If USB cable is connected prior to boot, we don't get any interrupts
so we must manually check the VBUS state and report it during probe.
If we don't do it then USB controller will never know that peripheral
cable was connected till the user unplugs and replugs the cable.
Fixes: b7aad8e268 ("extcon: palmas: Add the support for VBUS detection by using GPIO")
Cc: stable@vger.kernel.org
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Palmas extcon IRQs are nested threaded and wired to the Palmas
interrupt controller. So, this flag is not required for nested
IRQs anymore, since commit 3c646f2c6a ("genirq: Don't suspend
nested_thread irqs over system suspend") was merged. However, the
fix in commit ae64e42cc2 ("extcon: palmas: Drop IRQF_EARLY_RESUME
flag") missed a stray flag causing the following crash on resume on
BeagleBoard-X15 platform:
[ 53.670141] Unhandled fault: imprecise external abort (0x1406) at 0x00000000
[..]
[ 53.670141] [<c04ae734>] (omap_set_gpio_triggering) from [<c04aeb94>] (omap_gpio_unmask_irq+0xc0/0xc4)
[ 53.670141] [<c04aeb94>] (omap_gpio_unmask_irq) from [<c01a0b88>] (irq_enable+0x30/0x44)
[ 53.670141] [<c01a0b88>] (irq_enable) from [<c019ebd8>] (__enable_irq+0x54/0x78)
[ 53.670141] [<c019ebd8>] (__enable_irq) from [<c01a4e60>] (resume_irqs+0xe8/0x100)
[ 53.670141] [<c01a4e60>] (resume_irqs) from [<c0514840>] (syscore_resume+0x94/0x298)
[ 53.670141] [<c0514840>] (syscore_resume) from [<c01981cc>] (suspend_devices_and_enter+0x790/0x9e4)
[ 53.670141] [<c01981cc>] (suspend_devices_and_enter) from [<c0198a60>] (pm_suspend+0x640/0x75c)
[ 53.670141] [<c0198a60>] (pm_suspend) from [<c0196bec>] (state_store+0x64/0xb8)
[ 53.670141] [<c0196bec>] (state_store) from [<c0307944>] (kernfs_fop_write+0xc0/0x1bc)
[ 53.670141] [<c0307944>] (kernfs_fop_write) from [<c028acb0>] (__vfs_write+0x1c/0xd8)
[ 53.670141] [<c028acb0>] (__vfs_write) from [<c028bba0>] (vfs_write+0x90/0x16c)
[ 53.670141] [<c028bba0>] (vfs_write) from [<c028c8c0>] (SyS_write+0x44/0x9c)
[ 53.670141] [<c028c8c0>] (SyS_write) from [<c0107840>] (ret_fast_syscall+0x0/0x1c)
[..]
Fixes: ae64e42cc2 ("extcon: palmas: Drop IRQF_EARLY_RESUME flag")
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Roger Quadros <rogerq@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Palams extcon IRQs are nested threaded and wired to the Palmas
inerrupt controller. So, this flag is not required for nested irqs
anymore, since commit 3c646f2c6a ("genirq: Don't suspend
nested_thread irqs over system suspend") was merged.
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Roger Quadros <rogerq@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch support for VBUS detection by using GPIO pin.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
With commit b17d1bf16c ("gpio: make flags mandatory for gpiod_get functions")
it becomes necessary to pass the flags argument. And this patch adds the gpio
header file to fix the build breakage when build testing with random
configuration files.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Some palmas based chip variants do not have OTG based ID logic.
For these variants we rely on GPIO based USB ID detection.
These chips do have VBUS comparator for VBUS detection so we
continue to use the old way of detecting VBUS.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch removes the mutually_exclusive array of extcon-palmas.c.
After used the unique id of each external connector on 2a9de9c0f0
("extcon: Use the unique id for external connector instead of string"),
extcon driver can't directly handle the bit value indicating the external
connectors.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch fixes NULL pointer error by removing the unneeded kfree() call
of edev->name because extcon-palmas no longer allocate the memory for edev->name.
Fixes: d71aadda19 ("extcon: Remove the optional name of extcon device")
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch just redefine the unique id of supported external connectors without
'enum extcon' type. Because unique id would be used on devictree file(*.dts) to
indicate the specific external connectors like key number of input framework.
So, I have the plan to move this definitions to following header file which
includes the unique id of supported external connectors.
- include/dt-bindings/extcon/extcon.h
Fixes: 2a9de9c0f0 ("extcon: Use the unique id for external connector instead of string")
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch uses the unique id to identify the type of external connector instead
of string name. The string name have the many potential issues. So, this patch
defines the 'extcon' enumeration which includes all supported external connector
on EXTCON subsystem. If new external connector is necessary, the unique id of
new connector have to be added in 'extcon' enumeration. There are current
supported external connector in 'enum extcon' as following:
enum extcon {
EXTCON_NONE = 0x0,
/* USB external connector */
EXTCON_USB = 0x1,
EXTCON_USB_HOST = 0x2,
/* Charger external connector */
EXTCON_TA = 0x10,
EXTCON_FAST_CHARGER = 0x11,
EXTCON_SLOW_CHARGER = 0x12,
EXTCON_CHARGE_DOWNSTREAM = 0x13,
/* Audio and video external connector */
EXTCON_LINE_IN = 0x20,
EXTCON_LINE_OUT = 0x21,
EXTCON_MICROPHONE = 0x22,
EXTCON_HEADPHONE = 0x23,
EXTCON_HDMI = 0x30,
EXTCON_MHL = 0x31,
EXTCON_DVI = 0x32,
EXTCON_VGA = 0x33,
EXTCON_SPDIF_IN = 0x34,
EXTCON_SPDIF_OUT = 0x35,
EXTCON_VIDEO_IN = 0x36,
EXTCON_VIDEO_OUT = 0x37,
/* Miscellaneous external connector */
EXTCON_DOCK = 0x50,
EXTCON_JIG = 0x51,
EXTCON_MECHANICAL = 0x52,
EXTCON_END,
};
For example in extcon-arizona.c:
To use unique id removes the potential issue about handling
the inconsistent name of external connector with string.
- Previously, use the string to register the type of arizona jack connector
static const char *arizona_cable[] = {
"Mechanical",
"Microphone",
"Headphone",
"Line-out",
};
- Newly, use the unique id to register the type of arizona jack connector
static const enum extcon arizona_cable[] = {
EXTCON_MECHANICAL,
EXTCON_MICROPHONE,
EXTCON_HEADPHONE,
EXTCON_LINE_OUT,
EXTCON_NONE,
};
And this patch modify the prototype of extcon_{get|set}_cable_state_() which
uses the 'enum extcon id' instead of 'cable_index'. Because although one more
extcon drivers support USB cable, each extcon driver might has the differnt
'cable_index' for USB cable. All extcon drivers can use the unique id number
for same external connector with modified extcon_{get|set}_cable_state_().
- Previously, use 'cable_index' on these functions:
extcon_get_cable_state_(struct extcon_dev*, int cable_index)
extcon_set_cable_state_(struct extcon_dev*, int cable_index, bool state)
-Newly, use 'enum extcon id' on these functions:
extcon_get_cable_state_(struct extcon_dev*, enum extcon id)
extcon_set_cable_state_(struct extcon_dev*, enum extcon id, bool state)
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[arnd: Report the build break about drivers/usb/phy/phy-tahvo.c after using the
unique id for external connector insteadf of string]
Reported-by: Arnd Bergmann <arnd@arndb.de>
[dan.carpenter: Report the build warning of extcon_{set|get}_cable_state_()]
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
This patch removes the optional name of extcon device. Instead,
extcon_dev_register() set the device name as 'extcon[number]' naming pattern.
- /sys/class/extcon/[hardcoded device name] -> /sys/class/extcon/extcon[number]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: Graeme Gregory <gg@slimlogic.co.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Jaewon Kim <jaewon02.kim@samsung.com>
This patch set the parent device of extcon device using first parameter of
devm_extco_dev_allocate() to remove duplicate code on all of extcon provider
drivers.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reported-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Graeme Gregory <gg@slimlogic.co.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Array of struct of_device_id may be be const as expected by
of_match_table field.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch use devm_extcon_dev_allocate() to simplify the memory control
of extcon device.
Cc: Graeme Gregory <gg@slimlogic.co.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Use the resource-managed extcon device register function (i.e.
devm_extcon_dev_register()) instead of extcon_dev_register(). If extcon device
is attached with this function, that extcon device is automatically unregistered
on driver detach. That reduces tiresome managing code.
Signed-off-by: Sangjung Woo <sangjung.woo@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
commit ca488 (extcon: of: Remove unnecessary function call by using the
name of device_node) started using node name instead of device name
to get the extcon device. This breaks dwc3-omap since it's not able to
get the extcon device anymore. Fixed it by setting edev name of
palmas to be the same as its node name.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reported-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Use SIMPLE_DEV_PM_OPS macro in order to make the code simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Always cross check with the ID state and the source of interrupt.
Also add a case in which ID Source is ID_GND but LATCH state is set
wrongly. This uses the previous Link stat to determine the new state.
Signed-off-by: George Cherian <george.cherian@ti.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The Palmas device contains only a USB VBUS-ID detector, so added a
compatible type *ti,palmas-usb-vid*. Didn't remove the existing compatible
types for backward compatibility.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch remove extcon_dev_register()'s second parameter which means
the pointer of parent device to simplify prototype of this function.
So, if extcon device has the parent device, it should set the pointer of
parent device to edev.dev.parent in extcon device driver instead of in
extcon_dev_register().
Cc: Graeme Gregory <gg@slimlogic.co.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Based on system design, platform needs to detect the VBUS or ID or
both. Provide option to select this through platform data to
disable part of cable detection through palmas-usb.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Add suspend/resume callbacks and support for wakeup from
suspend on USB HOST or USB Device cable insertion or removal.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
When integrating driver with Tegra platform, it is found that
the ID pins get detected only once after booting system and
further removal and re-insert does not detect the ID pin.
Fixing this issue with enabling interrupt on ID_GND and ID_FLOAT
always and clearing the status on LATCH register which actually
occurred.
Also if interrupt occurs with line status as zero then based on
previous status, set the cable state.
Add debug prints to display the cable state when any cable
insertion/removal happen.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
of_extcon_get_extcon_dev() uses dev_name for getting the reference
to the extcon device. If the extcon driver assigns a different
name other than dev_name, of_extcon_get_extcon_dev() wouldn't
be able to find the reference to the extcon device. Since the
client drivers of extcon-palmas would be using
of_extcon_get_extcon_dev(), removed assigning edev.name
in extcon-palmas.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
This is the driver for the USB comparator built into the palmas chip. It
handles the various USB OTG events that can be generated by cable
insertion/removal.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: George Cherian <george.cherian@ti.com>
[kishon@ti.com: adapted palmas usb driver to use the extcon framework]
Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roger Quadros