Remove the static keyword from dw_pcie_ep_reset_bar() so that
pci-dra7xx.c does not need its own copy of dw_pcie_ep_reset_bar().
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Certain SoCs need to map the MSI address in raise_irq.
To map an address, you first need to call pci_epc_mem_alloc_addr(),
however, pci_epc_mem_alloc_addr() calls ioremap() (which can sleep).
Since raise_irq is only called from atomic context, we can't call
pci_epc_mem_alloc_addr() from raise_irq.
Pre-allocate a page in dw_pcie_ep_init(), so that this page can later
be used to map/unmap the MSI address in raise_irq.
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
Certain registers that pcie-designware-ep tries to write to are read-only
registers. However, these registers can become read/write if we first
enable the DBI_RO_WR_EN bit. Set/unset the DBI_RO_WR_EN bit before/after
writing these registers.
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
Previously, dw_pcie_ep_set_msi() wrote all bits in the Message Control
register, thus overwriting the PCI_MSI_FLAGS_64BIT bit.
By clearing the PCI_MSI_FLAGS_64BIT bit, we break MSI
on systems where the RC has set a 64 bit MSI address.
Fix dw_pcie_ep_set_msi() so that it only sets MMC bits.
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
Use the DMA-API to get the MSI address. This address will be written to
our PCI config space and to the register which determines which AXI
address the DWC IP will spoof for incoming MSI irqs.
Since it is a PCIe endpoint device, rather than the CPU, that is supposed
to write to the MSI address, the proper way to get the MSI address is by
using the DMA API, not by using virt_to_phys().
Using virt_to_phys() might work on some systems, but using the DMA API
should work on all systems.
This is essentially the same thing as allocating a buffer in a driver
to which the endpoint will write to. To do this, we use the DMA API.
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
Use only 4 KiB space from the available 1 GiB PCIe aperture to access
endpoint configuration space by dynamically moving the AFI_FPCI_BAR base
address. This frees more space for mapping endpoint device BARs on some
Tegra platforms.
The ->add_bus() and ->remove_bus() callbacks are now no longer needed,
so they can be removed.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
[treding@nvidia.com: various cleanups, update commit message]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Define dra7xx_pcie_shutdown() as a static function as it is not used
in other compilation units.
Signed-off-by: Vignesh R <vigneshr@ti.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
rcar_pcie_parse_request_of_pci_ranges() can fail and return an error
code, but this is not checked nor handled.
Fix this by adding the missing error handling.
Fixes: 5d2917d469 ("PCI: rcar: Convert to DT resource parsing API")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The changes in commit 9af275be15 ("PCI: xgene: Convert PCI scan API to
pci_scan_root_bus_bridge()") converted the xgene PCI host driver to
the new pci_scan_root_bus_bridge() bus scanning API but erroneously left
the existing pci_scan_child_bus() call in place which resulted in duplicate
PCI bus enumerations.
Remove the leftover pci_scan_child_bus() call to properly complete the API
conversion.
Fixes: 9af275be15 ("PCI: xgene: Convert PCI scan API to pci_scan_root_bus_bridge()")
Tested-by: Khuong Dinh <kdinh@apm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <stable@vger.kernel.org> # 4.13+
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Tanmay Inamdar <tinamdar@apm.com>
Fix child-node lookup during initialisation which was using the wrong
OF-helper and ended up searching the whole device tree depth-first
starting at the parent rather than just matching on its children.
To make things worse, the parent pci node could end up being prematurely
freed as of_find_node_by_name() drops a reference to its first argument.
Any matching child interrupt-controller node was also leaked.
Fixes: 0c4ffcfe1f ("PCI: keystone: Add TI Keystone PCIe driver")
Cc: stable <stable@vger.kernel.org> # 3.18
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
[lorenzo.pieralisi@arm.com: updated commit subject]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
->get_msi() now checks MSI_EN bit in the MSI CAPABILITY register to
find whether the host supports MSI instead of using the
MSI ADDRESS in the MSI CAPABILITY register.
This fixes the issue with the following sequence
'modprobe pci_endpoint_test' enables MSI
'rmmod pci_endpoint_test' disables MSI but MSI address (in EP's
capability register) has a valid value
'modprobe pci_endpoint_test no_msi=1' - Since MSI address (in EP's
capability register) has a valid value (set during the previous
insertion of the module), EP thinks host supports MSI.
Fixes: f8aed6ec62 ("PCI: dwc: designware: Add EP mode support")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
find_first_zero_bit()'s parameter 'size' is defined in bits,
not in bytes.
Calling find_first_zero_bit() with the wrong size unit
will lead to insidious bugs.
Fix this by calling find_first_zero_bit() with size BITS_PER_LONG,
rather than sizeof() and add missing find_first_zero_bit() return
handling.
Fixes: d746799116 ("PCI: endpoint: Introduce configfs entry for configuring EP functions")
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
func_no is a member of struct pci_epf.
Since struct pci_epf is used as an argument to pci_epc_add_epf() (to
bind an endpoint function to a controller), struct pci_epf.func_no
should be populated before calling pci_epc_add_epf().
Initialize the struct pci_epf.func_no member before calling
pci_epc_add_epf(), to fix the endpoint function binding to
an endpoint controller.
Fixes: d746799116 ("PCI: endpoint: Introduce configfs entry for configuring EP functions")
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
[lorenzo.pieralisi@arm.com: rewrote the commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Suggested-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
find_first_zero_bit()'s parameter 'size' is defined in bits,
not in bytes.
find_first_zero_bit() is called with size in bytes rather than bits,
which thus defines a too low upper limit, causing
dw_pcie_ep_inbound_atu() to assign iatu index #4 to both bar 4
and bar 5, which makes bar 5 overwrite the settings set by bar 4.
Since the sizes of the bitmaps are known, dynamically allocate the
bitmaps, and use the correct size when calling find_first_zero_bit().
Additionally, make sure that ep->num_ob_windows and ep->num_ib_windows,
which are obtained from device tree, are smaller than the maximum number
of iATUs (MAX_IATU_IN/MAX_IATU_OUT).
Fixes: f8aed6ec62 ("PCI: dwc: designware: Add EP mode support")
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
PCI_COMMAND_INTX_DISABLE is writable on the Ceton InfiniTV4, indicating
that the device supports disabling the INTx# signal, but it apparently
doesn't work.
Mark the device so we know we can't use PCI_COMMAND_INTX_DISABLE to disable
its interrupts.
Link: https://lkml.kernel.org/r/92a65068-60b2-c1a8-9e17-ac41fe3c5c93@code.jackst.com
Reported-by: John Strader <strader.john@code.jackst.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add device IDs for PSX 24xG3 and PSX 48xG3. These are valid devices that
were missing from the existing device ID table for the Switchtec driver.
Signed-off-by: Kelvin Cao <kelvin.cao@microsemi.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a new event type that is newly exposed by recent firmware. The event
will never occur if the firmware is too old. If user space tries to use
this event in an older kernel, it will just get an EINVAL which is
perfectly acceptable in the existing user space code.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
On AMD GPUs, we use several mechanisms to fetch the VBIOS ROM depending on
the platform. We try to read the ROM via the ROM BAR and fall back to
other methods in some cases. This leads to spurious error messages from
the PCI ROM code which are harmless in our case. This leads to bugs being
filed, etc. Change these to dev_info() rather than dev_err() to avoid
that.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=198077
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1462438
Link: https://bugs.freedesktop.org/show_bug.cgi?id=98798
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christian König <christian.koenig@amd.com
On arm, PCI_REASSIGN_ALL_RSRC is used only in pcibios_assign_all_busses(),
which helps decide whether to reconfigure bridge bus numbers. It has
nothing to do with BAR assignments. On arm64 and powerpc,
pcibios_assign_all_busses() tests PCI_REASSIGN_ALL_BUS, which makes more
sense.
Align arm with arm64 and powerpc, so they all use PCI_REASSIGN_ALL_BUS for
pcibios_assign_all_busses().
Remove PCI_REASSIGN_ALL_RSRC from the generic, Tegra, Versatile, and
R-Car drivers. These drivers are used only on arm or arm64, where
PCI_REASSIGN_ALL_RSRC is not used after this change, so removing it
should have no effect.
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
When a process uses sysfs and tries to mmap more space than is available in
a PCI BAR, we emit a warning and a backtrace. The mmap fails anyway, so
the backtrace is mainly for debugging. But in general we don't emit kernel
messages when syscalls return failure.
The similar procfs mmap path simply fails the mmap with no warning. Remove
the sysfs warning.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The file was converted from print_fn_descriptor_symbol() to %pF some time
ago (c9bbb4abb6 "PCI: use %pF instead of print_fn_descriptor_symbol()
in quirks.c"). kallsyms does not seem to be needed anymore.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When removing a bridge, pciehp_unconfigure_device() reads the
PCI_BRIDGE_CONTROL byte. If this is a surprise hot-unplug, the device is
already gone and the read returns ~0, which pciehp_unconfigure_device()
interprets as having PCI_BRIDGE_CTL_VGA set. This results in failure of
the remove operation:
pciehp 0000:00:1c.0:pcie004: Slot(0): Link Down
pciehp 0000:00:1c.0:pcie004: Slot(0): Card present
pciehp 0000:00:1c.0:pcie004: Cannot remove display device 0000:01:00.0
Because of this the hierarchy is left untouched preventing further hotplug
operations.
Now, it is not clear why the check is there in the first place and why we
would like to prevent removing a bridge if it has PCI_BRIDGE_CTL_VGA set.
In case of PCIe surprise hot-unplug, it would not even be possible to
prevent the removal.
Given this and the issue described above, I think it makes sense to drop
the whole PCI_BRIDGE_CONTROL check from pciehp_unconfigure_device(). While
there do the same for shpchp_configure_device() based on the same reasoning
and the fact that the same bug might trigger in standard PCI hotplug as
well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCIe Downstream Ports normally have only a Device 0 below them. To
optimize enumeration, we don't scan for other devices *unless* the
PCI_SCAN_ALL_PCIE_DEVS flag is set by set by quirks or the
"pci=pcie_scan_all" kernel parameter.
