o Set the ethtool_dump flag (=ETH_FW_DUMP_DISABLE) when dump is disabled.
o update driver version to 4.0.80
Signed-off-by: Manish chopra <manish.chopra@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are NETXEN_NIU_MAX_XG_PORTS ports.
Port indexing starts from zero.
Hence we should also return error for 'port == NETXEN_NIU_MAX_XG_PORTS'.
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
There are 'NETXEN_NIU_MAX_GBE_PORTS' GBE ports. Port indexing starts
from zero.
Hence we should also return error for "port == NETXEN_NIU_MAX_GBE_PORTS"
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Conflicts:
net/ipv6/route.c
This deals with a merge conflict between the net-next addition of the
inetpeer network namespace ops, and Thomas Graf's bug fix in
2a0c451ade which makes sure we don't
register /proc/net/ipv6_route before it is actually safe to do so.
Signed-off-by: David S. Miller <davem@davemloft.net>
The adapter->npars[] array has QLCNIC_MAX_PCI_FUNC elements. We
allocate it that way a few lines earlier in the function. So this test
is off by one.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Use correct l3 (ETH_IP or ETH_IPV6)protcol in case
of inband vlan. Because of incorrect protcol type driver
was setting incorrect opcode. This resulted in adapter calculating
checksum incorrectly.
o Updated driver version to 5.0.29
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Linux stack estimates MSS from skb->len or skb_shinfo(skb)->gso_size.
In case of LRO skb->len is aggregate of len of number of packets hence MSS
obtained using skb->len would be incorrect. Incorrect estimation of recv MSS
would lead to delayed acks in some traffic patterns (which sends two or three
packets and wait for ack and only then send remaining packets). This leads to
drop in performance. Hence we need to set gso_size to MSS obtained from firmware.
o This is fixed recently in firmware hence the MSS is obtained based on
capability. If fw is capable of sending the MSS then only driver sets the gso_size.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull trivial updates from Jiri Kosina:
"As usual, it's mostly typo fixes, redundant code elimination and some
documentation updates."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (57 commits)
edac, mips: don't change code that has been removed in edac/mips tree
xtensa: Change mail addresses of Hannes Weiner and Oskar Schirmer
lib: Change mail address of Oskar Schirmer
net: Change mail address of Oskar Schirmer
arm/m68k: Change mail address of Sebastian Hess
i2c: Change mail address of Oskar Schirmer
net: Fix tcp_build_and_update_options comment in struct tcp_sock
atomic64_32.h: fix parameter naming mismatch
Kconfig: replace "--- help ---" with "---help---"
c2port: fix bogus Kconfig "default no"
edac: Fix spelling errors.
qla1280: Remove redundant NULL check before release_firmware() call
remoteproc: remove redundant NULL check before release_firmware()
qla2xxx: Remove redundant NULL check before release_firmware() call.
aic94xx: Get rid of redundant NULL check before release_firmware() call
tehuti: delete redundant NULL check before release_firmware()
qlogic: get rid of a redundant test for NULL before call to release_firmware()
bna: remove redundant NULL test before release_firmware()
tg3: remove redundant NULL test before release_firmware() call
typhoon: get rid of redundant conditional before all to release_firmware()
...
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Linux stack estimates MSS from skb->len or skb_shinfo(skb)->gso_size.
In case of LRO skb->len is aggregate of len of number of packets hence MSS
obtained using skb->len would be incorrect. Incorrect estimation of recv MSS
would lead to delayed acks in some traffic patterns (which sends two or three
packets and wait for ack and only then send remaining packets). This leads to
drop in performance. Hence we need to set gso_size to MSS obtained from firmware.
o This is fixed recently in firmware hence the MSS is obtained based on
capability. If fw is capable of sending the MSS then only driver sets the gso_size.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver queries DIMM information from firmware and accordingly
sets "presence" field of the structure.
"presence" field when set to 0xff denotes invalid flag. And when
set to 0x0 denotes DIMM memory is not present.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o 0x3, 0x7, 0xF, 0x1F, 0x3F, 0x7F and 0xFF are the allowed capture masks.
Signed-off-by: Manish chopra <manish.chopra@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
disable fw dump by default at start up.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since release_firmware() deals gracefully with being passed a NULL
pointer there is no reason to test explicitly before calling the
function.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
o 0x3, 0x7, 0xF, 0x1F, 0x3F, 0x7F and 0xFF are the allowed capture masks.
o Updated driver version to 5.0.28
Signed-off-by: Manish chopra <manish.chopra@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Without failing probe, register netdevice when device is in FAILED state.
o Device will come up with minimum functionality.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- After FW reset, IP addresses need to be reprogrammed to FW for LRO to work. This
was not happening in context reset path. Fixed it here.
- Updated driver version to 5.0.27
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the datatype of "ip_addr" to __be32 as 'ip' should be in
big endian format.
Adapter needs "ip address" in big endian format stored at lower 32bit
of req.word[1]. netxen_config_ipaddr() now receives 'ip' in big endian
format. To satisfy adapter's need, use memcpy() to copy byte by byte
of 'ip' into lower 32bit of req.word[1].
Mac address and serial number of adapter need to be in little endian format.
Change the data type of the related variables to __le32 / __le64 or cast it
explicitly to __le32 / __le64 depending upon the requirement.
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Silence the following warning:
"warn: returning -1 instead of -ENOMEM is sloppy".
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/vmxnet3/vmxnet3_drv.c
Small vmxnet3 conflict with header size bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
In 'ql_adapter_initialize'
the first call for 'spin_unlock_irqrestore()' is with hw_flags = 0,
which is as good as 'spin_unlock_irq()' (unconditional interrupt
enabling). If this is intended, then for better performance
'spin_unlock_irqrestore()' can be replaced with 'spin_unlock_irq()'
and 'spin_lock_irqsave()' can be replaced by 'spin_lock_irq()
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unify return value of .ndo_set_mac_address if the given address
isn't valid. Return -EADDRNOTAVAIL as eth_mac_addr() already does
if is_valid_ether_addr() fails.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
"esize" should be signed because it can be negative here. For example,
when we call it in netxen_parse_md_template(), it could be -1 from the
return value of netxen_md_L2Cache().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replaced deprecating dev_alloc_skb with netdev_alloc_skb in drivers/net/ethernet
- Removed extra skb->dev = dev after netdev_alloc_skb
Signed-off-by: Pradeep A Dalvi <netdev@pradeepdalvi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver was leaking memory when page allocation failures occurs.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
we have copied skb into addr(page), skb->data doesn't contain ip
header information.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Log dump status.
Remove unmatched qlcnic_api_unlock call.
Update version to 5.0.26.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check bits 8-28 of peg_halt status register for firmware abort code.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report valid link statistics when link is down.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When firmware hang is detected, fw should stop sending pause control frames.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Pass adapter->pdev->dev instead of netdev->dev
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Log states of essential registers on firmware hang detection.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the adapter phy link status to the caller.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reading CRB registers(if reqd) before releasing the api lock.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures use dump_stack so emitting an additional
out-of-memory message is an unnecessary duplication.
Remove the allocation failure messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let caller know the result of adding/removing vlan id to/from vlan
filter.
In some drivers I make those functions to just return 0. But in those
where there is able to see if hw setup went correctly, return value is
set appropriately.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When transmiting a fragmented skb, qlge fills a descriptor with the
fragment addresses, after DMA-mapping them. If there are more than eight
fragments, it will use the eighth descriptor as a pointer to an external
list. After mapping this external list, called OAL to a structure
containing more descriptors, it fills it with the extra fragments.
However, considering that systems with pages larger than 8KiB would have
less than 8 fragments, which was true before commit a715dea3c8, it
defined a macro for the OAL size as 0 in those cases.
Now, if a skb with more than 8 fragments (counting skb->data as one
fragment), this would start overwriting the list of addresses already
mapped and would make the driver fail to properly unmap the right
addresses on architectures with pages larger than 8KiB.
Besides that, the list of mappings was one size too small, since it must
have a mapping for the maxinum number of skb fragments plus one for
skb->data and another for the OAL. So, even on architectures with page
sizes 4KiB and 8KiB, a skb with the maximum number of fragments would
make the driver overwrite its counter for the number of mappings, which,
again, would make it fail to unmap the mapped DMA addresses.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per discussion with Ben Hutchings and David Miller, go through and
remove assignments of "N/A" to fw_version in various drivers'
.get_drvinfo routines. While there clean-up some use of bare
constants and such.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: add couple missing conversions in drivers
split unexporting netdev_fix_features()
implemented %pNF
convert sock::sk_route_(no?)caps
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz