* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm:
dm stripe: implement merge method
dm mpath: allow table load with no priority groups
dm mpath: fail message ioctl if specified path is not valid
dm ioctl: add flag to wipe buffers for secure data
dm ioctl: prepare for crypt key wiping
dm crypt: wipe keys string immediately after key is set
dm: add flakey target
dm: fix opening log and cow devices for read only tables
* 'for-2.6.39/core' of git://git.kernel.dk/linux-2.6-block: (65 commits)
Documentation/iostats.txt: bit-size reference etc.
cfq-iosched: removing unnecessary think time checking
cfq-iosched: Don't clear queue stats when preempt.
blk-throttle: Reset group slice when limits are changed
blk-cgroup: Only give unaccounted_time under debug
cfq-iosched: Don't set active queue in preempt
block: fix non-atomic access to genhd inflight structures
block: attempt to merge with existing requests on plug flush
block: NULL dereference on error path in __blkdev_get()
cfq-iosched: Don't update group weights when on service tree
fs: assign sb->s_bdi to default_backing_dev_info if the bdi is going away
block: Require subsystems to explicitly allocate bio_set integrity mempool
jbd2: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
jbd: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
fs: make fsync_buffers_list() plug
mm: make generic_writepages() use plugging
blk-cgroup: Add unaccounted time to timeslice_used.
block: fixup plugging stubs for !CONFIG_BLOCK
block: remove obsolete comments for blkdev_issue_zeroout.
blktrace: Use rq->cmd_flags directly in blk_add_trace_rq.
...
Fix up conflicts in fs/{aio.c,super.c}
Implement a merge function in the striped target.
When the striped target's underlying devices provide a merge_bvec_fn
(like all DM devices do via dm_merge_bvec) it is important to call down
to them when building a biovec that doesn't span a stripe boundary.
Without the merge method, a striped DM device stacked on DM devices
causes bios with a single page to be submitted which results
in unnecessary overhead that hurts performance.
This change really helps filesystems (e.g. XFS and now ext4) which take
care to assemble larger bios. By implementing stripe_merge(), DM and the
stripe target no longer undermine the filesystem's work by only allowing
a single page per bio. Buffered IO sees the biggest improvement
(particularly uncached reads, buffered writes to a lesser degree). This
is especially so for more capable "enterprise" storage LUNs.
The performance improvement has been measured to be ~12-35% -- when a
reasonable chunk_size is used (e.g. 64K) in conjunction with a stripe
count that is a power of 2.
In contrast, the performance penalty is ~5-7% for the pathological worst
case stripe configuration (small chunk_size with a stripe count that is
not a power of 2). The reason for this is that stripe_map_sector() is
now called once for every call to dm_merge_bvec(). stripe_map_sector()
will use slower division if stripe count isn't a power of 2.
Signed-off-by: Mustafa Mesanovic <mume@linux.vnet.ibm.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch adjusts the multipath target to allow a table with both 0
priority groups and 0 for the initial priority group number.
If any mpath device is held open when all paths in the last priority
group have failed, userspace multipathd will attempt to reload the
associated DM table to reflect the fact that the device no longer has
any priority groups. But the reload attempt always failed because the
multipath target did not allow 0 priority groups.
All multipath target messages related to priority group (enable_group,
disable_group, switch_group) will handle a priority group of 0 (will
cause error).
When reloading a multipath table with 0 priority groups, userspace
multipathd must be updated to specify an initial priority group number
of 0 (rather than 1).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: Babu Moger <babu.moger@lsi.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fail the reinstate_path and fail_path message ioctl if the specified
path is not valid.
The message ioctl would succeed for the 'reinistate_path' and
'fail_path' messages even if action was not taken because the
specified device was not a valid path of the multipath device.
Before, when /dev/vdb is not a path of mpathb:
$ dmsetup message mpathb 0 reinstate_path /dev/vdb
$ echo $?
0
After:
$ dmsetup message mpathb 0 reinstate_path /dev/vdb
device-mapper: message ioctl failed: Invalid argument
Command failed
$ echo $?
1
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add DM_SECURE_DATA_FLAG which userspace can use to ensure
that all buffers allocated for dm-ioctl are wiped
immediately after use.
The user buffer is wiped as well (we do not want to keep
and return sensitive data back to userspace if the flag is set).
Wiping is useful for cryptsetup to ensure that the key
is present in memory only in defined places and only
for the time needed.
(For crypt, key can be present in table during load or table
status, wait and message commands).
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Prepare code for implementing buffer wipe flag.
No functional change in this patch.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Always wipe the original copy of the key after processing it
in crypt_set_key().
Signed-off-by: Milan Broz <mbroz@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This target is the same as the linear target except that it returns I/O
errors periodically. It's been found useful in simulating failing
devices for testing purposes.
I needed a dm target to do some failure testing on btrfs's raid code, and
Mike pointed me at this.
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If a table is read-only, also open any log and cow devices it uses read-only.
Previously, even read-only devices were opened read-write internally.
After patch 75f1dc0d07
block: check bdev_read_only() from blkdev_get()
was applied, loading such tables began to fail. The patch
was reverted by e51900f7d3
block: revert block_dev read-only check
but this patch fixes this part of the code to work with the original patch.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
As a preparation for removing ext2 non-atomic bit operations from
asm/bitops.h. This converts ext2 non-atomic bit operations to
little-endian bit operations.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Alasdair Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As a preparation for removing ext2 non-atomic bit operations from
asm/bitops.h. This converts ext2 non-atomic bit operations to
little-endian bit operations.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After the stack plugging introduction, these are called lockless.
Ensure that the counters are updated atomically.
Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (170 commits)
[SCSI] scsi_dh_rdac: Add MD36xxf into device list
[SCSI] scsi_debug: add consecutive medium errors
[SCSI] libsas: fix ata list corruption issue
[SCSI] hpsa: export resettable host attribute
[SCSI] hpsa: move device attributes to avoid forward declarations
[SCSI] scsi_debug: Logical Block Provisioning (SBC3r26)
[SCSI] sd: Logical Block Provisioning update
[SCSI] Include protection operation in SCSI command trace
[SCSI] hpsa: fix incorrect PCI IDs and add two new ones (2nd try)
[SCSI] target: Fix volume size misreporting for volumes > 2TB
[SCSI] bnx2fc: Broadcom FCoE offload driver
[SCSI] fcoe: fix broken fcoe interface reset
[SCSI] fcoe: precedence bug in fcoe_filter_frames()
[SCSI] libfcoe: Remove stale fcoe-netdev entries
[SCSI] libfcoe: Move FCOE_MTU definition from fcoe.h to libfcoe.h
[SCSI] libfc: introduce __fc_fill_fc_hdr that accepts fc_hdr as an argument
[SCSI] fcoe, libfc: initialize EM anchors list and then update npiv EMs
[SCSI] Revert "[SCSI] libfc: fix exchange being deleted when the abort itself is timed out"
[SCSI] libfc: Fixing a memory leak when destroying an interface
[SCSI] megaraid_sas: Version and Changelog update
...
Fix up trivial conflicts due to whitespace differences in
drivers/scsi/libsas/{sas_ata.c,sas_scsi_host.c}
MD and DM create a new bio_set for every metadevice. Each bio_set has an
integrity mempool attached regardless of whether the metadevice is
capable of passing integrity metadata. This is a waste of memory.
Instead we defer the allocation decision to MD and DM since we know at
metadevice creation time whether integrity passthrough is needed or not.
Automatic integrity mempool allocation can then be removed from
bioset_create() and we make an explicit integrity allocation for the
fs_bio_set.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Zdenek Kabelac <zkabelac@redhat.com>
Acked-by: Mike Snitzer <snizer@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1480 commits)
bonding: enable netpoll without checking link status
xfrm: Refcount destination entry on xfrm_lookup
net: introduce rx_handler results and logic around that
bonding: get rid of IFF_SLAVE_INACTIVE netdev->priv_flag
bonding: wrap slave state work
net: get rid of multiple bond-related netdevice->priv_flags
bonding: register slave pointer for rx_handler
be2net: Bump up the version number
be2net: Copyright notice change. Update to Emulex instead of ServerEngines
e1000e: fix kconfig for crc32 dependency
netfilter ebtables: fix xt_AUDIT to work with ebtables
xen network backend driver
bonding: Improve syslog message at device creation time
bonding: Call netif_carrier_off after register_netdevice
bonding: Incorrect TX queue offset
net_sched: fix ip_tos2prio
xfrm: fix __xfrm_route_forward()
be2net: Fix UDP packet detected status in RX compl
Phonet: fix aligned-mode pipe socket buffer header reserve
netxen: support for GbE port settings
...
Fix up conflicts in drivers/staging/brcm80211/brcmsmac/wl_mac80211.c
with the staging updates.
* 'for-2.6.39' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: fix build failure introduced by s/freezeable/freezable/
workqueue: add system_freezeable_wq
rds/ib: use system_wq instead of rds_ib_fmr_wq
net/9p: replace p9_poll_task with a work
net/9p: use system_wq instead of p9_mux_wq
xfs: convert to alloc_workqueue()
reiserfs: make commit_wq use the default concurrency level
ocfs2: use system_wq instead of ocfs2_quota_wq
ext4: convert to alloc_workqueue()
scsi/scsi_tgt_lib: scsi_tgtd isn't used in memory reclaim path
scsi/be2iscsi,qla2xxx: convert to alloc_workqueue()
misc/iwmc3200top: use system_wq instead of dedicated workqueues
i2o: use alloc_workqueue() instead of create_workqueue()
acpi: kacpi*_wq don't need WQ_MEM_RECLAIM
fs/aio: aio_wq isn't used in memory reclaim path
input/tps6507x-ts: use system_wq instead of dedicated workqueue
cpufreq: use system_wq instead of dedicated workqueues
wireless/ipw2x00: use system_wq instead of dedicated workqueues
arm/omap: use system_wq in mailbox
workqueue: use WQ_MEM_RECLAIM instead of WQ_RESCUER
With the plugging now being explicitly controlled by the
submitter, callers need not pass down unplugging hints
to the block layer. If they want to unplug, it's because they
manually plugged on their own - in which case, they should just
unplug at will.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Code has been converted over to the new explicit on-stack plugging,
and delay users have been converted to use the new API for that.
So lets kill off the old plugging along with aops->sync_page().
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Netlink message processing in the kernel is synchronous these days,
capabilities can be checked directly in security_netlink_recv() from
the current process.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Reviewed-by: James Morris <jmorris@namei.org>
[chrisw: update to include pohmelfs and uvesafb]
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert
b821eaa572
and
f3b99be19d
When I wrote the first of these I had a wrong idea about the
lifetime of 'struct block_device'. It can disappear at any time that
the block device is not open if it falls out of the inode cache.
So relying on the 'size' recorded with it to detect when the
device size has changed and so we need to revalidate, is wrong.
Rather, we really do need the 'changed' attribute stored directly in
the mddev and set/tested as appropriate.
Without this patch, a sequence of:
mknod / open / close / unlink
(which can cause a block_device to be created and then destroyed)
will result in a rescan of the partition table and consequence removal
and addition of partitions.
Several of these in a row can get udev racing to create and unlink and
other code can get confused.
With the patch, the rescan is only performed when needed and so there
are no races.
This is suitable for any stable kernel from 2.6.35.
Reported-by: "Wojcik, Krzysztof" <krzysztof.wojcik@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
blk_throtl_exit assumes that ->queue_lock still exists,
so make sure that it does.
To do this, we stop redirecting ->queue_lock to conf->device_lock
and leave it pointing where it is initialised - __queue_lock.
As the blk_plug functions check the ->queue_lock is held, we now
take that spin_lock explicitly around the plug functions. We don't
need the locking, just the warning removal.
This is needed for any kernel with the blk_throtl code, which is
which is 2.6.37 and later.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
'mdp' devices are md devices with preallocated device numbers
for partitions. As such it is possible to mknod and open a partition
before opening the whole device.
this causes md_probe() to be called with a device number of a
partition, which in-turn calls mddev_find with such a number.
However mddev_find expects the number of a 'whole device' and
does the wrong thing with partition numbers.
So add code to mddev_find to remove the 'partition' part of
a device number and just work with the 'whole device'.
This patch addresses https://bugzilla.kernel.org/show_bug.cgi?id=28652
Reported-by: hkmaly@bigfoot.com
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: <stable@kernel.org>
If the desired size of an array is set (via sysfs) before the array is
active (which is the normal sequence), we currrently call set_capacity
immediately.
This means that a subsequent 'open' (as can be caused by some
udev-triggers program) will notice the new size and try to probe for
partitions. However as the array isn't quite ready yet the read will
fail. Then when the array is read, as the size doesn't change again
we don't try to re-probe.
So when setting array size via sysfs, only call set_capacity if the
array is already active.
Signed-off-by: NeilBrown <neilb@suse.de>
Takeover raid1->raid0 not succeded. Kernel message is shown:
"md/raid0:md126: too few disks (1 of 2) - aborting!"
Problem was that we weren't updating ->raid_disks for that
takeover, unlike all the others.
Signed-off-by: Krzysztof Wojcik <krzysztof.wojcik@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
DM now has more information about the nature of the underlying storage
failure. Path failure is avoided if a request failed due to a target
error. Instead the target error is immediately passed up the stack.
Discard requests that fail due to non-target errors may now be retried.
Errors restricted to the path will be retried or returned if no
paths are available, irregarding the no_path_retry setting.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Following symptoms were observed:
1. After raid0->raid10 takeover operation we have array with 2
missing disks.
When we add disk for rebuild, recovery process starts as expected
but it does not finish- it stops at about 90%, md126_resync process
hangs in "D" state.
2. Similar behavior is when we have mounted raid0 array and we
execute takeover to raid10. After this when we try to unmount array-
it causes process umount hangs in "D"
In scenarios above processes hang at the same function- wait_barrier
in raid10.c.
Process waits in macro "wait_event_lock_irq" until the
"!conf->barrier" condition will be true.
In scenarios above it never happens.
Reason was that at the end of level_store, after calling pers->run,
we call mddev_resume. This calls pers->quiesce(mddev, 0) with
RAID10, that calls lower_barrier.
However raise_barrier hadn't been called on that 'conf' yet,
so conf->barrier becomes negative, which is bad.
This patch introduces setting conf->barrier=1 after takeover
operation. It prevents to become barrier negative after call
lower_barrier().
Signed-off-by: Krzysztof Wojcik <krzysztof.wojcik@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
md_make_request was calling bio_sectors() for part_stat_add
after it was calling the make_request function. This is
bad because the make_request function can free the bio and
because the bi_size field can change around.
The fix here was suggested by Jens Axboe. It saves the
sector count before the make_request call. I hit this
with CONFIG_DEBUG_PAGEALLOC turned on while trying to break
his pretty fusionio card.
Cc: <stable@kernel.org>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Activating a spare in an array while resync/recovery is already
happening can lead the that spare being marked in-sync when it isn't
really.
So don't allow the 'slot' to be set (this activating the device)
while resync/recovery is happening.
Signed-off-by: NeilBrown <neilb@suse.de>
There is no need to set this to zero at this point. It will be
set to zero by remove_and_add_spares or at the start of
md_do_sync at the latest.
And setting it to zero before MD_RECOVERY_RUNNING is cleared can
make a 'zero' appear briefly in the 'sync_completed' sysfs attribute
just as resync is finishing.
So simply remove this setting to zero.
Signed-off-by: NeilBrown <neilb@suse.de>
remove_and_add_spares is called in two places where the needs really
are very different.
remove_and_add_spares should not be called on an array which is about
to be reshaped as some extra devices might have been manually added
and that would remove them. However if the array is 'read-auto',
that will currently happen, which is bad.
So in the 'ro != 0' case don't call remove_and_add_spares but simply
remove the failed devices as the comment suggests is needed.
Signed-off-by: NeilBrown <neilb@suse.de>
This patch introduces raid 1 to raid0 takeover operation
in kernel space.
Signed-off-by: Krzysztof Wojcik <krzysztof.wojcik@intel.com>
Signed-off-by: Neil Brown <neilb@nbeee.brown>
This flag is not needed and is used badly.
Devices that are included in a native-metadata array are reserved
exclusively for that array - and currently have AllReserved set.
They all are bd_claimed for the rdev and so cannot be shared.
Devices that are included in external-metadata arrays can be shared
among multiple arrays - providing there is no overlap.
These are bd_claimed for md in general - not for a particular rdev.
When changing the amount of a device that is used in an array we need
to check for overlap. This currently includes a check on AllReserved
So even without overlap, sharing with an AllReserved device is not
allowed.
However the bd_claim usage already precludes sharing with these
devices, so the test on AllReserved is not needed. And in fact it is
wrong.
As this is the only use of AllReserved, simply remove all usage and
definition of AllReserved.
Signed-off-by: NeilBrown <neilb@suse.de>
As spares can be added manually before a reshape starts, we need to
find them all to mark some of them as in_sync.
Previously we would abort looking for spares when we found an
unallocated spare what could not be added to the array (implying there
was no room for new spares). However already-added spares could be
later in the list, so we need to keep searching.
Signed-off-by: NeilBrown <neilb@suse.de>
As spares can be added to the array before the reshape is started,
we need to find and count them when checking there are enough.
The array could have been degraded, so we need to check all devices,
no just those out side of the range of devices in the array before
the reshape.
So instead of checking the index, check the In_sync flag as that
reliably tells if the device is a spare or this purpose.
Signed-off-by: NeilBrown <neilb@suse.de>
There are two consecutive 'if' statements.
if (mddev->delta_disks >= 0)
....
if (mddev->delta_disks > 0)
The code in the second is equally valid if delta_disks == 0, and these
two statements are the only place that 'added_devices' is used.
So make them a single if statement, make added_devices a local
variable, and re-indent it all.
No functional change.
Signed-off-by: NeilBrown <neilb@suse.de>
If we try to update_raid_disks and it fails, we should put
'delta_disks' back to zero. This is important because some code,
such as slot_store, assumes that delta_disks has been validated.
Signed-off-by: NeilBrown <neilb@suse.de>
WQ_RESCUER is now an internal flag and should only be used in the
workqueue implementation proper. Use WQ_MEM_RECLAIM instead.
This doesn't introduce any functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: dm-devel@redhat.com
Cc: Neil Brown <neilb@suse.de>
Commit e09b457b (block: simplify holder symlink handling) incorrectly
assumed that there is only one link at maximum. dm may use multiple
links and expects block layer to track reference count for each link,
which is different from and unrelated to the exclusive device holder
identified by @holder when the device is opened.
Remove the single holder assumption and automatic removal of the link
and revive the per-link reference count tracking. The code
essentially behaves the same as before commit e09b457b sans the
unnecessary kobject reference count dancing.
While at it, note that this facility should not be used by anyone else
than the current ones. Sysfs symlinks shouldn't be abused like this
and the whole thing doesn't belong in the block layer at all.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Milan Broz <mbroz@redhat.com>
Cc: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Neil Brown <neilb@suse.de>
Cc: linux-raid@vger.kernel.org
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm: (32 commits)
dm: raid456 basic support
dm: per target unplug callback support
dm: introduce target callbacks and congestion callback
dm mpath: delay activate_path retry on SCSI_DH_RETRY
dm: remove superfluous irq disablement in dm_request_fn
dm log: use PTR_ERR value instead of ENOMEM
dm snapshot: avoid storing private suspended state
dm snapshot: persistent make metadata_wq multithreaded
dm: use non reentrant workqueues if equivalent
dm: convert workqueues to alloc_ordered
dm stripe: switch from local workqueue to system_wq
dm: dont use flush_scheduled_work
dm snapshot: remove unused dm_snapshot queued_bios_work
dm ioctl: suppress needless warning messages
dm crypt: add loop aes iv generator
dm crypt: add multi key capability
dm crypt: add post iv call to iv generator
dm crypt: use io thread for reads only if mempool exhausted
dm crypt: scale to multiple cpus
dm crypt: simplify compatible table output
...
