In special conditions where a subchannel rejects the HALT I/O-
instruction with a busy indication (cc 2), I/O may stall.
I/O request termination logic retries HALT I/O indefinitely
because it expects HALT I/O to alter the subchannel status which
is not true when cc 2 is returned.
In case of a busy indication, try CLEAR I/O instruction immediately.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
1. Multipath devices for which SetPGID is not supported are not handled well.
Use NOP ccws for path verification (sans path grouping) when SetPGID is not
supported.
2. Check for PGIDs already set with SensePGID on _all_ paths (not just the
first one) and try to find a common one. Moan if no common PGID can be
found (and use NOP verification). If no PGIDs have been set, use the css
global PGID (as before). (Rationale: SetPGID will get a command reject if
the PGID it tries to set does not match the already set PGID.)
3. Immediately before reboot, issue RESET CHANNEL PATH (rcp) on all chpids. This
will remove the old PGIDs. rcp will generate solicited CRWs which can be
savely ignored by the machine check handler (all other actions create
unsolicited CRWs).
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fixes for several channel measurement facility bugs:
* Blocks copied from the hardware might not be consistent. Solve this
by moving the copying into idle state and repeating the copying.
* avg_sample_interval changed with every read, even though no new block
was available. Solve this by storing a timestamp when the last new
block was received.
* Several locking issues.
* Measurements were not reenabled after a disconnected device became
available again.
* Remove #defines for ioctls that were never implemented.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After setting a path to a dasd offline at the SE, I/O hangs on that
dasd for 5 minutes, then continues.
I/O for which an interrupt will not be reported after the channel
path has been disabled was not terminated by the common I/O layer,
causing the dasd MIH to hit after 5 minutes.
Be more aggressive in terminating I/O after setting a channel path
offline. Also make sure to generate a fake irb if the device
driver issues an I/O request after being notified of the killed
I/O and clear residual information from the irb before trying to
start the delayed verification.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When cio waits for the interrupt for a basic sense, interrupts for hsch() or
csch() issued in the meantime are wrongly counted as interrupts for the basic
sense and the accumulated irb is passed to the device driver. In
ccw_device_w4sense(), check for clear or halt function in the irb and pass the
irb for the csch() or hsch() to the device driver.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for multiple subchannel sets. Works with arbitrary devices in
subchannel set 1 and is transparent to device drivers. Although currently
only two subchannel sets are available, this will work with the architectured
maximum number of subchannel sets as well.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch introduces a struct subchannel_id containing the subchannel number
(formerly referred to as "irq") and switches code formerly relying on the
subchannel number over to it.
While we're touching inline assemblies anyway, make sure they have correct
memory constraints.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Common i/o layer changes:
- Collect the irb at the correct subchannel when waiting for the clear
interrupt during subchannel cleaning befor reIPL - don't stop at the first
interrupt that comes in.
- Change "extern __inline__" to "static inline".
- Remove unneeded qdio includes.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Close a small window where a device may be not operational again after senseid
finished and the "same device" check fails due to dev=0000 by checking for dnv
after stsch() by then setting the device to not operational. (No need to
check for dnv in ccw_device_handle_oper() again since we don't do stsch() into
the subchannel's schib in the meantime and will get a crw anyway if the device
becomes not oper again).
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Peter Oberparleiter