Commit 439d39a9ac ("net: phy: broadcom:
extract register definitions") added a bunch of registers to brcmphy.h
but left some to broadcom.c, move all of them to the header file since
the BCM54xx and BCM7xxx PHY drivers do share all of these registers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bare register numbers are used despite <uapi/linux/mdio.h> has MDIO_DEVS[12]
#define'd for those.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Event timestamp status messages have a variable length, ranging from
1 to 5 words (16 bit words). The current code however requires
a minimum message length of sizeof(*phy_txts). In most cases this
condition is fulfilled due to padding bytes. However, if several events
are signaled in a single message, padding bytes may not be present.
For short event timestamp status messages, the length check will fail,
and the event timestamp will be dropped.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the one hand, phy_device.c provides a generic reset function if the phy
driver does not provide a soft_reset pointer. This generic reset does not take
into account the state of the phy, with a potential failure if the phy is in
powerdown mode. On the other hand, smsc driver provides a function with both
correct reset behaviour and configuration.
This patch moves the reset part into a new smsc_phy_reset function and provides
the soft_reset pointer to have a correct reset behaviour by default.
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM7xxx internal Gigabit PHY on 28nm process do not need anything
special to be done during suspend, remove the suspend callback since it
might be harmful rather than useful. While at it, update the comment
above bcm7xxx_suspend() to reflect that it applies only to 40nm and 65nm
process PHY devices.
Fixes: b560a58c45 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@greenl8ke.davemloft.net>
The BCM7xxx internal Gigabit PHYs on 28nm process platforms come out
reset without any half-duplex or "hub" compatible advertised modes,
which was causing auto-negotiation issues coming out of S3
suspend/resume, we just could not establish a link with a half-duplex
only link partner.
Make sure that the resume function properly re-configures the PHY device
to advertise all supported modes.
Fixes: b560a58c45 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@greenl8ke.davemloft.net>
A wildcard entry with the 32-bits OUI 0x600d8400 was added as part of
the BCM7xxx internal PHY driver, but that entry might match other PHYs
that are not covered by this driver, so let's just remove it.
Fixes: b560a58c45 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@greenl8ke.davemloft.net>
Conflicts:
drivers/net/Makefile
net/ipv6/sysctl_net_ipv6.c
Two ipv6_table_template[] additions overlap, so the index
of the ipv6_table[x] assignments needed to be adjusted.
In the drivers/net/Makefile case, we've gotten rid of the
garbage whereby we had to list every single USB networking
driver in the top-level Makefile, there is just one
"USB_NETWORKING" that guards everything.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a71e3c3796 ("net: phy: Set the driver when registering an MDIO bus
device") caused the following regression on the fec driver:
root@imx6qsabresd:~# echo mem > /sys/power/state
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.003 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.002 seconds) done.
Unable to handle kernel NULL pointer dereference at virtual address 0000002c
pgd = bcd14000
[0000002c] *pgd=4d9e0831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 617 Comm: sh Not tainted 3.16.0 #17
task: bc0c4e00 ti: bceb6000 task.ti: bceb6000
PC is at fec_suspend+0x10/0x70
LR is at dpm_run_callback.isra.7+0x34/0x6c
pc : [<803f8a98>] lr : [<80361f44>] psr: 600f0013
sp : bceb7d70 ip : bceb7d88 fp : bceb7d84
r10: 8091523c r9 : 00000000 r8 : bd88f478
r7 : 803f8a88 r6 : 81165988 r5 : 00000000 r4 : 00000000
r3 : 00000000 r2 : 00000000 r1 : bd88f478 r0 : bd88f478
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5387d Table: 4cd1404a DAC: 00000015
Process sh (pid: 617, stack limit = 0xbceb6240)
Stack: (0xbceb7d70 to 0xbceb8000)
....
The problem with the original commit is explained by Russell King:
"It has the effect (as can be seen from the oops) of attaching the MDIO bus
device (itself is a bus-less device) to the platform driver, which means
that if the platform driver supports power management, it will be called
to power manage the MDIO bus device.
Moreover, drivers do not expect to be called for power management
operations for devices which they haven't probed, and certainly not for
devices which aren't part of the same bus that the driver is registered
against."
This reverts commit a71e3c3796.
Cc: <stable@vger.kernel.org> #3.16
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the use of devm_kzalloc and does away with the
kfrees in the probe and remove functions. Also, a label is removed.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current time range waiting for Rx/Tx to become ready can sometimes
be too short if a connection is not present. Increase the number of
retries and the sleep to give a bit more time. Also, change level of
the message issued from _err to _dbg if Rx/Tx do not become ready
since the underlying logic will function as if no link is established
and retry eventually.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Micrel ksz9021 PHY does not support standard IEEE standard MMD
extended register access, therefore requires stubs to fail the read
register method and do nothing for the write register method when
libphy attempts to read and/or configure Energy Efficient Ethernet
features in PHYS that do support those features. This problem
was observed on an Altera Cyclone V SOC development kit that
uses the Synopsys EMAC and the Micrel ksz9021 PHY. This patch
was tested on the same board, and Energy Efficient Ethernet is
now disabled as expected since the Micrel PHY does not support that
feature.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
libphy was originally written assuming all phy devices support clause 45
access extensions to the mmd registers through the indirection registers
located within the first 16 phy registers. This assumption is not true
in all cases, and one specific example is the Micrel ksz9021 10/100/1000
Mbps phy. Using the stmmac driver, accessing the mmd registers to query
and configure energy efficient Ethernet (EEE) features yielded unexpected
behavior.
This patch adds mmd access functions to the phy driver that can be
overriden by the phy specific driver if the phy does not support this
mechanism or uses it's own non-standard access mechanism. By default,
the IEEE Compatible clause 45 access mechanism described in clause 22
is used. With this patch, EEE query/configure functions as expected
using the stmmac and the Micrel ksz9021 phy.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a netdev_info statement detailing whether auto-negotiation was
completed through parallel detection or through the auto-negotiation
protocol.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of changing rates to KR mode, KR training is initiated. If
the KR training is restarted it is possible to enter an invalid logic
state. This can be avoided by asserting a training reset bit before
initiating the KR training and then clearing the training reset bit.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the logic will loop endlessly waiting for a rate change
to complete. Add a counter so that if the rate change signals
never indicate complete the loop will eventually exit.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the amd-xgbe driver and phylib driver to better support
the 2.5GbE mode for the hardware. In order to be able establish
2.5GbE using clause 73 auto negotiation the device will support
speed sets of 1GbE/10GbE and 2.5GbE/10GbE.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 87aa9f9c61 ("net: phy: consolidate PHY reset in phy_init_hw()")
moved the call to phy_scan_fixups() in phy_init_hw() after a software
reset is performed.
By the time phy_init_hw() is called in phy_device_register(), no driver
has been bound to this PHY yet, so all the checks in phy_init_hw()
against the PHY driver and the PHY driver's config_init function will
return 0. We will therefore never call phy_scan_fixups() as we should.
Fix this by calling phy_scan_fixups() and check for its return value to
restore the intended functionality.
This broke PHY drivers which do register an early PHY fixup callback to
intercept the PHY probing and do things like changing the 32-bits unique
PHY identifier when a pseudo-PHY address has been used, as well as
board-specific PHY fixups that need to be applied during driver probe
time.
Reported-by: Hauke Merthens <hauke-m@hauke-m.de>
Reported-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds proper module_{get,put} to prevent the MDIO bus module
from being unloaded while the phydev is connected. By doing so, we fix
a kernel panic produced when a MDIO driver is removed, but the phydev
that relies on it is attached and running.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdiobus_register() registers a device which is already bound to a driver.
Hence, the driver pointer should be set properly in order to track down
the driver associated to the MDIO bus.
This will be used to allow ethernet driver to pin down a MDIO bus driver,
preventing it from being unloaded while the PHY device is running.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When timestamping received packets, rx_timestamp_work may be scheduled
before the timestamps is received from the hardware resulting in the
packet beeing delivered without the timestamp.
This is fixed by changing the receive timestamp path:
On receiving a packet that need timestamping, the rxts list is
traversed. If a match is found, packet+timestamp are delivered,
otherwise the packet is added to a rx_queue.
When a timestamp arrives rx_queue is traversed and if a matching
packet is found, it is delivered with the timestamp. Otherwise the
timestamp is added to the rxts list for matching with packets arriving
later.
In case the hardware drops a timestamp, a workqueue regularly checks
the queue for old packets and delivers them without a timestamp.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expand the phy speed/duplex settings array to support more
than just baseT features. This change adds entries to support
the following additional speed/duplex/media types:
SUPPORTED_10000baseKR_Full
SUPPORTED_10000baseKX4_Full
SUPPORTED_2500baseX_Full
SUPPORTED_1000baseKX_Full
Additionally, it changes the 10GbE baseT entry from using the
hardcoded value 10000 to the SPEED_10000 define.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Event timestamp values should be adjusted by 3*reference clock period +
11 ns = 35 ns to compensate for input path and synchronization delays.
So subtract 35ns from event timestamps.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently status frames are only handled when packet timestamping is
enabled, but status frames are also needed for pin event timestamping.
Fix by moving packet timestamping check to after status frame decode.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_suspend and phy_resume are two commonly used helper functions that
need to be exported for Ethernet drivers to be built as modules
Fixes: 40755a0fce ("net: systemport: add suspend and resume support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This extends the ptp bpf to also match ptp over ip over vlan packets. The ptp
classes are changed to orthogonal bitfields representing version, transport
and vlan values to simplify matching.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 86f6cf4127 (net: of_mdio: add of_mdiobus_link_phydev()) introduced a
circular dependency between libphy and of_mdio.
depmod: ERROR: <modroot>/kernel/drivers/net/phy/libphy.ko in
dependency cycle!
depmod: ERROR: <modroot>/kernel/drivers/of/of_mdio.ko in dependency cycle!
The problem is that of_mdio.c references &mdio_bus_type and libphy now
references of_mdiobus_link_phydev.
Fix this by not exporting of_mdiobus_link_phydev() from of_mdio.ko.
Make it a static function in mdio_bus.c instead.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Jeff Mahoney <jeffm@suse.com>
Fixes: 86f6cf4127 (net: of_mdio: add of_mdiobus_link_phydev())
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For consistency, use the ptp_find_pin function to get the calibration pin,
not gpio_tab.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This constraints the pin assignment to not allow the calibration function to
be reassigned and only allow reassigning the calibratin pin if only one phy is
connected.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch increases the number of supported periodic output pins from
1 to 7. The last pin is reserved for sync.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Periodic output triggers 0 and 1 of the dp83640 has a programmable
duty-cycle which is controlled by the Pulsewidth2 field of the trigger
data register. This field is not documented in the datasheet, but it
is described in the "PHYTER Software Development Guide" section
3.1.4.1. Failing to set the field can result in unstable/no trigger
output.
