The packet buffer is allocated at 4 bytes boundary, but the IP header
length and version bits is located at byte 14. These bit fields access
as 32 bits word and caused exception on processors that do not support
unaligned access.
The patch adds 2 bytes offset to make the bit fields word aligned.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer address in buffer descriptors is physical address. The
pointer that processor used to access packet is virtual address.
Though the higher bits of pointer address used by the MAC may be
truncated to zero in special case, it is not always true in larger
designs.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
It should be max() instead of min(). Use 1/4 of available
descriptors for tx, and there should be at least 2 tx
descriptors.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
in update_rx_stats() the RX_OVERLEN bit is set twice, replace it by RX_RUNT.
in au1000_rx() the RX_MISSED_FRAME bit was tested a few lines earlier already
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The closing parenthesis was not on the right location.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all pasemi mac interfaces can have a phy attached.
For example, XAUI has no phy and phydev is NULL for it.
In this case ethtool get settings causes kernel crash.
Fix it by returning -EOPNOTSUPP if there's no PHY attached.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
I was getting ribbed about this earlier, so I figured I'd make it
official. Add myself as the maintainer of the drop monitor bits, so
people don't just gripe at Dave when it breaks (I'm sure it will never
break, but just in case :) ).
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Felix Radensky noted that chip resets were generating stack trace dumps.
This is because the driver is attempting to acquire the mdio bus mutex
while holding the tp->lock spinlock. The fix is to change the code such
that every phy access takes the tp->lock spinlock instead.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like a typo, FUTEX_WAKE_BITS should be FUTEX_WAIT_BITSET.
Signed-off-by: Anton Blanchard <anton@samba.org>
LKML-Reference: <20091007001358.GE16073@kryten>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This fixes a bug with arp_notify.
If arp_notify is enabled, kernel will crash if address is changed
and no IP address is assigned.
http://bugzilla.kernel.org/show_bug.cgi?id=14330
Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like the big Kconfig cache split/rename missed one spot in the SMP
cache lock headers.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The cplbinfo was using d_path() to figure out which cpu/cplb was being
parsed. As Al pointed out, this isn't exactly reliable as it assumes the
static VFS path to be unchanged, and it's just poor form. So use the
proc_create_data() to properly (and internally) pass the exact cpu/cplb
requested to the parser function.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The asm/irq.h header uses anomaly defines, but doesn't make sure to
explicitly include the anomaly header for them.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Bill Gatliff & David Brownell pointed out we were missing some
copyrights, and licensing terms in some of the files in
./arch/blackfin, so this fixes things, and cleans them up.
It also removes:
- verbose GPL text(refer to the top level ./COPYING file)
- file names (you are looking at the file)
- bug url (it's in the ./MAINTAINERS file)
- "or later" on GPL-2, when we did not have that right
It also allows some Blackfin-specific assembly files to be under a BSD
like license (for people to use them outside of Linux).
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Convert Blackfin to use GENERIC_TIME via the arch_getoffset()
infrastructure, reducing the amount of arch specific code we need to
maintain.
I've taken my best swing at converting this, but I'm not 100% confident
I got it right. My cross-compiler is now out of date (gcc4.2) so I
wasn't able to check if it compiled. Any assistance from arch
maintainers or testers to get this merged would be great.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Before this patch, all of the rcu_node structures were in the same lockdep
class, so that lockdep would complain when rcu_preempt_offline_tasks()
acquired the root rcu_node structure's lock while holding one of the leaf
rcu_nodes' locks.
This patch changes rcu_init_one() to use a separate
spin_lock_init() for the root rcu_node structure's lock than is
used for that of all of the rest of the rcu_node structures, which
puts the root rcu_node structure's lock in its own lockdep class.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: laijs@cn.fujitsu.com
Cc: dipankar@in.ibm.com
Cc: akpm@linux-foundation.org
Cc: mathieu.desnoyers@polymtl.ca
Cc: josh@joshtriplett.org
Cc: dvhltc@us.ibm.com
Cc: niv@us.ibm.com
Cc: rostedt@goodmis.org
Cc: Valdis.Kletnieks@vt.edu
Cc: dhowells@redhat.com
LKML-Reference: <12548908983277-git-send-email->
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The current interaction between RCU and CPU hotplug requires that
RCU block in CPU notifiers waiting for callbacks to drain.
This can be greatly simplified by having each CPU relinquish its
own callbacks, and for both _rcu_barrier() and CPU_DEAD notifiers
to adopt all callbacks that were previously relinquished.
This change also eliminates the possibility of certain types of
hangs due to the previous practice of waiting for callbacks to be
invoked from within CPU notifiers. If you don't every wait, you
cannot hang.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: laijs@cn.fujitsu.com
Cc: dipankar@in.ibm.com
Cc: akpm@linux-foundation.org
Cc: mathieu.desnoyers@polymtl.ca
Cc: josh@joshtriplett.org
Cc: dvhltc@us.ibm.com
Cc: niv@us.ibm.com
Cc: peterz@infradead.org
Cc: rostedt@goodmis.org
Cc: Valdis.Kletnieks@vt.edu
Cc: dhowells@redhat.com
LKML-Reference: <1254890898456-git-send-email->
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add kerneldoc comments to some functions in the Gigaset driver.
