merges the few remaining contents down into the
abx500 pinctrl driver which handles the abx500 GPIO device.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
All instances of this device are now coming from device tree-
enabled platforms probing without using platform data.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some GPIO users, such as fixed-regulator, request GPIO output with
initial value of 1. This was ignored by sunxi driver.
Cc: stable@vger.kernel.org
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit f6308b36c4 (ACPI: Add BayTrail SoC GPIO and LPSS
ACPI IDs), because it causes the Alan Cox' ASUS T100TA to "crash and
burn" during boot if the Baytrail pinctrl driver is compiled in.
Fixes: f6308b36c4 (ACPI: Add BayTrail SoC GPIO and LPSS ACPI IDs)
Reported-by: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Requested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As this driver is using pinconf_generic_dt_node_to_map_pin() it
needs to depend on OF so as not to cause build problems on
archs that do not support OF.
Cc: Sherman Yin <syin@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adds pinctrl driver for Broadcom Capri (BCM281xx) SoCs.
v4: - PINCTRL selected in Kconfig, PINCTRL_CAPRI selected in bcm_defconfig
- make use of regmap
- change CAPRI_PIN_UPDATE from macro to inline function.
- Handle pull-up strength arg in Ohm instead of enum
v3: Re-work driver to be based on generic pin config. Moved config selection
from Kconfig to bcm_defconfig.
v2: Use hyphens instead of underscore in DT property names.
Signed-off-by: Sherman Yin <syin@broadcom.com>
Reviewed-by: Christian Daudt <bcm@fixthebug.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Probe function had commas instead of semi-colons on some of the lines.
This patch just fixes those lines. No functional chagnes done in this
patch.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This uses the new API for tagging GPIO lines as in use by
IRQs. This enforces a few semantic checks on how the underlying
GPIO line is used.
Also assign the gpio_chip.dev pointer to be used for error
messages.
Cc: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
busses like i2c, spi and so on can parse the virq of their subnode automatically by
irq_of_parse_and_map(). for example, i2c will do that in of_i2c_register_devices().
people can put hwirq number attached to a gpio controller in dts, and drivers can
directly request the parsed virq.
for example, for an i2c client as below,
tangoc-ts@5c{
compatible = "pixcir,tangoc-ts";
interrupt-parent = <&gpio>;
interrupts = <3 0>;
reg = <0x5c>;
};
in i2c client probe(), it will request_irq(client->irq, ...) without
calling gpio_direction_input().
so here when we set irq type, we also put the pin to input direction.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
in sirfsoc gpio probe(), we create 5 irq_domains for 5 gpio banks. but
in irq_create_of_mapping() of irqchip core level, irq_find_host() can
only return the 1st irq_domain attached the pinctrl dt device node as
we can see from the codes:
unsigned int irq_create_of_mapping(struct device_node *controller,
const u32 *intspec, unsigned int intsize)
{
struct irq_domain *domain;
...
domain = controller ? irq_find_host(controller) : irq_default_domain;
}
struct irq_domain *irq_find_host(struct device_node *node)
{
struct irq_domain *h, *found = NULL;
int rc;
/* We might want to match the legacy controller last since
* it might potentially be set to match all interrupts in
* the absence of a device node. This isn't a problem so far
* yet though...
*/
mutex_lock(&irq_domain_mutex);
list_for_each_entry(h, &irq_domain_list, link) {
if (h->ops->match)
rc = h->ops->match(h, node);
else
rc = (h->of_node != NULL) && (h->of_node == node);
if (rc) {
found = h;
break;
}
}
mutex_unlock(&irq_domain_mutex);
return found;
}
for sirfsoc, the 1st irq_domain attached to the device_node(controller) only
can do linear for the 1st 32 gpios. so for devices who use gpio hwirq above
32 and put the information in dt like:
tangoc-ts@5c{
compatible = "pixcir,tangoc-ts";
+ interrupt-parent = <&gpio>;
+ interrupts = <34 0>;
};
we will fail to get the virq for these devices as hwirq will be bigger than
domain->revmap_data.linear.size in:
unsigned int irq_linear_revmap(struct irq_domain *domain,
irq_hw_number_t hwirq)
{
/* Check revmap bounds; complain if exceeded */
if (WARN_ON(hwirq >= domain->revmap_data.linear.size))
return 0;
return domain->revmap_data.linear.revmap[hwirq];
}
this patch drops redundant irq_domain and keep only one to fix the problem.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit 4e7e8017a8 (pinctrl: pinctrl-single:
enhance to configure multiple pins of different modules) improved
support for pinctrl-single,bits option, but also caused a regression
in parsing badly configured mask data.
