This fix can probably wait 2.6.33, or should use another patch
if needed in 2.6.32 (no get_dev_by_index_rcu() before 2.6.33)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
move checking if eaction is valid in tcf_mirred_init()
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. don't let go back using goto.
2. don't call skb_act_clone() until it is necessary.
3. one exit of the critical context.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes in the TX error propagation require additional checking
and masking of values returned from hard_start_xmit(), mainly to
separate cases where skb was consumed. This aim can be simplified by
changing the order of NETDEV_TX and NET_XMIT codes, because the latter
are treated similarly to negative (ERRNO) values.
After this change much simpler dev_xmit_complete() is also used in
sch_direct_xmit(), so it is moved to netdevice.h.
Additionally NET_RX definitions in netdevice.h are moved up from
between TX codes to avoid confusion while reading the TX comment.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the ->ndo_hard_start_xmit() callbacks are only permitted to return
one of the NETDEV_TX codes. This prevents any kind of error propagation for
virtual devices, like queue congestion of the underlying device in case of
layered devices, or unreachability in case of tunnels.
This patches changes the NET_XMIT codes to avoid clashes with the NETDEV_TX
codes and changes the two callers of dev_hard_start_xmit() to expect either
errno codes, NET_XMIT codes or NETDEV_TX codes as return value.
In case of qdisc_restart(), all non NETDEV_TX codes are mapped to NETDEV_TX_OK
since no error propagation is possible when using qdiscs. In case of
dev_queue_xmit(), the error is propagated upwards.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use RCU to walk list of network devices in qdisc dump.
This could be optimized for large number of devices.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
something-bility is spelled as something-blity
so a grep for 'blit' would find these lines
this is so trivial that I didn't split it by subsystem / copy
additional maintainers - all changes are to comments
The only purpose is to get fewer false positives when grepping
around the kernel sources.
Signed-off-by: Dirk Hohndel <hohndel@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We hold RTNL in tc_dump_tfilter(), we can avoid dev_hold()/dev_put()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another rcu conversion to avoid one dev_hold()/dev_put() pair
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This probably deserves to go into -stable.
Pedit will reject a policy that is large because it
uses the wrong structure in the policy validation.
This fixes it.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9ef1d4c7c7 ("[NETLINK]: Missing
initializations in dumped data") introduced a typo in
initialization. This patch fixes this.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek Poplawski a écrit :
>
>
> Hmm... So you made me to do some "real" work here, and guess what?:
> there is one serious checkpatch warning! ;-) Plus, this new parameter
> should be added to the function description. Otherwise:
> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
>
> Thanks,
> Jarek P.
>
> PS: I guess full "Don't" would show we really mean it...
Okay :) Here is the last round, before the night !
Thanks again
[RFC] pkt_sched: gen_estimator: Don't report fake rate estimators
We currently send TCA_STATS_RATE_EST elements to netlink users, even if no estimator
is running.
# tc -s -d qdisc
qdisc pfifo_fast 0: dev eth0 root bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1
Sent 112833764978 bytes 1495081739 pkt (dropped 0, overlimits 0 requeues 0)
rate 0bit 0pps backlog 0b 0p requeues 0
User has no way to tell if the "rate 0bit 0pps" is a real estimation, or a fake
one (because no estimator is active)
After this patch, tc command output is :
$ tc -s -d qdisc
qdisc pfifo_fast 0: dev eth0 root bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1
Sent 561075 bytes 1196 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
We add a parameter to gnet_stats_copy_rate_est() function so that
it can use gen_estimator_active(bstats, r), as suggested by Jarek.
This parameter can be NULL if check is not necessary, (htb for
example has a mandatory rate estimator)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some classful qdiscs miss qstats.qlen updating with q.qlen of their
child qdiscs in dump_stats methods.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If qdisc_get_stab returns error in qdisc_create there is skipped qdisc
ops->destroy, which is necessary because it's after ops->init at the
moment, so memory leaks are quite probable.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the recent mq change there is the new select_queue qdisc class
method used in tc_modify_qdisc, but it works OK only for direct child
qdiscs of mq qdisc. Grandchildren always get the first tx queue, which
would give wrong qdisc_root etc. results (e.g. for sch_htb as child of
sch_prio). This patch fixes it by using parent's dev_queue for such
grandchildren qdiscs. The select_queue method's return type is changed
BTW.
With feedback from: Patrick McHardy <kaber@trash.net>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the recent mq change using ingress qdisc overwrites dev->qdisc;
there is also a wrong old qdisc pointer passed to notify_and_destroy.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1623 commits)
netxen: update copyright
netxen: fix tx timeout recovery
netxen: fix file firmware leak
netxen: improve pci memory access
netxen: change firmware write size
tg3: Fix return ring size breakage
netxen: build fix for INET=n
cdc-phonet: autoconfigure Phonet address
Phonet: back-end for autoconfigured addresses
Phonet: fix netlink address dump error handling
ipv6: Add IFA_F_DADFAILED flag
net: Add DEVTYPE support for Ethernet based devices
mv643xx_eth.c: remove unused txq_set_wrr()
ucc_geth: Fix hangs after switching from full to half duplex
ucc_geth: Rearrange some code to avoid forward declarations
phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYs
drivers/net/phy: introduce missing kfree
drivers/net/wan: introduce missing kfree
net: force bridge module(s) to be GPL
Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded
...
Fixed up trivial conflicts:
- arch/x86/include/asm/socket.h
converted to <asm-generic/socket.h> in the x86 tree. The generic
header has the same new #define's, so that works out fine.
- drivers/net/tun.c
fix conflict between 89f56d1e9 ("tun: reuse struct sock fields") that
switched over to using 'tun->socket.sk' instead of the redundantly
available (and thus removed) 'tun->sk', and 2b980dbd ("lsm: Add hooks
to the TUN driver") which added a new 'tun->sk' use.
Noted in 'next' by Stephen Rothwell.
When new child qdiscs are attached to the mq qdisc, they are actually
attached as root qdiscs to the device queues. The lock selection for
new estimators incorrectly picks the root lock of the existing and
to be replaced qdisc, which results in a use-after-free once the old
qdisc has been destroyed.
Mark mq qdisc instances with a new flag and treat qdiscs attached to
mq as children similar to regular root qdiscs.
Additionally prevent estimators from being attached to the mq qdisc
itself since it only updates its byte and packet counters during dumps.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a classful dummy scheduler which can be used as root qdisc
for multiqueue devices and exposes each device queue as a child class.