Impact: documentation
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dump payload data consistently only when DEBUG_STREAM_DUMP debug bit
is set.
Impact: debugging aid
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the Gigaset base stops responding, try resetting the USB
connection to recover.
Impact: error handling improvement
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear out pending command that got rejected with 'ERROR' response.
This fixes the bug where unloading the driver module would hang
with the message: "gigaset: not searching scheduled commands: busy"
after a device communication error.
Impact: error handling bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mention in the driver load announcement whether the driver was built
with debugging messages enabled, to facilitate support.
Impact: informational message
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't drop the remainder of an URB if an isochronous frame has an error.
Impact: error handling improvement
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code of the Gigaset driver assumes that sk_buff-s coming
from the ISDN4Linux subsystem are always linear. Explicitly
calling skb_linearize() is cheap if they are, but much more
robust in case they ever aren't.
Impact: robustness improvement
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signal D channel disconnect in a few cases where it was missed,
including when an incoming call is disconnected before it was
accepted.
Impact: error handling improvement
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Being able to change the debugmode module parameter of capidrv on the
fly is quite useful for debugging and doesn't do any harm.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
In several places, capidrv sends a CAPI message to the ISDN
device and then updates its internal state accordingly.
If the response message from the device arrives before the
state is updated, it may be rejected or processed incorrectly.
Avoid these races by updating the state before emitting the
message.
Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Acked-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Info values in the 0x00xx range are defined in the CAPI standard
as "Informational, message processed successfully". Therefore a
CONNECT_B3_CONF message with an Info value in that range should
open an NCCI just as with Info==0.
Impact: minor bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Acked-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Note that send_message() may be called in interrupt context.
- Describe the storage of CAPI messages and payload data in SKBs.
- Add more details to the description of the _cmsg structure.
- Describe kernelcapi debugging output.
Impact: documentation
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
* use 8 clk setting for active clocks == 7 (was 12 clk)
* use 12 clk setting for active clocks > 12 (was 8 clk)
* do 66MHz bus fixup before mapping active clocks
* fix setup of PIO command timings
Acked-by: Jung-Ik (John) Lee <jilee@google.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
MWDMA modes are not supported by this driver currently.
Acked-by: Jung-Ik (John) Lee <jilee@google.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
While trying to work around spurious detection retries for
non-existent devices on slave links, commit
816ab89782 incorrectly added link
offline check logic before ata_eh_thaw() was called. This means that
if an occupied link goes down briefly at the time that offline check
was performed, device class will be cleared to ATA_DEV_NONE and libata
wouldn't retry thus failing detection of the device.
The offline check should be done after the port is thawed together
with online check so that such link glitches can be detected by the
interrupt handler and handled properly.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Tim Blechmann <tim@klingt.org>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is a fix for a bug which was a result of wrong use of checksum offload flag.
The status of tx-checksumming was not changed from on to off
after a 'ethtool -K <ifname> tx off' operation.
Use the proper checksum offload flag NETIF_F_HW_CSUM instead of
NETIF_F_IP_CSUM and NETIF_F_IPV6_CSUM.
Patch is against net-2.6 tree.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MCC_STATUS_NOT_SUPPORTED should be decimal 66 not hex 66.
This patch fixes this typo. Patch against net-2.6 tree.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While updating the statistics to be passed via the get_stats,
tx multicast frames were being accounted instead of rx multicast frames.
This patch fixes the bug. This patch is against the net-2.6 tree.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of spinlock and private mutex usage for exclusive access to the
HW semaphore register. rtnl_lock already creates exclusive access to
this register in all driver API.
Add rtnl to firmware worker threads that also use the HW semaphore register.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check that we are not already polling firmware events before we queue the
firmware event worker, then disable firmware interrupts.
Otherwise we can queue the same event multiple times.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a typo which causes try_location() to use the wrong length argument
when calling nfs_parse_server_name(). This again, causes the initialisation
of the mount's sockaddr structure to fail.
Also ensure that if nfs4_pathname_string() returns an error, then we pass
that error back up the stack instead of ENOENT.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
As seen in <http://bugs.debian.org/549002>, nfs4_init_client() can
overrun the source string when copying the client IP address from
nfs_parsed_mount_data::client_address to nfs_client::cl_ipaddr. Since
these are both treated as null-terminated strings elsewhere, the copy
should be done with strlcpy() not memcpy().
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The recent changeset 53a0b9c4c9 (NFS: Replace
nfs_parse_ip_address() with rpc_pton()) broke nfs_remount, since the call
to rpc_pton() will zero out the port number in data->nfs_server.address.
This is actually due to a bug in nfs_remount: it should be looking at the
port number in nfs_server.port instead...
This fixes bug
http://bugzilla.kernel.org/show_bug.cgi?id=14276
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Currently, the port and mount port will both display as 65535 if you do not
specify a port number. That would be wrong...
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
With the recent spate of changes, the nfs protocol version will now default
to 2 instead of 3, while the mount protocol version defaults to 3.
The following patch should ensure the defaults are consistent with the
previous defaults of vers=3,proto=tcp,mountvers=3,mountproto=tcp.
This fixes the bug
http://bugzilla.kernel.org/show_bug.cgi?id=14259
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Thomas Chou