And put the pfit stuff into substructs while we're at it.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This gets the panel fitter working on eDP on VLV, and should also apply
to eDP panels on G4x chipsets (if we ever detect and mark an all-in-one
panel as eDP anyway).
A few cleanups are still possible on top of this, for example the LVDS
border control could be placed in the LVDS encoder structure and updated
based on the result of the panel fitter calculation.
Multi-pipe fitting isn't handled correctly either if we ever get a config
that wants to try the panel fitter on more than one output at a time.
v2: use pipe_config for storing pfit values (Daniel)
add i9xx_pfit_enable function for use by 9xx and VLV (Daniel)
v3: fixup conflicts and lvds_dither check
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: fix up botched conflict resolution from Jesse:
- border = LVDS_BORDER_ENABLE was lost for CENTER scaling
- comment about gen2/3 panel fitter scaling was lost
- dev_priv->lvds_dither reintroduced.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Up to now we've relied on the bios to get this right for us. Let's try
out whether our code has improved a bit, since we should dither
always when the output bpp doesn't match the plane bpp.
- gen5+ should be fine, since we only use the bios hint as an upgrade.
- gen4 changes, since here dithering is still controlled in the lvds
register.
- gen2/3 has implicit dithering depeding upon whether you use 2 or 3
lvds pairs (which makes sense, since it only supports 8bpc pipe
outpu configurations).
- hsw doesn't support lvds.
v2: Remove redudant dither setting.
v3: Completly drop reliance on dev_priv->lvds_dither.
v4: Enable dithering on gen2/3 only when we have a 18bpp panel, since
up-dithering to a 24bpp panel is not supported by the hw. Spotted by
Ville.
v5: Also only enable lvds port dithering on gen4 for 18bpp modes. In
practice this only excludes dithering a 10bpc plane down for a 24bpp
lvds panel. Not something we truly care about. Again noticed by Ville.
v6: Actually git add.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In preparation of adding locking to backlight, make max backlight value
(the modulation frequency the PWM duty cycle value must not exceed)
internal to intel_panel.c.
Have intel_panel_set_backlight() accept a caller defined range for level,
and scale input to max backlight value internally.
Clean up intel_panel_get_max_backlight() and usage internally.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows unifying a bunch of the PLL calculations and whatnot.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In this commit we enable both CPU and PCH FIFO underrun reporting and
start reporting them. We follow a few rules:
- after we receive one of these errors, we mask the interrupt, so
we won't get an "interrupt storm" and we also won't flood dmesg;
- at each mode set we enable the interrupts again, so we'll see each
message at most once per mode set;
- in the specific places where we need to ignore the errors, we
completely mask the interrupts.
The downside of this patch is that since we're completely disabling
(masking) the interrupts instead of just not printing error messages,
we will mask more than just what we want on IVB/HSW CPU interrupts
(due to GEN7_ERR_INT) and on CPT/PPT/LPT PCHs (due to SERR_INT). So
when we decide to mask PCH FIFO underruns for pipe A on CPT, we'll
also be masking PCH FIFO underruns for pipe B, because both are
reported by SERR_INT, which has to be either completely enabled or
completely disabled (in othe words, there's no way to disable/enable
specific bits of GEN7_ERR_INT and SERR_INT).
V2: Rename some functions and variables, downgrade messages to
DRM_DEBUG_DRIVER and rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In Valleyview voltage swing, pre-emphasis and lane control registers can
be programmed only through the h/w side band fabric. Update
vlv_update_pll, i9xx_crtc_enable, and intel_enable_pll with the
appropriate programming.
We need to make sure that the tx lane reset occurs in both the full mode
set and DPMS paths, so factor things out to allow that.
