When added by ACPI, the information does not contain the slave address
of the BMC. However, that information is available from SMBIOS. So
if we add a device that doesn't have a slave address, look at the other
devices that are duplicate interfaces and see if they have a slave
address.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Some logs are printed out early using smi->dev, but on a platform device
that is not created until later. So move the creation of that device
structure earlier in the sequence so it can be used for printing.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Commit d9b7e4f717 ("ipmi: Periodically check to see if irqs and
messages are set right") to verify the contents of global events.
However, the wrong function was being called in some cases, checking
for messages, not events.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Jason DiPietro <J.DiPietro@F5.com>
Parameter trydefaults=1 causes the ipmi_init to initialize ipmi through
the legacy port io space that was designated for ipmi. Architectures
that do not map legacy port io can panic when trydefaults=1.
Rather than implement build-time conditional exceptions for each
architecture that does not map legacy port io, we have removed legacy
port io from the driver.
Parameter 'trydefaults' has been removed. Attempts to use it hereafter
will evoke the "Unknown symbol in module, or unknown parameter" message.
The patch was built against a number of architectures and tested for
regressions and functionality on x86_64 and ARM64.
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Removed the config entry and the address source entry for default,
since neither were used any more.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Commit d61a3ead26 ("[PATCH] IPMI: reserve I/O ports separately")
changed the way I/O ports were reserved and includes this comment in
log:
Some BIOSes reserve disjoint I/O regions in their ACPI tables for the IPMI
controller. This causes problems when trying to register the entire I/O
region. Therefore we must register each I/O port separately.
There is a similar problem with memio regions on an arm64 platform
(AMD Seattle). Where I see:
ipmi message handler version 39.2
ipmi_si AMDI0300:00: probing via device tree
ipmi_si AMDI0300:00: ipmi_si: probing via ACPI
ipmi_si AMDI0300:00: [mem 0xe0010000] regsize 1 spacing 4 irq 23
ipmi_si: Adding ACPI-specified kcs state machine
IPMI System Interface driver.
ipmi_si: Trying ACPI-specified kcs state machine at mem \
address 0xe0010000, slave address 0x0, irq 23
ipmi_si: Could not set up I/O space
The problem is that the ACPI core registers disjoint regions for the
platform device:
e0010000-e0010000 : AMDI0300:00
e0010004-e0010004 : AMDI0300:00
and the ipmi_si driver tries to register one region e0010000-e0010004.
Based on a patch from Mark Salter <msalter@redhat.com>, who also wrote
all the above text.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Mark Salter <msalter@redhat.com>
Extend the tryacpi module parameter to turn off acpi_ipmi_probe such
that hard-coded options (type, ports, address, etc.) have complete
control over the smi_info data structures setup by the driver.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Under some circumstances, the IPMI state machine could return
a call without delay option but the driver would still do a long
delay because the result wasn't checked. Instead of calling
the state machine after transaction done, just go back to the
top of the processing to start over.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Enclosing '#include <linux/acpi.h>' within '#ifdef CONFIG_ACPI' is
unnecessary, since it has its own conditional compile for CONFIG_ACPI.
Commit 0fbcf4af7c ("ipmi: Convert the IPMI SI ACPI handling to a
platform device") exposed this as a problem for platforms that do not
support ACPI when it introduced a call to ACPI_PTR() macro outside of
the CONFIG_ACPI conditional compile. This would have been perfectly
acceptable if acpi.h were not conditionally excluded for the non-acpi
platform, because the conditional compile within acpi.h defines
ACPI_PTR() to return NULL when compiled for non acpi platforms.
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Fixed commit reference in header to conform to standard.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
We call cleanup_one_si from ipmi_pci_remove, which calls ->addr_source_cleanup,
which gets set to point to ipmi_pci_cleanup, which does a pci_disable_device.
