This reverts commit 9b0a1de3c8.
Aaro writes:
With v3.12-rc4 I can no longer connect to N800 (OMAP2) with USB
(peripheral, g_ether).
According to git bisect this is caused by:
9b0a1de3c8 is the first bad commit
So revert this patch, as Felipe says:
It's unfortunate that tusb6010 is so messed up
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These aren't necessary after switch and if blocks.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I have am335x-evm with one port running in OTG mode. Since commit
fe4cb09 ("usb: musb: gadget: remove hcd initialization") the loaded
gadget does non pop up on the host. All I see is
|usb 4-5: new high-speed USB device number 52 using ehci-pci
|usb 4-5: device descriptor read/64, error -110
Since a later commit 2cc65fe ("usb: musb: add musb_host_setup() and
musb_host_cleanup()) the gadget shows up on the host again but only
in OTG mode (because we have the host init code running). It does not
work in device only mode.
If running in OTG mode and the gadget is removed and added back (rmmod
followed by modprobe of a gadget) then the same error is pops up on the
host side.
This patch ensures that the gadget side also executes musb_start() which
puts the chip in "connect accept" mode. With this change the device
works in OTG & device mode and the gadget can be added & removed
multiple times.
A device (if musb is in OTG mode acting as a host) is only recognized if
it is attached during module load (musb_hdrc module). After the device
unplugged and plugged again the host does not recognize it. We get a
buch of errors if musb running in OTG mode, attached to a host and no
gadget is loaded. Bah.
This is one step forward. Host & device only mode should work. I will
look at OTG later. I looked at this before commit fe4cb09 and OTG wasn't
working there perfectly so I am not sure that it is a regression :)
Cc: <stable@vger.kernel.org> # v3.11
Cc: Daniel Mack <zonque@gmail.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In gadget mode, musb->is_active should be set only when connected to the
host. musb_g_reset() already takes care of it.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Right after the musb_hdrc driver is loaded, the otg default state
is a_idle, and Mode=Host, which are set by musb_host_setup().
This causes the following kernel message during musb gadget
enumeration.
CAUTION: musb: Babble Interrupt Occurred
This patch sets the otg default state to b_idle, and its Mode to
Peripheral.
It has been validated on TI AM335x GP EVM USB0 port with g_zero.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
musb_shutdown() removes always USB host and device.
musb_init_controller() adds host and device depending on port_mode. If
port mode is set to HOST then the removal of UDC leads only to:
|(NULL device *): gadget not registered.
and nothing else happens. If port mode is set to DEVICE and we remove
the host then we oops in usb_remove_hcd().
This patch ensures that we only remove host in OTG/host mode and device
only in OTG/device mode to avoid any trouble.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since commit 511f3c53 (usb: gadget: udc-core: fix a regression during
gadget driver unbinding) usb_gadget_remove_driver will pass NULL for
the driver argument.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since dma_map_single() may fail it is good to actually check the return
code to see if it succeeded.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch makes use of the two function is_cppi_enabled() and
tusb_dma_omap() instead of the ifdef for the proper DMA implementation
setup code. It basically shifts the code right by one indention level
and adds a few line breaks once the chars are crossed.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If the descriptor is missing the reqeust is never unmapped. This patch
changes this and renames the cleanup label to unlock since there is no
cleanup done. The cleanup would revert the allocation of ressource (i.e.
this dma mapping) but it does not, it simply unlocks and returns.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This will be done from a more appropriate location and as it doesn't
work anyway, it can safely be removed before the other changes.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here is the big Gadget & PHY pull request. Many of us have
been really busy lately getting multiple drivers to a better
position.
Since this pull request is so large, I will divide it in sections
so it's easier to grasp what's included.