v2: use different DPIO_DIVISOR values for VGA and DisplayPort
v3: Fix update pll logic to use same DPIO_DIVISOR & DPIO_REFSFR values
for all display interfaces
v4: collapse with various updates
v5: squash with crtc enable/pll enable bits
v6: split out DP code (jbarnes)
put phyready check under IS_VALLEYVIEW (jbarnes)
remove unneeded check in 9xx pll div update (Jani)
wrap VLV pll update call in IS_VALLEYVIEW (Jani)
move port enable back to end of crtc enable (jbarnes)
put phyready check under IS_VALLEYVIEW (jbarnes)
v7: fix up conflicts against latest drm-intel-next-queued
v8: use DPIO reg names, fix pipes (Jani)
from mPhy_registers_VLV2_ww20p5 doc
v9: update to latest info from driver enabling notes doc
driver_vbios_notes_9
v10: fixup a bit of pipe/port confusion to allow eDP and HDMI to work
simultaneously (Jesse)
v11: use pll/port callbacks for DPIO port activity (Daniel)
use separate VLV CRTC enable function (Daniel)
move around port ready checks (Jesse)
Signed-off-by: Pallavi G <pallavi.g@intel.com>
Signed-off-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Gajanan Bhat <gajanan.bhat@intel.com>
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Drop pfit changes and add a little comment explaining that
vlv has a different enable sequence and so needs it's own crtc_enable
callback. Also apply a fixup patch from Wu Fengguang to shut up some
compiler warnings.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Program few Tx buffer Swing control settings through DPIO.
v2: fix up codingstyle (Daniel)
call from set_signal_levels (Ville, Daniel)
use proper port numbers (Jesse)
Signed-off-by: Pallavi G <pallavi.g@intel.com>
Signed-off-by: Yogesh M <yogesh.mohan.marimuthu@intel.com>
Signed-off-by: Gajanan Bhat <gajanan.bhat@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v2 changes)
[danvet: Reorder if-ladder to avoid two IS_VLV checks.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For a bunch of reason we need to more accurately track this:
- hw pipe state readout for Haswell needs the cpu transcoder.
- We need to know the right cpu transcoder in a bunch of places in
->disable and other modeset callbacks.
In the future we need to add hw state readout&check support, too. But
to avoid ugly merge conflicts do the rote sed job now without any
functional changes.
v2: Preserve the cpu_transcoder value when overwriting crtc->config.
Reported by Paulo.
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
[danvet: Removed rough whitespace that Chris spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When an encoder is shared on several connectors there is only
one hotplug line, thus this line needs to be shared among these
connectors.
If HPD detect only works reliably on a subset of those connectors,
we want to poll the others. Thus we need to make sure that storm
detection doesn't mess up the settings for those connectors.
Therefore we store the settings in the intel_connector struct and
restore them from there.
If nothing is set but the encoder has a hpd_pin set we assume this
connector is hotplug capable.
On init/reset we make sure the polled state of the connectors
is (re)set to the default value, the HPD interrupts are marked
enabled.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It returns true if we've requested to turn the power well on and it's
really on. It also returns true for all the previous gens.
For now there's just one caller, but I'm going to add more.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Clock computations and handling are highly encoder specific, both in
the optimal clock selection and also in which clocks to use and when
sharing of clocks is possible.
So the best place to do this is somewhere in the encoders, with a
generic fallback for those encoders without special needs. To facility
this, add a pipe_config->clocks_set boolean.
This patch here is only prep work, it simply sets the computed clock
values in pipe_config->dpll, and uses that data in the hw clock
setting functions.
Haswell code isn't touched, simply because Haswell clocks work much
different and need their own infrastructure (with probably a
Haswell-specific config->ddi_clock substruct).
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jesse Barnes noticed in his review of my DP cleanup series that
intel_edp_target_clock is now unused. Checking related code I've
noticed that also intel_edp_link_config is long unused.
Kill them both.
Wrt leaky eDP functions used in the common crtc code, the only thing
still left is intel_encoder_is_pch_edp. That one is just due to the
massive confusion between eDP vs. DP and port A vs. port D. Crtc code
should at most concern itself with the later, never with the former.
But that's material for another patch series.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need it in the fdi m_n computation, which nicely kills almost
all ugly special cases in there.
It looks like we also need this to handle 12bpc hdmi correctly.
Eventually it might be better to switch things around and put the
target clock into adjusted_mode->clock and create a new pipe_config
parameter for the port link clock.
v2: Add a massive comment in the code to explain this mess.
v3: s/dp_target_clock/pixel_target_clock in anticipation of the hdmi
use-case.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need a flag to designate dp encoders and the dp link m_n parameters
in the pipe config for that. And now that the pipe bpp computations
have been moved up and stored in the pipe config, too, we can do this
without losing our sanity.
v2: Rebased on top of Takashi Iwai's fix to (again) fix the target
clock handling for eDP. Luckily the new code is sane enough and just
does the right thing!
v3: Move ->has_dp_encoder to this patch (Jesse).