* 'for-linus' of git://neil.brown.name/md:
md: Fix removal of extra drives when converting RAID6 to RAID5
md: range check slot number when manually adding a spare.
md/raid5: handle manually-added spares in start_reshape.
md: fix sync_completed reporting for very large drives (>2TB)
md: allow suspend_lo and suspend_hi to decrease as well as increase.
md: Don't let implementation detail of curr_resync leak out through sysfs.
md: separate meta and data devs
md-new-param-to_sync_page_io
md-new-param-to-calc_dev_sboffset
md: Be more careful about clearing flags bit in ->recovery
md: md_stop_writes requires mddev_lock.
md/raid5: use sysfs_notify_dirent_safe to avoid NULL pointer
md: Ensure no IO request to get md device before it is properly initialised.
md: Fix single printks with multiple KERN_<level>s
md: fix regression resulting in delays in clearing bits in a bitmap
md: fix regression with re-adding devices to arrays with no metadata
When a RAID6 is converted to a RAID5, the extra drive should
be discarded. However it isn't due to a typo in a comparison.
This bug was introduced in commit e93f68a1fc in 2.6.35-rc4
and is suitable for any -stable since than.
As the extra drive is not removed, the 'degraded' counter is wrong and
so the RAID5 will not respond correctly to a subsequent failure.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
When adding a spare to an active array, we should check the slot
number, but allow it to be larger than raid_disks if a reshape
is being prepared.
Apply the same test when adding a device to an
array-under-construction. It already had most of the test in place,
but not quite all.
Signed-off-by: NeilBrown <neilb@suse.de>
It is possible to manually add spares to specific slots before
starting a reshape.
raid5_start_reshape should recognised this possibility and include
it in the accounting.
Signed-off-by: NeilBrown <neilb@suse.de>
The values exported in the sync_completed file are unsigned long, which
overflows with very large drives, resulting in wrong values reported.
Since sync_completed uses sectors as unit, we'll start getting wrong
values with components larger than 2TB.
This patch simply replaces the use of unsigned long by unsigned long long.
Signed-off-by: Rémi Rérolle <rrerolle@lacie.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The sysfs attributes 'suspend_lo' and 'suspend_hi' describe a region
to which read/writes are suspended so that the under lying data can be
manipulated without user-space noticing.
Currently the window they describe can only move forwards along the
device. However this is an unnecessary restriction which will cause
problems with planned developments.
So relax this restriction and allow these endpoints to move
arbitrarily.
Signed-off-by: NeilBrown <neilb@suse.de>
mddev->curr_resync has artificial values of '1' and '2' which are used
by the code which ensures only one resync is happening at a time on
any given device.
These values are internal and should never be exposed to user-space
(except when translated appropriately as in the 'pending' status in
/proc/mdstat).
Unfortunately they are as ->curr_resync is assigned to
->curr_resync_completed and that value is directly visible through
sysfs.
So change the assignments to ->curr_resync_completed to get the same
valued from elsewhere in a form that doesn't have the magic '1' or '2'
values.
Signed-off-by: NeilBrown <neilb@suse.de>
Allow the metadata to be on a separate device from the
data.
This doesn't mean the data and metadata will by on separate
physical devices - it simply gives device-mapper and userspace
tools more flexibility.
Signed-off-by: NeilBrown <neilb@suse.de>
Add new parameter to 'sync_page_io'.
The new parameter allows us to distinguish between metadata and data
operations. This becomes important later when we add the ability to
use separate devices for data and metadata.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
When we allow for separate devices for data and metadata
in a later patch, we will need to be able to calculate
the superblock offset based on more than the bdev.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Setting ->recovery to 0 is generally not a good idea as it could clear
bits that shouldn't be cleared. In particular, MD_RECOVERY_FROZEN
should only be cleared on explicit request from user-space.
So when we need to clear things, just clear the bits that need
clearing.
As there are a few different places which reap a resync process - and
some do an incomplte job - factor out the code for doing the from
md_check_recovery and call that function instead of open coding part
of it.
Signed-off-by: NeilBrown <neilb@suse.de>
Reported-by: Jonathan Brassow <jbrassow@redhat.com>
As md_stop_writes manipulates the sync_thread and calls md_update_sb,
it need to be called with mddev_lock held.
In all internal cases it is, but the symbol is exported for dm-raid to
call and in that case the lock won't be help.
Do make an exported version which takes the lock, and an internal
version which does not.
Signed-off-by: NeilBrown <neilb@suse.de>
With the module parameter 'start_dirty_degraded' set,
raid5_spare_active() previously called sysfs_notify_dirent() with a NULL
argument (rdev->sysfs_state) when a rebuild finished.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When an md device is in the process of coming on line it is possible
for an IO request (typically a partition table probe) to get through
before the array is fully initialised, which can cause unexpected
behaviour (e.g. a crash).
So explicitly record when the array is ready for IO and don't allow IO
through until then.
There is no possibility for a similar problem when the array is going
off-line as there must only be one 'open' at that time, and it is busy
off-lining the array and so cannot send IO requests. So no memory
barrier is needed in md_stop()
This has been a bug since commit 409c57f380 in 2.6.30 which
introduced md_make_request. Before then, each personality would
register its own make_request_fn when it was ready.
This is suitable for any stable kernel from 2.6.30.y onwards.
Cc: <stable@kernel.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Reported-by: "Hawrylewicz Czarnowski, Przemyslaw" <przemyslaw.hawrylewicz.czarnowski@intel.com>
commit 589a594be1 (2.6.37-rc4) fixed a problem were md_thread would
sometimes call the ->run function at a bad time.
If an error is detected during array start up after the md_thread has
been started, the md_thread is killed. This resulted in the ->run
function being called once. However the array may not be in a state
that it is safe to call ->run.
However the fix imposed meant that ->run was not called on a timeout.
This means that when an array goes idle, bitmap bits do not get
cleared promptly. While the array is busy the bits will still be
cleared when appropriate so this is not very serious. There is no
risk to data.
Change the test so that we only avoid calling ->run when the thread
is being stopped. This more explicitly addresses the problem situation.
This is suitable for 2.6.37-stable and any -stable kernel to which
589a594be1 was applied.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
This patch is the skeleton for the DM target that will be
the bridge from DM to MD (initially RAID456 and later RAID1). It
provides a way to use device-mapper interfaces to the MD RAID456
drivers.
As with all device-mapper targets, the nominal public interfaces are the
constructor (CTR) tables and the status outputs (both STATUSTYPE_INFO
and STATUSTYPE_TABLE). The CTR table looks like the following:
1: <s> <l> raid \
2: <raid_type> <#raid_params> <raid_params> \
3: <#raid_devs> <meta_dev1> <dev1> .. <meta_devN> <devN>
Line 1 contains the standard first three arguments to any device-mapper
target - the start, length, and target type fields. The target type in
this case is "raid".
Line 2 contains the arguments that define the particular raid
type/personality/level, the required arguments for that raid type, and
any optional arguments. Possible raid types include: raid4, raid5_la,
raid5_ls, raid5_rs, raid6_zr, raid6_nr, and raid6_nc. (again, raid1 is
planned for the future.) The list of required and optional parameters
is the same for all the current raid types. The required parameters are
positional, while the optional parameters are given as key/value pairs.
The possible parameters are as follows:
<chunk_size> Chunk size in sectors.
[[no]sync] Force/Prevent RAID initialization
[rebuild <idx>] Rebuild the drive indicated by the index
[daemon_sleep <ms>] Time between bitmap daemon work to clear bits
[min_recovery_rate <kB/sec/disk>] Throttle RAID initialization
[max_recovery_rate <kB/sec/disk>] Throttle RAID initialization
[max_write_behind <value>] See '-write-behind=' (man mdadm)
[stripe_cache <sectors>] Stripe cache size for higher RAIDs
Line 3 contains the list of devices that compose the array in
metadata/data device pairs. If the metadata is stored separately, a '-'
is given for the metadata device position. If a drive has failed or is
missing at creation time, a '-' can be given for both the metadata and
data drives for a given position.
Examples:
# RAID4 - 4 data drives, 1 parity
# No metadata devices specified to hold superblock/bitmap info
# Chunk size of 1MiB
# (Lines separated for easy reading)
0 1960893648 raid \
raid4 1 2048 \
5 - 8:17 - 8:33 - 8:49 - 8:65 - 8:81
# RAID4 - 4 data drives, 1 parity (no metadata devices)
# Chunk size of 1MiB, force RAID initialization,
# min recovery rate at 20 kiB/sec/disk
0 1960893648 raid \
raid4 4 2048 min_recovery_rate 20 sync\
5 - 8:17 - 8:33 - 8:49 - 8:65 - 8:81
Performing a 'dmsetup table' should display the CTR table used to
construct the mapping (with possible reordering of optional
parameters).
Performing a 'dmsetup status' will yield information on the state and
health of the array. The output is as follows:
1: <s> <l> raid \
2: <raid_type> <#devices> <1 health char for each dev> <resync_ratio>
Line 1 is standard DM output. Line 2 is best shown by example:
0 1960893648 raid raid4 5 AAAAA 2/490221568
Here we can see the RAID type is raid4, there are 5 devices - all of
which are 'A'live, and the array is 2/490221568 complete with recovery.
Cc: linux-raid@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
DM currently implements congestion checking by checking on congestion
in each component device. For raid456 we need to also check if the
stripe cache is congested.
Add per-target congestion checker callback support.
Extending the target_callbacks structure with additional callback
functions allows for establishing multiple callbacks per-target (a
callback is also needed for unplug).
Cc: linux-raid@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch adds a user-configurable 'pg_init_delay_msecs' feature. Use
this feature to specify the number of milliseconds to delay before
retrying scsi_dh_activate, when SCSI_DH_RETRY is returned.
SCSI Device Handlers return SCSI_DH_IMM_RETRY if we could retry
activation immediately and SCSI_DH_RETRY in cases where it is better to
retry after some delay.
Currently we immediately retry scsi_dh_activate irrespective of
SCSI_DH_IMM_RETRY and SCSI_DH_RETRY.
The 'pg_init_delay_msecs' feature may be provided during table create or
load, e.g.:
dmsetup create --table "0 20971520 multipath 3 queue_if_no_path \
pg_init_delay_msecs 2500 ..." mpatha
The default for 'pg_init_delay_msecs' is 2000 milliseconds.
Maximum configurable delay is 60000 milliseconds. Specifying a
'pg_init_delay_msecs' of 0 will cause immediate retry.
Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch changes spin_lock_irq() to spin_lock() in dm_request_fn().
This patch is just a clean-up and no functional change.
The spin_lock_irq() was leftover from the early request-based dm code,
where map_request() used to enable interrupts.
Since current map_request() never enables interrupts, we can change it
to spin_lock() to match the prior spin_unlock().
Auditing through the dm and block-layer code called from
map_request(), I confirmed all functions save/restore interrupt
status, so no function returning with interrupts enabled.
Also I haven't observed any problem on my test environment which
uses scsi and lpfc driver after heavy I/O testing with occasional
path down/up.
Added BUG_ON() to detect breakage in future.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
It's nicer to return the PTR_ERR() value instead of just returning
-ENOMEM. In the current code the PTR_ERR() value is always equal to
-ENOMEM so this doesn't actually affect anything, but still...
In addition, dm_dirty_log_create() doesn't check for a specific -ENOMEM
return. So this change is safe relative to potential for a non -ENOMEM
return in the future.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use dm_suspended() rather than having each snapshot target maintain a
private 'suspended' flag in struct dm_snapshot.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
metadata_wq serves on-stack work items from chunk_io(). Even if
multiple chunk_io() are simultaneously in progress, each is
independent and queued only once, so multithreaded workqueue can be
safely used.
Switch metadata_wq to multithread and flush the work item instead of
the workqueue in chunk_io().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
kmirrord_wq, kcopyd_work and md->wq are created per dm instance and
serve only a single work item from the dm instance, so non-reentrant
workqueues would provide the same ordering guarantees as ordered ones
while allowing CPU affinity and use of the workqueues for other
purposes. Switch them to non-reentrant workqueues.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Convert all create[_singlethread]_work() users to the new
alloc[_ordered]_workqueue(). This conversion is mechanical and
doesn't introduce any behavior change.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
kstriped only serves sc->kstriped_ws which runs dm_table_event().
This doesn't need to be executed from an ordered workqueue w/ rescuer.
Drop kstriped and use the system_wq instead. While at it, rename
kstriped_ws to trigger_event so that it's consistent with other dm
modules.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
flush_scheduled_work() is being deprecated. Flush the used work
directly instead. In all dm targets, the only work which uses
system_wq is ->trigger_event.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
dm_snapshot->queued_bios_work isn't used. Remove ->queued_bios[_work]
from dm_snapshot structure, the flush_queued_bios work function and
ksnapd workqueue.
The DM snapshot changes that were going to use the ksnapd workqueue were
either superseded (fix for origin write races) or never completed
(deallocation of invalid snapshot's memory via workqueue).
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The device-mapper should not send warning messages to syslog
if a device is not found. This can be done by userspace
according to the returned dm-ioctl error code.
So move these messages to debug level and use rate limiting
to not flood syslog.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch adds a compatible implementation of the block
chaining mode used by the Loop-AES block device encryption
system (http://loop-aes.sourceforge.net/) designed
by Jari Ruusu.
It operates on full 512 byte sectors and uses CBC
with an IV derived from the sector number, the data and
optionally extra IV seed.
This means that after CBC decryption the first block of sector
must be tweaked according to decrypted data.
Loop-AES can use three encryption schemes:
version 1: is plain aes-cbc mode (already compatible)
version 2: uses 64 multikey scheme with own IV generator
version 3: the same as version 2 with additional IV seed
(it uses 65 keys, last key is used as IV seed)
The IV generator is here named lmk (Loop-AES multikey)
and for the cipher specification looks like: aes:64-cbc-lmk
Version 2 and 3 is recognised according to length
of provided multi-key string (which is just hexa encoded
"raw key" used in original Loop-AES ioctl).
Configuration of the device and decoding key string will
be done in userspace (cryptsetup).
(Loop-AES stores keys in gpg encrypted file, raw keys are
output of simple hashing of lines in this file).
Based on an implementation by Max Vozeler:
http://article.gmane.org/gmane.linux.kernel.cryptoapi/3752/
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
CC: Max Vozeler <max@hinterhof.net>
This patch adds generic multikey handling to be used
in following patch for Loop-AES mode compatibility.
This patch extends mapping table to optional keycount and
implements generic multi-key capability.
With more keys defined the <key> string is divided into
several <keycount> sections and these are used for tfms.
The tfm is used according to sector offset
(sector 0->tfm[0], sector 1->tfm[1], sector N->tfm[N modulo keycount])
(only power of two values supported for keycount here).
Because of tfms per-cpu allocation, this mode can be take
a lot of memory on large smp systems.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: Max Vozeler <max@hinterhof.net>
IV (initialisation vector) can in principle depend not only
on sector but also on plaintext data (or other attributes).
Change IV generator interface to work directly with dmreq
structure to allow such dependence in generator.
Also add post() function which is called after the crypto
operation.
This allows tricky modification of decrypted data or IV
internals.
In asynchronous mode the post() can be called after
ctx->sector count was increased so it is needed
to add iv_sector copy directly to dmreq structure.
(N.B. dmreq always include only one sector in scatterlists)
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If there is enough memory, code can directly submit bio
instead queing this operation in separate thread.
Try to alloc bio clone with GFP_NOWAIT and only if it
fails use separate queue (map function cannot block here).
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Currently dm-crypt does all the encryption work for a single dm-crypt
mapping in a single workqueue. This does not scale well when multiple
CPUs are submitting IO at a high rate. The single CPU running the single
thread cannot keep up with the encryption and encrypted IO performance
tanks.
This patch changes the crypto workqueue to be per CPU. This means
that as long as the IO submitter (or the interrupt target CPUs
for reads) runs on different CPUs the encryption work will be also
parallel.
To avoid a bottleneck on the IO worker I also changed those to be
per-CPU threads.
There is still some shared data, so I suspect some bouncing
cache lines. But I haven't done a detailed study on that yet.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Rename cc->cipher_mode to cc->cipher_string and store the whole of the cipher
information so it can easily be printed when processing the DM_DEV_STATUS ioctl.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch adds a 'version' field to the 'dm_ulog_request'
structure.
The 'version' field is taken from a portion of the unused
'padding' field in the 'dm_ulog_request' structure. This
was done to avoid changing the size of the structure and
possibly disrupting backwards compatibility.
The version number will help notify user-space daemons
when a change has been made to the kernel/userspace
log API.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Allow the device-mapper log's 'mark' and 'clear' requests to be
grouped and processed in a batch. This can significantly reduce the
amount of traffic going between the kernel and userspace (where the
processing daemon resides).
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Split the 'flush_list', which contained a mix of both 'mark' and 'clear'
requests, into two distinct lists ('mark_list' and 'clear_list').
The device mapper log implementations (used by various DM targets) are
allowed to cache 'mark' and 'clear' requests until a 'flush' is
received. Until now, these cached requests were kept in the same list.
They will now be put into distinct lists to facilitate group processing
of these requests (in the next patch).
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Make kcopyd merge more I/O requests by using device unplugging.
Without this patch, each I/O request is dispatched separately to the device.
If the device supports tagged queuing, there are many small requests sent
to the device. To improve performance, this patch will batch as many requests
as possible, allowing the queue to merge consecutive requests, and send them
to the device at once.
In my tests (15k SCSI disk), this patch improves sequential write throughput:
Sequential write throughput (chunksize of 4k, 32k, 512k)
unpatched: 15.2, 18.5, 17.5 MB/s
patched: 14.4, 22.6, 23.0 MB/s
In most common uses (snapshot or two-way mirror), kcopyd is only used for
two devices, one for reading and the other for writing, thus this optimization
is implemented only for two devices. The optimization may be extended to n-way
mirrors with some code complexity increase.
We keep track of two block devices to unplug (one for read and the
other for write) and unplug them when exiting "do_work" thread. If
there are more devices used (in theory it could happen, in practice it
is rare), we unplug immediately.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
When constructing a mirror log, it is possible for the initial request
to fail for other reasons besides -ESRCH. These must be handled too.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Simplify key size verification (hexadecimal string) and
set key size early in constructor.
(Patch required by later changes.)
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch replaces dm_mutex with _minor_lock in dm_blk_close()
and then removes it.
During the BKL conversion, commit 6e9624b8ca
(block: push down BKL into .open and .release) pushed lock_kernel()
down into dm_blk_open/close calls.
Commit 2a48fc0ab2
(block: autoconvert trivial BKL users to private mutex) converted it to a
local mutex, but _minor_lock is sufficient.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Enable discard support in the DM mirror target.
Also change an existing use of 'bvec' to 'addr' in the union.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Allow the uuid of a mapped device to be set after device creation.
Previously the uuid (which is optional) could only be set by
DM_DEV_CREATE. If no uuid was supplied it could not be set later.
Sometimes it's necessary to create the device before the uuid is known,
and in such cases the uuid must be filled in after the creation.
This patch extends DM_DEV_RENAME to accept a uuid accompanied by
a new flag DM_UUID_FLAG. This can only be done once and if no
uuid was previously supplied. It cannot be used to change an
existing uuid.
DM_VERSION_MINOR is also bumped to 19 to indicate this interface
extension is available.
Signed-off-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove the REQ_SYNC flag to improve write throughput when writing
to the origin with a snapshot on the same device (using the CFQ I/O
scheduler).
Sequential write throughput (chunksize of 4k, 32k, 512k)
unpatched: 8.5, 8.6, 9.3 MB/s
patched: 15.2, 18.5, 17.5 MB/s
Snapshot exception reallocations are triggered by writes that are
usually async, so mark the associated dm_io_request as async as well.
This helps when using the CFQ I/O scheduler because it has separate
queues for sync and async I/O. Async is optimized for throughput; sync
for latency. With this change we're consciously favoring throughput over
latency.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Revert commit 224cb3e981
dm: Call blk_abort_queue on failed paths
Multipath began to use blk_abort_queue() to allow for
lower latency path deactivation. This was found to
cause list corruption:
the cmd gets blk_abort_queued/timedout run on it and the scsi eh
somehow is able to complete and run scsi_queue_insert while
scsi_request_fn is still trying to process the request.
https://www.redhat.com/archives/dm-devel/2010-November/msg00085.html
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: Mike Anderson <andmike@linux.vnet.ibm.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: stable@kernel.org
No longer needlessly hold md->bdev->bd_inode->i_mutex when changing the
size of a DM device. This additional locking is unnecessary because
i_size_write() is already protected by the existing critical section in
dm_swap_table(). DM already has a reference on md->bdev so the
associated bd_inode may be changed without lifetime concerns.
A negative side-effect of having held md->bdev->bd_inode->i_mutex was
that a concurrent DM device resize and flush (via fsync) would deadlock.
Dropping md->bdev->bd_inode->i_mutex eliminates this potential for
deadlock. The following reproducer no longer deadlocks:
https://www.redhat.com/archives/dm-devel/2009-July/msg00284.html
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: stable@kernel.org
* 'for-2.6.38/core' of git://git.kernel.dk/linux-2.6-block: (43 commits)
block: ensure that completion error gets properly traced
blktrace: add missing probe argument to block_bio_complete
block cfq: don't use atomic_t for cfq_group
block cfq: don't use atomic_t for cfq_queue
block: trace event block fix unassigned field
block: add internal hd part table references
block: fix accounting bug on cross partition merges
kref: add kref_test_and_get
bio-integrity: mark kintegrityd_wq highpri and CPU intensive
block: make kblockd_workqueue smarter
Revert "sd: implement sd_check_events()"
block: Clean up exit_io_context() source code.
Fix compile warnings due to missing removal of a 'ret' variable
fs/block: type signature of major_to_index(int) to major_to_index(unsigned)
block: convert !IS_ERR(p) && p to !IS_ERR_NOR_NULL(p)
cfq-iosched: don't check cfqg in choose_service_tree()
fs/splice: Pull buf->ops->confirm() from splice_from_pipe actors
cdrom: export cdrom_check_events()
sd: implement sd_check_events()
sr: implement sr_check_events()
...
Commit 1a855a0606 (2.6.37-rc4) fixed a problem where devices were
re-added when they shouldn't be but caused a regression in a less
common case that means sometimes devices cannot be re-added when they
should be.
In particular, when re-adding a device to an array without metadata
we should always access the device, but after the above commit we
didn't.
This patch sets the In_sync flag in that case so that the re-add
succeeds.
This patch is suitable for any -stable kernel to which 1a855a0606 was
applied.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
The "error" field in block_bio_complete is not assigned, leaving the memory area
uninitialized (keeping garbage data). Pass an additional tracepoint argument to
this event to initialize this field.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
CC: Steven Rostedt <rostedt@goodmis.org>
CC: Frederic Weisbecker <fweisbec@gmail.com>
CC: Ingo Molnar <mingo@elte.hu>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Li Zefan <lizf@cn.fujitsu.com>
CC: Alan.Brunelle@hp.com
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cciss: fix cciss_revalidate panic
block: max hardware sectors limit wrapper
block: Deprecate QUEUE_FLAG_CLUSTER and use queue_limits instead
blk-throttle: Correct the placement of smp_rmb()
blk-throttle: Trim/adjust slice_end once a bio has been dispatched
block: check for proper length of iov entries earlier in blk_rq_map_user_iov()
drbd: fix for spin_lock_irqsave in endio callback
drbd: don't recvmsg with zero length
Implement blk_limits_max_hw_sectors() and make
blk_queue_max_hw_sectors() a wrapper around it.
DM needs this to avoid setting queue_limits' max_hw_sectors and
max_sectors directly. dm_set_device_limits() now leverages
blk_limits_max_hw_sectors() logic to establish the appropriate
max_hw_sectors minimum (PAGE_SIZE). Fixes issue where DM was
incorrectly setting max_sectors rather than max_hw_sectors (which
caused dm_merge_bvec()'s max_hw_sectors check to be ineffective).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
When stacking devices, a request_queue is not always available. This
forced us to have a no_cluster flag in the queue_limits that could be
used as a carrier until the request_queue had been set up for a
metadevice.
There were several problems with that approach. First of all it was up
to the stacking device to remember to set queue flag after stacking had
completed. Also, the queue flag and the queue limits had to be kept in
sync at all times. We got that wrong, which could lead to us issuing
commands that went beyond the max scatterlist limit set by the driver.
The proper fix is to avoid having two flags for tracking the same thing.
We deprecate QUEUE_FLAG_CLUSTER and use the queue limit directly in the
block layer merging functions. The queue_limit 'no_cluster' is turned
into 'cluster' to avoid double negatives and to ease stacking.
Clustering defaults to being enabled as before. The queue flag logic is
removed from the stacking function, and explicitly setting the cluster
flag is no longer necessary in DM and MD.
Reported-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
When we fail to start a raid10 for some reason, we call
md_unregister_thread to kill the thread that was created.
Unfortunately md_thread() will then make one call into the handler
(raid10d) even though md_wakeup_thread has not been called. This is
not safe and as md_unregister_thread is called after mddev->private
has been set to NULL, it will definitely cause a NULL dereference.
So fix this at both ends:
- md_thread should only call the handler if THREAD_WAKEUP has been
set.
- raid10 should call md_unregister_thread before setting things
to NULL just like all the other raid modules do.
This is applicable to 2.6.35 and later.
Cc: stable@kernel.org
Reported-by: "Citizen" <citizen_lee@thecus.com>
Signed-off-by: NeilBrown <neilb@suse.de>
With v0.90 metadata, a hot-spare does not become a full member of the
array until recovery is complete. So if we re-add such a device to
the array, we know that all of it is as up-to-date as the event count
would suggest, and so it a bitmap-based recovery is possible.
However with v1.x metadata, the hot-spare immediately becomes a full
member of the array, but it record how much of the device has been
recovered. If the array is stopped and re-assembled recovery starts
from this point.
When such a device is hot-added to an array we currently lose the 'how
much is recovered' information and incorrectly included it as a full
in-sync member (after bitmap-based fixup).
This is wrong and unsafe and could corrupt data.
So be more careful about setting saved_raid_disk - which is what
guides the re-adding of devices back into an array.
The new code matches the code in slot_store which does a similar
thing, which is encouraging.
This is suitable for any -stable kernel.
Reported-by: "Dailey, Nate" <Nate.Dailey@stratus.com>
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
As recorded in
https://bugzilla.kernel.org/show_bug.cgi?id=24012
it is possible for a flush request through md to hang. This is due to
an interaction between the recursion avoidance in
generic_make_request, the insistence in md of only having one flush
active at a time, and the possibility of dm (or md) submitting two
flush requests to a device from the one generic_make_request.
If a generic_make_request call into dm causes two flush requests to be
queued (as happens if the dm table has two targets - they get one
each), these two will be queued inside generic_make_request.
Assume they are for the same md device.
The first is processed and causes 1 or more flush requests to be sent
to lower devices. These get queued within generic_make_request too.
Then the second flush to the md device gets handled and it blocks
waiting for the first flush to complete. But it won't complete until
the two lower-device requests complete, and they haven't even been
submitted yet as they are on the generic_make_request queue.
The deadlock can be broken by using a separate thread to submit the
requests to lower devices. md has such a thread readily available:
md_wq.
So use it to submit these requests.
Reported-by: Giacomo Catenazzi <cate@cateee.net>
Tested-by: Giacomo Catenazzi <cate@cateee.net>
Signed-off-by: NeilBrown <neilb@suse.de>
submit_flushes is called from exactly one place.
Move the code that is before and after that call into
submit_flushes.
This has not functional change, but will make the next patch
smaller and easier to follow.
Signed-off-by: NeilBrown <neilb@suse.de>
None of the functions called between setting flush_pending to 1, and
atomic_dec_and_test can change flush_pending, or will anything
running in any other thread (as ->flush_bio is not NULL). So the
atomic_dec_and_test will always succeed.
So remove the atomic_sec and the atomic_dec_and_test.
Signed-off-by: NeilBrown <neilb@suse.de>
Before 2.6.37, the md layer had a mechanism for catching I/Os with the
barrier flag set, and translating the barrier into barriers for all
the underlying devices. With 2.6.37, I/O barriers have become plain
old flushes, and the md code was updated to reflect this. However,
one piece was left out -- the md layer does not tell the block layer
that it supports flushes or FUA access at all, which results in md
silently dropping flush requests.
Since the support already seems there, just add this one piece of
bookkeeping.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Commit 4044ba58dd supposedly fixed a
problem where if a raid1 with just one good device gets a read-error
during recovery, the recovery would abort and immediately restart in
an infinite loop.
However it depended on raid1_remove_disk removing the spare device
from the array. But that does not happen in this case. So add a test
so that in the 'recovery_disabled' case, the device will be removed.
This suitable for any kernel since 2.6.29 which is when
recovery_disabled was introduced.
Cc: stable@kernel.org
Reported-by: Sebastian Färber <faerber@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When trying to grow an array by enlarging component devices,
rdev_size_store() expects the return value of rdev_size_change() to be
in sectors, but the actual value is returned in KBs.
This functionality was broken by commit
dd8ac336c1
so this patch is suitable for any kernel since 2.6.30.
Cc: stable@kernel.org
Signed-off-by: Justin Maggard <jmaggard10@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
After recent blkdev_get() modifications, open_by_devnum() and
open_bdev_exclusive() are simple wrappers around blkdev_get().
Replace them with blkdev_get_by_dev() and blkdev_get_by_path().
blkdev_get_by_dev() is identical to open_by_devnum().
blkdev_get_by_path() is slightly different in that it doesn't
automatically add %FMODE_EXCL to @mode.
All users are converted. Most conversions are mechanical and don't
introduce any behavior difference. There are several exceptions.
* btrfs now sets FMODE_EXCL in btrfs_device->mode, so there's no
reason to OR it explicitly on blkdev_put().
* gfs2, nilfs2 and the generic mount_bdev() now set FMODE_EXCL in
sb->s_mode.
* With the above changes, sb->s_mode now always should contain
FMODE_EXCL. WARN_ON_ONCE() added to kill_block_super() to detect
errors.
The new blkdev_get_*() functions are with proper docbook comments.
While at it, add function description to blkdev_get() too.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Joern Engel <joern@lazybastard.org>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Jan Kara <jack@suse.cz>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: KONISHI Ryusuke <konishi.ryusuke@lab.ntt.co.jp>
Cc: reiserfs-devel@vger.kernel.org
Cc: xfs-masters@oss.sgi.com
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Over time, block layer has accumulated a set of APIs dealing with bdev
open, close, claim and release.
* blkdev_get/put() are the primary open and close functions.
* bd_claim/release() deal with exclusive open.
* open/close_bdev_exclusive() are combination of open and claim and
the other way around, respectively.
* bd_link/unlink_disk_holder() to create and remove holder/slave
symlinks.
* open_by_devnum() wraps bdget() + blkdev_get().
The interface is a bit confusing and the decoupling of open and claim
makes it impossible to properly guarantee exclusive access as
in-kernel open + claim sequence can disturb the existing exclusive
open even before the block layer knows the current open if for another
exclusive access. Reorganize the interface such that,
* blkdev_get() is extended to include exclusive access management.
@holder argument is added and, if is @FMODE_EXCL specified, it will
gain exclusive access atomically w.r.t. other exclusive accesses.
* blkdev_put() is similarly extended. It now takes @mode argument and
if @FMODE_EXCL is set, it releases an exclusive access. Also, when
the last exclusive claim is released, the holder/slave symlinks are
removed automatically.
* bd_claim/release() and close_bdev_exclusive() are no longer
necessary and either made static or removed.
* bd_link_disk_holder() remains the same but bd_unlink_disk_holder()
is no longer necessary and removed.
* open_bdev_exclusive() becomes a simple wrapper around lookup_bdev()
and blkdev_get(). It also has an unexpected extra bdev_read_only()
test which probably should be moved into blkdev_get().
* open_by_devnum() is modified to take @holder argument and pass it to
blkdev_get().
Most of bdev open/close operations are unified into blkdev_get/put()
and most exclusive accesses are tested atomically at the open time (as
it should). This cleans up code and removes some, both valid and
invalid, but unnecessary all the same, corner cases.
open_bdev_exclusive() and open_by_devnum() can use further cleanup -
rename to blkdev_get_by_path() and blkdev_get_by_devt() and drop
special features. Well, let's leave them for another day.
Most conversions are straight-forward. drbd conversion is a bit more
involved as there was some reordering, but the logic should stay the
same.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Neil Brown <neilb@suse.de>
Acked-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Peter Osterlund <petero2@telia.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <joel.becker@oracle.com>
Cc: Alex Elder <aelder@sgi.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: dm-devel@redhat.com
Cc: drbd-dev@lists.linbit.com
Cc: Leo Chen <leochen@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Cc: Joern Engel <joern@logfs.org>
Cc: reiserfs-devel@vger.kernel.org
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Code to manage symlinks in /sys/block/*/{holders|slaves} are overly
complex with multiple holder considerations, redundant extra
references to all involved kobjects, unused generic kobject holder
support and unnecessary mixup with bd_claim/release functionalities.
Strip it down to what's necessary (single gendisk holder) and make it
use a separate interface. This is a step for cleaning up
bd_claim/release. This patch makes dm-table slightly more complex but
it will be simplified again with further changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Neil Brown <neilb@suse.de>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Cc: dm-devel@redhat.com
Convert direct reads of an inode's i_size to using i_size_read().
i_size_{read,write} use a seqcount to protect reads from accessing
incomple writes. Concurrent i_size_write()s require mutual exclussion
to protect the seqcount that is used by i_size_{read,write}. But
i_size_read() callers do not need to use additional locking.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: NeilBrown <neilb@suse.de>
Acked-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The code for searching through the device list to read-balance in
raid1 is rather clumsy and hard to follow. Try to simplify it a bit.
No important functionality change here.
Signed-off-by: NeilBrown <neilb@suse.de>
When writing to an 'external' bitmap we don't currently unplug the
device before waiting, so we can get a 3msec delay each time;
So use REQ_UNPLUG to force and unplug.
Signed-off-by: NeilBrown <neilb@suse.de>
bio_clone and bio_alloc allocate from a common bio pool.
If an md device is stacked with other devices that use this pool, or under
something like swap which uses the pool, then the multiple calls on
the pool can cause deadlocks.
So allocate a local bio pool for each md array and use that rather
than the common pool.
This pool is used both for regular IO and metadata updates.
Signed-off-by: NeilBrown <neilb@suse.de>
Currently sync_page_io takes a 'bdev'.
Every caller passes 'rdev->bdev'.
We will soon want another field out of the rdev in sync_page_io,
So just pass the rdev instead of the bdev out of it.
Signed-off-by: NeilBrown <neilb@suse.de>
Though this mem alloc is GFP_NOIO an so will not deadlock, it seems
better to do the allocation before 'raise_barrier' which stops any IO
requests while the resync proceeds.
raid10 always uses this order, so it is at least consistent to do the
same in raid1.
Signed-off-by: NeilBrown <neilb@suse.de>
bio_alloc can never fail (as it uses a mempool) but an block
indefinitely, especially if the caller is holding a reference to a
previously allocated bio.
So these to places which both handle failure and hold multiple bios
should not use bio_alloc, they should use bio_kmalloc.
Signed-off-by: NeilBrown <neilb@suse.de>
It is not safe to allocate from a mempool while holding an item
previously allocated from that mempool as that can deadlock when the
mempool is close to exhaustion.
So don't use a bio list to collect the bios to write to multiple
devices in raid1 and raid10.
Instead queue each bio as it becomes available so an unplug will
activate all previously allocated bios and so a new bio has a chance
of being allocated.
This means we must set the 'remaining' count to '1' before submitting
any requests, then when all are submitted, decrement 'remaining' and
possible handle the write completion at that point.
Reported-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Workqueue usage in md has two problems.
* Flush can be used during or depended upon by memory reclaim, but md
uses the system workqueue for flush_work which may lead to deadlock.
* md depends on flush_scheduled_work() to achieve exclusion against
completion of removal of previous instances. flush_scheduled_work()
may incur unexpected amount of delay and is scheduled to be removed.
This patch adds two workqueues to md - md_wq and md_misc_wq. The
former is guaranteed to make forward progress under memory pressure
and serves flush_work. The latter serves as the flush domain for
other works.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: NeilBrown <neilb@suse.de>
bitmap_get_counter returns the number of sectors covered
by the counter in a pass-by-reference variable.
In some cases this can be very large, so make it a sector_t
for safety.
Signed-off-by: NeilBrown <neilb@suse.de>
lock_kernel calls were recently pushed down into open/release
functions.
md doesn't need that protection.
Then the BKL calls were change to md_mutex. We don't need those
either.
So remove it all.
Signed-off-by: NeilBrown <neilb@suse.de>
A RAID1 which has no persistent metadata, whether internal or
external, will hang on the first write.
This is caused by commit 070dc6dd71
In that case, MD_CHANGE_PENDING never gets cleared.
So during md_update_sb, is neither persistent or external,
clear MD_CHANGE_PENDING.
This is suitable for 2.6.36-stable.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
Silly though it is, completions and wait_queue_heads use foo_ONSTACK
(COMPLETION_INITIALIZER_ONSTACK, DECLARE_COMPLETION_ONSTACK,
__WAIT_QUEUE_HEAD_INIT_ONSTACK and DECLARE_WAIT_QUEUE_HEAD_ONSTACK) so I
guess workqueues should do the same thing.
s/INIT_WORK_ON_STACK/INIT_WORK_ONSTACK/
s/INIT_DELAYED_WORK_ON_STACK/INIT_DELAYED_WORK_ONSTACK/
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-2.6.37/barrier' of git://git.kernel.dk/linux-2.6-block: (46 commits)
xen-blkfront: disable barrier/flush write support
Added blk-lib.c and blk-barrier.c was renamed to blk-flush.c
block: remove BLKDEV_IFL_WAIT
aic7xxx_old: removed unused 'req' variable
block: remove the BH_Eopnotsupp flag
block: remove the BLKDEV_IFL_BARRIER flag
block: remove the WRITE_BARRIER flag
swap: do not send discards as barriers
fat: do not send discards as barriers
ext4: do not send discards as barriers
jbd2: replace barriers with explicit flush / FUA usage
jbd2: Modify ASYNC_COMMIT code to not rely on queue draining on barrier
jbd: replace barriers with explicit flush / FUA usage
nilfs2: replace barriers with explicit flush / FUA usage
reiserfs: replace barriers with explicit flush / FUA usage
gfs2: replace barriers with explicit flush / FUA usage
btrfs: replace barriers with explicit flush / FUA usage
xfs: replace barriers with explicit flush / FUA usage
block: pass gfp_mask and flags to sb_issue_discard
dm: convey that all flushes are processed as empty
...
* 'for-2.6.37/core' of git://git.kernel.dk/linux-2.6-block: (39 commits)
cfq-iosched: Fix a gcc 4.5 warning and put some comments
block: Turn bvec_k{un,}map_irq() into static inline functions
block: fix accounting bug on cross partition merges
block: Make the integrity mapped property a bio flag
block: Fix double free in blk_integrity_unregister
block: Ensure physical block size is unsigned int
blkio-throttle: Fix possible multiplication overflow in iops calculations
blkio-throttle: limit max iops value to UINT_MAX
blkio-throttle: There is no need to convert jiffies to milli seconds
blkio-throttle: Fix link failure failure on i386
blkio: Recalculate the throttled bio dispatch time upon throttle limit change
blkio: Add root group to td->tg_list
blkio: deletion of a cgroup was causes oops
blkio: Do not export throttle files if CONFIG_BLK_DEV_THROTTLING=n
block: set the bounce_pfn to the actual DMA limit rather than to max memory
block: revert bad fix for memory hotplug causing bounces
Fix compile error in blk-exec.c for !CONFIG_DETECT_HUNG_TASK
block: set the bounce_pfn to the actual DMA limit rather than to max memory
block: Prevent hang_check firing during long I/O
cfq: improve fsync performance for small files
...
Fix up trivial conflicts due to __rcu sparse annotation in include/linux/genhd.h
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
block: autoconvert trivial BKL users to private mutex
drivers: autoconvert trivial BKL users to private mutex
ipmi: autoconvert trivial BKL users to private mutex
mac: autoconvert trivial BKL users to private mutex
mtd: autoconvert trivial BKL users to private mutex
scsi: autoconvert trivial BKL users to private mutex
Fix up trivial conflicts (due to addition of private mutex right next to
deletion of a version string) in drivers/char/pcmcia/cm40[04]0_cs.c
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
Function read_sb_page may return ERR_PTR(...). Check for it.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NeilBrown <neilb@suse.de>
When performing a resync we pre-allocate some bios and repeatedly use
them. This requires us to re-initialise them each time.
One field (bi_comp_cpu) and some flags weren't being initiaised
reliably.
Signed-off-by: NeilBrown <neilb@suse.de>
bitmap_start_sync returns - via a pass-by-reference variable - the
number of sectors before we need to check with the bitmap again.
Since commit ef42567335 this number can be substantially larger,
2^27 is a common value.
Unfortunately it is an 'int' and so when raid1.c:sync_request shifts
it 9 places to the left it becomes 0. This results in a zero-length
read which the scsi layer justifiably complains about.
This patch just removes the shift so the common case becomes safe with
a trivially-correct patch.
In the next merge window we will convert this 'int' to a 'sector_t'
Reported-by: "George Spelvin" <linux@horizon.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The block device drivers have all gained new lock_kernel
calls from a recent pushdown, and some of the drivers
were already using the BKL before.
This turns the BKL into a set of per-driver mutexes.
Still need to check whether this is safe to do.
file=$1
name=$2
if grep -q lock_kernel ${file} ; then
if grep -q 'include.*linux.mutex.h' ${file} ; then
sed -i '/include.*<linux\/smp_lock.h>/d' ${file}
else
sed -i 's/include.*<linux\/smp_lock.h>.*$/include <linux\/mutex.h>/g' ${file}
fi
sed -i ${file} \
-e "/^#include.*linux.mutex.h/,$ {
1,/^\(static\|int\|long\)/ {
/^\(static\|int\|long\)/istatic DEFINE_MUTEX(${name}_mutex);
} }" \
-e "s/\(un\)*lock_kernel\>[ ]*()/mutex_\1lock(\&${name}_mutex)/g" \
-e '/[ ]*cycle_kernel_lock();/d'
else
sed -i -e '/include.*\<smp_lock.h\>/d' ${file} \
-e '/cycle_kernel_lock()/d'
fi
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
If an array with 1.x metadata is assembled with the last disk missing,
md doesn't properly record the fact that the disk was missing.
This is unlikely to cause a real problem as the event count will be
different to the count on the missing disk so it won't be included in
the array. However it could still cause confusion.
So make sure we clear all the relevant slots, not just the early ones.
Signed-off-by: NeilBrown <neilb@suse.de>
Now that we depend on md_update_sb to clear variable bits in
mddev->flags (rather than trying not to set them) it is important to
always call md_update_sb when appropriate.
md_check_recovery has this job but explicitly avoids it for ->external
metadata arrays. This is not longer appropraite, or needed.
However we do want to avoid taking the mddev lock if only
MD_CHANGE_PENDING is set as that is not cleared by md_update_sb for
external-metadata arrays.
Reported-by: "Kwolek, Adam" <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
We have several users of min_not_zero, each of them using their own
definition. Move the define to kernel.h.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@carl.home.kernel.dk>
Rename __clone_and_map_flush to __clone_and_map_empty_flush for added
clarity.
Simplify logic associated with REQ_FLUSH conditionals.
Introduce a BUG_ON() and add a few more helpful comments to the code
so that it is clear that all flushes are empty.
Cleanup __split_and_process_bio() so that an empty flush isn't processed
by a 'sector_count' focused while loop.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Now queue_io() is called from dec_pending(), which may be called with
interrupts disabled, so queue_io() must not enable interrupts
unconditionally and must save/restore the current interrupts status.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Unlike REQ_HARDBARRIER, REQ_FLUSH/FUA doesn't mandate any ordering
against other bio's. This patch relaxes ordering around flushes.
* A flush bio is no longer deferred to workqueue directly. It's
processed like other bio's but __split_and_process_bio() uses
md->flush_bio as the clone source. md->flush_bio is initialized to
empty flush during md initialization and shared for all flushes.
* As a flush bio now travels through the same execution path as other
bio's, there's no need for dedicated error handling path either. It
can use the same error handling path in dec_pending(). Dedicated
error handling removed along with md->flush_error.
* When dec_pending() detects that a flush has completed, it checks
whether the original bio has data. If so, the bio is queued to the
deferred list w/ REQ_FLUSH cleared; otherwise, it's completed.
* As flush sequencing is handled in the usual issue/completion path,
dm_wq_work() no longer needs to handle flushes differently. Now its
only responsibility is re-issuing deferred bio's the same way as
_dm_request() would. REQ_FLUSH handling logic including
process_flush() is dropped.
* There's no reason for queue_io() and dm_wq_work() write lock
dm->io_lock. queue_io() now only uses md->deferred_lock and
dm_wq_work() read locks dm->io_lock.
* bio's no longer need to be queued on the deferred list while a flush
is in progress making DMF_QUEUE_IO_TO_THREAD unncessary. Drop it.
This avoids stalling the device during flushes and simplifies the
implementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This patch converts request-based dm to support the new REQ_FLUSH/FUA.
The original request-based flush implementation depended on
request_queue blocking other requests while a barrier sequence is in
progress, which is no longer true for the new REQ_FLUSH/FUA.
In general, request-based dm doesn't have infrastructure for cloning
one source request to multiple targets, but the original flush
implementation had a special mostly independent path which can issue
flushes to multiple targets and sequence them. However, the
capability isn't currently in use and adds a lot of complexity.
Moreoever, it's unlikely to be useful in its current form as it
doesn't make sense to be able to send out flushes to multiple targets
when write requests can't be.
This patch rips out special flush code path and deals handles
REQ_FLUSH/FUA requests the same way as other requests. The only
special treatment is that REQ_FLUSH requests use the block address 0
when finding target, which is enough for now.
* added BUG_ON(!dm_target_is_valid(ti)) in dm_request_fn() as
suggested by Mike Snitzer
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Tested-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This patch converts bio-based dm to support REQ_FLUSH/FUA instead of
now deprecated REQ_HARDBARRIER.
* -EOPNOTSUPP handling logic dropped.
* Preflush is handled as before but postflush is dropped and replaced
with passing down REQ_FUA to member request_queues. This replaces
one array wide cache flush w/ member specific FUA writes.
* __split_and_process_bio() now calls __clone_and_map_flush() directly
for flushes and guarantees all FLUSH bio's going to targets are zero
` length.
* It's now guaranteed that all FLUSH bio's which are passed onto dm
targets are zero length. bio_empty_barrier() tests are replaced
with REQ_FLUSH tests.
* Empty WRITE_BARRIERs are replaced with WRITE_FLUSHes.
* Dropped unlikely() around REQ_FLUSH tests. Flushes are not unlikely
enough to be marked with unlikely().
* Block layer now filters out REQ_FLUSH/FUA bio's if the request_queue
doesn't support cache flushing. Advertise REQ_FLUSH | REQ_FUA
capability.
* Request based dm isn't converted yet. dm_init_request_based_queue()
resets flush support to 0 for now. To avoid disturbing request
based dm code, dm->flush_error is added for bio based dm while
requested based dm continues to use dm->barrier_error.
Lightly tested linear, stripe, raid1, snap and crypt targets. Please
proceed with caution as I'm not familiar with the code base.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: dm-devel@redhat.com
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This patch converts md to support REQ_FLUSH/FUA instead of now
deprecated REQ_HARDBARRIER. In the core part (md.c), the following
changes are notable.
* Unlike REQ_HARDBARRIER, REQ_FLUSH/FUA don't interfere with
processing of other requests and thus there is no reason to mark the
queue congested while FLUSH/FUA is in progress.
* REQ_FLUSH/FUA failures are final and its users don't need retry
logic. Retry logic is removed.
* Preflush needs to be issued to all member devices but FUA writes can
be handled the same way as other writes - their processing can be
deferred to request_queue of member devices. md_barrier_request()
is renamed to md_flush_request() and simplified accordingly.
For linear, raid0 and multipath, the core changes are enough. raid1,
5 and 10 need the following conversions.
* raid1: Handling of FLUSH/FUA bio's can simply be deferred to
request_queues of member devices. Barrier related logic removed.
* raid5: Queue draining logic dropped. FUA bit is propagated through
biodrain and stripe resconstruction such that all the updated parts
of the stripe are written out with FUA writes if any of the dirtying
writes was FUA. preread_active_stripes handling in make_request()
is updated as suggested by Neil Brown.
* raid10: FUA bit needs to be propagated to write clones.
linear, raid0, 1, 5 and 10 tested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Neil Brown <neilb@suse.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Barrier is deemed too heavy and will soon be replaced by FLUSH/FUA
requests. Deprecate barrier. All REQ_HARDBARRIERs are failed with
-EOPNOTSUPP and blk_queue_ordered() is replaced with simpler
blk_queue_flush().
blk_queue_flush() takes combinations of REQ_FLUSH and FUA. If a
device has write cache and can flush it, it should set REQ_FLUSH. If
the device can handle FUA writes, it should also set REQ_FUA.
All blk_queue_ordered() users are converted.
* ORDERED_DRAIN is mapped to 0 which is the default value.
* ORDERED_DRAIN_FLUSH is mapped to REQ_FLUSH.
* ORDERED_DRAIN_FLUSH_FUA is mapped to REQ_FLUSH | REQ_FUA.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Alasdair G Kergon <agk@redhat.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
MD_CHANGE_CLEAN is used for two different purposes and this leads to
confusion.
One of the purposes is largely mirrored by MD_CHANGE_PENDING which is
not used for anything else, so have MD_CHANGE_PENDING take over that
purpose fully.
The two purposes are:
1/ tell md_update_sb that an update is needed and that it is just a
clean/dirty transition.
2/ tell user-space that an transition from clean to dirty is pending
(something wants to write), and tell te kernel (by clearin the
flag) that the transition is OK.
The first purpose remains wit MD_CHANGE_CLEAN, the second is moved
fully to MD_CHANGE_PENDING.
This means that various places which conditionally set or cleared
MD_CHANGE_CLEAN no longer need to be conditional.
Signed-off-by: NeilBrown <neilb@suse.de>
If this bit is cleared in md_update_sb() the kernel will allow writes to the
array if userspace triggers md_allow_write(), e.g. through stripe_cache_size,
when mdmon is not active. When mdmon is active the array transitions to
active-idle bypassing write-pending, setting up a race for mdmon to set the
array clean before a write arrives.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
commit 7b6d91daee changed the behaviour
of a few variables in raid1 and raid10 from flags to bit-sets, but
left them as type 'bool' so they did not work.
Change them (back) to unsigned long.
(historical note: see 1ef04fefe2)
Signed-off-by: NeilBrown <neilb@suse.de>
Reported-by: Jiri Slaby <jslaby@suse.cz> and many others
md_check_recovery expects ->spare_active to return 'true' if any
spares were activated, but none of them do, so the consequent change
in 'degraded' is not notified through sysfs.
So count the number of spares activated, subtract it from 'degraded'
just once, and return it.
Reported-by: Adrian Drzewiecki <adriand@vmware.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When RAID1 is done syncing disks, it'll update the state
of synced rdevs to In_sync. But it neglected to notify
sysfs that the attribute changed. So any programs that
are waiting for an rdev's state to change will not be
woken.
(raid5/raid10 added by neilb)
Signed-off-by: Adrian Drzewiecki <adriand@vmware.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The update of ->recovery_offset in sync_sbs is appropriate even then external
metadata is in use. However sync_sbs is only called when native
metadata is used.
So move that update in to the top of md_update_sb (which is the only
caller of sync_sbs) before the test on ->external.
This moves the update out of ->write_lock protection, but those fields
only need ->reconfig_mutex protection which they still have.
Also move the test on ->persistent up to where ->external is set as
for metadata update purposes they are the same.
Clear MD_CHANGE_DEVS and MD_CHANGE_CLEAN as they can only be confusing
if ->external is set or ->persistent isn't.
Finally move the update of ->utime down as it is only relevent (like
the ->events update) for native metadata.
Signed-off-by: NeilBrown <neilb@suse.de>
Reported-by: "Kwolek, Adam" <adam.kwolek@intel.com>
Enable discard support in the DM multipath target.
This discard support depends on a few discard-specific fixes to the
block layer's request stacking driver methods.
Discard requests are optional so don't allow a failed discard to trigger
path failures. If there is a real problem with a given path the
barriers associated with the discard (either before or after the
discard) will cause path failure. That said, unconditionally passing
discard failures up the stack is not ideal. This must be fixed once DM
has more information about the nature of the underlying storage failure.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
The DM core will submit a discard bio to the stripe target for each
stripe in a striped DM device. The stripe target will determine
stripe-specific portions of the supplied bio to be remapped into
individual (at most 'num_discard_requests' extents). If a given
stripe-specific discard bio doesn't touch a particular stripe the bio
will be dropped.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Update __clone_and_map_discard to loop across all targets in a DM
device's table when it processes a discard bio. If a discard crosses a
target boundary it must be split accordingly.
Update __issue_target_requests and __issue_target_request to allow a
cloned discard bio to have a custom start sector and size.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Optimize sector division: If the number of stripes is a power of two,
we can do shift and mask instead of division.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move sector to stripe translation into a function.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Have the error target respond to a discard request with a hard -EIO
rather than fail the request with -EOPNOTSUPP.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Have the zero target silently drop a discard rather than fail the
request with -EOPNOTSUPP.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Split max_io_len_target_boundary out of max_io_len so that the discard
support can make use of it without duplicating max_io_len code.
Avoiding max_io_len's split_io logic enables DM's discard support to
submit the entire discard request to a target. But discards must still
be split on target boundaries.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Rename __flush_target to __issue_target_request now that it is used to
issue both flush and discard requests.
Introduce __issue_target_requests as a convenient wrapper to
__issue_target_request 'num_flush_requests' or 'num_discard_requests'
times per target.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Allow discards to be passed through to linear mappings if at least one
underlying device supports it. Discards will be forwarded only to
devices that support them.
A target that supports discards should set num_discard_requests to
indicate how many times each discard request must be submitted to it.
Verify table's underlying devices support discards prior to setting the
associated DM device as capable of discards (via QUEUE_FLAG_DISCARD).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Joe Thornber <thornber@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Allocate cipher strings indpendently of struct crypt_config and move
cipher parsing and allocation into a separate function to prepare for
supporting the cryptoapi format e.g. "xts(aes)".
No functional change in this patch.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use just one label and reuse common destructor for crypt target.
Parse remaining argv arguments in logic order.
Also do not ignore error values from IV init and set key functions.
No functional change in this patch except changed return codes
based on above.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add devname:mapper/control and MAPPER_CTRL_MINOR module alias
to support dm-mod module autoloading.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Peter Rajnoha <prajnoha@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
'target_request_nr' is a more generic name that reflects the fact that
it will be used for both flush and discard support.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This change unifies the various checks and finalization that occurs on a
table prior to use. By doing so, it allows table construction without
traversing the dm-ioctl interface.
Signed-off-by: Will Drewry <wad@chromium.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Implement merge method for the snapshot origin to improve read
performance.
Without merge method, dm asks the upper layers to submit smallest possible
bios --- one page. Submitting such small bios impacts performance negatively
when reading or writing the origin device.
Without this patch, CPU consumption when reading the origin on lvm on md-raid0
was 6 to 12%, with this patch, it drops to 1 to 4%.
Note: in my testing, it actually degraded performance in some settings, I
traced it to Maxtor disks having problems with > 512-sector requests.
Reducing the number of sectors to /sys/block/sd*/queue/max_sectors_kb to
256 fixed the read performance. I think we don't have to care about weird
disks that actually degrade performance because of large requests being
sent to them.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Change bio-based mapped devices no longer to have a fully initialized
request_queue (request_fn, elevator, etc). This means bio-based DM
devices no longer register elevator sysfs attributes ('iosched/' tree
or 'scheduler' other than "none").
In contrast, a request-based DM device will continue to have a full
request_queue and will register elevator sysfs attributes. Therefore
a user can determine a DM device's type by checking if elevator sysfs
attributes exist.
First allocate a minimalist request_queue structure for a DM device
(needed for both bio and request-based DM).
Initialization of a full request_queue is deferred until it is known
that the DM device is request-based, at the end of the table load
sequence.
Factor DM device's request_queue initialization:
- common to both request-based and bio-based into dm_init_md_queue().
- specific to request-based into dm_init_request_based_queue().
The md->type_lock mutex is used to protect md->queue, in addition to
md->type, during table_load().
A DM device's first table_load will establish the immutable md->type.
But md->queue initialization, based on md->type, may fail at that time
(because blk_init_allocated_queue cannot allocate memory). Therefore
any subsequent table_load must (re)try dm_setup_md_queue independently of
establishing md->type.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Determine whether a mapped device is bio-based or request-based when
loading its first (inactive) table and don't allow that to be changed
later.
This patch performs different device initialisation in each of the two
cases. (We don't think it's necessary to add code to support changing
between the two types.)
Allowed md->type transitions:
DM_TYPE_NONE to DM_TYPE_BIO_BASED
DM_TYPE_NONE to DM_TYPE_REQUEST_BASED
We now prevent table_load from replacing the inactive table with a
conflicting type of table even after an explicit table_clear.
Introduce 'type_lock' into the struct mapped_device to protect md->type
and to prepare for the next patch that will change the queue
initialization and allocate memory while md->type_lock is held.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
drivers/md/dm-ioctl.c | 15 +++++++++++++++
drivers/md/dm.c | 37 ++++++++++++++++++++++++++++++-------
drivers/md/dm.h | 5 +++++
include/linux/dm-ioctl.h | 4 ++--
4 files changed, 52 insertions(+), 9 deletions(-)
When processing barriers, skip the second flush if processing the bio
failed with -EOPNOTSUPP. This can happen with discard+barrier requests.
If the device doesn't support discard, there would be two useless
SYNCHRONIZE CACHE commands. The first dm_flush cannot be so easily
optimized out, so we leave it there.
Previously, -EOPNOTSUPP could be received in dec_pending only with empty
barriers and we ignored that error, assuming the device not supporting
cache flushes has cache always consistent. With the addition of discard
barriers, this -EOPNOTSUPP can also be generated by discards and we
must record it in md->barrier_error for process_barrier.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch fixes hard-coded value for the size of a chunk that includes
disk header for persistent snapshot. It should be changed to existing
macro NUM_SNAPSHOT_HDR_CHUNKS instead of using hard-coded value 1.
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@jp.fujitsu.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use kstrdup when the goal of an allocation is copy a string into the
allocated region.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to;
expression flag,E1,E2;
statement S;
@@
- to = kmalloc(strlen(from) + 1,flag);
+ to = kstrdup(from, flag);
... when != \(from = E1 \| to = E1 \)
if (to==NULL || ...) S
... when != \(from = E2 \| to = E2 \)
- strcpy(to, from);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The dm control device does not implement read/write, so it has no use for
seeking. Using no_llseek prevents falling back to default_llseek, which
requires the BKL.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch separates the device deletion code from dm_put()
to make sure the deletion happens in the process context.
By this patch, device deletion always occurs in an ioctl (process)
context and dm_put() can be called in interrupt context.
