On newer and faster machines (Vortex X86DX) using the r6040 driver, it
was noticed that the driver was returning an error during probing traced
down to being the MDIO bus probing and the inability to complete a MDIO
read operation in time. It turns out that the MDIO operations on these
faster machines usually complete after ~2140 iterations which is bigger
than 2048 (MAC_DEF_TIMEOUT) and results in spurious timeouts depending
on the system load.
Update r6040_phy_read() and r6040_phy_write() to include a 1
micro second delay in each busy-looping iteration of the loop which is a
much safer operation than incrementing MAC_DEF_TIMEOUT.
Reported-by: Nils Koehler <nils.koehler@ibt-interfaces.de>
Reported-by: Daniel Goertzen <daniel.goertzen@gmail.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Emitting netdev_alloc_skb and netdev_alloc_skb_ip_align OOM
messages is unnecessary as there is already a dump_stack
after allocation failures.
Other trivial changes around these removals:
Convert a few comparisons of pointer to 0 to !pointer.
Change flow to remove unnecessary label.
Remove now unused variable.
Hoist assignment from if.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are currently busy waiting for MDIO registers to complete their
operation but we did not propagate the result back to the caller.
Update r6040_phy_{read,write} to report the busy waiting result
accordingly.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures already get standardized OOM
messages and a dump_stack.
Convert kzalloc's with multiplies to kcalloc.
Convert kmalloc's with multiplies to kmalloc_array.
Fix a few whitespace defects.
Convert a constant 6 to ETH_ALEN.
Use parentheses around sizeof.
Convert vmalloc/memset to vzalloc.
Remove now unused size variables.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flags argument of the phy_{attach,connect,connect_direct} functions
is then used to assign a struct phy_device dev_flags with its value.
All callers but the tg3 driver pass the flag 0, which results in the
underlying PHY drivers in drivers/net/phy/ not being able to actually
use any of the flags they would set in dev_flags. This patch gets rid of
the flags argument, and passes phydev->dev_flags to the internal PHY
library call phy_attach_direct() such that drivers which actually modify
a phy device dev_flags get the value preserved for use by the underlying
phy driver.
Acked-by: Kosta Zertsekel <konszert@marvell.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
perm_addr is initialized correctly in register_netdevice() so to init it in
drivers is no longer needed.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use strlcpy where possible to ensure the string is \0 terminated.
Use always sizeof(string) instead of 32, ETHTOOL_BUSINFO_LEN
and custom defines.
Use snprintf instead of sprint.
Remove unnecessary inits of ->fw_version
Remove unnecessary inits of drvinfo struct.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __dev* removal patches for the network drivers ended up messing up
the function prototypes for a bunch of drivers. This patch fixes all of
them back up to be properly aligned.
Bonus is that this almost removes 100 lines of code, always a nice
surprise.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
as the manual of module_pci_driver says that
it can be used when the init and exit functions of
the module does nothing but the pci_register_driver
and pci_unregister_driver.
use it for rdc's r6040 driver, as the init and exit
paths does as above, and also this reduces a little
amount of code.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_set_drvdata is called twice at the remove path of driver,
call it once.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
so if mdiobus_alloc fails, the errorpath doesnt do a netif_napi_del and also
doesn't set the priv data of the driver to NULL.
at the driver unload stage the driver doesn't remove the NAPI context, and
doesnt' set the priv data to NULL, and also doesn't call the pci_iounmap.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the calls after the pci_enable_device may fail, and will error out with out
disabling it. disable the device at error paths.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define and use the bits of the PHY_CC (status change configuration) register.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define MTPR bit 0 of the register and use it where it is appropriate.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define the MLSR (MAC Last Status Register bits) for:
- tx fifo under-run
- tx exceed collision
- tx late collision
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are currently updating the rx fifo error counter in the tx path while
it should have been the tx fifo error counter, fix that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2048 is the usual value for busy-waiting on a register r/w, define it
as MAC_DEF_TIMEOUT and use it where it is appropriate.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reset of the MAC is currently done identically from two places
and one place is not waiting for the MAC_SM bit to be set after reset.
Everytime the MAC is software resetted a state machine is also needed
so consolidate the reset to its own function.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace usage of random_ether_addr() with eth_hw_addr_random()
to set addr_assign_type correctly to NET_ADDR_RANDOM.
Change the trivial cases.
v2: adapt to renamed eth_hw_addr_random()
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4e16d6ebd6 (r6040: define more MCR0
register bits) added #define values for MCR0 register bits and converted
uses of hardcoded magic values to uses of these defines.
However, one of the conversions looks suspicious:
#define MCR0 0x00 /* Control register 0 */
+#define MCR0_RCVEN 0x0002 /* Receive enable */
+#define MCR0_XMTEN 0x1000 /* Transmission enable */
/* Init RDC private data */
- lp->mcr0 = 0x1002;
+ lp->mcr0 = MCR0_XMTEN | MCR0;
I believe what was meant here was MCR0_XMTEN | MCR0_RCVEN, which makes
sense and matches the original values.
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch.pl complained about the line exceding 80 columns, and the
comment was actually on the same line as the code, fix that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
instead of __attribute__((__aligned(size)__))
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bit 1 is the reset bit of the MAC status machine register, define and
use it.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC_RST bit is already defined, use it instead of 0x1 where applicable.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define more MCR0-register bits and use them in place of the bits values.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the conversion to phylib (3831861b: r6040: implement phylib) some
PHY-related variables and definitions are now useless, remove them.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should use an unique MDIO bus name which does not clash with anything
else in the system like the Fixed MDIO bus. The bus is now named:
r6040-<card number> which is unique in the system.
Reported-by: Vladimir Kolpakov <vova.kolpakov@gmail.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are checking whether the MCR0_HASHEN bit is set using a logical and
instead of bitwise and, fix that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe reported to me that right after a bring up of a r6040 interface
the ethtool output had no consistent output with respect to link duplex
and speed. Fix this by adding a missing phy_start call in r6040_up and
conversely a phy_stop call in r6040_down to properly initialize phy states.
Reported-by: Joe Chou <Joe.Chou@rdc.com.tw>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the RDC driver into drivers/net/ethernet/rdc/ and make the
necessary Kconfig and Makefile changes.
CC: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>