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's a rather decent confusion going on around transcoder m_n
values. So let's clarify:
- All dp encoders need this, either on the pch transcoder if it's a
pch port, or on the cpu transcoder/pipe if it's a cpu port.
- fdi links need to have the right m_n values for the fdi link set in
the cpu transcoder.
To handle the pch vs transcoder stuff a bit better, extract transcoder
set_m_n helpers. To make them simpler, set intel_crtc->cpu_transcoder
als in ironlake_crtc_mode_set, so that gen5+ (where the cpu m_n
registers are all at the same offset) can use it.
Haswell modeset is decently confused about dp vs. edp vs. fdi. dp vs.
edp works exactly the same as dp (since there's no pch dp any more),
so use that as a check. And only set up the fdi m_n values if we
really have a pch encoder present (which means we have a VGA encoder).
On ilk+ we've called ironlake_set_m_n both for cpu_edp and for pch
encoders. Now that dp_set_m_n handles all dp links (thanks to the
pch encoder check), we can ditch the cpu_edp stuff from the
fdi_set_m_n function.
Since the dp_m_n values are not readily available, we need to
carefully coax the edp values out of the encoder. Hence we can't (yet)
kill this superflous complexity.
v2: Rebase on top of the ivb fdi B/C check patch - we need to properly
clear intel_crtc->fdi_lane, otherwise those checks will misfire.
v3: Rebased on top of a s/IS_HASWELL/HAS_DDI/ patch from Paulo Zanoni.
v4: Drop the addition of has_dp_encoder, it's in the wrong patch (Jesse).
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No constant alpha yet though, that needs a new ioctl and/or property to
get/set.
v2: use drm_plane_format_cpp (Ville)
fix up vlv_disable_plane, remove IVB bits (Ville)
remove error path rework (Ville)
fix component order confusion (Ville)
clean up platform init (Ville)
use compute_offset_xtiled (Ville)
v3: fix up more format confusion (Ville)
update to new page offset function (Ville)
v4: remove incorrect formats from framebuffer_init (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As Thomas Gleixner spotted, it's rather horrible racy:
- We can miss almost a full tick, so need to compensate by 1 jiffy.
- We need to re-check the condition when having timed-out, since a
the last check could have been before the timeout expired. E.g. when
we've been preempted or a long irq happened.
Cc: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Jack Winter <jbh@alchemy.lu>
Cc: Jack Winter <jbh@alchemy.lu>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since
commit bcf9dcc1e6
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Sun Jul 15 09:42:38 2012 +0100
drm/i915: Workaround hang with BSD and forcewake on SandyBridge
and
commit 0cc2764cc4
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Sat Sep 1 22:59:48 2012 -0700
drm/i915: use cpu_relax() in wait_for_atomic
these two macros are essentially the same, so unify them. We keep the
_us version since it's a nice documentation for smaller timeouts.
v2: Fixup time unit conversion, _wait_for takes ms (Ville).
Cc: Jack Winter <jbh@alchemy.lu>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The old code only handled either 6bpc or 8bpc. Since it's easy to do,
reorganize the code to be a bit more generic so that it can also handle
10bpc and 12bpc. Note that we still start with 8bpc, so there's no
functional change.
Also, since we no don't need to compute the 6BPC flag in the mode_valid
callback, we can consolidate things a bit. That requires though that
the link bw computation is moved up in the compute_config callback.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to compute this earlier. To avoid a big complicated patch,
this patch here just does the big search&replace and still calls the
old functions at the same places.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we have a useful struct for this, let's use it. Some neat
pointer-chasing required, but it's all there already.
v2: Rebased on top of the added Haswell limited color range support.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is used way too often in the enable/disable paths. And will
be even more useful in the future.
Note that correct semantics of this change highly depend upon
correct updating of intel_crtc->config: Like with all other
modeset state, we need to call ->disable with the old config,
but ->mode_set and ->enable with the new config.
v2: Do not yet use the flag in the ->disable callbacks - atm we don't
yet have support for the information stored in the pipe_config in the
hw state readout code, so this will be wrong at boot-up/resume.
v3: Rebased on top of the hdmi/dp ddi encoder merging.
v4: Fixup stupid rebase error which lead to a NULL vfunc deref.
v5: On haswell the VGA port is on the PCH!
v6: s/IS_HASWELL/HAS_DDI/, spotted by Paulo Zanoni. Also add a missing
parameter name in a function declaration.
v7: Don't forget to git add ...
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Used by SDVO (and hopefully, eventually HDMI, if we ever get around
to fixing up the low dotclock CEA modes ...).
This required adding a new encoder->mode_set callback to be able to
pass around the intel_crtc_config.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only used by the lvds encoder. Note that we shouldn't do the same
simple conversion with the FORCE_6BPC flag, since that's much better
handled by moving all the pipe_bpc computation around.
This requires that we pass the pipe config around to encoders, so
that they can set special attributes and set constraints. To do so
introduce a new ->compute_config encoder callback, which is called in
stead of the drm crtc helper's ->mode_fixup.
To avoid massive churn all over the codebase we don't want to convert
all existing ->mode_fixup functions. Instead I've opted to convert
them on an as-needed basis (mostly to cut down on rebase conflicts and
to have more freedom to experiment around while developing the
patches).
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently only containing the requested and the adjusted mode. And
only crtc callbacks are converted somewhat to it, encoders will be
done on a as-needed basis (simply too much churn in one patch
otherwise).
Future patches will add tons more useful stuff to this struct,
starting with the very simple.
v2: Store the pipe_config in the intel_crtc, so that the ->mode-set,
->enable and also ->disable have easy access to it.
v3: Store the pipe config in the right crtc ...
v4: Rebased.
v5: Fixup an OOPS when trying to kfree an ERR_PTR.
v6: Used drm_moode_copy and some other small cleanups as suggested
by Ville Syrjälä.
v7: drm_mode_copy preserves the mode id of the destination, so no need
to clear it again (Ville).
v8: Break a long line spotted by Paulo.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To clean up hotplug support we add a new enum to intel_encoder:
enum hpd_pin. It allows the encoder to request a hpd line but leave
the details which IRQ is responsible on which chipset generation
to i915_irq.c.
This way requesting hotplug support will become really simple on
the encoder/connector level.
Signed-off-by: Egbert Eich <eich@suse.de>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To be used to restore sprite state on resume.
v2: move sprite tracking bits up so we don't track modified sprite state
v3: use src_x/y in sprite suspend/resume code (Ville)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We are really talking about the transcoder function here and the disable
version uses trancoder in its name already, so let's try to be
consistent.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRRkrbAAoJEHm+PkMAQRiGy3oH/jrbHinYs0auurANgx4TdtWT
/WNajstKBqLOJJ6cnTR7sOqwOVlptt65EbbTs+qGyZ2Z2W/Lg0BMenHvNHo4ER8C
e7UbMdBCSLKBjAMKh1XCoZscGv4Exm8WRH3Vc5yP0Hafj3EzSAVLY1dta9WKKoQi
bh7D1ErUlbU1zczA1w5YbPF0LqFKRvyZOwebMCCAKAxv5wWAxmbcPNxVR4sufkjg
k6TkQ2ysgWivZAfy3tJYOcxiEu7ahpZVEuYdlZEJQXHRQUfoNljQlOp4BqKsYUai
5A0kaf2VpKay/7pkhvTfBBcF/jFJ68pYP6gQ2ThNdr0b5kOiAfMWj030Xyngnhg=
=iO9t
-----END PGP SIGNATURE-----
Merge tag 'v3.9-rc3' into drm-intel-next-queued
Backmerge so that I can merge Imre Deak's coalesced sg entries fixes,
which depend upon the new for_each_sg_page introduce in
commit a321e91b6d
Author: Imre Deak <imre.deak@intel.com>
Date: Wed Feb 27 17:02:56 2013 -0800
lib/scatterlist: add simple page iterator
The merge itself is just two trivial conflicts:
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Two regressions fixes from snowboarding land
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Revert hdmi HDP pin checks
drm/i915: Handle untiled planes when computing their offsets
We trim the fb to fit the CRTC by computing the offset of that CRTC to
its nearest tile_row origin. This allows us to use framebuffers that are
larger than the CRTC limits without additional work.
However, we failed to compute the offset for a linear framebuffer
correctly as we treated its x-advance in whole tiles (instead of the
linear increment expected), leaving the CRTC misaligned with its
contents.
Fixes regression from commit c2c7513124
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jul 5 12:17:30 2012 +0200
drm/i915: adjust framebuffer base address on gen4+
v2: Adjust relative x-coordinate after linear alignment (vsyrjala)
v3: Repaint with pokadots (vsyrjala)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=61152
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So here's my promised pile of fixes for 3.9. I've dropped the core prep
patches for vt-switchless suspend/resume as discussed on irc. Highlights:
- Fix dmar on g4x. Not really gfx related, but I'm fed up with getting
blamed for dmar crapouts.
- Disable wc ptes updates on ilk when dmar is enabled (Chris). So again,
dmar, but this time gfx related :(
- Reduced range support for hsw, using the pipe CSC (Ville).
- Fixup pll limits for gen3/4 (Patrick Jakobsson). The sdvo patch is
already confirmed to fix 2 bug reports, so added cc: stable on that one.
- Regression fix for 8bit fb console (Ville).
- Preserve lane reversal bits on DDI/FDI ports (Damien).
- Page flip vs. gpu hang fixes (Ville). Unfortuntely not quite all of
them, need to decide what to do with the currently still in-flight ones.
- Panel fitter regression fix from Mika Kuoppala (was accidentally left on
on some pipes with the new modset code since 3.7). This also improves
the modeset sequence and might help a few other unrelated issues with
lvds.
- Write backlight regs even harder ... another installement in our eternal
fight against the BIOS and backlights.
- Fixup lid notifier vs. suspend/resume races (Zhang Rui). Prep work for
new ACPI stuff, but closing the race itself seems worthwile on its own.
- A few other small fixes and tiny cleanups all over.
Lots of the patches are cc: stable since I've stalled on a few
not-so-important fixes for 3.8 due to the grumpy noise Linus made.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel: (33 commits)
intel/iommu: force writebuffer-flush quirk on Gen 4 Chipsets
drm/i915: Disable WC PTE updates to w/a buggy IOMMU on ILK
drm/i915: Implement pipe CSC based limited range RGB output
drm/i915: inverted brightness quirk for Acer Aspire 4736Z
drm/i915: Print the hw context status is debugfs
drm/i915: Use HAS_L3_GPU_CACHE in i915_gem_l3_remap
drm/i915: Fix PIPE_CONTROL DW/QW write through global GTT on IVB+
drm/i915: Set i9xx sdvo clock limits according to specifications
drm/i915: Set i9xx lvds clock limits according to specifications
drm/i915: Preserve the DDI link reversal configuration
drm/i915: Preserve the FDI line reversal override bit on CPT
drm/i915: add missing \n to UTS_RELEASE in the error_state
drm: Use C8 instead of RGB332 when determining the format from depth/bpp
drm: Fill depth/bits_per_pixel for C8 format
drm/i915: don't clflush gem objects in stolen memory
drm/i915: Don't wait for page flips if there was GPU reset
drm/i915: Kill obj->pending_flip
drm/i915: Fix a typo in a intel_modeset_stage_output_state() comment
drm/i915: remove bogus mutex_unlock from error-path
drm/i915: Print the pipe control page GTT address
...
Some (but not all) of the HDMI registers can be used to control sDVO,
so those registers have two names. IMHO, when we're talking about
HDMI, we really should call the HDMI control register "hdmi_reg"
instead of "sdvox_reg", otherwise we'll just confuse people reading
our code (we now have platforms with HDMI but without SDVO). So now
"struct intel_hdmi" has a member called "hdmi_reg" instead of
"sdvox_reg".
Also, don't worry: "struct intel_sdvo" still has a member called
"sdvo_reg".
v2: Rebase (v1 was sent in May 2012).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This way we can remove some duplicated code and avoid more mistakes
and regressions with these registers in the future.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GPU reset will drop all flips that are still in the ring. So after the
reset, call update_plane() for all CRTCs to make sure the primary
planes are scanning out from the correct buffer.
Also finish all pending flips. That means user space will get its
page flip events and won't get stuck waiting for them.
v2: Explicitly finish page flips instead of relying on FLIP_DONE
interrupt being generated by the base address update.
v3: Make two loops over crtcs to avoid deadlocks with the crtc mutex
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Fixup long line complaint from checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similarly to:
commit 6a0d1df3d3a0d2370541164eb0595fe35dcd6de3
Author: Damien Lespiau <damien.lespiau@intel.com>
Date: Tue Dec 11 15:18:28 2012 +0000
drm/i915: Preserve the FDI line reversal override bit on CPT
DDI port support lane reversal to easy the PCB layouting work. Let's
preserve the bit configured by the BIOS (until we find how to correctly
retrieve the information from the VBT, but this does sound more fragile
then just relying on the BIOS that has, hopefully, been validated
already.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If a GPU reset occurs while a page flip has been submitted to the ring,
the flip will never complete once the ring has been reset.
The GPU reset can be detected by sampling the reset_counter before the
flip is submitted, and then while waiting for the flip, the sampled
counter is compared with the current reset_counter value.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Move the reset_counter assignment to an earlier place in
common code as discussed on the mailing list.]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=60140
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the driver is in control of whether it needs to disable
everything at take-over or not, we can rip this all out.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When adding the fb idle detection to mark-inactive, it was forgotten
that userspace can drive the processing of retire-requests. We assumed
that it would be principally driven by the retire requests worker,
running once every second whilst active and so we would get the deferred
timer for free. Instead we spend too many CPU cycles reclocking the LVDS
preventing real work from being done.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Alexander Lam <lambchop468@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=58843
Cc: stable@vger.kernel.org
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our suspend code touches a lot of registers all over the place, so we
need to enable the power well before suspending.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Fixup compilation by stealing the header decl from the
dynamic power wells patch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The current code was wrong in many different ways, so this is a full
rewrite. We don't have "different power wells for different parts of
the GPU", we have a single power well, but we have multiple registers
that can be used to request enabling/disabling the power well. So
let's be a good citizen and only use the register we're suppose to
use, except when we're loading the driver, where we clear the request
made by the BIOS.
If any of the registers is requesting the power well to be enabled, it
will be enabled. If none of the registers is requesting the power well
to be enabled, it will be disabled.
For now we're just forcing the power well to be enabled, but in the
next commits we'll change this.
V2:
- Remove debug messages that could be misleading due to possible
race conditions with KVMr, Debug and BIOS.
- Don't wait on disabling: after a conversaion with a hardware
engineer we discovered that the "restriction" on bit 31 is just
for the "enable" case, and we don't even need to wait on the
"disable" case.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ELD info should be updated dynamically according to hot plug event.
For haswell chip, clear/set the eld valid bit and output enable bit
from callback intel_disable/eanble_ddi().
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Wang Xingchao <xingchao.wang@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The AVI infoframe is able to inform the display whether the source is
sending full or limited range RGB data.
As per CEA-861 [1] we must first check whether the display reports the
quantization range as selectable, and if so we can set the approriate
bits in the AVI inforframe.
[1] CEA-861-E - 6.4 Format of Version 2 AVI InfoFrame
v2: Give the Q bits better names, add spec chapter information
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a new "Automatic" mode to the "Broadcast RGB" range property.
When selected the driver automagically selects between full range and
limited range output.
Based on CEA-861 [1] guidelines, limited range output is selected if the
mode is a CEA mode, except 640x480. Otherwise full range output is used.
Additionally DVI monitors should most likely default to full range
always.
As per DP1.2a [2] DisplayPort should always use full range for 18bpp, and
otherwise will follow CEA-861 rules.
NOTE: The default value for the property will now be "Automatic"
so some people may be affected in case they're relying on the
current full range default.
[1] CEA-861-E - 5.1 Default Encoding Parameters
[2] VESA DisplayPort Ver.1.2a - 5.1.1.1 Video Colorimetry
v2: Use has_hdmi_sink to check if a HDMI monitor is present
v3: Add information about relevant spec chapters
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The RGB color range select bit on the DP/SDVO/HDMI registers
disappeared when PCH was introduced, and instead a new PIPECONF bit
was added that performs the same function.
Add a new INTEL_MODE_LIMITED_COLOR_RANGE private mode flag, and set
it in the encoder mode_fixup if limited color range is requested.
Set the the PIPECONF bit 13 based on the flag.
Experimentation showed that simply toggling the bit while the pipe is
active doesn't work. We need to restart the pipe, which luckily already
happens.
The DP/SDVO/HDMI bit 8 is marked MBZ in the docs, so avoid setting it,
although it doesn't seem to do any harm in practice.
TODO:
- the PIPECONF bit too seems to have disappeared from HSW. Need a
volunteer to test if it's just a documentation issue or if it's really
gone. If the bit is gone and no easy replacement is found, then I suppose
we may need to use the pipe CSC unit to perform the range compression.
v2: Use mode private_flags instead of intel_encoder virtual functions
v3: Moved the intel_dp color_range handling after bpc check to help
later patches
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=46800
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
- seqno wrap fixes and debug infrastructure from Mika Kuoppala and Chris
Wilson
- some leftover kill-agp on gen6+ patches from Ben
- hotplug improvements from Damien
- clear fb when allocated from stolen, avoids dirt on the fbcon (Chris)
- Stolen mem support from Chris Wilson, one of the many steps to get to
real fastboot support.
- Some DDI code cleanups from Paulo.
- Some refactorings around lvds and dp code.
- some random little bits&pieces
* tag 'drm-intel-next-2012-12-21' of git://people.freedesktop.org/~danvet/drm-intel: (93 commits)
drm/i915: Return the real error code from intel_set_mode()
drm/i915: Make GSM void
drm/i915: Move GSM mapping into dev_priv
drm/i915: Move even more gtt code to i915_gem_gtt
drm/i915: Make next_seqno debugs entry to use i915_gem_set_seqno
drm/i915: Introduce i915_gem_set_seqno()
drm/i915: Always clear semaphore mboxes on seqno wrap
drm/i915: Initialize hardware semaphore state on ring init
drm/i915: Introduce ring set_seqno
drm/i915: Missed conversion to gtt_pte_t
drm/i915: Bug on unsupported swizzled platforms
drm/i915: BUG() if fences are used on unsupported platform
drm/i915: fixup overlay stolen memory leak
drm/i915: clean up PIPECONF bpc #defines
drm/i915: add intel_dp_set_signal_levels
drm/i915: remove leftover display.update_wm assignment
drm/i915: check for the PCH when setting pch_transcoder
drm/i915: Clear the stolen fb before enabling
drm/i915: Access to snooped system memory through the GTT is incoherent
drm/i915: Remove stale comment about intel_dp_detect()
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Note: This patch also adds a little helper intel_crtc_restore_mode for
the common case where we do a full modeset but with the same
parameters, e.g. to undo bios damage or update a property.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Added note.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If you unplug the hdmi connector slowly enough, the hotplug interrupt
fires but then the kernel code tries to read the EDID and succeeds
(because the connector is still half connected, the HPD pin is shorter
than the others, and DDC works). Since EDID succeeds it thinks the
monitor is still connected.
To prevent that, read the live HPD status in the hotplug handler before
trying to read the EDID.
v2: Rename the function to ibx_ (Chris Wilson)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=55372
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For GMCH platforms we set up the hpd irq registers in the irq
postinstall hook. But since we only enable the irq sources we actually
need in PORT_HOTPLUG_EN/STATUS, taking dev_priv->hotplug_supported_mask
into account, no hpd interrupt sources is enabled since
commit 52d7ecedac
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sat Dec 1 21:03:22 2012 +0100
drm/i915: reorder setup sequence to have irqs for output setup
Wrongly set-up interrupts also lead to broken hw-based load-detection
on at least GM45, resulting in ghost VGA/TV-out outputs.
To fix this, delay the hotplug register setup until after all outputs
are set up, by moving it into a new dev_priv->display.hpd_irq_callback.
We might also move the PCH_SPLIT platforms to such a setup eventually.
Another funny part is that we need to delay the fbdev initial config
probing until after the hpd regs are setup, for otherwise it'll detect
ghost outputs. But we can only enable the hpd interrupt handling
itself (and the output polling) _after_ that initial scan, due to
massive locking brain-damage in the fbdev setup code. Add a big
comment to explain this cute little dragon lair.
v2: Encapsulate all the fbdev handling by wrapping the move call into
intel_fbdev_initial_config in intel_fb.c. Requested by Chris Wilson.
v3: Applied bikeshed from Jesse Barnes.
v4: Imre Deak noticed that we also need to call intel_hpd_init after
the drm_irqinstall calls in the gpu reset and resume paths - otherwise
hotplug will be broken. Also improve the comment a bit about why
hpd_init needs to be called before we set up the initial fbdev config.
Bugzilla: Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=54943
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v3)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jesse Barnes