- cleanups:
. UDC drivers no longer touch gadget->dev, that's now udc-core
responsibility
. Many more UDC drivers converted to usb_gadget_map/unmap_request()
. UDC drivers no longer initialize DMA-related fields from gadget's
device structure
. UDC drivers don't touch gadget.dev.driver directly
. UDC drivers don't assign gadget.dev.release directly
. Removal of some unused DMA_ADDR_INVALID
. Introduction of CONFIG_USB_PHY
. All phy drivers have been moved to drivers/usb/phy and renamed to
a common naming scheme
. Fix PHY layer so it never returns a NULL pointer, also fix all
callers to avoid using IS_ERR_OR_NULL()
. Sparse fixes all over the place
. drivers/usb/otg/ has been deleted
. Marvel drivers (mv_udc, ehci-mv, mv_otg and mv_u3d) improved clock
usage
- new features:
. UDC core now provides a generic way for tracking and reporting
UDC's state (not attached, resuming, suspended, addressed,
default, etc)
. twl4030-usb learned that it shouldn't be enabled during init
. Full DT support for DWC3 has been implemented
. ab8500-usb learned about pinctrl framework
. nop PHY learned about DeviceTree and regulators
. DWC3 learned about suspend/resume
. DWC3 can now be compiled in host-only and gadget-only (as well as
DRD) configurations
. UVC now enables streaming endpoint based on negotiated speed
. isp1301 now implements the PHY API properly
. configfs-based interface for gadget drivers which will lead to
the removal of all code which just combines functions together
to build functional gadget drivers.
. f_serial and f_obex were converted to new configfs interface while
maintaining old interface around.
- non-critical fixes:
. UVC gadget driver got fixes for Endpoint usage and stream calculation
. ab8500-usb fixed unbalanced clock and regulator API usage
. twl4030-usb got a fix for when OMAP3 is booted with cable connected
. fusb300_udc got a fix for DMA usage
. UVC got fixes for two assertions of the USB Video Class Compliance
specification revision 1.1
. build warning issues caused by recent addition of __must_check to
regulator API
These are all changes which deserve a mention, all other changes are related
to these one or minor spelling fixes and other similar tasks.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=aF4r
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.10 merge window
Here is the big Gadget & PHY pull request. Many of us have
been really busy lately getting multiple drivers to a better
position.
Since this pull request is so large, I will divide it in sections
so it's easier to grasp what's included.
- cleanups:
. UDC drivers no longer touch gadget->dev, that's now udc-core
responsibility
. Many more UDC drivers converted to usb_gadget_map/unmap_request()
. UDC drivers no longer initialize DMA-related fields from gadget's
device structure
. UDC drivers don't touch gadget.dev.driver directly
. UDC drivers don't assign gadget.dev.release directly
. Removal of some unused DMA_ADDR_INVALID
. Introduction of CONFIG_USB_PHY
. All phy drivers have been moved to drivers/usb/phy and renamed to
a common naming scheme
. Fix PHY layer so it never returns a NULL pointer, also fix all
callers to avoid using IS_ERR_OR_NULL()
. Sparse fixes all over the place
. drivers/usb/otg/ has been deleted
. Marvel drivers (mv_udc, ehci-mv, mv_otg and mv_u3d) improved clock
usage
- new features:
. UDC core now provides a generic way for tracking and reporting
UDC's state (not attached, resuming, suspended, addressed,
default, etc)
. twl4030-usb learned that it shouldn't be enabled during init
. Full DT support for DWC3 has been implemented
. ab8500-usb learned about pinctrl framework
. nop PHY learned about DeviceTree and regulators
. DWC3 learned about suspend/resume
. DWC3 can now be compiled in host-only and gadget-only (as well as
DRD) configurations
. UVC now enables streaming endpoint based on negotiated speed
. isp1301 now implements the PHY API properly
. configfs-based interface for gadget drivers which will lead to
the removal of all code which just combines functions together
to build functional gadget drivers.
. f_serial and f_obex were converted to new configfs interface while
maintaining old interface around.
- non-critical fixes:
. UVC gadget driver got fixes for Endpoint usage and stream calculation
. ab8500-usb fixed unbalanced clock and regulator API usage
. twl4030-usb got a fix for when OMAP3 is booted with cable connected
. fusb300_udc got a fix for DMA usage
. UVC got fixes for two assertions of the USB Video Class Compliance
specification revision 1.1
. build warning issues caused by recent addition of __must_check to
regulator API
These are all changes which deserve a mention, all other changes are related
to these one or minor spelling fixes and other similar tasks.
Signed-of-by: Felipe Balbi <balbi@ti.com>
On some platform configurations (like OMAP3+twl4030) it's the platform
code that enables VBUS, not OTG transceiver, so call vbus platform
callback instead, it will then call the transceiver if needed.
This fixes a use case where USB cable is plugged first and gadget
driver is loaded later after that.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some musb glue drivers use gadget_driver pointer to know if any gadget
drivers are loaded at some moment and base further decisions on it,
like to do runtime suspend/resume or not. Right now the pointer is
left alone on stop and OMAP musb glue later does wrong runtime_pm
decisions because of it.
Clear the gadget_driver pointer on remove, it's invalid after stop
anyway.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
all other functions under drivers/usb/ start
with usb_, let's do the same thing.
This patch is in preparation for moving otg_state_string
to usb-common.c and deleting otg.c completely.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix the following compile warning:
drivers/usb/musb/musb_gadget.c: In function ‘rxstate’:
drivers/usb/musb/musb_gadget.c:714:22: warning: comparison of distinct pointer types lacks a cast [enabled by default]
Signed-off-by: Felipe Balbi <balbi@ti.com>
Those comments haven't been updated for a long
time, so much that they don't make sense anymore.
Best to remove them.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We don't need the ->register_my_device flag
anymore because all UDC drivers have been
properly converted.
Let's remove every history of it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
musb does not use DMA buffer for ep0 but it uses the same giveback
function *musb_g_giveback* for all endpoints (*musb_g_ep0_giveback* calls
*musb_g_giveback*). So for ep0 case request.dma will be '0'
and will result in kernel OOPS if tried to *unmap_dma_buffer* for requests in
ep0. Fixed it by doing *unmap_dma_buffer* only for valid DMA addr and
checking that musb_ep->dma is valid when unmapping.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The TXMAXP register is not set correctly for full speed bulk case
when the can_bulk_split() is used. Without this PIO transfers will
not take place correctly
The "mult" factor needs to be updated correctly for the
can_bulk_split() case
The AUTOSET bit in the TXCSR is not being set if the "mult"
factor is greater than 0 for the High Bandwidth ISO case.
But the "mult" factor is also greater than 0 in case of Full speed
bulk transfers with the packet splitting in TXMAXP register
Without the AUTOSET the DMA transfers will not progress in mode1
[ balbi@ti.com : add braces to both branches ]
Signed-off-by: supriya karanth <supriya.karanth@stericsson.com>
Signed-off-by: Praveena NADAHALLY <praveen.nadahally@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Olav Kongas <ok@artecdesign.ee>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves a conflict with these files:
drivers/usb/early/ehci-dbgp.c
drivers/usb/host/ehci-ls1x.c
drivers/usb/host/ohci-xls.c
drivers/usb/musb/ux500.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is part of the workaround for AM35x advisory Advisory 1.1.20.
The advisory says that the IPSS bridge can't handle 8 & 16 bit read
access. An 16bit read access to MUSB_INTRTXE results in an 32bit read
access which also reads INTRRX and therefore may lose interrupts.
This patch uses a shadow register of MUSB_INTRTXE so we only perform
write access to it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is part of the workaround for AM35x advisory Advisory 1.1.20.
The advisory says that the IPSS bridge can't handle 8 & 16 bit read
access. An 16bit read access to MUSB_INTRRXE results in an 32bit read
access which also reads INTRUSB and therefore may lose interrupts.
This patch uses a shadow register of MUSB_INTRRXE so we only perform
write access to it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is part of the workaround for AM35x advisory Advisory 1.1.20.
The advisory says that the IPSS bridge can't handle 8 & 16 bit read
access. An 8bit read access to FADDR results in an 32bit read
access which also reads INTRTX and therefore may lose interrupts.
This patch removes any reads to FADDR as they are not really required.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit 4f3e8d263d.
it turns out that current implementation of Mode 1
DMA added a few regressions to some users, so we
need to revert this patch and let author work on
a better version of Mode 1 DMA support.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Do not rely on any hints from gadget drivers and use DMA mode 1
whenever we expect data of at least the endpoint's packet size and
have not yet received a short packet.
The last packet if short is always transferred using DMA mode 0.
This patch fixes USB throughput issues in mass storage mode for
host to device transfers.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is to reduce the overhead of dma programming for zero byte
transmit as same can be done using pio mode.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In rxstate(), improper types are given to 'fifo_count' and 'len' variables, and
these variables are not used in accordance to their names (up to the certain
point), i.e. 'len' to hold the size of a packet in the RX FIFO, and 'fifo_count'
to hold a difference between 'request->length' and 'request->actual'...
Interchange the variables up to the point where their use starts to make sense
again.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Just two patches here:
First we have a fix to disable DMA in case DMA channel
request fails.
Second, there's a fix for situations where the user
kills musb (by rmmod or any other means) while a
transfer is on the fly. In such cases, we could be
led into a NULL pointer dereference due to endpoint
being disabled and endpoint descriptor being NULL.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJP8VRPAAoJEIaOsuA1yqRE4NkP/jVDJ3akrDHtwjh9Ke8xJNNx
VrfNyx2QU3cYZ2XnUVdvqzcOeUErZpiE/RPtgDAvccSQl5oOuBL8Zlikcj+JfjHM
8Xt6TSd/coIyPYqq6HB1k/mG/dwwWmMf7U0Be+CFEwHsWhPPp80RnYXuGFx6XjZU
wg0mV6iYP1AvGBIN+P5NKwN8HAozz+bxvXDbWyBZUCZL+ws5JTVM53fHy92hFSWs
1N3c3fQizQZP3gmpzuJGV4CUigYWtAcyi1cjGjeIlXroioZK8N55chum+HmrJSiZ
kviZ2K0m0Lh3uNiyH7P2g/7skGbTeCURXxUudnlzdIJKVQdrSni5WXBD9Ydzt1sG
fv3+NDifMTPOoctJJs6y4QVDSOJBdOkHSpA7RWg2HbzD2EPODtKNn8Z+t3Sx7gaG
zL78COmTuhpQOAp0qBcQLuL3dZ2Dq4aDlL9NO2+8vlmrYPilFW0jh/DlUKzryGoA
5a3MA8cBrLG9gwpqlRzyanHjZOU5ejkQaFLQc9wiEzn9fZNh6c/rxk3AedGOzykq
Rw8p90jLy2MuSUKgOPihjZbUzRlW71d2Tt8W4lHnzgA24kj/STS8Y+bhlNLfJFHr
iRYDdFzJHByyt7/cyUGS9lPCAFfw7hjyflvsRuOkGxLuKRKTQk4F/PWWYN6LmNjt
7+z/2VrbxxzPCbRsxay4
=4uPD
-----END PGP SIGNATURE-----
Merge tag 'musb-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: musb: patches for v3.6 merge window
Just two patches here:
First we have a fix to disable DMA in case DMA channel
request fails.
Second, there's a fix for situations where the user
kills musb (by rmmod or any other means) while a
transfer is on the fly. In such cases, we could be
led into a NULL pointer dereference due to endpoint
being disabled and endpoint descriptor being NULL.
usb_ep_ops.disable must clear external copy of the endpoint descriptor,
otherwise musb crashes after loading/unloading several gadget modules
in a row:
Unable to handle kernel paging request at virtual address bf013730
pgd = c0004000
[bf013730] *pgd=8f26d811, *pte=00000000, *ppte=00000000
Internal error: Oops: 7 [#1]
Modules linked in: g_cdc [last unloaded: g_file_storage]
CPU: 0 Not tainted (3.2.17 #647)
PC is at musb_gadget_enable+0x4c/0x24c
LR is at _raw_spin_lock_irqsave+0x4c/0x58
[<c027c030>] (musb_gadget_enable+0x4c/0x24c) from [<bf01b760>] (gether_connect+0x3c/0x19c [g_cdc])
[<bf01b760>] (gether_connect+0x3c/0x19c [g_cdc]) from [<bf01ba1c>] (ecm_set_alt+0x15c/0x180 [g_cdc])
[<bf01ba1c>] (ecm_set_alt+0x15c/0x180 [g_cdc]) from [<bf01ecd4>] (composite_setup+0x85c/0xac4 [g_cdc])
[<bf01ecd4>] (composite_setup+0x85c/0xac4 [g_cdc]) from [<c027b744>] (musb_g_ep0_irq+0x844/0x924)
[<c027b744>] (musb_g_ep0_irq+0x844/0x924) from [<c027a97c>] (musb_interrupt+0x79c/0x864)
[<c027a97c>] (musb_interrupt+0x79c/0x864) from [<c027aaa8>] (generic_interrupt+0x64/0x7c)
[<c027aaa8>] (generic_interrupt+0x64/0x7c) from [<c00797cc>] (handle_irq_event_percpu+0x28/0x178)
...
Cc: stable@vger.kernel.org # v3.1+
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
User can trigger disabling of gadget at run time while the
transfers are going on.
Eg: 1: rmmod of musb driver while transfers are going on
Eg: 2: On android doing:
echo 0 > /sys/class/android_usb/android0/enable
While a big file transfer is going on via PTP/MTP.
In such a case, musb_gadget_disable() calls nuke()
but the dma interrupt may still happen for an endpoint since hw
would raise the interrupt in anycase.
This can result in a NULL pointer access crash:
[ 314.030426] PC is at txstate+0x74/0x20c
[ 314.034759] LR is at musb_g_tx+0x140/0x204
[ 314.039489] pc : [<c03506f4>] lr : [<c0350bcc>] psr: 20000193
[ 314.039520] sp : c783bc68 ip : 00000002 fp : c783bc9c
[ 314.052429] r10: 00000018 r9 : 00000000 r8 : 00000200
[ 314.058258] r7 : 00000000 r6 : fc0ab130 r5 : c781a410 r4 : c6caf640
[ 314.065643] r3 : 00000000 r2 : 00000000 r1 : 00000000 r0 : c781a000
[ 315.083251] Backtrace:
[ 315.086242] [<c0350680>] (txstate+0x0/0x20c) from [<c0350bcc>] (musb_g_tx+0x140/0x204)
[ 315.095123] [<c0350a8c>] (musb_g_tx+0x0/0x204) from [<c034eb00>] (musb_dma_completion+0x40/0x54)
[ 315.104980] [<c034eac0>] (musb_dma_completion+0x0/0x54) from [<c0351e6c>] (dma_controller_irq+0x118/0x184)
[ 315.115661] [<c0351d54>] (dma_controller_irq+0x0/0x184) from [<c00d86b8>] (handle_irq_event_percpu+0x54/0x188)
So put protection in code to handle possiblity of getting an interrupt for an
endpoint that might have been already nuked.
Reported-by: Todd Poynor <toddpoynor@google.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There's really no point in having hcd->irq as a
signed integer when we consider the fact that
IRQ 0 means NO_IRQ. In order to avoid confusion,
make hcd->irq unsigned and fix users who were
passing -1 as the IRQ number to usb_add_hcd.
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
splits OTG functionality away from transceivers.
We have known for quite a long time that struct otg_transceiver was
a bad name for the structure, considering transceiver is far from
being OTG-specific (see 4e67185).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WiB6
-----END PGP SIGNATURE-----
Merge tag 'xceiv-for-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
USB: transceiver changes for 3.4
Here we have a big rework done by Heikki Krogerus (thanks) which
splits OTG functionality away from transceivers.
We have known for quite a long time that struct otg_transceiver was
a bad name for the structure, considering transceiver is far from
being OTG-specific (see 4e67185).
This changes the otg functions so that they receive struct
otg instead of struct usb_phy as parameter and
converts all users of these functions to pass the otg member
of their usb_phy.
Includes fixes to IMX code from Sascha Hauer.
[ balbi@ti.com : fixed a compile warning on ehci-mv.c ]
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Li Yang <leoli@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the new usb_phy_* functions with transceiver
operations instead of the old otg functions.
Includes fixes from Sascha Hauer.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Li Yang <leoli@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
musb INDEX register is getting modified/corrupted during temporary
un-locking in a SMP system. Set this register with proper value
after re-acquiring the lock
Scenario:
---------
CPU1 is handling a data transfer completion interrupt received for
the CLASS1 EP
CPU2 is handling a CLASS2 thread which is queuing data to musb for
transfer
Below is the error sequence:
CPU1 | CPU2
--------------------------------------------------------------------
Data transfer completion inter- |
rupt recieved. |
|
musb INDEX reg set to CLASS1 EP |
|
musb LOCK is acquired. |
|
| CLASS2 thread queues data.
|
| CLASS2 thread tries to acquire musb
| LOCK but lock is already taken by
| CLASS1, so CLASS2 thread is
| spinning.
|
From Interrupt Context musb |
giveback function is called |
|
The giveback function releases | CLASS2 thread now acquires LOCK
LOCK |
|
ClASS1 Request's completion cal-| ClASS2 schedules the data transfer and
lback is called | sets the MUSB INDEX to Class2 EP number
|
Interrupt handler for CLASS1 EP |
tries to acquire LOCK and is |
spinning |
|
Interrupt for Class1 EP acquires| Class2 completes the scheduling etc and
the MUSB LOCK | releases the musb LOCK
|
Interrupt for Class1 EP schedul-|
es the next data transfer |
but musb INDEX register is still|
set to CLASS2 EP |
Since the MUSB INDEX register is set to a different endpoint, we
read and modify the wrong registers. Hence data transfer will not
happen properly. This results in unpredictable behavior
So, the MUSB INDEX register is set to proper value again when
interrupt re-acquires the lock
Cc: stable@vger.kernel.org
Signed-off-by: Supriya Karanth <supriya.karanth@stericsson.com>
Signed-off-by: Praveena Nadahally <praveen.nadahally@stericsson.com>
Reviewed-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use struct usb_otg members with OTG specific functions instead
of usb_phy members.
[ balbi@ti.com: added a missing change on musb_gadget.c to avoid
a compile error on a later patch ]
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There's really no point in doing all that
initcall trickery when we can safely let
udev handle module probing for us.
Remove all of that trickery, by moving everybody
to module_init() and making proper use of
platform_device_register() rather than
platform_device_probe().
Tested-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Tested-by: Tasslehoff Kjappfot <tasskjapp@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This commit renames the “speed” field of the usb_gadget_driver
structure to “max_speed”. This is so that to make it more
apparent that the field represents the maximum speed gadget
driver can support.
This also make the field look more like fields with the same
name in usb_gadget and usb_composite_driver structures. All
of those represent the *maximal* speed given entity supports.
After this commit, there are the following fields in various
structures:
* usb_gadget::speed - the current connection speed,
* usb_gadget::max_speed - maximal speed UDC supports,
* usb_gadget_driver::max_speed - maximal speed gadget driver
supports, and
* usb_composite_driver::max_speed - maximal speed composite
gadget supports.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This commit replaces usb_gadget's is_dualspeed field with
a max_speed field.
[ balbi@ti.com : Fixed DWC3 driver ]
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Several UDC drivers had a gadget driver's speed sanity check of the
form of:
driver->speed != USB_SPEED_HIGH
or:
driver->speed != USB_SPEED_HIGH && driver->speed != USB_SPEED_FULL
As more and more gadget drivers support USB SuperSpeed, driver->speed
may be set to USB_SPEED_SUPER and UDC driver should handle such gadget
correctly. The above checks however fail to recognise USB_SPEED_SUPER
as a valid speed.
This commit changes the two checks to:
driver->speed < USB_SPEED_HIGH
or:
driver->speed < USB_SPEED_FULL
respectively.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman