Each time a flow finishes reads from the classification shadow
configuration in the driver, that flow would check for pending commands
and pass them to FW if possible.
In case there's already a completion pending command, I.e., a ramrod
that has been sent to the FW and is yet to be completed while said flow
tries to configure the pending command we would get a false error message
in logs [and panic if SOE was used for driver compilation] since the
command could not have been completed.
This prevents said print [and panic]; The pending command will be sent by
the time the completion of the current sent command would arrive.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool shows KR supported/advertised speeds incorrectly as baseT
in cases the board is in fact KR-base.
Signed-off-by: Yaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes several issues relating to asymmetric configuration:
1. When user requests to disable TX, the local-device needs to
advertise both PAUSE and ASM_DIR, but to avoid transmitting pause
frames. In the 578xx, it would ignore the TX disable.
2. When user advertises RX-only, ASM_DIR was advertised instead of
PAUSE/ASM_DIR.
3. When changing mode, the advertised PAUSE/ASM_DIR was not cleared
before setting new one, so disabling RX or TX had no impact on the
'advertised' as appeared in the 'ethtool -a' output.
Signed-off-by: Yaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use spinlock to access a single flag. We can avoid spin_locks by using
atomic variable and atomic_cmpxchg(). Use atomic_cmpxchg to set the flag
for idle to poll. And a simple atomic_set to unlock (set idle from poll).
In napi poll, if gro is enabled, we call napi_gro_receive() to deliver the
packets. Before we call napi_complete(), i.e while re-polling, if low
latency busy poll is called, we use netif_receive_skb() to deliver the packets.
At this point if there are some skb's held in GRO, busy poll could deliver the
packets out of order. So we call napi_gro_flush() to flush skbs before we
move the napi poll to idle.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vitesse VSC8641 is compatible with Vitesse 82xx
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_GIANFAR is not depended on FSL_SOC, it
can be built on non-PPC platforms.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was a missing assignment so the "if (ret)" on the next line is
never true.
Fixes: f21fb3ed36 ('Add support of Cavium Liquidio ethernet adapters')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to unlock before returning here.
Fixes: a0d2f20650 ('Renesas Ethernet AVB PTP clock driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When in HA mode, the driver exposes an IB (RoCE) device instance with only
one port. Under SRIOV, the existing implementation doesn't go well with
the PF RoCE driver's role of Special QPs Para-Virtualization, etc.
As such, disable HA for the mlx4 PF RoCE device in SRIOV mode.
Fixes: a575009030 ('IB/mlx4: Add port aggregation support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check_csum() function relied on hwtstamp_rx_filter to know if rxvlan
offload is disabled. This is wrong since rxvlan offload can be switched
on/off regardless of hwtstamp_rx_filter.
Also moved check_csum to query CQE information to identify VLAN packets
and removed the check of IP packets, since it has been validated before.
Fixes: f8c6455bb0 ('net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE')
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indication of a single completed packet, marked by txbbs_skipped
being bigger then zero, in not enough in order to wake up a
stopped TX queue. The completed packet may contain a single TXBB,
while next packet to be sent (after the wake up) may have multiple
TXBBs (LSO/TSO packets for example), causing overflow in queue followed
by WQE corruption and TX queue timeout.
Instead, wake the stopped queue only when there's enough room for the
worst case (maximum sized WQE) packet that we should need to handle after
the queue is opened again.
Also created an helper routine - mlx4_en_is_tx_ring_full, which checks
if the current TX ring is full or not. It provides better code readability
and removes code duplication.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX ring QP wasn't released at mlx4_en_destroy_tx_ring. Instead, the code
used the deprecated base_tx_qpn field. Move TX QP release to
mlx4_en_destroy_tx_ring and remove the base_tx_qpn field.
Fixes: ddae0349fd ('net/mlx4: Change QP allocation scheme')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Add TX fast path in mac80211, from Johannes Berg.
2) Add TSO/GRO support to ibmveth, from Thomas Falcon
3) Move away from cached routes in ipv6, just like ipv4, from Martin
KaFai Lau.
4) Lots of new rhashtable tests, from Thomas Graf.
5) Run ingress qdisc lockless, from Alexei Starovoitov.
6) Allow servers to fetch TCP packet headers for SYN packets of new
connections, for fingerprinting. From Eric Dumazet.
7) Add mode parameter to pktgen, for testing receive. From Alexei
Starovoitov.
8) Cache access optimizations via simplifications of build_skb(), from
Alexander Duyck.
9) Move page frag allocator under mm/, also from Alexander.
10) Add xmit_more support to hv_netvsc, from KY Srinivasan.
11) Add a counter guard in case we try to perform endless reclassify
loops in the packet scheduler.
12) Extern flow dissector to be programmable and use it in new "Flower"
classifier. From Jiri Pirko.
13) AF_PACKET fanout rollover fixes, performance improvements, and new
statistics. From Willem de Bruijn.
14) Add netdev driver for GENEVE tunnels, from John W Linville.
15) Add ingress netfilter hooks and filtering, from Pablo Neira Ayuso.
16) Fix handling of epoll edge triggers in TCP, from Eric Dumazet.
17) Add an ECN retry fallback for the initial TCP handshake, from Daniel
Borkmann.
18) Add tail call support to BPF, from Alexei Starovoitov.
19) Add several pktgen helper scripts, from Jesper Dangaard Brouer.
20) Add zerocopy support to AF_UNIX, from Hannes Frederic Sowa.
21) Favor even port numbers for allocation to connect() requests, and
odd port numbers for bind(0), in an effort to help avoid
ip_local_port_range exhaustion. From Eric Dumazet.
