Here is the big staging and IIO driver pull request for 4.20-rc1.
There are lots of things here, we ended up adding more lines than
removing, thanks to a large influx of Comedi National Instrument device
support. Someday soon we need to get comedi out of staging...
Other than the comedi drivers, the "big" things here are:
- new iio drivers
- delete dgnc driver (no one used it and no one had the hardware
anymore)
- vbox driver updates and fixes
- erofs fixes
- tons and tons of tiny checkpatch fixes for almost all staging
drivers
All of these have been in linux-next, with the last few happening a bit
"late" due to them getting stuck on my laptop during travel to the
Mantainers summit.
When merging with your tree, there will be 2 merge conflicts, both files
will be simple to resolve, just delete them :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW9bSGA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk5eACfYp73m9tLO22rnBcXJ73bWAYSTOMAn2GEL4Nc
LZBXs8QvvJIwfqmi7ofn
=UWJn
-----END PGP SIGNATURE-----
Merge tag 'staging-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver updates from Greg KH:
"Here is the big staging and IIO driver pull request for 4.20-rc1.
There are lots of things here, we ended up adding more lines than
removing, thanks to a large influx of Comedi National Instrument
device support. Someday soon we need to get comedi out of staging...
Other than the comedi drivers, the "big" things here are:
- new iio drivers
- delete dgnc driver (no one used it and no one had the hardware
anymore)
- vbox driver updates and fixes
- erofs fixes
- tons and tons of tiny checkpatch fixes for almost all staging
drivers
All of these have been in linux-next, with the last few happening a
bit "late" due to them getting stuck on my laptop during travel to the
Mantainers summit"
* tag 'staging-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (690 commits)
staging: gasket: Fix sparse "incorrect type in assignment" warnings.
staging: gasket: remove debug logs for callback invocation
staging: gasket: remove debug logs in page table mapping calls
staging: rtl8188eu: core: Use sizeof(*p) instead of sizeof(struct P) for memory allocation
staging: ks7010: Remove extra blank line
staging: gasket: Remove extra blank line
staging: media: davinci_vpfe: Fix spelling mistake in enum
staging: speakup: Add a pair of braces
staging: wlan-ng: Replace long int with long
staging: MAINTAINERS: remove obsolete IPX staging directory
staging: MAINTAINERS: remove NCP filesystem entry
staging: rtl8188eu: cleanup comparsions to false
staging: gasket: Update device virtual address comment
staging: gasket: sysfs: fix attribute release comment
staging: gasket: apex: fix sysfs_show
staging: gasket: page_table: simplify gasket_components_to_dev_address
staging: gasket: page_table: fix comment in components_to_dev_address
staging: gasket: page table: fixup error path allocating coherent mem
staging: gasket: page_table: rearrange gasket_page_table_entry
staging: gasket: page_table: remove unnecessary PTE status set to free
...
Fix Sparse warnings:
drivers/staging/vboxvideo/vbox_mode.c:309:6: warning:
symbol 'vbox_primary_atomic_disable' was not declared. Should it be static?
drivers/staging/vboxvideo/vbox_mode.c:452:6: warning:
symbol 'vbox_cursor_atomic_disable' was not declared. Should it be static?
Signed-off-by: Craig Kewley <craigkewley@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to unlock before returning on this error path.
Fixes: 35f3288c45 ("staging: vboxvideo: Atomic phase 1: convert cursor to universal plane")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Store fbhelper and afb struct directly in vbox_private and use
drm_fb_helper_fbdev_setup to replace vbox_fbdev_init, note we cannot use
drm_fb_helper_fbdev_teardown since we use a private framebuffer for the
fbdev.