If the masks in DT data are not quite right,
pcs_parse_bits_in_pinctrl_entry() can end up in an infinite loop,
trashing memory at the same time.
Add a check to verify that each loop actually removes bits from the
'mask', so that the loop can eventually end.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pcs_enable() uses vals->mask instead of pcs->fmask when bits_per_mux is
enabled. However, pcs_disable() always uses pcs->fmask.
Fix pcs_disable() to use vals->mask with bits_per_mux.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If pins are used for function output like pwm, clk32k,
power good etc then set it as output mode default.
Signed-off-by: Mallikarjun Kasoju <mkasoju@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of asking each driver to register to ACPI events we can just call
acpi_gpiochip_register_interrupts() for each chip that has an ACPI handle.
The function checks chip->to_irq and if it is set to NULL (a GPIO driver
that doesn't do interrupts) the function does nothing.
We also add the a new header drivers/gpio/gpiolib.h that is used for
functions internal to gpiolib and add ACPI GPIO chip registering functions
to that header.
Once that is done we can remove call to acpi_gpiochip_register_interrupts()
from its only user, pinctrl-baytrail.c
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
USP0 has multiple functions, and has RX and TX frame sync signals,
for some scenarios like audio PCM, we don't need both of them.
so here we add two possibilities for USP0 only holding one of TX
and RX frame sync.
Signed-off-by: Rongjun Ying <Rongjun.Ying@csr.com>
Signed-off-by: Barry Song <Barry.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
sdmmc5 has only 3 pins CMD, CLK, DATA which are connected with CSR
TriG RF multi-GNSS. The hardware connection is like:
DATA -- GPS_SGN
CLK -- GPS_RF_CLK
CMD -- GPS_MAG
here we drop redundant pins in sdmmc5 group.
Signed-off-by: Bin Shi <Bin.Shi@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit af614b2301 adds lost USP-based UART pin groups for prima2,
but missed usp1_uart_nostreamctrl group for atlas6, this patch fixes it.
this makes USP(Universal Serial Ports) port1 can work as uart without
stream ctrl.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds the clock output pin functions on the A20.
The 2 pins can output a configurable clock to be used by
external modules. This is used on the CubieTruck, to supply
a 32768 Hz low power clock to the onboard Wifi+BT module.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds VIN[0-2] pinmux support to r8a7791 SoC.
VIN1 B mirror is also added along with the primary
configuration since it's the only one that provides
access to all 24 data bits on VIN1.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This groups USB PWEN and OVC pins together on R8A7791 SoC,
the same way it's done on R8A7790, since both are needed
for a USB device.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Bringing in the tegra dma/reset framework cleanup as a base for the DT changes.
* tegra/dma-reset-rework: (320 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
The arrays are never modified, declare them as const.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The arrays are never modified, declare them as const.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The arrays are never modified, make them const.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The enum_ids and var_field_width fields of struct pinmux_data_reg and
pinmux_cfg_reg are initialized using compound literals. Cast them to
const to store them in .rodata.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Set g->out_bit bit for gpio output high, clear g->out_bit bit for gpio output
low.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace the clk_prepare and clk_enable calls by a single
clk_prepare_enable call.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
clk_unprepare shall be called before clk_disable.
Fix the issue by replacing the clk_unprepare and clk_disable calls by a
single clk_disable_unprepare call.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit adds slew-rate and input-enable/disable support for pinconf
-generic.
Signed-off-by: Sherman Yin <syin@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the more specific form 8974 for the compatible to reduce the
risk of future mishaps.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make the bitmaps part of the msm_pinctrl allocation instead of
separately allocating them.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add GPIOLIB and OF as dependencies for PINCTRL_MSM8X74, to fix
build errors from i386-randconfig.
Also add help text and make the entries tristate, while touching
these entries.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
[Rebased on top of pin control development branch]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This allows to get the pin configuration by using debugfs. On my system:
# cat /sys/kernel/debug/pinctrl/pinctrl.3/pinconf-pins
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a driver for the Tegra124 pinmux, and required
parameterization data for Tegra124.
The driver uses the common Tegra pincontrol driver utility
functions to implement the majority of the driver.
This driver is not compatible with the earlier NVIDIA's SoCs,
hence add new compatibile as "nvidia,tegra124-pinmux".
Originally written by Ashwini Gguhe.
Thierry:
- Cleanups in patches.
ldewangan:
- Fix some entries for groups.
- Fix MUX enums and group sequence.
Signed-off-by: Ashwini Ghuge <aghuge@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
CC: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On non-DT platforms IRQ controllers associated with the GPIOs have a
fixed IRQ base value known at compile time. The sh-pfc driver translates
GPIO number to IRQ numbers using a hardcoded table. This mechanism
breaks on DT platforms, as the IRQ base values are dynamic in that case.
Fix this by specifying IRQs associated with GPIOs in IRQ resources,
populated automatically from the device tree. When IRQ resources are
specified the driver requires one IRQ resource per GPIO able to generate
an interrupt, and uses the translation table to compute the IRQ resource
offset instead of the IRQ number.
Cc: devicetree@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There's more than one window, name the field windows.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes catching duplicate entries easier. Merge the two IRQ9 entries
found after sorting.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The external IRQ15 input multiplexed on GPIO 0 is missing. Add it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
0 is a valid GPIO value, use -1 to terminate the gpios array in IRQ
lists.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some indices take positive values only, make them unsigned.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ops->pin_config_get() is only used in one specific path that will only be taken
for generic pinconf drivers (ops->is_generic == true) when dumping the pinconf
by using debugfs.
By removing the check in pinconf_check_ops(), let's stop pressuring people to
write a pin_config_get() function that will never be used and so will probably
never be tested.
Removing the check in pinconf_pins_show() allows driver to not implement
pin_config_get() but still get a dump of the pinconf in debugfs by implementing
pin_config_dbg_show().
Finally, not implementing pin_config_get() now results in returning -ENOTSUPP
instead of -EINVAL. While this doesn't have any real impact for now, this feels
more right.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When passing a not initialized config parameter, at91_pinconf_get() would return
a bogus value. Fix that by initializing it to zero before using it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are VIN2 and VIN3 channels available on the R8A7790 SoC.
VIN2 supports 4/8/16/18/24-bit data, while VIN3 supports 8-bit.
Add both here, covering all possible data pin configurations.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Both VIN0 and VIN1 channels support identical input interfaces.
Add missing VIN1 pins here and organize them in the same pin
groups as VIN0.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
This reorganizes and renames VIN0 data pin groups to cover
all possible configurations. There's total of eight data
pin groups, one per each configuration. Most of the groups
share the same pin/mux array. Only the 18-bit configuration
needs a separate pin/mux array since in combines interleaved
data pins.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
This groups VIN0 HSYNC and VSYNC pins together
since one cannot be used without another.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
This drops superfluous "signal" word from the pin group names
and renames data_enable group to clkenb as in the h/w manual.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The macro is defined identically in four different locations. Share it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Commit 7cbb0e55e2 ("sh-pfc: Don't duplicate argument to PINMUX_GPIO
macro") erronesouly modified the PINMUX_GPIO macro in a way that
resulted in all pins being named "name". Fix the macro to name the pins
correctly.
Cc: stable@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We had a compilation failure on x86_64 due to missing OF support
as this was an implicit dependency. Add an explicit dependency
on OF and OF_IRQ on the SoC driver.
Cc: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
ChangeLog v2->v3:
- Total failure with older approaches: what we need to do is
have the *SoC subdriver* depend on OF and OF_IRQ. This is
because the placeholder bool PINCTRL_MSM cannot cascade its
dependencies when a subdriver selects it, Kconfig is smart
but not that smart.
