Add a device node for the L2 cache, and link the CPU node to it.
The L2 cache for the Cortex-A15 CPU cores is 1 MiB large (organized as
64 KiB x 16 ways).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables to use thermal-zone on r8a7793.
This thermal sensor can measure temperature from -40000 to 125000,
but over 117000 can be critical on this chip.
Thus, default critical temperature is now set as 115000 (this driver
is using 5000 steps) (Current critical temperature is using it as
90000, but there is no big reason about it)
And it doesn't check thermal zone periodically (same as current
behavior). You can exchange it by modifying polling-delay[-passive]
property.
You can set trip temp if your kernel has CONFIG_THERMAL_WRITABLE_TRIPS,
but you need to take care to use it, since it will call
orderly_poweroff() it it reaches to the value.
echo $temp > /sys/class/thermal/thermal_zone0/trip_point_0_temp
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device node for the external SCIF_CLK.
The presence of the SCIF_CLK crystal and its clock frequency depends on
the actual board.
Add the two optional clock sources (ZS_CLK and SCIF_CLK for the internal
resp. external clock) for the Baud Rate Generator for External Clock
(BRG) to all SCIF and HSCIF device nodes.
This increases the range and accuracy of supported baud rates on
(H)SCIF.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The clock is really the device functional clock, not the interface
clock. Rename it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable audio DMAC (= rcar-dmac) in r8a7793 device tree.
Based on similar work for the r8a7791 by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v4
* Use GIC_SPI in interrupts properties
Audio DMAC peri peri is no longer DMAEngine. it is supported by
sound driver. this patch enable it.
Base on work for the r8a7791 by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Instantiate the two Audio DMA controllers in the r8a7791 device tree.
Based on similar work for the r8a7791 by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Instantiate Audio DMA clocks in the r8a7791 device tree.
Based on similar work for the r8a7791 by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DVC support to sound node in r8a7793 device tree.
Based on similar work for the r8a7791 by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Instantiate R-Car sound node in r8a7793 device tree.
This only supports PIO transfers.
Based on similar work for the r8a7791 by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Declare m2 clock in r8a7793 device tree.
Based on similar work for the r8a7791 by Laurent Pinchart.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Instantiate audio clock in r8a7793 device tree.
audio_clk_a/b/c are required for R-Car sound.
Based on similar work for the r8a7791 by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Instantiate MSTP10 clocks in r8a7793 device tree.
Based on similar work for the r8a7791 by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use GIC_* defines for GIC interrupt cells in r8a7793 device tree.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Move dmac nodes in the r8a7793 device tree to match their location
in the r8a7791 device tree to aid comparison between the device
trees of these similar SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Instantiate all the 9 I2C controllers in the disabled state.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update IPMMU compat strings to include SoC part number.
By specifying SoC part number in DT it becomes possible
to implement SoC specific features in the IPMMU driver.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DMA properties to all SCIF, SCIFA, SCIFB, and HSCIF device nodes.
Based on similar work for the r8a7791 by Geert Uytterhoeven.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Instantiate all serial devices in r8a7793 device tree
and set them as disabled by default.
Based on similar work for the r8a7791 by Laurent Pinchart.
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commit a1bc260bb5 ("gpio: clean up gpio-ranges documentation")
declares the above property deprecated. That was more than 2 years ago.
Remove it, so it doesn't get copied around needlessly.
Based on similar work for the r8a7791 and r8a7794 by Wolfram Sang.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reported-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Add the DU device with a disabled state. Boards that want to enable the
DU need to specify the output topology.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use the new SoC specific binding for rcar-dmac and the generic
binding as a fall-back in the r8a7793 device tree.
In general Renesas hardware is not documented to the extent where the
relationship between IP blocks on different SoCs can be assumed although
they may appear to operate the same way. Furthermore the documentation
typically does not specify a version for individual IP blocks. For these
reasons a convention of using the SoC name in place of a version and
providing SoC-specific compat strings has been adopted.
Although not universally liked this convention is used in the bindings for
most drivers for Renesas hardware. The purpose of this patch is to
update the Renesas R-Car DMA Controller nodes to follow this convention.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add r8a7793 GPIO device nodes that are assumed to be identical
to r8a7791. This matches the data sheet for GPIO and MSTP bits.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Instantiate the QSPI controller in the r8a7793 device tree.
Based on similar work for the r8a7794 by Hisashi Nakamura and
Sergei Shtylyov.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Instantiate the two system DMA controllers in the r8a7793 device tree.
Based on similar work for the r8a7793 by Laurent Pinchart.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Instantiate the thermal sensor in the r8a7793 device tree.
Based on very similar work for the r8a7790 by Magnus Damm.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add IPMMU nodes for the r8a7793 SoC. The IPMMU configuration for r8a7793
is identical to r8a7791 and includes SY0, SY1, DS, MP, MX, RT and GP.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add an appropriate "#power-domain-cells" property to the cpg_clocks
device node, to create the CPG/MSTP Clock Domain.
Add "power-domains" properties to all device nodes for devices that are
part of the CPG/MSTP Clock Domain and can be power-managed through an
MSTP clock. This applies to most on-SoC devices, which have a
one-to-one mapping from SoC device to DT device node.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the "arm,cortex-a15-gic" compatible value for the GIC by
"arm,gic-400", as the R-Car Gen2 GIC is assumed to be a GIC-400.
This has been confirmed by reading the GICD_IIDR register (on r8a7791),
which reports 0x0200043b (GIC-400 = 0x02, ARM = 0x43b).
This has no effect on runtime behavior, as currently the GIC driver
treats both compatible values the same.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Minimal r8a7793 device tree including one CPU core, interrupt controllers,
timers, two serial ports, and the Ethernet controller, plus the required
clock descriptions.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Geert Uytterhoeven