So far, the required PLL's (PLL1/PLL2/PLL5) have been initialized
by boot loader and the kernel code defined fixed rates according
to those default configurations. Beginning with the USB PLL7 the
code started to initialize the PLL's itself (using imx_clk_pllv3).
However, since commit dc4805c2e7
(ARM: imx: remove ENABLE and BYPASS bits from clk-pllv3 driver)
imx_clk_pllv3 no longer takes care of the ENABLE and BYPASS bits,
hence the USB PLL were not configured correctly anymore.
This patch not only fixes those USB PLL's, but also makes use of
the imx_clk_pllv3 for all PLL's and alignes the code with the PLL
support of the i.MX6 series.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
- Two fixes for the Baytrail driver affecting IRQs and
output state in sysfs
- Use the linux-gpio mailing list also for pinctrl patches
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dbx2
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin-control fixes from Linus Walleij:
"This kernel cycle has been calm for both pin control and GPIO so far
but here are three pin control patches for you anyway, only really
dealing with Baytrail:
- Two fixes for the Baytrail driver affecting IRQs and output state
in sysfs
- Use the linux-gpio mailing list also for pinctrl patches"
* tag 'pinctrl-v3.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: baytrail: show output gpio state correctly on Intel Baytrail
pinctrl: use linux-gpio mailing list
pinctrl: baytrail: Clear DIRECT_IRQ bit
Pull CMA and DMA-mapping fixes from Marek Szyprowski:
"This contains important fixes for recently introduced highmem support
for default contiguous memory region used for dma-mapping subsystem"
* 'fixes-for-v3.18' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
mm, cma: make parameters order consistent in func declaration and definition
mm: cma: Use %pa to print physical addresses
mm: cma: Ensure that reservations never cross the low/high mem boundary
mm: cma: Always consider a 0 base address reservation as dynamic
mm: cma: Don't crash on allocation if CMA area can't be activated
It is safe to call notify disconnect when the usb core
thinks the device is disconnected.
This commit also fixes one bug found at below situation:
we have not enabled usb wakeup, we do system suspend when
there is an usb device at the port, after suspend, we plug out
the usb device, then plug in device again. At that time,
the nofity disconnect was not called at current code, as
the controller doesn't know the usb device was disconnected
during the suspend, but USB core knows the port has changed
during that periods.
So to fix this problem, and let the usb core call notify disconnect.
Cc: 3.17+ <stable@vger.kernel.org>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we notify disconnecting based on the usb device is existed
(port_dev->child, the child device at roothub is not NULL), we
need to notify connect after device has been registered.
This fixes a bug that do fast plug in/out test, and the notify_disconnect
is not called due to roothub child is NULL and the enumeration has failed.
Cc: v3.17+ <stable@vger.kernel.org>
Signed-off-by: Tony Zheng <Tony.Zheng@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These drives hang when receiving ATA12 commands, so set the US_FL_NO_ATA_1X
quirk to filter these out.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The switch back is limited to ULT even on HP. The contrary
finding arose by bad luck in BIOS versions for testing.
This fixes spontaneous resume from S3 on some HP laptops.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently this quirk is enabled for the model with the device id 0x0089, it
is needed for the 0x009b model, which is found on the Fujitsu Lifebook u904
as well.
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usbip driver was moved out of staging in 3.17-rc3 but the MAINTAINERS file
still has the old staging entry as well as the new one. Remove the old entry.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Functions fw5895_init() and config_autodelink_before_power_down() are used
only when CONFIG_PM is defined.
drivers/usb/storage/realtek_cr.c:699:13: warning: 'fw5895_init' defined but not used [-Wunused-function]
drivers/usb/storage/realtek_cr.c:629:12: warning: 'config_autodelink_before_power_down' defined but not used [-Wunused-function]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PLAT_S5P Kconfig symbol was removed in commit d78c16ccde
("ARM: SAMSUNG: Remove remaining legacy code"). There are still
some references left, fix that by replacing them with ARCH_S5PV210.
Fixes: d78c16ccde ("ARM: SAMSUNG: Remove remaining legacy code")
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just like some Seagate enclosures, these devices do not seem to grok ata
pass through commands.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Streams seem to be broken on the Asmedia 1042. An uas capable Seagate disk
which is known to work fine with other controllers causes the system to freeze
when connected over usb-3 with this controller, where as it works fine with
uas in usb-2 ports, indicating a problem with streams.