On return from this, we do a second pci_disable_device, which
results in the trace below.
ipmi_si 0000:00:16.0: disabling already-disabled device
Call Trace:
[<ffffffff818ce54c>] dump_stack+0x45/0x57
[<ffffffff810525f7>] warn_slowpath_common+0x97/0xe0
[<ffffffff810526f6>] warn_slowpath_fmt+0x46/0x50
[<ffffffff81497ca1>] pci_disable_device+0xb1/0xc0
[<ffffffffa00851a5>] ipmi_pci_remove+0x25/0x30 [ipmi_si]
[<ffffffff8149a696>] pci_device_remove+0x46/0xc0
[<ffffffff8156801f>] __device_release_driver+0x7f/0xf0
[<ffffffff81568978>] driver_detach+0xb8/0xc0
[<ffffffff81567e50>] bus_remove_driver+0x50/0xa0
[<ffffffff8156914e>] driver_unregister+0x2e/0x60
[<ffffffff8149a3e5>] pci_unregister_driver+0x25/0x90
[<ffffffffa0085804>] cleanup_ipmi_si+0xd4/0xf0 [ipmi_si]
[<ffffffff810c727a>] SyS_delete_module+0x12a/0x200
[<ffffffff818d4d72>] system_call_fastpath+0x12/0x17
Signed-off-by: Dave Jones <dsj@fb.com>
Lots of char arrays could be set as const since they contain only literal
char arrays.
We could in the same time make const some struct members who are pointer
to those const char arrays.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
We encountered a panic on boot in ipmi_si on a dell per320 due to an
uninitialized timer as follows.
static int smi_start_processing(void *send_info,
ipmi_smi_t intf)
{
/* Try to claim any interrupts. */
if (new_smi->irq_setup)
new_smi->irq_setup(new_smi);
--> IRQ arrives here and irq handler tries to modify uninitialized timer
which triggers BUG_ON(!timer->function) in __mod_timer().
Call Trace:
<IRQ>
[<ffffffffa0532617>] start_new_msg+0x47/0x80 [ipmi_si]
[<ffffffffa053269e>] start_check_enables+0x4e/0x60 [ipmi_si]
[<ffffffffa0532bd8>] smi_event_handler+0x1e8/0x640 [ipmi_si]
[<ffffffff810f5584>] ? __rcu_process_callbacks+0x54/0x350
[<ffffffffa053327c>] si_irq_handler+0x3c/0x60 [ipmi_si]
[<ffffffff810efaf0>] handle_IRQ_event+0x60/0x170
[<ffffffff810f245e>] handle_edge_irq+0xde/0x180
[<ffffffff8100fc59>] handle_irq+0x49/0xa0
[<ffffffff8154643c>] do_IRQ+0x6c/0xf0
[<ffffffff8100ba53>] ret_from_intr+0x0/0x11
/* Set up the timer that drives the interface. */
setup_timer(&new_smi->si_timer, smi_timeout, (long)new_smi);
The following patch fixes the problem.
To: Openipmi-developer@lists.sourceforge.net
To: Corey Minyard <minyard@acm.org>
CC: linux-kernel@vger.kernel.org
Signed-off-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: stable@vger.kernel.org # Applies cleanly to 3.10-, needs small rework before
The policy for drivers is to have MODULE_DEVICE_TABLE() just after the
struct used in it. For clarity.
Suggested-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The IPMI driver would let the final timeout just happen, but it could
easily just stop the timer. If the timer stop fails that's ok, that
should be rare.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The timer and thread were not being started for internal messages,
so in interrupt mode if something hung the timer would never go
off and clean things up. Factor out the internal message sending
and start the timer for those messages, too.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Gouji, Masayuki <gouji.masayuki@jp.fujitsu.com>
Cc: stable@vger.kernel.org
Fix autoloading ipmi modules when using device tree.
Signed-off-by: Brijesh Singh <brijeshkumar.singh@amd.com>
Moved this change up into the CONFIG_OF section to account
for changes to the probing code.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
It appears that some BMCs support interrupts but don't support setting
the irq enable bits. The interrupts are just always on. Sigh.
Add code to compensate.
The new code was very similar to another functions, so this also
factors out the common code into other functions.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Henrik Korkuc <henrik@kirneh.eu>
When flushing queued messages in run-to-completion mode,
smi_event_handler() is recursively called.
flush_messages()
smi_event_handler()
handle_transaction_done()
deliver_recv_msg()
ipmi_smi_msg_received()
smi_recv_tasklet()
sender()
flush_messages()
smi_event_handler()
...
The depth of the recursive call depends on the number of queued
messages, so it can cause a stack overflow if many messages have
been queued.
To solve this problem, this patch removes flush_messages()
from sender()@ipmi_si_intf.c. Instead, add flush_messages() to
caller side of sender() if needed. Additionally, to implement this,
add new handler flush_messages to struct ipmi_smi_handlers.
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Fixed up a comment and some spacing issues.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Factor out message flushing procedure which is used in run-to-completion
mode. This patch doesn't change the logic.
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The cleanup_one_si() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The IPMI SI driver was using direct PNP, but that was not really
ideal because the IPMI device is a platform device. There was
some special handling in the acpi_pnp.c code for making this work,
but that was breaking ACPI handling for the IPMI SSIF driver.
So without this patch there were significant issues getting the
SSIF driver to work with ACPI.
So use a platform device for ACPI detection and remove the
entry from acpi_pnp.c.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
start_next_msg() issues a message placed in smi_info->waiting_msg
if it is non-NULL. However, sender() sets a message to
smi_info->curr_msg and NULL to smi_info->waiting_msg in the context
of run_to_completion mode. As the result, it leads an infinite
loop by waiting the completion of unissued message when leaving
dying message after kernel panic.
sender() should set the message to smi_info->waiting_msg not
curr_msg.
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
When probing an ACPI table, report a specific error, instead of just
returning an error, if _IFT doesn't exist.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
commit d6c5dc18d8 ("ipmi: Remove uses of return value of seq_printf")
incorrectly changed the return value of various proc_show functions
to use seq_has_overflowed().
These functions should return 0 on completion rather than 1/true
on overflow. 1 is the same as #define SEQ_SKIP which would cause
the output to not be emitted (skipped) instead.
This is a logical defect only as the length of these outputs are
all smaller than the initial allocation done by the seq filesystem.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Here's the big char/misc driver patchset for 4.1-rc1.
Lots of different driver subsystem updates here, nothing major, full
details are in the shortlog below.
All of this has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlU2IMEACgkQMUfUDdst+yloDQCfbyIRL23WVAn9ckQse/y8gbjB
OT4AoKTJbwndDP9Kb/lrj2tjd9QjNVrC
=xhen
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big char/misc driver patchset for 4.1-rc1.
Lots of different driver subsystem updates here, nothing major, full
details are in the shortlog.
All of this has been in linux-next for a while"
* tag 'char-misc-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (133 commits)
mei: trace: remove unused TRACE_SYSTEM_STRING
DTS: ARM: OMAP3-N900: Add lis3lv02d support
Documentation: DT: lis302: update wakeup binding
lis3lv02d: DT: add wakeup unit 2 and wakeup threshold
lis3lv02d: DT: use s32 to support negative values
Drivers: hv: hv_balloon: correctly handle num_pages>INT_MAX case
Drivers: hv: hv_balloon: correctly handle val.freeram<num_pages case
mei: replace check for connection instead of transitioning
mei: use mei_cl_is_connected consistently
mei: fix mei_poll operation
hv_vmbus: Add gradually increased delay for retries in vmbus_post_msg()
Drivers: hv: hv_balloon: survive ballooning request with num_pages=0
Drivers: hv: hv_balloon: eliminate jumps in piecewiese linear floor function
Drivers: hv: hv_balloon: do not online pages in offline blocks
hv: remove the per-channel workqueue
hv: don't schedule new works in vmbus_onoffer()/vmbus_onoffer_rescind()
hv: run non-blocking message handlers in the dispatch tasklet
coresight: moving to new "hwtracing" directory
coresight-tmc: Adding a status interface to sysfs
coresight: remove the unnecessary configuration coresight-default-sink
...
Some BMCs don't let you clear the receive irq bit in the global
enables. This is kind of silly, but they give an error if you
try to clear it. Compensate for this by detecting the situation
and working around it.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Thomas D <whissi@whissi.de>
Reviewed-by: Thomas D <whissi@whissi.de>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From a locking point of view it is safe to check waiting_msg without
a lock, but there is a memory ordering issue that causes it to
possibly not be set right when viewed from another processor. We are
already claiming a lock right after that, move the check to inside
the lock to enforce the memory ordering.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The seq_printf like functions will soon be changed to return void.
Convert these uses to check seq_has_overflowed instead.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
As part of the internal y2038 cleanup, this patch removes
timespec usage in the ipmi driver, replacing it timespec64
Cc: openipmi-developer@lists.sourceforge.net
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Corey Minyard <minyard@mvista.com>
The driver uses #ifdef DEBUG_TIMING in order to conditionally print out
timestamped debug messages. Unfortunately it adds the ifdefs all over the
usage sites.