Add programming of the Pulsewidth2 field, setting it to the same value
as the Pulsewidth field for a 50% duty cycle.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/phy/at803x.c:196:26-32: ERROR: application of sizeof to pointer
sizeof when applied to a pointer typed expression gives the size of
the pointer
Generated by: scripts/coccinelle/misc/noderef.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AT8030 will enter a FIFO error mode if a packet is transmitted while
the cable is unplugged. This hardware issue is acknowledged by the
vendor, and the only proposed solution is to conduct a hardware reset
via the external pin each time the link goes down. There is apparantly
no way to fix up the state via the register set.
This patch adds support for reading a 'reset-gpios' property from the DT
node of the PHY. If present, this gpio is used to apply a hardware reset
each time a 'link down' condition is detected. All relevant registers
are read out before, and written back after the reset cycle.
Doing this every time the link goes down might seem like overkill, but
there is unfortunately no way of figuring out whether the PHY is in
such a lock-up state. Hence, this is the only way of reliably fixing up
things.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes magic values from two tables and also allows us to match
against specific PHY models at runtime.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a notify callback to inform phy drivers when the core is about to
do its link adjustment. No change for drivers that do not implement
this callback.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using phy_drivers_register/_unregister functions is proper way to
handle multiple PHY drivers registration. For Realtek PHY drivers
module, it fixes incomplete current error-handlings up and adds
missed unregistration for the RTL8201CP driver.
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following compilation warning:
[...]
CC drivers/net/phy/amd-xgbe-phy.o
drivers/net/phy/amd-xgbe-phy.c:1353:30: warning:
‘amd_xgbe_phy_ids’ defined but not used [-Wunused-variable]
static struct mdio_device_id amd_xgbe_phy_ids[] = {
^
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides the Kconfig and Makefile changes needed
to configure and build the AMD 10GbE platform driver and the
AMD 10GbE phylib driver.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides the initial phylib driver in support
of the AMD 10GbE device.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a function to walk the list of subnodes of a mdio bus and look for
a node that matches the phy's address with its 'reg' property. If found,
set the of_node pointer for the phy. This allows auto-probed pyh
devices to be augmented by information passed in via DT.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_alb.c
drivers/net/ethernet/altera/altera_msgdma.c
drivers/net/ethernet/altera/altera_sgdma.c
net/ipv6/xfrm6_output.c
Several cases of overlapping changes.
The xfrm6_output.c has a bug fix which overlaps the renaming
of skb->local_df to skb->ignore_df.
In the Altera TSE driver cases, the register access cleanups
in net-next overlapped with bug fixes done in net.
Similarly a bug fix to send ALB packets in the bonding driver using
the right source address overlaps with cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
of_set_phy_supported allows overwiting hardware capabilities of
a phy with values from the devicetree. of_set_phy_supported is
called right after phy_device_register in the assumption that
phy_probe is called from phy_device_register and the features
of the phy are already initialized. For the genphy driver this
is not true, here phy_probe is called later during phy_connect
time. phy_probe will then overwrite all settings done from
of_set_phy_supported
Fix this by moving of_set_phy_supported to the core phy code
and calling it from phy_probe.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_set_phy_supported allows overwiting hardware capabilities of
a phy with values from the devicetree. This does not work with
the genphy driver though because the genphys config_init function
will overwrite all values adjusted by of_set_phy_supported. Fix
this by initialising the genphy features in the phy_driver struct
and in config_init just limit the features to the ones the hardware
can actually support. The resulting features are a subset of the
devicetree specified features and the hardware features.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing fixed_phy_add() function has several drawbacks that
prevents it from being used as is for OF-based declaration of fixed
PHYs:
* The address of the PHY on the fake bus needs to be passed, while a
dynamic allocation is desired.
* Since the phy_device instantiation is post-poned until the next
mdiobus scan, there is no way to associate the fixed PHY with its
OF node, which later prevents of_phy_connect() from finding this
fixed PHY from a given OF node.
To solve this, this commit introduces fixed_phy_register(), which will
allocate an available PHY address, add the PHY using fixed_phy_add()
and instantiate the phy_device structure associated with the provided
OF node.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, the fixed_phy_add() function was taking as argument
'phy_id', which was used both as the PHY address on the fake fixed
MDIO bus, and as the PHY id, as available in the MII_PHYSID1 and
MII_PHYSID2 registers. However, those two informations are completely
unrelated.
This patch decouples them. The PHY id of fixed PHYs is hardcoded to be
0x0. Ideally, a really reserved value would be nicer, but there
doesn't seem to be an easy of making sure a dummy value can be
assigned to the Linux kernel for such usage.
The PHY address remains passed by the caller of phy_fixed_add().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit be9dad1f9f ("net: phy: suspend phydev when going
to HALTED"), an unused PHY device will be put in a low-power mode
using BMCR_PDOWN. Some Ethernet drivers might be calling phy_start()
and phy_stop() from ndo_open and ndo_close() respectively, while
calling phy_connect() and phy_disconnect() from probe and remove.
In such a case, the PHY will be powered down during the phy_stop()
call, but will fail to be powered up in phy_start().
This patch fixes this scenario.
Signed-off-by: Jiancheng Xue <xuejiancheng@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the call to phy_init_hw failed in phy_attach_direct, phy_detach is called
to detach the phy device from its network device. If the attached driver is a
generic phy driver, this also detaches the driver. Subsequently phy_resume
is called, which assumes without checking that a driver is attached to the
device. This will result in a crash such as
Unable to handle kernel paging request for data at address 0xffffffffffffff90
Faulting instruction address: 0xc0000000003a0e18
Oops: Kernel access of bad area, sig: 11 [#1]
...
NIP [c0000000003a0e18] .phy_attach_direct+0x68/0x17c
LR [c0000000003a0e6c] .phy_attach_direct+0xbc/0x17c
Call Trace:
[c0000003fc0475d0] [c0000000003a0e6c] .phy_attach_direct+0xbc/0x17c (unreliable)
[c0000003fc047670] [c0000000003a0ff8] .phy_connect_direct+0x28/0x98
[c0000003fc047700] [c0000000003f0074] .of_phy_connect+0x4c/0xa4
Only call phy_resume if phy_init_hw was successful.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/altera/altera_sgdma.c
net/netlink/af_netlink.c
net/sched/cls_api.c
net/sched/sch_api.c
The netlink conflict dealt with moving to netlink_capable() and
netlink_ns_capable() in the 'net' tree vs. supporting 'tc' operations
in non-init namespaces. These were simple transformations from
netlink_capable to netlink_ns_capable.
The Altera driver conflict was simply code removal overlapping some
void pointer cast cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 6d48f44b7b "mdio_bus: implement devm_mdiobus_alloc/devm_mdiobus_free"
introduced a new function devm_mdiobus_alloc_size() but added an export
for a different function devm_mdiobus_alloc(), which was obviously
a simple mistake that leads to build error whenever this function is
used from a loadable module:
ERROR: "devm_mdiobus_alloc_size" [drivers/net/ethernet/ti/davinci_mdio.ko] undefined!
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a sane default bus id (rather than -ENODEV) and print a warning when
the bus alias id is missing.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for ksz9031 PAD skew configuration over devicetree.
Signed-off-by: Hubert Chaumette <hchaumette@adeneo-embedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a resource managed devm_mdiobus_alloc[_size]()/devm_mdiobus_free()
to automatically clean up MDIO bus alocations made by MDIO drivers,
thus leading to simplified MDIO drivers code.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-and-tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_state_machine should check whether auto-negotiatin is completed
before changing phydev->state from PHY_NOLINK to PHY_RUNNING. If
auto-negotiation is not completed phydev->state should be set to
PHY_AN.
Signed-off-by: Balakumaran Kannan <kumaran.4353@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/igb/e1000_mac.c
net/core/filter.c
Both conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This was caught when using a spatch (aka. coccinelle) script
written by Joe Perches.
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ksz9021_load_values_from_of() val2 to val4 aren't tested against their
initialization value.
This causes the test to always succeed, and this value to be used as if it
was loaded from the devicetree instead of being ignored, in case of a
missing/invalid property in the ethernet OF device node.
As a result, the value "0" is written to the relevant registers.
Change the conditions to test against the right initialization value.
Signed-off-by: Hubert Chaumette <hchaumette@adeneo-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the generic bits from genphy_config_init() instead of implementing
the same functionality again.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables other drivers to call this generic implementation, and then
only do specific details on top of it.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is for a system with fixed assignments of input and output pins
(various variants of Kontron COMe).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some systems using mdio-gpio may use active-low gpio pins
(eg with inverters or FETs connected to all or some of the
gpio pins).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simplifies error path and deinit/removal functions.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This condition check makes no difference in the code flow since 3.10
Signed-off-by: Balakumaran Kannan <kumaran.4353@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Micrel KSZ8864RMN switch to the spi_ks8995
driver. The KSZ8864RMN switch has a wider 256-byte register space.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit fixes a build error reported by Fengguang, that is
triggered when CONFIG_NETWORK_PHY_TIMESTAMPING is not set:
ERROR: "ptp_classify_raw" [drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe.ko] undefined!
The fix is to introduce its own file for the PTP BPF classifier,
so that PTP_1588_CLOCK and/or NETWORK_PHY_TIMESTAMPING can select
it independently from each other. IXP4xx driver on ARM needs to
select it as well since it does not seem to select PTP_1588_CLOCK
or similar that would pull it in automatically.
This also allows for hiding all of the internals of the BPF PTP
program inside that file, and only exporting relevant API bits
to drivers.
This patch also adds a kdoc documentation of ptp_classify_raw()
API to make it clear that it can return PTP_CLASS_* defines. Also,
the BPF program has been translated into bpf_asm code, so that it
can be more easily read and altered (extensively documented in [1]).
In the kernel tree under tools/net/ we have bpf_asm and bpf_dbg
tools, so the commented program can simply be translated via
`./bpf_asm -c prog` where prog is a file that contains the
commented code. This makes it easily readable/verifiable and when
there's a need to change something, jump offsets etc do not need
to be replaced manually which can be very error prone. Instead,
a newly translated version via bpf_asm can simply replace the old
code. I have checked opcode diffs before/after and it's the very
same filter.
[1] Documentation/networking/filter.txt
Fixes: 164d8c6665 ("net: ptp: do not reimplement PTP/BPF classifier")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jiri Benc <jbenc@redhat.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The at8031 can work on polling mode and interrupt mode.
Add ack_interrupt and config intr funcs to enable
interrupt mode for it.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sun4i_mdio_reset() does nothing useful and is optional for the MDIO bus
code, so let's just remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AFE_RX_LP_COUNTER kept the last 3 bits set, which would not properly
clear the EEE LPI mode errors bits. Make sure that those bits are set to
0 to ensure the PHY timing is always good even during EEE wake-up.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Writing first to the AFE registers, and then the VCO, RCAL, RC_CAL
registers turned out to unveil some spurious MDIO read/write failures
which would make the workaround partially applied. The fix is to write
first to the VCO, RCAL, RC_CAL registers, and then write to the AFE
registers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define constants for the various registers used in
bcm7xxx_28nm_afe_config_init() to help clarify what this workaround is
about.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
Documentation/devicetree/bindings/net/micrel-ks8851.txt
net/core/netpoll.c
The net/core/netpoll.c conflict is a bug fix in 'net' happening
to code which is completely removed in 'net-next'.
In micrel-ks8851.txt we simply have overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver use the new pin configuration method when
programming the periodic output signal.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver to use the new pin configuration method when
programming the external time stamp input signals.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adapts the dp83640 driver to allow reconfiguration of which
auxiliary function goes on which pin. The functions may be reassigned
freely with the one exception of the calibration function.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phyter driver incorrectly feeds the value of the period into what
is in fact a pulse width register, resulting in the actual period
being twice the dialed value. This patch fixes the issue and renames a
variable to make the code at bit more clear.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up the input checking code on the external time stamp
function by using an unsigned rather than a signed channel index.
Also, this patch corrects the author's email address. When this macro
was last changed, the top level domain part of the email address was
left behind.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 20d8435a1c (phy: micrel: add of configuration for LED mode) made the
obvious mistake when masking off the LED mode bits: forgot to do a logical NOT
to the mask with which it ANDs the register value, so that unrelated bits are
cleared instead.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Callers of phy_ethtool_get_wol are supposed to provide a properly
cleared struct ethtool_wolinfo. Therefore, fix phy_suspend to clear
it before passing it to phy_ethtool_get_wol.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/r8152.c
drivers/net/xen-netback/netback.c
Both the r8152 and netback conflicts were simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
With -Werror=array-bounds, gcc v4.7.x warns that in phy_find_valid(), the
settings[] "array subscript is above array bounds", I think because idx is
a signed integer and if the caller supplied idx < 0, we pass the guard but
still reference out of bounds.
Fix this by making idx unsigned here and elsewhere.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
net/ipv6/sit.c
The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.
The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the led-mode property for the following PHYs
which have a single LED mode configuration value.
KSZ8001 and KSZ8041 which both use register 0x1e bits 15,14 and
KSZ8021, KSZ8031 and KSZ8051 which use register 0x1f bits 5,4
to control the LED configuration.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Masking the link partner's capabilities with local capabilities can be
misleading in autonegotiation scenarios such as PAUSE frame
autonegotiation.
This patch calculates the join between the local capabilities and the
link parner capabilities, when it determines the speed and duplex
settings, but does not mask any of the link partner capabilities when
it calculates PAUSE frame settings.
Signed-off-by: Cristian Bercaru <cristian.bercaru@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_3ad.h
drivers/net/bonding/bond_main.c
Two minor conflicts in bonding, both of which were overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed out by Shaohui, most 10G PHYs out there have a non-standard
compliant software reset sequence, eventually something much more
complex than just toggling the BMCR_RESET bit. Allow PHY driver to
implement their own soft_reset() callback to deal with that. If no
callback is provided, call into genphy_soft_reset() which makes sure the
existing behavior is kept intact.
Reported-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed out by Shaohui, this function is generic for 10/100/1000
PHYs, but 10G PHYs might have a slightly different reset sequence which
prevents most of them from using this function.
Move the BMCR_RESET based software resent sequence to
genphy_soft_reset() in preparation for allowing PHY drivers to implement
a soft_reset() callback.
Reported-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Broadcom BCM7xxx Set Top Box SoCs
internal PHYs. This driver supports the following generation of SoCs:
- BCM7366, BCM7439, BCM7445 (28nm process)
- all 40nm and 65nm (older MIPS-based SoCs)
The PHYs on these SoCs require a bunch of workarounds to operate
correctly, both during configuration time and at suspend/resume time,
the driver handles that for us.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Broadcom BCM54xx register definitions are shared between BCM54xx and
BCM7xx internal PHYs for which we are adding support. Extract these
register definitions and put them in include/linux/brcmphy.h for use by
the BCM7xxx internal PHY driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MoCA PHYs are using coaxial (BNC-like) connectors, update the
transceiver port type when replying to ethtool.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_init_hw not does a full PHY reset after the driver probe has
finished, so any hw initialization done in the probe will be lost.
Part of the timestamping functionality of the dp83640 is set up in the
probe and with that lost, enabling timestamping will cause a PHY
lockup, requiring a hard reset / power cycle to recover.
This patch moves all the HW initialization in dp83640_probe to
dp83640_config_init.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose the PHY device has_fixups boolean as a sysfs property to help
troubleshooting PHY configurations.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a boolean property which indicates if the PHY has had any fixup
routine ran on it. We are later going to use that boolean to expose it
as a sysfs property to help troubleshooting.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose the PHY device interface mode through sysfs since this is an
useful piece of information for knowing how the attached networking
device will have configured its transmit/receive path.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comments above phy_{clear,config}_interrupt used the word "on"
instead of "or", when talking about the return values of the functions,
fix these two typos.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHYs out there can be very quirky with respect to how they would
report the auto-negotiation is completed. Allow drivers to override the
generic aneg_done() implementation by providing their own.
Since not all drivers have been updated yet to use genphy_aneg_done() as
aneg_done() callback, we explicitely check that this callback is valid
before calling into it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for allowing PHY drivers to potentially override their
auto-negotiation done callback, move the contents of phy_aneg_done() to
genphy_aneg_done() since that function really is the generic
implementation based on the BMSR_ANEGCOMPLETE status.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a convenience function: phy_speed_to_str() which will display human
readable speeds.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update phy_print_status() to also display the PHY device pause settings
(rx/tx or off).
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_print_status() currently uses dev_name(&phydev->dev) which will
usually result in printing something along those lines for Device Tree
aware drivers:
libphy: f0b60000.etherne:0a - Link is Down
libphy: f0ba0000.etherne:00 - Link is Up - 1000/Full
This is not terribly useful for network administrators or users since we
expect a network interface name to be able to correlate link events with
interfaces. Update phy_print_status() to use netdev_info() with
phydev->attached_dev which is the backing network device for our PHY
device. The leading dash is removed since netdev_info() prefixes the
messages with "<interface>: " already.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Fix flexcan build on big endian, from Arnd Bergmann
2) Correctly attach cpsw to GPIO bitbang MDIO drive, from Stefan Roese
3) udp_add_offload has to use GFP_ATOMIC since it can be invoked from
non-sleepable contexts. From Or Gerlitz
4) vxlan_gro_receive() does not iterate over all possible flows
properly, fix also from Or Gerlitz
5) CAN core doesn't use a proper SKB destructor when it hooks up
sockets to SKBs. Fix from Oliver Hartkopp
6) ip_tunnel_xmit() can use an uninitialized route pointer, fix from
Eric Dumazet
7) Fix address family assignment in IPVS, from Michal Kubecek
8) Fix ath9k build on ARM, from Sujith Manoharan
9) Make sure fail_over_mac only applies for the correct bonding modes,
from Ding Tianhong
10) The udp offload code doesn't use RCU correctly, from Shlomo Pongratz
11) Handle gigabit features properly in generic PHY code, from Florian
Fainelli
12) Don't blindly invoke link operations in
rtnl_link_get_slave_info_data_size, they are optional. Fix from
Fernando Luis Vazquez Cao
13) Add USB IDs for Netgear Aircard 340U, from Bjørn Mork
14) Handle netlink packet padding properly in openvswitch, from Thomas
Graf
15) Fix oops when deleting chains in nf_tables, from Patrick McHardy
16) Fix RX stalls in xen-netback driver, from Zoltan Kiss
17) Fix deadlock in mac80211 stack, from Emmanuel Grumbach
18) inet_nlmsg_size() forgets to consider ifa_cacheinfo, fix from Geert
Uytterhoeven
19) tg3_change_mtu() can deadlock, fix from Nithin Sujir
20) Fix regression in setting SCTP local source addresses on accepted
sockets, caused by some generic ipv6 socket changes. Fix from
Matija Glavinic Pecotic
21) IPPROTO_* must be pure defines, otherwise module aliases don't get
constructed properly. Fix from Jan Moskyto
22) IPV6 netconsole setup doesn't work properly unless an explicit
source address is specified, fix from Sabrina Dubroca
23) Use __GFP_NORETRY for high order skb page allocations in
sock_alloc_send_pskb and skb_page_frag_refill. From Eric Dumazet
24) Fix a regression added in netconsole over bridging, from Cong Wang
25) TCP uses an artificial offset of 1ms for SRTT, but this doesn't jive
well with TCP pacing which needs the SRTT to be accurate. Fix from
Eric Dumazet
26) Several cases of missing header file includes from Rashika Kheria
27) Add ZTE MF667 device ID to qmi_wwan driver, from Raymond Wanyoike
28) TCP Small Queues doesn't handle nonagle properly in some corner
cases, fix from Eric Dumazet
29) Remove extraneous read_unlock in bond_enslave, whoops. From Ding
Tianhong
30) Fix 9p trans_virtio handling of vmalloc buffers, from Richard Yao
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (136 commits)
6lowpan: fix lockdep splats
alx: add missing stats_lock spinlock init
9p/trans_virtio.c: Fix broken zero-copy on vmalloc() buffers
bonding: remove unwanted bond lock for enslave processing
USB2NET : SR9800 : One chip USB2.0 USB2NET SR9800 Device Driver Support
tcp: tsq: fix nonagle handling
bridge: Prevent possible race condition in br_fdb_change_mac_address
bridge: Properly check if local fdb entry can be deleted when deleting vlan
bridge: Properly check if local fdb entry can be deleted in br_fdb_delete_by_port
bridge: Properly check if local fdb entry can be deleted in br_fdb_change_mac_address
bridge: Fix the way to check if a local fdb entry can be deleted
bridge: Change local fdb entries whenever mac address of bridge device changes
bridge: Fix the way to find old local fdb entries in br_fdb_change_mac_address
bridge: Fix the way to insert new local fdb entries in br_fdb_changeaddr
bridge: Fix the way to find old local fdb entries in br_fdb_changeaddr
tcp: correct code comment stating 3 min timeout for FIN_WAIT2, we only do 1 min
net: vxge: Remove unused device pointer
net: qmi_wwan: add ZTE MF667
3c59x: Remove unused pointer in vortex_eisa_cleanup()
net: fix 'ip rule' iif/oif device rename
...
