This patch just adds the HCI command structure for configuring the
current IAC LAP setting. The length of the command is variable and
supports more than two IAC. However since there is only general
discoverable and limited discoverable modes, this can be limited
to two possible IACs.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The return value of mgmt_write_scan_failed() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The return value of mgmt_connectable() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The return value of mgmt_discoverable() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add a new flag that can be set when in limited discoverable mode. This
flag will cause the limited discoverable bit in the class of device
value to bet set.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Magically updating the advertising data when some random command enables
advertising in the controller is not really a good idea. It also caused
a bit of complicated code with the exported hci_udpate_ad function that
is shared from many places.
This patch consolidates the advertising data update into the management
core. It also makes sure that when powering on with LE enabled or later
on enabling LE the controller has a good default for advertising data.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Read the current IAC LAP values when initializing the controller. The
values are not used, but it is good to have them in the trace files
for debugging purposes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When initializing a controller make sure to read out the number of
supported IAC and store its result. This value is needed to determine
if limited discoverable for BR/EDR can be configured or not.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Correct common misspelling of "identify" as "indentify" throughout
the kernel
Signed-off-by: Maxime Jayat <maxime@artisandeveloppeur.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Clearing the BT_SK_SUSPEND socket flag from the L2CAP core is causing
a dependency on the socket. So intead of doing that, use a channel
callback into the socket handling to resume.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The L2CAP core should not look into the socket flags to figure out the
setting of defer setup. So introduce a L2CAP channel flag that mirrors
the socket flag.
Since the defer setup option is only set in one place this becomes a
really easy thing to do.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The L2CAP connectionless channels use SOCK_DGRAM and recvmsg() and need
to receive the remote BD_ADDR and PSM information via msg_name from
the recvmsg() system call.
So in case the L2CAP socket is for connectionless channels, provide
a msg_name callback that can update the data. Also store the remote
BD_ADDR and PSM in the skb so it can be extracted later on.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This allows to add a per socket msg_name callback that can be used
for updating the msg_name information for recvmsg() system calls.
This feature is used by another patch to support address information
on L2CAP connectionless channels.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Every socket protocol now stores its own address information. So
just remove the generic src and dst fields since they are no longer
needed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The address information of RFCOMM sockets should be stored in its
own socket structure. Trying to generalize them is not helpful since
different transports have different address types.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The address information of SCO sockets should be stored in its own
socket structure. Trying to generalize them is not helpful since
different transports have different address types.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of storing a pointer to the addresses for the HCI device
and HCI connection, use them directly. With the recent changes
to address tracking of HCI connections, this becomes simple.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The L2CAP sockets can use BR/EDR public, LE public and LE random
addresses for various combinations of source and destination
devices. So make sure that getsockname(), getpeername() and
accept() return the correct address type.
For this the address type of the source and destination is stored
with the L2CAP channel information. The stored address type is
not the one specific for the HCI protocol. It is the address
type used for the L2CAP sockets and the management interface.
The underlying HCI connections store the HCI address type. If
needed, it gets converted to the socket address type.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With the effort of abstracting the L2CAP socket from the underlying
L2CAP channel it is important to store the source and destination
address information directly in the L2CAP channel structure.
Direct access to the HCI connection address information is not
possible since they might not be avaiable at L2CAP channel
creation time. The address information will be updated when
the underlying BR/EDR or LE connection status changes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The source addressed was based on the public address of the HCI device,
but with LE connections this not always the case. For example single
mode LE-only controllers would use a static random address. And this
address is configured by userspace.
To not complicate the lookup of what kind of address is in use, store
the correct source address for each HCI connection.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When establishing LE connections, it is possible to use a public
address (if available) or a random address. The type of address
is only known when creating connections, so make sure it is
stored in hci_conn structure.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bdaddr_to_le() function tries to convert the internal address
type to one that matches the HCI address type for LE. It does not
handle any address types not used by LE and in the end just make
the code a lot harder to read.
So instead of just hiding behind a magic function, just convert
the internal address type where it needs to be converted. And it
turns out that these are only two cases anyway. One when creating
new LE connections and the other when loading the long term keys.
