ipw2100: Fix 'Driver using old /proc/net/wireless...' message
Wireless extensions moved the get_wireless_stats handler from being
in net_device into wireless_handler.
A prior instance of this patch resolved the issue for the ipw2200.
This one fixes it for the ipw2100.
Signed-off-by: Benoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change CONFIG_FEC_8XX to depend on CONFIG_8xx instead of CONFIG_FEC.
CONFIG_FEC depends on ColdFire CPUs, which does not apply for the
PPC 8xx processors.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hermas_bap_pread, hermes_bap_pwrite, and hermes_bap_pwrite_pad all have a parameter "len" that is declared unsigned,
but checked for a value less than zero. Auditing the callers, it is possible for len to be passed a negative value, so len should be an int.
Thanks to LinuxICC (http://linuxicc.sf.net)
Signed-off-by: Gabriel A. Devenyi <ace@staticwave.ca>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
In isl_38xx.c
In routine isl38xx_trigger-device
Move unnecessary udelay/register read.
This is only required when hand-compiling the driver and
setting VERBOSE > SHOW_ERROR_MESSAGES
Signed-off-by: Roger While <simrw@sim-basis.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This header file patch was missing from the recent SAA9730 patch.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
For the four versions of hardware that we (currently) support microcode
download on, the default configuration of our receive interrupt mitigation
microcode was too aggressive, and caused unnecessary delays when pinging,
and low(er) throughput on single connection latency sensitive performance
tests.
This code adds microcode support, and sets the defaults to more reasonable
settings. It also explains the functionality in the code in more detail.
Compile and load tested, shows expected behavior for slight delay of ping
packets (1-2ms) when ucode is loaded, and decent interrupt moderation for
small packets, while maintaining good throughput.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The smc91x driver relies upon register bank 2 being selected whenever
the interrupt handler is called. This isn't always so, especially if
we have a link change event during PHY configuration.
This results in register bank 0 being selected when the interrupt
handler is called, causing the wrong registers to be read for the
IRQ mask and status. In turn, this causes us to spin with a
permanently asserted IRQ.
The patch ensures that smc_phy_configure always exits with register
bank 2 selected.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Not only SMC_ACK_INT(IM_TX_EMPTY_INT) in in smc_hardware_send_pkt)
appears to be unnecessary (tested with an SMC91C94 and SMC91C111), but
it seems to trigger spurious interrupts on some machines as well.
Removed.
While at it, let's log any remaining spurious interrupts if any (and
clean usage of the max IRQ loop count value).
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add the missing NULL argument to the class_device_create calls.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
md needs to monitor the rate of requests to its devices when doing
resync/recovery so that it can back-off when there is non-resync IO. It
does this by comparing resync IO, which it counts, with total IO which is
taken from disk_stats.
disk_stats were recently changed to account sectors when a request
completes instead of when it is queued. This upsets md's calculations.
We could do the sync_io accounting at the end of requests too, but that has
problems. If an underlying device is an md array, the accounting will
still be done when the request is submitted. This could be changed for
some raid levels, but it cannot be changed for raid0 or linear without
substantial code changes.
So instead, we increase the error that is_mddev_idle allows, up to the
maximum amount of resync IO that can be in flight at any time. The
calculation is current fragile as each personality as different limits for
in-flight resync. This should be fixed up.
For now, this simple patch fixes the problem.
Increasing the error margin decreases the sensitivity to non-resync IO. To
partially compensate for this, the time to wait when non-resync IO is
detected is increased so that less steady IO is required to keep the resync
at bay.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some filesystems go oops.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The driver dependencies on PCI have been removed. This patch clears that
up in the Kconfig file
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use ioread8 and iowrite8 as suggested.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the necessary flush_schedule_work calls when canceling the timer.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On IPMI systems with BT interfaces, we don't start the kernel thread, so
smi_info->thread is NULL. Test for NULL when stopping the thread, because
kthread_stop() doesn't, and an oops ensues otherwise.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Properly clear the memory, and set "pr->flags.power" only if a C2 or
deeper state is valid (to make the code match both the comment and
previous behaviour).
This fixes a boot-time lockup reported by Maneesh Soni when using
"maxcpus=1".
Acked-by: Maneesh Soni <maneesh@in.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It was causing too many problems, and this is not the proper type of
driver for this device.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This lets us remove a lot of code in the drivers that were all checking
the same thing. It also found some bugs in a few of the drivers, which
has been fixed up.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix an error in the OHCI lh7a404 driver after the platform device
conversion.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This small patch adds a device ID used by older Maxtor OneTouch drives
(the ones with blue face-plate instead of the fancy silver one used in
newer models). The button on those drives works well with the current
driver.
From: Antti Andreimann <Antti.Andreimann@mail.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/usb/core/devio.c: In function `proc_ioctl_compat':
drivers/usb/core/devio.c:1401: warning: passing arg 1 of `compat_ptr' makes integer from pointer without a cast
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
this patch from Herbert Xu fixes a race by moving termination of
the URBs into close() exclusively.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Peter Favrholdt reported that his Kodak flash device was getting
detected as a CDROM, and he helped me track this down to the fact that
the device takes a long time (approx 440ms!) to reset.
This patch increases the delay to 500ms, which solves the problem.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
the scsi layer now uses very short sg lists. This breaks the microtek
driver. Here is a patch fixes this and some other issues.
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds two new Siemens mobiles IDs for the pl2303 driver.
Signed-off-by: Luiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The onetouch support doesn't suspend correctly (leaves an interrupt
URB posted, instead of unlinking it) so for now just disable it
when PM is in the air.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I actually have this device, and kernel reports blacklist entry is no
longer neccessary.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/usb/core/devio.c: In function `proc_ioctl_compat':
drivers/usb/core/devio.c:1401: warning: passing arg 1 of `compat_ptr' makes integer from pointer without a cast
NFI if this is correct...
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
People are complaining about a .old file in the tree. So rename
drivers/usb/serial/ChangeLog.old to ChangeLog.history.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes a slab corruption issue in the ipw2200 driver: it essentially
multiplied the error log number _twice_ by the size of the error element
entry (once explicitly in the code, and once implicitly as part of the
regular pointer arithmetic).
Cc: Henrik Brix Andersen <brix@gentoo.org>
Cc: Bernard Blackham <bernard@blackham.com.au>
Cc: Zilvinas Valinskas <zilvinas@gemtek.lt>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
--
Jeff Garzik