SFC9000-family boards do not all use MDIO PHYs, so we need a different
test for PHY aliveness.
Introduce a PHY operation test_alive(). For PHYs attached to Falcon,
use a common implementation based on the existing PHY MDIO test.
For PHYs managed through MCDI, use the appropriate MCDI request.
Change test name in ethtool from 'core mdio' to 'phy alive'.
Rename test_results::mdio to phy_alive and test_results::phy to phy_ext.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver has been mostly rewritten since Michael Brown's initial
work, so swap the order of the authors.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor PHY, MAC and NIC configuration operations so that the
existing link configuration can be re-pushed with:
efx->phy_op->reconfigure(efx);
efx->mac_op->reconfigure(efx);
and a new configuration with:
efx->nic_op->reconfigure_port(efx);
(plus locking and error-checking).
We have not held the link settings in software (aside from flow
control), and have relied on asking the hardware what they are. This
is a problem because in some cases the hardware may no longer be in a
state to tell us. In particular, if an entire multi-port board is
reset through one port, the driver bindings to other ports have no
chance to save settings before recovering.
We only actually need to keep track of the autonegotiation settings,
so add an ethtool advertising mask to struct efx_nic, initialise it
in PHY init and update it as necessary.
Remove now-unneeded uses of efx_phy_op::{get,set}_settings() and
struct ethtool_cmd.
Much of this was done by Steve Hodgson <shodgson@solarflare.com>.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the newly-added generic MDIO clause 45 support and remove
redundant definitions.
Add an 'efx_' prefix to the remaining driver-specific MDIO functions
and remove arguments which are redundant with efx->mdio.prtad.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shuffle bits of the OUI into the conventional written order.
Replace PHY id component macros with functions.
Zero-pad PHY id components in log messages.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All 10Xpress PHYs require autonegotiation all the time; enforce this
in the set_settings() method and do not treat it as a workaround.
Remove claimed support for 100M HD mode since it is not supported by
current firmware.
Do not set speed override bits when AN is enabled, and do not use
register 1.49192 for AN configuration as it can override what we set
elsewhere.
Always set the AN selector bits to 1 (802.3).
Fix confusion between Next Page and Extended Next Page.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add type codes for the new PHY and rename the SFX7101 type code.
Add definition of clause 22 extension MMD.
Adapt the 10Xpress SFX7101 code to support the SFT9001 as well.
Clean up register definitions.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add infrastructure for auto-negotiation of speed, duplex and flow
control.
When using 10Xpress, auto-negotiate flow control. While we're
at it, clean up the code to warn when partner is not 10GBASE-T
capable.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We often want to set or clear a flag in an MDIO register, but avoid
writing if no change is required since this can have side-effects.
Encapsulate this in a function, mdio_clause45_set_flag().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Combine DEVS0 and DEVS1 registers into a 32-bit mask instead of
reading just DEVS0.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add board monitoring to periodic work whenever link is down.
For SFE4001, report when a fault has caused the PHY to turn off.
For SFE4002, switch XFP PHY into low-power state in case of a fault.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Replace (cond ? 1 : 0) with cond or !!cond as appropriate, and
(cond ? 0 : 1) with !cond.
Remove some redundant boolean temporaries.
Rename one field that looks like a flag but isn't.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This was making noise during 10Xpress self-test.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add a set of self-tests accessible thorugh ethtool.
Add hardware loopback and TX disable control code to support them.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The driver supports the 10Xpress PHY and XFP modules on our reference
designs SFE4001 and SFE4002 and the SMC models SMC10GPCIe-XFP and
SMC10GPCIe-10BT.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ben Hutchings