In both cases this makes it more clear on what it going on.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The l2cap_conn->src and l2cap_conn->dst pointers are no longer in use
and so just remove them.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The implementation actually supports the L2CAP connectionless data
channel. So set it as supported in the fixed channels bitmask.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The PSM 0x0021 is dedicated to the 3D profile and has permission to
use security mode 4 level 0 for L2CAP connectionless unicast data
transfers.
When establishing a L2CAP connectionless channel on PSM 0x0021, it
will no longer force Secure Simple Pairing.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The scan interval and window parameters are used for LE passive
background scanning and connection establishment. This allows
userspace to change the values.
These two values should be kept in sync with whatever is used for
the scan parameters service on remote devices. And it puts the
controlling daemon (for example bluetoothd) in charge of setting
the values.
Main use case would be to switch between two sets of values. One
for foreground applications and one for background applications.
At this moment, the values are only used for manual connection
establishment, but soon that should be extended to background
scanning and automatic connection establishment.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The scan interval and window for LE passive scanning and connection
establishment should be configurable on a per controller basis. So
introduce a setting that later on will allow modifying it.
This setting does not affect LE active scanning during device
discovery phase. As long as that phase uses interleaved discovery,
it will continuously scan.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of masking hdev inside the skb->dev parameter, hand it
directly to the driver as a parameter to hdev->send. This makes
the driver interface more clear and simpler.
This patch fixes all drivers to accept and handle the new parameter
of hdev->send callback. Special care has been taken for bpa10x
and btusb drivers that require having skb->dev set to hdev for
the URB transmit complete handlers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To avoid casting skb->dev into hdev, just let the drivers provide
the hdev directly when calling hci_recv_frame() function.
This patch also fixes up all drivers to provide the hdev.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The smp.h header file is only used internally by the bluetooth.ko
module and is not a public API. So make it local to the core
Bluetooth module.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The a2mp.h header file is only used internally by the bluetooth.ko
module and is not a public API. So make it local to the core
Bluetooth module.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The amp.h header file is only used internally by the bluetooth.ko
module and is not a public API. So make it local to the core
Bluetooth module.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Since there is no use of hdev->ioctl by any Bluetooth driver since
ever, so just lets remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Conflicts:
drivers/net/wireless/brcm80211/brcmfmac/dhd_bus.h
drivers/net/wireless/rtlwifi/rtl8188ee/phy.h
drivers/net/wireless/rtlwifi/rtl8192ce/phy.h
drivers/net/wireless/rtlwifi/rtl8192de/phy.h
drivers/net/wireless/rtlwifi/rtl8723ae/phy.h
Just some minor conflicts between the wireless-next changes
and Joe Perches's "extern" removal from function prototypes
in header files.
John W. Linville says:
====================
Regarding the Bluetooth bits, Gustavo says:
"The big work here is from Marcel and Johan. They did a lot of work
in the L2CAP, HCI and MGMT layers. The most important ones are the
addition of a new MGMT command to enable/disable LE advertisement
and the introduction of the HCI user channel to allow applications
to get directly and exclusive access to Bluetooth devices."
As to the ath10k bits, Kalle says:
"Bartosz dropped support for qca98xx hw1.0 hardware from ath10k, it's
just too much to support it. Michal added support for the new firmware
interface. Marek fixed WEP in AP and IBSS mode. Rest of the changes are
minor fixes or cleanups."
And also:
"Major changes are:
* throughput improvements including aligning the RX frames correctly and
optimising HTT layer (Michal)
* remove qca98xx hw1.0 support (Bartosz)
* add support for firmware version 999.999.0.636 (Michal)
* firmware htt statistics support (Kalle)
* fix WEP in AP and IBSS mode (Marek)
* fix a mutex unlock balance in debugfs file (Shafi)
And of course there's a lot of smaller fixes and cleanup."
For the wl12xx bits, Luca says:
"Here are some patches intended for 3.13. Eliad is upstreaming a bunch
of patches that have been pending in the internal tree. Mostly bugfixes
and other small improvements."
Along with that...
Arend and friends bring us a batch of brcmfmac updates, Larry Finger
offers some rtlwifi refactoring, and Sujith sends the usual batch of
ath9k updates. As usual, there are a number of other small updates
from a variety of players as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When initializing an AMP controller, read its current known location
data so that it can be analyzed later on.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The return value of mgmt_discovering() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The return value of mgmt_remote_name() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The return value of mgmt_device_found() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The return value of mgmt_device_disconnected() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The return value of mgmt_device_connected() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The return value of mgmt_connect_failed() function is not used
so change it to just return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The return value of mgmt_disconnect_failed() function is not used
so change it to just return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The return value of mgmt_set_powered_failed() function is never used
and so make the function just return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The return value from mgmt_index_added() and mgmt_index_removed()
functions is never used. So do not pretend that returning an error
would actually be handled and just make both functions return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The helper function mgmt_valid_hdev() is more obfuscating the code
then it makes it easier to read. So intead of this helper, use the
direct check for BR/EDR device type.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The mgmt_new_settings() function was only needed to handle the
error case when re-enabling advertising failed. Since that is
now handled internally inside the management core, this function
is not needed anymore. So just remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the all LE connections have been disconneted, then it is up to
the host to re-enable advertising at that point. To ensure that the
correct advertising parameters are used, force the usage of the
common helper to enable advertising.
The change just moves the manual enabling of advertising from the
event handler into the management core so that the helper can
be actually shared.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add the basic HCI structure for building the LE advertising parameters
command.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hci_amp_capable() function has only a single user inside the L2CAP
core. Instead of exporting the function, place it next to its user.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The AMP controller status constants need to be actually used to avoid
crypted hardcoded numbers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The special AMP controller id 0 is reserved for the BR/EDR controller
that has the main link. It is a fixed value and so use a constant for
this throughout the code to make it more visible when the handling is
for the BR/EDR channel or when it is for the AMP channel.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There are two defined HCI device types. One is for BR/EDR controllers
and the other is for AMP controllers. The HCI device type is not the
same as the AMP controller type. It just happens that currently the
defined types match, but that is not guaranteed.
Split the usage of AMP controller type into its own domain so that
it is possible to separate between BR/EDR controllers, 802.11 AMP
controllers and any other AMP technology that might be defined in
the future.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add the constants for BR/EDR and 802.11 AMP controller types.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The list of controllers can be counted ahead of time and inline
inside the AMP discover handling. There is no need to export such
a function at all.
In addition just count the AMP controller and only allocated space
for a single mandatory BR/EDR controller. No need to allocate more
space than needed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
A function is needed so that the HCI event processing can ask the mgmt
code to emit a new settings event. This is necessary e.g. when the event
processing does updates to mgmt related states without any dependency of
actual mgmt commands.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This flag is used to indicate whether we want to have advertising
enabled or not, so give it a more suitable name.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Slave Page Response Timeout event indicates to the Host that a
slave page response timeout has occurred in the BR/EDR Controller.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 110
"7.7.72 Slave Page Response Timeout Event [New Section]
...
Note: this event will be generated if the slave BR/EDR Controller
responds to a page but does not receive the master FHS packet
(see Baseband, Section 8.3.3) within pagerespTO.
Event Parameters: NONE"
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Synchronization Train Complete event indicates that the Start
Synchronization Train command has completed.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 103
"7.7.67 Synchronization Train Complete Event [New Section]
...
Event Parameters:
Status 0x00 Start Synchronization Train command completed
successfully.
0x01-0xFF Start Synchronization Train command failed.
See Part D, Error Codes, for error codes and
descriptions."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Start_Synchronization_Train command controls the Synchronization
Train functionality in the BR/EDR Controller.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 86
"7.1.51 Start Synchronization Train Command [New Section]
...
If connectionless slave broadcast mode is not enabled, the Command
Disallowed (0x0C) error code shall be returned. After receiving this
command and returning a Command Status event, the Baseband starts
attempting to send synchronization train packets containing information
related to the enabled Connectionless Slave Broadcast packet timing.
Note: The AFH_Channel_Map used in the synchronization train packets is
configured by the Set_AFH_Channel_Classification command and the local
channel classification in the BR/EDR Controller.
The synchronization train packets will be sent using the parameters
specified by the latest Write_Synchronization_Train_Parameters command.