This allows to address queues individually and graft them similar to regular
classes. Additionally it presents an accumulated view of the statistics of
all real root qdiscs in the dummy root.
Two new callbacks are added to the qdisc_ops and qdisc_class_ops:
- cl_ops->select_queue selects the tx queue number for new child classes.
- qdisc_ops->attach() overrides root qdisc device grafting to attach
non-shared qdiscs to the queues.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
It will be used in a following patch by the multiqueue qdisc.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the multiqueue integration with the qdisc API suffers from
a few problems:
- with multiple queues, all root qdiscs use the same handle. This means
they can't be exposed to userspace in a backwards compatible fashion.
- all API operations always refer to queue number 0. Newly created
qdiscs are automatically shared between all queues, its not possible
to address individual queues or restore multiqueue behaviour once a
shared qdisc has been attached.
- Dumps only contain the root qdisc of queue 0, in case of non-shared
qdiscs this means the statistics are incomplete.
This patch reintroduces dev->qdisc, which points to the (single) root qdisc
from userspace's point of view. Currently it either points to the first
(non-shared) default qdisc, or a qdisc shared between all queues. The
following patches will introduce a classful dummy qdisc, which will be used
as root qdisc and contain the per-queue qdiscs as children.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The class argument to the ->graft(), ->leaf(), ->dump(), ->dump_stats() all
originate from either ->get() or ->walk() and are always valid.
Remove unnecessary checks.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some schedulers don't support creating, changing or deleting classes.
Make the respective callbacks optionally and consistently return
-EOPNOTSUPP for unsupported operations, instead of currently either
-EOPNOTSUPP, -ENOSYS or no error.
In case of sch_prio and sch_multiq, the removed operations additionally
checked for an invalid class. This is not necessary since the class
argument can only orginate from ->get() or in case of ->change is 0
for creation of new classes, in which case ->change() incorrectly
returned -ENOENT.
As a side-effect, this patch fixes a possible (root-only) NULL pointer
function call in sch_ingress, which didn't implement a so far mandatory
->delete() operation.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some qdiscs don't support attaching filters. Handle this centrally in
cls_api and return a proper errno code (EOPNOTSUPP) instead of EINVAL.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the parent qdisc doesn't support classes, use EOPNOTSUPP.
If the parent class doesn't exist, use ENOENT. Currently EINVAL
is returned in both cases.
Additionally check whether grafting is supported and remove a now
unnecessary graft function from sch_ingress.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three bytes of uninitialized kernel memory are currently leaked to user
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are full of unresolved problems, mainly that conversions don't
work 1-1 from hrtimers to tasklet_hrtimers because unlike hrtimers
tasklets can't be killed from softirq context.
And when a qdisc gets reset, that's exactly what we need to do here.
We'll work this out in the net-next-2.6 tree and if warranted we'll
backport that work to -stable.
This reverts the following 3 changesets:
a2cb6a4dd4
("pkt_sched: Fix bogon in tasklet_hrtimer changes.")
38acce2d79
("pkt_sched: Convert CBQ to tasklet_hrtimer.")
ee5f9757ea
("pkt_sched: Convert qdisc_watchdog to tasklet_hrtimer")
Signed-off-by: David S. Miller <davem@davemloft.net>
pfifo_fast_enqueue has this check:
if (skb_queue_len(list) < qdisc_dev(qdisc)->tx_queue_len) {
which allows each band to enqueue upto tx_queue_len skbs for a
total of 3*tx_queue_len skbs. I am not sure if this was the
intention of limiting in qdisc.
Patch compiled and 32 simultaneous netperf testing ran fine. Also:
# tc -s qdisc show dev eth2
qdisc pfifo_fast 0: root bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1
Sent 16835026752 bytes 373116 pkt (dropped 0, overlimits 0 requeues 25)
rate 0bit 0pps backlog 0b 0p requeues 25
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maintain a per-qdisc bitmap for pfifo_fast giving availability
of skbs for each band. This allows faster lookup for a skb when
there are no high priority skbs. Also, it helps in (rare) cases
when there are no skbs on the list, where an immediate lookup is
faster than iterating through the three bands.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consitfy nlmsghdr arguments to a couple of functions as preparation
for the next patch, which will constify the netlink message data in
all nfnetlink users.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Reported by Stephen Rothwell, luckily it's harmless:
net/sched/sch_api.c: In function 'qdisc_watchdog':
net/sched/sch_api.c:460: warning: initialization from incompatible pointer type
net/sched/sch_cbq.c: In function 'cbq_undelay':
net/sched/sch_cbq.c:595: warning: initialization from incompatible pointer type
Signed-off-by: David S. Miller <davem@davemloft.net>
This code expects to run in softirq context, and bare hrtimers
run in hw IRQ context.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
None of this stuff should execute in hw IRQ context, therefore
use a tasklet_hrtimer so that it runs in softirq context.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
In 5e140dfc1f "net: reorder struct Qdisc
for better SMP performance" the definition of struct gnet_stats_basic
changed incompatibly, as copies of this struct are shipped to
userland via netlink.
Restoring old behavior is not welcome, for performance reason.
Fix is to use a private structure for kernel, and
teach gnet_stats_copy_basic() to convert from kernel to user land,
using legacy structure (struct gnet_stats_basic)
Based on a report and initial patch from Michael Spang.
Reported-by: Michael Spang <mspang@csclub.uwaterloo.ca>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_queue_xmit enqueue's a skb and calls qdisc_run which
dequeue's the skb and xmits it. In most cases, the skb that
is enqueue'd is the same one that is dequeue'd (unless the
queue gets stopped or multiple cpu's write to the same queue
and ends in a race with qdisc_run). For default qdiscs, we
can remove the redundant enqueue/dequeue and simply xmit the
skb since the default qdisc is work-conserving.
