Configure the fw to filter multicast according to
the addresses given by mac80211.
Note that bssid should be given even if we want
to pass all the multicast frames.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This allows to tweak the power parameters per vif.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enable power save on P2P client interface only if it is the
only bound interface.
Avoid using uAPSD if P2P client is associated to GO that uses
opportunistic power save. This is due to current FW limitation.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When monitor interface is activated device power save needs
to be disabled.
Re-consider power management status on other active
interfaces when monitor interface is bound or unbound.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
FW still does not support power management on multiple MAC interfaces.
Currently the driver enforce this limitation by disabling PM if second
interface is added. Change this behavior to allow PM on a single interface
even if other interfaces exist but not bound to any specific PHY.
PM will be enabled if only one single interface is bound.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
FW implements protective algorithm to identify AP's improper uAPSD
behavior. FW sends misbehaving AP notification in this case.
Add this notification handling. Avoid using uAPSD in next association
to the exactly same AP. Refactor iwl_mvm_power_build_cmd() to move
uAPSD related code to a separate function.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This patch adds a cipher scheme support to extend a set of
the supported ciphers. The driver reads a cipher scheme list TLV
from FW image and passes it to mac80211 on hw registration.
After the cipher schemes are registered the driver handles key
installation and Tx/Rx calls related to the new ciphers.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Send firmware a Smart FIFO Configuration host command to allow
interrupt coalescing. The smart FIFO is enabled when there is
only one bound interface (other than p2p devices which are
ignored) and it is of type station, and activated while the
station is associated.
Smart Fifo allows aggragations of DMA transactions and by that
causes processor and memory controller to stay for a longer time
on lower c-states, thus saving platform power.
Firmware relies on driver to activate and disable it.
Signed-off-by: Lilach Edelstein <lilach.edelstein@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
iwlmvm relies on the current mac80211 behaviour of allowing
station pointers to be valid for an RCU grace period after
returning from the sta_state() callback. To optimise these
cases, this behaviour is going away, so make the driver use
the new sta_pre_rcu_remove() method to clear the pointer in
the fw_id_to_mac_id[] array.
Since this may happen while the station is still present in
the firmware, don't set the pointer to NULL but to -ENOENT
to mark this particular case. In client mode, the station
is kept even longer (until marking the MAC as unassociated)
so the drain flow must take this new behavior into account.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Products that have only 1 antenna in Rx don't support MIMO
in RX. As a consequence, they will be in STATIC always.
Don't tell mac80211 to update SMPS in that case. mac80211
would send an action frame to the AP which is clearly
bogus.
As a matter of fact, we have seen that some APs send a
deauth when that happens.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Sync to SCO is a feature that allows to synchronise the
wifi activity with the predictable BT activity in
SCO profile. This allows to reduce the collisions and
improve overall quality.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Rewrite the search cycle state machine to use a more data
oriented approach where the different Tx columns (configs)
limitations and next columns to search are reprsented in
tables which are easy to change. This overhaul also includes
several major fixes:
1. Prevent going back to a specific Tx column in a search
cycle if it was already explored.
2. Avoid switching to a Tx column that doesn't have any chance
if it performs perfectly to beat the current throughput we're
getting.
These issues were degrading throughput as they were causing
switching to "bad" Tx columns.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Use the 20Mhz channel width define instead of just the number
zero for legacy rates. Note that the define has the same value
so this is just a minor cleanup.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The table rs_ht_to_legacy is used to get the next legacy rate
following the last HT or VHT rate in the LQ rates table.
The mapping wasn't correct as well as didn't include entries
for MCS8/9 which led to out of bounds access. This didn't
trigger a crash but led to legacy rate entries using 1Mbps
rate.
In 5Ghz this probably caused the Tx to fail completely given
that Tx attempt would have reached the legacy entries and 1Mbps
isn't valid.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Drop code which was relevant when there were chips with
3 antennas. Setting to ANT_AB should be ok with all mvm
supported chips.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Introduce rs_rate which represents a rate. Use this structure
instead of iwl_scale_tbl_info where we're dealing with a single
rate.
This avoids allocating the big iwl_scale_tbl_info structure
on the stack in several cases like converting to ucode rate
format or from ucode rate format.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Remain in the same Tx modulation (i.e. column) for a longer
time before starting a search cycle for a better modulation.
This has been shown to give better results.
Also change the name of the timeout define to better match its
description.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Expected TPT table was updated only when switching to a new
modulation. This is wrong as toggling aggregation changes
the expected TPT signficantly.
This leads to scenarios where turning aggregation on after
being in MIMO sends us back to SISO despite a perfect success
ratio.