The Allwinner A10 compatibles were following a slightly different compatible
patterns than the rest of the SoCs for historical reasons. Add compatibles
matching the other pattern to the mdio driver for consistency, and keep the
older one for backward compatibility.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a Gigabit PHY device is connected to a 10/100Mbits capable Ethernet
MAC, the driver will restrict the phydev->supported modes to mask off
Gigabit. If the Gigabit PHY comes out of reset with the Gigabit features
set by default in MII_CTRL1000, it will keep advertising these feature,
so by the time we call genphy_config_advert(), the condition on
phydev->supported having the Gigabit features on is false, and we do not
update MII_CTRL1000 with updated values, and we keep advertising Gigabit
features, eventually configuring the PHY for Gigabit whilst the Ethernet
MAC does not support that.
This patches fixes the problem by ensuring that the Gigabit feature bits
are always cleared in MII_CTRL1000, if the PHY happens to be a Gigabit
PHY, and then, if Gigabit features are supported, setting those and
updating MII_CTRL1000 accordingly.
Reported-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The trigger and events functionality can be useful even if packet
timestamping is not used, but the required PTP clock is only enabled
when packet timestamping is started. This patch moves the clock enable
to when the interface is configured.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the external timestamping code is hardcoded to use the
rising edge even though the hardware has configurable event edge
detection. This patch changes the code to use falling edge detection
if PTP_FALLING_EDGE is set in the user supplied flags.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the SKBTX_IN_PROGRESS bit in tx_flags dp83640_txtstamp when doing
tx timestamps as per Documentation/networking/timestamping.txt.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is required to call put_device() if device_register() fails, so that
we give up the last reference to the device. Calling put_device allows
for mdiobus_release to be executed, kfreeing the bus.
Signed-off-by: Levente Kurusa <levex@linux.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: David Daney <david.daney@cavium.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Code should avoid needless exports, don't export something unless it used.
Make local functions static and remove unused stubs.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_attach_direct() may now attach to a generic 10G driver. It can
also be used exactly as phy_connect_direct(), which will be useful
when using of_mdio, as phy_connect (and therefore of_phy_connect)
start the PHY state machine, which is currently irrelevant for 10G
PHYs.
Signed-off-by: Andy Fleming <afleming@gmail.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Very incomplete, but will allow for binding an ethernet controller
to it.
Signed-off-by: Andy Fleming <afleming@gmail.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Then other generic phy driver such as generic 10g phy driver can join it.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_scan_fixups() isn't and shouldn't be called by the drivers directly, so
unexport it. And since Florian Fainelli's recent patches, the function is only
called locally, so we can make it static as well.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove adjust_state() callback from 'struct phy_device' since it seems to have
never been really used from the inception: phy_start_machine() has been always
called with 2nd argument equal to NULL.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove excess empty lines such as those between a function call and its result
check and just duplicate ones between functions.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some excess code:
- convert assignments to initializers;
- kill useless assignments before *return*.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of functions (especially in phy.c) has local variables that were hardly
needed in the first place -- remove them.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent patch from Florian Fainelli fixed all 'checkpatch.pl' errors but left
some warnings like:
- including <asm/io.h> instead of <linux/io.h>;
- including <asm/uaccess.h> instead of <linux/uaccess.h>;
- block comments using empty /* line;
- 'struct dev_pm_ops' variable not being *const*.
While fixing these, also fix the following style issues (some of which were
found running 'checkpatch.pl --strict'):
- alignment not matching open paren;
- file name in the heading comment.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent patch from Florian Fainelli fixed all 'checkpatch.pl' errors but left
the numerous warnings:
- including <asm/io.h> instead of <linux/io.h>;
- including <asm/uaccess.h> instead of <linux/uaccess.h>;
- *extern* declaration in .c file;
- block comments using empty /* line;
- block comments not starting with * on the middle lines;
- block comments not having trailing */ on a separate line;
- EXPORT_SYMBOL() not immediately following its function;
- unnecessary {} for signle statement block;
- spaces before tabs.
While fixing these, also fix the following style issues (some of which were
found running 'checkpatch.pl --strict'):
- alignment not matching open paren;
- missing {} on one of the *if* arms where another has them;
- use of sizeof(struct structure) instead of sizeof(*variable);
- multiple assignments on one line;
- empty line before };
- file names in the heading comments;
- missing spaces around operators;
- no {} around multi-line *if* operator's arm;
- unneeded () around subexpressions;
- incomplete kernel-doc comment style;
- comment line exceeding 80 characters;
- missing empty line after declarations.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the way PHY IRQ handler is implemented (all real handling being pushed to
the workqueue and returning IRQ_HANDLED all the time PHY is active), we cannot
really claim that PHY IRQ can be shared when calling request_irq().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/i40e/i40e_main.c
drivers/net/macvtap.c
Both minor merge hassles, simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch spotted a few checkpatch errors such as whitespace damages
and switch/case labels not being on the same column, fix them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch spotted a few spaces vs tabs errors, fix them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpath spotted a few errors in this file, fix them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpath spotted a few stylistic errors, fix them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpath spotted a few stylistic errors fix them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When phydev is going to HALTED state, we can try to suspend it to
safe more power. phy_suspend helper will check if PHY can be suspended,
so just call it when entering HALTED state.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This ensures PHYs are resumed on attach and suspended on detach.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds helper functions to resume and suspend a given phy_device
by calling the corresponding driver callbacks if available.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell PHYs support generic PHY suspend/resume, so provide those
callbacks to all marvell specific drivers.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renesas R-Car development boards use KSZ8041RNLI PHY which for some reason has
ID of 0x00221537 that is not documented for KSZ8041-family PHYs and does not
match the documented ID of 0x0022151x (where 'x' is the revision). We have
to add the new #define PHY_ID_* and new ksphy_driver[] entry, almost the same
as KSZ8041 one, differing only in the 'phy_id' and 'name' fields.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are quite a lot of drivers touching a PHY device MII_BMCR
register to reset the PHY without taking care of:
1) ensuring that BMCR_RESET is cleared after a given timeout
2) the PHY state machine resuming to the proper state and re-applying
potentially changed settings such as auto-negotiation
Introduce phy_poll_reset() which will take care of polling the MII_BMCR
for the BMCR_RESET bit to be cleared after a given timeout or return a
timeout error code.
In order to make sure the PHY is in a correct state, phy_init_hw() first
issues a software reset through MII_BMCR and then applies any fixups.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use phy_init_hw() instead of open-coding it in phy_mii_ioctl(), this
improves consistenty and makes sure that we will not duplicate the same
routine somewhere else.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY library already reads the MII_STAT1000 and MII_LPA registers in
genphy_read_status(), so extend it to also populate the PHY device link
partner advertised features such that we can feed this back into ethtool
when asked for it in phy_ethtool_gset().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add auto-MDI/MDI-X capability for forced (autonegotiation disabled)
10/100 Mbps speeds on Vitesse VSC82x4 PHYs. Exported previously static
function genphy_setup_forced() required by the new config_aneg handler
in the Vitesse PHY module.
Signed-off-by: Madalin Bucur <madalin.bucur@freescale.com>
Signed-off-by: Shruti Kanetkar <Shruti@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vitesse VSC8662 is Dual Port 10/100/1000Base-T Phy
Its register set and features are similar to other Vitesse Phys.
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Andy Fleming <afleming@gmail.com>
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VSC8574 is a quad-port Gigabit Ethernet transceiver with four SerDes
interfaces for quad-port dual media capability.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@gmail.com>
Signed-off-by: Shruti Kanetkar <Shruti@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vitesse VSC8234 is quad port 10/100/1000BASE-T PHY
with SGMII and SERDES MAC interfaces.
Signed-off-by: Andy Fleming <afleming@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Shruti Kanetkar <Shruti@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) The addition of nftables. No longer will we need protocol aware
firewall filtering modules, it can all live in userspace.
At the core of nftables is a, for lack of a better term, virtual
machine that executes byte codes to inspect packet or metadata
(arriving interface index, etc.) and make verdict decisions.
Besides support for loading packet contents and comparing them, the
interpreter supports lookups in various datastructures as
fundamental operations. For example sets are supports, and
therefore one could create a set of whitelist IP address entries
which have ACCEPT verdicts attached to them, and use the appropriate
byte codes to do such lookups.
Since the interpreted code is composed in userspace, userspace can
do things like optimize things before giving it to the kernel.
Another major improvement is the capability of atomically updating
portions of the ruleset. In the existing netfilter implementation,
one has to update the entire rule set in order to make a change and
this is very expensive.
Userspace tools exist to create nftables rules using existing
netfilter rule sets, but both kernel implementations will need to
co-exist for quite some time as we transition from the old to the
new stuff.
Kudos to Patrick McHardy, Pablo Neira Ayuso, and others who have
worked so hard on this.
2) Daniel Borkmann and Hannes Frederic Sowa made several improvements
to our pseudo-random number generator, mostly used for things like
UDP port randomization and netfitler, amongst other things.
In particular the taus88 generater is updated to taus113, and test
cases are added.
3) Support 64-bit rates in HTB and TBF schedulers, from Eric Dumazet
and Yang Yingliang.
4) Add support for new 577xx tigon3 chips to tg3 driver, from Nithin
Sujir.
5) Fix two fatal flaws in TCP dynamic right sizing, from Eric Dumazet,
Neal Cardwell, and Yuchung Cheng.
6) Allow IP_TOS and IP_TTL to be specified in sendmsg() ancillary
control message data, much like other socket option attributes.
From Francesco Fusco.
7) Allow applications to specify a cap on the rate computed
automatically by the kernel for pacing flows, via a new
SO_MAX_PACING_RATE socket option. From Eric Dumazet.
8) Make the initial autotuned send buffer sizing in TCP more closely
reflect actual needs, from Eric Dumazet.
9) Currently early socket demux only happens for TCP sockets, but we
can do it for connected UDP sockets too. Implementation from Shawn
Bohrer.
10) Refactor inet socket demux with the goal of improving hash demux
performance for listening sockets. With the main goals being able
to use RCU lookups on even request sockets, and eliminating the
listening lock contention. From Eric Dumazet.
11) The bonding layer has many demuxes in it's fast path, and an RCU
conversion was started back in 3.11, several changes here extend the
RCU usage to even more locations. From Ding Tianhong and Wang
Yufen, based upon suggestions by Nikolay Aleksandrov and Veaceslav
Falico.
12) Allow stackability of segmentation offloads to, in particular, allow
segmentation offloading over tunnels. From Eric Dumazet.
13) Significantly improve the handling of secret keys we input into the
various hash functions in the inet hashtables, TCP fast open, as
well as syncookies. From Hannes Frederic Sowa. The key fundamental
operation is "net_get_random_once()" which uses static keys.
Hannes even extended this to ipv4/ipv6 fragmentation handling and
our generic flow dissector.
14) The generic driver layer takes care now to set the driver data to
NULL on device removal, so it's no longer necessary for drivers to
explicitly set it to NULL any more. Many drivers have been cleaned
up in this way, from Jingoo Han.
15) Add a BPF based packet scheduler classifier, from Daniel Borkmann.
16) Improve CRC32 interfaces and generic SKB checksum iterators so that
SCTP's checksumming can more cleanly be handled. Also from Daniel
Borkmann.
17) Add a new PMTU discovery mode, IP_PMTUDISC_INTERFACE, which forces
using the interface MTU value. This helps avoid PMTU attacks,
particularly on DNS servers. From Hannes Frederic Sowa.
18) Use generic XPS for transmit queue steering rather than internal
(re-)implementation in virtio-net. From Jason Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
random32: add test cases for taus113 implementation
random32: upgrade taus88 generator to taus113 from errata paper
random32: move rnd_state to linux/random.h
random32: add prandom_reseed_late() and call when nonblocking pool becomes initialized
random32: add periodic reseeding
random32: fix off-by-one in seeding requirement
PHY: Add RTL8201CP phy_driver to realtek
xtsonic: add missing platform_set_drvdata() in xtsonic_probe()
macmace: add missing platform_set_drvdata() in mace_probe()
ethernet/arc/arc_emac: add missing platform_set_drvdata() in arc_emac_probe()
ipv6: protect for_each_sk_fl_rcu in mem_check with rcu_read_lock_bh
vlan: Implement vlan_dev_get_egress_qos_mask as an inline.
ixgbe: add warning when max_vfs is out of range.
igb: Update link modes display in ethtool
netfilter: push reasm skb through instead of original frag skbs
ip6_output: fragment outgoing reassembled skb properly
MAINTAINERS: mv643xx_eth: take over maintainership from Lennart
net_sched: tbf: support of 64bit rates
ixgbe: deleting dfwd stations out of order can cause null ptr deref
ixgbe: fix build err, num_rx_queues is only available with CONFIG_RPS
...
The MOXA UC-711X hardware(s) has an ethernet controller that seem
to be developed internally. The IC used is "RTL8201CP".
This patch adds an MDIO driver which handles the MII bus.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_attrs field of struct bus_type is going away soon, dev_groups
should be used instead. This converts the MDIO bus code to use the
correct field.
Cc: David S. Miller <davem@davemloft.net>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Nick Bowler <nbowler@elliptictech.com>
Cc: <netdev@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
removes following warnings-
drivers/net/phy/marvell.c:37: WARNING: Use #include <linux/io.h> instead of <asm/io.h>
drivers/net/phy/marvell.c:39: WARNING: Use #include <linux/uaccess.h> instead of <asm/uaccess.h>
Signed-off-by: Avinash Kumar <avi.kp.137@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When WOL is enabled, the chip can't be put into power-down (BMCR_PDOWN)
mode, as that will also switch off the MAC, which consequently leads to
a link loss.
Use BMCR_ISOLATE in that case, which will at least save us some
milliamperes in comparison to normal operation mode.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just a cosmetic cleanup.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All supported Micrel PHYs implement the standard "power down" bit 11 of BMCR,
so this patch adds support using the generic genphy_{suspend,resume} functions.
Signed-off-by: Patrice Vilchez <patrice.vilchez@atmel.com>
[b.brezillon@overkiz.com: adapt to newer kernel and generalize to other phys]
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
[nicolas.ferre@atmel.com: commit message modification]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clears following warnings :
WARNING: Use include <linux/io.h> instead of <asm/io.h>
WARNING: Use include <linux/uaccess.h> instead of <asm/uaccess.h>
Signed-off-by: Avinash Kumar <avi.kp.137@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data
using platform_device instead of using dev_{get,set}_drvdata()
with &pdev->dev, so we can directly pass a struct platform_device.
This is a purely cosmetic change.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_ioremap_resource instead of of_iomap() and devm_kzalloc()
instead of kmalloc() to make cleanup paths simpler. This patch also
fixes the resource leak caused by missing corresponding iounamp()
of the of_iomap().
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/iwlwifi/pcie/trans.c
include/linux/inetdevice.h
The inetdevice.h conflict involves moving the IPV4_DEVCONF values
into a UAPI header, overlapping additions of some new entries.
The iwlwifi conflict is a context overlap.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_set_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some boards require custom PHY configuration, for example due to trace
length differences. Add the ability to configure these registers in
order to get the PHY to function on boards that need it.
Because PHYs are auto-detected based on MDIO device IDs, allow PHY
configuration to be specified in the parent Ethernet device node if no
PHY device node is present.
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to fix a problem in the rtl8211 where the driver
wasn't properly enabled the interrupt on link change status.
it has to enable the ineterrupt on the bit 10 in the register 18
(INER).
Reported-by: Sharma Bhupesh <B45370@freescale.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ksz8873mll_read_status() is used only in this file.
Fix the following sparse warning:
drivers/net/phy/micrel.c:147:5: warning: symbol 'ksz8873mll_read_status' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current timeout check is comparing two constant values, so it won't
ever detect a timeout. This patch reworks the affected code a bit so it
has a chance at detecting timeouts correctly.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Just a bunch of small fixes and tidy ups:
1) Finish the "busy_poll" renames, from Eliezer Tamir.
2) Fix RCU stalls in IFB driver, from Ding Tianhong.
3) Linearize buffers properly in tun/macvtap zerocopy code.
4) Don't crash on rmmod in vxlan, from Pravin B Shelar.
5) Spinlock used before init in alx driver, from Maarten Lankhorst.
6) A sparse warning fix in bnx2x broke TSO checksums, fix from Dmitry
Kravkov.
7) Dummy and ifb driver load failure paths can oops, fixes from Tan
Xiaojun and Ding Tianhong.
8) Correct MTU calculations in IP tunnels, from Alexander Duyck.
9) Account all TCP retransmits in SNMP stats properly, from Yuchung
Cheng.
10) atl1e and via-rhine do not handle DMA mapping failures properly,
from Neil Horman.
11) Various equal-cost multipath route fixes in ipv6 from Hannes
Frederic Sowa"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (36 commits)
ipv6: only static routes qualify for equal cost multipathing
via-rhine: fix dma mapping errors
atl1e: fix dma mapping warnings
tcp: account all retransmit failures
usb/net/r815x: fix cast to restricted __le32
usb/net/r8152: fix integer overflow in expression
net: access page->private by using page_private
net: strict_strtoul is obsolete, use kstrtoul instead
drivers/net/ieee802154: don't use devm_pinctrl_get_select_default() in probe
drivers/net/ethernet/cadence: don't use devm_pinctrl_get_select_default() in probe
drivers/net/can/c_can: don't use devm_pinctrl_get_select_default() in probe
net/usb: add relative mii functions for r815x
net/tipc: use %*phC to dump small buffers in hex form
qlcnic: Adding Maintainers.
gre: Fix MTU sizing check for gretap tunnels
pkt_sched: sch_qfq: remove forward declaration of qfq_update_agg_ts
pkt_sched: sch_qfq: improve efficiency of make_eligible
gso: Update tunnel segmentation to support Tx checksum offload
inet: fix spacing in assignment
ifb: fix oops when loading the ifb failed
...
Pull MIPS updates from Ralf Baechle:
"MIPS updates:
- All the things that didn't make 3.10.
- Removes the Windriver PPMC platform. Nobody will miss it.
- Remove a workaround from kernel/irq/irqdomain.c which was there
exclusivly for MIPS. Patch by Grant Likely.
- More small improvments for the SEAD 3 platform
- Improvments on the BMIPS / SMP support for the BCM63xx series.
- Various cleanups of dead leftovers.
- Platform support for the Cavium Octeon-based EdgeRouter Lite.
Two large KVM patchsets didn't make it for this pull request because
their respective authors are vacationing"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
MIPS: SEAD3: Disable L2 cache on SEAD-3.
MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
MIPS: BCM63xx: Add SMP support to prom.c
MIPS: define write{b,w,l,q}_relaxed
MIPS: Expose missing pci_io{map,unmap} declarations
MIPS: Malta: Update GCMP detection.
Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
MIPS: APSP: Remove <asm/kspd.h>
SSB: Kconfig: Amend SSB_EMBEDDED dependencies
MIPS: microMIPS: Fix improper definition of ISA exception bit.
MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
MIPS: Declare emulate_load_store_microMIPS as a static function.
MIPS: Fix typos and cleanup comment
MIPS: Cleanup indentation and whitespace
MIPS: BMIPS: support booting from physical CPU other than 0
MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
MIPS: GIC: Fix gic_set_affinity infinite loop
MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
...
at803x supports Atheros 8030, 8031 and 8035 PHYs. 8031 was missing from
the mdio device id table.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"This is a re-do of the net-next pull request for the current merge
window. The only difference from the one I made the other day is that
this has Eliezer's interface renames and the timeout handling changes
made based upon your feedback, as well as a few bug fixes that have
trickeled in.
Highlights:
1) Low latency device polling, eliminating the cost of interrupt
handling and context switches. Allows direct polling of a network
device from socket operations, such as recvmsg() and poll().
Currently ixgbe, mlx4, and bnx2x support this feature.
Full high level description, performance numbers, and design in
commit 0a4db187a9 ("Merge branch 'll_poll'")
From Eliezer Tamir.
2) With the routing cache removed, ip_check_mc_rcu() gets exercised
more than ever before in the case where we have lots of multicast
addresses. Use a hash table instead of a simple linked list, from
Eric Dumazet.
3) Add driver for Atheros CQA98xx 802.11ac wireless devices, from
Bartosz Markowski, Janusz Dziedzic, Kalle Valo, Marek Kwaczynski,
Marek Puzyniak, Michal Kazior, and Sujith Manoharan.
4) Support reporting the TUN device persist flag to userspace, from
Pavel Emelyanov.
5) Allow controlling network device VF link state using netlink, from
Rony Efraim.
6) Support GRE tunneling in openvswitch, from Pravin B Shelar.
7) Adjust SOCK_MIN_RCVBUF and SOCK_MIN_SNDBUF for modern times, from
Daniel Borkmann and Eric Dumazet.
8) Allow controlling of TCP quickack behavior on a per-route basis,
from Cong Wang.
9) Several bug fixes and improvements to vxlan from Stephen
Hemminger, Pravin B Shelar, and Mike Rapoport. In particular,
support receiving on multiple UDP ports.
10) Major cleanups, particular in the area of debugging and cookie
lifetime handline, to the SCTP protocol code. From Daniel
Borkmann.
11) Allow packets to cross network namespaces when traversing tunnel
devices. From Nicolas Dichtel.
12) Allow monitoring netlink traffic via AF_PACKET sockets, in a
manner akin to how we monitor real network traffic via ptype_all.
From Daniel Borkmann.
13) Several bug fixes and improvements for the new alx device driver,
from Johannes Berg.
14) Fix scalability issues in the netem packet scheduler's time queue,
by using an rbtree. From Eric Dumazet.
15) Several bug fixes in TCP loss recovery handling, from Yuchung
Cheng.
16) Add support for GSO segmentation of MPLS packets, from Simon
Horman.
17) Make network notifiers have a real data type for the opaque
pointer that's passed into them. Use this to properly handle
network device flag changes in arp_netdev_event(). From Jiri
Pirko and Timo Teräs.
18) Convert several drivers over to module_pci_driver(), from Peter
Huewe.
19) tcp_fixup_rcvbuf() can loop 500 times over loopback, just use a
O(1) calculation instead. From Eric Dumazet.
20) Support setting of explicit tunnel peer addresses in ipv6, just
like ipv4. From Nicolas Dichtel.
21) Protect x86 BPF JIT against spraying attacks, from Eric Dumazet.
22) Prevent a single high rate flow from overruning an individual cpu
during RX packet processing via selective flow shedding. From
Willem de Bruijn.
23) Don't use spinlocks in TCP md5 signing fast paths, from Eric
Dumazet.
24) Don't just drop GSO packets which are above the TBF scheduler's
burst limit, chop them up so they are in-bounds instead. Also
from Eric Dumazet.
25) VLAN offloads are missed when configured on top of a bridge, fix
from Vlad Yasevich.
26) Support IPV6 in ping sockets. From Lorenzo Colitti.
27) Receive flow steering targets should be updated at poll() time
too, from David Majnemer.
28) Fix several corner case regressions in PMTU/redirect handling due
to the routing cache removal, from Timo Teräs.
29) We have to be mindful of ipv4 mapped ipv6 sockets in
upd_v6_push_pending_frames(). From Hannes Frederic Sowa.
30) Fix L2TP sequence number handling bugs, from James Chapman."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1214 commits)
drivers/net: caif: fix wrong rtnl_is_locked() usage
drivers/net: enic: release rtnl_lock on error-path
vhost-net: fix use-after-free in vhost_net_flush
net: mv643xx_eth: do not use port number as platform device id
net: sctp: confirm route during forward progress
virtio_net: fix race in RX VQ processing
virtio: support unlocked queue poll
net/cadence/macb: fix bug/typo in extracting gem_irq_read_clear bit
Documentation: Fix references to defunct linux-net@vger.kernel.org
net/fs: change busy poll time accounting
net: rename low latency sockets functions to busy poll
bridge: fix some kernel warning in multicast timer
sfc: Fix memory leak when discarding scattered packets
sit: fix tunnel update via netlink
dt:net:stmmac: Add dt specific phy reset callback support.
dt:net:stmmac: Add support to dwmac version 3.610 and 3.710
dt:net:stmmac: Allocate platform data only if its NULL.
net:stmmac: fix memleak in the open method
ipv6: rt6_check_neigh should successfully verify neigh if no NUD information are available
net: ipv6: fix wrong ping_v6_sendmsg return value
...
Pull workqueue changes from Tejun Heo:
"Surprisingly, Lai and I didn't break too many things implementing
custom pools and stuff last time around and there aren't any follow-up
changes necessary at this point.
The only change in this pull request is Viresh's patches to make some
per-cpu workqueues to behave as unbound workqueues dependent on a boot
param whose default can be configured via a config option. This leads
to higher processing overhead / lower bandwidth as more work items are
bounced across CPUs; however, it can lead to noticeable powersave in
certain configurations - ~10% w/ idlish constant workload on a
big.LITTLE configuration according to Viresh.
This is because per-cpu workqueues interfere with how the scheduler
perceives whether or not each CPU is idle by forcing pinned tasks on
them, which makes the scheduler's power-aware scheduling decisions
less effective.
Its effectiveness is likely less pronounced on homogenous
configurations and this type of optimization can probably be made
automatic; however, the changes are pretty minimal and the affected
workqueues are clearly marked, so it's an easy gain for some
configurations for the time being with pretty unintrusive changes."
* 'for-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
fbcon: queue work on power efficient wq
block: queue work on power efficient wq
PHYLIB: queue work on system_power_efficient_wq
workqueue: Add system wide power_efficient workqueues
workqueues: Introduce new flag WQ_POWER_EFFICIENT for power oriented workqueues
Merge 'net' bug fixes into 'net-next' as we have patches
that will build on top of them.
This merge commit includes a change from Emil Goode
(emilgoode@gmail.com) that fixes a warning that would
have been introduced by this merge. Specifically it
fixes the pingv6_ops method ipv6_chk_addr() to add a
"const" to the "struct net_device *dev" argument and
likewise update the dummy_ipv6_chk_addr() declaration.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for Atheros 8031 phy driver.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for RGMII TX delay configuration on Atheros 803X,
this can be enabled in debug registers. With this patch,
PHY_INTERFACE_MODE_RGMII_TXID modes are now supported.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WOL is initilized in phy config_init, but there are standard apis
(set_wol/get_wol) for WOL in phy frame work. So this patch moves
WOL specific code from config_init to wol standard apis.
Cc: Matus Ujhelyi <ujhelyi.m@gmail.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of phy_drivers_register/phy_drivers_unregister to register/unregister
multiple phy drivers in a single module.
Cc: Matus Ujhelyi <ujhelyi.m@gmail.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a separate driver for the MDIO interface of the
Allwinner ethernet controllers.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for this new phy ID.
Signed-off-by: Rick Hoover <RHoover@digilentinc.com>
Signed-off-by: Steven Wang <steven.wang@digilentinc.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This phy is on Xilinx ZC702 zynq development board.
Signed-off-by: Anirudha Sarangi <anirudh@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use macros from linux/marvell_phy.h instead of duplicate
magic phy ID in the driver.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Remove trailing white space
- Remove spaces before tag
- Fix comments
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy_init_eee has to exit with an error when the
local device and its link partner both do not support EEE.
So this patch fixes a problem when verify this.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
module_spi_driver() removes some boilerplate and makes the code
simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Broadcom BCM63xx PHY driver is for the SoC internal PHYs, flag these
as internal PHY devices.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
libphy currently always reports a PHY as an external transceiver from
the ethtool output. This is inaccurate, because some drivers should be
able to tell that a PHY device is an internal transceiver of an Ethernet
MAC. Add a new flag (PHY_IS_INTERNAL) which can be set by PHY drivers
just like other flags, and a corresponding helper: phy_is_internal()
which can be used by networking drivers to query if a given
PHY device is internal.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is currently no way for an Ethernet MAC driver servicing PHY link
interrupts to notify this to the PHY state machine without defining its
own state machine. Since most drivers are not so special, introduce a
helper: phy_mac_interrupt() which can be called from a link up/down
interrupt routine to update the PHY state machine. To avoid code
duplication some refactoring has been done to expose the workqueue and
its corresponding callback internally.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a PHY device is registered with the special IRQ value
PHY_IGNORE_INTERRUPT (-2) it will not properly be handled by the PHY
library:
- it continues to poll its register, while we do not want this
because such PHY link events or register changes are serviced by an
Ethernet MAC
- it will still try to configure PHY interrupts at the PHY level, such
interrupts do not exist at the PHY but at the MAC level
- the state machine only handles PHY_POLL, but should also handle
PHY_IGNORE_INTERRUPT similarly
This patch updates the PHY state machine and initialization paths to
account for the specific PHY_IGNORE_INTERRUPT. Based on an earlier patch
by Thomas Petazzoni, and reworked to add the missing bits. Add a helper
phy_interrupt_is_valid() which specifically tests for a PHY interrupt
not to be PHY_POLL or PHY_IGNORE_INTERRUPT and use it throughout the
code.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phylib uses workqueues for multiple purposes. There is no real dependency of
scheduling these on the cpu which scheduled them.
On a idle system, it is observed that and idle cpu wakes up many times just to
service this work. It would be better if we can schedule it on a cpu which the
scheduler believes to be the most appropriate one.
This patch replaces system_wq with system_power_efficient_wq for PHYLIB.
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any valid
cases for enableing GENERIC_GPIO without GPIOLIB, even though it is
possible to do so which has been causing confusion and breakage. This
branch does the work to completely eliminate GENERIC_GPIO.
However, it is not trivial to just create a branch to remove it. Over
the course of the v3.9 cycle more code referencing GENERIC_GPIO has been
added to linux-next that conflicts with this branch. The following must
be done to resolve the conflicts when merging this branch into mainline:
* "git grep CONFIG_GENERIC_GPIO" should return 0 hits. Matches should be
replaced with CONFIG_GPIOLIB
* "git grep '\bGENERIC_GPIO\b'" should return 1 hit in the Chinese
documentation.
* Selectors of GENERIC_GPIO should be turned into selectors of GPIOLIB
* definitions of the option in architecture Kconfig code should be deleted.
Stephen has 3 merge fixup patches[1] that do the above. They are currently
applicable on mainline as of May 2nd.
[1] http://www.mail-archive.com/linux-kernel@vger.kernel.org/msg428056.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJRifUnAAoJEEFnBt12D9kBs2YP/0U6+ia+xYvkVaJc28PDVIzn
OReZNcJOYU8D5voxz0voaRD0EdcPwjbMu9Kp9aXMHlk4VxevF+8jCc/us0bIjtO1
VcB5VmSCIhMhxdnBlum11Mk7Vr5MCweyl9NBsypnPt8cl4obMBZHf2yzoodFktNb
wtyYlOb6FALtc6iDbOO6dG3w9F7FAOLvskUFzdv89m8mupTsBu9jw9NqFDbJHOex
rxq0Sdd+kWF/nkJVcV5Y6jIdletRlhpipefMJ9diexreHvwqh+c4kJEYZaXgB5+m
ha95cPbReK1d+RqzM3A8d4irzSVSmq4k7ijI6QkFOr48+AH7XsgKv5so885LKzMN
IIXg2Phm9i0H8+ecEvhcc4oIYBHJiEKK54Y0qUD9dqbFoDGPTCSqMHdSSMbpAY+J
bIIXlVzj1En3PPNUJLPt8q8Qz6WxCT9mDST3QSGYnD4o90HT+1R9j92RxGL6McOq
rUOyJDwmzFvpBvKK4raGdOU435M+ps2NPKKNIRaIGQPPY9rM1kN4YqvhXukEsC9L
3a3+3cQLh7iKxBHncxeQsJfethP1CPkJnzvF9r+ZZLf2rcPH4pbQIE2uO0XnX/nd
5/DKi0nGgAJ//GMMzdo3RiOA5zGFjIZ/KMvfhQldpP6qFJRhqdGi6FPlAcwr1z1n
YnCByPwwlvfC4LTXFOGL
=xodc
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull removal of GENERIC_GPIO from Grant Likely:
"GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any
valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it
is possible to do so which has been causing confusion and breakage.
This branch does the work to completely eliminate GENERIC_GPIO."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
gpio: update gpio Chinese documentation
Remove GENERIC_GPIO config option
Convert selectors of GENERIC_GPIO to GPIOLIB
blackfin: force use of gpiolib
m68k: coldfire: use gpiolib
mips: pnx833x: remove requirement for GENERIC_GPIO
openrisc: default GENERIC_GPIO to false
avr32: default GENERIC_GPIO to false
xtensa: remove explicit selection of GENERIC_GPIO
sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB
powerpc: remove redundant GENERIC_GPIO selection
unicore32: default GENERIC_GPIO to false
unicore32: remove unneeded select GENERIC_GPIO
arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB
arm: remove redundant GENERIC_GPIO selection
mips: alchemy: require gpiolib
mips: txx9: change GENERIC_GPIO to GPIOLIB
mips: loongson: use GPIO driver on CONFIG_GPIOLIB
mips: remove redundant GENERIC_GPIO select
GENERIC_GPIO is now equivalent to GPIOLIB and features that depended on
GENERIC_GPIO can now depend on GPIOLIB to allow removal of this option.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
The Octeon SMI/MDIO interfaces can do clause 45 communications, so
implement this in the driver.
Also fix some comment formatting to make it consistent and to comply
with the netdev style.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of fixed speed set up for a NIC (e.g. ethtool -s eth0 autoneg off speed
100 duplex full) with an ethernet cable plugged off, the mentioned algorithm
slows down a NIC speed, so further cable hook-up leads to nonoperable link state.
Signed-off-by: Kirill Kapranov <kapranoff@inbox.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
module_platform_driver macro removes some boilerplate and
simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: David Daney <ddaney@caviumnetworks.com>
Acked-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
module_platform_driver macro removes some boilerplate and
simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This has been tested on a qnap TS-119P II. Note that enabling WOL with
"ethtool -s eth0 wol g" is not enough; you also need to tell the PIC
microcontroller inside the qnap that WOL should be enabled by sending
0xF2 with qcontrol(1) and you have to disable EUP ("Energy-using
Products", a European power-saving thing) by sending 0xF4.
Signed-off-by: Michael Stapelberg <michael@stapelberg.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows ethernet drivers (such as the mv643xx_eth) to support
Wake on LAN on platforms where PHY registers have to be configured
for Wake on LAN (e.g. the Marvell Kirkwood based qnap TS-119P II).
Signed-off-by: Michael Stapelberg <michael@stapelberg.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag MICREL_PHY_50MHZ_CLK is not of exclusive use of KSZ8051
model. At least KSZ8021 and KSZ8031 models also use it.
This patch moves the handling of this and future flags to a
separate function so that the different PHY models can call it on
their init function, if needed.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Micrel PHY KSZ8031 is similar to KSZ8021 and also requires the special
initialization of "Operation Mode Strap Override" in reg 0x16
introduced in 212ea99 (phy/micrel: Implement support for KSZ8021).
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function is only used in this file, should be static and not
an exported symbol.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phyter KSZ9021 has hardware bug. If asymmetric pause is enabled,
then it is necessary to disconnect and then reconnect the ethernet
cable to get the phyter working. The solution is to disable the
asymmetric pause.
Signed-off-by: Vlastimil Kosar <ikosar@fit.vutbr.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix memory leak in phy_device_free() for the case when phy_device*
returned by phy_device_create() is not registered in the system.
Bug description:
phy_device_create() sets name of kobject using dev_set_name(), which
allocates memory using kvasprintf(), but this memory isn't freed if
the underlying device isn't registered properly, because kobject_cleanup()
is not called in that case. This can happen (and actually is happening on
our machines) if phy_device_register(), called by mdiobus_scan(), fails.
Patch description:
Embedded struct device is initialized in phy_device_create() and it
counterpart phy_device_free() just drops one reference to the device,
which leads to proper deinitialization including releasing the kobject
name memory.
Signed-off-by: Petr Malat <oss@malat.biz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull s390 update from Martin Schwidefsky:
"The most prominent change in this patch set is the software dirty bit
patch for s390. It removes __HAVE_ARCH_PAGE_TEST_AND_CLEAR_DIRTY and
the page_test_and_clear_dirty primitive which makes the common memory
management code a bit less obscure.
Heiko fixed most of the PCI related fallout, more often than not
missing GENERIC_HARDIRQS dependencies. Notable is one of the 3270
patches which adds an export to tty_io to be able to resize a tty.
The rest is the usual bunch of cleanups and bug fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (42 commits)
s390/module: Add missing R_390_NONE relocation type
drivers/gpio: add missing GENERIC_HARDIRQ dependency
drivers/input: add couple of missing GENERIC_HARDIRQS dependencies
s390/cleanup: rename SPP to LPP
s390/mm: implement software dirty bits
s390/mm: Fix crst upgrade of mmap with MAP_FIXED
s390/linker skript: discard exit.data at runtime
drivers/media: add missing GENERIC_HARDIRQS dependency
s390/bpf,jit: add vlan tag support
drivers/net,AT91RM9200: add missing GENERIC_HARDIRQS dependency
iucv: fix kernel panic at reboot
s390/Kconfig: sort list of arch selected config options
phylib: remove !S390 dependeny from Kconfig
uio: remove !S390 dependency from Kconfig
dasd: fix sysfs cleanup in dasd_generic_remove
s390/pci: fix hotplug module init
s390/pci: cleanup clp page allocation
s390/pci: cleanup clp inline assembly
s390/perf: cpum_cf: fallback to software sampling events
s390/mm: provide PAGE_SHARED define
...
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
Pull networking update from David Miller:
1) Checkpoint/restarted TCP sockets now can properly propagate the TCP
timestamp offset. From Andrey Vagin.
2) VMWARE VM VSOCK layer, from Andy King.
3) Much improved support for virtual functions and SR-IOV in bnx2x,
from Ariel ELior.
4) All protocols on ipv4 and ipv6 are now network namespace aware, and
all the compatability checks for initial-namespace-only protocols is
removed. Thanks to Tom Parkin for helping deal with the last major
holdout, L2TP.
5) IPV6 support in netpoll and network namespace support in pktgen,
from Cong Wang.
6) Multiple Registration Protocol (MRP) and Multiple VLAN Registration
Protocol (MVRP) support, from David Ward.
7) Compute packet lengths more accurately in the packet scheduler, from
Eric Dumazet.
8) Use per-task page fragment allocator in skb_append_datato_frags(),
also from Eric Dumazet.
9) Add support for connection tracking labels in netfilter, from
Florian Westphal.
10) Fix default multicast group joining on ipv6, and add anti-spoofing
checks to 6to4 and 6rd. From Hannes Frederic Sowa.
11) Make ipv4/ipv6 fragmentation memory limits more reasonable in modern
times, rearrange inet frag datastructures for better cacheline
locality, and move more operations outside of locking. From Jesper
Dangaard Brouer.
12) Instead of strict master <--> slave relationships, allow arbitrary
scenerios with "upper device lists". From Jiri Pirko.
13) Improve rate limiting accuracy in TBF and act_police, also from Jiri
Pirko.
14) Add a BPF filter netfilter match target, from Willem de Bruijn.
15) Orphan and delete a bunch of pre-historic networking drivers from
Paul Gortmaker.
16) Add TSO support for GRE tunnels, from Pravin B SHelar. Although
this still needs some minor bug fixing before it's %100 correct in
all cases.
17) Handle unresolved IPSEC states like ARP, with a resolution packet
queue. From Steffen Klassert.
18) Remove TCP Appropriate Byte Count support (ABC), from Stephen
Hemminger. This was long overdue.
19) Support SO_REUSEPORT, from Tom Herbert.
20) Allow locking a socket BPF filter, so that it cannot change after a
process drops capabilities.
21) Add VLAN filtering to bridge, from Vlad Yasevich.
22) Bring ipv6 on-par with ipv4 and do not cache neighbour entries in
the ipv6 routes, from YOSHIFUJI Hideaki.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1538 commits)
ipv6: fix race condition regarding dst->expires and dst->from.
net: fix a wrong assignment in skb_split()
ip_gre: remove an extra dst_release()
ppp: set qdisc_tx_busylock to avoid LOCKDEP splat
atl1c: restore buffer state
net: fix a build failure when !CONFIG_PROC_FS
net: ipv4: fix waring -Wunused-variable
net: proc: fix build failed when procfs is not configured
Revert "xen: netback: remove redundant xenvif_put"
net: move procfs code to net/core/net-procfs.c
qmi_wwan, cdc-ether: add ADU960S
bonding: set sysfs device_type to 'bond'
bonding: fix bond_release_all inconsistencies
b44: use netdev_alloc_skb_ip_align()
xen: netback: remove redundant xenvif_put
net: fec: Do a sanity check on the gpio number
ip_gre: propogate target device GSO capability to the tunnel device
ip_gre: allow CSUM capable devices to handle packets
bonding: Fix initialize after use for 3ad machine state spinlock
bonding: Fix race condition between bond_enslave() and bond_3ad_update_lacp_rate()
...
This patch replaces the horribly coded of_count_named_gpios() with a
call to of_count_phandle_with_args() which is far more efficient. This
also changes the return value of of_gpio_count() & of_gpio_named_count()
from 'unsigned int' to 'int' so that it can return an error code. All
the users of that function are fixed up to correctly handle a negative
return value.
v2: Split GPIO portion into a separate patch
Tested-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
All in-kernel users of class_find_device() don't really need mutable
data for match callback.
In two places (kernel/power/suspend_test.c, drivers/scsi/osd/osd_uld.c)
this patch changes match callbacks to use const search data.
The const is propagated to rtc_class_open() and power_supply_get_by_name()
parameters.
Note that there's a dev reference leak in suspend_test.c that's not
touched in this patch.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
alloc failures already get standardized OOM
messages and a dump_stack.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bring in the 'net' tree so that we can get some ipv4/ipv6 bug
fixes that some net-next work will build upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
Summary of changes:
.Newly added phys
-KSZ8081/KSZ8091, which has some phy ids.
-KSZ8061
-KSZ9031, which is Gigabit phy.
-KSZ886X, which has a switch function.
-KSZ8031, which has a same phy ids with KSZ8021.
Signed-off-by: David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the minimal driver to manage the
Realtek RTL8211E 10/100/1000 Transceivers.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the setting of the INTR pin that is
valid for IP101 A/G device and not for the IP1001.
Reported-by: Anunay Saxena <anunay.saxena@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like several other PHY devices which support RGMII, the IC+1001 allows
additional delays to by added to the RX_CLK and TX_CLK signals to
compensate for skew between the clock and data signals. Previously this
was always enabled, but this change makes use of the different RGMII
interface modes to allow the user to specify whether this should be
enabled.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the code that always enables copper/fiber autoselect,
ignoring the DIS_FC strapping pin. The default value for this
register is autoselect on anyway, and if you explicitly disable
autoselect via strapping you probably really don't want
autoselect.
Signed-off-by: Stef van Os <stef.van.os@prodrive.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flags argument of the phy_{attach,connect,connect_direct} functions
is then used to assign a struct phy_device dev_flags with its value.
All callers but the tg3 driver pass the flag 0, which results in the
underlying PHY drivers in drivers/net/phy/ not being able to actually
use any of the flags they would set in dev_flags. This patch gets rid of
the flags argument, and passes phydev->dev_flags to the internal PHY
library call phy_attach_direct() such that drivers which actually modify
a phy device dev_flags get the value preserved for use by the underlying
phy driver.
Acked-by: Kosta Zertsekel <konszert@marvell.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct a mistake made in the previous commit due to reckless
copy-and-pasting.
Signed-off-by: Patrick Trantham <patrick.trantham@fuel7.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __dev* removal patches for the network drivers ended up messing up
the function prototypes for a bunch of drivers. This patch fixes all of
them back up to be properly aligned.
Bonus is that this almost removes 100 lines of code, always a nice
surprise.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A SMSC PHY in power down mode can't be used.
If a SMSC PHY is in this mode in the config_init
stage, the mode "all capable" is set. So the PHY
could then be used.
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added functions for ack_interrupt and config_intr. Tested on an mpc5200b
powerpc board.
Signed-off-by: Stephan Gatzka <stephan.gatzka@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Conflicts:
drivers/net/wireless/iwlwifi/pcie/tx.c
Minor iwlwifi conflict in TX queue disabling between 'net', which
removed a bogus warning, and 'net-next' which added some status
register poking code.
Signed-off-by: David S. Miller <davem@davemloft.net>
this will allow to detect the link between the switch and the soc
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
When the mdio-gpio driver is probed via device trees, the platform
device id is set as -1, However the pdev->id is re-used as bus-id for
while creating mdio gpio bus.
So
For device tree case the mdio-gpio bus name appears as "gpio-ffffffff"
where as
for non-device tree case the bus name appears as "gpio-<bus-num>"
Which means the bus_id is fixed in device tree case, so we can't have
two mdio gpio buses via device trees. Assigning a logical bus number
via device tree solves the problem and the bus name is much consistent
with non-device tree bus name.
Without this patch
1. we can't support two mdio-gpio buses via device trees.
2. we should always pass gpio-ffffffff as bus name to phy_connect, very
different to non-device tree bus name.
So, setting up the bus_id via aliases from device tree is the right
solution and other drivers do similar thing.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch re-enables Energy Detect Power Down (EDPD) mode for the
LAN8710/LAN8720. EDPD mode was disabled in a previous commit,
(b629820d18), because it was causing the
PHY to not be able to detect a link when cold started without a cable
connected.
The LAN8710/LAN8720 requires a minimum of 2 link pulses within 64ms of
each other in order to set the ENERGYON bit and exit EDPD mode. If a
link partner does send the pulses within this interval, the PHY will
remained powered down.
This workaround will manually toggle the PHY on/off upon calls to
read_status in order to generate link test pulses if the link is down.
If a link partner is present, it will respond to the pulses, which will
cause the ENERGYON bit to be set and will cause the EDPD mode to be
exited.
Signed-off-by: Patrick Trantham <patrick.trantham@fuel7.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit aa731872f7.
As pointed out by Ben Hutchings, this change is not correct.
mdiobus_unregister() can't be called if the bus isn't registered yet,
however this change can result in situations which cause that to
happen.
Part of the confusion here revolves around the fact that the
callers of this module control registration/unregistration,
rather than the module itself.
Signed-off-by: David S. Miller <davem@davemloft.net>
Both these PHYs support interrupt generation on IC pin 32.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
Minor conflict between the BCM_CNIC define removal in net-next
and a bug fix added to net. Based upon a conflict resolution
patch posted by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a phy_id sysfs attribute to MDIO devices, containing the
32-bit PHY identifier reported by the device. This attribute can
be useful when debugging problems related to phy drivers. Other
enumerable buses already have similar attributes.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on commit b27393aecf
Calling mdiobus_free without calling mdiobus_unregister causes
BUG_ON(). This patch fixes the issue.
The semantic patch that found this issue(http://coccinelle.lip6.fr/):
// <smpl>
@@
expression E;
@@
... when != mdiobus_unregister(E);
+ mdiobus_unregister(E);
mdiobus_free(E);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver add support for wake over lan on AT803x phys.
Signed-off-by: Matus Ujhelyi <ujhelyi.m@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that of_mdio_find_bus() matches the prototype in the header (and
stop sparse complaining) by including the header with the prototype.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/team/team.c
drivers/net/usb/qmi_wwan.c
net/batman-adv/bat_iv_ogm.c
net/ipv4/fib_frontend.c
net/ipv4/route.c
net/l2tp/l2tp_netlink.c
The team, fib_frontend, route, and l2tp_netlink conflicts were simply
overlapping changes.
qmi_wwan and bat_iv_ogm were of the "use HEAD" variety.
With help from Antonio Quartulli.
Signed-off-by: David S. Miller <davem@davemloft.net>
The LAN8710/LAN8720 chips do have broken the "FlexPWR" smart power-saving
capability. Enabling it leads to the PHY not being able to detect Link when
cold-started without cable connected. Thus, make sure this is disabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christian Hohnstaedt <chohnstaedt@innominate.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds proper handling of the buggy revision A2 of LXT973 phy, adding
precautions linked to ERRATA Item 4:
Revision A2 of LXT973 chip randomly returns the contents of the previous even
register when you read a odd register regularly
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no such part as KS8001, KS8041 or KS8051. There are only
KSZ8001, KSZ8041 and KSZ8051. Rename these parts as such to match
the Micrel naming.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David J. Choi <david.choi@micrel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Linux ARM kernel <linux-arm-kernel@lists.infradead.org>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ8021 PHY was previously caught by KS8051, which is not correct.
This PHY needs additional setup if it is strapped for address 0. In such
case an reserved bit must be written in the 0x16, "Operation Mode Strap
Override" register. According to the KS8051 datasheet, that bit means
"PHY Address 0 in non-broadcast" and it indeed behaves as such on KSZ8021.
The issue where the ethernet controller (Freescale FEC) did not communicate
with network is fixed by writing this bit as 1.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David J. Choi <david.choi@micrel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTP Hardware Clock devices appear as class devices in sysfs. This patch
changes the registration API to use the parent device, clarifying the
clock's relationship to the underlying device.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the driver has no MODULE_LICENSE attribute in its source which
results in a kernel taint if I load this:
root@(none):~# modprobe bcm87xx
bcm87xx: module license 'unspecified' taints kernel.
Since the first lines of the source code clearly state:
* This file is subject to the terms and conditions of the GNU General
* Public License. See the file "COPYING" in the main directory of this
* archive for more details.
I think it's safe to add the MODULE_LICENSE("GPL") macro and thus remove
the kernel taint.
Cc: stable@vger.kernel.org
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdio-mux-mmioreg.c uses function of_address_to_resource(), which is defined
in linux/of_address.h. This fixes a compilation error:
drivers/net/phy/mdio-mux-mmioreg.c: In function 'mdio_mux_mmioreg_probe':
drivers/net/phy/mdio-mux-mmioreg.c:83:2: error: implicit declaration of
function 'of_address_to_resource'
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for an MDIO bus multiplexer controlled by a simple memory-mapped
device, like an FPGA. The device must be memory-mapped and contain only
8-bit registers (which keeps things simple).
Tested on a Freescale P5020DS board which uses the "PIXIS" FPGA attached
to the localbus.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up the way device tree support is added in mdio-gpio
driver. I found lot of code duplication which is not necessary.
Also strangely a new platform driver was also introduced for device tree
support. All this forced me to do this cleanup patch.
After this patch, the driver probe checks the of_node pointer to get the
data from device tree.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The helper functions which translate IEEE MDIO Manageable Device (MMD)
Energy-Efficient Ethernet (EEE) registers 3.20, 7.60 and 7.61 to and from
the comparable ethtool supported/advertised settings will be needed by
drivers other than those in PHYLIB (e.g. e1000e in a follow-on patch).
In the same fashion as similar translation functions in linux/mii.h, move
these functions from the PHYLIB core to the linux/mdio.h header file so the
code will not have to be duplicated in each driver needing MMD-to-ethtool
(and vice-versa) translations. The function and some variable names have
been renamed to be more descriptive.
Not tested on the only hardware that currently calls the related functions,
stmmac, because I don't have access to any. Has been compile tested and
the translations have been tested on a locally modified version of e1000e.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mdio-mux driver scans all child mdio nodes, without regard to whether
the node is actually used. Some device trees include all possible
mdio-mux nodes and rely on the boot loader to disable those that are not
present, based on some run-time configuration. Those nodes need to be
skipped.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devm_kfree should not have to be explicitly used.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,d;
@@
x = devm_kzalloc(...)
...
?-devm_kfree(d,x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull MIPS updates from Ralf Baechle:
"More hardware support across the field including a bunch of device
drivers. The highlight however really are further steps towards
device tree.
This has been sitting in -next for ages. All MIPS _defconfigs have
been tested to boot or where I don't have hardware available, to at
least build fine."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (77 commits)
MIPS: Loongson 1B: Add defconfig
MIPS: Loongson 1B: Add board support
MIPS: Netlogic: early console fix
MIPS: Netlogic: Fix indentation of smpboot.S
MIPS: Netlogic: remove cpu_has_dc_aliases define for XLP
MIPS: Netlogic: Remove unused pcibios_fixups
MIPS: Netlogic: Add XLP SoC devices in FDT
MIPS: Netlogic: Add IRQ mappings for more devices
MIPS: Netlogic: USB support for XLP
MIPS: Netlogic: XLP PCIe controller support.
MIPS: Netlogic: Platform changes for XLR/XLS I2C
MIPS: Netlogic: Platform NAND/NOR flash support
MIPS: Netlogic: Platform changes for XLS USB
MIPS: Netlogic: Remove NETLOGIC_ prefix
MIPS: Netlogic: SMP wakeup code update
MIPS: Netlogic: Update comments in smpboot.S
MIPS: BCM63XX: Add 96328avng reference board
MIPS: Expose PCIe drivers for MIPS
MIPS: BCM63XX: Add PCIe Support for BCM6328
MIPS: BCM63XX: Move the PCI initialization into its own function
...
Florian Fainelli