The patch uses a new flag - TCQ_F_CAN_BYPASS to identify the
default fast queue. The controversial part of the patch is
incrementing qlen when a skb is requeued - this is to avoid
checks like the second line below:
+ } else if ((q->flags & TCQ_F_CAN_BYPASS) && !qdisc_qlen(q) &&
>> !q->gso_skb &&
+ !test_and_set_bit(__QDISC_STATE_RUNNING, &q->state)) {
Results of a 2 hour testing for multiple netperf sessions (1,
2, 4, 8, 12 sessions on a 4 cpu system-X). The BW numbers are
aggregate Mb/s across iterations tested with this version on
System-X boxes with Chelsio 10gbps cards:
----------------------------------
Size | ORG BW NEW BW |
----------------------------------
128K | 156964 159381 |
256K | 158650 162042 |
----------------------------------
Changes from ver1:
1. Move sch_direct_xmit declaration from sch_generic.h to
pkt_sched.h
2. Update qdisc basic statistics for direct xmit path.
3. Set qlen to zero in qdisc_reset.
4. Changed some function names to more meaningful ones.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is the result of an automatic spatch transformation to convert
all ndo_start_xmit() return values of 0 to NETDEV_TX_OK.
Some occurences are missed by the automatic conversion, those will be
handled in a seperate patch.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 2b85a34e91
(net: No more expensive sock_hold()/sock_put() on each tx)
changed initial sk_wmem_alloc value.
We need to take into account this offset when reporting
sk_wmem_alloc to user, in PROC_FS files or various
ioctls (SIOCOUTQ/TIOCOUTQ)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Action police statistics could be misleading because drops are not
shown when expected.
With feedback from: Jamal Hadi Salim <hadi@cyberus.ca>
Reported-by: Pawel Staszewski <pstaszewski@itcare.pl>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's use TICKS instead of US, so PSCHED_TICKS2NS and PSCHED_NS2TICKS
(like in PSCHED_TICKS_PER_SEC already) to avoid misleading.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert magic values 1 and -1 to NETDEV_TX_BUSY and NETDEV_TX_LOCKED respectively.
0 (NETDEV_TX_OK) is not changed to keep the noise down, except in very few cases
where its in direct proximity to one of the other values.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use PSCHED_SHIFT constant instead of '10' in PSCHED_US2NS() and
PSCHED_NS2US() macros to enable changing this value later.
Additionally use PSCHED_SHIFT in sch_hfsc SM_SHIFT and ISM_SHIFT
definitions. This part of the patch is based on feedback from
Patrick McHardy <kaber@trash.net>.
Reported-by: Antonio Almeida <vexwek@gmail.com>
Tested-by: Antonio Almeida <vexwek@gmail.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I found a bug in cls_cgroup_change() in cls_cgroup.c.
cls_cgroup_change() expected tca[TCA_OPTIONS] was set from user space properly,
but tc in iproute2-2.6.29-1 (which I used) didn't set it.
In the current source code of tc in git, it set tca[TCA_OPTIONS].
git://git.kernel.org/pub/scm/linux/kernel/git/shemminger/iproute2.git
If we always use a newest iproute2 in git when we use cls_cgroup,
we don't face this oops probably.
But I think, kernel shouldn't panic regardless of use program's behaviour.
Signed-off-by: Minoru Usui <usui@mxm.nes.nec.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define three accessors to get/set dst attached to a skb
struct dst_entry *skb_dst(const struct sk_buff *skb)
void skb_dst_set(struct sk_buff *skb, struct dst_entry *dst)
void skb_dst_drop(struct sk_buff *skb)
This one should replace occurrences of :
dst_release(skb->dst)
skb->dst = NULL;
Delete skb->dst field
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define skb_rtable(const struct sk_buff *skb) accessor to get rtable from skb
Delete skb->rtable field
Setting rtable is not allowed, just set dst instead as rtable is an alias.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug which unconfigured struct tcf_proto keeps
chaining in tc_ctl_tfilter(), and avoids kernel panic in
cls_cgroup_classify() when we use cls_cgroup.
When we execute 'tc filter add', tcf_proto is allocated, initialized
by classifier's init(), and chained. After it's chained,
tc_ctl_tfilter() calls classifier's change(). When classifier's
change() fails, tc_ctl_tfilter() does not free and keeps tcf_proto.
In addition, cls_cgroup is initialized in change() not in init(). It
accesses unconfigured struct tcf_proto which is chained before
change(), then hits Oops.
Signed-off-by: Minoru Usui <usui@mxm.nes.nec.co.jp>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Tested-by: Minoru Usui <usui@mxm.nes.nec.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid reading the unsynchronized value cs->classid multiple times,
since it could change concurrently from non-zero to zero; this would
result in the classifier returning a positive result with a bogus
(zero) classid.
Signed-off-by: Paul Menage <menage@google.com>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We would like to get rid of netdev->trans_start = jiffies; that about all net
drivers have to use in their start_xmit() function, and use txq->trans_start
instead.
This can be done generically in core network, as suggested by David.
Some devices, (particularly loopback) dont need trans_start update, because
they dont have transmit watchdog. We could add a new device flag, or rely
on fact that txq->tran_start can be updated is txq->xmit_lock_owner is
different than -1. Use a helper function to hide our choice.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can slightly reduce size of teqlN structure, not duplicating stats
structure in teql_master but using stats field from net_device.stats
for tx_errors and from netdev_queue for tx_bytes/tx_packets/tx_dropped
values.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is illegal to dereference a skb after a successful ndo_start_xmit()
call. We must store skb length in a local variable instead.
Bug was introduced in 2.6.27 by commit 0abf77e55a
(net_sched: Add accessor function for packet length for qdiscs)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct net_device trans_start field is a hot spot on SMP and high performance
devices, particularly multi queues ones, because every transmitter dirties
it. Is main use is tx watchdog and bonding alive checks.
But as most devices dont use NETIF_F_LLTX, we have to lock
a netdev_queue before calling their ndo_start_xmit(). So it makes
sense to move trans_start from net_device to netdev_queue. Its update
will occur on a already present (and in exclusive state) cache line, for
free.
We can do this transition smoothly. An old driver continue to
update dev->trans_start, while an updated one updates txq->trans_start.
Further patches could also put tx_bytes/tx_packets counters in
netdev_queue to avoid dirtying dev->stats (vlan device comes to mind)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can remove this lock here, since we are in cgroup write handler and
thus the cgrp is guaranteed to be valid, and no lock is needed when
writing a u32 variable.
Signed-off-by: Li Zefan <lizf@cn.fujitsuc.com>
Acked-by: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When no limit is given, the bfifo uses a default of tx_queue_len * mtu.
Packets handled by qdiscs include the link layer header, so this should
be taken into account, similar to what other qdiscs do.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel should only be using the high 16 bits of a kernel
generated priority. Filter priorities in all other cases only
use the upper 16 bits of the u32 'prio' field of 'struct tcf_proto',
but when the kernel generates the priority of a filter is saves all
32 bits which can result in incorrect lookup failures when a filter
needs to be deleted or modified.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Sidorenko reported:
"while experimenting with 'netem' we have found some strange behaviour. It
seemed that ingress delay as measured by 'ping' command shows up on some
hosts but not on others.