This occurred because the TPT of the SISO mode was being
estimated based on aggregation while the MIMO one wasn't.
Also remove an error print which isn't an error anymore
since we might be updating the expected TPT table due
to aggregation changes.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This terminates a test window of a new rate quicker in case
we've hit a bad rate and should recover better.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enable better tracking of different decisions made
by the rate scale algorithm.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Remote peer can publish a different number of supported nss via the
operating mode notification IE or action frame. If it limits to 1
then we don't want mimo rates configured in the rate table.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
MCS9 in NSS=1 or NSS=2 isn't valid for 20Mhz so don't enable
it in case we're dealing with a 20Mhz sta. Trying to configure an
MCS9 rate with 20Mhz in the LQ rate table would lead to a FW assert.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Switch to using the new btcoex decision api regarding MIMO and stop
accessing the internal btcoex structs.
In case MIMO should be disabled it would detect this upon the next
Tx and force a search. The search will switch to SISO on a antenna A
which isn't used by BT.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
For now, the firmware doesn't really use the field, but
it should be set to zero if there's no specific request.
Setting it to the max quota doesn't make sense.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Advertise driver's support for low priority scan.
Notice that this overwrites current setting by mac80211 which depends
only on hw scan support.
This scan priority can be configured by user space application
and it affects scan continuity, low priority scan
will be more fragmented scan.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Bit 0 in the scan offloading flags asks the filter
to pass all the results (instead of filtering them,
by default), rather than the other way around (like
it is defined and used today).
Fix the flag name appropriately, and fix its user.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This allows to see the content of the NVM the driver reads.
Note that the output is in binary, and requires some
external user space tool to display the data properly.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If we haven't loaded the D3 image yet and a failure in the suspend
process occurs, we shouldn't restart the HW, because we're still
running the D0 image.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This is just a helper function to go from the mac80211
station struct to our internal one, to later allow us
to avoid temporary 'mvmsta' variables.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
valid_rx_ant is a bitmask of available antennas and not the number
of Rx antennas. Use num_of_ant and remove duplicate definitions
in both dvm and mvm.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Latest tests have shown that when BT is active and has
connections but the traffic is low, the WiFi aggregation can
be large up to 4000us without noticeable impact on BT.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add more bit field definitions used in LQ flags.
Also rename the first bit to a shorter name.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Abstract the copy_from_user() pattern into the macros defining
debugfs files, reducing the code and making adding new files
safer by avoiding having deal with copy_from_user() directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There's really no reason to use void *dbgfs_data
rather than a struct iwl_mvm *mvm, so do that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The debugfs file is getting pretty large and mixed up between
code for the hardware and code for each interface (the two
aren't even clearly separated in the code). Make it easier to
handle by splitting the per-interface code into a separate
file called debugfs-vif.c.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Just clean up the code a bit, in particular
* make all the debugfs writes follow the same pattern
with respect to buf/buf_size variables
* get rid of useless comments
* check return values of all file creations
* drop unnecessary parentheses
* remove an unused struct definition
* fix some whitespace
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The HT protection flags have been a mess for a long time,
this patch fixes all this.
The proper source of information for this is the
protection in the HT operation mode IE which is
propagated to bss_conf by mac80211.
1) No need to set the HT protection flags when the link
doesn't support HT.
2) We need to set the TGG protection when ERP is active.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Keeping connection can be useful also when testing d3
using the debugfs file (d3_test).
Save the vif to keep connection on, and consider it
when iterating over the interfaces.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Re-initialize rs when we get a rate_update hook called which
happens when remote STA changes bandwidth or sends a VHT opmode
notification.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When waking up from d3 due to disconnection event
(e.g. because of beacon loss), we should disconnect
immediately.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Even if d3_test_pme_ptr is not available, d3_test can still
be useful, e.g. by manually triggering resume (with ctrl-c),
and reading the wakeup reasons.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Refactor setting of VHT enabled rates in preparation of adding
some more logic there.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Remove the flags parameter which should be set to sync or async
according to whether this is called during sta init or not.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Info about VHT/HT rates wasn't printed properly when dumping
the rate scale table. Fix that and print more info. While at it
fix some other minor issues in the printing and prevent
overflowing the print buffer.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Writting to fw_nmi entry will set DEVICE_SET_NMI_REG (0x00a01c30)
generating NMI that halts NIC CPU.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The transport layer doesn't need to know the TX_CMD id.
It can be set by the op_mode.
