Add last piece of code to support ST STV0900 dual demodulator.
The IC consist of two dependent parts.
It may use single or dual mode.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The IC consist of two dependent parts.
It may use single or dual mode.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The controller consist of two independent parts.
Every part is similar to LNBP21, but has configurable i2c address.
It is used in NetUP Dual DVB-S2 CI card.
http://linuxtv.org/wiki/index.php/NetUP_Dual_DVB_S2_CI
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tuner is used in NetUP Dual DVB-S2 CI card.
http://linuxtv.org/wiki/index.php/NetUP_Dual_DVB_S2_CI
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
[mchehab@redhat.com: removed a wrong header: "cx23885.h"]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hi there!
While having a look at the allocation of struct dvb_frontend in *_attach
functions, I found some cases calling memset after kzalloc. This is
redundant, and the attached patch removes these calls.
I also changed one case calling kmalloc and memset to kzalloc.
Regards
Matthias
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For i2c normal work, we need to slow down the bus speed. However, the
slow down breaks the eeprom firmware load. So, use normal speed for
eeprom booting and then restore the i2c speed after that.
It should also be noticed that no other I2C transfer should be in course
while booting from eeprom, otherwise, tda10046 goes into an instable
state. So, proper locking are needed at the i2c bus master.
Tested with saa7134 MSI TV @nyware A/D board, that comes with an eeprom
with firmware version 29.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some cards uses cx24116 LNB_DC pin for LNB power control,
some not uses, some uses it different way, like HVR-4000.
Tested-by : Edgar Hucek <gimli@dark-green.com>
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Here is a patch which adds some documentation about meanings of the
the lnbp21 system register bits.
Signed-off-by: Hans Werner <hwerner4@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now there is a card, which uses cx24116 to control LNB DC voltage.
It is DVBWorld DVBS2 PCI-e 2005.
The patch is nedded to add support for that card.
1. Rename CMD_SET_TONEPRE to CMD_LNBDCLEVEL.
2. Fill set_voltage with actually control voltage code.
3. Correct set_tone to not affect voltage.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix this sparse warnings:
drivers/media/dvb/frontends/drx397xD_fw.h:21:2: warning: Using plain integer as NULL pointer
drivers/media/dvb/frontends/drx397xD_fw.h:22:2: warning: Using plain integer as NULL pointer
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
in Hz not kHz, and a comment incorrectly says MHz instead of Hz. I
don't know if this caused real problems anywhere
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
zl10353 i2c-gate was always closed and due to that devices having tuner
behind i2c-gate were broken. Add module configuration which allows disabling
i2c-gate only when really needed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Just like with the s5h1411, the s5h1409 needs a soft-reset in order for it
to know that the tuner has been told to change frequencies. This change
changes the behavior from "random tuning times between 500ms to complete
tuning lock failures" to "tuning lock consistently within 700ms".
Thanks to Robert Krakora <rob.krakora@messagenetsystems.com> for doing
initial testing of the patch on the KWorld 330U.
Thanks to Andy Walls <awalls@radix.net> for doing testing of the patch on
the HVR-1600.
Thanks to Michael Krufky <mkrufky@linuxtv.org> for doing additional testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
anysee.c:44:5: warning: symbol 'dvb_usb_anysee_delsys' was not declared. Should it be static?
cx24116.c:378:3: warning: symbol 'CX24116_MODFEC_MODES' was not declared. Should it be static?
stb0899_algo.c:57:5: warning: symbol 'stb0899_get_srate' was not declared. Should it be static?
stb0899_algo.c:766:6: warning: symbol 'Log2Int' was not declared. Should it be static?
stb0899_drv.c:137:20: warning: symbol 'stb0899_quant_tab' was not declared. Should it be static?
stb0899_drv.c:180:20: warning: symbol 'stb0899_est_tab' was not declared. Should it be static?
stb0899_drv.c:220:5: warning: symbol '_stb0899_read_reg' was not declared. Should it be static?
budget-ci.c:1348:23: warning: symbol 'tt3200_stb6100_config' was not declared. Should it be static?
/home/v4l/master/v4l/cx25840-core.c:190:6: warning: symbol 'cx25840_work_handler' was not declared. Should it be static?
/home/v4l/master/v4l/m5602_s5k83a.c:116:6: warning: symbol 's5k83a_dump_registers' was not declared. Should it be static?
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Report to userspace that cx24116 and stv0899 drivers support DVB-S2.
Signed-off by: Klaus Schmidinger <Klaus.Schmidinger@cadsoft.de>
Acked-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix I2C bridge error in zl10353 if no tunner attached to internal I2C
bus of zl10353 chip.
When set enable bridge from internal I2C bus to the main I2C bus
(saa7134) the main I2C bus stopped very hardly. No any communication. In
our next board we solder additional resistors to internal I2C bus.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Impact: clean up
RW_LOCK_UNLOCKED is deprecated. This patch replaces it with the
__RW_LOCK_UNLOCKED(lock) macro. This change was a little trickier than
others due to the macro being used in another macro that fills an array.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/frontends/af9013.c: In function ‘af9013_set_coeff’:
drivers/media/dvb/frontends/af9013.c:231: warning: ‘ns_coeff2_8k’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c:230: warning: ‘ns_coeff2_2k’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c:229: warning: ‘ns_coeff1_8193nu’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c:228: warning: ‘ns_coeff1_8192nu’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c:227: warning: ‘ns_coeff1_8191nu’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c:226: warning: ‘ns_coeff1_2048nu’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c: In function ‘af9013_update_snr’:
drivers/media/dvb/frontends/af9013.c:1012: warning: ‘snr_table’ may be used uninitialized in this function
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dib7000p.h defines a few extern symbols when CONFIG_DVB_DIB7000P is not set. since the
header is used on more than one driver, this causes symbol duplication, as pointed by
Ingo Molnar <mingo@elte.hu>:
drivers/media/dvb/built-in.o: In function `dib7000p_set_gpio':
(.text+0x3f242): multiple definition of `dib7000p_set_gpio'
drivers/media/video/built-in.o:(.text+0xb8c1e): first defined here
drivers/media/dvb/built-in.o: In function `dib7000p_i2c_enumeration':
(.text+0x3f282): multiple definition of `dib7000p_i2c_enumeration'
drivers/media/video/built-in.o:(.text+0xb8c3e): first defined here
drivers/media/dvb/built-in.o: In function `dib7000p_set_wbd_ref':
(.text+0x3f1c1): multiple definition of `dib7000p_set_wbd_ref'
drivers/media/video/built-in.o:(.text+0xb8bfe): first defined here
LD drivers/net/built-in.o
make[2]: *** [drivers/media/built-in.o] Error 1
Cc: Patrick Boettcher <patrick.boettcher@desy.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Delsys was missing when searching for FEC in table.
This fixes FEC lookup for DVB-S2 QPSK modulation.
Cc: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Uwe Bugla pointed out that there are some more typos in some print-statements. Fixed.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes a typo in cx24113.c.
Signed-off-by: Uwe Bugla <uwe.bugla@gmx.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixed some minor coding style issues and some driver information
printed when using the driver on a board.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This commit adds support for the CX24113 DVB-S tuner driver and thus support for the Technisat Skystar2 revision 2.8.
The driver was created with the help of Technisat. Thank you very much.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Place the s5h1411 into low power mode until first use (to handle the case where
the user plugs in the device and then doesn't use it for a while). On the
Pinnacle 801e, this brings the power usage from 126ma down to 82ma.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently in stb0899 code it appears double .read_status assignment
Send patch to fix it.
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The file(s) below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/media/dvb/frontends/si21xx.c
This patch removes the said #include <version.h>.
Cc: Igor M. Liplianin <liplianin@tut.by>
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Fix a bitfield
- Set gain appropriately
- Slept for the wrong duration
Signed-off-by: Reinhard Nissl <rnissl@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Robert Schlabbach <robert_s@gmx.net> for pointing this out
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Eventhough the delivery system is made standalone, DVBFE_SET_DELSYS
needs to be set as the very first operation, for a multistandard frontend
Splitting delivery system out as a new ioctl, makes things a bit more
easier to understand.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Optimizations galore: Blistering barnacles! The KNC1 and friends
like 90 Mhz clock much better rather than running at a higher
throttle, for almost similar hardware. he exact cause unknown,
possibly due to a lower voltage applied for the demod power supply.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* cut down some I/O operations by disabling "disable gate"
* budget_av was left with the gate open, thereby more susceptible
to RF interference due to I/O operations
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* Better readability
* Avoids duplication
Comments from Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Bug: a string which contains 4 digits needs an array
of size 5. The fifth character will hold the terminating '\0'
Signed-off-by: Reinhard Nissl <rnissl@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Optimization: Round the requested value to achieve a
+/-1MHz error instead of +0/-2MHz
Signed-off-by: Reinhard Nissl <rnissl@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Bug #1: The 5 tap equaliser is set to correct simple perturbations
like reflections on the IF cable for DVB-S. In the case of DVB-S2
a more powerful equalizer is used to correct the filter group delay
allowing the bandwidth to be reduced by a factor of 1/3
Bug #2: The ZIF tuner takes badwidth to be set in Hz
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note:
* At High Symbol Rates we do not have enouph machine cycles to handle the
incoming symbols and hence might run into problems at the very end of the
specified definition
* Most of the equations have been calculated for a master clock of 99 MHz,
running at 90MHz, raises lot of issues such as the need to recalculate
all of them , which is eventually very painful.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Marko Schluessler <marco@lordzodiac.de> for pointing it out
Signed-off-by: Marko Schluessler <marco@lordzodiac.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Bug was found by Arvo Jarve <arvo@softshark.ee>
It was a wonder how it worked in the case with this bug,
STM verified this that this nibble was in fact insignificant
and can be ignored.
But still we need to fix all inconsistencies.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In this case, we will be sure that there exists a carrier
and the center frequency would be simply f1 - f2. In such
a circumstance, the TR loop is simplified to doing a simple
check for timing, rather than searching for the same.
Signed-off-by: Arvo Jarve <arvo@softshark.ee>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
BUG! Setting CRL parameter overwrote the CR Algorithm type,
eventually leading to wrong search algorithm to be employed in
the DVB-S carrier loop optimization.
Symptom: Once the CR optimization stage is passed either way, in
a successful or failed manner, the very next carrier search will
fail, due to no Carrier Search Algorithm specified.
Signed-off-by: Arvo Jarve <arvo@softshark.ee>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Marko Schluessler <marco@lordzodiac.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* Saves 70 mS LOCK time on the STB6100 based
* Saves 100 mS LOCK time on the TDA8261 based
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
which should have happenend in the DVB-S2 mode only, but reading it as it is
for the other delivery systems causes nothing to say but LOCK_LOST, which
just causes confusion amongst users.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We need to check for tuner LOCK LOSS, especially in the case of simple PLL's
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* Reduces szapping time a lot
* increased stability at Low Symbol rates
* overall increases reliability in tuning
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a racy situation.
Inversion is default OFF on the TT S2 3200 hardware,
unlike the KNC1 where it is default Inverted
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use an enumeration for I/Q Swap rather than an int,
easier to spot the nasty ones
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 2 callbacks created nothing more than confusion
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix bug obviously, some enhancements as well
* enable i2c_gate before doing any transaction
* read is one single message with 2 words
* reduce sleep from 100mS to 20mS
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Really silly! Disabled all clocks and expected it to run.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add initial support for:
* KNC1 DVB-S2 Plus
* KNC1 DVB-S2 OEM (known as Satelco DVB-S2)
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Marko Schluessler <marco@lordzodiac.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Marko Schluessler <marco@lordzodiac.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Marko Schluessler <marco@lordzodiac.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Marko Schluessler <marco@lordzodiac.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Marko Schluessler <marco@lordzodiac.de> for pointing it out
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Marco Schluessler <marco@lordzodiac.de> for pointing it out
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
not limited in hardware, this causes instabilities at a higher clock due to
issues such as thermal, also the divider wraps around, which causes the
demodulator core to actually run at a lower frequency. This needs to be
empirically tested whether it affects other cards. If found necessary, this
parameter needs to be moved out to the config struct such that it can be made
hardware dependant.
Reducing the CLOCK from 99MHz to 90MHz improved the acquisition time taken on
the KNC1 cards and hence such a change.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Marko Schluessler <marco@lordzodiac.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Power down the s5h1411 demodulator when not in use (on the Pinnacle 801e, this
brings idle power from 123ma down to 84ma).
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Acked-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If we are already at the desired modulation, there is no need to reconfigure
the demod (at a tuning time cost)
Note that this change revealed that although the datasheet says the demod
starts out in VSB-8 mode, the first tuning was failing consistently unless
we went through the work of setting the registers. So add a field to denote
this case so we always do the enable_frontend call, even if the first tuning
request is for VSB-8.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If you instruct the tuner to change frequencies, it can take up to 2500ms to
get a demod lock. By performing a soft reset after the tuning call (which
is consistent with how the Pinnacle 801e Windows driver behaves), you get
a demod lock inside of 300ms
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
s5h1411: Add the #define for an existing supporting I/F
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adding a serialmode function to read/and/or/write the register for safety.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This includes new bit definitions for previously unknown bits.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
s5h1411: Improvements to the default registers
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove warning message during cx88-dvb compilation.
Also fixes double underline in function and struct names.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
| drivers/media/dvb/frontends/cx24116.c:573: warning: passing argument 3 of 'cx24116_writeregN' discards qualifiers from pointer target type
Make the `data' input pointer parameter of cx24116_writeregN() const to
kill the warning.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Christophe divulged the following:
"Since 8PSK (and higher mod) signals are very likely to have pilot symbols,
pilot_auto should start with pilot_on for 8PSK.
And since QPSK signals are unlikely to have pilot, pilot_auto should start
with pilot_off for QPSK.
Without the patch:
QPSK tuning delay: ~100ms
8PSK tuning delay: ~900ms
with patch:
QPSK tuning delay: ~100ms
8PSK tuning delay: ~100ms
"
This patch does as Cristophe asks. In emulated auto-pilot we
choose pilot-on for tuning PSK_8 and pilot-off for
tuning QPSK.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx24116: Change the default SNR units back to percentage by default.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I've retained the older percentage code after discussing this with
Darron Broad, but made the ESNO option default.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
... and cleanup any drivers using them.
I've also removed NBC_QPSK and modified the cx24116 driver to check
the delivery_type also, removing some excess namespace baggage.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for DvbWorld USB cards with STV0288 demodulator.
Those cards use Earda EDS-1547 tuner.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove NULL pointer in stb6000 driver,
as it raises error for DvbWorld USB card.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allow custom inittab for ST STV0288 demodulator,
as it is needed for DvbWorld USB card.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add some sanity checking to data input via S2API to the cx24116 demod.
This patch is valid for both s2-mfe and s2.
It was found when testing KAFFEINE with S2API support that invalid
modulation modes amongst other parameters were being delivered to
the demod. In order to debug this sanity checking has been added.
An example session would involve kaffeine setting QAM_AUTO when
querying DVB-T, then later when trying to tune to DVB-S this
cached value would be presented in error.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Igor M. Liplianin