After some investigation I have found that the problem is that skbuff->tstamp
field value depends on whether there are any packet sniffers enabled. That
is:
- if any ptype_all handler is registered, the tstamp field is as expected
- if there are no ptype_all handlers, the tstamp field does not show the delay"
This patch prevents unnecessary update of tstamp in dev_queue_xmit_nit()
on ingress path (with act_mirred) adding a check, so minimal overhead on
the fast path, but only when sniffers etc. are active.
Since netem at ingress seems to logically emulate a network before a host,
tstamp is zeroed to trigger the update and pretend delays are from the
outside.
Reported-by: Alex Sidorenko <alexandre.sidorenko@hp.com>
Tested-by: Alex Sidorenko <alexandre.sidorenko@hp.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When vlan acceleration is used on receive, the vlan tag is maintained
outside of the skb data. The existing vlan tag match only works on TX
path because it uses vlan_get_tag which tests for VLAN_HW_TX_ACCEL.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_sack_swap seems unnecessary so I pushed swap to the caller.
Also removed comment that seemed then pointless, and added include
when not already there. Compile tested.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
While looking for a possible reason of bugzilla report on HTB oops:
http://bugzilla.kernel.org/show_bug.cgi?id=12858
I found the code in htb_delete calling htb_destroy_class on zero
refcount is very misleading: it can suggest this is a common path, and
destroy is called under sch_tree_lock. Actually, this can never happen
like this because before deletion cops->get() is done, and after
delete a class is still used by tclass_notify. The class destroy is
always called from cops->put(), so without sch_tree_lock.
This doesn't mean much now (since 2.6.27) because all vulnerable calls
were moved from htb_destroy_class to htb_delete, but there was a bug
in older kernels. The same change is done for other classful scheds,
which, it seems, didn't have similar locking problems here.
Reported-by: m0sia <m0sia@m0sia.ru>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A commit c1b56878fb "tc: policing requires
a rate estimator" introduced a test which invalidates previously working
configs, based on examples from iproute2: doc/actions/actions-general.
This is too rigorous: a rate estimator is needed only when police's
"avrate" option is used.
Reported-by: Joao Correia <joaomiguelcorreia@gmail.com>
Diagnosed-by: John Dykstra <john.dykstra1@gmail.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drr_change_class lacks a check for NULL of tca[TCA_OPTIONS], so oops
is possible.
Reported-by: Denys Fedoryschenko <denys@visp.net.lb>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current "RTNETLINK answers: Invalid argument" warning, while trying to
add multiq qdisc to non-multiqueue device, isn't very helpful and some
of these devs can be changed btw., so let's use a better errno.
With feedback from Stephen Hemminger <shemminger@vyatta.com>
Reported-by: Badalian Vyacheslav <slavon@bigtelecom.ru>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy <kaber@trash.net> suggested using a workqueue instead
of hrtimers to trigger netif_schedule() when there is a problem with
setting exact time of this event: 'The differnce - yeah, it shouldn't
make much, mainly wake up the qdisc earlier (but not too early) after
"too many events" occured _and_ no further enqueue events wake up the
qdisc anyways.'
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's get some info on possible config problems. This patch brings
back an old warning, but is printed only once now.
With feedback from Patrick McHardy <kaber@trash.net>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy <kaber@trash.net> suggested:
> How about making this flag and the warning message (in a out-of-line
> function) globally available? Other qdiscs (f.i. HFSC) can't deal with
> inner non-work-conserving qdiscs as well.
This patch uses qdisc->flags field of "suspected" child qdisc.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently htb_do_events() breaks events recounting for a level after 2
jiffies, but there is no reason to repeat this for next levels and
increase delays even more (with softirqs disabled). htb_dequeue_tree()
can add to this too, btw. In such a case q->now time is invalid anyway.
Thanks to Patrick McHardy for spotting an error around earlier version
of this patch.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Next event time should consider jiffies used for recounting. Otherwise
qdisc_watchdog_schedule() triggers hrtimer immediately with the event
in the past, and may cause very high ksoftirqd cpu usage (if highres
is on).
There is also removed checking "event" for zero in htb_dequeue(): it's
always true in this place.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (84 commits)
wimax: fix kernel-doc for debufs_dentry member of struct wimax_dev
net: convert pegasus driver to net_device_ops
bnx2x: Prevent eeprom set when driver is down
net: switch kaweth driver to netdevops
pcnet32: round off carrier watch timer
i2400m/usb: wrap USB power saving in #ifdef CONFIG_PM
wimax: testing for rfkill support should also test for CONFIG_RFKILL_MODULE
wimax: fix kconfig interactions with rfkill and input layers
wimax: fix '#ifndef CONFIG_BUG' layout to avoid warning
r6040: bump release number to 0.20
r6040: warn about MAC address being unset
r6040: check PHY status when bringing interface up
r6040: make printks consistent with DRV_NAME
gianfar: Fixup use of BUS_ID_SIZE
mlx4_en: Returning real Max in get_ringparam
mlx4_en: Consider inline packets on completion
netdev: bfin_mac: enable bfin_mac net dev driver for BF51x
qeth: convert to net_device_ops
vlan: add neigh_setup
dm9601: warn on invalid mac address
...
New nodes are inserted in u32_change() under rtnl_lock() with wmb(),
so without tcf_tree_lock() like in other classifiers (e.g. cls_fw).
This isn't enough without rmb() on the read side, but on the other
hand adding such barriers doesn't give any savings, so the lock is
added instead.
Reported-by: m0sia <m0sia@plotinka.ru>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 22604c8668.
We can't fix this issue in this way, because we now can try
to take the dev_base_lock rwlock as a writer in software interrupt
context and that is not allowed without major surgery elsewhere.
This initial link state problem needs to be solved in some other
way.
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Michael Marineau <mike@marineau.org>
Commit b47300168e "Do not fire linkwatch
events until the device is registered." was made as a workaround for
drivers that call netif_carrier_off before registering the device.
