Adds AM33XX EDMA support to the am33xx.dtsi as documented in
Documentation/devicetree/bindings/dma/ti-edma.txt
[Joel Fernandes <joelf@ti.com>]
Drop DT entries that are non-hardware-description as discussed in [1]
[1] https://patchwork.kernel.org/patch/2226761/
Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Without this node, there will be no palmas driver to notify
dwc3 that a cable has been connected and, without that, dwc3
will never initialize.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[kishon@ti.com: added dt properties for enabling vbus/id interrupts
and fixed vbus-supply value after SMPS10 is modeled as 2 regulators]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Use a common naming scheme "mode0name.modename flags" for the
USB host pins to be consistent.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This adds devicetree for gta04 (Openmoko next generation board) with necessary
support for mmc, usb, leds and button.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Populate uarts, timers, rtc, wdt, gpio, i2c, spi, cpsw & pwm nodes.
Reason for adding these nodes early - hwmod code required address
space of peripherals corresponding to these nodes (as address space
details are removed from hwmod database).
uart0, timers - 1 & 2 and synctimer were already present, so here the
remaining uarts & timers are added.
All properties as per the existing binding has been added for uart,
timer, rtc, wdt & gpio. Even though that was not the current scope
of work, felt adding those would reduce or require no effort later
to get these peripherals working.
For i2c, spi, cpsw & pwm - only the properties that were sure to be
correct has been added (main intention is to make hwmod happy and
avoid any later modification to here added properties).
While at it add "ti,hwmod" property to already existing nodes.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Update AM4372 cpu node to the latest cpus/cpu bindings for ARM.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add minimal device tree source needed for DRA7 based SoCs.
Also add a board dts file for the dra7-evm (based on dra752)
which contains 1.5G of memory with 1G interleaved and 512MB
non-interleaved. Also added in the board file are pin configuration
details for i2c, mcspi and uart devices on board.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The OMAP4 SoC family uses specially-designed PMIC (power management IC)
companion chip for power management needs: TWL6030/TWL6032.
Therefore there is a typical connection of PMIC to OMAP4 so we can
move it into separate .dtsi file and do not duplicate over
board-specific files.
Tested on OMAP4 SDP board and Pandaboard ES2.
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
SMPS10 has two outputs OUT1 and OUT2. Hence SMPS10 is modeled as
two regulators. The DT node is split to reflect it.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Following commit ff5c9059 and therefore other omap platforms using
the gpio-omap driver correct the #interrupt-cells property on am33xx
too. The omap gpio binding documentaion also states that
the #interrupt-cells property should be 2.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
ARM Performance Monitor Units are available on the am33xx,
add the support in the dtsi.
Tested with perf and oprofile on a regular beaglebone.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The IGEP COM MOdule has a GPIO LED connected to OMAP
pins. Configure this pin as output GPIO.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The IGEPv2 has a number of GPIO LED connected to OMAP
pins. Configure these pins as output GPIO.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
IGEP boards have a number of LED connected to OMAP or TWL GPIO
lines. The actual wiring is different on each board so each board
DT has need to configure the mux correctly.
Even though it works with the current DT, the kernel complains with:
[2.305023] leds-gpio leds.18: pins are not configured from the driver
Add an empty pinmux_leds_pins pinctrl child node so boards can
override with the correct mux configuration and not depend on
default values for the GPIO LEDs to work.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This adds device tree with necessary support to boot with functional
video (on both emulator and real N900 device).
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
We have a fairly large batch of fixes this time around, mostly just due to
various platforms all having a fix or two more than usual.
Worth pointing out are:
- A fix for EDMA on Davinci/OMAP where channel allocation broke with
the DT conversion. Due to some miscommunication we didn't
understand the impact of the breakage, so we were pushing back on it
for 3.12, but it sounds like it's actually breaking quite a few people
out there.
- A bunch of fixes for Marvell platforms, some straggling fixes for
merge window fallout and some fixes for a couple of the platforms
(Netgear RN102 in particular).
- A fix for a race between multi-cluster power management and cpu hotplug
on Versatile Express.
And a bunch of other smaller fixes that all add up.
We'll be switching over into stricter regressions-only mode from here
on out.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=DLem
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We have a fairly large batch of fixes this time around, mostly just
due to various platforms all having a fix or two more than usual.
Worth pointing out are:
- A fix for EDMA on Davinci/OMAP where channel allocation broke with
the DT conversion. Due to some miscommunication we didn't
understand the impact of the breakage, so we were pushing back on
it for 3.12, but it sounds like it's actually breaking quite a few
people out there.
- A bunch of fixes for Marvell platforms, some straggling fixes for
merge window fallout and some fixes for a couple of the platforms
(Netgear RN102 in particular).
- A fix for a race between multi-cluster power management and cpu
hotplug on Versatile Express.
And a bunch of other smaller fixes that all add up.
We'll be switching over into stricter regressions-only mode from here
on out"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
ARM: multi_v7_defconfig: add SDHCI for i.MX
bus: mvebu-mbus: Fix optional pcie-mem/io-aperture properties
ARM: mvebu: add missing DT Mbus ranges and relocate PCIe DT nodes for RN102
ARM: at91: sam9g45: shutdown ddr1 too when rebooting
MAINTAINERS: ARM: SIRF: use kernel.org mail box
MAINTAINERS: ARM: SIRF: add missed drivers into maintain list
ARM: edma: Fix clearing of unused list for DT DMA resources
ARM: vexpress: tc2: fix hotplug/idle/kexec race on cluster power down
ARM: dts: sirf: fix interrupt and dma prop of VIP for prima2 and atlas6
ARM: dts: sirf: fix the ranges of peri-iobrg of prima2
ARM: dts: makefile: build atlas6-evb.dtb for ARCH_ATLAS6
ARM: dts: sirf: fix fifosize, clks, dma channels for UART
ARM: mvebu: Add DT entry for ReadyNAS 102 to use gpio-poweroff driver
ARM: mvebu: fix ReadyNAS 102 Power button GPIO to make it active high
ARM: mach-integrator: Add stub for pci_v3_early_init() for !CONFIG_PCI
ARM: shmobile: Remove #gpio-ranges-cells DT property
gpio: rcar: Remove #gpio-range-cells DT property usage
ARM: shmobile: armadillo: fixup ether pinctrl naming
ARM: shmobile: Lager: add Micrel KSZ8041 PHY fixup
ARM: shmobile: update SDHI DT compatibility string to the <unit>-<soc> format
...
- mvebu
- fix ReadyNAS 102 power button (needs to be active high)
- fix ReadyNAS 102 automated rebooting (prevent hang) by add gpio-poweroff
node
- fix booting ReadyNAS 102 by adding MBus ranges and PCIe DT nodes
- mvebu-mbus: prevent PCIe driver from continuing with corrupted resource
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)
iQEcBAABAgAGBQJSTERhAAoJEAi3KVZQDZAeFaQH/jmhAZwvSrB7MeTTY7J9eAcl
n4cFHImBiSb6IdDaocKB+yOmEgq/X2LS/DjK71sa0+CQsTq9B5nHxMHioogdUrG7
S8ofIjqu90CBOZ1I5IMSPmA3uOc1B2+wYi9uLxmajMTzYVDDBEZh9LuMy/GjwzU2
/g09RedQ3XkWDVv3pdPdEiC6KZ/gg7gejxOLv0nv9ydxr0DB8/VwmBHWFC0ghawB
3EchoagJ3M+mAbUaxtY6cauV2nnAJOO5mV6ZHl2tIOj4/Mhn8Le/C1t+Zcdf+U82
iAvqWmiRc3Vk96g8xXZWwZoPL7vhidLcE7dpOIZ2ymq5+g3esTaailqRxRqS9+c=
=uNPR
-----END PGP SIGNATURE-----
Merge tag 'fixes-3.12-2' of git://git.infradead.org/linux-mvebu into fixes
From Jason Cooper:
mvebu fixes for v3.12 (round 2)
- mvebu
- fix ReadyNAS 102 power button (needs to be active high)
- fix ReadyNAS 102 automated rebooting (prevent hang) by add gpio-poweroff
node
- fix booting ReadyNAS 102 by adding MBus ranges and PCIe DT nodes
- mvebu-mbus: prevent PCIe driver from continuing with corrupted resource
* tag 'fixes-3.12-2' of git://git.infradead.org/linux-mvebu:
bus: mvebu-mbus: Fix optional pcie-mem/io-aperture properties
ARM: mvebu: add missing DT Mbus ranges and relocate PCIe DT nodes for RN102
ARM: mvebu: Add DT entry for ReadyNAS 102 to use gpio-poweroff driver
ARM: mvebu: fix ReadyNAS 102 Power button GPIO to make it active high
Signed-off-by: Olof Johansson <olof@lixom.net>
Turn on SDHCI for i.MX support so machines can boot with local rootfs
on SD. Tested on a Wandboard Quad.
Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Pull two KVM fixes from Gleb Natapov.
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: VMX: do not check bit 12 of EPT violation exit qualification when undefined
ARM: kvm: rename cpu_reset to avoid name clash
When 5e12a613 and 0cd3754a were introduced, Netgear ReadyNAS 102 .dts
file was queued for inclusion and missed the update to have Mbus (and
then BootROM) ranges properties declared. It also missed the relocation
of Armada 370/XP PCIe DT nodes introduced by 14fd8ed0 after de1af8d4.
This patch fixes that which makes 3.12-rc3 bootable on the NAS.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Like we are doing on DDR0 we need to cleanly shutdown DDR1 if it is
used before rebooting.
If DDR1 is not initialized, we check it and avoid dereferencing its address.
Even by adding two more instructions, we are able to complete the procedure
within a single cache line.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
HWMOD removal for MMC is breaking edma_start as the events are being manually
triggered due to unused channel list not being clear.
The above issue is fixed by reading the "dmas" property from the DT node if it
exists and clearing the bits in the unused channel list if the dma controller
used by any device is EDMA. For this purpose we use the of_* helpers to parse
the arguments in the dmas phandle list.
Also introduced is a minor clean up of a checkpatch error in old code.
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Reported-by: Balaji T K <balajitk@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Nishanth Menon <nm@ti.com>
Cc: Pantel Antoniou <panto@antoniou-consulting.com>
Cc: Jason Kridner <jkridner@beagleboard.org>
Cc: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
On the TC2 testchip, when all CPUs in a cluster enter standbywfi
and commit a power down request, the power controller will wait
for standbywfil2 coming from L2 cache controller to shut the
cluster down.
By the time all CPUs in a cluster commit a power down request
and enter wfi, the power controller cannot backtrack, or put it
another way, a CPU must not be allowed to complete execution
independently of the power controller, the only way for it to
resume properly must be upon wake-up IRQ pending and subsequent
reset triggered from the power controller.
Current MCPM back-end for TC2 disables the GIC CPU IF only when
power down is committed through the tc2_pm_suspend() method, that
makes sense since a suspended CPU is still online and can receive
interrupts whereas a hotplugged CPU, since it is offline,
migrated all IRQs and shutdown the per-CPU peripherals, hence
their PPIs.
The flaw with this reasoning is the following. If all CPUs in
a clusters are entering a power down state either through CPU
idle or CPU hotplug, when the last man successfully completes
the MCPM power down sequence (and executes wfi), power controller
waits for L2 wfi signal to quiesce the cluster and shut it down.
If, when all CPUs are sitting in wfi, an online CPU hotplugs back
in one of the CPUs in the cluster being shutdown, that CPU
receives an IPI that causes wfi to complete (since tc2_pm_down()
method does not disable the GIC CPU IF in that case - CPU being
hotplugged out, not idle) and the power controller will never see
the stanbywfil2 signal coming from L2 that is required for
shutdown to happen and the system deadlocks.
Further to this issue, kexec hotplugs secondary CPUs out during
kernel reload/restart.
Because kexec may (deliberately) trash the old kernel text, it is
not OK for CPUs to follow the MCPM soft reboot path, since
instructions after the WFI may have been replaced by kexec.
If tc2_pm_down() does not disable the GIC cpu interface, there is a
race between CPU powerdown in the old kernel and the IPI from the
new kernel that triggers secondary boot, particularly if the
powerdown is slow (due to L2 cache cleaning for example). If the
new kernel wins the race, the affected CPU(s) will not really be
reset and may execute garbage after the WFI.
The only solution to this problem consists in disabling the GIC
CPU IF on a CPU committed to power down regardless of the power
down entry method (CPU hotplug or CPU idle). This way, CPU wake-up
is under power controller control, which prevents unexpected wfi
exit caused by a pending IRQ.
This patch moves the GIC CPU IF disable call in the TC2 MCPM
implementation from the tc2_pm_suspend() method to the
tc2_pm_down() method to fix the mentioned race condition(s).
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Tested-by: Dave Martin <Dave.Martin@arm.com> (for kexec)
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
* Remove unused #gpio-ranges-cells DT property
* Remove usage of deprecated #gpio-range-cells DT property
from GPIO R-Car
Property was deprecated in v3.11-rc2
* Correct ether pinctl naming for armadillo800eva board
Regression introduced in v3.10-rc5
* Add Micrel KSZ8041 PHY fixup to lager board
This resolves a problem that has been present since 3.11-rc2
* Update SDHI DT compatibility string to the <unit>-<soc> format
This makes compatibility strings consistent across all renesas
hardware which currently supports DT.
The bindings which are being updated where intorodiced on
a per-SoC basis starting in v3.8-rc7. They may have
been internally consistent when originally added.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=WVMt
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes4-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
From Simon Horman:
Fourth Round of Renesas ARM based SoC fixes for v3.12
* Remove unused #gpio-ranges-cells DT property
* Remove usage of deprecated #gpio-range-cells DT property
from GPIO R-Car
Property was deprecated in v3.11-rc2
* Correct ether pinctl naming for armadillo800eva board
Regression introduced in v3.10-rc5
* Add Micrel KSZ8041 PHY fixup to lager board
This resolves a problem that has been present since 3.11-rc2
* Update SDHI DT compatibility string to the <unit>-<soc> format
This makes compatibility strings consistent across all renesas
hardware which currently supports DT.
The bindings which are being updated where intorodiced on
a per-SoC basis starting in v3.8-rc7. They may have
been internally consistent when originally added.
* tag 'renesas-fixes4-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Remove #gpio-ranges-cells DT property
gpio: rcar: Remove #gpio-range-cells DT property usage
ARM: shmobile: armadillo: fixup ether pinctrl naming
ARM: shmobile: Lager: add Micrel KSZ8041 PHY fixup
ARM: shmobile: update SDHI DT compatibility string to the <unit>-<soc> format
Signed-off-by: Olof Johansson <olof@lixom.net>
the current dts is lacking interrupt and dma prop for video input
processor of prima2 and atlas6, this patch fixes it.
Signed-off-by: Renwei Wu <Renwei.Wu@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
we lost an address range <0x56000000 0x56000000 0x1b00000> for peri-iobg
of prima2.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Makefile missed to include atlas6-evb.dtb for ARCH_ATLAS6.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
sirf uart and usp-based uart driver with full dma support has
hit 3.12, here we fix the fifosize, dma channels for some HW
prop.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Without that fix, at the end of the shutdown process, the board is
still powered (led glowing, fan running, ...).
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
NETGEAR ReadyNAS 102 Power button definition in .dts file flags
associated GPIO active low instead of active high. This results
in reversed events reported by input subsystem (0 returned when
the button is pressed, 1 when released). This patch makes
associated GPIO active high to recover correct behaviour.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull scheduler, timer and x86 fixes from Ingo Molnar:
- A context tracking ARM build and functional fix
- A handful of ARM clocksource/clockevent driver fixes
- An AMD microcode patch level sysfs reporting fixlet
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
arm: Fix build error with context tracking calls
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: em_sti: Set cpu_possible_mask to fix SMP broadcast
clocksource: of: Respect device tree node status
clocksource: exynos_mct: Set IRQ affinity when the CPU goes online
arm: clocksource: mvebu: Use the main timer as clock source from DT
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode/AMD: Fix patch level reporting for family 15h
Pull ARM fixes from Russell King:
"Just a few relatively small ARM fixes found since the last merge
window, nothing too exciting"
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7837/3: fix Thumb-2 bug in AES assembler code
ARM: only allow kernel mode neon with AEABI
ARM: 7839/1: entry: fix tracing of ARM-private syscalls
ARM: 7836/1: add __get_user_unaligned/__put_user_unaligned
ad65782fba (context_tracking: Optimize main APIs off case
with static key) converted context tracking main APIs to inline
function and left ARM asm callers behind.
This can be easily fixed by making ARM calling the post static
keys context tracking function. We just need to replicate the
static key checks there. We'll remove these later when ARM will
support the context tracking static keys.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Anil Kumar <anilk4.v@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Kevin Hilman <khilman@linaro.org>
- removal of void IRQF_DISABLED flag in timer drivers
- two little fixes in DT for at91sam9x5 family
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJSQYrTAAoJEAf03oE53VmQ8n4IAIV0bJHRvpUQ9fGfMH3xoKuF
/Frb+HyPDQpPRPN3k6CaZSOa5P68d6WsC/Livw7HVcxwphI+BkCM4joHyeRCgH7G
RBbWPoscr1mKBZqha7s7+D5n9uxR5Zrxw2emlWnpoZCHpgaUcsZKaSYA1xbONO6o
OBlDffrXgf3vobepEFSLqYGHkQ5nyyegBJB6MLcFh7ceksOOb5cxT4G52Fan7T+U
JciaG8baO9WPKiMlcWpvFQ7Kys7zxqKzu1ILxolfUP8Rz+c/YAtb3pHsKrb6oo/D
lD+682L1sqaKtdYlnSiPM9rVEX929cwShcABt0Q5e//11uvVRG9AN/1Hh1rzMVs=
=bhiP
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes' of git://github.com/at91linux/linux-at91 into fixes
From Nicolas Ferre, first fixes series for 3.12:
- removal of void IRQF_DISABLED flag in timer drivers
- two little fixes in DT for at91sam9x5 family
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91: remove IRQF_DISABLED
ARM: at91: at91sam9x5: set default mmc[01] pinctrl-names
ARM: at91: serial: fix wrong pinctrl_usart2_rts
Signed-off-by: Olof Johansson <olof@lixom.net>
cpu_reset is already #defined in <asm/proc-fns.h> as processor.reset,
so it expands here and causes problems.
Cc: <stable@vger.kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
This property is no longer required by the GPIO binding. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
e5c9b4cd66 ("sh_eth: get R8A7740 support
out of #ifdef") exchanged sh-eth driver name to r8a7740-gether, but,
eva_pinctrl_map[] didn't follow it. Fixes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Patch 638591c enabled building the AES assembler code in Thumb2 mode.
However, this code used arithmetic involving PC rather than adr{l}
instructions to generate PC-relative references to the lookup tables,
and this needs to take into account the different PC offset when
running in Thumb mode.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This prevents the linker erroring with:
arm-linux-ld: error: arch/arm/lib/xor-neon.o uses VFP instructions, whereas arch/arm/lib/built-in.o does not
arm-linux-ld: failed to merge target specific data of file arch/arm/lib/xor-neon.o
This is due to the non-neon files being marked as containing FPA data/
instructions (even though they do not) being mixed with files which
contain VFP, which is an incompatible floating point format.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 377747c406 ("ARM: entry: allow ARM-private syscalls to be
restarted") reworked the low-level syscall dispatcher to allow
restarting of ARM-private syscalls. Unfortunately, this relocated the
label used to dispatch a private syscall from the trace path, so that
the invocation would be bypassed altogether!
This causes applications to fail under strace as soon as they rely on
a private syscall (e.g. set_tls):
set_tls(0xb6fad4c0, 0xb6fadb98, 0xb6fb1050, 0xb6fad4c0, 0xb6fb1050)
= -1 ENOSYS (Function not implemented)
This patch fixes the label so that we correctly dispatch private
syscalls from the trace path.
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently on the Lager board NFS timeouts/delays are seen when booting. That
turned out to happen because the SoC's ETH_LINK signal turns on and off after
each packet. It is connected to Micrel KSZ8041 PHY's LED0 signal. Ether LEDs
on the Lager board are named LINK and ACTIVE which corresponds to non-default
01 setting of the PHY control register 1 bits 14-15. The 'sh_eth' driver resets
the PHY when opening the network device, so we have to set the mentioned bits
back to 01 from the default 00 value which causes bouncing of ETH_LINK. That
can be achieved using the PHY platform fixup mechanism if we also modify the
driver to use it..
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Currently DT compatibility strings of both types can be found in the kernel
sources: <unit>-<soc> and <soc>-<unit>, whereas a unique format should be
followed and the former one is preferred. This patch converts the SDHI
MMC driver and its users to the common standard. This is safe for now, since
ATM no real products are using this driver with DT.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Chris Ball <cjb@laptop.org>
[Removed r8a7740.dtsi portion as it is not applicable]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Matt Porter