This patch cleans it up by adding a debug_timestamp() function which
is compiled out if DEBUG_TIMING isn't present. This cleans up all
the ugly ifdefs in the function logic.
Cc: openipmi-developer@lists.sourceforge.net
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Corey Minyard <minyard@mvista.com>
Removes a no longer needed FIXME comment in the function,acpi_gpe_irq_setup
for the file,ipmi_si_intf.c. This comment is no longer needed as clearly we
are passing the correct level of ACPI_GPE_LEVEL_TRIGGERED to the installer
function,acpi_install_gpe_handler due to no breakage after years of using
this ACPI level in the function,acpi_install_gpe_handler.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
On a reset, the BMC may reset the BT enable in the processor
registers (different than the global enables in the BMC). Check
it periodically and fix it if necessary.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Tony Rex <tony.rex@ericsson.com>
Tested-by: Magnus Johansson E <magnus.e.johansson@ericsson.com>
If an attention came in while handling a message response, it
could cause the state machine to go into the wrong mode and lock
things up if the state machine wasn't in normal mode. So if the
state machine is not in normal mode, save the attention flag for
later.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Tony Rex <tony.rex@ericsson.com>
Tested-by: Magnus Johansson E <magnus.e.johansson@ericsson.com>
Cc: Per Fogelström <per.fogelstrom@ericsson.com>
The BMC can be reset while we are running; that means the interrupt
and event message buffer settings may be wrong. So periodically
check to see if these values are correct, and fix them if they
are wrong.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Tony Rex <tony.rex@ericsson.com>
Tested-by: Magnus Johansson E <magnus.e.johansson@ericsson.com>
A message queue was added to the message handler, so the SMI
interfaces only need to handle one message at a time. Pull out
the message queue. This also leads to some significant
simplification in the shutdown of an interface, since the
message handler now does a lot of the cleanup.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The handling of BMC flags wasn't quite right in a few places, mainly
around enabling and disabling interrupts in the BMC. Clean up the
code and fix the handling of the flags.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
This patch fixes a bug on hotmod removing.
After ipmi interface is removed using hotmod, kernel panic occurs when
rmmod impi_si. For example, try this:
# echo "remove,"`cat /proc/ipmi/0/params` > \
/sys/module/ipmi_si/parameters/hotmod
# rmmod ipmi_si
Then, rmmod fails with the following messages.
------------[ cut here ]------------
WARNING: CPU: 12 PID: 10819 at /mnt/repos/linux/lib/list_debug.c:53 __list_del_entry+0x63/0xd0()
CPU: 12 PID: 10819 Comm: rmmod Not tainted 3.17.0-rc1 #19
Hardware name: FUJITSU-SV PRIMERGY BX920 S2/D3030, BIOS 080015 Rev.3D81.3030 02/10/2012
Call Trace:
dump_stack+0x45/0x56
warn_slowpath_common+0x7d/0xa0
warn_slowpath_fmt+0x4c/0x50
__list_del_entry+0x63/0xd0
list_del+0xd/0x30
cleanup_one_si+0x2a/0x230 [ipmi_si]
ipmi_pnp_remove+0x15/0x20 [ipmi_si]
pnp_device_remove+0x24/0x40
__device_release_driver+0x7f/0xf0
driver_detach+0xb0/0xc0
bus_remove_driver+0x55/0xd0
driver_unregister+0x2c/0x50
pnp_unregister_driver+0x12/0x20
cleanup_ipmi_si+0xbc/0xf0 [ipmi_si]
SyS_delete_module+0x132/0x1c0
system_call_fastpath+0x16/0x1b
---[ end trace 70b4377268f85c23 ]---
list_del in cleanup_one_si() fails because the smi_info is already
removed when hotmod removing.
When ipmi interface is removed by hotmod, smi_info is removed by
cleanup_one_si(), but is is still set in drvdata. Therefore when rmmod
ipmi_si, ipmi_pnp_remove tries to remove it again and fails.
By this patch, a pointer to smi_info in drvdata is cleared when hotmod
removing so that it will be not accessed when rmmod.
changelog:
v2:
- Clear drvdata in cleanup_one_si
- Change subject
v1:
https://lkml.org/lkml/2014/9/8/741
Signed-off-by: Takao Indoh <indou.takao@jp.fujitsu.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Corey Minyard