Unfortunately this causes these drivers to incorrectly report their
link status as IF_OPER_UNKNOWN which can falsely set the IFF_RUNNING
flag when the interface is first brought up. This issues was
previously pointed out[1] but was dismissed saying that IFF_RUNNING is
not related to the link status. From my digging IFF_RUNNING, as
reported to userspace, is based on the link state. It is set based on
__LINK_STATE_START and IF_OPER_UP or IF_OPER_UNKNOWN. See [2], [3],
and [4]. (Whether or not the kernel has IFF_RUNNING set in flags is
not reported to user space so it may well be independent of the link,
I don't know if and when it may get set.)
The end result depends slightly depending on the driver. The the two I
tested were e1000e and b44. With e1000e if the system is booted
without a network cable attached the interface will falsely report
RUNNING when it is brought up causing NetworkManager to attempt to
start it and eventually time out. With b44 when the system is booted
with a network cable attached and brought up with dhcpcd it will time
out the first time.
The attached patch that will still set the operstate variable
correctly to IF_OPER_UP/DOWN/etc when linkwatch_fire_event is called
but then return rather than skipping the linkwatch_fire_event call
entirely as the previous fix did. (sorry it isn't inline, I don't have
a patch friendly email client at the moment)
Signed-off-by: David S. Miller <davem@davemloft.net>
cls_cgroup can't be compiled as a module, since it's not supported by
cgroup.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- It's better to use container_of() instead of casting cgroup_subsys_state *
to cgroup_cls_state *.
- Add helper function task_cls_state().
- Rename net_cls_state() to cgrp_cls_state().
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing a cgroup, an oops was triggered immediately. The cause
is wrong kfree() in cgrp_destroy().
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
net: Allow dependancies of FDDI & Tokenring to be modular.
igb: Fix build warning when DCA is disabled.
net: Fix warning fallout from recent NAPI interface changes.
gro: Fix potential use after free
sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
sfc: When disabling the NIC, close the device rather than unregistering it
sfc: SFT9001: Add cable diagnostics
sfc: Add support for multiple PHY self-tests
sfc: Merge top-level functions for self-tests
sfc: Clean up PHY mode management in loopback self-test
sfc: Fix unreliable link detection in some loopback modes
sfc: Generate unique names for per-NIC workqueues
802.3ad: use standard ethhdr instead of ad_header
802.3ad: generalize out mac address initializer
802.3ad: initialize ports LACPDU from const initializer
802.3ad: remove typedef around ad_system
802.3ad: turn ports is_individual into a bool
802.3ad: turn ports is_enabled into a bool
802.3ad: make ntt bool
ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
...
Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).
While implementing a TCQ_F_THROTTLED flag there was used an smp_wmb()
in qdisc_watchdog(), but since this flag is practically used only in
sch_netem(), and since it's not even clear what reordering is avoided
here (TCQ_F_THROTTLED vs. __QDISC_STATE_SCHED?) it seems the barrier
could be safely removed.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some gcc versions warn that ret may be used uninitialized in
sfq_enqueue(). It's a false positive, so let's annotate this.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netem simulator is no longer limited by Linux timer resolution HZ.
Not since Patrick McHardy changed the QoS system to use hrtimer.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can skip WARN_ON() in htb_dequeue_tree() because there should be
always a similar warning from htb_lookup_leaf() earlier.
The first WARN_ON() in in htb_lookup_leaf() is changed to BUG_ON()
because most likly this should end with oops anyway.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
htb_id_find_next_upper() is usually called to find a class with next
id after some previously removed class, so let's move a check for
equality to the end: it's the least likely here.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
fs/nfsd/nfs4recover.c
Manually fixed above to use new creds API functions, e.g.
nfs4_save_creds().
Signed-off-by: James Morris <jmorris@namei.org>
Replace HTB_ACCNT() macro with inlines to make it more readable.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
L2T() is currently used only in one place (and has one spurious
parameter, btw), so let's: 'get rid of L2T completely, and just
use "qdisc_l2t(rate, size)" directly.' - quote & feedback from
David S. Miller.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While implementing htb_parent_to_leaf() there where added backup prio
and quantum struct htb_class fields to preserve these values for inner
classes in case of their return to leaf. This patch cleans this a bit
by removing union leaf duplicates.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: make global function static
Fix the following sparse warning:
net/sched/sch_api.c:192:14: warning: symbol 'qdisc_match_from_root' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since all other gen_estimator functions use bstats and rate_est params
together, and searching for them is optimized now, let's use this also
in gen_estimator_active(). The return type of gen_estimator_active()
is changed to bool, and gen_find_node() parameters to const, btw.
In tcf_act_police_locate() a check for ACT_P_CREATED is added before
calling gen_estimator_active().
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Found that while trying average rate policing, it was possible to
request average rate policing without a rate estimator. This results
in no policing which is harmless but incorrect.
Since policing could be setup in two steps, need to check
in the kernel.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions gen_new_estimator and gen_replace_estimator can return
errors, but they were being ignored.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow tcf_hash_create to return different errors on estimator failure.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this warning:
net/sched/sch_hfsc.c: In function ‘hfsc_enqueue’:
net/sched/sch_hfsc.c:1577: warning: ‘err’ may be used uninitialized in this function
triggers because GCC does not recognize the (correct) error flow
between hfsc_classify(), 'cl' and 'err'.
Annotate it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
After implementing qdisc->ops->peek() there is no more calling
qdisc_tree_decrease_qlen() without rtnl_lock(), so qdisc_list_lock
added by commit: f6e0b239a2 "pkt_sched:
Fix qdisc list locking" can be removed.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek Poplawski points out:
If all child qdiscs of sch_drr are non-work-conserving (e.g. sch_tbf)
drr_dequeue() will busy-loop waiting for skbs instead of leaving the
job for a watchdog. Checking for list_empty() in each loop isn't
necessary either, because this can never be true except the first time.
Using non-work-conserving qdiscs as children of DRR makes no sense,
simply bail out in that case.
Reported-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of xchg() hasn't been necessary since 2.2.something when proper
locking was added to packet schedulers. In the case of classifiers they
mostly weren't even necessary before that since they're mainly used
to assign a NULL pointer to the filter root in the ->destroy path;
the root is destroyed immediately after that.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of xchg() hasn't been necessary since 2.2.something when proper
locking was added to packet schedulers.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add classful DRR scheduler as a more flexible replacement for SFQ.
The main difference to the algorithm described in "Efficient Fair Queueing
using Deficit Round Robin" is that this implementation doesn't drop packets
from the longest queue on overrun because its classful and limits are
handled by each individual child qdisc.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
nla_nest_start() might return NULL, causing a NULL pointer dereference.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the network device internal API to move adminstrative
operations out of the network device structure and into a separate structure.
