When a new page flip is requested, we need to both queue an unpin for
the current framebuffer, and also increment the flip pending count on
the newly submitted buffer.
At flip finish time, we need to unpin the old fb and decrement the flip
pending count on the new buffer.
The old code was conflating the two, and led to hangs when new direct
rendered apps were started, replacing the existing frame buffer. This
patch splits out the buffers and prevents the hangs.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
On 945, we need to avoid entering self-refresh if the compressor is
busy, or we may cause display FIFO underruns leading to ugly flicker.
Fixes fdo bug #24314, kernel bug #15043.
Tested-by: Alexander Lam <lambchop468@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Julien Cristau <jcristau@debian.org> (fd.o #25371)
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
An untiled framebuffer must be aligned to 64k. This is normally handled
by intel_pin_and_fence_fb_obj(), but the intelfb_create() likes to be
different and do the pinning itself. However, it aligns the buffer
object incorrectly for pre-i965 chipsets causing a PGTBL_ERR when it is
installed onto the output.
Fixes:
KMS error message while initializing modesetting -
render error detected: EIR: 0x10 [i915]
http://bugs.freedesktop.org/show_bug.cgi?id=22936
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
In associated state, when bringing an interface down, existing
BA sessions are torn down. When this is in progress, nothing
prevents mac80211 from accepting another BA session start request.
Use a new station flag to fix this.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for using the libertas_tf driver on a managed
or ad-hoc network.
Signed-off-by: Deepak Saxena <dsaxena@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before changing the status of a buffer with a pending write we will await
upon a new flush for that buffer. So we can take advantage of any flushes
posted whilst the buffer is active and pending processing by the GPU, by
clearing its write_domain and updating its last_rendering_seqno -- thus
saving a potential flush in deep queues and improves flushing behaviour
upon eviction for both GTT space and fences.
In order to reduce the time spent searching the active list for matching
write_domains, we move those to a separate list whose elements are
the buffers belong to the active/flushing list with pending writes.
Orignal patch by Chris Wilson <chris@chris-wilson.co.uk>, forward-ported
by me.
In addition to better performance, this also fixes a real bug. Before
this changes, i915_gem_evict_everything didn't work as advertised. When
the gpu was actually busy and processing request, the flush and subsequent
wait would not move active and dirty buffers to the inactive list, but
just to the flushing list. Which triggered the BUG_ON at the end of this
function. With the more tight dirty buffer tracking, all currently busy and
dirty buffers get moved to the inactive list by one i915_gem_flush operation.
I've left the BUG_ON I've used to prove this in there.
References:
Bug 25911 - 2.10.0 causes kernel oops and system hangs
http://bugs.freedesktop.org/show_bug.cgi?id=25911
Bug 26101 - [i915] xf86-video-intel 2.10.0 (and git) triggers kernel oops
within seconds after login
http://bugs.freedesktop.org/show_bug.cgi?id=26101
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Adam Lantos <hege@playma.org>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
The patch that adds cpu_probe_vmbits is erroneously writing to reserved
bit 12. Since we are really only probing high bits, don't write this bit
with a one.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Patchwork: http://patchwork.linux-mips.org/patch/949/
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Test the value that was just allocated rather than the previously tested one.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
expression *x;
expression e;
identifier l;
@@
if (x == NULL || ...) {
... when forall
return ...; }
... when != goto l;
when != x = e
when != &x
*x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
To: linux-mips@linux-mips.org
To: linux-kernel@vger.kernel.org
To: kernel-janitors@vger.kernel.org
Patchwork: http://patchwork.linux-mips.org/patch/945/
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
cpu_cache_init and the things it calls should all be __cpuinit instead
of __devinit.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/938/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
RTC support was rewritten but the defconfig files were not updated. Enable
IPv6 support which for some folks already is a must have. Assign useful
values to other new options.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As reported by Maxime Bizon, the commit "MIPS: PowerTV: Fix support for
timer interrupts with > 64 external IRQs" have broken the r4k timer
since it didn't initialize the cp0_compare_irq_shift variable used in
c0_compare_int_pending() on the architectures whose cpu_has_mips_r2 is
false.
This patch fixes it via initializing the cp0_compare_irq_shift as the
cp0_compare_irq used in the old c0_compare_int_pending().
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: David VomLehn <dvomlehn@cisco.com>
Cc: mbizon@freebox.fr
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/922/
Tested-by: Shane McDonald <mcdonald.shane@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The hardware needs to know what type of frames are being
sent in order to fill in various fields, for example the
timestamp in probe responses (before this patch, it was
always 0). Set it correctly when initializing the TX
descriptor.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Got Ironlake DPLL parameter table, which reflects the hardware
optimized values. So this one trys to list DPLL parameters for
different output types, should potential fix clock issue seen
on new Arrandale CPUs.
This fixes DPLL setting failure on one 1920x1080 dual channel
LVDS for Ironlake. Test has also been made on LVDS panels with
smaller size and CRT/HDMI/DP ports for different monitors on
their all supported modes.
Update:
- Change name of double LVDS to dual LVDS.
- Fix SSC 120M reference clock to use the right range.
Cc: CSJ <changsijay@gmail.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
i.MX51 babbage board has a FEC ethernet controller
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The i.MX51 babbage board has a FEC ethernet controller with this phy.
In the long term we should resurrect the phylib patches for fec.
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fec driver was enabling receive buffer descriptor without allocating
the buffers. Make sure the buffer descriptors are initialized to not
start receiving packets.
Open also calls fec_restart after the rx buffers are allocated. With the code
in fec_restart, it zeroes out the buffer descriptors that have just been
setup.
Signed-off-by: Rob Herring <r.herring@freescale.com>
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert the following change from commit 6f8372b6 ("RDMA/cm: fix
loopback address support")
The defined behavior of rdma_bind_addr is to associate an RDMA
device with an rdma_cm_id, as long as the user specified a non-
zero address. (ie they weren't just trying to reserve a port)
Currently, if the loopback address is passed to rdma_bind_addr,
no device is associated with the rdma_cm_id. Fix this.
It turns out that important apps such as Open MPI depend on
rdma_bind_addr() NOT associating any RDMA device when binding to a
loopback address. Open MPI is being updated to deal with this, but at
least until a new Open MPI release is available, maintain the previous
behavior: allow rdma_bind_addr() to succeed, but do not bind to a
device.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some places in kernel need to iterate over a hlist in seq_file,
so provide some common helpers.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cohd_fin has already been verified not to be NULL, so the argument to
BUG_ON cannot be true.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
expression *x;
expression e;
identifier l;
@@
if (x == NULL || ...) {
... when forall
return ...; }
... when != goto l;
when != x = e
when != &x
*x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If submitting new buffer failed, a wrong descriptor gets completed and it
doesn't check, if a callback is at all defined, which can lead to an Oops. Fix
these bugs and make ipu_update_channel_buffer() void, because it never fails.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch fixes two potential races in the velocity driver:
* Move the ACK and error handler to the interrupt handler. This fixes a
potential race with shared interrupts when the other device interrupts
before the NAPI poll handler has finished. As the velocity driver hasn't
acked it's own interrupt, it will then steal the interrupt from the
other device.
* Use spin_lock_irqsave in velocity_poll. In the current code, the
interrupt handler will deadlock if e.g., the NAPI poll handler is
executing when an interrupt (for another device) comes in since it
tries to take the already held lock.
Also unlock the spinlock only after enabling the interrupt in
velocity_poll.
The error path is moved to the interrupt handler since this is where the
ISR is checked now.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Anders Grafstrom <anders.grafstrom@netinsight.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
velocity_set_coalesce touches ISR and some other sensitive registers not
covered by the rtnl lock, so take the velocity spinlock.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new RTL8187B device.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The platform data allocated with kmalloc() will become unreachable once
the init is complete, so it should be freed. The problem was discovered
by kmemleak.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The static initial tables are pretty large, and after the net
namespace has been instantiated, they just hang around for nothing.
This commit removes them and creates tables on-demand at runtime when
needed.
Size shrinks by 7735 bytes (x86_64).
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
The respective xt_table structures already have most of the metadata
needed for hook setup. Add a 'priority' field to struct xt_table so
that xt_hook_link() can be called with a reduced number of arguments.
So should we be having more tables in the future, it comes at no
static cost (only runtime, as before) - space saved:
6807373->6806555.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
The calls to ip6t_do_table only show minimal differences, so it seems
like a good cleanup to merge them to a single one too.
Space saving obtained by both patches: 6807725->6807373
("Total" column from `size -A`.)
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
This patch combines all the per-hook functions in a given table into
a single function. Together with the 2nd patch, further
simplifications are possible up to the point of output code reduction.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
md ioctls are now handled by the md driver itself, but mdadm
may call RAID_VERSION on other devices as well. Mark the command
as IGNORE_IOCTL so this fails silently rather than printing
an annoying message.
Reported-by: "Michael S. Tsirkin" <m.s.tsirkin@gmail.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'kvm-updates/2.6.33' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: PIT: control word is write-only
kvmclock: count total_sleep_time when updating guest clock
Export the symbol of getboottime and mmonotonic_to_bootbased
* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
avr32: clean up memory allocation in at32_add_device_mci
arch/avr32: Fix build failure for avr32 caused by typo
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: fix dentry hash calculation for case-insensitive mounts
[CIFS] Don't cache timestamps on utimes due to coarse granularity
[CIFS] Maximum username length check in session setup does not match
cifs: fix length calculation for converted unicode readdir names
[CIFS] Add support for TCP_NODELAY