Notice that one member of struct acpi_bus_ops, acpi_op_add, is not
used anywhere any more and the relationship between its remaining
members, acpi_op_match and acpi_op_start, is such that it doesn't
make sense to set the latter without setting the former at the same
time. Therefore, replace struct acpi_bus_ops with new a enum type,
enum acpi_bus_add_type, with three values, ACPI_BUS_ADD_BASIC,
ACPI_BUS_ADD_MATCH, ACPI_BUS_ADD_START, corresponding to
both acpi_op_match and acpi_op_start unset, acpi_op_match set and
acpi_op_start unset, and both acpi_op_match and acpi_op_start set,
respectively.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Split the ACPI namespace scanning for devices into two passes, such
that struct acpi_device objects are registerd in the first pass
without probing ACPI drivers and the drivers are probed against them
directly in the second pass.
There are two main reasons for doing that.
First, the ACPI PCI root bridge driver's .add() routine,
acpi_pci_root_add(), causes struct pci_dev objects to be created for
all PCI devices under the given root bridge. Usually, there are
corresponding ACPI device nodes in the ACPI namespace for some of
those devices and therefore there should be "companion" struct
acpi_device objects to attach those struct pci_dev objects to. These
struct acpi_device objects should exist when the corresponding
struct pci_dev objects are created, but that is only guaranteed
during boot and not during hotplug. This leads to a number of
functional differences between the boot and the hotplug cases which
are not strictly necessary and make the code more complicated.
For example, this forces the ACPI PCI root bridge driver to defer the
registration of the just created struct pci_dev objects and to use a
special .start() callback routine, acpi_pci_root_start(), to make
sure that all of the "companion" struct acpi_device objects will be
present at PCI devices registration time during hotplug.
If those differences can be eliminated, we will be able to
consolidate the boot and hotplug code paths for the enumeration and
registration of PCI devices and to reduce the complexity of that
code quite a bit.
The second reason is that, in general, it should be possible to
resolve conflicts of resources assigned by the BIOS to different
devices represented by ACPI namespace nodes before any drivers bind
to them and before they are attached to "companion" objects
representing physical devices (such as struct pci_dev). However, for
this purpose we first need to enumerate all ACPI device nodes in the
given namespace scope.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Toshi Kani <toshi.kani@hp.com>
* acpi-general: (38 commits)
ACPI / thermal: _TMP and _CRT/_HOT/_PSV/_ACx dependency fix
ACPI: drop unnecessary local variable from acpi_system_write_wakeup_device()
ACPI: Fix logging when no pci_irq is allocated
ACPI: Update Dock hotplug error messages
ACPI: Update Container hotplug error messages
ACPI: Update Memory hotplug error messages
ACPI: Update CPU hotplug error messages
ACPI: Add acpi_handle_<level>() interfaces
ACPI: remove use of __devexit
ACPI / PM: Add Sony Vaio VPCEB1S1E to nonvs blacklist.
ACPI / battery: Correct battery capacity values on Thinkpads
Revert "ACPI / x86: Add quirk for "CheckPoint P-20-00" to not use bridge _CRS_ info"
ACPI: create _SUN sysfs file
ACPI / memhotplug: bind the memory device when the driver is being loaded
ACPI / memhotplug: don't allow to eject the memory device if it is being used
ACPI / memhotplug: free memory device if acpi_memory_enable_device() failed
ACPI / memhotplug: fix memory leak when memory device is unbound from acpi_memhotplug
ACPI / memhotplug: deal with eject request in hotplug queue
ACPI / memory-hotplug: add memory offline code to acpi_memory_device_remove()
ACPI / memory-hotplug: call acpi_bus_trim() to remove memory device
...
Conflicts:
include/linux/acpi.h (two additions at the end of the same file)
Currently we have valid flag to represent if this ACPI device power
state is valid. A device power state is valid does not necessarily
mean we, as OSPM, has a mean to put the device into that power state,
e.g. D3 cold is always a valid power state for any ACPI device, but if
there is no _PS3 or _PRx for this device, we can't really put that
device into D3 cold power state. The same is true for D0 power state.
So here comes the os_accessible flag, which is only set if the device
has provided us the required means to put it into that power state,
e.g. if we have _PS3 or _PRx, we can put the device into D3 cold state
and thus, D3 cold power state's os_accessible flag will be set in this
case.
And a new wrapper inline function is added to be used to check if
firmware has provided us a way to power off the device during runtime.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To avoid adding an ACPI handle pointer to struct device on
architectures that don't use ACPI, or generally when CONFIG_ACPI is
not set, in which cases that pointer is useless, define struct
acpi_dev_node that will contain the handle pointer if CONFIG_ACPI is
set and will be empty otherwise and use it to represent the ACPI
device node field in struct device.
In addition to that define macros for reading and setting the ACPI
handle of a device that don't generate code when CONFIG_ACPI is
unset. Modify the ACPI subsystem to use those macros instead of
referring to the given device's ACPI handle directly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
_SUN method provides the slot unique-ID in the ACPI namespace. And The value
is written in Advanced Configuration and Power Interface Specification as
follows:
"The _SUN value is required to be unique among the slots ofthe same type.
It is also recommended that this number match the slot number printed on
the physical slot whenever possible."
So if we can know the value, we can identify the physical position of the
slot in the system.
The patch creates "sun" file in sysfs for identifying physical position
of the slot.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Reviewed-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With ACPI 5 we are starting to see devices that don't natively support
discovery but can be enumerated with the help of the ACPI namespace.
Typically, these devices can be represented in the Linux device driver
model as platform devices or some serial bus devices, like SPI or I2C
devices.
Since we want to re-use existing drivers for those devices, we need a
way for drivers to specify the ACPI IDs of supported devices, so that
they can be matched against device nodes in the ACPI namespace. To
this end, it is sufficient to add a pointer to an array of supported
ACPI device IDs, that can be provided by the driver, to struct device.
Moreover, things like ACPI power management need to have access to
the ACPI handle of each supported device, because that handle is used
to invoke AML methods associated with the corresponding ACPI device
node. The ACPI handles of devices are now stored in the archdata
member structure of struct device whose definition depends on the
architecture and includes the ACPI handle only on x86 and ia64. Since
the pointer to an array of supported ACPI IDs is added to struct
device_driver in an architecture-independent way, it is logical to
move the ACPI handle from archdata to struct device itself at the same
time. This also makes code more straightforward in some places and
follows the example of Device Trees that have a poiter to struct
device_node in there too.
This changeset is based on Mika Westerberg's work.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Removed lockable in struct acpi_device_flags since it is no
longer used by any code. acpi_bus_hot_remove_device() cannot
use this flag because acpi_bus_trim() frees up its acpi_device
object. Furthermore, the dock driver calls _LCK method without
using this lockable flag.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Reviewed-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit b87b49cd0efd ("ACPI / PM: Move device PM functions related to sleep
states") declared acpi_target_system_state() for CONFIG_PM_SLEEP whereas
it is only defined for CONFIG_ACPI_SLEEP, resulting in the following link
error:
drivers/built-in.o: In function `acpi_pm_device_sleep_wake':
drivers/acpi/device_pm.c:342: undefined reference to `acpi_target_system_state'
drivers/built-in.o: In function `acpi_dev_suspend_late':
drivers/acpi/device_pm.c:501: undefined reference to `acpi_target_system_state'
drivers/built-in.o: In function `acpi_pm_device_sleep_state':
drivers/acpi/device_pm.c:221: undefined reference to `acpi_target_system_state'
Define it only for CONFIG_ACPI_SLEEP and fallback to a dummy definition
for other configs.
[rjw: The problem only occurs for exotic .configs in which
HIBERNATE_CALLBACKS is selected by XEN_SAVE_RESTORE and neither
SUSPEND nor HIBERNATION is set.]
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Introduce helper function returning the target sleep state of the
system and use it to move the remaining device power management
functions from sleep.c to device_pm.c.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If the caller of acpi_bus_set_power() already has a pointer to the
struct acpi_device object corresponding to the device in question, it
doesn't make sense for it to go through acpi_bus_get_device(), which
may be costly, because it involves acquiring the global ACPI
namespace mutex.
For this reason, export the function operating on struct acpi_device
objects used internally by acpi_bus_set_power(), so that it may be
called instead of acpi_bus_set_power() in the above case, and change
its name to acpi_device_set_power().
Additionally, introduce two inline wrappers for checking ACPI PM
capabilities of devices represented by struct acpi_device objects.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Two device wakeup management routines in device_pm.c and sleep.c,
acpi_pm_device_run_wake() and acpi_pm_device_sleep_wake(), take a
device pointer argument and use it to obtain the ACPI handle of the
corresponding ACPI namespace node. That handle is then used to get
the address of the struct acpi_device object corresponding to the
struct device passed as the argument.
Unfortunately, that last operation may be costly, because it involves
taking the global ACPI namespace mutex, so it shouldn't be carried
out too often. However, the callers of those routines usually call
them in a row with acpi_pm_device_sleep_state() which also takes that
mutex for the same reason, so it would be more efficient if they ran
acpi_bus_get_device() themselves to obtain a pointer to the struct
acpi_device object in question and then passed that pointer to the
appropriate PM routines.
To make that possible, split each of the PM routines mentioned above
in two parts, one taking a struct acpi_device pointer argument and
the other implementing the current interface for compatibility.
Additionally, change acpi_pm_device_run_wake() to actually return
an error code if there is an error while setting up runtime remote
wakeup for the device.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI function for choosing device power state is now located
in drivers/acpi/sleep.c, but drivers/acpi/device_pm.c is a more
logical place for it, so move it there.
However, instead of moving the function entirely, move its core only
under a different name and with a different list of arguments, so
that it is more flexible, and leave a wrapper around it in the
original location.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPI routines for adding and removing device wakeup notifiers are
currently defined in a PCI-specific file, but they will be necessary
for non-PCI devices too, so move them to a separate file under
drivers/acpi and rename them to indicate their ACPI origins.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The kerneldoc comments for acpi_pm_device_sleep_state(),
acpi_pm_device_run_wake(), and acpi_pm_device_sleep_wake() are
outdated or otherwise inaccurate and/or don't follow the common
kerneldoc patterns, so fix them.
Additionally, notice that acpi_pm_device_run_wake() should be under
CONFIG_PM_RUNTIME rather than under CONFIG_PM_SLEEP, so fix that too.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add support to export the device description obtained from the ACPI _STR
method, if one exists for a device, to user-space via a sysfs interface.
This new interface provides a standard and platform neutral way for users
to obtain the description text stored in the ACPI _STR method. If no
_STR method exists for the device, no sysfs 'description' file will be
created. The 'description' file will be located in the /sys/devices/
directory using the device's path.
/sys/device/<bus>/<bridge path>/<device path>.../firmware_node/description
Example:
/sys/devices/pci0000:00/0000:00.07.0/0000:0e:00.0/firmware_node/description
It can also be located using the ACPI device path, for example:
/sys/devices/LNXSYSTM:00/device:00/ACPI0004:00/PNP0A08:00/device:13/device:15/description
/sys/devices/LNXSYSTM:00/device:00/ACPI0004:00/ACPI0004:01/ACPI0007:02/description
Execute the 'cat' command on the 'description' file to obtain the
description string for that device.
This patch also includes documentation describing how the new sysfs
interface works
Changes from v1-v2 based on comments by Len Brown and Fengguang Wu
* Removed output "No Description" and leaving a NULL attribute if the
_STR method failed to evaluate.
* In acpi_device_remove_files() removed the redundent check of
dev->pnp.str_obj before calling free. This check triggered a message
from smatch.
Signed-off-by: Lance Ortiz <lance.ortiz@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add a helper macro module_acpi_driver() which reduces the boilerplate code
for ACPI drivers. This is similar what is done for other busses (PCI, SPI,
I2C etc).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
A USB port's position and connectability can't be identified on some boards
via USB hub registers. ACPI _UPC and _PLD can help to resolve this issue
and so it is necessary to bind USB with ACPI. This patch is to allow ACPI
binding with USB-3.0 hub.
Current ACPI only can bind one struct-device to one ACPI device node.
This can not work with USB-3.0 hub, because the USB-3.0 hub has two logical
devices. Each works for USB-2.0 and USB-3.0 devices. In the Linux USB subsystem,
those two logical hubs are treated as two seperate devices that have two struct
devices. But in the ACPI DSDT, these two logical hubs share one ACPI device
node. So there is a requirement to bind multi struct-devices to one ACPI
device node. This patch is to resolve such problem.
Following is the ACPI device nodes' description under xhci hcd.
Device (XHC)
Device (RHUB)
Device (HSP1)
Device (HSP2)
Device (HSP3)
Device (HSP4)
Device (SSP1)
Device (SSP2)
Device (SSP3)
Device (SSP4)
Topology in the Linux
device XHC
USB-2.0 logical hub USB-3.0 logical hub
HSP1 SSP1
HSP2 SSP2
HSP3 SSP3
HSP4 SSP4
This patch also modifies the output of /proc/acpi/wakeup. One ACPI node
can be associated with multiple devices:
XHC S4 *enabled pci:0000:00:14.0
RHUB S0 disabled usb:usb1
disabled usb:usb2
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch is on top of the ACPICA 20120816 release, which implemented
a native way to decode PLD buffer, so use it instead of leting upper
level users do the decoding.
v2: Modify the check for PLD buffer length to reject buffers whose
length < 16
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Pull ACPI & power management update from Len Brown:
"Re-write of the turbostat tool.
lower overhead was necessary for measuring very large system when
they are very idle.
IVB support in intel_idle
It's what I run on my IVB, others should be able to also:-)
ACPICA core update
We have found some bugs due to divergence between Linux and the
upstream ACPICA base. Most of these patches are to reduce that
divergence to reduce the risk of future bugs.
Some cpuidle updates, mostly for non-Intel
More will be coming, as they depend on this part.
Some thermal management changes needed by non-ACPI systems.
Some _OST (OS Status Indication) updates for hot ACPI hot-plug."
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (51 commits)
Thermal: Documentation update
Thermal: Add Hysteresis attributes
Thermal: Make Thermal trip points writeable
ACPI/AC: prevent OOPS on some boxes due to missing check power_supply_register() return value check
tools/power: turbostat: fix large c1% issue
tools/power: turbostat v2 - re-write for efficiency
ACPICA: Update to version 20120711
ACPICA: AcpiSrc: Fix some translation issues for Linux conversion
ACPICA: Update header files copyrights to 2012
ACPICA: Add new ACPI table load/unload external interfaces
ACPICA: Split file: tbxface.c -> tbxfload.c
ACPICA: Add PCC address space to space ID decode function
ACPICA: Fix some comment fields
ACPICA: Table manager: deploy new firmware error/warning interfaces
ACPICA: Add new interfaces for BIOS(firmware) errors and warnings
ACPICA: Split exception code utilities to a new file, utexcep.c
ACPI: acpi_pad: tune round_robin_time
ACPICA: Update to version 20120620
ACPICA: Add support for implicit notify on multiple devices
ACPICA: Update comments; no functional change
...
Host bridge hotplug
- Add MMCONFIG support for hot-added host bridges (Jiang Liu)
Device hotplug
- Move fixups from __init to __devinit (Sebastian Andrzej Siewior)
- Call FINAL fixups for hot-added devices, too (Myron Stowe)
- Factor out generic code for P2P bridge hot-add (Yinghai Lu)
- Remove all functions in a slot, not just those with _EJx (Amos Kong)
Dynamic resource management
- Track bus number allocation (struct resource tree per domain) (Yinghai Lu)
- Make P2P bridge 1K I/O windows work with resource reassignment (Bjorn Helgaas, Yinghai Lu)
- Disable decoding while updating 64-bit BARs (Bjorn Helgaas)
Power management
- Add PCIe runtime D3cold support (Huang Ying)
Virtualization
- Add VFIO infrastructure (ACS, DMA source ID quirks) (Alex Williamson)
- Add quirks for devices with broken INTx masking (Jan Kiszka)
Miscellaneous
- Fix some PCI Express capability version issues (Myron Stowe)
- Factor out some arch code with a weak, generic, pcibios_setup() (Myron Stowe)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=oo/A
-----END PGP SIGNATURE-----
Merge tag 'for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Host bridge hotplug:
- Add MMCONFIG support for hot-added host bridges (Jiang Liu)
Device hotplug:
- Move fixups from __init to __devinit (Sebastian Andrzej Siewior)
- Call FINAL fixups for hot-added devices, too (Myron Stowe)
- Factor out generic code for P2P bridge hot-add (Yinghai Lu)
- Remove all functions in a slot, not just those with _EJx (Amos
Kong)
Dynamic resource management:
- Track bus number allocation (struct resource tree per domain)
(Yinghai Lu)
- Make P2P bridge 1K I/O windows work with resource reassignment
(Bjorn Helgaas, Yinghai Lu)
- Disable decoding while updating 64-bit BARs (Bjorn Helgaas)
Power management:
- Add PCIe runtime D3cold support (Huang Ying)
Virtualization:
- Add VFIO infrastructure (ACS, DMA source ID quirks) (Alex
Williamson)
- Add quirks for devices with broken INTx masking (Jan Kiszka)
Miscellaneous:
- Fix some PCI Express capability version issues (Myron Stowe)
- Factor out some arch code with a weak, generic, pcibios_setup()
(Myron Stowe)"
* tag 'for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (122 commits)
PCI: hotplug: ensure a consistent return value in error case
PCI: fix undefined reference to 'pci_fixup_final_inited'
PCI: build resource code for M68K architecture
PCI: pciehp: remove unused pciehp_get_max_lnk_width(), pciehp_get_cur_lnk_width()
PCI: reorder __pci_assign_resource() (no change)
PCI: fix truncation of resource size to 32 bits
PCI: acpiphp: merge acpiphp_debug and debug
PCI: acpiphp: remove unused res_lock
sparc/PCI: replace pci_cfg_fake_ranges() with pci_read_bridge_bases()
PCI: call final fixups hot-added devices
PCI: move final fixups from __init to __devinit
x86/PCI: move final fixups from __init to __devinit
MIPS/PCI: move final fixups from __init to __devinit
PCI: support sizing P2P bridge I/O windows with 1K granularity
PCI: reimplement P2P bridge 1K I/O windows (Intel P64H2)
PCI: disable MEM decoding while updating 64-bit MEM BARs
PCI: leave MEM and IO decoding disabled during 64-bit BAR sizing, too
PCI: never discard enable/suspend/resume_early/resume fixups
PCI: release temporary reference in __nv_msi_ht_cap_quirk()
PCI: restructure 'pci_do_fixups()'
...
Since the legacy ACPI driver PM callbacks included into
struct acpi_device_ops are not used any more, drop them.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
None of the drivers implementing the ACPI device suspend callback
uses the pm_message_t argument of it, so this argument may be dropped
entirely from that callback. This will simplify switching the ACPI
bus type to PM handling based on struct dev_pm_ops.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* topic/huang-d3cold-v7:
PCI/PM: add PCIe runtime D3cold support
PCI: do not call pci_set_power_state with PCI_D3cold
PCI/PM: add runtime PM support to PCIe port
ACPI/PM: specify lowest allowed state for device sleep state
Lower device sleep state can save more power, but has more exit
latency too. Sometimes, to satisfy some power QoS and other
requirement, we need to constrain the lowest device sleep state.
In this patch, a parameter to specify lowest allowed state for
acpi_pm_device_sleep_state is added. So that the caller can enforce
the constraint via the parameter.
This is needed by PCIe D3cold support, where the lowest power state
allowed may be D3_HOT instead of default D3_COLD.
CC: Len Brown <lenb@kernel.org>
CC: linux-acpi@vger.kernel.org
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch provide MMCONFIG address for PCI host bridges, which will
be used to support host bridge hotplug. It gets MMCONFIG address
by evaluating _CBA method if available.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Changed acpi_bus_hot_remove_device() to support _OST. This function is
also changed to global so that it can be called from hotplug notify
handlers to perform hot-remove operation.
Changed acpi_eject_store(), which is the sysfs eject handler. It checks
eject_pending to see if the request was originated from ACPI eject
notification. If not, it calls _OST(0x103,84,) per Figure 6-37 in ACPI
5.0 spec.
Added eject_pending bit to acpi_device_flags. This bit is set when the
kernel has received an ACPI eject notification, but does not initiate
its hot-remove operation by itself.
Added struct acpi_eject_event. This structure is used to pass extended
information to acpi_bus_hot_remove_device(), which has a single argument
to support asynchronous call
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Added acpi_evaluate_hotplug_opt(). All ACPI hotplug handlers must call
this function when evaluating _OST for hotplug operations. If the
platform does not support _OST, this function returns AE_NOT_FOUND and
has no effect on the platform.
ACPI_HOTPLUG_OST is defined when all relevant ACPI hotplug operations,
such as CPU, memory and container hotplug, are enabled. This assures
consistent behavior among the hotplug operations with regarding the
_OST support. When ACPI_HOTPLUG_OST is not defined, this function is
a no-op.
ACPI PCI hotplug is not enhanced to support _OST at this time since it
is a legacy method being replaced by PCIe native hotplug. _OST support
for ACPI PCI hotplug may be added in future if necessary.
Some platforms may require the OS to support _OST in order to support
ACPI hotplug operations. For example, if a platform has the management
console where user can request a hotplug operation from, this _OST
support would be required for the management console to show the result
of the hotplug request to user.
Added macro definitions of _OST source events and status codes.
Also renamed OSC_SB_CPUHP_OST_SUPPORT to OSC_SB_HOTPLUG_OST_SUPPORT
since this _OSC bit is not specific to CPU hotplug. This bit is
defined in Table 6-147 of ACPI 5.0 as follows.
Bits: 3
Field Name: Insertion / Ejection _OST Processing Support
Definition: This bit is set if OSPM will evaluate the _OST
object defined under a device when processing
insertion and ejection source event codes.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
introduced in Linux-3.5-rc1 by
66886d6f8c
(ACPI: Add stubs for (un)register_acpi_bus_type)
Fix header file warnings when CONFIG_ACPI is not enabled:
include/acpi/acpi_bus.h:443:42: warning: 'struct acpi_bus_type' declared inside parameter list
include/acpi/acpi_bus.h:443:42: warning: its scope is only this definition or declaration, which is probably not
include/acpi/acpi_bus.h:444:44: warning: 'struct acpi_bus_type' declared inside parameter list
Signed-off-by: Len Brown <len.brown@intel.com>
Add a simple helper function to allow drivers to obtain the physical
device location data.
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's unreasonable to have CONFIG_ACPI for these in drivers, so add some
stub functions.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
acpi_dev_run_wake() is a generic function which can be used by
other subsystem too. Rename it to acpi_pm_device_run_wake, to be
consistent with acpi_pm_device_sleep_wake.
Then move it to ACPI core.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Devices may share same list of power resources in _PR0, for example
Device(Dev0)
{
Name (_PR0, Package (0x01)
{
P0PR,
P1PR
})
}
Device(Dev1)
{
Name (_PR0, Package (0x01)
{
P0PR,
P1PR
}
}
Assume Dev0 and Dev1 were runtime suspended.
Then Dev0 is resumed first and it goes into D0 state.
But Dev1 is left in D0_Uninitialised state.
This is wrong. In this case, Dev1 must be resumed too.
In order to hand this case, each power resource maintains a list of
devices which relies on it.
When power resource is ON, it will check if the devices on its list
can be resumed. The device can only be resumed when all the power
resouces of its _PR0 are ON.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Commit 28c2103 added new state ACPI_STATE_D3_COLD, so the device power
states array must be expanded by one also.
v2: Use ACPI_D_STATE_COUNT instead of number 5 for the array size.
Reported-by: Dan Carpenter <error27@gmail.com>
Suggested-by: Oldřich Jedlička <oldium.pro@seznam.cz>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
After redefining CONFIG_PM to depend on (CONFIG_PM_SLEEP ||
CONFIG_PM_RUNTIME) the CONFIG_PM_OPS option is redundant and can be
replaced with CONFIG_PM.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The wakeup.run_wake_count ACPI device field is only used by the PCI
runtime PM code to "protect" devices from being prepared for
generating wakeup signals more than once in a row. However, it
really doesn't provide any protection, because (1) all of the
functions it is supposed to protect use their own reference counters
effectively ensuring that the device will be set up for generating
wakeup signals just once and (2) the PCI runtime PM code uses
wakeup.run_wake_count in a racy way, since nothing prevents
acpi_dev_run_wake() from being called concurrently from two different
threads for the same device.
Remove the wakeup.run_wake_count ACPI device field which is
unnecessary, confusing and used in a wrong way.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The wake_capable ACPI device flag is not necessary, because it is
only used in scan.c for recording the information that _PRW is
present for the given device. That information is only used by
acpi_add_single_object() to decide whether or not to call
acpi_bus_get_wakeup_device_flags(), so the flag may be dropped
if the _PRW check is moved to acpi_bus_get_wakeup_device_flags().
Moreover, acpi_bus_get_wakeup_device_flags() always returns 0,
so it really should be void.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
There are no more users of acpi_bus_get_power(), so it can be
dropped. Moreover, it should be dropped, because it modifies
the device->power.state field of an ACPI device without updating
the reference counters of the device's power resources, which is
wrong.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Use the new function acpi_bus_update_power() for manipulating power
resources used by ACPI fan devices, which allows them to be put into
the right state during initialization and resume. Consequently,
remove the flags.force_power_state field from struct acpi_device,
which is not necessary any more.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Add function acpi_bus_update_power() for reading the actual power
state of an ACPI device and updating its device->power.state field
in such a way that its power resources' reference counters will
remain consistent with that field.
For this purpose introduce __acpi_bus_set_power() setting the
power state of an ACPI device without updating its
device->power.state field and make acpi_bus_set_power() and
acpi_bus_update_power() use it (acpi_bus_set_power() retains the
current behavior for now).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Drop special ACPI wakeup flags, wakeup.state.enabled and
wakeup.flags.always_enabled, that aren't necessary any more after
we've started to use standard device wakeup flags for handling ACPI
wakeup devices.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
There is a number of problems with acpi_pm_device_sleep_state() now.
First, if _S0W is not defined, it prevents devices from being put
into D3 by PCI runtime PM, which shouldn't happen. Second, it
shouldn't use adev->wakeup.state.enabled, because if it's set, it
only means that either the device is permanently enabled to wake up
the system, or that it has been enabled to do that through
/proc/acpi/wakeup. Finally, it should be compiled if CONFIG_PM_SLEEP
is not set, so that PCI runtime PM works correctly in that case.
Fix these problems.
Reported-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
There is the assumption in acpi_pci_osc_control_set() that it is
always sufficient to compare the mask of _OSC control bits to be
requested with the result of an _OSC query where all of the known
control bits have been checked. However, in general, that need not
be the case. For example, if an _OSC feature A depends on an _OSC
feature B and control of A, B plus another _OSC feature C is
requested simultaneously, the BIOS may return A, B, C, while it would
only return C if A and C were requested without B.
That may result in passing a wrong mask of _OSC control bits to an
_OSC control request, in which case the BIOS may only grant control
of a subset of the requested features. Moreover, acpi_pci_run_osc()
will return error code if that happens and the caller of
acpi_pci_osc_control_set() will not know that it's been granted
control of some _OSC features. Consequently, the system will
generally not work as expected.
Apart from this acpi_pci_osc_control_set() always uses the mask
of _OSC control bits returned by the very first invocation of
acpi_pci_query_osc(), but that is done with the second argument
equal to OSC_PCI_SEGMENT_GROUPS_SUPPORT which generally happens
to affect the returned _OSC control bits.
For these reasons, make acpi_pci_osc_control_set() always check if
control of the requested _OSC features will be granted before making
the final control request. As a result, the osc_control_qry and
osc_queried members of struct acpi_pci_root are not necessary any
more, so drop them and remove the remaining code referring to them.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Previously, we only saved the root bus number, i.e., the beginning of the
downstream bus range. We now support IORESOURCE_BUS resources, so this
patch uses that to keep track of both the beginning and the end of the
downstream bus range.
It's important to know both the beginning and the end for supporting _CBA
(see PCI Firmware spec, rev 3.0, sec 4.1.3) and so we know the limits for
any possible PCI bus renumbering (we can't renumber downstream buses to be
outside the bus number range claimed by the host bridge).
It's clear from the spec that the bus range is supposed to be in _CRS, but
if we don't find it there, we'll assume [_BBN - 0xFF] or [0 - 0xFF].
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: replace acpi_integer by u64
ACPICA: Update version to 20100121.
ACPICA: Remove unused uint32_struct type
ACPICA: Disassembler: Remove obsolete "Integer64" field in parse object
ACPICA: Remove obsolete ACPI_INTEGER (acpi_integer) type
ACPICA: Predefined name repair: fix NULL package elements
ACPICA: AcpiGetDevices: Eliminate unnecessary _STA calls
ACPICA: Update all ACPICA copyrights and signons to 2010
ACPICA: Update for new gcc-4 warning options
Although the majority of PCI devices can generate PMEs that in
principle may be used to wake up devices suspended at run time,
platform support is generally necessary to convert PMEs into wake-up
events that can be delivered to the kernel. If ACPI is used for this
purpose, PME signals generated by a PCI device will trigger the ACPI
GPE associated with the device to generate an ACPI wake-up event that
we can set up a handler for, provided that everything is configured
correctly.
Unfortunately, the subset of PCI devices that have GPEs associated
with them is quite limited. The devices without dedicated GPEs have
to rely on the GPEs associated with other devices (in the majority of
cases their upstream bridges and, possibly, the root bridge) to
generate ACPI wake-up events in response to PME signals from them.
Add ACPI platform support for PCI PME wake-up:
o Add a framework making is possible to use ACPI system notify
handlers for run-time PM.
o Add new PCI platform callback ->run_wake() to struct
pci_platform_pm_ops allowing us to enable/disable the platform to
generate wake-up events for given device. Implemet this callback
for the ACPI platform.
o Define ACPI wake-up handlers for PCI devices and PCI root buses and
make the PCI-ACPI binding code register wake-up notifiers for all
PCI devices present in the ACPI tables.
o Add function pci_dev_run_wake() which can be used by PCI drivers to
check if given device is capable of generating wake-up events at
run time.
Developed in cooperation with Matthew Garrett <mjg@redhat.com>.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use the run_wake flag to mark all devices for which run-time wake-up
events may be generated by the platform. Introduce a new wake-up
flag, always_enabled, for marking devices that should be permanently
enabled to generate run-time events. Also, introduce a reference
counter for run-wake devices and a function that will initialize all
of the run-time wake-up fields for given device.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
acpi_integer is now obsolete and removed from the ACPICA code base,
replaced by u64.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Nobody uses acpi_device_uid(), so this patch removes it.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Every acpi_device has at least one ID (if there's no _HID or _CID, we
give it a synthetic or default ID). So there's no longer a need to
check whether an ID exists; we can just use it.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We now keep a single list of IDs that includes both the _HID and any
_CIDs. We no longer need to keep track of whether the device has a _CID.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
There's no need to treat _HID and _CID differently. Keeping them in
a single list makes code that uses the IDs a little simpler because it
can just traverse the list rather than checking "do we have a HID?",
"do we have any CIDs?"
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add acpi_bus_get_status_handle() so we can get the status of a namespace
object before building a struct acpi_device.
This removes a use of "device->flags.dynamic_status", a cached indicator of
whether _STA exists. It seems simpler and more reliable to just evaluate
_STA and catch AE_NOT_FOUND errors.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We can identify the root of the ACPI device tree by the fact that it
has no parent. This is simpler than passing around ACPI_BUS_TYPE_SYSTEM
and will help remove special treatment of the device tree root.
Currently, we add the root by hand with ACPI_BUS_TYPE_SYSTEM. If we
traverse the tree treating the root as just another device and use
acpi_get_type(), the root shows up as ACPI_TYPE_DEVICE.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Most uses of the ACPI bus device_type (ACPI_BUS_TYPE_DEVICE,
ACPI_BUS_TYPE_POWER, etc) are during device initialization, but
we do need it later for notify handler installation, since that
is different for fixed hardware devices vs. namespace devices.
This patch saves the device_type in the acpi_device structure,
so we can check that rather than comparing against the _HID string.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (119 commits)
ACPI: don't pass handle for fixed hardware notifications
ACPI: remove null pointer checks in deferred execution path
ACPI: simplify deferred execution path
acerhdf: additional BIOS versions
acerhdf: convert to dev_pm_ops
acerhdf: fix fan control for AOA150 model
thermal: add missing Kconfig dependency
acpi: switch /proc/acpi/{debug_layer,debug_level} to seq_file
hp-wmi: fix rfkill memory leak on unload
ACPI: remove unnecessary #ifdef CONFIG_DMI
ACPI: linux/acpi.h should not include linux/dmi.h
hwmon driver for ACPI 4.0 power meters
topstar-laptop: add new driver for hotkeys support on Topstar N01
thinkpad_acpi: fix rfkill memory leak on unload
thinkpad-acpi: report brightness events when required
thinkpad-acpi: don't poll by default any of the reserved hotkeys
thinkpad-acpi: Fix procfs hotkey reset command
thinkpad-acpi: deprecate hotkey_bios_mask
thinkpad-acpi: hotkey poll fixes
thinkpad-acpi: be more strict when detecting a ThinkPad
...
fix the following 'make includecheck' warning:
include/acpi/acpi_bus.h: linux/device.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
LKML-Reference: <1247068058.4382.96.camel@ht.satnam>
Acked-by: Len Brown <len.brown@intel.com>
The wakeup.prepared flag is used for marking devices that have the
wake-up power already enabled, so that the wake-up power is not
enabled twice in a row for the same device. This assumes, however,
that device wake-up power will only be enabled once, while the device
is being prepared for a system-wide sleep transition, and the second
attempt is made by acpi_enable_wakeup_device_prep().
With the upcoming PCI wake-up rework this assumption will not hold
any more for PCI bridges and the root bridge whose wake-up power
may be enabled as a result of wake-up enable propagation from other
devices (eg. add-on devices that are not associated with any GPEs).
Thus, there may be many attempts to enable wake-up power on a PCI
bridge or the root bridge during a system power state transition
and it's better to replace wakeup.prepared with a reference counter.
Reviewed-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We can simplify ACPI drivers if we can tell whether a handle is an
ACPI PCI root or not.
Reviewed-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Linux/ACPI core files using internal.h all PREFIX "ACPI: ",
however, not all ACPI drivers use/want it -- and they
should not have to #undef PREFIX to define their own.
Add GPL commment to internal.h while we are there.
This does not change any actual console output,
asside from a whitespace fix.
Signed-off-by: Len Brown <len.brown@intel.com>
Handler was never invoked. Now invoked if/when host node is deleted.
Data object was not automatically deleted when host node was deleted.
Interface to handler had an unused parameter, removed it.
ACPICA BZ 778.
http://acpica.org/bugzilla/show_bug.cgi?id=778
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Completed a major update for the acpi_get_object_info external interface.
Changes include:
- Support for variable, unlimited length HID, UID, and CID strings
- Support Processor objects the same as Devices (HID,UID,CID,ADR,STA, etc.)
- Call the _SxW power methods on behalf of a device object
- Determine if a device is a PCI root bridge
- Change the ACPI_BUFFER parameter to ACPI_DEVICE_INFO.
These changes will require an update to all callers of this interface.
See the ACPICA Programmer Reference for details.
Also, update all invocations of acpi_get_object_info interface
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
No drivers use the .stop method, so remove it.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
System notify events (0x00-0x7f) are common across all device types
and should be handled in Linux/ACPI, not in drivers. However, some
BIOSes use system notify events in device-specific ways that require
the driver to be involved.
This patch adds a ACPI_DRIVER_ALL_NOTIFY_EVENTS driver flag. When a
driver sets this flag and supplies a .notify method, Linux/ACPI calls
the .notify method for ALL notify events on the device, not just the
device-specific (0x80-0xff) events.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_get_pci_dev() is (hopefully) better, and all callers have been
converted, so let's get rid of this duplicated functionality.
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Returns whether an ACPI CA node is a PCI root bridge or not.
This API is generically useful, and shouldn't just be a hotplug function.
The implementation becomes much simpler as well.
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Previously [5], now [8].
sprintf(acpi_device_bid(device), "CPU%X", cpu_id)
now looks better on systems with more than 0xFF processors.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds support for ACPI device driver .notify() methods. If
such a method is present, Linux/ACPI installs a handler for device
notifications (but not for system notifications such as Bus Check,
Device Check, etc). When a device notification occurs, Linux/ACPI
passes it on to the driver's .notify() method.
In most cases, this removes the need for drivers to install their own
handlers for device-specific notifications.
For fixed hardware devices like some power and sleep buttons, there's
no notification value because there's no control method to execute a
Notify opcode. When a fixed hardware device generates an event, we
handle it the same as a regular device notification, except we send
a ACPI_FIXED_HARDWARE_EVENT value. This is outside the normal 0x0-0xff
range used by Notify opcodes.
Several drivers install their own handlers for system Bus Check and
Device Check notifications so they can support hot-plug. This patch
doesn't affect that usage.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
In acpi_bus_ops, only the acpi_op_add and acpi_op_start flags are used,
so remove all the rest.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
No drivers use the .lock and .scan methods, and the Linux/ACPI
code doesn't even provide a way to invoke them, so remove them.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This is a reimplemention of commit
0119509c4f
from Matthew Garrett <mjg59@srcf.ucam.org>
This patch got removed because of a regression: ThinkPads with a
Intel graphics card and an Integrated Graphics Device BIOS implementation
stopped working.
In fact, they only worked because the ACPI device of the discrete, the
wrong one, got used (via int10). So ACPI functions were poking on the wrong
hardware used which is a sever bug.
The next patch provides support for above ThinkPads to be able to
switch brightness via the legacy thinkpad_acpi driver and automatically
detect when to use it.
Original commit message from Matthew Garrett:
Vendors often ship machines with a choice of integrated or discrete
graphics, and use the same DSDT for both. As a result, the ACPI video
module will locate devices that may not exist on this specific platform.
Attempt to determine whether the device exists or not, and abort the
device creation if it doesn't.
http://bugzilla.kernel.org/show_bug.cgi?id=9614
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
As of version 2.0, ACPI can return 64-bit integers. The current
acpi_evaluate_integer only supports 64-bit integers on 64-bit platforms.
Change the argument to take a pointer to an acpi_integer so we support
64-bit integers on all platforms.
lenb: replaced use of "acpi_integer" with "unsigned long long"
lenb: fixed bug in acpi_thermal_trips_update()
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Catch attempts to use of acpi_driver_data on pointers of wrong type.
akpm: rewritten to use proper C typechecking and remove the
"function"-used-as-lvalue thing.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The battery driver already registers notification handler.
To avoid registering notification handler again,
introduce a notifier chain in global system notifier handler
and use it in dock driver.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
So that one of the several config option permutations will build again.
Tested-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* Introduce function acpi_pm_device_sleep_wake() for enabling and
disabling the system wake-up capability of devices that are power
manageable by ACPI.
* Introduce function acpi_bus_can_wakeup() allowing other (dependent)
subsystems to check if ACPI is able to enable the system wake-up
capability of given device.
* Introduce callback .sleep_wake() in struct pci_platform_pm_ops and
for the ACPI PCI 'driver' make it use acpi_pm_device_sleep_wake().
* Introduce callback .can_wakeup() in struct pci_platform_pm_ops and
for the ACPI 'driver' make it use acpi_bus_can_wakeup().
* Move the PME# handlig code out of pci_enable_wake() and split it
into two functions, pci_pme_capable() and pci_pme_active(),
allowing the caller to check if given device is capable of
generating PME# from given power state and to enable/disable the
device's PME# functionality, respectively.
* Modify pci_enable_wake() to use the new ACPI callbacks and the new
PME#-related functions.
* Drop the generic .platform_enable_wakeup() callback that is not
used any more.
* Introduce device_set_wakeup_capable() that will set the
power.can_wakeup flag of given device.
* Rework PCI device PM initialization so that, if given device is
capable of generating wake-up events, either natively through the
PME# mechanism, or with the help of the platform, its
power.can_wakeup flag is set and its power.should_wakeup flag is
unset as appropriate.
* Make ACPI set the power.can_wakeup flag for devices found to be
wake-up capable by it.
* Make the ACPI wake-up code enable/disable GPEs for devices that
have the wakeup.flags.prepared flag set (which means that their
wake-up power has been enabled).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce additional flag 'prepared' in struct acpi_device_wakeup_flags
and use it to prevent devices from being enable/disabled do wake up the
system multiple times in a row (this does not happen currently, but will
be possible after some of the following patches).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce function acpi_bus_power_manageable() allowing other
(dependent) subsystems to check if ACPI is able to power manage given
device. This may be useful, for example, for PCI device power
management.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Get rid of a superfluous acpi_pm_device_sleep_state() parameter. The
only legitimate value of that parameter must be derived from the first
parameter, which is what all the callers already do. (However, this
does not address the fact that ACPI still doesn't set up those flags.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Kernel mode graphics drivers need this ACPI notifier chaine
so that they can get notified upon hotkey events.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Intel menlow driver needs to get the pointer of themal_zone_device
structure of an ACPI thermal zone.
Attach this to each ACPI thermal zone device object.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Thomas Sujith <sujith.thomas@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We don't need a kset here, a simple kobject will do just fine, so
dynamically create the kobject and use it.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
force_power_state was used as a workaround for invalid cached
power state of the device. We do not cache power state, so no need for
workaround.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_bus_generate_event() takes two strings out of passed device object.
SBS needs to supply these strings directly.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
S4 suspend to disk will disable GPE's permanently
because acpi_gpe_sleep_prepare() does not have
a counterpart at resume time. Thus, those devices
became unavailable for wakeup from subsequent
S3 suspend-to-ram.
Here acpi_gpe_sleep_prepare() is removed, and upon suspend
acpi_enable_wakeup_device() gets its functionality.
Upon resume, acpi_disable_wakeup_device() restores the state.
https://bugzilla.novell.com/show_bug.cgi?id=292300
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Schedule /proc/acpi/event for removal in 6 months.
Re-name acpi_bus_generate_event() to acpi_bus_generate_proc_event()
to make sure there is no confusion that it is for /proc/acpi/event only.
Add CONFIG_ACPI_PROC_EVENT to allow removal of /proc/acpi/event.
There is no functional change if CONFIG_ACPI_PROC_EVENT=y
Signed-off-by: Len Brown <len.brown@intel.com>
The previous events patch added a netlink event for every
user of the legacy /proc/acpi/event interface.
However, some users of /proc/acpi/event are really input events,
and they already report their events via the input layer.
Introduce a new interface, acpi_bus_generate_netlink_event(),
which is explicitly called by devices that want to repoprt
events via netlink. This allows the input-like events
to opt-out of generating netlink events. In summary:
events that are sent via netlink:
ac/battery/sbs
thermal
processor
thinkpad_acpi dock/bay
events that are sent via input layer:
button
video hotkey
thinkpad_acpi hotkey
asus_acpi/asus-laptop hotkey
sonypi/sonylaptop
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Introduce CONFIG_SUSPEND representing the ability to enter system sleep
states, such as the ACPI S3 state, and allow the user to choose SUSPEND
and HIBERNATION independently of each other.
Make HOTPLUG_CPU be selected automatically if SUSPEND or HIBERNATION has
been chosen and the kernel is intended for SMP systems.
Also, introduce CONFIG_PM_SLEEP which is automatically selected if
CONFIG_SUSPEND or CONFIG_HIBERNATION is set and use it to select the
code needed for both suspend and hibernation.
The top-level power management headers and the ACPI code related to
suspend and hibernation are modified to use the new definitions (the
changes in drivers/acpi/sleep/main.c are, mostly, moving code to reduce
the number of ifdefs).
There are many other files in which CONFIG_PM can be replaced with
CONFIG_PM_SLEEP or even with CONFIG_SUSPEND, but they can be updated in
the future.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Define standardized HIDs - Rename current acpi_device_id to acpica_device_id
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Based on the David Brownell's patch at
http://marc.info/?l=linux-acpi&m=117873972806360&w=2
updated by: Rafael J. Wysocki <rjw@sisk.pl>
Add a helper routine returning the lowest power (highest number) ACPI device
power state that given device can be in while the system is in the sleep state
indicated by acpi_target_sleep_state .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Upon ACPI events, send an "acpi_event" via Generic Netlink.
This is in addition to /proc/acpi/event, which remains intact for now.
Thanks to Jamal for his great help.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Teach PNPACPI how to hook up its devices to their ACPI nodes, so that
pnpdev->dev.archdata points to the parallel acpi device node. Previously
this only worked for PCI, leaving a notable hole.
Export "acpi_bus_type" so this can work.
Remove some extraneous whitespace.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need to work on cleaning up the relationship between kobjects, ksets and
ktypes. The removal of 'struct subsystem' is the first step of this,
especially as it is not really needed at all.
Thanks to Kay for fixing the bugs in this patch.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some of the ACPI devices use the internal fake hids
which are exposed to userspace as devces' bus_id after sysfs conversion.
To make it more friendly, we convert them to more understandable strings.
For those devices w/o PNPids, we use "device:instance_no" as the bus_id
instead of "PNPIDNON:instance_no".
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We do this mainly because:
1. hid is used to match ACPI devices and drivers.
.match method which is incompatible to driver model
can be deleted from acpi_driver.ops then.
2. As the .uevent method mark ACPI drivers by PNPID,
fake hid is set to non-PNPID devices so that udev script
can load the right ACPI driver by looking for
"HWID = " or "COMPTID = ".
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add removal_type in structure acpi_device for hot removal.
ACPI_BUS_REMOVAL_EJECT is used for ACPI device hot removal.
Only one parameter is allowed in .remove method due to driver model.
So removal_type is added to indicate different removal type.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add acpi_bus_ops in acpi_device to support acpi hot plug.
NOTE: Two methods .add and .start in acpi_driver.ops are
called separately to probe ACPI devices, while only
.probe method is called in driver model.
As executing .add and .start separately is critical
for ACPI device hot plug, we use acpi_bus_ops to
distinguish different code path.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Setup new sysfs framework
1. Remove /sys/firmware/acpi
2. Add ACPI device in device tree.
File "eject" for every device that has _EJ0 method is moved from
/sys/firmware to /sys/devices.
Operation on this file is exactly the same as before.
i.e. echo 1 to "eject" will cause hot removal of this device.
Corresponding changes should be made in userspace for hot removal.
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Zhang Rui<rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI device/driver registration Interfaces are modified
to follow Linux driver model.
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add ACPI bus_type for Linux driver model.
1. .shutdown method is added into acpi_driver.ops
needed by bus_type operations.
2. remove useless parameter 'int state' in .resume method.
3. change parameter 'int state'
to 'pm_message_t state' in .suspend method.
Note: The new .uevent method mark ACPI drivers by PNPID instead of by name.
Udev script needs to look for "HWID=" or "COMPTID=" to load
ACPI drivers as a result.
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add device_driver into acpi_driver for driver model.
Add helper functions 'to_acpi_device' and 'to_acpi_driver'
to get structure acpi_device/acpi_driver by device/device_driver.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Change ACPI to use dev_archdata instead of firmware_data
This patch changes ACPI to use the new dev_archdata on i386, x86_64
and ia64 (is there any other arch using ACPI ?) to store it's
acpi_handle.
It also removes the firmware_data field from struct device as this
was the only user.
Only build-tested on x86
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit a5e1b94008.
Adrian Bunk points out that it has build errors, and apparently no
maintenance. Throw it out.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Create a driver which lives in the acpi subsystem to handle dock events.
This driver is not an "ACPI" driver, because acpi drivers require that the
object be present when the driver is loaded.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Implemented header file support for the following
additional ACPI tables: ASF!, BOOT, CPEP, DBGP, MCFG, SPCR,
SPMI, TCPA, and WDRT. With this support, all current and
known ACPI tables are now defined in the ACPICA headers and
are available for use by device drivers and other software.
Implemented support to allow tables that contain ACPI
names with invalid characters to be loaded. Previously,
this would cause the table load to fail, but since
there are several known cases of such tables on
existing machines, this change was made to enable
ACPI support for them. Also, this matches the
behavior of the Microsoft ACPI implementation.
https://bugzilla.novell.com/show_bug.cgi?id=147621
Fixed a couple regressions introduced during the memory
optimization in the 20060317 release. The namespace
node definition required additional reorganization and
an internal datatype that had been changed to 8-bit was
restored to 32-bit. (Valery Podrezov)
Fixed a problem where a null pointer passed to
acpi_ut_delete_generic_state() could be passed through
to acpi_os_release_object which is unexpected. Such
null pointers are now trapped and ignored, matching
the behavior of the previous implementation before the
deployment of acpi_os_release_object(). (Valery Podrezov,
Fiodor Suietov)
Fixed a memory mapping leak during the deletion of
a SystemMemory operation region where a cached memory
mapping was not deleted. This became a noticeable problem
for operation regions that are defined within frequently
used control methods. (Dana Meyers)
Reorganized the ACPI table header files into two main
files: one for the ACPI tables consumed by the ACPICA core,
and another for the miscellaneous ACPI tables that are
consumed by the drivers and other software. The various
FADT definitions were merged into one common section and
three different tables (ACPI 1.0, 1.0+, and 2.0)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
updated and tested by Konstantin Karasyov
http://bugzilla.kernel.org/show_bug.cgi?id=5000
Signed-off-by: Patrick Mochel <patrick.mochel@intel.com>
Signed-off-by: Konstantin Karasyov <konstantin.karasyov @intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Nobody looks at the return value, and this brings it into line with
pci_unregister_driver(), etc. Also removed validation of the driver
pointer passed in to register and unregister. More consistent, and we'll
find bugs faster if we fault rather than returning an error that's ignored.
Also makes internal functions acpi_device_unregister() and
acpi_driver_detach() void, since nobody uses their returns either.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Export the acpi_bus_trim function so that the pci hotplug driver can
use it.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implement the framework for binding physical devices
with ACPI devices. A physical bus like PCI bus
should create a 'acpi_bus_type', with:
.find_device:
For device which has parent such as normal PCI devices.
.find_bridge:
It's for special devices, such as PCI root bridge
or IDE controller. Such devices generally haven't a
parent or ->bus. We use the special method
to get an ACPI handle.
Uses new field in struct device: firmware_data
http://bugzilla.kernel.org/show_bug.cgi?id=4277
Signed-off-by: David Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Create new interfaces to recursively add an acpi namespace object to the acpi
device list, and recursively start the namespace object. This is needed for
ACPI based hotplug of a root bridge hierarchy where the add operation must be
performed first and the start operation must be performed separately after the
hot-plugged devices have been properly configured.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!