This patch involves some hackery to maintain compatablity between the
new and old model, so all 300+ drivers don't have to be changed at once.
For drivers that aren't converted yet, the netdevice_ops virt function list
still resides in the net_device structure. For old protocols, the new
net_device_ops are copied out to the old net_device pointers.
After the transistion is completed the nag message can be changed to
an WARN_ON, and the compatiablity code can be made configurable.
Some function pointers aren't moved:
* destructor can't be in net_device_ops because
it may need to be referenced after the module is unloaded.
* neighbor setup is manipulated in a couple of places that need special
consideration
* hard_start_xmit is in the fast path for transmit.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several device drivers try to do things like netif_carrier_off()
before register_netdev() is invoked. This is bogus, but too many
drivers do this to fix them all up in one go.
Reported-by: Folkert van Heusden <folkert@vanheusden.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simply delete ops from list and let list debugging do the job.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After implementing qdisc->ops->peek() and changing sch_netem into
classless qdisc there are no more qdisc->ops->requeue() users. This
patch removes this method with its wrappers (qdisc_requeue()), and
also unused qdisc->requeue structure. There are a few minor fixes of
warnings (htb_enqueue()) and comments btw.
The idea to kill ->requeue() and a similar patch were first developed
by David S. Miller.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attach creds to file structs and discard f_uid/f_gid.
file_operations::open() methods (such as hppfs_open()) should use file->f_cred
rather than current_cred(). At the moment file->f_cred will be current_cred()
at this point.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <jmorris@namei.org>
Signed-off-by: James Morris <jmorris@namei.org>
The classifier should cover the most common use case and will work
without any special configuration.
The principle of the classifier is to directly access the
task_struct via get_current(). In order for this to work,
classification requests from softirqs must be ignored. This is
not a problem because the vast majority of packets in softirq
context are not assigned to a task anyway. For this to work, a
mechanism is needed to trace softirq context.
This repost goes back to the method of relying on the number of
nested bh disable calls for the sake of not adding too much
complexity and the option to come up with something more reliable
if actually needed.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All these individual parsing functions never return an error,
so they can be void.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since gso_skb is re-used for qdisc_peek_dequeued(), and this skb is
counted in the qdisc->q.qlen, it has to be kfreed during qdisc_reset()
when qlen is zeroed.
With help from David S. Miller <davem@davemloft.net>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After removing netem classful functionality we are sure its inner
qdisc is tfifo, so we can replace qdisc->ops->requeue() method with
open code. After this patch there are no more ops->requeue() users.
The idea of this patch is by Patrick McHardy.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy noticed that: "a lot of the functionality of netem
requires the inner tfifo anyways and rate-limiting is usually done
on top of netem. So I would suggest so either hard-wire the tfifo
qdisc or at least make the assumption that inner qdiscs are
work-conserving.", and later: "- a lot of other qdiscs still don't
work as inner qdiscs of netem [...]".
So, according to his suggestion, this patch removes classful options
of netem. The main reason of this change is to remove ops->requeue()
method, which is currently used only by netem.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds qdisc_peek_dequeued() wrapper to emulate peek method
with qdisc->dequeue() and storing "peeked" skb in qdisc->gso_skb until
dequeuing. This is mainly for compatibility reasons not to break some
strange configs because peeking is expected for non-work-conserving
parent qdiscs to query work-conserving child qdiscs.
This implementation requires using qdisc_dequeue_peeked() wrapper
instead of directly calling qdisc->dequeue() for all qdiscs ever
querried with qdisc->ops->peek() or qdisc_peek_dequeued().
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use qdisc->ops->peek() instead of ->dequeue() & ->requeue() pair.
After this patch the only remaining user of qdisc->ops->requeue() is
netem_enqueue(). Based on ideas of Herbert Xu, Patrick McHardy and
David S. Miller.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add qdisc->ops->peek() implementation for work-conserving qdiscs.
With feedback from Patrick McHardy.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Patrick McHardy <kaber@trash.net>
Just as a demonstration how easy adding a peek operation to the
work-conserving qdiscs actually is. It doesn't need to keep or change
any internal state in many cases thanks to the guarantee that the
packet will either be dequeued or, if another packet arrives, the
upper qdisc will immediately ->peek again to reevaluate the state.
(This is only slightly modified Patrick's patch.)
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After these commands:
# modprobe sch_teql
# tc qdisc add dev eth0 root teql0
# tc qdisc del dev eth0 root
we get an oops in teql_destroy() when spin_lock is taken from a null
qdisc_sleeping pointer. It's because at the moment teql0 dev haven't
been activated yet, and a qdisc_root_sleeping() is pointing to noop
qdisc's netdev_queue with qdisc_sleeping uninitialized. This patch
fixes this both for noop and noqueue netdev_queues to avoid similar
problems in the future.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some code here depends on CONFIG_KMOD to not try to load
protocol modules or similar, replace by CONFIG_MODULES
where more than just request_module depends on CONFIG_KMOD
and and also use try_then_request_module in ebtables.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the last change of requeuing there is no info about such
incidents in tc stats. This patch updates the counter, but we should
consider this should differ from previous stats because of additional
checks preventing to repeat this. On the other hand, previous stats
didn't include requeuing of gso_segmented skbs.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By passing in the family through which extensions were invoked, a bit
of data space can be reclaimed. The "family" member will be added to
the parameter structures and the check functions be adjusted.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch does this for target extensions' destroy functions.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch does this for target extensions' checkentry functions.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch does this for target extensions' target functions.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
It used to be that {ip,ip6,etc}_tables called extension->checkentry
themselves, but this can be moved into the xtables core.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
qdisc->requeue was planned to universally replace all requeuing code,
but at the top level we never requeue more than one skb, so qdisc->
gso_skb is enough for this. qdisc->requeue would be used on the lower
levels only for one level deep requeuing (like in sch_hfsc) after
finishing all the changes.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jay Cliburn noticed and diagnosed a bug triggered in
dev_gso_skb_destructor() after last change from qdisc->gso_skb
to qdisc->requeue list. Since gso_segmented skbs can't be queued
to another list this patch brings back qdisc->gso_skb for them.