ChangeLog v1->v2:
- OK so "depends on OF" did not work here let's try to simply
select OF and OF_IRQ for this then? It's one of those
"warning: (PINCTRL_MSM8X74) selects PINCTRL_MSM which has
unmet direct dependencies (PINCTRL && OF)" that I simply
cannot find my way out of :-/
This uses the new API for tagging GPIO lines as in use by
IRQs. This enforces a few semantic checks on how the underlying
GPIO line is used.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add initial definition of parameters for pinctrl-msm for the msm8x74
platform.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a pinctrl, pinmux, pinconf and gpiolib driver for the
Qualcomm TLMM block.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This switches the two members of struct gpio_chip that were
defined as unsigned foo:1 to bool, because that is indeed what
they are. Switch all users in the gpio and pinctrl subsystems
to assign these values with true/false instead of 0/1. The
users outside these subsystems will survive since true/false
is 1/0, atleast we set some kind of more strict typing example.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When computing the pin configuration register offset the bias setup code
erroneously compares the pin number range with the loop index instead of
the pin number. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When computing the pin configuration register offset the bias setup code
erroneously compares the pin number range with the loop index instead of
the pin number. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The default gpiolib debug output shows pin labels.
We want baytrail custom debug output to have the same functionality.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the new ACPI ID (INT33FC) for the BayTrail GPIO
banks as seen on a BayTrail M System-On-Chip platform. This
ACPI ID is used by the BayTrail GPIO (pinctrl) driver to
manage the Low Power Subsystem (LPSS).
Signed-off-by: Paul Drews <paul.drews@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After the patches deleting the last board registering this
pin controller as a platform device has been deleted,
proceed to remove the non-DT boot patch and depend on
OF being available and the device to be coming up by
a DT node.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This decomissions the platform data header (which is no longer
in use after the systems using this driver were switched to
a pure device-tree config path) and merges the result into
the driver file or local driver header.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is mostly cut and paste from the imx35 pinctrl driver.
The data was generated using sed and awk on
arch/arm/plat-mxc/include/mach/iomux-mx25.h.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: devicetree@vger.kernel.org
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Support gpio devicetree subnodes to allow a more detailed DT hardware
description.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The IMX/MXC selects USE_OF at architecture level, so the OF dependency
at individual SoC pinctrl driver level can just be dropped.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we now grab IRQs also without first reserving the GPIO
line, let's print the mapped IRQ unconditionally in the
debugfs file as well.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename the sync_1 group to sync as the device has a single sync pin
group for the DU, move the cde_disp mux array right after the
corresponding pins array, and split the clk_in pins in three separate
groups as the pins can be used independently.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to unlock here before returning -EINVAL.
Fixes: 6ca5274d1d ('pinctrl: rockchip: add rk3188 specifics')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I sent a patch to fix some bitwise AND tests but I guess I missed some.
Sorry about that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is a copy and paste bug so we test "info->reg_base" instead of
"info->reg_pull".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On OMAPs the IO ring must be rearmed each time the pad wakeup
configuration is changed. So call pcs_soc->rearm() from
pcs_irq_set().
As pinctrl-single is now an interrupt controller in some cases,
we should follow the standards and keep the interrupts enabled
constantly, and not just for wake-up events. The tracking of
runtime vs wake-up interrupts can be handled separately for
the automated runtime PM solution when we have it in the
future.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
[tony@atomide.com: removed wrong comment, updated description]
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Merged the GPIO descriptor API from Alexandre Courbot.
This is a first step toward trying to get rid of the
global GPIO numberspace for the future.
- Add an API so that driver can flag that a certain GPIO
line is being used by a irqchip backend for generating
IRQs, so that we can enforce checks, like not allowing
users to switch that line to an output at runtime, since
this makes no sense. Implemented corresponding calls
in a few select drivers.
- ACPI GPIO cleanups, refactorings and switch to using the
descriptor-based interface.
- Support for the TPS80036 Palmas GPIO variant.
- A new driver for the Broadcom Kona GPIO SoC IP block.
- Device tree support for the PCF857x driver.
- A set of ARM GPIO refactorings with the goal of getting
rid of a bunch of custom GPIO implementations from the
arch/arm/* tree:
- Move the IOP GPIO driver to the GPIO subsystem and
fix all users to use the gpiolib API for accessing
GPIOs. Delete the old custom GPIO implementation.
- Delete the unused custom PXA GPIO implemention.
- Convert all users of the IXP4 custom GPIO
implementation to use gpiolib and delete the custom
implementation.
- Delete the custom Gemini GPIO implementation, also
completely unused.
- Various cleanups and renamings.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=881E
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"Here is the bulk of GPIO changes for the v3.13 development cycle.
I've got ACKs for the things that affect other subsystems (or it's my
own subsystem, like pinctrl). Most of that pertain to an attempt from
my side to consolidate and get rid of custom GPIO implementations in
the ARM tree. I will continue doing this.
The main change this time is the new GPIO descriptor API, background
for this can be found in Corbet's summary from this january in LWN:
http://lwn.net/Articles/533632/
Summary:
- Merged the GPIO descriptor API from Alexandre Courbot. This is a
first step toward trying to get rid of the global GPIO numberspace
for the future.
- Add an API so that driver can flag that a certain GPIO line is
being used by a irqchip backend for generating IRQs, so that we can
enforce checks, like not allowing users to switch that line to an
output at runtime, since this makes no sense. Implemented
corresponding calls in a few select drivers.
- ACPI GPIO cleanups, refactorings and switch to using the
descriptor-based interface.
- Support for the TPS80036 Palmas GPIO variant.
- A new driver for the Broadcom Kona GPIO SoC IP block.
- Device tree support for the PCF857x driver.
- A set of ARM GPIO refactorings with the goal of getting rid of a
bunch of custom GPIO implementations from the arch/arm/* tree:
* Move the IOP GPIO driver to the GPIO subsystem and fix all users
to use the gpiolib API for accessing GPIOs. Delete the old
custom GPIO implementation.
* Delete the unused custom PXA GPIO implemention.
* Convert all users of the IXP4 custom GPIO implementation to use
gpiolib and delete the custom implementation.
* Delete the custom Gemini GPIO implementation, also completely
unused.
- Various cleanups and renamings"
* tag 'gpio-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (85 commits)
gpio: gpio-mxs: Remove unneeded dt checks
gpio: pl061: don't depend on CONFIG_ARM
gpio: bcm-kona: add missing .owner to struct gpio_chip
gpiolib: provide a declaration of seq_file in gpio/driver.h
gpiolib: include gpio/consumer.h in of_gpio.h for desc_to_gpio()
gpio: provide stubs for devres gpio functions
gpiolib: devres: add missing headers
gpiolib: make GPIO_DEVRES depend on GPIOLIB
gpiolib: devres: fix devm_gpiod_get_index()
gpiolib / ACPI: document the GPIO descriptor based interface
gpiolib / ACPI: allow passing GPIOF_ACTIVE_LOW for GpioInt resources
gpiolib / ACPI: add ACPI support for gpiod_get_index()
gpiolib / ACPI: convert to gpiod interfaces
gpiolib: add gpiod_get() and gpiod_put() functions
gpiolib: port of_ functions to use gpiod
gpiolib: export descriptor-based GPIO interface
Fixup "MAINTAINERS: GPIO-INTEL-MID: add maintainer"
gpio: bcm281xx: Don't print addresses of GPIO area in probe()
gpio: tegra: use new gpio_lock_as_irq() API
gpio: rcar: Include linux/of.h header
...
- Blackfin ADI pin control driver, we move yet another
architecture under this subsystem umbrella.
- Incremental updates to the Renesas Super-H PFC pin control
driver. New subdriver for the r8a7791 SoC.
- Non-linear GPIO ranges from the gpiolib side of things,
this enabled simplified device tree bindings by referring
entire groups of pins on some pin controller to act as
back-end for a certain GPIO-chip driver.
- Add the Abilis TB10x pin control driver used on the ARC
architecture. Also the corresponding GPIO driver is merged
through this tree, so the ARC has full support for pins
and GPIOs after this.
- Subdrivers for Freescale i.MX1, i.MX27 and i.MX50 pin
controller instances. The i.MX1 and i.MX27 is an entirely
new family (silicon) of controllers whereas i.MX50 is
a variant of the previous supported controller.
- Then the usual slew of fixes, cleanups and incremental
updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=z9SM
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Main pin control pull request for the v3.13 cycle.
The changes hitting arch/blackfin are ACKed by the Blackfin
maintainer, and the device tree bindings are ACKed to the extent
possible by someone from the device tree maintainers group.
- Blackfin ADI pin control driver, we move yet another architecture
under this subsystem umbrella.
- Incremental updates to the Renesas Super-H PFC pin control driver.
New subdriver for the r8a7791 SoC.
- Non-linear GPIO ranges from the gpiolib side of things, this
enabled simplified device tree bindings by referring entire groups
of pins on some pin controller to act as back-end for a certain
GPIO-chip driver.
- Add the Abilis TB10x pin control driver used on the ARC
architecture. Also the corresponding GPIO driver is merged through
this tree, so the ARC has full support for pins and GPIOs after
this.
- Subdrivers for Freescale i.MX1, i.MX27 and i.MX50 pin controller
instances. The i.MX1 and i.MX27 is an entirely new family
(silicon) of controllers whereas i.MX50 is a variant of the
previous supported controller.
- Then the usual slew of fixes, cleanups and incremental updates"
The ARC DT changes are apparently still pending, that hopefully gets
sorted out in a timely manner.
* tag 'pinctrl-for-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (48 commits)
pinctrl: imx50: add pinctrl support code for the IMX50 SoC
pinctrl: at91: copy define to driver
pinctrl: remove minor dead code
pinctrl: imx: fix using pin->input_val wrongly
pinctrl: imx1: fix return value check in imx1_pinctrl_core_probe()
gpio: tb10x: fix return value check in tb10x_gpio_probe()
gpio: tb10x: use module_platform_driver to simplify the code
pinctrl: imx27: imx27 pincontrol driver
pinctrl: imx1 core driver
pinctrl: sh-pfc: r8a7791 PFC support
sh-pfc: r8a7778: Add CAN pin groups
gpio: add TB10x GPIO driver
pinctrl: at91: correct a few typos
pinctrl: mvebu: remove redundant of_match_ptr
pinctrl: tb10x: use module_platform_driver to simplify the code
pinctrl: tb10x: fix the error handling in tb10x_pinctrl_probe()
pinctrl: add documentation for pinctrl_get_group_pins()
pinctrl: rockchip: emulate both edge triggered interrupts
pinctrl: rockchip: add rk3188 specifics
pinctrl: rockchip: remove redundant check
...
Add code to support the specific pin arrangements of the Freescale IMX50 SoC.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The #define for the maximum number of GPIO blocks was retrieved
into pinctrl-at91.c by implicit inclusion of <mach/gpio.h>
from <linux/gpio.h> creating a dependency on machine-local
<mach/gpio.h>. Break the depenency by copying this single
define into the driver.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This removes a test whether the 'desc' variable is NULL.
This possibility has already been eliminated by the
below test earlier in the loop:
if (desc == NULL) {
dev_warn(pctldev->dev,
"could not get pin desc for pin %d\n",
pins[i]);
continue;
}
Found with Coverity: CID #1090078
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The commit: "pinctrl: imx: Use struct type for pins" relaced
pin->input_reg by pin->input_val wrongly, fix it at this commit.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In case of error, the function devm_ioremap_nocache() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
imx27 pincontrol driver using the imx1 core driver. The DT bindings are
similar to other imx pincontrol drivers.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core driver for register formats of imx1/imx21/imx27 processors.
The pins of those processors are grouped into ports. Each port has 32
pins. The pins mux configuration is controlled by registers with 1 or 2
bit per pin, depending on the specific control register.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add PFC support for the r8a7791 SoC V2 including pin groups for
on-chip devices such as MSIOF, SCIF, USB, MMC, SDHI, DU.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Kunihito Higashiyama <kunihito.higashiyama.ur@renesas.com>
Signed-off-by: Yoshikazu Fujikawa <yoshikazu.fujikawa.ue@renesas.com>
Signed-off-by: Nobuyuki HIRAI <nobuyuki.hirai.xe@renesas.com>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
[damm@opensource.se: Forward ported to upstream, minor fixes]
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Add CAN data and clock pin groups to R8A7778 PFC driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fix the error handling in tb10x_pinctrl_probe():
- devm_ioremap_resource() return ERR_PTR() and never return NULL
- remove the dev_err call to avoid redundant error message
- pinctrl_register() returns NULL not ERR_PTR()
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Looks like we need a little bit of arch specific handling
with the generic IRQ. Fix the issue with an ifdef the
same way as other drivers do.
ARM needs things set to IRQF_VALID, which also then sets
noprobe. Others seem to use just irq_set_noprobe().
Otherwise we can get:
drivers/pinctrl/pinctrl-single.c: In function 'pcs_irqdomain_map':
drivers/pinctrl/pinctrl-single.c:1750:2: error: implicit declaration of function 'set_irq_flags' [-Werror=implicit-function-declaration]
drivers/pinctrl/pinctrl-single.c:1750:21: error: 'IRQF_VALID' undeclared (first use in this function)
drivers/pinctrl/pinctrl-single.c:1750:34: error: 'IRQF_PROBE' undeclared (first use in this function)
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The gpio interrupt controller on Rockchip socs can do edge triggers only
for single edges but not both. Nevertheless a lot of gpio users rely on
the availability of both-edge triggered interrupts - i.e. gpio-keys.
Therefore implement a solution similar to pinctrl-coh901 re-setting the
triggering edge depending on the gpio value in the interrupt demuxer.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Besides the pull registers sitting in a separate place, the rk3188 also
has the peculiarity that the pull registers of the first bank are split
and the first half is sitting in the register space of the pmu.
Therefore this adds a special bank-type for the first bank, to handle
the two register sources.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The check limiting bias options to supported ones is already
done thru rockchip_pinconf_pull_valid. Therefore this check is
redundant and can be removed.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are Rockchip SoCs, namely the rk3188, that combine a set of
regular banks with banks that need special handling for some settings.
Therefore add the possibility for the driver to handle more than one
bank type.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Further investigation of the different Rockchip SoCs showed that
the differences especially in the pull settings are quite deep.
As further patches will show, the register layout for the pulls of
the rk3188 is quite strange. Also it is to assume, that later
Rockchip SoCs may introduce even more quirks in this regard, making
it hard to support all of those using the current generic pull_*
variables.
Therefore move the driver to hold the type of controller in an enum
and do the handling according to it in the necessary places. Also
instead of calculating the register in the get and set pull functions
move it to a type-specific callback.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This fixes a typo which left twsi config3 option enabled.
Cc: stable@vger.kernel.org
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinmux driver of the Abilis Systems TB10x platform based on ARC700 CPUs.
Used to control the pinmux and is a prerequisite for the GPIO driver.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Pierrick Hascoet <pierrick.hascoet@abilis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds the infrastructure required to register non-linear gpio
ranges through gpiolib and the standard GPIO device tree bindings.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When an IRQ is started on a GPIO line, mark this GPIO as IRQ in
the gpiolib so we can keep track of the usage centrally.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When an IRQ is started on a GPIO line, mark this GPIO as IRQ in
the gpiolib so we can keep track of the usage centrally.
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For omaps, we still have dependencies to the legacy code
for handling the PRM (Power Reset Management) interrupts,
and also for reconfiguring the io wake-up chain after
changes.
Let's pass the PRM interrupt and the rearm functions via
auxdata. Then when at some point we have a proper PRM
driver, we can get the interrupt via device tree and
set up the rearm function as exported function in the
PRM driver.
By using auxdata we can remove a dependency to the
wake-up events for converting omap3 to be device
tree only.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Prakash Manjunathappa <prakash.pm@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The pin control registers can have interrupts for example
for device wake-up. These interrupts can be treated as a
chained interrupt controller as suggested earlier by
Linus Walleij <linus.walleij@linaro.org>.
This patch adds support for interrupts in a way that
should be pretty generic, and works for the omaps that
support wake-up interrupts. On omaps, there's an
interrupt enable and interrupt status bit for each pin.
The two pinctrl domains on omaps share a single interrupt
from the PRM chained interrupt handler. Support for
other similar hardware should be easy to add.
Note that this patch does not attempt to handle the
wake-up interrupts automatically unlike the earlier
patches. This patch allows the device drivers to do
a request_irq() on the wake-up pins as needed. I'll
try to do also a separate generic patch for handling
the wake-up events automatically.
Also note that as this patch makes the pinctrl-single
an irq controller, the current bindings need some
extra trickery to use interrupts from two different
interrupt controllers for the same driver. So it
might be worth waiting a little on the patches
enabling the wake-up interrupts from drivers as there
should be a generic way to handle it coming. And also
there's been discussion of interrupts-extended binding
for using interrupts from multiple interrupt controllers.
In any case, this patch should be ready to go allowing
handling the wake-up interrupts in a generic way, or
separately from the device drivers.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Prakash Manjunathappa <prakash.pm@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: linux-kernel@vger.kernel.org
Cc: Benoît Cousson <bcousson@baylibre.com>
Cc: devicetree@vger.kernel.org
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The AS3722 is a compact system PMU suitable for mobile phones, tablets etc.
Add a driver to support accessing the GPIO, pinmux and pin configuration
of 8 GPIO pins found on the ams AS3722 through pin control driver and
gpiolib.
The driver will register itself as the pincontrol driver and gpio driver.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Let's replace is_pinconf with flags and add struct pcs_soc_data
so we can support SoC specific features like pin wake-up events.
Done in collaboration with Roger Quadros <rogerq@ti.com>.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Prakash Manjunathappa <prakash.pm@ti.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO output value should be set after the GPIO interrupt is disabled.
Use BIT macro as well.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
[Edited commit message]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Also avoid use NULL pointer in error message.
v2-changes:
- use port pinter only after checking
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Palmas devices do not support the default bias configuration
and hence removing this option from valid pin config parameters.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
dn and dp of USB1 can share with UART1(UART1 can route rx,tx to dn and dp pins of USB1).
here we add this pinmux capability.
USB1/UART1 mode selection has dedicated control register in RSC module, here we attach
the register offset of private data of related pin groups.
Signed-off-by: Rong Wang <Rong.Wang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
USP(Universal Serial Ports) can be UART as commit 5df831117b,
this patch defines the USP-based UART function pin groups for prima2.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
the old codes defined uart0_nostreamctrl_pins, but missed pingroup
and padmux definition for it. this patch fixes it.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Recent movement of all configurations of pin in the single call of
pin_config_set(), it is aborting configuration if BIAS_PULL_PIN_DEFAULT
is selected as return of configuration.
The original idea was to just avoid any update on register for pull up/down
configuration if this option is selected.
Fixing this by just bypassing any register update for BIAS_PULL_PIN_DEFAULT
and continuing the remaining configuration.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Palmas pinmux and pin configuration support the single pin level
configuration in place of pin group.
Hence it is only require to pin_config_{set|get} and do not require
pin_config_group_{set|get}. As core framework already check for
require APIs availability, it is not require to implement as dummy
for non-require ops and so removing it.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Values of pins in table s5pv210 bank are incorrect. This patch correct values.
Signed-off-by: Mateusz Krawczuk <m.krawczuk@partner.samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Current code hold port->lock spinlock and then try to grab the lock again
in adi_gpio_set_value(). Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace at91_mux_get_deglitch with at91_mux_pio3_get_deglitch when using
sam9x5 (pio3) IP.
at91_mux_get_deglitch only test the activation of the "Input Filter" which
may be overloaded by the activation of the "Input Filter Slow Clock" to use
the input filter as a debounce filter instead of a deglitch filter.
Fix at91_mux_pio3_get_debounce to test the activation of the Input Filter
before testing the activation of the debounce filter (Input Filter Slow
Clock depends on Input Filter).
Fix at91_mux_pio3_set_debounce function to avoid disabling the deglitch
filter ("Input Filter") when debounce filter is disabled.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are four I2C interfaces on r8a7790, each of them can be connected to
one of the two respective I2C controllers, e.g. interface #0 can be
configured to work with I2C0 or with IIC0. Additionally some of those
interfaces can also use one of several pin sets. Interface #3 is special,
because it can be used in automatic mode for DVFS. It only has one set
of pins available and those pins cannot be used for anything else, they
also lack the GPIO function.
This patch uses the sh-pfc ability to configure pins, not associated with
GPIOs and adds support for I2C3 to the r8a7790 PFC set up.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Adds pinmux for i2c bus 1 and 2. (Pins for 0 and 3 are not multiplexed.)
Signed-off-by: Ulrich Hecht <ulrich.hecht@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
sizeof() is already size_t so there is no need to cast here. Generally,
casting inside the min() macro instead of using min_t() is considered
bad style.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Have pinconf_dbg_config_write() return a ssize_t. This fixes the following
compilation warning:
drivers/pinctrl/pinconf.c:617:2: warning: initialization from incompatible pointer type [enabled by default]
drivers/pinctrl/pinconf.c:617:2: warning: (near initialization for ‘pinconf_dbg_pinconfig_fops.write’) [enabled by default]
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Stanislaw Gruszka