The Synchronization Train will continue until synchronization_trainTO
slots (as specified in the last Write_Synchronization_Train command)
have passed or until the Host disables the Connectionless Slave Broadcast
logical transport."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
he Set_Connectionless_Slave_Broadcast command controls the
Connectionless Slave Broadcast functionality in the BR/EDR
Controller.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 78
"7.1.49 Set Connectionless Slave Broadcast Command [New Section]
...
The LT_ADDR indicated in the Set_Connectionless_Slave_Broadcast shall be
pre-allocated using the HCI_Set_Reserved_LT_ADDR command. If the
LT_ADDR has not been reserved, the Unknown Connection Identifier (0x02)
error code shall be returned. If the controller is unable to reserve
sufficient bandwidth for the requested activity, the Connection Rejected
Due to Limited Resources (0x0D) error code shall be returned.
The LPO_Allowed parameter informs the BR/EDR Controller whether it is
allowed to sleep.
The Packet_Type parameter specifies which packet types are allowed. The
Host shall either enable BR packet types only, or shall enable EDR and DM1
packet types only.
The Interval_Min and Interval_Max parameters specify the range from which
the BR/EDR Controller must select the Connectionless Slave Broadcast
Interval. The selected Interval is returned."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Write_Synchronization_Train_Parameters command configures
the Synchronization Train functionality in the BR/EDR Controller.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 97
"7.3.90 Write Synchronization Train Parameters Command [New Section]
...
Note: The AFH_Channel_Map used in the Synchronization Train packets is
configured by the Set_AFH_Channel_Classification command and the local
channel classification in the BR/EDR Controller.
Interval_Min and Interval_Max specify the allowed range of
Sync_Train_Interval. Refer to [Vol. 2], Part B, section 2.7.2 for
a detailed description of Sync_Train_Interval. The BR/EDR Controller shall
select an interval from this range and return it in Sync_Train_Interval.
If the Controller is unable to select a value from this range, it shall
return the Invalid HCI Command Parameters (0x12) error code.
Once started (via the Start_Synchronization_Train Command) the
Synchronization Train will continue until synchronization_trainTO slots have
passed or Connectionless Slave Broadcast has been disabled."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Set_Connectionless_Slave_Broadcast_Data command provides the
ability for the Host to set Connectionless Slave Broadcast data in
the BR/EDR Controller.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 93
"7.3.88 Set Connectionless Slave Broadcast Data Command [New Section]
...
If connectionless slave broadcast mode is disabled, this data shall be
kept by the BR/EDR Controller and used once connectionless slave broadcast
mode is enabled. If connectionless slave broadcast mode is enabled,
and this command is successful, this data will be sent starting with
the next Connectionless Slave Broadcast instant.
The Data_Length field may be zero, in which case no data needs to be
provided.
The Host may fragment the data using the Fragment field in the command. If
the combined length of the fragments exceeds the capacity of the largest
allowed packet size specified in the Set Connectionless Slave Broadcast
command, all fragments associated with the data being assembled shall be
discarded and the Invalid HCI Command Parameters error (0x12) shall be
returned."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Delete_Reserved_LT_ADDR command requests that the BR/EDR
Controller cancel the reservation for a specific LT_ADDR reserved for the
purposes of Connectionless Slave Broadcast.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 92
"7.3.87 Delete Reserved LT_ADDR Command [New Section]
...
If the LT_ADDR indicated in the LT_ADDR parameter is not reserved by the
BR/EDR Controller, it shall return the Unknown Connection Identifier (0x02)
error code.
If connectionless slave broadcast mode is still active, then the Controller
shall return the Command Disallowed (0x0C) error code."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Set_Reserved_LT_ADDR command allows the host to request that the
BR/EDR Controller reserve a specific LT_ADDR for Connectionless Slave
Broadcast.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 90
"7.3.86 Set Reserved LT_ADDR Command [New Section]
...
If the LT_ADDR indicated in the LT_ADDR parameter is already in use by the
BR/EDR Controller, it shall return the ACL Connection Already Exists (0x0B)
error code. If the LT_ADDR indicated in the LT_ADDR parameter is out of
range, the controller shall return the Invalid HCI Command Parameters (0x12)
error code. If the command succeeds, then the reserved LT_ADDR shall be
used when issuing subsequent Set Connectionless Slave Broadcast Data and
Set Connectionless Slave Broadcast commands.
To ensure that the reserved LT_ADDR is not already allocated, it is
recommended that this command be issued at some point after HCI_Reset is
issued but before page scanning is enabled or paging is initiated."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
On dual-mode BR/EDR/LE and LE only controllers it is possible
to configure a random address. There are two types or random
addresses, one is static and the other private. Since the
random private addresses require special privacy feature to
be supported, the configuration of these two are kept separate.
This command allows for setting the static random address. It is
only supported on controllers with LE support. The static random
address is suppose to be valid for the lifetime of the controller
or at least until the next power cycle. To ensure such behavior,
setting of the address is limited to when the controller is
powered off.
The special BDADDR_ANY address (00:00:00:00:00:00) can be used to
disable the static address. This is also the default value.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch introduces a new mgmt command for enabling/disabling BR/EDR
functionality. This can be convenient when one wants to make a dual-mode
controller behave like a single-mode one. The command is only available
for dual-mode controllers and requires that LE is enabled before using
it. The BR/EDR setting can be enabled at any point, however disabling it
requires the controller to be powered off (otherwise a "rejected"
response will be sent).
Disabling the BR/EDR setting will automatically disable all other BR/EDR
related settings.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To allow treating dual-mode (BR/EDR/LE) controllers as single-mode ones
(LE-only) we want to introduce a new HCI_BREDR_ENABLED flag to track
whether BR/EDR is enabled or not (previously we simply looked at the
feature bit with lmp_bredr_enabled).
This patch add the new flag and updates the relevant places to test
against it instead of using lmp_bredr_enabled. The flag is by default
enabled when registering an adapter and only cleared if necessary once
the local features have been read during the HCI init procedure.
We cannot completely block BR/EDR usage in case user space uses raw HCI
sockets but the patch tries to block this in places where possible, such
as the various BR/EDR specific ioctls.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Hiding the Bluetooth high speed support behind a module parameter is
not really useful. This can be enabled and disabled at runtime via
the management interface. This also has the advantage that this can
now be changed per controller and not just global.
This patch removes the module parameter and exposes the high speed
setting of the management interface to all controllers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The BDADDR_LOCAL is a relict from userspace and has never been used
within the kernel. So remove that constant and replace it with a new
BDADDR_NONE that is similar to HCI_DEV_NONE with all bits set.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Conflicts:
drivers/net/ethernet/emulex/benet/be.h
drivers/net/usb/qmi_wwan.c
drivers/net/wireless/brcm80211/brcmfmac/dhd_bus.h
include/net/netfilter/nf_conntrack_synproxy.h
include/net/secure_seq.h
The conflicts are of two varieties:
1) Conflicts with Joe Perches's 'extern' removal from header file
function declarations. Usually it's an argument signature change
or a function being added/removed. The resolutions are trivial.
2) Some overlapping changes in qmi_wwan.c and be.h, one commit adds
a new value, another changes an existing value. That sort of
thing.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new mgmt command for enabling and disabling
LE advertising. The command depends on the LE setting being enabled
first and will return a "rejected" response otherwise. The patch also
adds safeguards so that there will ever only be one set_le or
set_advertising command pending per adapter.
The response handling and new_settings event sending is done in an
asynchronous request callback, meaning raw HCI access from user space to
enable advertising (e.g. hciconfig leadv) will not trigger the
new_settings event. This is intentional since trying to support mixed
raw HCI and mgmt access would mean adding extra state tracking or new
helper functions, essentially negating the benefit of using the
asynchronous request framework. The HCI_LE_ENABLED and HCI_LE_PERIPHERAL
flags however are updated correctly even with raw HCI access so this
will not completely break subsequent access over mgmt.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds a new mgmt setting for LE advertising and hooks up the
necessary places in the mgmt code to operate on the HCI_LE_PERIPHERAL
flag (which corresponds to this setting). This patch does not yet add
any new command for enabling the setting - that is left for a subsequent
patch.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch updates the code to use an asynchronous request for handling
the enabling and disabling of LE support. This refactoring is necessary
as a preparation for adding advertising support, since when LE is
disabled we should also disable advertising, and the cleanest way to do
this is to perform the two respective HCI commands in the same
asynchronous request.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For those controller that support the HCI_Set_Event_Mask_Page_2 command
we should include it in the init sequence. This patch implements sending
of the command and enables the events in it based on supported features
(currently only CSB is checked).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds support for reading the synchronization train parameters
for controllers that support the feature. Since the feature is
detectable through the local features page 2, which is retreived only in
stage 3 of the HCI init sequence, there is no other option than to add a
fourth stage to the init sequence.
For now the patch doesn't yet add storing of the parameters, but it is
nevertheless convenient to have around to see what kind of parameters
various controllers use by default (analyzable e.g. with the btmon user
space tool).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
In the case of blocking sockets we should not proceed with sendmsg() if
the socket has the BT_SK_SUSPEND flag set. So far the code was only
ensuring that POLLOUT doesn't get set for non-blocking sockets using
poll() but there was no code in place to ensure that blocking sockets do
the right thing when writing to them.
This patch adds a new bt_sock_wait_ready helper function to sleep in the
sendmsg call if the BT_SK_SUSPEND flag is set, and wake up as soon as it
is unset. It also updates the L2CAP and RFCOMM sendmsg callbacks to take
advantage of this new helper function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The struct for HCI_Set_Event_Mask is never used. Instead a local 8-byte
array is used for sending this command. Therefore, remove the
unnecessary struct definition.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This makes it more convenient to check for rfkill (no need to check for
dev->rfkill before calling rfkill_blocked()) and also avoids potential
races if the RFKILL state needs to be checked from within the rfkill
callback.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch introcuces a new HCI socket channel that allows user
applications to take control over a specific HCI device. The application
gains exclusive access to this device and forces the kernel to stay away
and not manage it. In case of the management interface it will actually
hide the device.
Such operation is useful for security testing tools that need to operate
underneath the Bluetooth stack and need full control over a device. The
advantage here is that the kernel still provides the service of hardware
abstraction and HCI level access. The use of Bluetooth drivers for
hardware access also means that sniffing tools like btmon or hcidump
are still working and the whole set of transaction can be traced with
existing tools.
With the new channel it is possible to send HCI commands, ACL and SCO
data packets and receive HCI events, ACL and SCO packets from the
device. The format follows the well established H:4 protocol.
The new HCI user channel can only be established when a device has been
through its setup routine and is currently powered down. This is
enforced to not cause any problems with current operations. In addition
only one user channel per HCI device is allowed. It is exclusive access
for one user application. Access to this channel is limited to process
with CAP_NET_RAW capability.
Using this new facility does not require any external library or special
ioctl or socket filters. Just create the socket and bind it. After that
the file descriptor is ready to speak H:4 protocol.
struct sockaddr_hci addr;
int fd;
fd = socket(AF_BLUETOOTH, SOCK_RAW, BTPROTO_HCI);
memset(&addr, 0, sizeof(addr));
addr.hci_family = AF_BLUETOOTH;
addr.hci_dev = 0;
addr.hci_channel = HCI_CHANNEL_USER;
bind(fd, (struct sockaddr *) &addr, sizeof(addr));
The example shows on how to create a user channel for hci0 device. Error
handling has been left out of the example. However with the limitations
mentioned above it is advised to handle errors. Binding of the user
cahnnel socket can fail for various reasons. Specifically if the device
is currently activated by BlueZ or if the access permissions are not
present.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch introduces a new user channel flag that allows to give full
control of a HCI device to a user application. The kernel will stay away
from the device and does not allow any further modifications of the
device states.
The existing raw flag is not used since it has a bit of unclear meaning
due to its legacy. Using a new flag makes the code clearer.
A device with the user channel flag set can still be enumerate using the
legacy API, but it does not longer enumerate using the new management
interface used by BlueZ 5 and beyond. This is intentional to not confuse
users of modern systems.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When initiating a transparent eSCO connection, make use of T2 settings
at first try. T2 is the recommended settings from HFP 1.6 WideBand
Speech. Upon connection failure, try T1 settings.
When CVSD is requested and eSCO is supported, try to establish eSCO
connection using S3 settings. If it fails, fallback in sequence to S2,
S1, D1, D0 settings.
To know which setting should be used, conn->attempt is used. It
indicates the currently ongoing SCO connection attempt and can be used
as the index for the fallback settings table.
These setting and the fallback order are described in Bluetooth HFP 1.6
specification p. 101.
Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch defines constants and macro for transparent data LMP
features. It refers to Bluetooth Core V4.0 specification, Part C, Chap
3.3 which defines LMP feature mask.
Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
In order to establish a transparent SCO connection, the correct settings
must be specified in the Setup Synchronous Connection request. For that,
a setting field is added to ACL connection data to set up the desired
parameters. The patch also removes usage of hdev->voice_setting in CVSD
connection and makes use of T2 parameters for transparent data.
Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch defines constants for SCO airmode from SCO voice setting. It
refers to Bluetooth Core V4.0 specification, Part E, Chap 6.12 which
describe SCO voice setting format.
Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch extends the current Bluetooth socket options with BT_VOICE.
This is intended to choose voice data type at runtime. It only applies
to SCO sockets. Incoming connections shall be setup during deferred
setup. Outgoing connections shall be setup before connect(). The desired
setting is stored in the SCO socket info. This patch declares needed
members, modifies getsockopt() and setsockopt().
Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
hci_connect is a super function for connecting hci protocols. But the
voice_setting parameter (introduced in subsequent patches) is only
needed by SCO and security requirements are not needed for SCO channels.
Thus, it makes sense to have a separate function for SCO.
Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Add macros for the HCI capabilities as described in the Bluetooth Core
Specification v4.0, Volume 2, part E, section 7.1.29.
Signed-off-by: Mikel Astiz <mikel.astiz@bmw-carit.de>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Remove HCI_LINK_KEYS flag since using HCI_MGMT is enough for test that
user space expects the kernel managing link keys.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch removes hci_do_inquiry and hci_cancel_inquiry helpers. We
now use the HCI request framework in device discovery functionality
and these helpers are no longer needed.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch removes the LE scan helpers hci_le_scan and hci_cancel_
le_scan and all code related to it. We now use the HCI request
framework in device discovery functionality and these helpers are
no longer needed.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
mgmt_stop_discovery_failed is now only used in mgmt.c so we can
make it a local function. This patch also moves the mgmt_stop_
discovery_failed definition up in mgmt.c to avoid forward
declaration.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
In order to have a better HCI error handling in interleaved discovery
functionality, we should use the HCI request framework.
This patch updates le_scan_disable_work function so it uses the
HCI request framework instead of the hci_send_cmd helper. A complete
callback is registered (le_scan_disable_work_complete function) so we
are able to trigger the inquiry procedure (if we are running the
interleaved discovery) or to stop the discovery procedure (if we are
running LE-only discovery).
This patch also removes the extra logic in hci_cc_le_set_scan_enable
to trigger the inquiry procedure and the mgmt_interleaved_discovery
function since they become useless.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Some of discovery macros will be used in hci_core so we need to
define them in common place such as hci_core.h. Thus, this patch
moves discovery macros to hci_core.h and also adds the DISCOV_
prefix to them.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
mgmt_start_discovery_failed is now only used in mgmt.c so we can
make it a local function. This patch also moves the mgmt_start_
discovery_failed definition up in mgmt.c to avoid forward
declaration.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
In order to use HCI request framework in start_discovery, we'll need
to call inquiry_cache_flush in mgmt.c. Therefore, this patch adds the
hci_ prefix to inquiry_cache_flush and makes it non-static.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
In future Core Specification versions the ATT CID will be just one of
many possible CIDs that can be used for data transfer. Therefore, it
makes sense to rename the define for the ATT CID to something less
ambigous.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
If hci_dev_open fails we need to ensure that the corresponding
mgmt_set_powered command gets an appropriate response. This patch fixes
the missing response by adding a new mgmt_set_powered_failed function
that's used to indicate a power on failure to mgmt. Since a situation
with the device being rfkilled may require special handling in user
space the patch uses a new dedicated mgmt status code for this.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Marcel Holtmann