This pinconf_ops structure is only stored in the const pinconf_ops
field of a pinctrl_desc structure. Make the pinconf_ops structure
const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pin 23 on South bridge does not belong to the rgmii group. It belongs to
a separate group which can have 3 functions.
Due to this the fix also have to update the way the functions are
managed. Until now each groups used NB_FUNCS(which was 2) functions. For
the mpp23, 3 functions are available but it is the only group which needs
it, so on the loop involving NB_FUNCS an extra test was added to handle
only the functions added.
The bug was visible with the merge of the commit 07d065abf9 "arm64:
dts: marvell: armada-3720-db: Add vqmmc regulator for SD slot", the gpio
regulator used the gpio 23, due to this the whole rgmii group was setup
to gpio which broke the Ethernet support on the Armada 3720 DB
board. Thanks to this patch, the UHS SD cards (which need the vqmmc)
_and_ the Ethernet work again.
Cc: stable@vger.kernel.org
Fixes: 87466ccd94 ("pinctrl: armada-37xx: Add pin controller support
for Armada 37xx")
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The sdio_sb group is composed of 6 pins and not 5.
Reported-by: Ken Ma <make@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If north bridge selection register bit1 is clear, pins [10:8] are for
SDIO0 Resetn, Wakeup, and PDN while if bit1 is set, pins [10:8]are for
GPIO; when bit1 is clear, pin 9 and pin 10 can be used for uart2 RTSn
and CTSn, so bit1 should be added to uart2 group and it must be set
for both "gpio" and "uart" functions of uart2 group.
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit adds a pinctrl driver for the CP110 part of the Marvell
Armada 7K and 8K SoCs. The Armada 7K has a single CP110, where almost all
the MPP pins are available. On the other side, the Armada 8K has two
CP110, and the available MPPs are split between the master CP110 (MPPs 32
to 62) and the slave CP110 (MPPs 0 to 31).
The register interface to control the MPPs is however the same as all
other mvebu SoCs, so we can reuse the common pinctrl-mvebu.c logic.
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Reviewed-by: Shadi Ammouri <shadi@marvell.com>
[updated for mvebu pinctrl and 4.9 changes:
- converted to simple_mmio
- converted to syscon/regmap
- removed unimplemented .remove function
- dropped DTS changes
- defered gpio ranges to DT
- fixed warning
- properly set soc->nmodes
-- rmk]
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[ add missing MPP[61:56] function 14 (SDIO)
-- Konstantin Porotchkin]
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
[ allow to properly register more then one instance of this driver
-- Grzegorz Jaszczyk]
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[ - rebased on 4.12-rc1
- fixed the 80 character limit for mvebu_mpp_mode array
- aligned the compatible name on the ones already used
- fixed the MPP table for CP110: some MPP are not available on Armada 7K
-- Gregory CLEMENT]
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit adds a pinctrl driver for the pin-muxing controller found in
the AP806 part of the Marvell Armada 7K and 8K SoCs. Its register
interface is compatible with the one used by previous mvebu pin
controllers, so the common logic in drivers/pinctrl/mvebu/pinctrl-mvebu.c
is used.
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Reviewed-by: Shadi Ammouri <shadi@marvell.com>
[updated for mvebu pinctrl changes
- converted to simple_mmio
- removed unimplemented .remove function
- removed DTS description
- converted to use syscon/regmap
--rmk]
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Armada 8040 also needs orion pinctrl, and as these symbols are only
selected, there's no need to make them depend on PLAT_ORION.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The offset property of the pinctrl node, when a regmap is used in the
device tree, was never used nor documented in the binding. Moreover, the
compatible string is enough to let the driver know which offset using.
So this patch removes the property and move the information at the driver
level.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Armada 37xx SoCs can handle interrupt through GPIO. However it can
only manage the edge ones.
The way the interrupt are managed is classical so we can use the generic
interrupt chip model.
The only unusual "feature" is that many interrupts are connected to the
parent interrupt controller. But we do not take advantage of this and use
the chained irq with all of them.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO management is pretty simple and is part of the same IP than the pin
controller for the Armada 37xx SoCs. This patch adds the GPIO support to
the pinctrl-armada-37xx.c file, it also allows sharing common functions
between the gpiolib and the pinctrl drivers.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Armada 37xx SoC come with 2 pin controllers: one on the south
bridge (managing 28 pins) and one on the north bridge (managing 36 pins).
At the hardware level the controller configure the pins by group and not
pin by pin. This constraint is reflected in the design of the driver:
only the group related functions are implemented.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
None of the Kconfigs for any of these drivers are tristate, meaning
that they currently are not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the drivers there is no doubt they are builtin-only.
All drivers get the exact same change, so they are handled in batch.
Changes are (1) use builtin_platform_driver, (2) dont use module.h
(3) delete module_exit related code, (4) delete MODULE_DEVICE_TABLE,
and (5) delete MODULE_LICENCE/MODULE_AUTHOR and associated tags.
For the dove driver we explicitly disallow a driver unbind, since
that doesn't have a sensible use case anyway, and it allows us to
drop the ".remove" code for non-modular drivers.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
We deleted the MODULE_LICENSE etc. tags since all that information
is already contained at the top of the file in the comments.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This pinctrl driver supports the 98DX3236, 98DX3336 and 98DX4251 SoCs
from Marvell.
Signed-off-by: Kalyan Kinthada <kalyan.kinthada@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A cleanup caused a harmless warning:
drivers/pinctrl/mvebu/pinctrl-kirkwood.c: In function 'kirkwood_pinctrl_probe':
drivers/pinctrl/mvebu/pinctrl-kirkwood.c:460:19: error: unused variable 'res' [-Werror=unused-variable]
The obvious fix is to remove the declaration of the now unused
variable.
Fixes: ad9ec4ecee ("pinctrl: mvebu: switch drivers to generic simple mmio")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a simple regmap based pinctrl implementation for mvebu, for syscon
based regmap drivers.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the mvebu pinctrl drivers over to the generic simple mmio
implementation, saving a substantial number of lines of code in
the process.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Provide a generic simple mmio-based probe function and methods, which
pinctrl drivers can use to initialise the mvebu pinctrl subsystem.
Most mvebu pinctrl drivers can use this.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Provide per-control private data into each mvebu pinctrl method, which
will allow us to provide some completely generic helpers without the
global variable and per-instance function definitions that would be
required when we have multiple pin controllers on a SoC.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As the mvebu_mpp_ctrl structures contain function pointers, it is
preferable for these to be made read-only to prevent the function
pointers being modified. So make these const.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Single characters should be put into a sequence.
Thus use the corresponding function "seq_putc".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Strings which did not contain data format specifications should be put
into a sequence. Thus use the corresponding function "seq_puts".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The script "checkpatch.pl" pointed information out like the following.
WARNING: void function return statements are not generally useful
Thus remove such a statement in the affected function.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The script "checkpatch.pl" pointed information out like the following.
WARNING: Possible unnecessary 'out of memory' message
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kmalloc_array".
This issue was detected by using the Coccinelle software.
* Replace the specification of a data structure by a pointer dereference
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As far as I'm aware the mv88f5181-b1 and mv88f5181l are the same at the
pinctrl level, so re-use the definitions for both.
[gregory.clement@free-electrons.com: fix commit title]
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
On Marvell mv88f6180 with pin control driver one can not use multi
purpose pins 35 through 44.
I'm using this controller on an embedded board and i found that the
pin multiplexing is not the same as in the hardware spezification.
This patch alters the pin description so that mpp pins 0 to 19 as well
as 35 to 44 are usable.
Pin settings i used can be found here:
http://www.marvell.com/embedded-processors/kirkwood/assets/HW_88F6180_OpenSource.pdf
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Reviewed-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use devm_pinctrl_register() for pin control registration and remove
need of .remove callback.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Hongzhou Yang <hongzhou.yang@mediatek.com>
Cc: Fabian Frederick <fabf@skynet.be>
Cc: Andrew Andrianov <andrew@ncrmnt.org>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When assigning mpp settings from static mpp modes to mpp groups,
we do not want any groups that have no supported setting for a
specific Kirkwood variant. However, when there is at least a
single supported setting, we need to assign the number of all
settings in this mode to grp->num_settings as we are reusing
the static modes table.
Fixes: 0581b16b18 ("pinctrl: mvebu: complain about missing group after checking variant")
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Common MVEBU pinctrl driver core gets an array of controls to modify
a specific set of registers and an array of modes for each pingroup
from each of the different SoC families of MVEBU.
Some SoC families comprise different variants that differ in available
pingroups and also controls, but to ease driver development, we can
pass a variant mask to disable specific pingroups for some variants.
However, controls are limited to the true number of pinctrl groups
avaiable on a variant.
Now, when pinctrl core driver parses over above arrays, it tries to
match modes with available controls and complains about missing
controls for modes that are passed to the core but actually are not
avaiable on a variant with:
kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 36
This warning is a false-positive and annoying, so move the warning
after we checked the variant mask for each mode setting. Also, if
there is no supported setting for this variant, do not complain at
all.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reported-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
CONFIG_PINCTRL_MVEBU is more suitable than CONFIG_PLAT_ORION
to guard the drivers/pinctrl/mvebu/ directory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Core functionality:
- Enable exclusive pin ownership: it is possible to flag a pin
controller so that GPIO and other functions cannot use a single
pin simultaneously.
- New drivers:
- NXP LPC18xx System Control Unit pin controller
- Imagination Pistachio SoC pin controller
- New subdrivers:
- Freescale i.MX7d SoC
- Intel Sunrisepoint-H PCH
- Renesas PFC R8A7793
- Renesas PFC R8A7794
- Mediatek MT6397, MT8127
- SiRF Atlas 7
- Allwinner A33
- Qualcomm MSM8660
- Marvell Armada 395
- Rockchip RK3368
- Cleanups:
- A big cleanup of the Marvell MVEBU driver rectifying it to
correspond to reality
- Drop platform device probing from the SH PFC driver, we are now a
DT only shop for SuperH
- Drop obsolte multi-platform check for SH PFC
- Various janitorial: constification, grammar etc
- Improvements:
- The AT91 GPIO portions now supports the set_multiple() feature
- Split out SPI pins on the Xilinx Zynq
- Support DTs without specific function nodes in the i.MX driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=UyKm
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Here is the bulk of pin control changes for the v4.2 series: Quite a
lot of new SoC subdrivers and two new main drivers this time, apart
from that business as usual.
Details:
Core functionality:
- Enable exclusive pin ownership: it is possible to flag a pin
controller so that GPIO and other functions cannot use a single pin
simultaneously.
New drivers:
- NXP LPC18xx System Control Unit pin controller
- Imagination Pistachio SoC pin controller
New subdrivers:
- Freescale i.MX7d SoC
- Intel Sunrisepoint-H PCH
- Renesas PFC R8A7793
- Renesas PFC R8A7794
- Mediatek MT6397, MT8127
- SiRF Atlas 7
- Allwinner A33
- Qualcomm MSM8660
- Marvell Armada 395
- Rockchip RK3368
Cleanups:
- A big cleanup of the Marvell MVEBU driver rectifying it to
correspond to reality
- Drop platform device probing from the SH PFC driver, we are now a
DT only shop for SuperH
- Drop obsolte multi-platform check for SH PFC
- Various janitorial: constification, grammar etc
Improvements:
- The AT91 GPIO portions now supports the set_multiple() feature
- Split out SPI pins on the Xilinx Zynq
- Support DTs without specific function nodes in the i.MX driver"
* tag 'pinctrl-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (99 commits)
pinctrl: rockchip: add support for the rk3368
pinctrl: rockchip: generalize perpin driver-strength setting
pinctrl: sh-pfc: r8a7794: add SDHI pin groups
pinctrl: sh-pfc: r8a7794: add MMCIF pin groups
pinctrl: sh-pfc: add R8A7794 PFC support
pinctrl: make pinctrl_register() return proper error code
pinctrl: mvebu: armada-39x: add support for Armada 395 variant
pinctrl: mvebu: armada-39x: add missing SATA functions
pinctrl: mvebu: armada-39x: add missing PCIe functions
pinctrl: mvebu: armada-38x: add ptp functions
pinctrl: mvebu: armada-38x: add ua1 functions
pinctrl: mvebu: armada-38x: add nand functions
pinctrl: mvebu: armada-38x: add sata functions
pinctrl: mvebu: armada-xp: add dram functions
pinctrl: mvebu: armada-xp: add nand rb function
pinctrl: mvebu: armada-xp: add spi1 function
pinctrl: mvebu: armada-39x: normalize ref clock naming
pinctrl: mvebu: armada-xp: rename spi to spi0
pinctrl: mvebu: armada-370: align spi1 clock pin naming
pinctrl: mvebu: armada-370: align VDD cpu-pd pin naming with datasheet
...
Currently, pinctrl_register() just returns NULL on error, so the
callers can not know the exact reason of the failure.
Some of the pinctrl drivers return -EINVAL, some -ENODEV, and some
-ENOMEM on error of pinctrl_register(), although the error code
might be different from the real cause of the error.
This commit reworks pinctrl_register() to return the appropriate
error code and modifies all of the pinctrl drivers to use IS_ERR()
for the error checking and PTR_ERR() for getting the error code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Ray Jui <rjui@broadcom.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Acked-by: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Armada 39x SoC family has grown a new variant, the Armada 395,
which sits between the Armada 390 and Armada 398 in terms of
features. This commit adds support for this additional variant to the
Armada 39x pinctrl driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest version of the Armada 39x datasheet documents several new
SATA related functions on various MPP pins. This commit adds the
description of these new functions to the Armada 39x pinctrl driver as
well as to its DT binding documentation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest version of the Armada 39x datasheet documents several new
PCIe related functions on various MPP pins. This commit adds the
description of these new functions to the Armada 39x pinctrl driver as
well as to its DT binding documentation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest version of the Armada 38x datasheet documents several new
PTP related functions on various MPP pins. This commit adds the
description of these new functions to the Armada 38x pinctrl driver as
well as to its DT binding documentation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest version of the Armada 38x datasheet documents several new
UART1 related functions on various MPP pins. This commit adds the
description of these new functions to the Armada 38x pinctrl driver as
well as to its DT binding documentation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest version of the Armada 38x datasheet documents several new
NAND related functions on various MPP pins. This commit adds the
description of these new functions to the Armada 38x pinctrl driver as
well as to its DT binding documentation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest version of the Armada 38x datasheet documents several new
SATA related functions on various MPP pins. This commit adds the
description of these new functions to the Armada 38x pinctrl driver as
well as to its DT binding documentation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest Armada XP datasheet documents several new DRAM related
functions on various MPPs. This commit adds the description of these
new functions in the Armada XP pinctrl driver and its DT binding
documentation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest version of the Armada XP datasheet documents a new
NAND-related MPP function on MPP48, for which this commit adds
support.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest Armada XP datasheet documents that some of the MPP pins can
be used to access the second SPI bus, labelled 'spi1'. This commit
adds the corresponding pins in the pinctrl driver and its DT binding
documentation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit normalizes the subnames of the reference clock MPP pins in
the Armada 39x pinctrl driver to match with the name used on other
SoCs.
Since only the subnames are changed, DT backward compatibility is not
affected.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After updating to the latest Armada XP datasheet, we discovered that
there is a second SPI bus accessible from the MPP pins, called 'spi1'.
In order to be consistent with other SoCs having two SPI busses, this
commit renames the functions of the first SPI bus to 'spi0' instead of
just 'spi'.
This commit obviously breaks the DT backward compatibility for the
people using the "spi" function name in their Device Tree.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Across all SoCs, even on Armada 370 for SPI0, the clock pin uses the
'sck' subname and not 'clk', so this commit adjusts the code and
documentation accordingly.
Since this commit only changes the subname, DT backward compatibility
is not affected.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For consistency with the datasheet, this commit renames the VDD
function of the MPP4 pin.
While this changes the DT compatibility, it is not considered to be a
problem since this pin is unlikely to be used for anything but
debugging purposes.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit normalizes the naming of the Ethernet txclkout pin to be
the same accross Marvell SoCs. It is worth mentioning that the DT
binding documentation of the Armada XP was wrong for MPP12: it said
the function was ge1(txd0), while it is in fact ge1(txclkout). It is
however not really a fix worth sending to stable since it does not
change the behavior, and the driver itself was correct.
Since only the subnames are changed, DT backward compatibility is not
affected.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Julia Lawall