This is a bit bigger hammer then I would like to use for this, but for now it
will have to make do. I've ordered a pci-e usb controller card with an Asmedia
1042, once that arrives I'll try to get streams to work (with a quirk flag if
necessary) and then we can re-enable them. For now this at least makes uas
capable disk enclosures work again by forcing fallback to the usb-storage
driver.
Reported-by: Bogdan Mihalcea <bogdan.mihalcea@infim.ro>
Cc: Bogdan Mihalcea <bogdan.mihalcea@infim.ro>
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We wanted to print the version as (major).(minor) but because the shift
operation is higher precedence than the mask then we print
(minor).(minor).
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These drives hang when receiving ATA12 commands, so set the US_FL_NO_ATA_1X
quirk to filter these out.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes mass-storage devices using the Bulk-only transport will
mistakenly skip the data phase of a command. Rather than sending the
data expected by the host or sending a zero-length packet, they go
directly to the status phase and send the CSW.
This causes problems for usb-storage, for obvious reasons. The driver
will interpret the CSW as a short data transfer and will wait to
receive a CSW. The device won't have anything left to send, so the
command eventually times out.
The SCSI layer doesn't retry commands after they time out (this is a
relatively recent change). Therefore we should do our best to detect
a skipped data phase and handle it promptly.
This patch adds code to do that. If usb-storage receives a short
13-byte data transfer from the device, and if the first four bytes of
the data match the CSW signature, the driver will set the residue to
the full transfer length and interpret the data as a CSW.
This fixes Bugzilla #86611.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Tested-by: Paul Osmialowski <newchief@king.net.pl>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit fixes the following oops:
[10238.622067] scsi host3: uas_eh_bus_reset_handler start
[10240.766164] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd
[10245.779365] usb 3-4: device descriptor read/8, error -110
[10245.883331] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd
[10250.897603] usb 3-4: device descriptor read/8, error -110
[10251.058200] BUG: unable to handle kernel NULL pointer dereference at 0000000000000040
[10251.058244] IP: [<ffffffff815ac6e1>] xhci_check_streams_endpoint+0x91/0x140
<snip>
[10251.059473] Call Trace:
[10251.059487] [<ffffffff815aca6c>] xhci_calculate_streams_and_bitmask+0xbc/0x130
[10251.059520] [<ffffffff815aeb5f>] xhci_alloc_streams+0x10f/0x5a0
[10251.059548] [<ffffffff810a4685>] ? check_preempt_curr+0x75/0xa0
[10251.059575] [<ffffffff810a46dc>] ? ttwu_do_wakeup+0x2c/0x100
[10251.059601] [<ffffffff810a49e6>] ? ttwu_do_activate.constprop.111+0x66/0x70
[10251.059635] [<ffffffff815779ab>] usb_alloc_streams+0xab/0xf0
[10251.059662] [<ffffffffc0616b48>] uas_configure_endpoints+0x128/0x150 [uas]
[10251.059694] [<ffffffffc0616bac>] uas_post_reset+0x3c/0xb0 [uas]
[10251.059722] [<ffffffff815727d9>] usb_reset_device+0x1b9/0x2a0
[10251.059749] [<ffffffffc0616f42>] uas_eh_bus_reset_handler+0xb2/0x190 [uas]
[10251.059781] [<ffffffff81514293>] scsi_try_bus_reset+0x53/0x110
[10251.059808] [<ffffffff815163b7>] scsi_eh_bus_reset+0xf7/0x270
<snip>
The problem is the following call sequence (simplified):
1) usb_reset_device
2) usb_reset_and_verify_device
2) hub_port_init
3) hub_port_finish_reset
3) xhci_discover_or_reset_device
This frees xhci->devs[slot_id]->eps[ep_index].ring for all eps but 0
4) usb_get_device_descriptor
This fails
5) hub_port_init fails
6) usb_reset_and_verify_device fails, does not restore device config
7) uas_post_reset
8) xhci_alloc_streams
NULL deref on the free-ed ring
This commit fixes this by not allowing usb_alloc_streams to continue if
the device is not configured.
Note that we do allow usb_free_streams to continue after a (logical)
disconnect, as it is necessary to explicitly free the streams at the xhci
controller level.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver wasn't properly configuring the hardware for the current
termios settings under all conditions. Ensure that termios are
written to the device when the port is activated.
Signed-off-by: Jim Paris <jim@jtan.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add device-id entry for GW Instek AFG-2225, which has a byte swapped
bInterfaceSubClass (0x20).
Reported-by: Karl Palsson <karlp@tweak.net.au>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull ceph fixes from Sage Weil:
"There is a GFP flag fix from Mike Christie, an error code fix from
Jan, and fixes for two unnecessary allocations (kmalloc and workqueue)
from Ilya. All are well tested.
Ilya has one other fix on the way but it didn't get tested in time"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: eliminate unnecessary allocation in process_one_ticket()
rbd: Fix error recovery in rbd_obj_read_sync()
libceph: use memalloc flags for net IO
rbd: use a single workqueue for all devices
result is always zero when comes here.
Signed-off-by: Yao Dongdong <yaodongdong@huawei.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Pull m68k update from Geert Uytterhoeven.
Just wiring up the bpf system call.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Wire up bpf
A surprisingly small batch of fixes for -rc3. Suspiciously small, I'd say.
Anyway, most of this are a few defconfig updates. Some for omap to deal
with kernel binary size (moving ipv6 to module, etc). A larger one for
socfpga that refreshes with some churn, but also turns on a few options
that makes the newly-added board in my bootfarm usable for testing.
OMAP3 will also now warn when booted with legacy (non-DT) boot protocols,
hopefully encouraging those who still care about some of those platforms
to submit DT support and report bugs where needed. Nothing stops working
though, this is just to warn for future deprecation.
Beyond this, very few actual bugfixes. A PXA fix for DEBUG_LL boot hangs,
a missing terminting entry in a dt_match array on RealView a MTD fix on
OMAP with NAND.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=JasG
-----END PGP SIGNATURE-----
Merge tag 'armsoc-for-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A surprisingly small batch of fixes for -rc3. Suspiciously small, I'd
say.
Anyway, most of this are a few defconfig updates. Some for omap to
deal with kernel binary size (moving ipv6 to module, etc). A larger
one for socfpga that refreshes with some churn, but also turns on a
few options that makes the newly-added board in my bootfarm usable for
testing.
OMAP3 will also now warn when booted with legacy (non-DT) boot
protocols, hopefully encouraging those who still care about some of
those platforms to submit DT support and report bugs where needed.
Nothing stops working though, this is just to warn for future
deprecation.
Beyond this, very few actual bugfixes. A PXA fix for DEBUG_LL boot
hangs, a missing terminting entry in a dt_match array on RealView a
MTD fix on OMAP with NAND"
[ Obviously missed rc3, will make rc4 instead ;) ]
* tag 'armsoc-for-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: drop list entry for davinci
ARM: OMAP2+: Warn about deprecated legacy booting mode
ARM: omap2plus_defconfig: Fix errors with NAND BCH
ARM: multi_v7_defconfig: fix support for APQ8084
soc: versatile: Add terminating entry for realview_soc_of_match
ARM: ixp4xx: remove compilation warnings in io.h
MAINTAINERS: Add Soren as reviewer for Zynq
ARM: omap2plus_defconfig: Fix bloat caused by having ipv6 built-in
ARM: socfpga_defconfig: Update defconfig for SoCFPGA
ARM: pxa: fix hang on startup with DEBUG_LL
drivers/media/dvb-frontends/sp2.c:269:5: sparse: symbol 'sp2_init' was not declared. Should it be static?
drivers/media/dvb-frontends/sp2.c:351:5: sparse: symbol 'sp2_exit' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Running ftracetests on a box that mounted debugfs in two locations
made the ftracetests fail. This is because the tests uses a grep
of debugfs from the /proc/mounts file to find the debugfs mount
point, and then appends "/tracing" to that string to get the tracing
directory.
If the debugfs directory is mounted twice, then that grep will return
two answers and appending "/tracing" to a string with two lines will
not work.
Use "head -1" to only take the first mount point found.
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The default used to be that the first vivid device instance was
single planar, the second multi planar, the third single planar, etc.
However, that turned out to be unexpected and awkward. Change the
driver to always default to single planar.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The struct of_regulator_match rmatch[] is declared as a non-static local
variable so the structure members are not auto-initialized.
Initialize the array at declaration time to avoid the structure members
values to be indeterminate and have sane defaults instead.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The struct of_regulator_match rmatch[] is declared as a non-static local
variable so the structure members are not auto-initialized.
Initialize the array at declaration time to avoid the structure members
values to be indeterminate and have sane defaults instead.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The struct of_regulator_match is declared as a non-static local variable
so the structure members are not auto-initialized.
Initialize the struct at declaration time to avoid the structure members
values to be indeterminate and have sane defaults instead.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The struct of_regulator_match is declared as a non-static local variable
so the structure members are not auto-initialized.
Initialize the struct at declaration time to avoid the structure members
values to be indeterminate and have sane defaults instead.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The struct of_regulator_match rmatch[] is declared as a non-static local
variable so the structure members are not auto-initialized.