And replace vbox_driver_lastclose with drm_fb_helper_lastclose.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vbox_mode_valid always returns MODE_OK, which is also the default if no
mode_valid callback is defined.
vbox_best_single_encoder chains to drm_encoder_find, the drm-core will
call drm_encoder_find itself if there is no best_encoder call back.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extend our planes atomic_check callbacks to be more thorough by calling
the drm_atomic_helper_check_plane_state helper.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace vbox_crtc_commit and vbox_crtc_disable with
vbox_crtc_atomic_[en|dis]able which are the preferred callbacks for
these for atomic drivers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Atomic modesetting does not use the traditional dpms call backs, instead
we should check crtc_state->active.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Restore page-flip support now that the atomic conversion is complete.
Since the mode parameter to vbox_crtc_set_base_and_mode() now never
is NULL call drm_atomic_crtc_needs_modeset() to check if we need to
check for input-mapping changes, to avoid doing unnecesarry work on
a flip. And hookup the drm_atomic_helper_page_flip helper to implement
the page_flip callback.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the state objects are wired up, we can:
1) Move to the final atomic handlers
2) Wire up atomic set_config helper
3) Switch to drm_mode_config_helper_suspend/resume for suspend/resume
4) Enable atomic modesetting ioctl
This is all done in one commit because doing this piecemeal leads to
an intermediate state which triggers WARN_ONs in the atomic code because
e.g. plane->fb is still being set.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once we are fully atomic plane->fb will always be NULL and we also
should not access things like crtc->enabled and crt->[hw]mode.
Now that we've wired up the state object handlers, we always have a
plane_state and crtc_state so change the code referencing plane->fb and
crtc->* to use the data from the plane_state and crt_state instead.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wire up state object handlers for the crtc-s and the planes, call
drm_mode_config_reset() after creating all the crtc-s and encoders and
remove the legacy drm_helper_disable_unused_functions() call.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use drm_plane_helpers for the primary plane and replace our custom
mode_set callback with drm_helper_crtc_mode_set.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for atomic conversion, let's use the transitional atomic
helpers drm_plane_helper_update/disable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When setting a mode we not only pass the mode to the hypervisor,
but also information on how to map / translate input coordinates
for the emulated USB tablet. This input-mapping may change when
the mode on *another* crtc changes.
This means that sometimes we must do a modeset on other crtc-s then
the one being changed to update the input-mapping. Including crtc-s
which may be disabled inside the guest (shown as a black window
on the host unless closed by the user).
With atomic modesetting the mode-info of disabled crtcs gets zeroed
yet we need it when updating the input-map to avoid resizing the
window as a side effect of a mode_set on another crtc.
This commit adds caching of the mode info into out private vbox_crtc
struct so that we always have the info at hand when we need it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drm_mode_page_flip_ioctl() cannot deal with the in between phase of
the transitioning to atomic modeset support. Once we start using
drm_helper_crtc_mode_set(), we start setting plane->state on the primary
plane. But we are not fully atomic yet so then set both plane-state->fb
and plane->fb.
If both plane-state->fb and plane->fb are set drm_mode_page_flip_ioctl()
gets confused and stops calling drm_framebuffer_get() on the new fb while
still calling drm_framebuffer_put() on the old fb.
The current page_flip implementation expects drm_mode_page_flip_ioctl()
to take care of both and once we switch to drm_atomic_helper_page_flip()
that will expect neither to be done, taking care of both itself.
So for the transition we need to remove page_flip support and then after
the transition is complete and we set DRIVER_ATOMIC in our driver_features,
we can start using drm_atomic_helper_page_flip().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All the encoder_helper_funcs are optional, and even setting the
drm_encoder_helper_funcs vtable itself is optional and may be left out
when not using any of the helper funcs, so lets drop all of this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This cleanups 2 things:
1) The first time we loop over the crtc-s, to compare framebuffers, fb1 may
get set to NULL by the fb1 = CRTC_FB(crtci); statement and then we call
to_vbox_framebuffer() on it. The result of this call is only used for
an address comparison, so we don't end up dereferencing the bad pointer,
but still it is better to not do this.
2) Since we already figure out the first crtc with a fb in the first loop
and store that in fb1, there is no need to loop over the crtc-s again just
to find the first crtc with a fb again.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add vbox_bo_k[un]map helper functions instead of having code directly
poking struct vbox_bo internals.
While touch neighboring code anyways also fix a return -PTR_ERR(info),
which should be return PTR_ERR(info).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We always need to reserve the bo around a pin / unpin, so move the
reservation there.
This allows removing the vbox_fb_[un]pin helpers.
Note this means that we now no longer hold the bo reserved while
k[un]mapping it in vbox_fb.c this is fine as it is not necessary
to hold it reserved for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When vbox_set_up_input_mapping() gets called the first crtc might be
disable and not have a fb at all, triggering a NUL ptr deref at:
vbox->input_mapping_width = CRTC_FB(crtci)->width;
Instead of using the fb from the crtc with id 0, just use the fb from
the first crtc with a fb. This is in the single_framebuffer = true path,
so all crtc-s point to the same fb anyways.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move pin / unpin of fb out of vbox_crtc_set_base_and_mode() so that it can
be used to implement the atomic_update drm_plane_helper_func for the primary
plane.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fbdev compat fb gets pinned into VRAM at creation and then gets pinned
a second time when set as scanout buffer and unpinned when replaced, this
means its pin count never becomes less then 1, so it is always at the same
address and there is no need for the vbox_fbdev_set_base() call.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's expose the primary plane initialization inside the vboxvideo driver
in preparation for universal planes and atomic.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow specifying where to pin the framebuffer bo, so that this helper can
be used from the cursor code too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vbox_pm_resume() is the only caller of vbox_drm_resume(), so squash the
2 functions into 1.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the recommended way to create the drm_device structure,
according to DRM documentation.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fold the driver_load / unload functions into the probe / remove functions
now that we are no longer using the deprecated drm_get_pci_dev() mechanism.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the setup of drm modesetting config from vbox_driver_load() to
vbox_mode_init().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Registering the connector explicitly right after creation is not necessary
for modesetting drivers, because drm_dev_register already takes care of
this on the core side, by calling drm_modeset_register_all.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the unnecessary vbox_bo_unref() helper and directly call ttm_bo_put()
at the single call site.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vboxfb_create_object() wrapper really does nothing more then just
call vbox_gem_create(), so this commit drops it, replacing it with
a direct call to vbox_gem_create().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In vbox_crtc_set_base_and_mode() we update all the crtcs when the
single_framebuffer setting changes, including the one on which
vbox_crtc_set_base_and_mode() was called, so we end up doing
vbox_do_modeset() on it twice. This commit skips the crtc on which
we are updating in the loop to update the other crtcs.
This commit also removes the vbox_set_view() call from the loop,
vbox_set_view() does not depend on the single_framebuffer setting and it
was being called on the passed in crtc parameter and not on the crtci
local iterator value (typo), so it was a no-op already.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The default settings for Linux vms created in VirtualBox allocate only
16M of videomem. When running fullscreen on a 1920x1080 (or bigger) monitor
this is not a lot.
When using GNOME3 on Wayland we have already been seeing out of video
memory errors for a while now. After commit 2408898e3b ("staging:
vboxvideo: Add page-flip support") this has become much worse as now
multiple buffers are used.
There is nothing we can do about there not being enough video-mem, but
we should handle running out of video-mem properly, currently there are
2 problems with this:
1) vbox_crtc_mode_set() does not check if vbox_crtc_mode_set_base() fails
at all and does not properly propagate the oom error.
2) vbox_crtc_do_set_base() unpins the old fb too soon:
2.1) It unpins it before pinning the new fb, so if the pinning of the new
fb fails (which it will when we run out of video-mem), then we also cannot
fall back to the old-fb as it has been already unpinned. We could try to
re-pin it but there is no guarantee that will succeed.
2.2) It unpins it before reprogramming the hardware to scan out from the
new-fb, which could lead to some ugliness where the hw is scanning out the
oldfb while it is being replaced with something else.