Previously PCI_SCAN_ALL_PCIE_DEVS only affected scanning below Switch
Downstream Ports, not Root Ports.
But the "Nemo" system, also known as the AmigaOne X1000, has a PA Semi Root
Port whose link leads to an AMD/ATI SB600 South Bridge. The Root Port is a
PCIe device, of course, but the SB600 contains only conventional PCI
devices with no visible PCIe port.
Simplify and restructure only_one_child() so that we scan for all possible
devices below Root Ports as well as Switch Downstream Ports when
PCI_SCAN_ALL_PCIE_DEVS is set.
This is enough to make Nemo work with "pci=pcie_scan_all". We would also
like to add a quirk to set PCI_SCAN_ALL_PCIE_DEVS automatically on Nemo so
users wouldn't have to use the "pci=pcie_scan_all" parameter, but we don't
have that yet.
Link: https://lkml.kernel.org/r/CAErSpo55Q8Q=5p6_+uu7ahnw+53ibVDNRXxrzRV9QnUr_9EUfw@mail.gmail.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=198057
Reported-and-Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Several of the interfaces defined in include/linux/pci-aspm.h are used only
internally from the PCI core:
pcie_aspm_init_link_state()
pcie_aspm_exit_link_state()
pcie_aspm_pm_state_change()
pcie_aspm_powersave_config_link()
pcie_aspm_create_sysfs_dev_files()
pcie_aspm_remove_sysfs_dev_files()
Move these to the internal drivers/pci/pci.h header so they don't clutter
the driver interface.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Enable Latency Tolerance Reporting (LTR). Note that LTR must be enabled in
the Root Port first, and must not be enabled in any downstream device
unless the Root Port and all intermediate Switches also support LTR.
See PCIe r3.1, sec 6.18.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Per PCIe r3.1, sec 5.5.1, LTR_L1.2_THRESHOLD determines whether we enter
the L1.2 Link state: if L1.2 is enabled and downstream devices have
reported that they can tolerate latency of at least LTR_L1.2_THRESHOLD, we
must enter L1.2 when CLKREQ# is de-asserted.
The implication is that LTR_L1.2_THRESHOLD is the time required to
transition the Link from L0 to L1.2 and back to L0, and per sec 5.5.3.3.1,
Figures 5-16 and 5-17, it appears that the absolute minimum time for those
transitions would be T(POWER_OFF) + T(L1.2) + T(POWER_ON) + T(COMMONMODE).
Therefore, compute LTR_L1.2_THRESHOLD as:
2us T(POWER_OFF)
+ 4us T(L1.2)
+ T(POWER_ON)
+ T(COMMONMODE)
= LTR_L1.2_THRESHOLD
Previously we set LTR_L1.2_THRESHOLD to a fixed value of 163840ns
(163.84us):
#define LTR_L1_2_THRESHOLD_BITS ((1 << 21) | (1 << 23) | (1 << 30))
((1 << 21) | (1 << 23) | (1 << 30)) = 0x40a00000
LTR_L1.2_THRESHOLD_Value = (0x40a00000 & 0x03ff0000) >> 16 = 0xa0 = 160
LTR_L1.2_THRESHOLD_Scale = (0x40a00000 & 0xe0000000) >> 29 = 0x2 (* 1024ns)
LTR_L1.2_THRESHOLD = 160 * 1024ns = 163840ns
Obviously this doesn't account for the circuit characteristics of different
implementations.
Note that while firmware may enable LTR, Linux itself currently does not
enable LTR. When L1.2 is enabled but LTR is not, LTR_L1.2_THRESHOLD is
ignored and we always enter L1.2 when it is enabled and CLKREQ# is
de-asserted. So this patch should not have any effect unless firmware
enables LTR.
Fixes: f1f0366dd6 ("PCI/ASPM: Calculate and save the L1.2 timing parameters")
Link: https://www.coreboot.org/pipermail/coreboot-gerrit/2015-March/021134.html
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Cc: Kenji Chen <kenji.chen@intel.com>
Cc: Patrick Georgi <pgeorgi@google.com>
Cc: Rajat Jain <rajatja@google.com>
PCIe correctable errors are corrected by hardware. Software may log them,
but no other software intervention is required.
There are two paths to enter the AER recovery code: (1) the native path
where Linux fields the AER interrupt and reads the AER registers directly,
and (2) the ACPI path where firmware reads the AER registers and hands them
off to Linux via the ACPI APEI path.
The AER do_recovery() function calls driver error reporting callbacks
(error_detected(), mmio_enabled(), resume(), etc), attempts recovery (for
fatal errors), and logs a "AER: Device recovery successful" message.
Since there's nothing to recover for correctable errors, the native path
already skips do_recovery(), so it doesn't call the driver callbacks and or
emit the message. Make the APEI path do the same.
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
It is incorrect to call pci_restore_state() for devices in low-power
states (D1-D3), as that involves the restoration of MSI setup which
requires MMIO to be operational and that is only the case in D0.
However, pci_pm_thaw_noirq() may do that if the driver's "freeze"
callbacks put the device into a low-power state, so fix it by making
it force devices into D0 via pci_set_power_state() instead of trying
to "update" their power state which is pointless.
Fixes: e60514bd44 (PCI/PM: Restore the status of PCI devices across hibernation)
Cc: 4.13+ <stable@vger.kernel.org> # 4.13+
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Maarten Lankhorst <dev@mblankhorst.nl>
Tested-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Maarten Lankhorst <dev@mblankhorst.nl>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Three sets of overlapping changes, two in the packet scheduler
and one in the meson-gxl PHY driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes an issue in two recent commits that may cause
pm_runtime_enable() to be called for too many times for some
devices during the "thaw" transition belonging to hibernation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=0D8g
-----END PGP SIGNATURE-----
Merge tag 'pm-4.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"This fixes an issue in two recent commits that may cause
pm_runtime_enable() to be called for too many times for some devices
during the "thaw" transition belonging to hibernation"
* tag 'pm-4.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / sleep: Avoid excess pm_runtime_enable() calls in device_resume()
Add pcim_set_mwi(), a device-managed version of pci_set_mwi().
First user is the Realtek r8169 driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_DEBUG_SLAB=y, and no PCIe card is inserted, the kernel crashes
during probe on r8a7791/koelsch:
rcar-pcie fe000000.pcie: PCIe link down
Unable to handle kernel paging request at virtual address 6b6b6b6b
(seeing this message requires earlycon and keep_bootcon).
Indeed, pci_free_host_bridge() frees the PCI host bridge, including the
embedded rcar_pcie object, so pci_free_resource_list() must not be called
afterwards.
To fix this, move the call to pci_free_resource_list() up, and update the
label name accordingly.
Fixes: ddd535f1ea ("PCI: rcar: Fix memory leak when no PCIe card is inserted")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Middle-layer code doing suspend-time optimizations for devices with
the DPM_FLAG_SMART_SUSPEND flag set (currently, the PCI bus type and
the ACPI PM domain) needs to make the core skip ->thaw_early and
->thaw callbacks for those devices in some cases and it sets the
power.direct_complete flag for them for this purpose.
However, it turns out that setting power.direct_complete outside of
the PM core is a bad idea as it triggers an excess invocation of
pm_runtime_enable() in device_resume().
For this reason, provide a helper to clear power.is_late_suspended
and power.is_suspended to be invoked by the middle-layer code in
question instead of setting power.direct_complete and make that code
call the new helper.
Fixes: c4b65157ae (PCI / PM: Take SMART_SUSPEND driver flag into account)
Fixes: 05087360fd (ACPI / PM: Take SMART_SUSPEND driver flag into account)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Add a pci_vf_drivers_autoprobe() interface. Setting autoprobe to false
on the PF prevents drivers from binding to VFs when they are enabled.
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Juan J. Alvarez <jjalvare@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add support for DPM_FLAG_LEAVE_SUSPENDED to the PCI bus type by
making it (a) set the power.may_skip_resume status bit for devices
that, from its perspective, may be left in suspend after system
wakeup from sleep and (b) return early from pci_pm_resume_noirq()
for devices whose remaining resume callbacks during the transition
under way are going to be skipped by the PM core.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Pull misc x86 fixes from Ingo Molnar:
- topology enumeration fixes
- KASAN fix
- two entry fixes (not yet the big series related to KASLR)
- remove obsolete code
- instruction decoder fix
- better /dev/mem sanity checks, hopefully working better this time
- pkeys fixes
- two ACPI fixes
- 5-level paging related fixes
- UMIP fixes that should make application visible faults more debuggable
- boot fix for weird virtualization environment
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
x86/decoder: Add new TEST instruction pattern
x86/PCI: Remove unused HyperTransport interrupt support
x86/umip: Fix insn_get_code_seg_params()'s return value
x86/boot/KASLR: Remove unused variable
x86/entry/64: Add missing irqflags tracing to native_load_gs_index()
x86/mm/kasan: Don't use vmemmap_populate() to initialize shadow
x86/entry/64: Fix entry_SYSCALL_64_after_hwframe() IRQ tracing
x86/pkeys/selftests: Fix protection keys write() warning
x86/pkeys/selftests: Rename 'si_pkey' to 'siginfo_pkey'
x86/mpx/selftests: Fix up weird arrays
x86/pkeys: Update documentation about availability
x86/umip: Print a warning into the syslog if UMIP-protected instructions are used
x86/smpboot: Fix __max_logical_packages estimate
x86/topology: Avoid wasting 128k for package id array
perf/x86/intel/uncore: Cache logical pkg id in uncore driver
x86/acpi: Reduce code duplication in mp_override_legacy_irq()
x86/acpi: Handle SCI interrupts above legacy space gracefully
x86/boot: Fix boot failure when SMP MP-table is based at 0
x86/mm: Limit mmap() of /dev/mem to valid physical addresses
x86/selftests: Add test for mapping placement for 5-level paging
...
There are no in-tree callers of ht_create_irq(), the driver interface for
HyperTransport interrupts, left. Remove the unused entry point and all the
supporting code.
See 8b955b0ddd ("[PATCH] Initial generic hypertransport interrupt
support").
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-pci@vger.kernel.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Link: https://lkml.kernel.org/r/20171122221337.3877.23362.stgit@bhelgaas-glaptop.roam.corp.google.com
bug fixes.
-----BEGIN PGP SIGNATURE-----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=svG8
-----END PGP SIGNATURE-----
Merge tag 'ntb-4.15' of git://github.com/jonmason/ntb
Pull ntb updates from Jon Mason:
"Support for the switchtec ntb and related changes. Also, a couple of
bug fixes"
[ The timing isn't great. I had asked people to send me pull requests
before my family vacation, and this code has not even been in
linux-next as far as I can tell. But Logan Gunthorpe pleaded for its
inclusion because the Switchtec driver has apparently been around for
a while, just never in linux-next - Linus ]
* tag 'ntb-4.15' of git://github.com/jonmason/ntb:
ntb: intel: remove b2b memory window workaround for Skylake NTB
NTB: make idt_89hpes_cfg const
NTB: switchtec_ntb: Update switchtec documentation with notes for NTB
NTB: switchtec_ntb: Add memory window support
NTB: switchtec_ntb: Implement scratchpad registers
NTB: switchtec_ntb: Implement doorbell registers
NTB: switchtec_ntb: Add link management
NTB: switchtec_ntb: Add skeleton NTB driver
NTB: switchtec_ntb: Initialize hardware for doorbells and messages
NTB: switchtec_ntb: Initialize hardware for memory windows
NTB: switchtec_ntb: Introduce initial NTB driver
NTB: Add check and comment for link up to mw_count() and mw_get_align()
NTB: Ensure ntb_mw_get_align() is only called when the link is up
NTB: switchtec: Add link event notifier callback
NTB: switchtec: Add NTB hardware register definitions
NTB: switchtec: Export class symbol for use in upper layer driver
NTB: switchtec: Move structure definitions into a common header
ntb: update maintainer list for Intel NTB driver
Seeing the Switchtec NTB hardware shares the same endpoint as the
management endpoint we utilize the class_interface API to register
an NTB driver for every Switchtec device in the system that has the
NTB class code.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
In order for the Switchtec NTB code to handle link change events we
create a notifier callback in the switchtec code which gets called
whenever an appropriate event interrupt occurs.
In order to preserve userspace's ability to follow these events,
we compare the event count with a stored copy from last time we
checked.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
We export the class pointer symbol and add an extern define in the
Switchtec header file.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Create the switchtec.h header in include/linux with hardware defines
and the switchtec_dev structure. Both moved directly from switchtec.c.
This is a prep patch for creating an NTB driver for Switchtec.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Summary of modules changes for the 4.15 merge window:
- Treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- Minor code cleanups
Signed-off-by: Jessica Yu <jeyu@kernel.org>
-----BEGIN PGP SIGNATURE-----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=c8vb
-----END PGP SIGNATURE-----
Merge tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux
Pull module updates from Jessica Yu:
"Summary of modules changes for the 4.15 merge window:
- treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- minor code cleanups"
* tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
module: Do not paper over type mismatches in module_param_call()
treewide: Fix function prototypes for module_param_call()
module: Prepare to convert all module_param_call() prototypes
kernel/module: Delete an error message for a failed memory allocation in add_module_usage()
- turn dma_cache_sync into a dma_map_ops instance and remove
implementation that purely are dead because the architecture
doesn't support noncoherent allocations
- add a flag for busses that need DMA configuration (Robin Murphy)
-----BEGIN PGP SIGNATURE-----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=ALJf
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.15' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- turn dma_cache_sync into a dma_map_ops instance and remove
implementation that purely are dead because the architecture doesn't
support noncoherent allocations
- add a flag for busses that need DMA configuration (Robin Murphy)
* tag 'dma-mapping-4.15' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: turn dma_cache_sync into a dma_map_ops method
sh: make dma_cache_sync a no-op
xtensa: make dma_cache_sync a no-op
unicore32: make dma_cache_sync a no-op
powerpc: make dma_cache_sync a no-op
mn10300: make dma_cache_sync a no-op
microblaze: make dma_cache_sync a no-op
ia64: make dma_cache_sync a no-op
frv: make dma_cache_sync a no-op
x86: make dma_cache_sync a no-op
floppy: consolidate the dummy fd_cacheflush definition
drivers: flag buses which demand DMA configuration
- proper use of the bool type (Thomas Meyer)
- constification of struct config_item_type (Bhumika Goyal)
-----BEGIN PGP SIGNATURE-----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=+tMO
-----END PGP SIGNATURE-----
Merge tag 'configfs-for-4.15' of git://git.infradead.org/users/hch/configfs
Pull configfs updates from Christoph Hellwig:
"A couple of configfs cleanups:
- proper use of the bool type (Thomas Meyer)
- constification of struct config_item_type (Bhumika Goyal)"
* tag 'configfs-for-4.15' of git://git.infradead.org/users/hch/configfs:
RDMA/cma: make config_item_type const
stm class: make config_item_type const
ACPI: configfs: make config_item_type const
nvmet: make config_item_type const
usb: gadget: configfs: make config_item_type const
PCI: endpoint: make config_item_type const
iio: make function argument and some structures const
usb: gadget: make config_item_type structures const
dlm: make config_item_type const
netconsole: make config_item_type const
nullb: make config_item_type const
ocfs2/cluster: make config_item_type const
target: make config_item_type const
configfs: make ci_type field, some pointers and function arguments const
configfs: make config_item_type const
configfs: Fix bool initialization/comparison
* pci/host-thunder:
PCI: Avoid slot reset if bridge itself is broken
PCI: Avoid bus reset if bridge itself is broken
PCI: Mark Cavium CN8xxx to avoid bus reset
* pci/host-tango:
PCI: tango: Add MSI controller support
PCI: Use of_pci_dma_range_parser_init() to reduce duplication
of/pci: Add of_pci_dma_range_parser_init() for dma-ranges parsing support
* pci/host-generic:
dt-bindings: PCI: designware: Add binding for Designware PCIe in ECAM mode
PCI: generic: Add support for Synopsys DesignWare RC in ECAM mode
* pci/virtualization:
PCI: Document reset method return values
PCI: Detach driver before procfs & sysfs teardown on device remove
PCI: Apply Cavium ThunderX ACS quirk to more Root Ports
PCI: Set Cavium ACS capability quirk flags to assert RR/CR/SV/UF
PCI: Restore ARI Capable Hierarchy before setting numVFs
PCI: Create SR-IOV virtfn/physfn links before attaching driver
PCI: Expose SR-IOV offset, stride, and VF device ID via sysfs
PCI: Cache the VF device ID in the SR-IOV structure
PCI: Add Kconfig PCI_IOV dependency for PCI_REALLOC_ENABLE_AUTO
PCI: Remove unused function __pci_reset_function()
PCI: Remove reset argument from pci_iov_{add,remove}_virtfn()
* pci/resource:
PCI: Fail pci_map_rom() if the option ROM is invalid
PCI: Move pci_map_rom() error path
x86/PCI: Enable a 64bit BAR on AMD Family 15h (Models 00-1f, 30-3f, 60-7f)
PCI: Add pci_resize_resource() for resizing BARs
PCI: Add resizable BAR infrastructure
PCI: Add PCI resource type mask #define
* pci/msi:
PCI/portdrv: Compute MSI/MSI-X IRQ vectors after final allocation
PCI/portdrv: Factor out Interrupt Message Number lookup
PCI/portdrv: Consolidate comments
PCI/portdrv: Add #defines for AER and DPC Interrupt Message Number masks
* pci/misc:
PCI: Fix kernel-doc build warning
PCI: Move PCI_QUIRKS to the PCI bus menu
alpha/PCI: Make pdev_save_srm_config() static
PCI: Remove unused declarations
PCI: Remove redundant pci_dev, pci_bus, resource declarations
PCI: Remove redundant pcibios_set_master() declarations
PCI/PME: Handle invalid data when reading Root Status
x86/pci/intel_mid_pci: Constify intel_mid_pci_ops and make it __initconst
PCI: Constify pci_dev_type structure
* pci/hotplug:
PCI: pciehp: Do not clear Presence Detect Changed during initialization
PCI: pciehp: Fix race condition handling surprise link down
PCI: Distribute available resources to hotplug-capable bridges
PCI: Distribute available buses to hotplug-capable bridges
PCI: Do not allocate more buses than available in parent
PCI: Open-code the two pass loop when scanning bridges
PCI: Move pci_hp_add_bridge() to drivers/pci/probe.c
PCI: Add for_each_pci_bridge() helper
PCI: shpchp: Convert timers to use timer_setup()
PCI: cpqphp: Convert timers to use timer_setup()
PCI: pciehp: Convert timers to use timer_setup()
PCI: ibmphp: Use common error handling code in unconfigure_boot_device()
* pci/aspm:
PCI/ASPM: Add L1 Substates definitions
PCI/ASPM: Reformat ASPM register definitions
PCI/ASPM: Use correct capability pointer to program LTR_L1.2_THRESHOLD
PCI/ASPM: Account for downstream device's Port Common_Mode_Restore_Time
PCI/ASPM: Deal with missing root ports in link state handling
Add and use #defines for L1 Substate register fields instead of hard-coding
the masks. Also update comments to use names from the spec. No functional
change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Previously we programmed the LTR_L1.2_THRESHOLD in the parent (upstream)
device using the capability pointer of the *child* (downstream) device,
which corrupted some random word of the parent's config space.
Use the parent's L1 SS capability pointer to program its
LTR_L1.2_THRESHOLD.
Fixes: aeda9adeba ("PCI/ASPM: Configure L1 substate settings")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
CC: stable@vger.kernel.org # v4.11+
CC: Rajat Jain <rajatja@google.com>
Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along with
phy and chipidea enhancements. There's also a lot of SPDX tags and
license boilerplate cleanups as well, which provide some churn in the
diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see happen.
All of these have been in linux-next with no reported issues for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgm/Vw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yktXwCdGgpInfOEvOGFd83EPDL7a1ncyc4AoM5wI8yl
1CeLipqVIN3IsMMJptvb
=zvDI
-----END PGP SIGNATURE-----
Merge tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along
with phy and chipidea enhancements. There's also a lot of SPDX tags
and license boilerplate cleanups as well, which provide some churn in
the diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see
happen.
All of these have been in linux-next with no reported issues for a
while"
* tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
usb: gadget: f_fs: Fix use-after-free in ffs_free_inst
USB: usbfs: compute urb->actual_length for isochronous
usb: core: message: remember to reset 'ret' to 0 when necessary
USB: typec: Remove remaining redundant license text
USB: typec: add SPDX identifiers to some files
USB: renesas_usbhs: rcar?.h: add SPDX tags
USB: chipidea: ci_hdrc_tegra.c: add SPDX line
USB: host: xhci-debugfs: add SPDX lines
USB: add SPDX identifiers to all remaining Makefiles
usb: host: isp1362-hcd: remove a couple of redundant assignments
USB: adutux: remove redundant variable minor
usb: core: add a new usb_get_ptm_status() helper
usb: core: add a 'type' parameter to usb_get_status()
usb: core: introduce a new usb_get_std_status() helper
usb: core: rename usb_get_status() 'type' argument to 'recip'
usb: core: add Status Type definitions
USB: gadget: Remove redundant license text
USB: gadget: function: Remove redundant license text
USB: gadget: udc: Remove redundant license text
USB: gadget: legacy: Remove redundant license text
...
- Relocate the OPP (Operating Performance Points) framework to its
own directory under drivers/ and add support for power domain
performance states to it (Viresh Kumar).
- Modify the PM core, the PCI bus type and the ACPI PM domain to
support power management driver flags allowing device drivers to
specify their capabilities and preferences regarding the handling
of devices with enabled runtime PM during system suspend/resume
and clean up that code somewhat (Rafael Wysocki, Ulf Hansson).
- Add frequency-invariant accounting support to the task scheduler
on ARM and ARM64 (Dietmar Eggemann).
- Fix PM QoS device resume latency framework to prevent "no
restriction" requests from overriding requests with specific
requirements and drop the confusing PM_QOS_FLAG_REMOTE_WAKEUP
device PM QoS flag (Rafael Wysocki).
- Drop legacy class suspend/resume operations from the PM core
and drop legacy bus type suspend and resume callbacks from
ARM/locomo (Rafael Wysocki).
- Add min/max frequency support to devfreq and clean it up
somewhat (Chanwoo Choi).
- Rework wakeup support in the generic power domains (genpd)
framework and update some of its users accordingly (Geert
Uytterhoeven).
- Convert timers in the PM core to use timer_setup() (Kees Cook).
- Add support for exposing the SLP_S0 (Low Power S0 Idle)
residency counter based on the LPIT ACPI table on Intel
platforms (Srinivas Pandruvada).
- Add per-CPU PM QoS resume latency support to the ladder cpuidle
governor (Ramesh Thomas).
- Fix a deadlock between the wakeup notify handler and the
notifier removal in the ACPI core (Ville Syrjälä).
- Fix a cpufreq schedutil governor issue causing it to use
stale cached frequency values sometimes (Viresh Kumar).
- Fix an issue in the system suspend core support code causing
wakeup events detection to fail in some cases (Rajat Jain).
- Fix the generic power domains (genpd) framework to prevent
the PM core from using the direct-complete optimization with
it as that is guaranteed to fail (Ulf Hansson).
- Fix a minor issue in the cpuidle core and clean it up a bit
(Gaurav Jindal, Nicholas Piggin).
- Fix and clean up the intel_idle and ARM cpuidle drivers (Jason
Baron, Len Brown, Leo Yan).
- Fix a couple of minor issues in the OPP framework and clean it
up (Arvind Yadav, Fabio Estevam, Sudeep Holla, Tobias Jordan).
- Fix and clean up some cpufreq drivers and fix a minor issue in
the cpufreq statistics code (Arvind Yadav, Bhumika Goyal, Fabio
Estevam, Gautham Shenoy, Gustavo Silva, Marek Szyprowski, Masahiro
Yamada, Robert Jarzmik, Zumeng Chen).
- Fix minor issues in the system suspend and hibernation core, in
power management documentation and in the AVS (Adaptive Voltage
Scaling) framework (Helge Deller, Himanshu Jha, Joe Perches,
Rafael Wysocki).
- Fix some issues in the cpupower utility and document that Shuah
Khan is going to maintain it going forward (Prarit Bhargava,
Shuah Khan).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=QTnx
-----END PGP SIGNATURE-----
Merge tag 'pm-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"There are no real big ticket items here this time.
The most noticeable change is probably the relocation of the OPP
(Operating Performance Points) framework to its own directory under
drivers/ as it has grown big enough for that. Also Viresh is now going
to maintain it and send pull requests for it to me, so you will see
this change in the git history going forward (but still not right
now).
Another noticeable set of changes is the modifications of the PM core,
the PCI subsystem and the ACPI PM domain to allow of more integration
between system-wide suspend/resume and runtime PM. For now it's just a
way to avoid resuming devices from runtime suspend unnecessarily
during system suspend (if the driver sets a flag to indicate its
readiness for that) and in the works is an analogous mechanism to
allow devices to stay suspended after system resume.
In addition to that, we have some changes related to supporting
frequency-invariant CPU utilization metrics in the scheduler and in
the schedutil cpufreq governor on ARM and changes to add support for
device performance states to the generic power domains (genpd)
framework.
The rest is mostly fixes and cleanups of various sorts.
Specifics:
- Relocate the OPP (Operating Performance Points) framework to its
own directory under drivers/ and add support for power domain
performance states to it (Viresh Kumar).
- Modify the PM core, the PCI bus type and the ACPI PM domain to
support power management driver flags allowing device drivers to
specify their capabilities and preferences regarding the handling
of devices with enabled runtime PM during system suspend/resume and
clean up that code somewhat (Rafael Wysocki, Ulf Hansson).
- Add frequency-invariant accounting support to the task scheduler on
ARM and ARM64 (Dietmar Eggemann).
- Fix PM QoS device resume latency framework to prevent "no
restriction" requests from overriding requests with specific
requirements and drop the confusing PM_QOS_FLAG_REMOTE_WAKEUP
device PM QoS flag (Rafael Wysocki).
- Drop legacy class suspend/resume operations from the PM core and
drop legacy bus type suspend and resume callbacks from ARM/locomo
(Rafael Wysocki).
- Add min/max frequency support to devfreq and clean it up somewhat
(Chanwoo Choi).
- Rework wakeup support in the generic power domains (genpd)
framework and update some of its users accordingly (Geert
Uytterhoeven).
- Convert timers in the PM core to use timer_setup() (Kees Cook).
- Add support for exposing the SLP_S0 (Low Power S0 Idle) residency
counter based on the LPIT ACPI table on Intel platforms (Srinivas
Pandruvada).
- Add per-CPU PM QoS resume latency support to the ladder cpuidle
governor (Ramesh Thomas).
- Fix a deadlock between the wakeup notify handler and the notifier
removal in the ACPI core (Ville Syrjälä).
- Fix a cpufreq schedutil governor issue causing it to use stale
cached frequency values sometimes (Viresh Kumar).
- Fix an issue in the system suspend core support code causing wakeup
events detection to fail in some cases (Rajat Jain).
- Fix the generic power domains (genpd) framework to prevent the PM
core from using the direct-complete optimization with it as that is
guaranteed to fail (Ulf Hansson).
- Fix a minor issue in the cpuidle core and clean it up a bit (Gaurav
Jindal, Nicholas Piggin).
- Fix and clean up the intel_idle and ARM cpuidle drivers (Jason
Baron, Len Brown, Leo Yan).
- Fix a couple of minor issues in the OPP framework and clean it up
(Arvind Yadav, Fabio Estevam, Sudeep Holla, Tobias Jordan).
- Fix and clean up some cpufreq drivers and fix a minor issue in the
cpufreq statistics code (Arvind Yadav, Bhumika Goyal, Fabio
Estevam, Gautham Shenoy, Gustavo Silva, Marek Szyprowski, Masahiro
Yamada, Robert Jarzmik, Zumeng Chen).
- Fix minor issues in the system suspend and hibernation core, in
power management documentation and in the AVS (Adaptive Voltage
Scaling) framework (Helge Deller, Himanshu Jha, Joe Perches, Rafael
Wysocki).
- Fix some issues in the cpupower utility and document that Shuah
Khan is going to maintain it going forward (Prarit Bhargava, Shuah
Khan)"
* tag 'pm-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (88 commits)
tools/power/cpupower: add libcpupower.so.0.0.1 to .gitignore
tools/power/cpupower: Add 64 bit library detection
intel_idle: Graceful probe failure when MWAIT is disabled
cpufreq: schedutil: Reset cached_raw_freq when not in sync with next_freq
freezer: Fix typo in freezable_schedule_timeout() comment
PM / s2idle: Clear the events_check_enabled flag
cpufreq: stats: Handle the case when trans_table goes beyond PAGE_SIZE
cpufreq: arm_big_little: make cpufreq_arm_bL_ops structures const
cpufreq: arm_big_little: make function arguments and structure pointer const
cpuidle: Avoid assignment in if () argument
cpuidle: Clean up cpuidle_enable_device() error handling a bit
ACPI / PM: Fix acpi_pm_notifier_lock vs flush_workqueue() deadlock
PM / Domains: Fix genpd to deal with drivers returning 1 from ->prepare()
cpuidle: ladder: Add per CPU PM QoS resume latency support
PM / QoS: Fix device resume latency framework
PM / domains: Rework governor code to be more consistent
PM / Domains: Remove gpd_dev_ops.active_wakeup() callback
soc: rockchip: power-domain: Use GENPD_FLAG_ACTIVE_WAKEUP
soc: mediatek: Use GENPD_FLAG_ACTIVE_WAKEUP
ARM: shmobile: pm-rmobile: Use GENPD_FLAG_ACTIVE_WAKEUP
...
Every Port that supports the L1.2 substate advertises its Port
Common_Mode_Restore_Time, i.e., the time the Port requires to re-establish
common mode when exiting L1.2 (see PCIe r3.1, sec 7.33.2).
Per sec 5.5.3.3.1, when exiting L1.2, the Downstream Port (the device at
the upstream end of the link) must send TS1 training sequences for at least
T(COMMONMODE) after it detects electrical idle exit on the Link. We want
this to be long enough for both ends of the Link, so we should set it to
the maximum of the Port Common_Mode_Restore_Time for the upstream and
downstream components on the Link.
Previously we only looked at the Port Common_Mode_Restore_Time of the
upstream device, so if the downstream device required more time, we didn't
program the upstream device's T(COMMONMODE) correctly.
Fixes: f1f0366dd6 ("PCI/ASPM: Calculate and save the L1.2 timing parameters")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Acked-by: Rajat Jain <rajatja@google.com>
CC: stable@vger.kernel.org # v4.11+
* pm-core:
ACPI / PM: Take SMART_SUSPEND driver flag into account
PCI / PM: Take SMART_SUSPEND driver flag into account
PCI / PM: Drop unnecessary invocations of pcibios_pm_ops callbacks
PM / core: Add SMART_SUSPEND driver flag
PCI / PM: Use the NEVER_SKIP driver flag
PM / core: Add NEVER_SKIP and SMART_PREPARE driver flags
PM / core: Convert timers to use timer_setup()
PM / core: Fix kerneldoc comments of four functions
PM / core: Drop legacy class suspend/resume operations
* pm-pci:
PCI / PM: Add dev_dbg() to print device suspend power states
PCI / PM: Do not resume any devices in pci_pm_prepare()
* pm-avs:
PM / AVS: Use %pS printk format for direct addresses
* pm-docs:
PM: docs: Fix formatting typo in devices.rst
Rename xgene_pcie_probe_bridge() to xgene_pcie_probe() to follow the
convention of other drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Rename xilinx_pcie_link_is_up() to xilinx_pcie_link_up() to follow the
convention of other drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Rename altera_pcie_link_is_up() to altera_pcie_link_up() to follow the
convention of other drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Ley Foon Tan <ley.foon.tan@intel.com>
Fix build error in kernel-doc notation:
../drivers/pci/pci.c:3479: ERROR: Unexpected indentation.
"::" tells the kernel-doc "reStructuredText" processor that the following
block is a literal block of some blob that should be kept as is.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
[bhelgaas: add hint about "::" meaning]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If we detect a invalid PCI option ROM (e.g., invalid ROM header signature),
we should unmap it immediately and fail. It doesn't make any sense to
return a mapped area with size of 0.
I have seen this case on Intel GVTg vGPU, which has no VBIOS. It will not
cause a real problem, but we should skip it as early as possible.
Signed-off-by: Changbin Du <changbin.du@intel.com>
[bhelgaas: split non-functional change into separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move pci_map_rom() error code to the end to prepare for adding another
error path. No functional change intended.
Signed-off-by: Changbin Du <changbin.du@intel.com>
[bhelgaas: split non-functional change into separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Localize PCI_QUIRKS in the PCI bus menu.
Move PCI_QUIRKS to the PCI bus menu instead of the (often broken) General
Setup EXPERT menu. The prompt still depends on EXPERT.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCIe PME and native hotplug share the same interrupt number, so hotplug
interrupts are also processed by PME. In some cases, e.g., a Link Down
interrupt, a device may be present but unreachable, so when we try to
read its Root Status register, the read fails and we get all ones data
(0xffffffff).
Previously, we interpreted that data as PCI_EXP_RTSTA_PME being set, i.e.,
"some device has asserted PME," so we scheduled pcie_pme_work_fn(). This
caused an infinite loop because pcie_pme_work_fn() tried to handle PME
requests until PCI_EXP_RTSTA_PME is cleared, but with the link down,
PCI_EXP_RTSTA_PME can't be cleared.
Check for the invalid 0xffffffff data everywhere we read the Root Status
register.
1469d17dd3 ("PCI: pciehp: Handle invalid data when reading from
non-existent devices") added similar checks in the hotplug driver.
Signed-off-by: Qiang Zheng <zhengqiang10@huawei.com>
[bhelgaas: changelog, also check in pcie_pme_work_fn(), use "~0" to follow
other similar checks]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The effective_affinity_mask is always set when an interrupt is assigned in
__assign_irq_vector() -> apic->cpu_mask_to_apicid(), e.g. for struct apic
apic_physflat: -> default_cpu_mask_to_apicid() ->
irq_data_update_effective_affinity(), but it looks d->common->affinity
remains all-1's before the user space or the kernel changes it later.
In the early allocation/initialization phase of an IRQ, we should use the
effective_affinity_mask, otherwise Hyper-V may not deliver the interrupt to
the expected CPU. Without the patch, if we assign 7 Mellanox ConnectX-3
VFs to a 32-vCPU VM, one of the VFs may fail to receive interrupts.
Tested-by: Adrian Suhov <v-adsuho@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jake Oshins <jakeo@microsoft.com>
Cc: stable@vger.kernel.org
Cc: Jork Loeser <jloeser@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
It is possible that the hotplug event has already happened before the
driver is attached to a PCIe hotplug downstream port. If we just clear the
status we never get the hotplug interrupt and thus the event will be
missed.
To make sure that does not happen, we leave Presence Detect Changed bit
untouched during initialization. Then once the event is unmasked we get an
interrupt and handle the hotplug event properly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
A surprise link down may retrain very quickly causing the same slot
generate a link up event before handling the link down event completes.
Since the link is active, the power off work queued from the first link
down will cause a second down event when power is disabled. However, the
link up event sets the slot state to POWERON_STATE before the event to
handle this is enqueued, making the second down event believe it needs to
do something.
This creates constant link up and down event cycle.
To prevent this it is better to handle each event at the time in order it
occurred, so change the driver to use ordered workqueue instead.
A normal device hotplug triggers two events (presense detect and link up)
that are already handled properly in the driver but we currently log an
error if we find an existing device in the slot. Since this is not an error
change the log level to be debug instead to avoid scaring users.
This is based on the original work by Ashok Raj.
Link: https://patchwork.kernel.org/patch/9469023
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The same problem that we have with bus space applies to other resources
as well. Linux only allocates the minimal amount of resources so that
the devices currently present barely fit there. This prevents extending
the chain later on because the resource windows allocated for hotplug
downstream ports are too small.
Follow what we already did for bus number and assign all available extra
resources to hotplug-capable bridges. This makes it possible to extend the
hierarchy later.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
System BIOS sometimes allocates extra bus space for hotplug-capable PCIe
root/downstream ports. This space is needed if the device plugged to the
port will have more hotplug-capable downstream ports. A good example of
this is Thunderbolt. Each Thunderbolt device contains a PCIe switch and
one or more hotplug-capable PCIe downstream ports where the daisy chain
can be extended.
Currently Linux only allocates minimal bus space to make sure all the
enumerated devices barely fit there. The BIOS reserved extra space is
not taken into consideration at all. Because of this we run out of bus
space pretty quickly when more PCIe devices are attached to hotplug
downstream ports in order to extend the chain.
Modify the PCI core so we distribute the available BIOS allocated bus space
equally between hotplug-capable bridges to make sure there is enough bus
space for extending the hierarchy later on.
Update kernel docs of the affected functions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
One can ask more buses to be reserved for hotplug bridges by passing
pci=hpbussize=N in the kernel command line. If the parent bus does not
have enough bus space available we incorrectly create child bus with the
requested number of subordinate buses.
In the example below hpbussize is set to one more than we have available
buses in the root port:
pci 0000:07:00.0: [8086:1578] type 01 class 0x060400
pci 0000:07:00.0: scanning [bus 00-00] behind bridge, pass 0
pci 0000:07:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:07:00.0: scanning [bus 00-00] behind bridge, pass 1
pci_bus 0000:08: busn_res: can not insert [bus 08-ff] under [bus 07-3f] (conflicts with (null) [bus 07-3f])
pci_bus 0000:08: scanning bus
...
pci_bus 0000:0a: bus scan returning with max=40
pci_bus 0000:0a: busn_res: [bus 0a-ff] end is updated to 40
pci_bus 0000:0a: [bus 0a-40] partially hidden behind bridge 0000:07 [bus 07-3f]
pci_bus 0000:08: bus scan returning with max=40
pci_bus 0000:08: busn_res: [bus 08-ff] end is updated to 40
Instead of allowing this, limit the subordinate number to be less than or
equal the maximum subordinate number allocated for the parent bus (if it
has any).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[bhelgaas: remove irrelevant dmesg messages]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The current scanning code is really hard to understand because it calls
the same function in a loop where pass value is changed without any
comments explaining it:
for (pass = 0; pass < 2; pass++)
for_each_pci_bridge(dev, bus)
max = pci_scan_bridge(bus, dev, max, pass);
Unfamiliar reader cannot tell easily what is the purpose of this loop
without looking at internals of pci_scan_bridge().
In order to make this bit easier to understand, open-code the loop in
pci_scan_child_bus() and pci_hp_add_bridge() with added comments.
No functional changes intended.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
There is not much point of having a file with a single function in it.
Instead we can just move pci_hp_add_bridge() to drivers/pci/probe.c and
make it available always when PCI core is enabled.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[bhelgaas: convert printk to dev_err()]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The following pattern is often used:
list_for_each_entry(dev, &bus->devices, bus_list) {
if (pci_is_bridge(dev)) {
...
}
}
Add a for_each_pci_bridge() helper to make that code easier to write and
read by reducing indentation level. It also saves one or few lines of code
in each occurrence.
Convert PCI core parts here at the same time.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[bhelgaas: fold in http://lkml.kernel.org/r/20171013165352.25550-1-andriy.shevchenko@linux.intel.com]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Quentin Lambert <lambert.quentin@gmail.com>
Cc: Aleksandr Bezzubikov <zuban32s@gmail.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. This has the result of fixing
pushbutton_helper_thread(), which was truncating the event pointer to 32
bits.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Quentin Lambert <lambert.quentin@gmail.com>
Cc: Aleksandr Bezzubikov <zuban32s@gmail.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. This fixes what appears to be a bug
in passing the wrong pointer to the timer handler (address of ctrl pointer
instead of ctrl pointer).
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Mayurkumar Patel <mayurkumar.patel@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Combine two error paths that emit the same message and return the same
error code.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some of the PCIe services such as AER are being left enabled during
shutdown. This might cause spurious AER errors while SOC is being powered
down.
Clean up the PCIe services gracefully during shutdown to clear these false
positives.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Make the PCI bus type take DPM_FLAG_SMART_SUSPEND into account in its
system-wide PM callbacks and make sure that all code that should not
run in parallel with pci_pm_runtime_resume() is executed in the "late"
phases of system suspend, freeze and poweroff transitions.
[Note that the pm_runtime_suspended() check in pci_dev_keep_suspended()
is an optimization, because if is not passed, all of the subsequent
checks may be skipped and some of them are much more overhead in
general.]
Also use the observation that if the device is in runtime suspend
at the beginning of the "late" phase of a system-wide suspend-like
transition, its state cannot change going forward (runtime PM is
disabled for it at that time) until the transition is over and the
subsequent system-wide PM callbacks should be skipped for it (as
they generally assume the device to not be suspended), so add checks
for that in pci_pm_suspend_late/noirq(), pci_pm_freeze_late/noirq()
and pci_pm_poweroff_late/noirq().
Moreover, if pci_pm_resume_noirq() or pci_pm_restore_noirq() is
called during the subsequent system-wide resume transition and if
the device was left in runtime suspend previously, its runtime PM
status needs to be changed to "active" as it is going to be put
into the full-power state, so add checks for that too to these
functions.
In turn, if pci_pm_thaw_noirq() runs after the device has been
left in runtime suspend, the subsequent "thaw" callbacks need
to be skipped for it (as they may not work correctly with a
suspended device), so set the power.direct_complete flag for the
device then to make the PM core skip those callbacks.
In addition to the above add a core helper for checking if
DPM_FLAG_SMART_SUSPEND is set and the device runtime PM status is
"suspended" at the same time, which is done quite often in the new
code (and will be done elsewhere going forward too).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The only user of non-empty pcibios_pm_ops is s390 and it only uses
"noirq" callbacks, so drop the invocations of the other pcibios_pm_ops
callbacks from the PCI PM code.
That will allow subsequent changes to be somewhat simpler.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Replace the PCI-specific flag PCI_DEV_FLAGS_NEEDS_RESUME with the
PM core's DPM_FLAG_NEVER_SKIP one everywhere and drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
The motivation for this change is to provide a way to work around
a problem with the direct-complete mechanism used for avoiding
system suspend/resume handling for devices in runtime suspend.
The problem is that some middle layer code (the PCI bus type and
the ACPI PM domain in particular) returns positive values from its
system suspend ->prepare callbacks regardless of whether the driver's
->prepare returns a positive value or 0, which effectively prevents
drivers from being able to control the direct-complete feature.
Some drivers need that control, however, and the PCI bus type has
grown its own flag to deal with this issue, but since it is not
limited to PCI, it is better to address it by adding driver flags at
the core level.
To that end, add a driver_flags field to struct dev_pm_info for flags
that can be set by device drivers at the probe time to inform the PM
core and/or bus types, PM domains and so on on the capabilities and/or
preferences of device drivers. Also add two static inline helpers
for setting that field and testing it against a given set of flags
and make the driver core clear it automatically on driver remove
and probe failures.
Define and document two PM driver flags related to the direct-
complete feature: NEVER_SKIP and SMART_PREPARE that can be used,
respectively, to indicate to the PM core that the direct-complete
mechanism should never be used for the device and to inform the
middle layer code (bus types, PM domains etc) that it can only
request the PM core to use the direct-complete mechanism for
the device (by returning a positive value from its ->prepare
callback) if it also has been requested by the driver.
While at it, make the core check pm_runtime_suspended() when
setting power.direct_complete so that it doesn't need to be
checked by ->prepare callbacks.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several function prototypes for the set/get functions defined by
module_param_call() have a slightly wrong argument types. This fixes
those in an effort to clean up the calls when running under type-enforced
compiler instrumentation for CFI. This is the result of running the
following semantic patch:
@match_module_param_call_function@
declarer name module_param_call;
identifier _name, _set_func, _get_func;
expression _arg, _mode;
@@
module_param_call(_name, _set_func, _get_func, _arg, _mode);
@fix_set_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._set_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _set_func(
-_val_type _val
+const char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
@fix_get_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._get_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _get_func(
-_val_type _val
+char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
Two additional by-hand changes are included for places where the above
Coccinelle script didn't notice them:
drivers/platform/x86/thinkpad_acpi.c
fs/lockd/svc.c
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
*) Add support in phy core to perform phy calibration
*) Return NULL for optional PHY's even if CONFIG_GENERIC_PHY is not selected
*) Add USB Phy driver for Broadcom STB SoCs
*) Add support to force mediatek PHY with USB OTG function to enter
a specific mode
*) Calibrate rockchip-typec PHY according to docs
*) Enable dual route feature for sun4i-usb in V3s SoC
*) Use dr_mode dt property to enable otg capability in rcar-gen3-usb2
*) Add driver data to specify dedicated otg pins in rcar-gen3-usb2 driver
*) Configure the RX equalizer of brcm-sata PHY
*) Update pcie phy settings for ti-pipe3 phy
*) Add set_mode callback in qcom-ufs-qmp-14nm phy
*) Use PHY callbacks in phy-qcom-ufs instead of export APIs
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=VvPn
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.15_v1' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.15
*) Add support in phy core to perform phy calibration
*) Return NULL for optional PHY's even if CONFIG_GENERIC_PHY is not selected
*) Add USB Phy driver for Broadcom STB SoCs
*) Add support to force mediatek PHY with USB OTG function to enter
a specific mode
*) Calibrate rockchip-typec PHY according to docs
*) Enable dual route feature for sun4i-usb in V3s SoC
*) Use dr_mode dt property to enable otg capability in rcar-gen3-usb2
*) Add driver data to specify dedicated otg pins in rcar-gen3-usb2 driver
*) Configure the RX equalizer of brcm-sata PHY
*) Update pcie phy settings for ti-pipe3 phy
*) Add set_mode callback in qcom-ufs-qmp-14nm phy
*) Use PHY callbacks in phy-qcom-ufs instead of export APIs
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The pci_reset_function() path may try several different reset methods:
device-specific resets, PCIe Function Level Resets, PCI Advanced Features
Function Level Reset, etc.
Add a comment about what the return values from these methods mean. If one
of the methods fails, in some cases we want to continue and try the next
one in the list, but sometimes we want to stop trying.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a pci_resize_resource() interface to allow device drivers to resize
BARs of their devices.
This is useful for devices with large local storage, e.g., graphics
devices. These devices often only expose 256MB BARs initially to be
compatible with 32-bit systems.
This function only tries to reprogram the windows of the bridge directly
above the requesting device and only the BAR of the same type (usually mem,
64bit, prefetchable). This is done to avoid disturbing other drivers by
changing the BARs of their devices.
Drivers should use the following sequence to resize their BARs:
1. Disable memory decoding of the device using the PCI cfg dword.
2. Use pci_release_resource() to release all BARs which can move during the
resize, including the one you want to resize.
3. Call pci_resize_resource() for each BAR you want to resize.
4. Call pci_assign_unassigned_bus_resources() to reassign new locations
for all BARs which are not resized, but could move.
5. If everything worked as expected, enable memory decoding in the device
again using the PCI cfg dword.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When removing a device, for example a VF being removed due to SR-IOV
teardown, a "soft" hot-unplug via 'echo 1 > remove' in sysfs, or an actual
hot-unplug, we first remove the procfs and sysfs attributes for the device
before attempting to release the device from any driver bound to it.
Unbinding the driver from the device can take time. The device might need
to write out data or it might be actively in use. If it's in use by
userspace through a vfio driver, the unbind might block until the user
releases the device. This leads to a potentially non-trivial amount of
time where the device exists, but we've torn down the interfaces that
userspace uses to examine devices, for instance lspci might generate this
sort of error:
pcilib: Cannot open /sys/bus/pci/devices/0000:01:0a.3/config
lspci: Unable to read the standard configuration space header of device 0000:01:0a.3
We don't seem to have any dependence on this teardown ordering in the
kernel, so let's unbind the driver first, which is also more symmetric with
the instantiation of the device in pci_bus_add_device().
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a HiSilicon STB SoC PCIe controller driver. This controller is based
on the DesignWare PCIe core.
Signed-off-by: Jianguo Sun <sunjianguo1@huawei.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add resizable BAR infrastructure, including defines and helper functions to
read the possible sizes of a BAR and update its size. See PCIe r3.1, sec
7.22.
Link: https://pcisig.com/sites/default/files/specification_documents/ECN_Resizable-BAR_24Apr2008.pdf
Signed-off-by: Christian König <christian.koenig@amd.com>
[bhelgaas: rename to functions with "rebar" (to match #defines), drop shift
#defines, drop "_MASK" suffixes, fix typos, fix kerneldoc]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Add a #define for the PCI resource type mask. We use this mask multiple
times in the bus setup.
Signed-off-by: Christian König <christian.koenig@amd.com>
[bhelgaas: move to setup-bus.c]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
PCI core access configuration space registers in resume_noirq callbacks.
In the case of dra7xx, PIPE3 PHY connected to PCIe controller has to be
enabled before accessing configuration space registers. Since
PIPE3 PHY is enabled by only configuring control module registers, no
aborts has been observed so far (though during noirq stage, interface
clock of PIPE3 PHY is not enabled).
With new TRM updates, PIPE3 PHY has to be initialized (PIPE3 PHY
registers has to be accessed) as well which requires the interface
clock of PIPE3 PHY to be enabled. The interface clock of PIPE3 PHY is
derived from OCP2SCP and hence PCIe PHY is modeled as a child of
OCP2SCP. Since pm_runtime is not enabled during noirq stage,
pm_runtime_get_sync done in phy_init doesn't enable
OCP2SCP clocks resulting in abort when PIPE3 PHY registers are
accessed.
Create a function dependency between PCIe and PHY here to make
sure PCIe is suspended before PCIe PHY/OCP2SCP and resumed after
PCIe PHY/OCP2SCP.
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
When setting up portdrv MSI/MSI-X interrupts, we previously allocated the
maximum possible number of vectors, read the Interrupt Message Numbers for
each service, saved the IRQ for each, freed the vectors, and finally used
the largest Message Number to reallocate only as many vectors as we need.
The problem is that freeing the vectors invalidates their IRQs, so the
saved IRQ numbers may now be invalid, which can result in errors like
this:
pcie_pme: probe of 0000:00:00.0:pcie001 failed with error -22
pciehp 0000:00:00.0:pcie004: Cannot get irq 20 for the hotplug controller
aer: probe of 0000:00:00.0:pcie002 failed with error -22
dpc 0000:00:00.0:pcie010: request IRQ22 failed: -22
Change the setup so we save the Interrupt Message Numbers (not the IRQs)
before we free the original setup, then use the Message Numbers to compute
the IRQs (via pci_irq_vector()) *after* we reallocate the vectors.
This should always be safe for MSI-X because the Message Numbers are fixed.
For MSI, the hardware is allowed to change Message Numbers when we update
the MSI Multiple Message Enable field when reallocating the vectors, but
since we allocate enough vectors to accommodate the largest Message Number
we found, that's unlikely. See PCIe r3.1, sec 7.8.2, 7.10.10, 7.31.2.
Fixes: 3674cc49da ("PCI/portdrv: Use pci_irq_alloc_vectors()")
Based-on-patch-by: Dongdong Liu <liudongdong3@huawei.com>
Tested-by: Dongdong Liu <liudongdong3@huawei.com> # HiSilicon hip08
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
PTR_ERR should access the value just tested by IS_ERR, otherwise the wrong
error code will be returned.
Fixes: 2eeb02b285 ("PCI: faraday: Add clock handling")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
By default, when the PCIe controller experiences an erroneous completion
from an external completer for its outbound non-posted request, it sends
an OKAY response to the device's internal AXI slave system interface.
However, this default system error response behavior cannot be used for
other types of outbound non-posted requests. For example, the outbound
memory read transaction requires an actual ERROR response, like UR
completion or completion timeout.
Fix this by forwarding the error response of the non-posted request.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Freescale PCIe controller advertises the MSI/MSI-X capability in both
RC and Endpoint mode, but in RC mode it doesn't support MSI/MSI-X by
itself; it can only transfer MSI/MSI-X from downstream devices.
Add a quirk to prevent use of MSI/MSI-X in RC mode.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Minghuan Lian <minghuan.Lian@nxp.com>
Factor out Interrupt Message Number lookup from the MSI/MSI-X interrupt
setup. One side effect is that we only have to check once to see if we
have enough vectors for all the services. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Consolidate some repetitive comments so we can see the code better. No
functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
In the AER case, the mask isn't strictly necessary because there are no
higher-order bits above the Interrupt Message Number, but using a #define
will make it possible to grep for it.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Extend the Cavium ThunderX ACS quirk to cover more device IDs and restrict
it to only Root Ports.
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
[bhelgaas: changelog, stable tag]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v4.12+
We do not want the common dma_configure() pathway to apply
indiscriminately to all devices, since there are plenty of buses which
do not have DMA capability, and if their child devices were used for
DMA API calls it would only be indicative of a driver bug. However,
there are a number of buses for which DMA is implicitly expected even
when not described by firmware - those we whitelist with an automatic
opt-in to dma_configure(), assuming that the DMA address space and the
physical address space are equivalent if not otherwise specified.
Commit 7232888366 ("of: restrict DMA configuration") introduced a
short-term fix by comparing explicit bus types, but this approach is far
from pretty, doesn't scale well, and fails to cope at all with bus
drivers which may be built as modules, like host1x. Let's refine things
by making that opt-in a property of the bus type, which neatly addresses
those problems and lets the decision of whether firmware description of
DMA capability should be optional or mandatory stay internal to the bus
drivers themselves.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Make config_item_type structures const as they are either passed to a
function having the argument as const or stored in the const "ci_type"
field of a config_item structure.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The Cavium ThunderX (CN8XXX) family of PCIe Root Ports does not advertise
an ACS capability. However, the RTL internally implements similar
protection as if ACS had Request Redirection, Completion Redirection,
Source Validation, and Upstream Forwarding features enabled.
Change Cavium ACS capabilities quirk flags accordingly.
Fixes: b404bcfbf0 ("PCI: Add ACS quirk for all Cavium devices")
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
[bhelgaas: tidy changelog, comment, stable tag]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v4.6+: b77d537d00d0: PCI: Apply Cavium ACS quirk only to CN81xx/CN83xx/CN88xx devices
Add Tegra186 PCIe support. UPHY programming is performed by BPMP; PHY
enable calls are not required for Tegra186 PCIe.
Power partition ungate is done by BPMP powergate driver. The Tegra186
DT description must include a "power-domains" property, which results in
dev->pm_domain being set.
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
[bhelgaas: add "power-domains" reference]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
If interrupt reservation mode is enabled then the PCI/MSI interrupts must
be reactivated after early activation.
Make sure that all callers of pci_msi_create_irq_domain() have the
MSI_FLAG_MUST_REACTIVATE set when reservation mode is enabled.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Josh Poulson <jopoulso@microsoft.com>
Cc: Mihai Costache <v-micos@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-pci@vger.kernel.org
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Simon Xiao <sixiao@microsoft.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jork Loeser <Jork.Loeser@microsoft.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: devel@linuxdriverproject.org
Cc: KY Srinivasan <kys@microsoft.com>
Link: https://lkml.kernel.org/r/20171017075600.448649905@linutronix.de
Add support for allocating multiple MSIs at the same time, so that the
MSI_FLAG_MULTI_PCI_MSI flag can be added to the msi_domain_info structure.
Avoid storing the hwirq in the low 5 bits of the message data, as it is
used by the device. Also fix an endianness problem by using readl().
Signed-off-by: Sandor Bodo-Merle <sbodomerle@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Add support for ls1012a.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Minghuan Lian <minghuan.Lian@nxp.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
The Tegra PCI host controller can generate configuration space accesses
with byte, word and dword granularity for devices. Only root ports can't
have their configuration space accessed in this way.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add shutdown handler to cleanly turn off clocks. This will help in cases of
kexec where in a new kernel can boot abruptly.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
When checking to see if a PCI slot can safely be reset, we previously
checked to see if any of the children had their PCI_DEV_FLAGS_NO_BUS_RESET
flag set.
Some PCIe root port bridges do not behave well after a slot reset, and may
cause the device in the slot to become unusable.
Add a check for PCI_DEV_FLAGS_NO_BUS_RESET being set in the bridge device
to prevent the slot from being reset.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
When checking to see if a PCI bus can safely be reset, we previously
checked to see if any of the children had their PCI_DEV_FLAGS_NO_BUS_RESET
flag set. Children marked with that flag are known not to behave well
after a bus reset.
Some PCIe root port bridges also do not behave well after a bus reset,
sometimes causing the devices behind the bridge to become unusable.
Add a check for PCI_DEV_FLAGS_NO_BUS_RESET being set in the bridge device
to allow these bridges to be flagged, and prevent their secondary buses
from being reset.
Signed-off-by: David Daney <david.daney@cavium.com>
[jglauber@cavium.com: fixed typo]
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Root ports of cn8xxx do not function after bus reset when used with some
e1000e and LSI HBA devices. Add a quirk to prevent bus reset on these root
ports.
Signed-off-by: David Daney <david.daney@cavium.com>
[jglauber@cavium.com: fixed typo and whitespaces]
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
struct pci_host_bridge gained hooks to map/swizzle IRQs, so that the IRQ
mapping can be done automatically by PCI core code through the
pci_assign_irq() function instead of resorting to arch-specific
implementation callbacks to carry out the same task which force PCI host
bridge drivers implementation to implement per-arch kludges to carry out a
task that is inherently architecture agnostic.
Commit 769b461fc0 ("arm64: PCI: Drop DT IRQ allocation from
pcibios_alloc_irq()") was assuming all PCI host controller drivers had been
converted to use ->map_irq(), but that wasn't the case: pci-aardvark had
not been converted. Due to this, it broke the support for legacy PCI
interrupts when using the pci-aardvark driver (used on Marvell Armada 3720
platforms).
In order to fix this, we make sure the ->map_irq and ->swizzle_irq fields
of pci_host_bridge are properly filled in.
Fixes: 769b461fc0 ("arm64: PCI: Drop DT IRQ allocation from pcibios_alloc_irq()")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v4.13+
In the restore path, we previously read PCI_SRIOV_VF_OFFSET and
PCI_SRIOV_VF_STRIDE before restoring PCI_SRIOV_CTRL_ARI:
pci_restore_state
pci_restore_iov_state
sriov_restore_state
pci_iov_set_numvfs
pci_read_config_word(... PCI_SRIOV_VF_OFFSET, &iov->offset)
pci_read_config_word(... PCI_SRIOV_VF_STRIDE, &iov->stride)
pci_write_config_word(... PCI_SRIOV_CTRL, iov->ctrl)
But per SR-IOV r1.1, sec 3.3.3.5, the device can use PCI_SRIOV_CTRL_ARI to
determine PCI_SRIOV_VF_OFFSET and PCI_SRIOV_VF_STRIDE. Therefore, this
path, which is used for suspend/resume and AER recovery, can corrupt
iov->offset and iov->stride.
Since the iov state is associated with the device, not the driver, if we
reload the driver, it will use the the corrupted data, which may cause
crashes like this:
kernel BUG at drivers/pci/iov.c:157!
RIP: 0010:pci_iov_add_virtfn+0x2eb/0x350
Call Trace:
pci_enable_sriov+0x353/0x440
ixgbe_pci_sriov_configure+0xd5/0x1f0 [ixgbe]
sriov_numvfs_store+0xf7/0x170
dev_attr_store+0x18/0x30
sysfs_kf_write+0x37/0x40
kernfs_fop_write+0x120/0x1b0
vfs_write+0xb5/0x1a0
SyS_write+0x55/0xc0
Restore PCI_SRIOV_CTRL_ARI before calling pci_iov_set_numvfs(), then
restore the rest of PCI_SRIOV_CTRL (which may set PCI_SRIOV_CTRL_VFE)
afterwards.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
[bhelgaas: changelog, add comment, also clear ARI if necessary]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Emil Tantilov <emil.s.tantilov@intel.com>
When creating virtual functions, create the "virtfn%u" and "physfn" links
in sysfs *before* attaching the driver instead of after. When we attach
the driver to the new virtual network interface first, there is a race when
the driver attaches to the new sends out an "add" udev event, and the
network interface naming software (biosdevname or systemd, for example)
tries to look at these links.
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Expose the SR-IOV device offset, stride, and VF device ID via sysfs to make
it easier for userspace applications to consume them.
Signed-off-by: Filippo Sironi <sironi@amazon.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This reverts commit d7bd554f27.
It turns out that Tegra20 has a bug in the implementation of the MSI
target address register (which is worked around by the existence of the
struct tegra_pcie_soc.msi_base_shift parameter) that restricts the MSI
target memory to the lower 32 bits of physical memory on that particular
generation. The offending patch causes a regression on TrimSlice, which
is a Tegra20-based device and has a PCI network interface card.
An initial, simpler fix was to change the MSI target address for Tegra20
only, but it was pointed out that the offending commit also prevents the
use of 32-bit only MSI capable devices, even on later chips. Technically
this was never guaranteed to work with the prior code in the first place
because the allocated page could have resided beyond the 4 GiB boundary,
but it is still possible that this could've introduced a regression.
The proper fix that was settled on is to select a fixed address within
the lowest 32 bits of physical address space that is otherwise unused,
but testing of that patch has provided mixed results that are not fully
understood yet.
Given all of the above and the relative urgency to get this fixed in
v4.13, revert the offending commit until a universal fix is found.
Fixes: d7bd554f27 ("PCI: tegra: Do not allocate MSI target memory")
Reported-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Reported-by: Erik Faye-Lund <kusmabite@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # 4.13.x
Some implementations of the Synopsys DesignWare PCIe controller implement
a so-called ECAM shift mode, which allows a static memory window to be
configured that covers the configuration space of the entire bus range.
Usually, when the firmware performs all the low level configuration that is
required to expose this controller in a fully ECAM compatible manner, we
can simply describe it as "pci-host-ecam-generic" and be done with it.
However, in some cases (e.g., the Marvell Armada 80x0 as well as the
Socionext SynQuacer Soc), the IP was synthesized with an ATU window
granularity that does not allow the first bus to be mapped in a way that
prevents the device on the downstream port from appearing more than once,
and so we still need special handling in software to drive this static
almost-ECAM configuration.
So extend the pci-host-generic driver so it can support these controllers
as well, by adding special config space accessors that take the above quirk
into account.
Note that, unlike most drivers for this IP, this driver does not expose a
fake bridge device at B/D/F 00:00.0. There is no point in doing so, given
that this is not a true bridge, and does not require any windows to be
configured in order for the downstream device to operate correctly.
Omitting it also prevents the PCI resource allocation routines from handing
out BAR space to it unnecessarily.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[bhelgaas: factor out pci_dw_valid_device(), add pci_dw_ecam_map_bus() and
use generic read/write functions]
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Will Deacon <will.deacon@arm.com>
The structure event_regs is local to the source and does not need to be in
global scope, so make it static.
Cleans up sparse warning:
symbol 'event_regs' was not declared. Should it be static
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Logan Gunthorpe <logang@deltatee.com>
Cache the VF device ID in the SR-IOV structure and use it instead of
reading it over and over from the PF config space capability.
Signed-off-by: Filippo Sironi <sironi@amazon.de>
[bhelgaas: rename to "vf_device" to match pci_dev->device]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Ensure only valid Kconfig configurations for PCI_REALLOC_ENABLE_AUTO. This
is done by selecting PCI_IOV, which is required by PCI_REALLOC_ENABLE_AUTO
to work.
Signed-off-by: Sascha El-Sharkawy <elscha@sse.uni-hildesheim.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The last caller of __pci_reset_function() has been removed. Remove the
function as well.
Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The "reset" argument passed to pci_iov_add_virtfn() and
pci_iov_remove_virtfn() is always zero since 46cb7b1bd8 ("PCI: Remove
unused SR-IOV VF Migration support")
Remove the argument together with the associated code.
Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Make this const as it not modified in the file referencing it. It is only
stored in a const field 'type' of a device structure. Also, add const to
the variable declaration in the header file.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This PCI host bridge from V3 Semiconductor needs no further
introduction. An ancient driver for it has been sitting in
arch/arm/mach-integrator/pci_v3.* since before v2.6.12 and the
initial migration to git.
But we need to get the drivers out of arch/arm/* and get proper handling of
the old drivers, rewrite and clean up so the PCI maintainer can control the
mass of drivers without having to run all over the kernel. We also switch
swiftly to all the new infrastructure found in the PCI hosts as of late.
Some code is preserved so I have added an extensive list of authors in the
top comment section.
This driver probes with the following result:
OF: PCI: host bridge /pciv3@62000000 ranges:
OF: PCI: No bus range found for /pciv3@62000000, using [bus 00-ff]
OF: PCI: IO 0x60000000..0x6000ffff -> 0x00000000
OF: PCI: MEM 0x40000000..0x4fffffff -> 0x40000000
OF: PCI: MEM 0x50000000..0x5fffffff -> 0x50000000
pci-v3-semi 62000000.pciv3: initialized PCI V3 Integrator/AP integration
pci-v3-semi 62000000.pciv3: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
pci_bus 0000:00: root bus resource [mem 0x40000000-0x4fffffff]
pci_bus 0000:00: root bus resource [mem 0x50000000-0x5fffffff pref]
pci-v3-semi 62000000.pciv3: parity error interrupt
pci-v3-semi 62000000.pciv3: master abort error interrupt
pci-v3-semi 62000000.pciv3: PCI target LB->PCI READ abort interrupt
pci-v3-semi 62000000.pciv3: master abort error interrupt
(repeats a few times)
pci 0000:00:09.0: [1011:0024] type 01 class 0x060400
pci-v3-semi 62000000.pciv3: master abort error interrupt
pci-v3-semi 62000000.pciv3: PCI target LB->PCI READ abort interrupt
pci 0000:00:0b.0: [8086:1229] type 00 class 0x020000
pci 0000:00:0b.0: reg 0x10: [mem 0x00000000-0x00000fff pref]
pci 0000:00:0b.0: reg 0x14: [io 0x0000-0x001f]
pci 0000:00:0b.0: reg 0x18: [mem 0x00000000-0x000fffff]
pci 0000:00:0b.0: reg 0x30: [mem 0x00000000-0x000fffff pref]
pci 0000:00:0b.0: supports D1 D2
pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot
pci 0000:00:0c.0: [5333:8811] type 00 class 0x030000
pci 0000:00:0c.0: reg 0x10: [mem 0x00000000-0x03ffffff]
pci 0000:00:0c.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
pci 0000:00:0c.0: vgaarb: VGA device added: decodes=io+mem,owns=io,locks=none
PCI: bus0: Fast back to back transfers disabled
PCI: bus1: Fast back to back transfers enabled
pci 0000:00:0c.0: BAR 0: assigned [mem 0x40000000-0x43ffffff]
pci 0000:00:0b.0: BAR 2: assigned [mem 0x44000000-0x440fffff]
pci 0000:00:0b.0: BAR 6: assigned [mem 0x50000000-0x500fffff pref]
pci 0000:00:0c.0: BAR 6: assigned [mem 0x50100000-0x5010ffff pref]
pci 0000:00:0b.0: BAR 0: assigned [mem 0x50110000-0x50110fff pref]
pci 0000:00:0b.0: BAR 1: assigned [io 0x1000-0x101f]
pci 0000:00:09.0: PCI bridge to [bus 01]
pci 0000:00:0b.0: Firmware left e100 interrupts enabled; disabling
(...)
e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
e100 0000:00:0b.0: enabling device (0146 -> 0147)
e100 0000:00:0b.0 eth0: addr 0x50110000, irq 31, MAC addr 00:08:c7:99:d2:57
> lspci
00:0b.0 Class 0200: 8086:1229
00:09.0 Class 0604: 1011:0024
00:0c.0 Class 0300: 5333:8811
> cat /proc/iomem
40000000-4fffffff : V3 PCI NON-PRE-MEM
40000000-43ffffff : 0000:00:0c.0
44000000-440fffff : 0000:00:0b.0
44000000-440fffff : e100
50000000-5fffffff : V3 PCI PRE-MEM
50000000-500fffff : 0000:00:0b.0
50100000-5010ffff : 0000:00:0c.0
50110000-50110fff : 0000:00:0b.0
50110000-50110fff : e100
61000000-61ffffff : /pciv3@62000000
62000000-6200ffff : /pciv3@62000000
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[bhelgaas: fold in %pR fixes from Arnd Bergmann <arnd@arndb.de>:
http://lkml.kernel.org/r/20171011140224.3770968-1-arnd@arndb.de]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Niklas Cassel