As a result, the request-based dm's bad dm_put() usage pointed out
by Mikulas below disappears.
http://marc.info/?l=dm-devel&m=126699981019735&w=2
Without this patch, I confirmed there is a case to crash the system:
dm_put() => dm_table_destroy() => vfree() => BUG_ON(in_interrupt())
Some more backgrounds and details:
In request-based dm, a device opener can remove a mapped_device
while the last request is still completing, because bios in the last
request complete first and then the device opener can close and remove
the mapped_device before the last request completes:
CPU0 CPU1
=================================================================
<<INTERRUPT>>
blk_end_request_all(clone_rq)
blk_update_request(clone_rq)
bio_endio(clone_bio) == end_clone_bio
blk_update_request(orig_rq)
bio_endio(orig_bio)
<<I/O completed>>
dm_blk_close()
dev_remove()
dm_put(md)
<<Free md>>
blk_finish_request(clone_rq)
....
dm_end_request(clone_rq)
free_rq_clone(clone_rq)
blk_end_request_all(orig_rq)
rq_completed(md)
So request-based dm used dm_get()/dm_put() to hold md for each I/O
until its request completion handling is fully done.
However, the final dm_put() can call the device deletion code which
must not be run in interrupt context and may cause kernel panic.
To solve the problem, this patch moves the device deletion code,
dm_destroy(), to predetermined places that is actually deleting
the mapped_device in ioctl (process) context, and changes dm_put()
just to decrement the reference count of the mapped_device.
By this change, dm_put() can be used in any context and the symmetric
model below is introduced:
dm_create(): create a mapped_device
dm_destroy(): destroy a mapped_device
dm_get(): increment the reference count of a mapped_device
dm_put(): decrement the reference count of a mapped_device
dm_destroy() waits for all references of the mapped_device to disappear,
then deletes the mapped_device.
dm_destroy() uses active waiting with msleep(1), since deleting
the mapped_device isn't performance-critical task.
And since at this point, nobody opens the mapped_device and no new
reference will be taken, the pending counts are just for racing
completing activity and will eventually decrease to zero.
For the unlikely case of the forced module unload, dm_destroy_immediate(),
which doesn't wait and forcibly deletes the mapped_device, is also
introduced and used in dm_hash_remove_all(). Otherwise, "rmmod -f"
may be stuck and never return.
And now, because the mapped_device is deleted at this point, subsequent
accesses to the mapped_device may cause NULL pointer references.
Cc: stable@kernel.org
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch changes dm_hash_remove_all() to release _hash_lock when
removing a device. After removing the device, dm_hash_remove_all()
takes _hash_lock and searches the hash from scratch again.
This patch is a preparation for the next patch, which changes device
deletion code to wait for md reference to be 0. Without this patch,
the wait in the next patch may cause AB-BA deadlock:
CPU0 CPU1
-----------------------------------------------------------------------
dm_hash_remove_all()
down_write(_hash_lock)
table_status()
md = find_device()
dm_get(md)
<increment md->holders>
dm_get_live_or_inactive_table()
dm_get_inactive_table()
down_write(_hash_lock)
<in the md deletion code>
<wait for md->holders to be 0>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch prevents access to mapped_device which is being deleted.
Currently, even after a mapped_device has been removed from the hash,
it could be accessed through idr_find() using minor number.
That could cause a race and NULL pointer reference below:
CPU0 CPU1
------------------------------------------------------------------
dev_remove(param)
down_write(_hash_lock)
dm_lock_for_deletion(md)
spin_lock(_minor_lock)
set_bit(DMF_DELETING)
spin_unlock(_minor_lock)
__hash_remove(hc)
up_write(_hash_lock)
dev_status(param)
md = find_device(param)
down_read(_hash_lock)
__find_device_hash_cell(param)
dm_get_md(param->dev)
md = dm_find_md(dev)
spin_lock(_minor_lock)
md = idr_find(MINOR(dev))
spin_unlock(_minor_lock)
dm_put(md)
free_dev(md)
dm_get(md)
up_read(_hash_lock)
__dev_status(md, param)
dm_put(md)
This patch fixes such problems.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
All the dm ioctls that generate uevents set the DM_UEVENT_GENERATED flag so
that userspace knows whether or not to wait for a uevent to be processed
before continuing,
The dm rename ioctl sets this flag but was not structured to return it
to userspace. This patch restructures the rename ioctl processing to
behave like the other ioctls that return data and so fix this.
Signed-off-by: Peter Rajnoha <prajnoha@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove useless __dev_status call while processing an ioctl that sets up
device geometry and target message. The data is not returned to
userspace so there is no point collecting it and in the case of
target_message it is collected before processing the message so if it
did return it might be stale.
Signed-off-by: Peter Rajnoha <prajnoha@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Validate chunk size against both origin and snapshot sector size
Don't allow chunk size smaller than either origin or snapshot logical
sector size. Reading or writing data not aligned to sector size is not
allowed and causes immediate errors.
This requires us to open the origin before initialising the
exception store and to export dm_snap_origin.
Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Iterate both origin and snapshot devices
iterate_devices method should call the callback for all the devices where
the bio may be remapped. Thus, snapshot_iterate_devices should call the callback
for both snapshot and origin underlying devices because it remaps some bios
to the snapshot and some to the origin.
snapshot_iterate_devices called the callback only for the origin device.
This led to badly calculated device limits if snapshot and origin were placed
on different types of disks.
Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
multipath_ctr() forgets to return an error after detecting
missing path parameters. Fix this.
Signed-off-by: Patrick LoPresti <lopresti@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
* 'for-linus' of git://neil.brown.name/md: (24 commits)
md: clean up do_md_stop
md: fix another deadlock with removing sysfs attributes.
md: move revalidate_disk() back outside open_mutex
md/raid10: fix deadlock with unaligned read during resync
md/bitmap: separate out loading a bitmap from initialising the structures.
md/bitmap: prepare for storing write-intent-bitmap via dm-dirty-log.
md/bitmap: optimise scanning of empty bitmaps.
md/bitmap: clean up plugging calls.
md/bitmap: reduce dependence on sysfs.
md/bitmap: white space clean up and similar.
md/raid5: export raid5 unplugging interface.
md/plug: optionally use plugger to unplug an array during resync/recovery.
md/raid5: add simple plugging infrastructure.
md/raid5: export is_congested test
raid5: Don't set read-ahead when there is no queue
md: add support for raising dm events.
md: export various start/stop interfaces
md: split out md_rdev_init
md: be more careful setting MD_CHANGE_CLEAN
md/raid5: ensure we create a unique name for kmem_cache when mddev has no gendisk
...
There is only one error exit from do_md_stop, so make that more
explicit and discard the 'err' variable.
Also drop the 'revalidate' variable by moving the unlock calls around.
Signed-off-by: NeilBrown <neilb@suse.de>
Move the deletion of sysfs attributes from reconfig_mutex to
open_mutex didn't really help as a process can try to take
open_mutex while holding reconfig_mutex, so the same deadlock can
happen, just requiring one more process to be involved in the chain.
I looks like I cannot easily use locking to wait for the sysfs
deletion to complete, so don't.
The only things that we cannot do while the deletions are still
pending is other things which can change the sysfs namespace: run,
takeover, stop. Each of these can fail with -EBUSY.
So set a flag while doing a sysfs deletion, and fail run, takeover,
stop if that flag is set.
This is suitable for 2.6.35.x
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Commit b821eaa5 "md: remove ->changed and related code" moved
revalidate_disk() under open_mutex, and lockdep noticed.
[ INFO: possible circular locking dependency detected ]
2.6.32-mdadm-locking #1
-------------------------------------------------------
mdadm/3640 is trying to acquire lock:
(&bdev->bd_mutex){+.+.+.}, at: [<ffffffff811acecb>] revalidate_disk+0x5b/0x90
but task is already holding lock:
(&mddev->open_mutex){+.+...}, at: [<ffffffffa055e07a>] do_md_stop+0x4a/0x4d0 [md_mod]
which lock already depends on the new lock.
It is suitable for 2.6.35.x
Cc: <stable@kernel.org>
Reported-by: Przemyslaw Czarnowski <przemyslaw.hawrylewicz.czarnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The open and release block_device_operations are currently
called with the BKL held. In order to change that, we must
first make sure that all drivers that currently rely
on this have no regressions.
This blindly pushes the BKL into all .open and .release
operations for all block drivers to prepare for the
next step. The drivers can subsequently replace the BKL
with their own locks or remove it completely when it can
be shown that it is not needed.
The functions blkdev_get and blkdev_put are the only
remaining users of the big kernel lock in the block
layer, besides a few uses in the ioctl code, none
of which need to serialize with blkdev_{get,put}.
Most of these two functions is also under the protection
of bdev->bd_mutex, including the actual calls to
->open and ->release, and the common code does not
access any global data structures that need the BKL.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Remove the current bio flags and reuse the request flags for the bio, too.
This allows to more easily trace the type of I/O from the filesystem
down to the block driver. There were two flags in the bio that were
missing in the requests: BIO_RW_UNPLUG and BIO_RW_AHEAD. Also I've
renamed two request flags that had a superflous RW in them.
Note that the flags are in bio.h despite having the REQ_ name - as
blkdev.h includes bio.h that is the only way to go for now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Remove all the trivial wrappers for the cmd_type and cmd_flags fields in
struct requests. This allows much easier grepping for different request
types instead of unwinding through macros.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
If the 'bio_split' path in raid10-read is used while
resync/recovery is happening it is possible to deadlock.
Fix this be elevating ->nr_waiting for the duration of both
parts of the split request.
This fixes a bug that has been present since 2.6.22
but has only started manifesting recently for unknown reasons.
It is suitable for and -stable since then.
Reported-by: Justin Bronder <jsbronder@gentoo.org>
Tested-by: Justin Bronder <jsbronder@gentoo.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
dm makes this distinction between ->ctr and ->resume, so we need to
too.
Also get the new bitmap_load to clear out the bitmap first, as this is
most consistent with the dm suspend/resume approach
Signed-off-by: NeilBrown <neilb@suse.de>
This allows md/raid5 to fully work as a dm target.
Normally md uses a 'filemap' which contains a list of pages of bits
each of which may be written separately.
dm-log uses and all-or-nothing approach to writing the log, so
when using a dm-log, ->filemap is NULL and the flags normally stored
in filemap_attr are stored in ->logattrs instead.
Signed-off-by: NeilBrown <neilb@suse.de>
A bitmap is stored as one page per 2048 bits.
If none of the bits are set, the page is not allocated.
When bitmap_get_counter finds that a page isn't allocate,
it just reports that one bit work of space isn't flagged,
rather than reporting that 2048 bits worth of space are
unflagged.
This can cause searches for flagged bits (e.g. bitmap_close_sync)
to do more work than is really necessary.
So change bitmap_get_counter (when creating) to report a number of
blocks that more accurately reports the range of the device for which
no counter currently exists.
Signed-off-by: NeilBrown <neilb@suse.de>
1/ use md_unplug in bitmap.c as we will soon be using bitmaps under
arrays with no queue attached.
2/ Don't bother plugging the queue when we set a bit in the bitmap.
The reason for this was to encourage as many bits as possible to
get set before we unplug and write stuff out.
However every personality already plugs the queue after
bitmap_startwrite either directly (raid1/raid10) or be setting
STRIPE_BIT_DELAY which causes the queue to be plugged later
(raid5).
Signed-off-by: NeilBrown <neilb@suse.de>
For dm-raid45 we will want to use bitmaps in dm-targets which don't
have entries in sysfs, so cope with the mddev not living in sysfs.
Signed-off-by: NeilBrown <neilb@suse.de>
Fixes some whitespace problems
Fixed some checkpatch.pl complaints.
Replaced kmalloc ... memset(0), with kzalloc
Fixed an unlikely memory leak on an error path.
Reformatted a number of 'if/else' sets, sometimes
replacing goto with an else clause.
Removed some old comments and commented-out code.
Signed-off-by: NeilBrown <neilb@suse.de>
If an array doesn't have a 'queue' then md_do_sync cannot
unplug it.
In that case it will have a 'plugger', so make that available
to the mddev, and use it to unplug the array if needed.
Signed-off-by: NeilBrown <neilb@suse.de>
md/raid5 uses the plugging infrastructure provided by the block layer
and 'struct request_queue'. However when we plug raid5 under dm there
is no request queue so we cannot use that.
So create a similar infrastructure that is much lighter weight and use
it for raid5.
Signed-off-by: NeilBrown <neilb@suse.de>
the dm module will need this for dm-raid45.
Also only access ->queue->backing_dev_info->congested_fn
if ->queue actually exists. It won't in a dm target.
Signed-off-by: NeilBrown <neilb@suse.de>
dm-raid456 does not provide a 'queue' for raid5 to use,
so we must make raid5 stop depending on the queue.
First: read_ahead
dm handles read-ahead adjustment fully in userspace, so
simply don't do any readahead adjustments if there is
no queue.
Also re-arrange code slightly so all the accesses to ->queue are
together.
Finally, move the blk_queue_merge_bvec function into the 'if' as
the ->split_io setting in dm-raid456 has the same effect.
Signed-off-by: NeilBrown <neilb@suse.de>
dm uses scheduled work to raise events to user-space.
So allow md device to have work_structs and schedule them on an error.
Signed-off-by: NeilBrown <neilb@suse.de>
export entry points for starting and stopping md arrays.
This will be used by a module to make md/raid5 work under
dm.
Also stop calling md_stop_writes from md_stop, as that won't
work well with dm - it will want to call the two separately.
Signed-off-by: NeilBrown <neilb@suse.de>
This functionality will be needed separately in a subsequent patch, so
split it into it's own exported function.
Signed-off-by: NeilBrown <neilb@suse.de>
When MD_CHANGE_CLEAN is set we might block in md_write_start.
So we should only set it when fairly sure that something will clear
it.
There are two places where it is set so as to encourage a metadata
update to record the progress of resync/recovery. This should only
be done if the internal metadata update mechanisms are in use, which
can be tested by by inspecting '->persistent'.
Signed-off-by: NeilBrown <neilb@suse.de>
We will shortly allow md devices with no gendisk (they are attached to
a dm-target instead). That will cause mdname() to return 'mdX'.
There is one place where mdname really needs to be unique: when
creating the name for a slab cache.
So in that case, if there is no gendisk, you the address of the mddev
formatted in HEX to provide a unique name.
Signed-off-by: NeilBrown <neilb@suse.de>
We will want md devices to live as dm targets where sysfs is not
visible. So allow md to not connect to sysfs.
Signed-off-by: NeilBrown <neilb@suse.de>
There are few situations where it would make any sense to add a spare
when reducing the number of devices in an array, but it is
conceivable: A 6 drive RAID6 with two missing devices could be
reshaped to a 5 drive RAID6, and a spare could become available
just in time for the reshape, but not early enough to have been
recovered first. 'freezing' recovery can make this easy to
do without any races.
However doing such a thing is a bad idea. md will not record the
partially-recovered state of the 'spare' and when the reshape
finished it will think that the spare is still spare.
Easiest way to avoid this confusion is to simply disallow it.
Signed-off-by: NeilBrown <neilb@suse.de>
As the comment says, the tail of this loop only applies to devices
that are not fully in sync, so if In_sync was set, we should avoid
the rest of the loop.
This bug will hardly ever cause an actual problem. The worst it
can do is allow an array to be assembled that is dirty and degraded,
which is not generally a good idea (without warning the sysadmin
first).
This will only happen if the array is RAID4 or a RAID5/6 in an
intermediate state during a reshape and so has one drive that is
all 'parity' - no data - while some other device has failed.
This is certainly possible, but not at all common.
Signed-off-by: NeilBrown <neilb@suse.de>
During a recovery of reshape the early part of some devices might be
in-sync while the later parts are not.
We we know we are looking at an early part it is good to treat that
part as in-sync for stripe calculations.
This is particularly important for a reshape which suffers device
failure. Treating the data as in-sync can mean the difference between
data-safety and data-loss.
Signed-off-by: NeilBrown <neilb@suse.de>
When we are reshaping an array, the device failure combinations
that cause us to decide that the array as failed are more subtle.
In particular, any 'spare' will be fully in-sync in the section
of the array that has already been reshaped, thus failures that
affect only that section are less critical.
So encode this subtlety in a new function and call it as appropriate.
The case that showed this problem was a 4 drive RAID5 to 8 drive RAID6
conversion where the last two devices failed.
This resulted in:
good good good good incomplete good good failed failed
while converting a 5-drive RAID6 to 8 drive RAID5
The incomplete device causes the whole array to look bad,
bad as it was actually good for the section that had been
converted to 8-drives, all the data was actually safe.
Reported-by: Terry Morris <tbmorris@tbmorris.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When an array is reshaped to have fewer devices, the reshape proceeds
from the end of the devices to the beginning.
If a device happens to be non-In_sync (which is possible but rare)
we would normally update the ->recovery_offset as the reshape
progresses. However that would be wrong as the recover_offset records
that the early part of the device is in_sync, while in fact it would
only be the later part that is in_sync, and in any case the offset
number would be measured from the wrong end of the device.
Relatedly, if after a reshape a spare is discovered to not be
recoverred all the way to the end, not allow spare_active
to incorporate it in the array.
This becomes relevant in the following sample scenario:
A 4 drive RAID5 is converted to a 6 drive RAID6 in a combined
operation.
The RAID5->RAID6 conversion will cause a 5 drive to be included as a
spare, then the 5drive -> 6drive reshape will effectively rebuild that
spare as it progresses. The 6th drive is treated as in_sync the whole
time as there is never any case that we might consider reading from
it, but must not because there is no valid data.
If we interrupt this reshape part-way through and reverse it to return
to a 5-drive RAID6 (or event a 4-drive RAID5), we don't want to update
the recovery_offset - as that would be wrong - and we don't want to
include that spare as active in the 5-drive RAID6 when the reversed
reshape completed and it will be mostly out-of-sync still.
Signed-off-by: NeilBrown <neilb@suse.de>
The entries in the stripe_cache maintained by raid5 are enlarged
when we increased the number of devices in the array, but not
shrunk when we reduce the number of devices.
So if entries are added after reducing the number of devices, we
much ensure to initialise the whole entry, not just the part that
is currently relevant. Otherwise if we enlarge the array again,
we will reference uninitialised values.
As grow_buffers/shrink_buffer now want to use a count that is stored
explicity in the raid_conf, they should get it from there rather than
being passed it as a parameter.
Signed-off-by: NeilBrown <neilb@suse.de>
Only level 5 with layout=PARITY_N can be taken over to raid0 now.
Lets allow level 4 either.
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
After takeover from raid5/10 -> raid0 mddev->layout is not cleared.
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Use mddev->new_layout in setup_conf.
Also use new_chunk, and don't set ->degraded in takeover(). That
gets set in run()
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Most array level changes leave the list of devices largely unchanged,
possibly causing one at the end to become redundant.
However conversions between RAID0 and RAID10 need to renumber
all devices (except 0).
This renumbering is currently being done in the ->run method when the
new personality takes over. However this is too late as the common
code in md.c might already have invalidated some of the devices if
they had a ->raid_disk number that appeared to high.
Moving it into the ->takeover method is too early as the array is
still active at that time and wrong ->raid_disk numbers could cause
confusion.
So add a ->new_raid_disk field to mdk_rdev_s and use it to communicate
the new raid_disk number.
Now the common code knows exactly which devices need to be renumbered,
and which can be invalidated, and can do it all at a convenient time
when the array is suspend.
It can also update some symlinks in sysfs which previously were not be
updated correctly.
Reported-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Such NULL pointer dereference can occur when the driver was fixing the
read errors/bad blocks and the disk was physically removed
causing a system crash. This patch check if the
rcu_dereference() returns valid rdev before accessing it in fix_read_error().
Cc: stable@kernel.org
Signed-off-by: Prasanna S. Panchamukhi <prasanna.panchamukhi@riverbed.com>
Signed-off-by: Rob Becker <rbecker@riverbed.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Commit b821eaa572 broke partition
detection for md arrays.
The logic was almost right. However if revalidate_disk is called
when the device is not yet open, bdev->bd_disk won't be set, so the
flush_disk() Call will not set bd_invalidated.
So when md_open is called we still need to ensure that
->bd_invalidated gets set. This is easily done with a call to
check_disk_size_change in the place where the offending commit removed
check_disk_change. At the important times, the size will have changed
from 0 to non-zero, so check_disk_size_change will set bd_invalidated.
Tested-by: Duncan <1i5t5.duncan@cox.net>
Reported-by: Duncan <1i5t5.duncan@cox.net>
Signed-off-by: NeilBrown <neilb@suse.de>
By the previous modification, the cpu notifier can return encapsulate
errno value. This converts the cpu notifiers for raid5.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (69 commits)
fix handling of offsets in cris eeprom.c, get rid of fake on-stack files
get rid of home-grown mutex in cris eeprom.c
switch ecryptfs_write() to struct inode *, kill on-stack fake files
switch ecryptfs_get_locked_page() to struct inode *
simplify access to ecryptfs inodes in ->readpage() and friends
AFS: Don't put struct file on the stack
Ban ecryptfs over ecryptfs
logfs: replace inode uid,gid,mode initialization with helper function
ufs: replace inode uid,gid,mode initialization with helper function
udf: replace inode uid,gid,mode init with helper
ubifs: replace inode uid,gid,mode initialization with helper function
sysv: replace inode uid,gid,mode initialization with helper function
reiserfs: replace inode uid,gid,mode initialization with helper function
ramfs: replace inode uid,gid,mode initialization with helper function
omfs: replace inode uid,gid,mode initialization with helper function
bfs: replace inode uid,gid,mode initialization with helper function
ocfs2: replace inode uid,gid,mode initialization with helper function
nilfs2: replace inode uid,gid,mode initialization with helper function
minix: replace inode uid,gid,mode init with helper
ext4: replace inode uid,gid,mode init with helper
...
Trivial conflict in fs/fs-writeback.c (mark bitfields unsigned)
Conflicts:
drivers/md/md.c
- Resolved conflict in md_update_sb
- Added extra 'NULL' arg to new instance of sysfs_get_dirent.
Signed-off-by: NeilBrown <neilb@suse.de>
Now that the last user passing a NULL file pointer is gone we can remove
the redundant dentry argument and associated hacks inside vfs_fsynmc_range.
The next step will be removig the dentry argument from ->fsync, but given
the luck with the last round of method prototype changes I'd rather
defer this until after the main merge window.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The problem. When implementing a network namespace I need to be able
to have multiple network devices with the same name. Currently this
is a problem for /sys/class/net/*, /sys/devices/virtual/net/*, and
potentially a few other directories of the form /sys/ ... /net/*.
What this patch does is to add an additional tag field to the
sysfs dirent structure. For directories that should show different
contents depending on the context such as /sys/class/net/, and
/sys/devices/virtual/net/ this tag field is used to specify the
context in which those directories should be visible. Effectively
this is the same as creating multiple distinct directories with
the same name but internally to sysfs the result is nicer.
I am calling the concept of a single directory that looks like multiple
directories all at the same path in the filesystem tagged directories.
For the networking namespace the set of directories whose contents I need
to filter with tags can depend on the presence or absence of hotplug
hardware or which modules are currently loaded. Which means I need
a simple race free way to setup those directories as tagged.
To achieve a reace free design all tagged directories are created
and managed by sysfs itself.
Users of this interface:
- define a type in the sysfs_tag_type enumeration.
- call sysfs_register_ns_types with the type and it's operations
- sysfs_exit_ns when an individual tag is no longer valid
- Implement mount_ns() which returns the ns of the calling process
so we can attach it to a sysfs superblock.
- Implement ktype.namespace() which returns the ns of a syfs kobject.
Everything else is left up to sysfs and the driver layer.
For the network namespace mount_ns and namespace() are essentially
one line functions, and look to remain that.
Tags are currently represented a const void * pointers as that is
both generic, prevides enough information for equality comparisons,
and is trivial to create for current users, as it is just the
existing namespace pointer.
The work needed in sysfs is more extensive. At each directory
or symlink creating I need to check if the directory it is being
created in is a tagged directory and if so generate the appropriate
tag to place on the sysfs_dirent. Likewise at each symlink or
directory removal I need to check if the sysfs directory it is
being removed from is a tagged directory and if so figure out
which tag goes along with the name I am deleting.
Currently only directories which hold kobjects, and
symlinks are supported. There is not enough information
in the current file attribute interfaces to give us anything
to discriminate on which makes it useless, and there are
no potential users which makes it an uninteresting problem
to solve.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Devices which know that they are spares do not really need to have
an event count that matches the rest of the array, so there are no
data-in-sync issues. It is enough that the uuid matches.
So remove the requirement that the event count is up-to-date.
We currently still write out and event count on spares, but this
allows us in a year or 3 to stop doing that completely.
Signed-off-by: NeilBrown <neilb@suse.de>
When updating the event count for a simple clean <-> dirty transition,
we try to avoid updating the spares so they can safely spin-down.
As the event_counts across an array must be +/- 1, this means
decrementing the event_count on a dirty->clean transition.
This is not always safe and we have to avoid the unsafe time.
We current do this with a misguided idea about it being safe or
not depending on whether the event_count is odd or even. This
approach only works reliably in a few common instances, but easily
falls down.
So instead, simply keep internal state concerning whether it is safe
or not, and always assume it is not safe when an array is first
assembled.
Signed-off-by: NeilBrown <neilb@suse.de>
Fix: Raid-6 was not trying to correct a read-error when in
singly-degraded state and was instead dropping one more device, going to
doubly-degraded state. This patch fixes this behaviour.
Tested-by: Janos Haar <janos.haar@netcenter.hu>
Signed-off-by: Gabriele A. Trombetti <g.trombetti.lkrnl1213@logicschema.com>
Reported-by: Janos Haar <janos.haar@netcenter.hu>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
Some time ago we stopped the clean/active metadata updates
from being written to a 'spare' device in most cases so that
it could spin down and say spun down. Device failure/removal
etc are still recorded on spares.
However commit 51d5668cb2 broke this 50% of the time,
depending on whether the event count is even or odd.
The change log entry said:
This means that the alignment between 'odd/even' and
'clean/dirty' might take a little longer to attain,
how ever the code makes no attempt to create that alignment, so it
could take arbitrarily long.
So when we find that clean/dirty is not aligned with odd/even,
force a second metadata-update immediately. There are already cases
where a second metadata-update is needed immediately (e.g. when a
device fails during the metadata update). We just piggy-back on that.
Reported-by: Joe Bryant <tenminjoe@yahoo.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
read_balance uses a "unsigned long" for a sector number which
will get truncated beyond 2TB.
This will cause read-balancing to be non-optimal, and can cause
data to be read from the 'wrong' branch during a resync. This has a
very small chance of returning wrong data.
Reported-by: Jordan Russell <jr-list-2010@quo.to>
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Many 'printk' messages from the raid456 module mention 'raid5' even
though it may be a 'raid6' or even 'raid4' array. This can cause
confusion.
Also the actual array name is not always reported and when it is
it is not reported consistently.
So change all the messages to start:
md/raid:%s:
where '%s' becomes e.g. md3 to identify the particular array.
Signed-off-by: NeilBrown <neilb@suse.de>
RAID10 has been available for quite a while now and is quite well
tested, so we can remove the EXPERIMENTAL designation.
Reported-by: Eric MSP Veith <eveith@wwweb-library.net>
Signed-off-by: NeilBrown <neilb@suse.de>
Level modifications change the output of mdstat. The mdmon manager
thread is interested in these events for external metadata management.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When a raid1 array is configured to support write-behind
on some devices, it normally only reads from other devices.
If all devices are write-behind (because the rest have failed)
it is possible for a read request to be serviced before a
behind-write request, which would appear as data corruption.
So when forced to read from a WriteMostly device, wait for any
write-behind to complete, and don't start any more behind-writes.
Signed-off-by: NeilBrown <neilb@suse.de>
This message seems to suggest the named device is the one on which a
read failed, however it is actually the device that the read will be
redirected to.
So make the message a little clearer.
Reported-by: Tim Burgess <ozburgess@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This is
- unnecessary because mddev_suspend is always followed by a call to
->stop, and each ->stop unregisters the thread, and
- a problem as it makes it awkwards to suspend and then resume a
device as we will want later.
Signed-off-by: NeilBrown <neilb@suse.de>
We used to pass the personality make_request function direct
to the block layer so the first argument had to be a queue.
But now we have the intermediary md_make_request so it makes
at lot more sense to pass a struct mddev_s.
It makes it possible to have an mddev without its own queue too.
Signed-off-by: NeilBrown <neilb@suse.de>
This moves the call to the other side of set_readonly, but that should
not be an issue.
This encapsulates in 'md_stop' all of the functionality for internally
stopping the array, leaving all the interactions with externalities
(sysfs, request_queue, gendisk) in do_md_stop.
Signed-off-by: NeilBrown <neilb@suse.de>
Using do_md_stop to set an array to read-only is a little confusing.
Now most of the common code has been factored out, split
md_set_readonly off in to a separate function.
Signed-off-by: NeilBrown <neilb@suse.de>
Further refactoring of do_md_stop.
This one requires some explanation as it takes code from different
places in do_md_stop, so some re-ordering happens.
We only get into this part of do_md_stop if there are no active opens
of the device, so no writes can be happening and the device must have
been flushed. In md_stop_writes we want to stop any internal sources
of writes - i.e. resync - and flush out the metadata.
The only code that was previously before some of this code is
code to clean up the queue, the mddev, the gendisk, or sysfs, all
of which is probably better after code that makes active changes (i.e.
triggers writes).
Signed-off-by: NeilBrown <neilb@suse.de>
do_md_stop is large and clunky, so hard to understand.
This is a first step of refactoring, pulling two simple
sub-functions out.
Signed-off-by: NeilBrown <neilb@suse.de>
As part of relaxing the binding between an mddev and gendisk,
we separate do_md_run into two functions.
md_run does all the work internal to md
do_md_run calls md_run and makes and changes to gendisk
that are required.
Signed-off-by: NeilBrown <neilb@suse.de>
We set ->changed to 1 and call check_disk_change at the end
of md_open so that bd_invalidated would be set and thus
partition rescan would happen appropriately.
Now that we call revalidate_disk directly, which sets bd_invalidates,
that indirection is no longer needed and can be removed.
Signed-off-by: NeilBrown <neilb@suse.de>
Using ->array_sectors rather than get_capacity() is more
direct and is a step towards relaxing the tight connection
between mddev and gendisk.
Signed-off-by: NeilBrown <neilb@suse.de>
While I generally prefer letting personalities do as much as possible,
given that we have a central md_make_request anyway we may as well use
it to simplify code.
Also this centralises knowledge of ->gendisk which will help later.
Signed-off-by: NeilBrown <neilb@suse.de>
Diving through ->queue to find mddev is unnecessarily complex - there
is an easier path to finding mddev, so use that.
Signed-off-by: NeilBrown <neilb@suse.de>
Level changes can be very significant, so make sure
to notify them via sysfs.
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When metadata is being managed by user-space, md doesn't know
what the maximum number of devices allowed in an array is
so ->max_disks is 0. In this case we should allow any (+ve)
number of disks.
Signed-off-by: NeilBrown <neilb@suse.de>
Writing "none" to "../md/dev-xx/slot" removes that device
from being an active part of the array, but it didn't
set ->raid_disk to -1 to record this fact.
Signed-off-by: Maciej Trela <Maciej.Trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
In a subsequent patch we will make it possible to change
mddev->raid_disks while a RAID0 or RAID10 array is active. This is
part of the process of reshaping such an array.
This means that we cannot use this value while processes requests
(it is OK to use it during initialisation as we are locked against
changes then).
Both RAID0 and RAID10 have the same value stored in the private data
structure, so use that value instead.
Signed-off-by: NeilBrown <neilb@suse.de>
This was needed when sysfs files could only be 'notified'
from process context. Now that we have sys_notify_direct,
we can call it directly from an interrupt.
Signed-off-by: NeilBrown <neilb@suse.de>
void pointers do not need to be cast to other pointer types.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Keep track of the maximum number of concurrent write-behind requests
for an md array and exposed this number in sysfs at
md/bitmap/max_backlog_used
Writing any value to this file will clear it.
This allows userspace to be involved in tuning bitmap/backlog.
Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: NeilBrown <neilb@suse.de>
These fields have never been used.
commit 4b6d287f62
added them, but also added identical files to bitmap_super_s,
and only used the latter.
So remove these unused fields.
Signed-off-by: NeilBrown <neilb@suse.de>
There is a very small race window when writing to a
RAID1 such that if a device is marked faulty at exactly the wrong
time, the write-in-progress will not be sent to the device,
but the bitmap (if present) will be updated to say that
the write was sent.
Then if the device turned out to still be usable as was re-added
to the array, the bitmap-based-resync would skip resyncing that
block, possibly leading to corruption. This would only be a problem
if no further writes were issued to that area of the device (i.e.
that bitmap chunk).
Suitable for any pending -stable kernel.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Some levels expect the 'redundancy group' to be present,
others don't.
So when we change level of an array we might need to
add or remove this group.
This requires fixing up the current practice of overloading ->private
to indicate (when ->pers == NULL) that something needs to be removed.
So create a new ->to_remove to fill that role.
When changing levels, we may need to add or remove attributes. When
changing RAID5 -> RAID6, we both add and remove the same thing. It is
important to catch this and optimise it out as the removal is delayed
until a lock is released, so trying to add immediately would cause
problems.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
When an array is stopped we need to remove some
sysfs files which are dependent on the type of array.
We need to delay that deletion as deleting them while holding
reconfig_mutex can lead to deadlocks.
We currently delay them until the array is completely destroyed.
However it is possible to deactivate and then reactivate the array.
It is also possible to need to remove sysfs files when changing level,
which can potentially happen several times before an array is
destroyed.
So we need to delete these files more promptly: as soon as
reconfig_mutex is dropped.
We need to ensure this happens before do_md_run can restart the array,
so we use open_mutex for some extra locking. This is not deadlock
prone.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Since commit ef286f6fa6
it has been important that each personality clears
->private in the ->stop() function, or sets it to a
attribute group to be removed.
linear.c doesn't. This can sometimes lead to an oops,
though it doesn't always.
Suitable for 2.6.33-stable and 2.6.34.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
When the user sets the block device to readwrite then the mddev should
follow suit. Otherwise, the BUG_ON in md_write_start() will be set to
trigger.
The reverse direction, setting mddev->ro to match a set readonly
request, can be ignored because the blkdev level readonly flag precludes
the need to have mddev->ro set correctly. Nevermind the fact that
setting mddev->ro to 1 may fail if the array is in use.
Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Some time ago we stopped the clean/active metadata updates
from being written to a 'spare' device in most cases so that
it could spin down and say spun down. Device failure/removal
etc are still recorded on spares.
However commit 51d5668cb2 broke this 50% of the time,
depending on whether the event count is even or odd.
The change log entry said:
This means that the alignment between 'odd/even' and
'clean/dirty' might take a little longer to attain,
how ever the code makes no attempt to create that alignment, so it
could take arbitrarily long.
So when we find that clean/dirty is not aligned with odd/even,
force a second metadata-update immediately. There are already cases
where a second metadata-update is needed immediately (e.g. when a
device fails during the metadata update). We just piggy-back on that.
Reported-by: Joe Bryant <tenminjoe@yahoo.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
Fix: Raid-6 was not trying to correct a read-error when in
singly-degraded state and was instead dropping one more device, going to
doubly-degraded state. This patch fixes this behaviour.
Tested-by: Janos Haar <janos.haar@netcenter.hu>
Signed-off-by: Gabriele A. Trombetti <g.trombetti.lkrnl1213@logicschema.com>
Reported-by: Janos Haar <janos.haar@netcenter.hu>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
Previous patch changes stripe and chunk_number to sector_t but
mistakenly did not update all of the divisions to use sector_dev().
This patch changes all the those divisions (actually the '%' operator)
to sector_div.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
With many large drives and small chunk sizes it is possible
to create a RAID5 with more than 2^31 chunks. Make sure this
works.
Reported-by: Brett King <king.br@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
If a component device has a merge_bvec_fn then as we never call it
we must ensure we never need to. Currently this is done by setting
max_sector to 1 PAGE, however this does not stop a bio being created
with several sub-page iovecs that would violate the merge_bvec_fn.
So instead set max_segments to 1 and set the segment boundary to the
same as a page boundary to ensure there is only ever one single-page
segment of IO requested at a time.
This can particularly be an issue when 'xen' is used as it is
known to submit multiple small buffers in a single bio.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
Constify struct sysfs_ops.
This is part of the ops structure constification
effort started by Arjan van de Ven et al.
Benefits of this constification:
* prevents modification of data that is shared
(referenced) by many other structure instances
at runtime
* detects/prevents accidental (but not intentional)
modification attempts on archs that enforce
read-only kernel data at runtime
* potentially better optimized code as the compiler
can assume that the const data cannot be changed
* the compiler/linker move const data into .rodata
and therefore exclude them from false sharing
Signed-off-by: Emese Revfy <re.emese@gmail.com>
Acked-by: David Teigland <teigland@redhat.com>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To prevent deadlock, bios in the hold list should be flushed before
dm_rh_stop_recovery() is called in mirror_suspend().
The recovery can't start because there are pending bios and therefore
dm_rh_stop_recovery deadlocks.
When there are pending bios in the hold list, the recovery waits for
the completion of the bios after recovery_count is acquired.
The recovery_count is released when the recovery finished, however,
the bios in the hold list are processed after dm_rh_stop_recovery() in
mirror_presuspend(). dm_rh_stop_recovery() also acquires recovery_count,
then deadlock occurs.
Signed-off-by: Takahiro Yasui <tyasui@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Eliminate a 4-byte hole in 'struct dm_io_memory' by moving 'offset' above the
'ptr' to which it applies (size reduced from 24 to 16 bytes). And by
association, 1-4 byte hole is eliminated in 'struct dm_io_request' (size
reduced from 56 to 48 bytes).
Eliminate all 6 4-byte holes and 1 cache-line in 'struct dm_snapshot' (size
reduced from 392 to 368 bytes).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Set a new DM_UEVENT_GENERATED_FLAG when returning from ioctls to
indicate that a uevent was actually generated. This tells the userspace
caller that it may need to wait for the event to be processed.
Signed-off-by: Peter Rajnoha <prajnoha@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Free the dm_io structure before calling bio_endio() instead of after it,
to ensure that the io_pool containing it is not referenced after it is
freed.
This partially fixes a problem described here
https://www.redhat.com/archives/dm-devel/2010-February/msg00109.html
thread 1:
bio_endio(bio, io_error);
/* scheduling happens */
thread 2:
close the device
remove the device
thread 1:
free_io(md, io);
Thread 2, when removing the device, sees non-empty md->io_pool (because the
io hasn't been freed by thread 1 yet) and may crash with BUG in mempool_free.
Thread 1 may also crash, when freeing into a nonexisting mempool.
To fix this we must make sure that bio_endio() is the last call and
the md structure is not accessed afterwards.
There is another bio_endio in process_barrier, but it is called from the thread
and the thread is destroyed prior to freeing the mempools, so this call is
not affected by the bug.
A similar bug exists with module unloads - the module may be unloaded
immediately after bio_endio - but that is more difficult to fix.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove unused parameters(start and len) of dm_get_device()
and fix the callers.
Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Only issue a uevent on a resume if the state of the device changed,
i.e. if it was suspended and/or its table was replaced.
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If all mirror legs fail, always return an error instead of holding the
bio, even if the handle_errors option was set. At present it is the
responsibility of the driver underneath us to deal with retries,
multipath etc.
The patch adds the bio to the failures list instead of holding it
directly. do_failures tests first if all legs failed and, if so,
returns the bio with -EIO. If any leg is still alive and handle_errors
is set, do_failures calls hold_bio.
Reviewed-by: Takahiro Yasui <tyasui@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch pulls the pg_init path activation code out of
process_queued_ios() into a new function.
No functional change.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
When suspending the device we must wait for all I/O to complete, but
pg-init may be still in progress even after flushing the workqueue
for kmpath_handlerd in multipath_postsuspend.
This patch waits for pg-init completion correctly in
multipath_postsuspend().
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
m->queue_io is set to block processing I/Os, and it needs to be kept
while pg-init, which issues multiple path activations, is in progress.
But m->queue is cleared when a path activation completes without error
in pg_init_done(), even while other path activations are in progress.
That may cause undesired -EIO on paths which are not complete activation.
This patch fixes that by not clearing m->queue_io until all path
activations complete.
(Before the hardware handlers were moved into the SCSI layer, pg_init
only used one path.)
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
'suspended' flag in struct multipath was introduced to check whether
the multipath target is in suspended state, but the same check is
done through dm_suspended() now, so remove the flag and related code.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove the dm_get() in dm_table_get_md() because dm_table_get_md() could
be called from presuspend/postsuspend, which are called while
mapped_device is in DMF_FREEING state, where dm_get() is not allowed.
Justification for that is the lifetime of both objects: As far as the
current dm design/implementation, mapped_device is never freed while
targets are doing something, because dm core waits for targets to become
quiet in dm_put() using presuspend/postsuspend. So targets should be
able to touch mapped_device without holding reference count of the
mapped_device, and we should allow targets to touch mapped_device even
if it is in DMF_FREEING state.
Backgrounds:
I'm trying to remove the multipath internal queue, since dm core now has
a generic queue for request-based dm. In the patch-set, the multipath
target wants to request dm core to start/stop queue. One of such
start/stop requests can happen during postsuspend() while the target
waits for pg-init to complete, because the target stops queue when
starting pg-init and tries to restart it when completing pg-init. Since
queue belongs to mapped_device, it involves calling dm_table_get_md()
and dm_put(). On the other hand, postsuspend() is called in dm_put()
for mapped_device which is in DMF_FREEING state, and that triggers
BUG_ON(DMF_FREEING) in the 2nd dm_put().
I had tried to solve this problem by changing only multipath not to
touch mapped_device which is in DMF_FREEING state, but I couldn't and I
came up with a question why we need dm_get() in dm_table_get_md().
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch adds two minor fixes while processing device mapper path activation.
Skip failed paths while calling activate_path. If the path is already failed
then activate_path will fail for sure. We don't have to call in that case. In
some case this might cause prolonged retries unnecessarily.
Change the misleading message if the path being activated fails with SCSI_DH_NOSYS.
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch removes some unnecessary argument casting. There is no
functional change with this patch.
Passes 'struct pgpath' through to pg_init_done() instead of the enclosed
'struct dm_path'.
Tested the changes with LSI storage..
CC: Chandra Seetharaman <chandra.seetharaman@us.ibm.com>
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Acked-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Except for SCSI no device drivers distinguish between physical and
hardware segment limits. Consolidate the two into a single segment
limit.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The block layer calling convention is blk_queue_<limit name>.
blk_queue_max_sectors predates this practice, leading to some confusion.
Rename the function to appropriately reflect that its intended use is to
set max_hw_sectors.
Also introduce a temporary wrapper for backwards compability. This can
be removed after the merge window is closed.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Add __percpu sparse annotations to places which didn't make it in one
of the previous patches. All converions are trivial.
These annotations are to make sparse consider percpu variables to be
in a different address space and warn if accessed without going
through percpu accessors. This patch doesn't affect normal builds.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Neil Brown <neilb@suse.de>
Revert commit d2bb7df8ca at Greg's request.
Author: Milan Broz <mbroz@redhat.com>
Date: Thu Dec 10 23:51:53 2009 +0000
dm: sysfs add empty release function to avoid debug warning
This patch just removes an unnecessary warning:
kobject: 'dm': does not have a release() function,
it is broken and must be fixed.
The kobject is embedded in mapped device struct, so
code does not need to release memory explicitly here.
Cc: Greg KH <gregkh@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch fixes the problem that system may stall if target's ->map_rq
returns DM_MAPIO_REQUEUE in map_request().
E.g. stall happens on 1 CPU box when a dm-mpath device with queue_if_no_path
bounces between all-paths-down and paths-up on I/O load.
When target's ->map_rq returns DM_MAPIO_REQUEUE, map_request() requeues
the request and returns to dm_request_fn(). Then, dm_request_fn()
doesn't exit the I/O dispatching loop and continues processing
the requeued request again.
This map and requeue loop can be done with interrupt disabled,
so 1 CPU system can be stalled if this situation happens.
For example, commands below can stall my 1 CPU box within 1 minute or so:
# dmsetup table mp
mp: 0 2097152 multipath 1 queue_if_no_path 0 1 1 service-time 0 1 2 8:144 1 1
# while true; do dd if=/dev/mapper/mp of=/dev/null bs=1M count=100; done &
# while true; do \
> dmsetup message mp 0 "fail_path 8:144" \
> dmsetup suspend --noflush mp \
> dmsetup resume mp \
> dmsetup message mp 0 "reinstate_path 8:144" \
> done
To fix the problem above, this patch changes dm_request_fn() to exit
the I/O dispatching loop once if a request is requeued in map_request().
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
When suspending a failed mirror, bios are completed by mirror_end_io() and
__rh_lookup() in dm_rh_dec() returns NULL where a non-NULL return value is
required by design. Fix this by not changing the state of the recovery failed
region from DM_RH_RECOVERING to DM_RH_NOSYNC in dm_rh_recovery_end().
Issue
On 2.6.33-rc1 kernel, I hit the bug when I suspended the failed
mirror by dmsetup command.
BUG: unable to handle kernel NULL pointer dereference at 00000020
IP: [<f94f38e2>] dm_rh_dec+0x35/0xa1 [dm_region_hash]
...
EIP: 0060:[<f94f38e2>] EFLAGS: 00010046 CPU: 0
EIP is at dm_rh_dec+0x35/0xa1 [dm_region_hash]
EAX: 00000286 EBX: 00000000 ECX: 00000286 EDX: 00000000
ESI: eff79eac EDI: eff79e80 EBP: f6915cd4 ESP: f6915cc4
DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
Process dmsetup (pid: 2849, ti=f6914000 task=eff03e80 task.ti=f6914000)
...
Call Trace:
[<f9530af6>] ? mirror_end_io+0x53/0x1b1 [dm_mirror]
[<f9413104>] ? clone_endio+0x4d/0xa2 [dm_mod]
[<f9530aa3>] ? mirror_end_io+0x0/0x1b1 [dm_mirror]
[<f94130b7>] ? clone_endio+0x0/0xa2 [dm_mod]
[<c02d6bcb>] ? bio_endio+0x28/0x2b
[<f952f303>] ? hold_bio+0x2d/0x62 [dm_mirror]
[<f952f942>] ? mirror_presuspend+0xeb/0xf7 [dm_mirror]
[<c02aa3e2>] ? vmap_page_range+0xb/0xd
[<f9414c8d>] ? suspend_targets+0x2d/0x3b [dm_mod]
[<f9414ca9>] ? dm_table_presuspend_targets+0xe/0x10 [dm_mod]
[<f941456f>] ? dm_suspend+0x4d/0x150 [dm_mod]
[<f941767d>] ? dev_suspend+0x55/0x18a [dm_mod]
[<c0343762>] ? _copy_from_user+0x42/0x56
[<f9417fb0>] ? dm_ctl_ioctl+0x22c/0x281 [dm_mod]
[<f9417628>] ? dev_suspend+0x0/0x18a [dm_mod]
[<f9417d84>] ? dm_ctl_ioctl+0x0/0x281 [dm_mod]
[<c02c3c4b>] ? vfs_ioctl+0x22/0x85
[<c02c422c>] ? do_vfs_ioctl+0x4cb/0x516
[<c02c42b7>] ? sys_ioctl+0x40/0x5a
[<c0202858>] ? sysenter_do_call+0x12/0x28
Analysis
When recovery process of a region failed, dm_rh_recovery_end() function
changes the state of the region from RM_RH_RECOVERING to DM_RH_NOSYNC.
When recovery_complete() is executed between dm_rh_update_states() and
dm_writes() in do_mirror(), bios are processed with the region state,
DM_RH_NOSYNC. However, the region data is freed without checking its
pending count when dm_rh_update_states() is called next time.
When bios are finished by mirror_end_io(), __rh_lookup() in dm_rh_dec()
returns NULL even though a valid return value are expected.
Solution
Remove the state change of the recovery failed region from DM_RH_RECOVERING
to DM_RH_NOSYNC in dm_rh_recovery_end(). We can remove the state change
because:
- If the region data has been released by dm_rh_update_states(),
a new region data is created with the state of DM_RH_NOSYNC, and
bios are processed according to the DM_RH_NOSYNC state.
- If the region data has not been released by dm_rh_update_states(),
a state of the region is DM_RH_RECOVERING and bios are put in the
delayed_bio list.
The flag change from DM_RH_RECOVERING to DM_RH_NOSYNC in dm_rh_recovery_end()
was added in the following commit:
dm raid1: handle resync failures
author Jonathan Brassow <jbrassow@redhat.com>
Thu, 12 Jul 2007 16:29:04 +0000 (17:29 +0100)
http://git.kernel.org/linus/f44db678edcc6f4c2779ac43f63f0b9dfa28b724
Signed-off-by: Takahiro Yasui <tyasui@redhat.com>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If the mirror log fails when the handle_errors option was not selected
and there is no remaining valid mirror leg, writes return success even
though they weren't actually written to any device. This patch
completes them with EIO instead.
This code path is taken:
do_writes:
bio_list_merge(&ms->failures, &sync);
do_failures:
if (!get_valid_mirror(ms)) (false)
else if (errors_handled(ms)) (false)
else bio_endio(bio, 0);
The logic in do_failures is based on presuming that the write was already
tried: if it succeeded at least on one leg (without handle_errors) it
is reported as success.
Reference: https://bugzilla.redhat.com/show_bug.cgi?id=555197
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch fixes two bugs that revolve around the miscalculation and
misuse of the variable 'overhead_size'. 'overhead_size' is the size of
the various header structures used during communication.
The first bug is the use of 'sizeof' with the pointer of a structure
instead of the structure itself - resulting in the wrong size being
computed. This is then used in a check to see if the payload
(data_size) would be to large for the preallocated structure. Since the
bug produces a smaller value for the overhead, it was possible for the
structure to be breached. (Although the current users of the code do
not currently send enough data to trigger this bug.)
The second bug is that the 'overhead_size' value is used to compute how
much of the preallocated space should be cleared before populating it
with fresh data. This should have simply been 'sizeof(struct cn_msg)'
not overhead_size. The fact that 'overhead_size' was computed
incorrectly made this problem "less bad" - leaving only a pointer's
worth of space at the end uncleared. Thus, this bug was never producing
a bad result, but still needs to be fixed - especially now that the
value is computed correctly.
Cc: stable@kernel.org
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
chunk_io() declares its 'struct mdata_req' on the stack and then
initializes its 'struct work_struct' member. Annotate the
initialization of this workqueue with INIT_WORK_ON_STACK to suppress a
debugobjects warning seen when CONFIG_DEBUG_OBJECTS_WORK is enabled.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If a table containing zero as stripe count is passed into stripe_ctr
the code attempts to divide by zero.
This patch changes DM_TABLE_LOAD to return -EINVAL if the stripe count
is zero.
We now get the following error messages:
device-mapper: table: 253:0: striped: Invalid stripe count
device-mapper: ioctl: error adding target to table
Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
======
This fix is related to
http://bugzilla.kernel.org/show_bug.cgi?id=15142
but does not address that exact issue.
======
sysfs does like attributes being removed while they are being accessed
(i.e. read or written) and waits for the access to complete.
As accessing some md attributes takes the same lock that is held while
removing those attributes a deadlock can occur.
This patch addresses 3 issues in md that could lead to this deadlock.
Two relate to calling flush_scheduled_work while the lock is held.
This is probably a bad idea in general and as we use schedule_work to
delete various sysfs objects it is particularly bad.
In one case flush_scheduled_work is called from md_alloc (called by
md_probe) called from do_md_run which holds the lock. This call is
only present to ensure that ->gendisk is set. However we can be sure
that gendisk is always set (though possibly we couldn't when that code
was originally written. This is because do_md_run is called in three
different contexts:
1/ from md_ioctl. This requires that md_open has succeeded, and it
fails if ->gendisk is not set.
2/ from writing a sysfs attribute. This can only happen if the
mddev has been registered in sysfs which happens in md_alloc
after ->gendisk has been set.
3/ from autorun_array which is only called by autorun_devices, which
checks for ->gendisk to be set before calling autorun_array.
So the call to md_probe in do_md_run can be removed, and the check on
->gendisk can also go.
In the other case flush_scheduled_work is being called in do_md_stop,
purportedly to wait for all md_delayed_delete calls (which delete the
component rdevs) to complete. However there really isn't any need to
wait for them - they have already been disconnected in all important
ways.
The third issue is that raid5->stop() removes some attribute names
while the lock is held. There is already some infrastructure in place
to delay attribute removal until after the lock is released (using
schedule_work). So extend that infrastructure to remove the
raid5_attrs_group.
This does not address all lockdep issues related to the sysfs
"s_active" lock. The rest can be address by splitting that lockdep
context between symlinks and non-symlinks which hopefully will happen.
Signed-off-by: NeilBrown <neilb@suse.de>
This code was written long ago when it was not possible to
reshape a degraded array. Now it is so the current level of
degraded-ness needs to be taken in to account. Also newly addded
devices should only reduce degradedness if they are deemed to be
in-sync.
In particular, if you convert a RAID5 to a RAID6, and increase the
number of devices at the same time, then the 5->6 conversion will
make the array degraded so the current code will produce a wrong
value for 'degraded' - "-1" to be precise.
If the reshape runs to completion end_reshape will calculate a correct
new value for 'degraded', but if a device fails during the reshape an
incorrect decision might be made based on the incorrect value of
"degraded".
This patch is suitable for 2.6.32-stable and if they are still open,
2.6.31-stable and 2.6.30-stable as well.
Cc: stable@kernel.org
Reported-by: Michael Evans <mjevans1983@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Make DM use bdev_stack_limits() function so that partition offsets get
taken into account when calculating alignment. Clarify stacking
warnings.
Also remove obsolete clearing of final alignment_offset and misalignment
flag.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: Alasdair G. Kergon <agk@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
If two arrays share a device, then they will not both resync at the
same time. One will wait for the other to complete.
While waiting, the MD_RECOVERY_INTR flag is not checked so a device
failure, which would make the resync pointless, does not cause the
resync to abort, so the failed device cannot be removed (as it cannot
be remove while a resync is happening).
So add a test for MD_RECOVERY_INTR.
Reported-by: Brett Russ <bruss@netezza.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Since commit dfc7064500,
->hot_remove_disks has not removed non-failed devices from
an array until recovery is no longer possible.
So the code in do_md_run to get around the fact that
md_check_recovery (which calls ->hot_remove_disks) would
remove partially-in-sync devices is no longer needed.
So remove it.
Signed-off-by: NeilBrown <neilb@suse.de>
By default md_do_sync() will perform recovery if no other actions are
specified. However, action_show() relies on MD_RECOVERY_RECOVER to be
set otherwise it returns 'idle'. So, add a missing set
MD_RECOVERY_RECOVER when starting recovery.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The start_ro modules parameter can be used to force arrays to be
started in 'auto-readonly' in which they are read-only until the first
write. This ensures that no resync/recovery happens until something
else writes to the device. This is important for resume-from-disk
off an md array.
However if an array is started 'readonly' (by writing 'readonly' to
the 'array_state' sysfs attribute) we want it to be really 'readonly',
not 'auto-readonly'.
So strengthen the condition to only set auto-readonly if the
array is not already read-only.
Signed-off-by: NeilBrown <neilb@suse.de>
evms configures md arrays by:
open device
send ioctl
close device
for each different ioctl needed.
Since 2.6.29, the device can disappear after the 'close'
unless a significant configuration has happened to the device.
The change made by "SET_ARRAY_INFO" can too minor to stop the device
from disappearing, but important enough that losing the change is bad.
So: make sure SET_ARRAY_INFO sets mddev->ctime, and keep the device
active as long as ctime is non-zero (it gets zeroed with lots of other
things when the array is stopped).
This is suitable for -stable kernels since 2.6.29.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm: (80 commits)
dm snapshot: use merge origin if snapshot invalid
dm snapshot: report merge failure in status
dm snapshot: merge consecutive chunks together
dm snapshot: trigger exceptions in remaining snapshots during merge
dm snapshot: delay merging a chunk until writes to it complete
dm snapshot: queue writes to chunks being merged
dm snapshot: add merging
dm snapshot: permit only one merge at once
dm snapshot: support barriers in snapshot merge target
dm snapshot: avoid allocating exceptions in merge
dm snapshot: rework writing to origin
dm snapshot: add merge target
dm exception store: add merge specific methods
dm snapshot: create function for chunk_is_tracked wait
dm snapshot: make bio optional in __origin_write
dm mpath: reject messages when device is suspended
dm: export suspended state to targets
dm: rename dm_suspended to dm_suspended_md
dm: swap target postsuspend call and setting suspended flag
dm crypt: add plain64 iv
...
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Makes use of skip_spaces() defined in lib/string.c for removing leading
spaces from strings all over the tree.
It decreases lib.a code size by 47 bytes and reuses the function tree-wide:
text data bss dec hex filename
64688 584 592 65864 10148 (TOTALS-BEFORE)
64641 584 592 65817 10119 (TOTALS-AFTER)
Also, while at it, if we see (*str && isspace(*str)), we can be sure to
remove the first condition (*str) as the second one (isspace(*str)) also
evaluates to 0 whenever *str == 0, making it redundant. In other words,
"a char equals zero is never a space".
Julia Lawall tried the semantic patch (http://coccinelle.lip6.fr) below,
and found occurrences of this pattern on 3 more files:
drivers/leds/led-class.c
drivers/leds/ledtrig-timer.c
drivers/video/output.c
@@
expression str;
@@
( // ignore skip_spaces cases
while (*str && isspace(*str)) { \(str++;\|++str;\) }
|
- *str &&
isspace(*str)
)
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com>
Cc: Julia Lawall <julia@diku.dk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Neil Brown <neilb@suse.de>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: David Howells <dhowells@redhat.com>
Cc: <linux-ext4@vger.kernel.org>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enable external metadata arrays to manage rebuild checkpointing via a
md/dev-XXX/recovery_start attribute which reflects rdev->recovery_offset
Also update resync_start_store to allow 'none' to be written, for
consistency.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Other walks of this list are either under rcu_read_lock() or the list
mutation lock (mddev_lock()). This protects against the improbable case of a
disk being removed from the array at the start of md_do_sync().
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
As v1.x metadata can record that a member of the array is
not completely recovered, it make sense to record that a
spare has become a regular member of the array at the earliest
opportunity.
So remove the tests on "recovery_offset > 0" in super_1_sync
as they really aren't needed, and schedule a metadata update
immediately after adding spares to a degraded array.
This means that if a crash happens immediately after a recovery
starts, the new device will be included in the array and recovery will
continue from wherever it was up to. Previously this didn't happen
unless recovery was at least 1/16 of the way through.
Signed-off-by: NeilBrown <neilb@suse.de>
The RAID ioctls are only implemented in md.c, so the
handling for them should also be moved there from
fs/compat_ioctl.c.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Neil Brown <neilb@suse.de>
Cc: Andre Noll <maan@systemlinux.org>
Cc: linux-raid@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Make it clear in the config message that MD_MULTIPATH is not under
active development.
Cc: Oren Held <orenhe@il.ibm.com>
Signed-off-by: NeilBrown <neilb@suse.de>
We've noticed severe lasting performance degradation of our raid
arrays when we have drives that yield large amounts of media errors.
The raid10 module will queue each failed read for retry, and also
will attempt call fix_read_error() to perform the read recovery.
Read recovery is performed while the array is frozen, so repeated
recovery attempts can degrade the performance of the array for
extended periods of time.
With this patch I propose adding a per md device max number of
corrected read attempts. Each rdev will maintain a count of
read correction attempts in the rdev->read_errors field (not
used currently for raid10). When we enter fix_read_error()
we'll check to see when the last read error occurred, and
divide the read error count by 2 for every hour since the
last read error. If at that point our read error count
exceeds the read error threshold, we'll fail the raid device.
In addition in this patch I add sysfs nodes (get/set) for
the per md max_read_errors attribute, the rdev->read_errors
attribute, and added some printk's to indicate when
fix_read_error fails to repair an rdev.
For testing I used debugfs->fail_make_request to inject
IO errors to the rdev while doing IO to the raid array.
Signed-off-by: Robert Becker <Rob.Becker@riverbed.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When we get a read error on a device in a RAID10, and attempting to
repair the error fails, print more useful messages about why it
failed.
Signed-off-by: Robert Becker <Rob.Becker@riverbed.com>
Signed-off-by: NeilBrown <neilb@suse.de>
There is a sysfs file which allows bits in the write-intent
bitmap to be explicit set - indicating that the block is thought
to be 'dirty'.
When this happens we should really set recovery_cp backwards
to include the block to reflect this dirtiness.
In particular, a 'resync' process will refuse to start if
recovery_cp is beyond the end of the array, so this is needed
to allow a resync to be triggered.
Signed-off-by: NeilBrown <neilb@suse.de>
In this case, the metadata needs to not be in the same
sector as the bitmap.
md will not read/write any bitmap metadata. Config must be
done via sysfs and when a recovery makes the array non-degraded
again, writing 'true' to 'bitmap/can_clear' will allow bits in
the bitmap to be cleared again.
Signed-off-by: NeilBrown <neilb@suse.de>
Setting daemon_lastrun really has nothing to do with reading
the bitmap superblock, it just happens to be needed at the same time.
bitmap_read_sb is about to become options, so move that code out
to after the call to bitmap_read_sb.
Signed-off-by: NeilBrown <neilb@suse.de>
A new attribute directory 'bitmap' in 'md' is created which
contains files for configuring the bitmap.
'location' identifies where the bitmap is, either 'none',
or 'file' or 'sector offset from metadata'.
Writing 'location' can create or remove a bitmap.
Adding a 'file' bitmap this way is not yet supported.
'chunksize' and 'time_base' must be set before 'location'
can be set.
'chunksize' can be set before creating a bitmap, but is
currently always over-ridden by the bitmap superblock.
'time_base' and 'backlog' can be updated at any time.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Andre Noll <maan@systemlinux.org>
safe_delay_store can parse fixed point numbers (for fractions
of a second). We will want to do that for another sysfs
file soon, so factor out the code.
Signed-off-by: NeilBrown <neilb@suse.de>
For md arrays were metadata is managed externally, the kernel does not
know about a superblock so the superblock offset is 0.
If we want to have a write-intent-bitmap near the end of the
devices of such an array, we should support sector_t sized offset.
We need offset be possibly negative for when the bitmap is before
the metadata, so use loff_t instead.
Also add sanity check that bitmap does not overlap with data.
Signed-off-by: NeilBrown <neilb@suse.de>
As bitmap_create and bitmap_destroy already set thread->timeout
as appropriate, there is no need to do it in raid10_quiesce.
There is a possible need to wake the thread after the timeout
has been set low, but it is better to do that where the timeout
is actually set low, in bitmap_create.
Signed-off-by: NeilBrown <neilb@suse.de>
... and into bitmap_info. These are all configuration parameters
that need to be set before the bitmap is created.
Signed-off-by: NeilBrown <neilb@suse.de>
In preparation for making bitmap fields configurable via sysfs,
start tidying up by making a single structure to contain the
configuration fields.
Signed-off-by: NeilBrown <neilb@suse.de>
This will allow us to stop writeout to portions of the array
while they are resynced by someone else - e.g. another node in
a cluster.
Signed-off-by: NeilBrown <neilb@suse.de>
The post-barrier-flush is sent by md as soon as make_request on the
barrier write completes. For raid5, the data might not be in the
per-device queues yet. So for barrier requests, wait for any
pre-reading to be done so that the request will be in the per-device
queues.
We use the 'preread_active' count to check that nothing is still in
the preread phase, and delay the decrement of this count until after
write requests have been submitted to the underlying devices.
Signed-off-by: NeilBrown <neilb@suse.de>
Previously barriers were only supported on RAID1. This is because
other levels requires synchronisation across all devices and so needed
a different approach.
Here is that approach.
When a barrier arrives, we send a zero-length barrier to every active
device. When that completes - and if the original request was not
empty - we submit the barrier request itself (with the barrier flag
cleared) and then submit a fresh load of zero length barriers.
The barrier request itself is asynchronous, but any subsequent
request will block until the barrier completes.
The reason for clearing the barrier flag is that a barrier request is
allowed to fail. If we pass a non-empty barrier through a striping
raid level it is conceivable that part of it could succeed and part
could fail. That would be way too hard to deal with.
So if the first run of zero length barriers succeed, we assume all is
sufficiently well that we send the request and ignore errors in the
second run of barriers.
RAID5 needs extra care as write requests may not have been submitted
to the underlying devices yet. So we flush the stripe cache before
proceeding with the barrier.
Note that the second set of zero-length barriers are submitted
immediately after the original request is submitted. Thus when
a personality finds mddev->barrier to be set during make_request,
it should not return from make_request until the corresponding
per-device request(s) have been queued.
That will be done in later patches.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Andre Noll <maan@systemlinux.org>
If a resync/recovery/check/repair is interrupted for some reason, it
can be useful to know exactly where it got up to.
So in that case, do not clear curr_resync_completed.
Initialise it when starting a resync/recovery/... instead.
Signed-off-by: NeilBrown <neilb@suse.de>
When a 'check' or 'repair' finished we should clear resync_min
so that a future check/repair will cover the whole array (by default).
However if it is interrupted, we should update resync_min to
where we got up to, so that when the check/repair continues it
just does the remainder of the array.
Signed-off-by: NeilBrown <neilb@suse.de>
A write intent bitmap can be removed from an array while the
array is active.
When this happens, all IO is suspended and flushed before the
bitmap is removed.
However it is possible that bitmap_daemon_work is still running to
clear old bits from the bitmap. If it is, it can dereference the
bitmap after it has been freed.
So introduce a new mutex to protect bitmap_daemon_work and get it
before destroying a bitmap.
This is suitable for any current -stable kernel.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
If the snapshot we are merging became invalid (e.g. it ran out of
space) redirect all I/O directly to the origin device.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Set 'merge_failed' flag if a snapshot fails to merge. Update
snapshot_status() to report "Merge failed" if 'merge_failed' is set.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
s->store->type->prepare_merge returns the number of chunks that can be
copied linearly working backwards from the returned chunk number.
For example, if it returns 3 chunks with old_chunk == 10 and new_chunk
== 20, then chunk 20 can be copied to 10, chunk 19 to 9 and 18 to 8.
Until now kcopyd only copied one chunk at a time. This patch now copies
the full set at once.
Consequently, snapshot_merge_process() needs to delay the merging of all
chunks if any have writes in progress, not just the first chunk in the
region that is to be merged.
snapshot-merge's performance is now comparable to the original
snapshot-origin target.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
When there is one merging snapshot and other non-merging snapshots,
snapshot_merge_process() must make exceptions in the non-merging
snapshots.
Use a sequence count to resolve the race between I/O to chunks that are
about to be merged. The count increases each time an exception
reallocation finishes. Use wait_event() to wait until the count
changes.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Track writes to chunks that are currently being merged and delay merging
a chunk until all writes to that chunk finish.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
While a set of chunks is being merged, any overlapping writes need to be
queued.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Merging is started when origin is resumed and it is stopped when
origin is suspended or when the merging snapshot is destroyed or
errors are detected.
Merging is not yet interlocked with writes: this will be handled in
subsequent patches.
The code relies on callbacks from a private kcopyd thread.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Merging more than one snapshot is not supported, so prevent
this happening.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Sets num_flush_requests=2 to support flushing both the origin and cow
devices used by the snapshot-merge target.
Also, snapshot_ctr() now gets the origin device using FMODE_WRITE if the
target is snapshot-merge (which writes to the origin device).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The snapshot-merge target should not allocate new exceptions because the
intent is to merge all of its exceptions as quickly and safely as
possible.
This patch introduces the snapshot-merge mapping function and updates
__origin_write() so that it doesn't allocate exceptions on any snapshots
that are being merged.
If a write request to a merging snapshot device is to be dispatched
directly to the origin (because the chunk is not remapped or was already
merged), snapshot_merge_map() must make exceptions in other snapshots so
calls do_origin().
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
To track the completion of exceptions relating to the same location on
the device, the current code selects one exception as primary_pe, links
the other exceptions to it and uses reference counting to wait until all
the reallocations are complete.
It is considered too complicated to extend this code to handle the new
snapshot-merge target, where sets of non-overlapping chunks would also
need to become linked.
Instead, a simpler (but less efficient) approach is taken. Bios are
linked to one exception. When it completes, bios are simply retried,
and if other related exceptions are still outstanding, they'll get
queued again to wait for another one.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The snapshot-merge target allows a snapshot to be merged back into the
snapshot's origin device.
One anticipated use of snapshot merging is the rollback of filesystems
to back out problematic system upgrades.
This patch adds snapshot-merge target management to both
dm_snapshot_init() and dm_snapshot_exit(). As an initial place-holder,
snapshot-merge is identical to the snapshot target. Documentation is
provided.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add functions that decide how many consecutive chunks of snapshot to
merge back into the origin next and to update the metadata afterwards.
prepare_merge provides a pointer to the most recent still-to-be-merged
chunk and returns how many previous ones are consecutive and can be
processed together.
commit_merge removes the nr_merged most-recent chunks permanently from
the exception store. The number must not exceed that returned by
prepare_merge.
Introduce NUM_SNAPSHOT_HDR_CHUNKS to show where the snapshot header
chunk is accounted for.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move the __chunk_is_tracked() loop into a separate function as we will
also need to call it from the write path in the rare case of conflicting
writes to the same chunk.
Originally introduced in commit a8d41b59f3
("dm snapshot: fix race during exception creation").
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
To support the merging of snapshots back into their origin we need
to trigger exceptions in other snapshots not being merged without
any incoming bio on the origin device. The bio parameter to
__origin_write() becomes optional and the sector needs supplying
separately.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch rejects messages that can generate I/O while the device
itself is suspended.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Cc: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch adds the exported dm_suspended() function so that targets
can check whether or not they are suspended.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch renames dm_suspended() to dm_suspended_md() and
keeps it internal to dm.
No functional change.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch moves DMF_SUSPENDED flag set before postsuspend.
No one should care about the ordering, because the flag set and
the postsuspend are protected by a single lock, md->suspend_lock,
and all strict flag-checkers take the lock.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The default plain IV is 32-bit only.
This plain64 IV provides a compatible mode for encrypted devices bigger
than 4TB.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Permit in-use snapshot exception data to be 'handed over' from one
snapshot instance to another. This is a pre-requisite for patches
that allow the changes made in a snapshot device to be merged back into
its origin device and also allows device resizing.
The basic call sequence is:
dmsetup load new_snapshot (referencing the existing in-use cow device)
- the ctr code detects that the cow is already in use and allows the
two snapshot target instances to be linked together
dmsetup suspend original_snapshot
dmsetup resume new_snapshot
- the new_snapshot becomes live, and if anything now tries to access
the original one it will receive -EIO
dmsetup remove original_snapshot
(There can only be two snapshot targets referencing the same cow device
simultaneously.)
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
When swapping a new table into place, retain the old table until
its replacement is in place.
An old check for an empty table is removed because this is enforced
in populate_table().
__unbind() becomes redundant when followed by __bind().
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
When replacing a mapped device's table during a 'resume', delay the
destruction of the old table until the new one is successfully in place.
This will make it easier for a later patch to transfer internal state
information from the old table to the new one (something we do not currently
support) while giving us more options for reversion if a later part
of the operation fails.
Devices are always in the suspended state during dm_swap_table().
This patch reinforces the requirement that all I/O must have been
flushed from the table targets while in this state (including any in
workqueues). In the case of 'noflush' suspending, unprocessed
I/O should have been 'pushed back' to the dm core prior to this point,
for resubmission after the new table is in place.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add the flag DM_QUERY_INACTIVE_TABLE_FLAG to the ioctls to return
infomation about the loaded-but-not-yet-active table instead of the live
table. Prior to this patch it was impossible to obtain this information
until the device had been 'resumed'.
Userspace dmsetup and libdevmapper support the flag as of version 1.02.40.
e.g. dmsetup info --inactive vg1-lv1
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Accept empty barriers in dm-io.
dm-io will process empty write barrier requests just like the other
read/write requests.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Reject messages that can generate I/O while the device itself
is suspended.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Acked-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add a mutex to allow possible creators of new work to synchronize with
flushing work queues.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Acked-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Once we begin deleting a device, prevent any further messages being sent
to targets of its table (to avoid races).
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add dm_deleting_md to check whether or not a given mapped
device is currently being deleted.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch stops the remaining dm-mpath activity during the suspend
sequence by flushing workqueues in postsuspend function.
The current dm-mpath target may not be quiet even after suspend completes
because some workqueues (e.g. device_handler's work, event handling)
are not flushed during the suspend sequence, even though suspended
devices/targets are supposed to be quiet in this state.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch adds barrier support for request-based dm.
CORE DESIGN
The design is basically same as bio-based dm, which emulates barrier
by mapping empty barrier bios before/after a barrier I/O.
But request-based dm has been using struct request_queue for I/O
queueing, so the block-layer's barrier mechanism can be used.
o Summary of the block-layer's behavior (which is depended by dm-core)
Request-based dm uses QUEUE_ORDERED_DRAIN_FLUSH ordered mode for
I/O barrier. It means that when an I/O requiring barrier is found
in the request_queue, the block-layer makes pre-flush request and
post-flush request just before and just after the I/O respectively.
After the ordered sequence starts, the block-layer waits for all
in-flight I/Os to complete, then gives drivers the pre-flush request,
the barrier I/O and the post-flush request one by one.
It means that the request_queue is stopped automatically by
the block-layer until drivers complete each sequence.
o dm-core
For the barrier I/O, treats it as a normal I/O, so no additional
code is needed.
For the pre/post-flush request, flushes caches by the followings:
1. Make the number of empty barrier requests required by target's
num_flush_requests, and map them (dm_rq_barrier()).
2. Waits for the mapped barriers to complete (dm_rq_barrier()).
If error has occurred, save the error value to md->barrier_error
(dm_end_request()).
(*) Basically, the first reported error is taken.
But -EOPNOTSUPP supersedes any error and DM_ENDIO_REQUEUE
follows.
3. Requeue the pre/post-flush request if the error value is
DM_ENDIO_REQUEUE. Otherwise, completes with the error value
(dm_rq_barrier_work()).
The pre/post-flush work above is done in the kernel thread (kdmflush)
context, since memory allocation which might sleep is needed in
dm_rq_barrier() but sleep is not allowed in dm_request_fn(), which is
an irq-disabled context.
Also, clones of the pre/post-flush request share an original, so
such clones can't be completed using the softirq context.
Instead, complete them in the context of underlying device drivers.
It should be safe since there is no I/O dispatching during
the completion of such clones.
For suspend, the workqueue of kdmflush needs to be flushed after
the request_queue has been stopped. Otherwise, the next flush work
can be kicked even after the suspend completes.
TARGET INTERFACE
No new interface is added.
Just use the existing num_flush_requests in struct target_type
as same as bio-based dm.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch moves dm_end_request() to make the next patch more readable.
No functional change.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch factors out the clone completion code, dm_done(),
from dm_softirq_done() in preparation for a subsequent patch.
No functional change.
dm_done() will be used in barrier completion, which can't use and
doesn't need softirq. The softirq_done callback needs to get a clone
from an original request but it can't in the case of barrier, where
an original request is shared by multiple clones. On the other hand,
the completion of barrier clones doesn't involve re-submitting requests,
which was the primary reason of the need for softirq.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch changes the counter for the number of in_flight I/Os
to md->pending from q->in_flight in preparation for a later patch.
No functional change.
Request-based dm used q->in_flight to count the number of in-flight
clones assuming the counter is always incremented for an in-flight
original request and original:clone is 1:1 relationship.
However, it this no longer true for barrier requests.
So use md->pending to count the number of in-flight clones.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The semantics of bio-based dm were changed recently in the case of
suspend with "--nolockfs" but without "--noflush".
Before 2.6.30, I/Os submitted before the suspend invocation were always
flushed. From 2.6.30 onwards, I/Os submitted before the suspend
invocation might not be flushed. (For details, see
http://marc.info/?t=123994433400003&r=1&w=2)
This patch brings the behaviour of request-based dm into line with
bio-based dm, simplifying the code and preparing for a subsequent patch
that will wait for all in_flight I/Os to complete without stopping
request_queue and use dm_wait_for_completion() for it.
This change in semantics simplifies the suspend code as follows:
o Suspend is implemented as stopping request_queue
in request-based dm, and all I/Os are queued in the request_queue
even after suspend is invoked.
o In the old semantics, we had to track whether I/Os were
queued before or after the suspend invocation, so a special
barrier-like request called 'suspend marker' was introduced.
o With the new semantics, we don't need to flush any I/O
so we can remove the marker and the code related to the marker
handling and I/O flushing.
After removing this codes, the suspend sequence is now:
1. Flush all I/Os by lock_fs() if needed.
2. Stop dispatching any I/O by stopping the request_queue.
3. Wait for all in-flight I/Os to be completed or requeued.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch factors out the request cloning code in dm_prep_fn()
as clone_rq(). No functional change.
This patch is a preparation for a later patch in this series which needs to
make clones from an original barrier request.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch adds the gfp_mask argument to alloc_rq_tio().
No functional change.
This patch is a preparation for a later patch in this series which needs to
allocate tio (for barrier I/O) with different allocation flag (GFP_NOIO) from
the one in the normal I/O code path.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch changes the argument of map_request() to clone request
from original request. No functional change.
This patch is a preparation for PATCH 9, which needs to use
map_request() for clones sharing an original barrier request.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch adds md_in_flight() to get the number of in_flight I/Os.
No functional change.
This patch is a preparation for a later patch in this series, which
changes I/O counter to md->pending from q->in_flight in request-based dm.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
dm-kcopyd: accept zero-size jobs
This patch changes dm-kcopyd so that it accepts zero-size jobs and completes
them immediatelly via its completion thread.
It is needed for multisnapshots snapshot resizing. When we are writing to
a chunk beyond origin end, no copying is done. To simplify the code, we submit
an empty request to kcopyd and let kcopyd complete it. If we didn't submit
a request to kcopyd and called the completion routine immediatelly, it would
violate the principle that completion is called only from one thread and
it would need additional locking.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Keep track of whether or not the device is suspended within the snapshot
target module, the same as we do in dm-raid1.
We will use this later to enforce the correct sequence of ioctls to
transfer the in-core exceptions from a snapshot target instance in
one table to a replacement one capable of merging them back
into the origin.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Store the reference to the snapshot cow device in the core snapshot
code instead of each exception store. It can be accessed through the
new function dm_snap_cow(). Exception stores should each now maintain a
reference to their parent snapshot struct.
This is cleaner and makes part of the forthcoming snapshot merge code simpler.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Add number of sectors used by metadata to the end of the snapshot's status
line.
Renamed dm_exception_store_type's 'fraction_full' to 'usage'. Renamed
arguments to be clearer about what is being returned. Also added
'metadata_sectors'.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Rename exception functions. Preparing to pull them out of
dm-snap.c for broader use.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Rename exception_table for broader use outside dm-snap.c
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The exception structure is not necessarily just a snapshot
element (especially after we pull it out of dm-snap.c).
Renaming appropriately.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Consolidate the insert_*exception functions. 'insert_completed_exception'
already contains all the logic to handle 'insert_exception' (via
check for a hash_shift of 0), so remove redundant function.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The origin needs to find minimum chunksize of all snapshots. This logic is
moved to a separate function because it will be used at another place in
the snapshot merge patches.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Removed unnecessary 'and' masking: The right shift discards the lower
bits so there is no need to clear them.
(A later patch needs this change to support a 32-bit chunk_mask.)
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Minor code touch-up. We don't need the 'else'.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Linus Torvalds