Reported-by: Jay Cliburn <jcliburn@gmail.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check in dequeue_skb() the state of tx_queue for requeued skb to save
on locking and re-requeuing, and possibly remove the current check in
qdisc_run(). Based on the idea of Alexander Duyck.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason to call into the complicated qdiscs
just to remember the last SKB where we found the device
blocked.
The SKB is outside of the qdiscs realm at this point.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently dequeueing a packet and requeueing the same packet will cause a
different packet to be pulled on the next dequeue. This change forces
requeue to rewind the current_band.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resolves a few issues found with multiq including wording
suggestions and a problem seen in the allocation of queues.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new action will have the ability to change the priority and/or
queue_mapping fields on an sk_buff.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is intended to add a qdisc to support the new tx multiqueue
architecture by providing a band for each hardware queue. By doing
this it is possible to support a different qdisc per physical hardware
queue.
This qdisc uses the skb->queue_mapping to select which band to place
the traffic onto. It then uses a round robin w/ a check to see if the
subqueue is stopped to determine which band to dequeue the packet from.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch turns the netdev timeout WARN_ON_ONCE() into a WARN_ONCE(),
so that the device and driver names are inside the warning message.
This helps automated tools like kerneloops.org to collect the data
and do statistics, as well as making it more likely that humans
cut-n-paste the important message as part of a bugreport.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to be able to do range hrtimers we need to use accessor functions
to the "expire" member of the hrtimer struct.
This patch converts sched_cbq to these accessors.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Removes all _nested_compat() functions from the API. The prio qdisc
no longer requires them and netem has its own format anyway. Their
existance is only confusing.
Resend: Also remove the wrapper macro.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use qdisc_root_sleeping_lock() instead of qdisc_root_lock() where
appropriate. The only difference is while dev is deactivated, when
currently we can use a sleeping qdisc with the lock of noop_qdisc.
This shouldn't be dangerous since after deactivation root lock could
be used only by gen_estimator code, but looks wrong anyway.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While passing a qdisc root lock to gen_new_estimator() and
gen_replace_estimator() dev could be deactivated or even before
grafting proper root qdisc as qdisc_sleeping (e.g. qdisc_create), so
using qdisc_root_lock() is not enough. This patch adds
qdisc_root_sleeping_lock() for this, plus additional checks, where
necessary.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pointers are RCU protected, so proper primitives should be used.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During dev_graft_qdisc() dev is deactivated, so qdisc_root_lock()
returns wrong lock of noop_qdisc instead of qdisc_sleeping.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since some qdiscs call qdisc_tree_decrease_qlen() (so qdisc_lookup())
without rtnl_lock(), adding and deleting from a qdisc list needs
additional locking. This patch adds global spinlock qdisc_list_lock
and wrapper functions for modifying the list. It is considered as a
temporary solution until hfsc_dequeue(), netem_dequeue() and
tbf_dequeue() (or qdisc_tree_decrease_qlen()) are redone.
With feedback from Herbert Xu and David S. Miller.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_deactivate() can skip rescheduling of a qdisc by qdisc_watchdog()
or other timer calling netif_schedule() after dev_queue_deactivate().
We prevent this checking aliveness before scheduling the timer. Since
during deactivation the root qdisc is available only as qdisc_sleeping
additional accessor qdisc_root_sleeping() is created.
With feedback from Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 1cfa26661a.
qdisc_destroy() runs fully under RTNL again and not from softint any
longer, so this change is no longer needed.
Signed-off-by: David S. Miller <davem@davemloft.net>
...Last block local var got just deleted.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon reports by Denys Fedoryshchenko, and feedback
and help from Jarek Poplawski and Herbert Xu.
We always either:
1) Never made an external reference to this qdisc.
or
2) Did a dev_deactivate() which purged all asynchronous
references.
So do not lock the qdisc when we call qdisc_destroy(),
it's illegal anyways as when we drop the lock this is
free'd memory.
Signed-off-by: David S. Miller <davem@davemloft.net>
Qdisc locks are initialized in the same function, qdisc_alloc(), so
lockdep can't distinguish tx qdisc lock from rx and reports "possible
recursive locking detected" when both these locks are taken eg. while
using act_mirred with ifb. This looks like a false positive. Anyway,
after this patch these locks will be reported more exactly.
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon initial discovery and patch by Jarek Poplawski.
The qdisc watchdogs can be attached to any qdisc, not just the root,
so make sure we schedule the correct one.
CBQ has a similar bug.
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon a bug report by Josip Rodin.
Packet schedulers should only return NET_XMIT_DROP iff
the packet really was dropped. If the packet does reach
the device after we return NET_XMIT_DROP then TCP can
crash because it depends upon the enqueue path return
values being accurate.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use return value from inner qdisc requeue when value returned isn't
NET_XMIT_SUCCESS, instead of always returning NET_XMIT_DROP.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can now kill them synchronously with all of the
previous dev_deactivate() cures.
This makes netdev destruction and shutdown saner as
the qdiscs hold references to the device.
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Jarek Poplawski <jarkao2@gmail.com>
When we are destroying non-root qdiscs, we need to lock
the root of the qdisc tree not the the qdisc itself.
Signed-off-by: David S. Miller <davem@davemloft.net>
The condition under which the previous qdisc has no more references
after we've attached &noop_qdisc is that both RUNNING and SCHED
are both seen clear while holding the root lock.
So just make specifically that check in the polling loop, instead
of this overly complex "check without then check with lock held"
sequence.
Signed-off-by: David S. Miller <davem@davemloft.net>
This new state lets dev_deactivate() mark a qdisc as having been
deactivated.
dev_queue_xmit() and ing_filter() check for this bit and do not
try to process the qdisc if the bit is set.
dev_deactivate() polls the qdisc after setting the bit, waiting
for both __QDISC_STATE_RUNNING and __QDISC_STATE_SCHED to clear.
This isn't perfect yet, but subsequent changesets will make it so.
This part is just one piece of the puzzle.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bug with spin_lock_bh() inserted instead of spin_unlock_bh() by
some recent patch.
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon discussions with Jarek P. and Herbert Xu.
First, we're testing the wrong qdisc. We just reset the device
queue qdiscs to &noop_qdisc and checking it's state is completely
pointless here.
We want to wait until the previous qdisc that was sitting at
the ->qdisc pointer is not busy any more. And that would be
->qdisc_sleeping.
Because of how we propagate the samples qdisc pointer down into
qdisc_run and friends via per-cpu ->output_queue and netif_schedule,
we have to wait also for the __QDISC_STATE_SCHED bit to clear as
well.
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes introduced a bug in htb_delete(): cl->parent->children
counter update misses checking cl->parent for NULL, which is used for
root classes, so deleting them causes an oops.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flushing must consistently return ENOMEM on failure of any allocation
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flushing of actions has been broken since we changed
the semantics of netlink parsed tb[X] to mean X is an attribute type.
This makes the flushing work.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since qdisc_stab_lock is used in qdisc_put_stab(), which is called in
BH context from __qdisc_destroy() RCU callback, softirq safe locking
is needed.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon bug reports by Stephen Hemminger.
We still had some cases using ->qdisc instead of ->qdisc_sleeping.
Also, qdisc_lookup() should return ingress qdiscs.
Signed-off-by: David S. Miller <davem@davemloft.net>
When an action is added several times with the same exact index
it gets deleted on every even-numbered attempt.
This fixes that issue.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy <kaber@trash.net> noticed that it would be nice to
handle NET_XMIT_BYPASS by NET_XMIT_SUCCESS with an internal qdisc flag
__NET_XMIT_BYPASS and to remove the mapping from dev_queue_xmit().
David Miller <davem@davemloft.net> spotted a serious bug in the first
version of this patch.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy <kaber@trash.net> noticed:
"The other problem that affects all qdiscs supporting actions is
TC_ACT_QUEUED/TC_ACT_STOLEN getting mapped to NET_XMIT_SUCCESS
even though the packet is not queued, corrupting upper qdiscs'
qlen counters."
and later explained:
"The reason why it translates it at all seems to be to not increase
the drops counter. Within a single qdisc this could be avoided by
other means easily, upper qdiscs would still increase the counter
when we return anything besides NET_XMIT_SUCCESS though.
This means we need a new NET_XMIT return value to indicate this to
the upper qdiscs. So I'd suggest to introduce NET_XMIT_STOLEN,
return that to upper qdiscs and translate it to NET_XMIT_SUCCESS
in dev_queue_xmit, similar to NET_XMIT_BYPASS."
David Miller <davem@davemloft.net> noticed:
"Maybe these NET_XMIT_* values being passed around should be a set of
bits. They could be composed of base meanings, combined with specific
attributes.
So you could say "NET_XMIT_DROP | __NET_XMIT_NO_DROP_COUNT"
The attributes get masked out by the top-level ->enqueue() caller,
such that the base meanings are the only thing that make their
way up into the stack. If it's only about communication within the
qdisc tree, let's simply code it that way."
This patch is trying to realize these ideas.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon a bug report by Jeff Kirsher.
Don't use qdisc_root_lock() in these cases as the root
qdisc could have been changed, and we'd thus lock the
wrong object.
Tested by Emil S Tantilov who confirms that this seems
to fix the problem.
Signed-off-by: David S. Miller <davem@davemloft.net>
When support for multiple TX queues were added, the
netif_tx_lock() routines we converted to iterate over
all TX queues and grab each queue's spinlock.
This causes heartburn for lockdep and it's not a healthy
thing to do with lots of TX queues anyways.
So modify this to use a top-level lock and a "frozen"
state for the individual TX queues.
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug report from Steven Jan Springl:
Issuing the following command causes a kernel oops:
tc qdisc add dev eth0 handle ffff: ingress
The problem mostly stems from all of the special case handling of
ingress qdiscs.
So, to fix this, do the grafting operation the same way we do for TX
qdiscs. Which means that dev_activate() and dev_deactivate() now do
the "qdisc_sleeping <--> qdisc" transitions on dev->rx_queue too.
Future simplifications are possible now, mainly because it is
impossible for dev_queue->{qdisc,qdisc_sleeping} to be NULL. There
are NULL checks all over to handle the ingress qdisc special case
that used to exist before this commit.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (39 commits)
[PATCH] fix RLIM_NOFILE handling
[PATCH] get rid of corner case in dup3() entirely
[PATCH] remove remaining namei_{32,64}.h crap
[PATCH] get rid of indirect users of namei.h
[PATCH] get rid of __user_path_lookup_open
[PATCH] f_count may wrap around
[PATCH] dup3 fix
[PATCH] don't pass nameidata to __ncp_lookup_validate()
[PATCH] don't pass nameidata to gfs2_lookupi()
[PATCH] new (local) helper: user_path_parent()
[PATCH] sanitize __user_walk_fd() et.al.
[PATCH] preparation to __user_walk_fd cleanup
[PATCH] kill nameidata passing to permission(), rename to inode_permission()
[PATCH] take noexec checks to very few callers that care
Re: [PATCH 3/6] vfs: open_exec cleanup
[patch 4/4] vfs: immutable inode checking cleanup
[patch 3/4] fat: dont call notify_change
[patch 2/4] vfs: utimes cleanup
[patch 1/4] vfs: utimes: move owner check into inode_change_ok()
[PATCH] vfs: use kstrdup() and check failing allocation
...
make it atomic_long_t; while we are at it, get rid of useless checks in affs,
hfs and hpfs - ->open() always has it equal to 1, ->release() - to 0.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This reverts commit f867e6af94.
Based upon discussions between Jarek and Patrick McHardy
this is field being set is more a config parameter than a
statistic. And we should add a true statistic to provide
this information if we really want it.
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes legacy reinvent-the-wheel type thing. The generic
machinery integrates much better to automated debugging aids
such as kerneloops.org (and others), and is unambiguous due to
better naming. Non-intuively BUG_TRAP() is actually equal to
WARN_ON() rather than BUG_ON() though some might actually be
promoted to BUG_ON() but I left that to future.
I could make at least one BUILD_BUG_ON conversion.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dump the "flows" number according to the number of active flows
instead of repeating the "limit".
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the needlessly global qdisc_class_hash_alloc() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by Dave:
This patch adds a function to get the driver name from a struct net_device,
and consequently uses this in the watchdog timeout handler to print as
part of the message.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit a0c80b80e0.
After discussions with Jamal and Herbert on netdev, we should
provide at least minimal prioritization at the qdisc level
even in multiqueue situations.
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed unused variable 'skb' in the dev_deactivate_queue function
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stab bits can't be referenced uniless the full
packet scheduler layer is enabled.
Reported by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add size table functions for qdiscs and calculate packet size in
qdisc_enqueue().
Based on patch by Patrick McHardy
http://marc.info/?l=linux-netdev&m=115201979221729&w=2
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet