P2040RDB Specification:
-----------------------
2Gbyte unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
128 Mbyte NOR flash single-chip memory
256 Kbit M24256 I2C EEPROM
16 Mbyte SPI memory
SD connector to interface with the SD memory card
dTSEC1: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC2: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC3: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC4: connected to the Vitesse RGMII PHY (VSC8641)
dTSEC5: connected to the Vitesse RGMII PHY (VSC8641)
I2C1: Real time clock, Temperature sensor
I2C2: Vcore Regulator, 256Kbit I2C Bus EEPROM
SATA: Lanes C and Land D of Bank2 are connected to two SATA connectors
UART: supports two UARTs up to 115200 bps for console
USB 2.0: connected via a internal UTMI PHY to two TYPE-A interfaces
PCIe:
- Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT1
- Lanes C and Land D of Bank2 are connected to one x4 PCIe SLOT2
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
GPIO drivers are getting consolidated into drivers/gpio. While at it,
change the driver name to mpc5200-gpio* to avoid collisions.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The free_initmem function is basically duplicated in mm/init_32,
and init_64, and is moved to the common 32/64-bit mm/mem.c.
All other sections except init were removed in v2.6.15 by
6c45ab992e (powerpc: Remove section
free() and linker script bits), and therefore the bulk of the executed
code is identical.
This patch also removes updating ppc_md.progress to NULL in the powermac
late_initcall.
Suggested-by: Milton Miller <miltonm@bga.com>
Suggested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Carroll <dcarroll@astekcorp.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On pseries machines, consoles are provided by the hypervisor using
a low level get_chars/put_chars type interface. However, this is
really just a transport to the service processor which implements
them either as "raw" console (networked consoles, HMC, ...) or as
"hvsi" serial ports.
The later is a simple packet protocol on top of the raw character
interface that is supposed to convey additional "serial port" style
semantics. In practice however, all it does is provide a way to
read the CD line and set/clear our DTR line, that's it.
We currently implement the "raw" protocol as an hvc console backend
(/dev/hvcN) and the "hvsi" protocol using a separate tty driver
(/dev/hvsi0).
However this is quite impractical. The arbitrary difference between
the two type of devices has been a major source of user (and distro)
confusion. Additionally, there's an additional mini -hvsi implementation
in the pseries platform code for our low level debug console and early
boot kernel messages, which means code duplication, though that low
level variant is impractical as it's incapable of doing the initial
protocol negociation to establish the link to the FSP.
This essentially replaces the dedicated hvsi driver and the platform
udbg code completely by extending the existing hvc_vio backend used
in "raw" mode so that:
- It now supports HVSI as well
- We add support for hvc backend providing tiocm{get,set}
- It also provides a udbg interface for early debug and boot console
This is overall less code, though this will only be obvious once we
remove the old "hvsi" driver, which is still available for now. When
the old driver is enabled, the new code still kicks in for the low
level udbg console, replacing the old mini implementation in the platform
code, it just doesn't provide the higher level "hvc" interface.
In addition to producing generally simler code, this has several benefits
over our current situation:
- The user/distro only has to deal with /dev/hvcN for the hypervisor
console, avoiding all sort of confusion that has plagued us in the past
- The tty, kernel and low level debug console all use the same code
base which supports the full protocol establishment process, thus the
console is now available much earlier than it used to be with the
old HVSI driver. The kernel console works much earlier and udbg is
available much earlier too. Hackers can enable a hard coded very-early
debug console as well that works with HVSI (previously that was only
supported for the "raw" mode).
I've tried to keep the same semantics as hvsi relative to how I react
to things like CD changes, with some subtle differences though:
- I clear DTR on close if HUPCL is set
- Current hvsi triggers a hangup if it detects a up->down transition
on CD (you can still open a console with CD down). My new implementation
triggers a hangup if the link to the FSP is severed, and severs it upon
detecting a up->down transition on CD.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When CONFIG_PPC_EARLY_DEBUG is set, call register_early_udbg_console()
early from generic code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently Maple setup code creates cpc925_edac device only on
Motorola ATCA-6101 blade. Make setup code check bridge revision
and enable EDAC on all U3H bridges.
Verified on Momentum MapleD (ppc970fx kit) board.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reconfiguration notifier call for device node may fail by several reasons,
but it always assumes kmalloc failures.
This enables reconfiguration notifier call chain to get the actual error
code rather than -ENOMEM by converting all reconfiguration notifier calls
to return encapsulate error code with notifier_from_errno().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This introduces pSeries_reconfig_notify() as a just wrapper of
blocking_notifier_call_chain() for pSeries_reconfig_chain.
This is a preparation to improvement of error code on reconfiguration
notifier failure.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The Freescale hypervisor does not allow guests to write to the timebase
registers (virtualizing the timebase register was deemed too complicated),
so don't try to synchronize the timebase registers when we're running
under the hypervisor.
This typically happens when kexec support is enabled.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1010RDB Overview
-----------------
1Gbyte DDR3 (on board DDR)
32Mbyte 16bit NOR flash
32Mbyte SLC NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
I2C Board 128x8 bit memory
SD/MMC connector to interface with the SD memory card
2 SATA interface
1 internal SATA connect to 2.5. 160G SATA2 HDD
1 eSATA connector to rear panel
USB 2.0
x1 USB 2.0 port: connected via a UTMI PHY to Mini-AB interface.
x1 USB 2.0 port: directly connected to Mini-AB interface Ethernet
eTSEC1: Connected to RGMII PHY VSC8641XKO
eTSEC2: Connected to SGMII PHY VSC8221
eTSEC3: Connected to SGMII PHY VSC8221 eCAN
Two DB-9 female connectors for Field bus interface UART
DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
mpc8610hpcd_set_pixel_clock() calculates the correct value of the PXCLK
bits in the CLKDVDR register for a given pixel clock rate. The code which
performs this calculation is overly complicated and includes an error
estimation routine that doesn't work most of the time anyway. Replace the
code with the simpler routine that's currently used on the P1022DS.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
To ensure that the DIU pixel clock will not be set to an invalid value,
clamp the PXCLK divider to the allowed range (2-255). This also acts as
a limiter for the pixel clock.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
e500mc cannot doze or nap due to an erratum (as well as having a
different mechanism than previous e500), but it has a "wait" instruction
that is similar to doze.
On 64-bit, due to the soft-irq-disable mechanism, the existing
book3e_idle should be used instead.
Signed-off-by: Vakul Garg <vakul@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The platform file for the Freecale P1022DS reference board is not freeing
the ioremap() mapping of the PIXIS and global utilities nodes it creates.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for the ePAPR-compliant Freescale hypervisor (aka "Topaz") on
the Freescale P3041DS, P4080DS, and P5020DS reference boards.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale ePAPR reference hypervisor provides interrupt controller
services via a hypercall interface, instead of emulating the MPIC
controller. This is called the VMPIC.
The ePAPR "virtual interrupt controller" provides interrupt controller
services for external interrupts. External interrupts received by a
partition can come from two sources:
- Hardware interrupts - hardware interrupts come from external
interrupt lines or on-chip I/O devices.
- Virtual interrupts - virtual interrupts are generated by the hypervisor
as part of some hypervisor service or hypervisor-created virtual device.
Both types of interrupts are processed using the same programming model and
same set of hypercalls.
Signed-off-by: Ashish Kalra <ashish.kalra@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P1023 processor is an e500v2 based SoC that utilizes the DPAA
networking architecture. This adds basic board support for non-DPAA
functionality (device tree, board file, etc).
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In cases like when the platform is used under hypervisor we will NOT
have an MPIC controller but still want doorbells setup.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Several changes on PCIe support on P3041DS/P4080DS/P5020DS boards:
* Add support for "fsl,qoriq-pcie-v2.2" needed by P3041 & P5020
* Removed support for setting primary_phb_addr as we have no ISA need
* Add PCI controller to of_platform_bus_probe (for EDAC)
* Cleanup building w/SWIOTLB off on P4080DS (not stricly PCIe related)
Signed-off-by: Kai.Jiang <Kai.Jiang@freescale.com>
Signed-off-by: Laurentiu TUDOR <Laurentiu.Tudor@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Many stupid corrections of duplicated includes based on the output of
scripts/checkincludes.pl.
Signed-off-by: Vitaliy Ivanov <vitalivanov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On many platforms (including pSeries), smp_ops->message_pass is always
smp_muxed_ipi_message_pass. This changes arch/powerpc/kernel/smp.c so
that if smp_ops->message_pass is NULL, it calls smp_muxed_ipi_message_pass
directly.
This means that a platform doesn't need to set both .message_pass and
.cause_ipi, only one of them. It is a slight performance improvement
in that it gets rid of an indirect function call at the expense of a
predictable conditional branch.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Lenghty lists of the kind "depends on ARCH1 || ARCH2 ... || ARCH123" are
usually either wrong or too coarse grained. Or plain an ugly sin.
[ tglx: Fixed up amigaone ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linux-alpha@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Gerhard Pircher <gerhard_pircher@gmx.net>
Link: http://lkml.kernel.org/r/20110601180610.984881988@duck.linux-mips.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
powerpc has two different ways of matching PCI devices to their
corresponding OF node (if any) for historical reasons. The ppc64 one
does a scan looking for matching bus/dev/fn, while the ppc32 one does a
scan looking only for matching dev/fn on each level in order to be
agnostic to busses being renumbered (which Linux does on some
platforms).
This removes both and instead moves the matching code to the PCI core
itself. It's the most logical place to do it: when a pci_dev is created,
we know the parent and thus can do a single level scan for the matching
device_node (if any).
The benefit is that all archs now get the matching for free. There's one
hook the arch might want to provide to match a PHB bus to its device
node. A default weak implementation is provided that looks for the
parent device device node, but it's not entirely reliable on powerpc for
various reasons so powerpc provides its own.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Michal Simek <monstr@monstr.eu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The Apple custom PIC only exist in some earlier machine models,
anything with an MPIC will crash on suspend if we register those
syscore ops unconditionally.