Fixing this requires to do things in this order:
1) Pin the new fb
2) Program the hw
3) Unpin the oldfb
This needs to be done for both a mode_set and for a page_flip so this
commit re-writes vbox_crtc_do_set_base() into vbox_crtc_set_base_and_mode()
which does this in the correct order, putting the hardware programming
which was duplicated between the mode_set and page_flip code inside the
new function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 2408898e3b ("staging: vboxvideo: Add page-flip support") only
calls vbox_crtc_do_set_base() on page-flips, but despite that function's
name it only pins the new fb, unpins the old fb and sets
vbox_crtc->fb_offset. It does not program the hardware to scan out at the
new vbox_crtc->fb_offset value.
This was causing only every other frame (assuming page-flipping between 2
buffers) to be shown since we kept scanning out of the old (now unpinned!)
buffer.
This commit fixes this by adding code to vbox_crtc_page_flip() to tell
the hardware to scanout from the new fb_offset.
Fixes: 2408898e3b ("staging: vboxvideo: Add page-flip support")
Cc: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 1daddbc8de ("staging: vboxvideo: Update driver to use
drm_dev_register.") replaced the obsolere drm_get_pci_dev() with
normal pci probe and remove functions.
But the new vbox_pci_probe() is missing a pci_enable_device() call,
causing interrupts to not be delivered. This causes resizes of the
vm window to not get seen by the drm/kms code.
This commit adds the missing pci_enable_device() call, fixing this.
Fixes: 1daddbc8de ("staging: vboxvideo: Update driver to use ...")
Cc: Fabio Rafael da Rosa <fdr@pid42.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was only added for the drm's fbdev emulation support, so that it
would try harder to show the Oops.
Unfortunately this never really worked reliably, and in practice ended
up pushing the real Oops off the screen due to plentyfull locking,
sleep-while-atomic and other issues. So we removed all that support
from the fbdev emulation a while back. Aside: We've also removed the
kgdb support, for similar reasons.
Since it's such a small patch I figured I don't split this up into the
usual 3-phase removal.
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Alexander Kapshuk <alexander.kapshuk@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: David Lechner <david@lechnology.com>
Cc: nouveau@lists.freedesktop.org
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180822085405.10787-1-daniel.vetter@ffwll.ch
The function ttm_bo_put releases a reference to a TTM buffer object. The
function's name is more aligned to the Linux kernel convention of naming
ref-counting function _get and _put.
A call to ttm_bo_unref takes the address of the TTM BO object's pointer and
clears the pointer's value to NULL. This is not necessary in most cases and
sometimes even worked around by the calling code. A call to ttm_bo_put only
releases the reference without clearing the pointer.
The current behaviour of cleaning the pointer is kept in the calling code,
but should be removed if not required in a later patch.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the big staging/iio patches for 4.19-rc1.
Lots of churn here, with tons of cleanups happening in staging drivers,
a removal of an old crypto driver that no one was using (skein), and the
addition of some new IIO drivers. Also added was a "gasket" driver from
Google that needs loads of work and the erofs filesystem.
Even with adding all of the new drivers and a new filesystem, we are
only adding about 1000 lines overall to the kernel linecount, which
shows just how much cleanup happened, and how big the unused crypto
driver was.
All of these have been in the linux-next tree for a while now with no
reported issues.
Note, you will have a merge problem with a device tree IIO file and the
MAINTAINERS file, both resolutions are easy, just take all changed.
There will be a skein file merge issue as well, but that file got
deleted so just drop that.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g+2A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykwGACfQZz3Ncvc7thHkZytxxqQnbx5JpkAn0yV5SvF
yVXG9SA9yCTKVjYczZjZ
=6t/x
-----END PGP SIGNATURE-----
Merge tag 'staging-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO updates from Greg KH:
"Here are the big staging/iio patches for 4.19-rc1.
Lots of churn here, with tons of cleanups happening in staging
drivers, a removal of an old crypto driver that no one was using
(skein), and the addition of some new IIO drivers. Also added was a
"gasket" driver from Google that needs loads of work and the erofs
filesystem.
Even with adding all of the new drivers and a new filesystem, we are
only adding about 1000 lines overall to the kernel linecount, which
shows just how much cleanup happened, and how big the unused crypto
driver was.
All of these have been in the linux-next tree for a while now with no
reported issues"
* tag 'staging-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (903 commits)
staging:rtl8192u: Remove unused macro definitions - Style
staging:rtl8192u: Add spaces around '+' operator - Style
staging:rtl8192u: Remove stale comment - Style
staging: rtl8188eu: remove unused mp_custom_oid.h
staging: fbtft: Add spaces around / - Style
staging: fbtft: Erases some repetitive usage of function name - Style
staging: fbtft: Adjust some empty-line problems - Style
staging: fbtft: Removes one nesting level to help readability - Style
staging: fbtft: Changes gamma table to define.
staging: fbtft: A bit more information on dev_err.
staging: fbtft: Fixes some alignment issues - Style
staging: fbtft: Puts macro arguments in parenthesis to avoid precedence issues - Style
staging: rtl8188eu: remove unused array dB_Invert_Table
staging: rtl8188eu: remove whitespace, add missing blank line
staging: rtl8188eu: use is_multicast_ether_addr in rtw_sta_mgt.c
staging: rtl8188eu: remove whitespace - style
staging: rtl8188eu: cleanup block comment - style
staging: rtl8188eu: use is_multicast_ether_addr in rtl8188eu_xmit.c
staging: rtl8188eu: use is_multicast_ether_addr in recv_linux.c
staging: rtlwifi: refactor rtl_get_tcb_desc
...
Adds crtc page-flip support by passing the new requested framebuffer
to vbox_crtc_do_set_base().
Note there is no attempt to support vblank interrupts, it's not
not known how to do this in VBOX or if it is even possible. Since
this page-flip implementation does not try to sync the page-flip
to vertical blanking, tearing effects are possible.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This modifies vbox_crtc_do_set_base() to take a new framebuffer to
be activated, instead of the existing framebuffer attached to the crtc.
This change allows the function to be given the new framebuffer from
a page-flip request.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The use of load and unload hooks is deprecated. DRM drivers should
use drm_dev_alloc|drm_dev_init and drm_dev_register for initialization
and publishing.
Signed-off-by: Fabio Rafael da Rosa <fdr@pid42.net>
Reviewed-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big staging and IIO driver update for 4.18-rc1.
It was delayed as I wanted to make sure the final driver deletions did
not cause any major merge issues, and all now looks good.
There are a lot of patches here, just over 1000. The diffstat summary
shows the major changes here:
1007 files changed, 16828 insertions(+), 227770 deletions(-)
Because of this, we might be close to shrinking the overall kernel
source code size for two releases in a row.
There was loads of work in this release cycle, primarily:
- tons of ks7010 driver cleanups
- lots of mt7621 driver fixes and cleanups
- most driver cleanups
- wilc1000 fixes and cleanups
- lots and lots of IIO driver cleanups and new additions
- debugfs cleanups for all staging drivers
- lots of other staging driver cleanups and fixes, the shortlog
has the full details.
but the big user-visable things here are the removal of 3 chunks of
code:
- ncpfs and ipx were removed on schedule, no one has cared about
this code since it moved to staging last year, and if it needs
to come back, it can be reverted.
- lustre file system is removed. I've ranted at the lustre
developers about once a year for the past 5 years, with no
real forward progress at all to clean things up and get the
code into the "real" part of the kernel. Given that the
lustre developers continue to work on an external tree and try
to port those changes to the in-kernel tree every once in a
while, this whole thing really really is not working out at
all. So I'm deleting it so that the developers can spend the
time working in their out-of-tree location and get things
cleaned up properly to get merged into the tree correctly at a
later date.
Because of these file removals, you will have merge issues on some of
these files (2 in the ipx code, 1 in the ncpfs code, and 1 in the
atomisp driver). Just delete those files, it's a simple merge :)
All of this has been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWxvjGQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymoEwCbBYnyUl3cwCszIJ3L3/zvUWpmqIgAn1DDsAim
dM4lmKg6HX/JBSV4GAN0
=zdta
-----END PGP SIGNATURE-----
Merge tag 'staging-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO updates from Greg KH:
"Here is the big staging and IIO driver update for 4.18-rc1.
It was delayed as I wanted to make sure the final driver deletions did
not cause any major merge issues, and all now looks good.
There are a lot of patches here, just over 1000. The diffstat summary
shows the major changes here:
1007 files changed, 16828 insertions(+), 227770 deletions(-)
Because of this, we might be close to shrinking the overall kernel
source code size for two releases in a row.
There was loads of work in this release cycle, primarily:
- tons of ks7010 driver cleanups
- lots of mt7621 driver fixes and cleanups
- most driver cleanups
- wilc1000 fixes and cleanups
- lots and lots of IIO driver cleanups and new additions
- debugfs cleanups for all staging drivers
- lots of other staging driver cleanups and fixes, the shortlog has
the full details.
but the big user-visable things here are the removal of 3 chunks of
code:
- ncpfs and ipx were removed on schedule, no one has cared about this
code since it moved to staging last year, and if it needs to come
back, it can be reverted.
- lustre file system is removed.
I've ranted at the lustre developers about once a year for the past
5 years, with no real forward progress at all to clean things up
and get the code into the "real" part of the kernel.
Given that the lustre developers continue to work on an external
tree and try to port those changes to the in-kernel tree every once
in a while, this whole thing really really is not working out at
all. So I'm deleting it so that the developers can spend the time
working in their out-of-tree location and get things cleaned up
properly to get merged into the tree correctly at a later date.
Because of these file removals, you will have merge issues on some of
these files (2 in the ipx code, 1 in the ncpfs code, and 1 in the
atomisp driver). Just delete those files, it's a simple merge :)
All of this has been in linux-next for a while with no reported
problems"
* tag 'staging-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1011 commits)
staging: ipx: delete it from the tree
ncpfs: remove uapi .h files
ncpfs: remove Documentation
ncpfs: remove compat functionality
staging: ncpfs: delete it
staging: lustre: delete the filesystem from the tree.
staging: vc04_services: no need to save the log debufs dentries
staging: vc04_services: vchiq_debugfs_log_entry can be a void *
staging: vc04_services: remove struct vchiq_debugfs_info
staging: vc04_services: move client dbg directory into static variable
staging: vc04_services: remove odd vchiq_debugfs_top() wrapper
staging: vc04_services: no need to check debugfs return values
staging: mt7621-gpio: reorder includes alphabetically
staging: mt7621-gpio: change gc_map to don't use pointers
staging: mt7621-gpio: use GPIOF_DIR_OUT and GPIOF_DIR_IN macros instead of custom values
staging: mt7621-gpio: change 'to_mediatek_gpio' to make just a one line return
staging: mt7621-gpio: dt-bindings: update documentation for #interrupt-cells property
staging: mt7621-gpio: update #interrupt-cells for the gpio node
staging: mt7621-gpio: dt-bindings: complete documentation for the gpio
staging: mt7621-dts: add missing properties to gpio node
...
The method struct drm_connector_helper_funcs::mode_valid is defined
as returning an 'enum drm_mode_status' but the driver implementation
for this method uses an 'int' for it.
Fix this by using 'enum drm_mode_status' in the driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the checkpatch.pl warning:
WARNING: line over 80 characters
+ vbva = (void __force *)vbox->vbva_buffers + i *
VBVA_MIN_BUFFER_SIZE;
Signed-off-by: Daniel Junho <djunho@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vboxvideo doesn't use dev->struct_mutex and therefore has no need to use
gem_free_object.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Michael Thayer <michael.thayer@oracle.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180327082356.24516-1-daniel.vetter@ffwll.ch
Linus Torvalds