Initialize the array at declaration time to avoid the structure members
values to be indeterminate and have sane defaults instead.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver allocated on stack struct regulator_config but didn't initialize
it fully. Few fields (driver_data, ena_gpio) were left untouched. This
lead to using random ena_gpio values as GPIOs for max77693 regulators.
On occasion these values could match real GPIO numbers leading to
interfering with other drivers and to unsuccessful enable/disable of
regulator.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 80b022e29b ("regulator: max77693: Add max77693 regualtor driver.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
With kernel 3.17 the imon remote control for device 15c2:0034 does not
work anymore, which uses the OTHER protocol. Only the front panel
buttons which uses the RC6 protocol are working.
Adds the missing comparison for the RC_BIT_OTHER.
Cc: stable@vger.kernel.org # for Kernel 3.17
Signed-off-by: Ulrich Eckhardt <uli@uli-eckhardt.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change CONFIG_PM to CONFIG_PM_SLEEP to solve
warning: 'hix5hd2_ir_suspend' & 'hix5hd2_ir_resume' defined but not used
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Write may be called from interrupt context so make sure to use
GFP_ATOMIC for all allocations in write.
Fixes: 0d930e51cf ("USB: opticon: Add Opticon OPN2001 write support")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Write may be called from interrupt context so make sure to use
GFP_ATOMIC for all allocations in write.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
* Factor out code for clearing raised IRQs from exynos_tmu_work() to
exynos_tmu_clear_irqs().
* Add a comment about documentation bugs to exynos_tmu_clear_irqs().
[ The documentation for Exynos3250, Exynos4412, Exynos5250 and
Exynos5260 incorrectly states that INTCLEAR register has
a different placing of bits responsible for FALL IRQs than
INTSTAT register. Exynos5420 and Exynos5440 documentation is
correct (Exynos4210 doesn't support FALL IRQs at all). ]
* Use exynos_tmu_clear_irqs() in exynos_tmu_initialize() instead
of open-coded code trying to clear IRQs according to predefined
masks. After this change exynos_tmu_initialize() just clears
IRQs that are raised like it is already done in exynos_tmu_work().
As a nice side-effect the code now uses the correct offset
(16 instead of 12) for bits responsible for clearing FALL IRQs
in INTCLEAR register on Exynos3250, Exynos4412 and Exynos5250.
* Remove no longer needed intclr_rise_[mask,shift] and
intclr_fall_[mask,shift] fields from struct exynos_tmu_registers.
* Remove no longer needed defines.
This patch has been tested on Exynos4412 and Exynos5420 SoCs.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Here on function return all temporarily used device nodes shall
decrement their usage counter. The problems are found with device
nodes allocated by for_each_child_of_node(), of_parse_phandle()
and of_find_node_by_name(), fix all problems at once.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: devicetree@vger.kernel.org
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch add support for TRIM_RELOAD feature at Exynos3250. The TMu of
Exynos3250 has two TRIMINFO_CON register and must need to set RELOAD bit
before reading TRIMINFO register.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Reviewed-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch support many TRIMINFO_CTRL registers if specific Exynos SoC
has one more TRIMINFO_CTRL registers. Also this patch uses proper 'RELOAD'
shift/mask bit operation to set RELOAD feature instead of static value.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Reviewed-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Currently these SoCs claim TRIM_RELOAD support but don't have
triminfo_ctrl register address defined in their struct
exynos_tmu_registers entries. This causes incorrect write of
value "1" to data->base + 0x00 address (which happens to be
TRIMINFO register). Additionally according to the documentation
that I have neither Exynos5260 nor Exynos5420 support/require
TRIM_RELOAD feature. Thus fix the aforementioned issue by
removing TMU_SUPPORT_TRIM_RELOAD flag for both Exynos5260 and
Exynos5420.
Cc: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
There is no need for abstracting configuration for registers that
are identical on all SoC types.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
pdata->reference_voltage and pdata->gain are always defined
to non-zero values so remove the redundant checks from
exynos_tmu_control().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Cache number of non-hardware trigger levels in a new pdata field
(non_hw_trigger_levels) and convert code in exynos_tmu_initialize()
accordingly.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
* Remove dead temp check from temp_to_code() (this function users
in exynos_tmu_initialize() always pass correct temperatures and
exynos_tmu_set_emulation() returns early for EXYNOS4210 because
TMU_SUPPORT_EMULATION flag is not set on this SoC).
* Move temp_code check from code_to_temp() to exynos_tmu_read()
(code_to_temp() only user).
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Stefan Agner