The transport layer still needs to know the layout of the
Tx command because of alignment issues and because of the
scratch pointer.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If the next seqno returned by the firmware is 0, we return an error
(-16) in the iwl_mvm_get_last_nonqos_seq() function. This is because
we return an integer and don't use any casting when calculating the
last seqno from the one we received. Fix this by using a cast to u16
when doing the calculation, so we return 0xfff0, as we should.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In an open BSS, after suspend/resume, we don't set the last seqno
because the iwl_mvm_setup_connection_keep() returns too early. This
happens because the check to see if we have any keys was returning
immediately, without setting seqno and seqno_valid. Fix this.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Time event notification can have a failure status even if
the time event was scheduled:
* in START notification, this can happen if the time event
was scheduled later than the requested apply time.
* in STOP notification, this can happen if the time event
is truncated.
Even if both happened, the offchannel packets sent during
the remain on channel are very likely to have been sent.
Hence, don't WARN when this happens, but rather print a
discrete line in the kernel log.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
This patch is very similar to a previous fix: 22cba0c085
When we disassociate, mac80211 removes the station and
then, it sets the bss it unsets the assoc bool in bss_info.
Since the firwmware wants it the opposite (first set the
MAC context as unassoc, and only then, remove the STA of
the API), we have a small period of time in which the STA
in firmware doesn't have a valid ieee80211_sta pointer.
During that time, iwl_mvm_vif->ap_sta_id, is still set
to the STA in firmware that represent the AP.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This feature isn't supported by the firmware (yet).
Note that settingt he values to BT_CFG_CMD is harmless if
the validity bit is clear - so keep the configuration
values in BT_CFG_CMD, but clear the validity bit until thes
feature is enabled in the firmware.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The station ID must be valid, if it's out of range then
the array access may crash. Validate the station ID to
the array length, and also validate the drain value even
if that doesn't matter all that much.
Cc: stable@vger.kernel.org
Fixes: 8ca151b568 ("iwlwifi: add the MVM driver")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
These two flags are used for the same purpose, just
combine them into a no-ir flag to annotate no initiating
radiation is allowed.
Old userspace sending either flag will have it treated as
the no-ir flag. To be considerate to older userspace we
also send both the no-ir flag and the old no-ibss flags.
Newer userspace will have to be aware of older kernels.
Update all places in the tree using these flags with the
following semantic patch:
@@
@@
-NL80211_RRF_PASSIVE_SCAN
+NL80211_RRF_NO_IR
@@
@@
-NL80211_RRF_NO_IBSS
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_PASSIVE_SCAN
+IEEE80211_CHAN_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IBSS
+IEEE80211_CHAN_NO_IR
@@
@@
-NL80211_RRF_NO_IR | NL80211_RRF_NO_IR
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IR | IEEE80211_CHAN_NO_IR
+IEEE80211_CHAN_NO_IR
@@
@@
-(NL80211_RRF_NO_IR)
+NL80211_RRF_NO_IR
@@
@@
-(IEEE80211_CHAN_NO_IR)
+IEEE80211_CHAN_NO_IR
Along with some hand-optimisations in documentation, to
remove duplicates and to fix some indentation.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[do all the driver updates in one go]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Putting the context id of the primary phy context in
the placeholder of the secondary is obviously a bad
idea.
Spotted by smatch.
Fixes: dac94da8db ("iwlwifi: mvm: new BT Coex API")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reported by "make includecheck"
Tested that the corresponding sources still compile well on x86
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If the firmware image that we attempt to load doesn't
actually exist we have a broken firmware file or other
code not checking things correctly, so warn in such a
case. Also avoid assigning cur_ucode/ucode_loaded then.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When writing the disable_power_off value, the LPRX
enable value also gets written unintentionally, so
fix that by adding the missing break statement.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This can be useful when using the device as a sniffer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Change old UAPSD bit to PM_CMD_SUPPORT, and add a new bit to indicate
real UAPSD support.
Don't use UAPSD when the firmware doesn't support it.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Conflicts:
drivers/net/usb/qmi_wwan.c
include/net/dst.h
Trivial merge conflicts, both were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Integers need to be multiplied before division.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The fw_rx_stats entry in debugfs was getting truncated because the
internal buffer used to hold the string was too short. The
calculation of the needed buffer size was rather bogus.
Simplify the calculation by multiplying the number of entries in the
entire structure by the size of each data line and adding the size of
the header lines.
Additionally, add the mac_id value, which was missing.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The activity grading indication from the firmware should
not be used in this case, but the bt_status in the firwmare
notification.
Fix that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware always expects the Coex Mode to be set.
Moreover, the firmware expects bit 0 is the valid bits to
be set all the times.