This is a regression caused by commit f5a592f7d7 ("PM / PowerPC: Use
struct syscore_ops instead of sysdevs for PM")
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds MSI support for 440SPe, 460Ex, 460Sx and 405Ex.
Signed-off-by: Rupjyoti Sarmah <rsarmah@apm.com>
Signed-off-by: Tirumala R Marri <tmarri@apm.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Rename functions and arguments to reflect current usage. iic_cause_ipi
becomes iic_message_pass and iic_ipi_to_irq becomes iic_msg_to_irq,
and iic_request_ipi now takes a message (msg) instead of an ipi number.
Also mesg is renamed to msg.
Commit f1072939b6 (powerpc: Remove checks for MSG_ALL and
MSG_ALL_BUT_SELF) connected the smp_message_pass hook for cell to the
underlying iic_cause_IPI, a platform unique name. Later 23d72bfd8f
(powerpc: Consolidate ipi message mux and demux) added a cause_ipi
hook to the smp_ops, also used in message passing, but for controllers
that can not send 4 unique messages and require multiplexing. It is
even more confusing that the both take two arguments, but one is the
small message ordinal and the other is an opaque long data associated
with the cpu.
Since cell iic maps messages one to one to ipi irqs, rename the
function and argument to translate from ipi to message. Also make it
clear that iic_request_ipi takes a message number as the argument
for which ipi to create and request.
No functionional change, just renames to avoid future confusion.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The cell iic interrupt controller has enough software caused interrupts
to use a unique interrupt for each of the 4 messages powerpc uses.
This means each interrupt gets its own irq action/data combination.
Use the seperate, optimized, arch common ipi action functions
registered via the helper smp_request_message_ipi instead passing the
message as action data to a single action that then demultipexes to
the required acton via a switch statement.
smp_request_message_ipi will register the action as IRQF_PER_CPU
and IRQF_DISABLED, and WARN if the allocation fails for some reason,
so no need to print on that failure. It will return positive if
the message will not be used by the kernel, in which case we can
free the virq.
In addition to elimiating inefficient code, this also corrects the
error that a kernel built with kexec but without a debugger would
not register the ipi for kdump to notify the other cpus of a crash.
This also restores the debugger action to be static to kernel/smp.c.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Manual merge of arch/powerpc/kernel/smp.c and add missing scheduler_ipi()
call to arch/powerpc/platforms/cell/interrupt.c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6: (34 commits)
PM: Introduce generic prepare and complete callbacks for subsystems
PM: Allow drivers to allocate memory from .prepare() callbacks safely
PM: Remove CONFIG_PM_VERBOSE
Revert "PM / Hibernate: Reduce autotuned default image size"
PM / Hibernate: Add sysfs knob to control size of memory for drivers
PM / Wakeup: Remove useless synchronize_rcu() call
kmod: always provide usermodehelper_disable()
PM / ACPI: Remove acpi_sleep=s4_nonvs
PM / Wakeup: Fix build warning related to the "wakeup" sysfs file
PM: Print a warning if firmware is requested when tasks are frozen
PM / Runtime: Rework runtime PM handling during driver removal
Freezer: Use SMP barriers
PM / Suspend: Do not ignore error codes returned by suspend_enter()
PM: Fix build issue in clock_ops.c for CONFIG_PM_RUNTIME unset
PM: Revert "driver core: platform_bus: allow runtime override of dev_pm_ops"
OMAP1 / PM: Use generic clock manipulation routines for runtime PM
PM: Remove sysdev suspend, resume and shutdown operations
PM / PowerPC: Use struct syscore_ops instead of sysdevs for PM
PM / UNICORE32: Use struct syscore_ops instead of sysdevs for PM
PM / AVR32: Use struct syscore_ops instead of sysdevs for PM
...
When using a property refering to the availibily of dynamic dma windows
call it ddw_avail not ddr_avail.
dupe_ddw_if_already_created does not dupilcate anything, it only finds
and reuses the windows we already created, so rename it to
find_existing_ddw. Also, it does not need the pci device node, so
remove that argument.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Move the discovery of windows previously setup from when the pci driver
calls set_dma_mask to an arch_initcall.
When kexecing into a kernel with dynamic dma windows allocated, we need
to find the windows early so that memory hot remove will be able to
delete the tces mapping the to be removed memory and memory hotplug add
will map the new memory into the window. We should not wait for the
driver to be loaded and the device to be probed. The iommu init hooks
are before kmalloc is setup, so defer to arch_initcall.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we destroy the window, we need to remove the property recording that
we setup the window. Otherwise the next kernel we kexec will be
confused.
Also we should remove the property if even if we don't find the
ibm,ddw-applicable window or if one of the property sizes is unexpected;
presumably these came from a prior kernel via kexec, and we will not be
maintaining the window with respect to memory hotplug.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Do not check dma supported until we have chosen the right dma ops.
Check that the device is pci before treating it as such.
Check the mask is supported by the selected dma ops before
committing it.
We only need to set iommu ops if it is not the current ops; this
avoids searching the tree for the iommu table unnecessarily.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Otherwise we get silent truncations.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Milton Miller <miltonm@bga.com>
Cc: linuxppc-dev@ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If the video mode is set to 16-, 24-, or 32-bit pixels, then the pixel data
contains actual levels of red, blue, and green. However, if the video mode
is set to 8-bit pixels, then the 8-bit value represents an index into color
table. This is called "palette mode" on the Freescale DIU video controller.
The DIU driver does not currently support palette mode, but the MPC8610 HPCD
board file returned a non-zero (although incorrect) pixel format value for
8-bit mode.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It may trigger a warning in fs/proc/generic.c:__xlate_proc_name() when
trying to add an entry for the interrupt handler to sysfs.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Instead of checking for rogue msi numbers via the irq_map host field
set the chip_data to h.host_data (which is the msic struct pointer)
at map and compare it in get_irq.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Building on Grant's efforts to remove the irq_map array, this patch
moves spider-pics use of virq_to_host() to use irq_data_get_chip_data
and sets the irq chip data in the map call, like most other interrupt
controllers in powerpc.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It was called from irq_create_mapping if that was called for a host
and hwirq that was previously mapped, "to update the flags". But the
only implementation was in beat_interrupt and all it did was repeat a
hypervisor call without error checking that was performed with error
checking at the beginning of the map hook. In addition, the comment on
the beat remap hook says it will only called once for a given mapping,
which would apply to map not remap.
All flags should be known by the time the match hook is called, before
we call the map hook. Removing this mostly unused hook will simpify
the requirements of irq_domain concept.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Create a dummy irq_host using the generic dummy irq chip for the secondary
cpus to use. Create a direct irq mapping for the ipi and register the
ipi action handler against it. If for some unlikely reason part of this
fails then don't detect the secondary cpus.
This removes another instance of NO_IRQ_IGNORE, records the ipi stats
for the secondary cpus, and runs the ipi on the interrupt stack.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If none of irq category bits were set mpc52xx_get_irq() would pass
NO_IRQ_IGNORE (-1) to irq_linear_revmap, which does an unsigned compare
and declares the interrupt above the linear map range. It then punts
to irq_find_mapping, which performs a linear search of all irqs,
which will likely miss and only then return NO_IRQ.
If no status bit is set, then we should return NO_IRQ directly.
The interrupt should not be suppressed from spurious counting, in fact
that is the definition of supurious.
Signed-off-by: Milton Miller <miltonm@bga.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As NO_IRQ_IGNORE is only used between the static function cpld_pic_get_irq
and its caller cpld_pic_cascade, and cpld_pic_cascade only uses it to
suppress calling handle_generic_irq, we can change these uses to NO_IRQ
and remove the extra tests and pathlength in cpld_pic_cascade.
Signed-off-by: Milton Miller <miltonm@bga.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These all just clear chip or chipdata fields, which will be done
by the generic code when we call irq_free_descs.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Compile the new smp ipi mux and demux code only if a platform
will make use of it. The new config is selected as required.
The new cause_ipi smp op is only available conditionally to point out
configs where the select is required; this makes setting the op an
immediate fail instead of a deferred unresolved symbol at link.
This also creates a new config for power surge powermac upgrade support
that can be disabled in expert mode but is default on.
I also removed the depends / default y on CONFIG_XICS since it is selected
by PSERIES.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Consolidate the mux and demux of ipi messages into smp.c and call
a new smp_ops callback to actually trigger the ipi.
The powerpc architecture code is optimised for having 4 distinct
ipi triggers, which are mapped to 4 distinct messages (ipi many, ipi
single, scheduler ipi, and enter debugger). However, several interrupt
controllers only provide a single software triggered interrupt that
can be delivered to each cpu. To resolve this limitation, each smp_ops
implementation created a per-cpu variable that is manipulated with atomic
bitops. Since these lines will be contended they are optimialy marked as
shared_aligned and take a full cache line for each cpu. Distro kernels
may have 2 or 3 of these in their config, each taking per-cpu space
even though at most one will be in use.
This consolidation removes smp_message_recv and replaces the single call
actions cases with direct calls from the common message recognition loop.
The complicated debugger ipi case with its muxed crash handling code is
moved to debug_ipi_action which is now called from the demux code (instead
of the multi-message action calling smp_message_recv).
I put a call to reschedule_action to increase the likelyhood of correctly
merging the anticipated scheduler_ipi() hook coming from the scheduler
tree; that single required call can be inlined later.
The actual message decode is a copy of the old pseries xics code with its
memory barriers and cache line spacing, augmented with a per-cpu unsigned
long based on the book-e doorbell code. The optional data is set via a
callback from the implementation and is passed to the new cause-ipi hook
along with the logical cpu number. While currently only the doorbell
implemntation uses this data it should be almost zero cost to retrieve and
pass it -- it adds a single register load for the argument from the same
cache line to which we just completed a store and the register is dead
on return from the call. I extended the data element from unsigned int
to unsigned long in case some other code wanted to associate a pointer.
The doorbell check_self is replaced by a call to smp_muxed_ipi_resend,
conditioned on the CPU_DBELL feature. The ifdef guard could be relaxed
to CONFIG_SMP but I left it with BOOKE for now.
Also, the doorbell interrupt vector for book-e was not calling irq_enter
and irq_exit, which throws off cpu accounting and causes code to not
realize it is running in interrupt context. Add the missing calls.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I have no idea if the beat hypervisor supports multiple cpus in
a partition, but the code has not been touched since these stubs
were added in February of 2007 except to move them in April of 2008.
These are stubs: start_cpu always returns fail (which is dropped),
the message passing and reciving are empty functions, and the top
of file comment says "Incomplete".
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Replace all remaining callers of alloc_maybe_bootmem with
zalloc_maybe_bootmem. The callsite in pci_dn is followed with a
memset to clear the memory, and not zeroing at the other callsites
in the celleb fake pci code could lead to following uninitialized
memory as pointers or even freeing said pointers on error paths.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Its unused, and of the three declarations, one is duplicated in pmac.h,
the second is static and the third is renamed and static.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now that smp_ops->smp_message_pass is always called with an (online) cpu
number for the target remove the checks for MSG_ALL and MSG_ALL_BUT_SELF.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now that we never set a cpu above nr_cpu_ids possible we can
limit our initial paca allocation to nr_cpu_ids. We can then
clamp the number of cpus in platforms/iseries/setup.c.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
9cb82f2f46 (Make iSeries spin on
__secondary_hold_spinloop, like pSeries) added a load of current_set
but this load was repeated later and we don't even have the paca yet.
It also checked __secondary_hold_spinloop with a 32 bit compare instead
of a 64 bit compare.
b6f6b98a4e (Don't spin on sync instruction
at boot time) missed the copy of the startup code in iseries.
1426d5a3bd (Dynamically allocate pacas)
doesn't allow for pacas to be less than lppacas and recalculated the paca
location from the cpu id in r0 every time through the secondary loop.
Various revisions over time made the comments on conditional branches
confusing with respect to being a hold loop or forward progress
Mostly in-order description of the changes:
Replicate the few lines of code saved by the ugly scoped ifdef CONFIG_SMP
in the secondary loop between yielding on UP and marking time with the
hypervisor on SMP. Always compile the iseries_secondary_yield loop and
use it if the cpu id is above nr_cpu_ids. Change all forward progress
paths to be forward branches to the next numerical label. Assign a
label to all loops. Move all sync instructions from the loops to the
forward progress path. Wait to load current_set until paca is set to go.
Move the iseries_secondary_smp_loop label to cover the whole spin loop.
Add HMT_MEDIUM when we make forward progress.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I have a report of an FWNMI with an r3 value that we think is
corrupt, but since we don't print r3 we have no idea what was
wrong with it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we swtich to direct dma ops, we set the dma data union to have the
dma offset. When we switch back to iommu table ops because of a later
dma_set_mask, we need to restore the iommu table pointer. Without this
change, crashes have been observed on kexec where (for reasons still
being investigated) we fall back to a 32-bit dma mask on a particular
device and then panic because the table pointer is not valid.
The easiset way to find this value is to call
pci_dma_dev_setup_pSeriesLP which will search up the pci tree until it
finds the node with the table.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Milton Miller <miltonm@bga.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have a confusing number of ioremap functions. Make things just a
bit simpler by merging ioremap_flags and ioremap_prot.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Future releases of fimrware will enforce a requirement that DTL buffers
do not cross a 4k boundary. Commit
127493d5dc satisfies this requirement for
CONFIG_VIRT_CPU_ACCOUNTING=y kernels, but if !CONFIG_VIRT_CPU_ACCOUNTING
&& CONFIG_DTL=y, the current code will fail at dtl registration time.
Fix this by making the kmem cache from
127493d5dc visible outside of setup.c and
using the same cache in both dtl.c and setup.c. This requires a bit of
reorganization to ensure ordering of the kmem cache and buffer
allocations.
Note: Since firmware now limits the size of the buffer, I made
dtl_buf_entries read-only in debugfs.
Tested with upcoming firmware with the 4 combinations of
CONFIG_VIRT_CPU_ACCOUNTING and CONFIG_DTL.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we kexec we look for a particular property added by the first
kernel, "linux,direct64-ddr-window-info", per-device where we already
have set up dynamic dma windows. The current code, though, wasn't
initializing the size of this property and thus when we kexec'd, we
would find the property but read uninitialized memory resulting in
garbage ddw values for the kexec'd kernel and panics. Fix this by
setting the size at enable_ddw() time and ensuring that the size of the
found property is valid at dupe_ddw_if_kexec() time.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit b826291c, "drivercore/dt: add a match table pointer to struct
device" added an of_match pointer to struct device to cache the
of_match_table entry discovered at driver match time. This was unsafe
because matching is not an atomic operation with probing a driver. If
two or more drivers are attempted to be matched to a driver at the
same time, then the cached matching entry pointer could get
overwritten.
This patch reverts the of_match cache pointer and reworks all users to
call of_match_device() directly instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Make some PowerPC architecture's code use struct syscore_ops
objects for power management instead of sysdev classes and sysdevs.
This simplifies the code and reduces the kernel's memory footprint.
It also is necessary for removing sysdevs from the kernel entirely in
the future.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a platform for the Wire Speed Processor, based on the PPC A2.
This includes code for the ICS & OPB interrupt controllers, as well
as a SCOM backend, and SCOM based cpu bringup.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jack Miller <jack@codezen.org>
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For adapters which have devices under a PCIe switch/bridge it is informative
to display information for both the PCIe switch/bridge and the device on
which the bus error was detected.
rebased to powerpc-next
Signed-off-by: Richard A Lary <rlary@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds support for handling IO Event interrupts which come
through at the /event-sources/ibm,io-events device tree node.
The interrupts come through ibm,io-events device tree node are generated
by the firmware to report IO events. The firmware uses the same interrupt
to report multiple types of events for multiple devices. Each device may
have its own event handler. This patch implements a plateform interrupt
handler that is triggered by the IO event interrupts come through
ibm,io-events device tree node, pull in the IO events from RTAS and call
device event handlers registered in the notifier list.
Device event handlers are expected to use atomic_notifier_chain_register()
and atomic_notifier_chain_unregister() to register/unregister their
event handler in pseries_ioei_notifier_list list with IO event interrupt.
Device event handlers are responsible to identify if the event belongs
to the device event handler. The device event handle should return NOTIFY_OK
after the event is handled if the event belongs to the device event handler,
or NOTIFY_DONE otherwise.
Signed-off-by: Tseng-Hui (Frank) Lin <thlin@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fundamental reset is an optional reset type supported only by PCIe adapters.
Handle the unexpected case where a non-PCIe device has requested a
fundamental reset. Try hot-reset as a fallback to handle this case.
Signed-off-by: Richard A Lary <rlary@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For multifunction adapters with a PCI bridge or switch as the device
at the Partitionable Endpoint(PE), if one or more devices below PE
sets dev->needs_freset, that value will be set for the PE device.
In other words, if any device below PE requires a fundamental reset
the PE will request a fundamental reset.
Signed-off-by: Richard A Lary <rlary@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Adds support for page coalescing, which is a feature on IBM Power servers
which allows for coalescing identical pages between logical partitions.
Hint text pages as coalesce candidates, since they are the most likely
pages to be able to be coalesced between partitions. This patch also
exports some page coalescing statistics available from firmware via
lparcfg.
[BenH: Moved a couple of things around to fix compile problems]
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Adapt new API.
Almost change is trivial. Most important change is the below line
because we plan to change task->cpus_allowed implementation.
- ctx->cpus_allowed = current->cpus_allowed;
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Icswx is a PowerPC instruction to send data to a co-processor. On Book-S
processors the LPAR_ID and process ID (PID) of the owning process are
registered in the window context of the co-processor at initialization
time. When the icswx instruction is executed the L2 generates a cop-reg
transaction on PowerBus. The transaction has no address and the
processor does not perform an MMU access to authenticate the transaction.
The co-processor compares the LPAR_ID and the PID included in the
transaction and the LPAR_ID and PID held in the window context to
determine if the process is authorized to generate the transaction.
The OS needs to assign a 16-bit PID for the process. This cop-PID needs
to be updated during context switch. The cop-PID needs to be destroyed
when the context is destroyed.
Signed-off-by: Sonny Rao <sonnyrao@linux.vnet.ibm.com>
Signed-off-by: Tseng-Hui (Frank) Lin <thlin@linux.vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Added support for ibm,configure-pe RTAS call introduced with
PAPR 2.2.
Signed-off-by: Richard A. Lary <rlary@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some of the 64bit PPC CPU features are MMU-related, so this patch moves
them to MMU_FTR_ bits. All cpu_has_feature()-style tests are moved to
mmu_has_feature(), and seven feature bits are freed as a result.
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
commit ec775d0e70 ("powerpc: Convert to new irq_*
function names") changed a call from set_irq_chip_data() to
irq_set_chip_data(), but forgot to update the corresponding debug message
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The goal is to avoid adding overhead to MMIO when only PIO is needed
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add the cputable entry, regs and setup & restore entries for
the PowerPC A2 core.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we start a cpu we use smp_ops->kick_cpu(), which currently
returns void, it should be able to fail. Convert it to return
int, and update all uses.
Convert all the current error cases to return -ENOENT, which is
what would eventually be returned by __cpu_up() currently when
it doesn't detect the cpu as coming up in time.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Wakeup comes from the system reset handler with a potential loss of
the non-hypervisor CPU state. We save the non-volatile state on the
stack and a pointer to it in the PACA, which the system reset handler
uses to restore things
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This uses feature sections to arrange that we always use HSPRG1
as the scratch register in the interrupt entry code rather than
SPRG2 when we're running in hypervisor mode on POWER7. This will
ensure that we don't trash the guest's SPRG2 when we are running
KVM guests. To simplify the code, we define GET_SCRATCH0() and
SET_SCRATCH0() macros like the GET_PACA/SET_PACA macros.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pass the register type to the prolog, also provides alternate "HV"
version of hardware interrupt (0x500) and adjust LPES accordingly
We tag those interrupts by setting bit 0x2 in the trap number
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is a significant rework of the XICS driver, too significant to
conveniently break it up into a series of smaller patches to be honest.
The driver is moved to a more generic location to allow new platforms
to use it, and is broken up into separate ICP and ICS "backends". For
now we have the native and "hypervisor" ICP backends and one common
RTAS ICS backend.
The driver supports one ICP backend instanciation, and many ICS ones,
in order to accomodate future platforms with multiple possibly different
interrupt "sources" mechanisms.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
PAPR specifies that DTL buffers can not cross AMS environments (aka CMO
in the PAPR) and can not cross a memory entitlement granule boundary
(4k). This is found in section 14.11.3.2 H_REGISTER_VPA of the PAPR.
kmalloc does not guarantee an alignment of the allocation, though,
beyond 8 bytes (at least in my understanding). Create a special kmem
cache for DTL buffers with the alignment requirement.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix some minor typos:
* informations => information
* there own => their own
* these => this
Signed-off-by: Sylvestre Ledru <sylvestre.ledru@scilab.org>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead, keep it static, expose an accessor and use that from
the PowerMac code. Avoids easy namespace collisions and will
make it easier to consolidate with other implementations.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On some machines that use i2c to synchronize the timebases (such
as PowerMac7,2/7,3 G5 machines), hotplug CPU would crash when
putting back a new CPU online due to the underlying i2c bus being
closed.
This uses the newly added bringup_done() callback to move the close
along with other housekeeping calls, and adds a CPU notifier to
re-open the i2c bus around subsequent hotplug operations
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current code soft-disables, and then goes to NAP mode which
turns interrupts on. That means that if an interrupt occurs, we
will hit the masked interrupt code path which isn't what we want,
as it will return with EE off, which will either get us out of
NAP mode, or fail to enter it (according to spec).
Instead, let's just rely on the fact that it is safe to take
decrementer interrupts on an offline CPU and leave interrupts
enabled. We can also get rid of the special case in asm for
power4_cpu_offline_powersave() and just use power4_idle().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Those instructions do nothing on non-threaded processors such
as 970's used on those machines.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use the generic code, just add the MPIC priority setting,
I don't see any use in mucking around with the decrementer,
as 32-bit will have EE off all along, and 64-bit will be able
to deal with it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use generic cpu_state, call idle_task_exit() properly, and
remove smp_core99_cpu_die() which isn't useful, the generic
function does the job just fine.
Remove the last remnants of cpu_enable(), everybody uses the normal
__cpu_up() path now
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Various thing are torn down when a CPU is hot-unplugged. That CPU
is expected to go back to start_secondary when re-plugged to re
initialize everything, such as clock sources, maps, ...
Some implementations just return from cpu_die() callback
in the idle loop when the CPU is "re-plugged". This is not enough.
We fix it using a little asm trampoline which resets the stack
and calls back into start_secondary as if we were all fresh from
boot. The trampoline already existed on ppc64, but we add it for
ppc32
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If a given firmware doesn't have a token to support query-cpu-stopped-state,
its not likely to change during the lifetime of the kernel.
Only print this information once, not once per secondary thread.
While here, make the line wrap grep friendly.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
To try to avoid future confusion, rename irq to hwirq when it refers
to a xics domain number instead of a linux irq number.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
commit 79f26c268e (powerpc:
platforms/pseries irq_data conversion) pushed irq_desc down into many
functions, dererencing the descriptor irq field as late as possible.
But it incorrectly passed a linix virtural irq number to RTAS,
resulting in the interrupt not being disabled and possibly
other bad things, such as another interrupt being disabled and/or
a checkstop.
In addition this missed the point of xics_mask_unknown_vec and
the seperation of xics_mask_real_irq from xics_mask_irq. When
xics_mask_unknown_vec is called it's because the hardware delivered an
irq source for which we have no linux irq allocated, and thefore we can
not have an irq_desc allocated.
Revert xics_mask_real_irq to its prior version, naming the argument
hwirq to highlight the difference.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For normal halt, reboot, and poweroff events, refrain from overwriting
the lnx,oops-log partition. Also, don't save the dmesg buffer on an
emergency-restart event if we've already saved it earlier in panic().
Signed-off-by: Jim Keniston <jkenisto@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The core irq_set_type() function updates the flow type when the chip
callback returns 0. It also updates irq_data, so this can be used in
irq_ack() to check for the level bit. That avoids a redundant sparse
irq lookup.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The irq chip has no irq_set_type() callback. So calling the call is
pointless. Set IRQ_LEVEL via the proper accessor.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
None of the existing cpufreq drivers uses the second argument of
its .suspend() callback (which isn't useful anyway), so remove it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
The MPC852 based mgsuvd board from Keymile was initially ported,
but later on not developed further. This patch removes the respective
files to decrease merging conflicts and unneeded maintenance.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher<hs@denx.de>
Cc: Vitaly Bordug <vitb@kernel.crashing.org>
Cc: Marcelo Tosatti <marcelo@kvack.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The mgcoge board from keymile is now base for some other
similar boards. Therefore the board specific name mgcoge
was renamed to a generic name km82xx. Additionally some
enhancements were made:
- rework partition table in dts file
- add cpm2_pio_c gpio controller in dts file
- update defconfig
- add pin description for SCC1
- add pin description and configuration for USB
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Heiko Schocher <hs@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Beside the MPC 8360 based board kmeter1 other km83xx boards
from keymile will follow. Therefore the board specific naming
kmeter1 for functions and files were replaced with km83xx.
Additionally some updates were made:
- update defconfig for 2.6.38
- rework flash partitioning in dts file
- add gpio controller for qe_pio_c in dts
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Heiko Schocher <hs@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If the spin table is located in the linear mapping (which can happen if
we have 4G or more of memory) we need to access the spin table via a
cacheable coherent mapping like we do on ppc32 (and do explicit cache
flush).
See the following commit for the ppc32 version of this issue:
commit d1d47ec6e6
Author: Peter Tyser <ptyser@xes-inc.com>
Date: Fri Dec 18 16:50:37 2009 -0600
powerpc/85xx: Fix SMP when "cpu-release-addr" is in lowmem
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
all remaining callers pass LOOKUP_PARENT to it, so
flags argument can die; renamed to kern_path_parent()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
On upcoming hardware, we have a PCI adapter with two functions, one of
which uses MSI and the other uses MSI-X. This adapter, when MSI is
disabled using the "old" firmware interface (RTAS_CHANGE_FN), still
signals an MSI-X interrupt and triggers an EEH. We are working with the
vendor to ensure that the hardware is not at fault, but if we use the
"new" interface (RTAS_CHANGE_MSI_FN) to disable MSI, we also
automatically disable MSI-X and the adapter does not appear to signal
any stray MSI-X interrupt.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The combination of commit
8154c5d22d and
93c22703ef
Broke boot on iSeries.
The problem is that iSeries very early boot code, which generates
the device-tree and runs before our normal early initializations
does need access the lppaca's very early, before the PACA array is
initialized, and in fact even before the boot PACA has been
initialized (it contains all 0's at this stage).
However, the first patch above makes that code use the new
llpaca_of(cpu) accessor, which itself is changed by the second patch to
use the PACA array.
We fix that by reverting iSeries to directly dereferencing the array. In
addition, we fix all iterators in the iSeries code to always skip CPU
whose number is above 63 which is the maximum size of that array and
the maximum number of supported CPUs on these machines.
Additionally, we make sure the boot_paca is properly initialized
in our early startup code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If firmware allows us to map all of a partition's memory for DMA on a
particular bridge, create a 1:1 mapping of that memory. Add hooks for
dealing with hotplug events. Dynamic DMA windows can use larger than the
default page size, and we use the largest one possible.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Create the lnx,oops-log NVRAM partition, and capture the end of the printk
buffer in it when there's an oops or panic. If we can't create the
lnx,oops-log partition, capture the oops/panic report in ibm,rtas-log.
Signed-off-by: Jim Keniston <jkenisto@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Adapt the functions used to create and write to the RTAS-log partition
to work with any OS-type partition.
Signed-off-by: Jim Keniston <jkenisto@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch below removes an extra "l" in the word.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Minor cleanup of notifier_from_errno() in powerpc.
notifier_from_errno() now contains the if(ret)/else conditional.
There is no need to do it in the powerpc code.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Get rid of old users of of_platform_driver in arch/powerpc. Most
of_platform_driver users can be converted to use the platform_bus
directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Spinlocks on shared processor partitions use H_YIELD to notify the
hypervisor we are waiting on another virtual CPU. Unfortunately this means
the hcall tracepoints can recurse.
The patch below adds a percpu depth and checks it on both the entry and
exit hcall tracepoints.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: stable@kernel.org
Currently, ppc32 uses sysdata for the pci_controller pointer, and
ppc64 uses it to hold the device_node pointer. This patch moves the
of_node pointer into (struct pci_bus*)->dev.of_node and
(struct pci_dev*)->dev.of_node so that sysdata can be converted to always
use the pci_controller pointer instead. It also fixes up the
allocating of pci devices so that the of_node pointer gets assigned
consistently and increments the ref count.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Mingkai Hu