I misunderstood the API and didn't set these bits when
commands are sent to update the paramters of the Coex. As
a result, the firmware understood that the BT Coex was
disabled (Coex mode = 0) and ignored all the updates (valid
bit 0 clear).
Fix that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Section size limitation to 6000 is incorrect.
NVM file need to support bigger sections in order
to support PAPD tables.
Signed-off-by: Idan Kahlon <idanx.kahlon@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Maor Perez <maorx.perez@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This fix is related to a scan request when associated (bgscan).
FW expects suspend time parameter in micro seconds while the driver
provides a value in time units. This bug leads to a high traffic
latency when scan is requested while traffic is in progress.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At the firmware level, IBSS support has similar programming
requirements as AP/GO support, so use the same functions with
just small differences.
With IBSS only a single virtual interface can be used, so no
changes in the advertised interface combinations are needed.
For now, don't use hardware crypto for the GTKs in IBSS mode,
the firmware should support it though.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove code that is not needed and always allow MIMO when
in tight mode. In loose mode, we should avoid MIMO since BT
can use the other antenna to Rx while we Tx.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code limiting the AMPDU length due to BT traffic was
duplicated. Remove the redundant code.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tests have shown that we should start AMPDU even when BT
is active. So remove that constraint.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tests have shown that we should go SMSP_STATIC when BT
traffic is high, and stay in dynamic if BT traffic is low.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
BT Coex needs to be updated when the bandwidth is modified
by the AP.
While at it, remove the vif parameter from
bt_coex_vif_change since it was unused.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Until now, after WoWLAN, we weren't able to keep the
connection to the AP because the firmware didn't give
us the right information. Since the firmware API has
been changed to include all the information we need,
change the driver to work with the new API (if it is
available) and program all the relevant information
in mac80211 to keep the connection.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some NICs embedded in platforms that have only 16 Tx queues,
this affect the mapping of the Tx queues.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some NICs aren't allowed to be powered up at driver load time.
Fix it, and move the external NVM loading from driver load time to
driver up time (parsing the external nvm file remains at driver load time).
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
FW starts using legacy power table command (0x77) for device wide power
settings. Currently this command contains only option flags field.
It can configure the following: CAM (Continuous Active Mode) and
POWER_SAVE_ENABLE debug option. Send this command when firmware is
loaded - D0 and D3.
Note: Setting this command is important to avoid unwanted FW behavior.
It particularly fixes a bug when a device does not drop to low power
after disassociation from AP.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Single shared antenna devices need a special LUT.
Address this need.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In loose BT Coex scheme, the aggregation size doesn't need to
be limited.
To avoid triggering it, remove a lockdep assertion - we need
to compute the AMPDU size limit from rate control code which
can't take mvm->mutex. This means that there is a race but in
the worst case, we will have a wrong AMPDU size limit which
is not a big issue.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In RF KILL the init ucode is running, but don't complete
all its tasks, so we need to run the init ucode again.
Change the flag name to init_ucode_complete, to be more appropriate.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware API for IPv6 NDP/NS offload has changed again.
Implement support for the new API; this requires calculating
the solicited node address for each "target" address as it's
no longer ignored by the firmware.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rssi events were enabled on interfaces using 5.2GHz.
Interfaces on 5.2GHz were taken into account while
determining the ACK / CTS kill mask. Fix that.
The last rssi notified to BT Coex was reset every BT Coex
Notification. Since we get a lot of these notifications
from the firmware, we reset the rssi all the time which
means that the bt_rssi_event is called all the time.
Fix that by puting the rssi we pull upon BT Coex
notification into iwl_mvm_vif_bf_data.last_bt_coex_event
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we have only one antenna for BT and WiFi, reduced Tx
power is irrelevant.
Also, in loose scheme, we should not use reduced Tx power
nor set the control mask to Tx power.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some debugfs write() operations of the MVM Firmware will ignore the
count argument, and will copy more bytes than what was specified.
Fix this by getting the right count of bytes.
This will honor restrictions put on the number of bytes to write and
avoid strcmp() calls on garbage data.
Signed-off-by: Djalal Harouni <tixxdz@opendz.org>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mvm doesn't support HT GF so drop all relevant code in rs.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Enable rs algorithm to use VHT rates and use 80Mhz.
This enables reaching VHT rates which wasn't possible.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The data in MailBox comes direclty from the BT core.
We should use the data processed by the WiFi fw that is
appended to the MailBox in the BT Coex notification.
Also decide on whether the Coex type based on the input
from the the firmware and not hard coded.
Also fix the SMPS SISO threshold to 2 (it was 3).
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Eliad Peller