22) Add Cavium ThunderX driver, from Sunil Goutham.
23) Allow bpf programs to access skb_iif and dev->ifindex SKB metadata,
from Alexei Starovoitov.
24) Add support for T6 chips in cxgb4vf driver, from Hariprasad Shenai.
25) Double TCP Small Queues default to 256K to accomodate situations
like the XEN driver and wireless aggregation. From Wei Liu.
26) Add more entropy inputs to flow dissector, from Tom Herbert.
27) Add CDG congestion control algorithm to TCP, from Kenneth Klette
Jonassen.
28) Convert ipset over to RCU locking, from Jozsef Kadlecsik.
29) Track and act upon link status of ipv4 route nexthops, from Andy
Gospodarek.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1670 commits)
bridge: vlan: flush the dynamically learned entries on port vlan delete
bridge: multicast: add a comment to br_port_state_selection about blocking state
net: inet_diag: export IPV6_V6ONLY sockopt
stmmac: troubleshoot unexpected bits in des0 & des1
net: ipv4 sysctl option to ignore routes when nexthop link is down
net: track link-status of ipv4 nexthops
net: switchdev: ignore unsupported bridge flags
net: Cavium: Fix MAC address setting in shutdown state
drivers: net: xgene: fix for ACPI support without ACPI
ip: report the original address of ICMP messages
net/mlx5e: Prefetch skb data on RX
net/mlx5e: Pop cq outside mlx5e_get_cqe
net/mlx5e: Remove mlx5e_cq.sqrq back-pointer
net/mlx5e: Remove extra spaces
net/mlx5e: Avoid TX CQE generation if more xmit packets expected
net/mlx5e: Avoid redundant dev_kfree_skb() upon NOP completion
net/mlx5e: Remove re-assignment of wq type in mlx5e_enable_rq()
net/mlx5e: Use skb_shinfo(skb)->gso_segs rather than counting them
net/mlx5e: Static mapping of netdev priv resources to/from netdev TX queues
net/mlx4_en: Use HW counters for rx/tx bytes/packets in PF device
...
Conflicts:
drivers/net/ethernet/mellanox/mlx4/main.c
net/packet/af_packet.c
Both conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation of descriptor init procedure only takes
care about setting/clearing ownership flag in "des0"/"des1"
fields while it is perfectly possible to get unexpected bits
set because of the following factors:
[1] On driver probe underlying memory allocated with
dma_alloc_coherent() might not be zeroed and so
it will be filled with garbage.
[2] During driver operation some bits could be set by SD/MMC
controller (for example error flags etc).
And unexpected and/or randomly set flags in "des0"/"des1"
fields may lead to unpredictable behavior of GMAC DMA block.
This change addresses both items above with:
[1] Use of dma_zalloc_coherent() instead of simple
dma_alloc_coherent() to make sure allocated memory is
zeroed. That shouldn't affect performance because
this allocation only happens once on driver probe.
[2] Do explicit zeroing of both "des0" and "des1" fields
of all buffer descriptors during initialization of
DMA transfer.
And while at it fixed identation of dma_free_coherent()
counterpart as well.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: arc-linux-dev@synopsys.com
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org
Cc: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This bug pops up with NetworkManager on Fedora 21. NetworkManager tends to
stop the interface (nicvf_stop() is called) before changing settings. In
stopped state MAC cannot be sent to a PF. However, when the interface is
restarted (nicvf_open() is called), we ping the PF using NIC_MBOX_MSG_READY
message, and the PF replies back with old MAC address, overriding what we
had after MAC setting from userspace. As a result, we cannot set MAC
address using NetworkManager.
This patch introduces special tracking of MAC change in stopped state so
that the correct new MAC address is sent to a PF when interface is reopen.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefetch the 1st cache line used by the buffer pointed by
the skb linear data.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate between mlx5e_get_cqe() and mlx5_cqwq_pop(), this helps for
better code readability and better CQ buffer management.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use container_of() instead.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Coding Style fix, remove extra spaces.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to save PCI BW consumed by TX CQEs and to reduce the amount of
CPU cache misses caused by TX CQE reading, we request TX CQE generation
only when skb->xmit_more=0.
As a consequence of the above, a single TX CQE may now indicate the
transmission completion of multiple TX SKBs.
This also handles a problem introduced in commit b1b8105ebf41 "net/mlx5e:
Support NETIF_F_SG" where we didn't ask for NOP completions while the
driver didn't have the proper code to handle this case.
Fixes: b1b8105ebf41 ('net/mlx5e: Support NETIF_F_SG')
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NOP completion SKBs are always NULL.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is already assigned at mlx5e_build_rq_param()
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of counting number of gso fragments, we can use
skb_shinfo(skb)->gso_segs.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To save per-packet calculations, we use the following static mappings:
1) priv {channel, tc} to netdev txq (used @mlx5e_selec_queue())
2) netdev txq to priv sq (used @mlx5e_xmit())
Thanks to these static mappings, no more need for a separate implementation
of ndo_start_xmit when multiple TCs are configured.
We believe the performance improvement of such separation would be negligible, if any.
The previous way of dynamically calculating the above mappings required
allocating more TX queues than actually used (@alloc_etherdev_mqs()),
which is now no longer needed.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under SRIOV, the port rx/tx bytes/packets statistics should by read
from the HW instead of using the PF netdevice SW accounting. This is
needed in order to get the full port statistics and not just the PF
own ones
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NUM_ALL_STATS was not updated with the new four entries, instead
NUM_FLOW_STATS was updated, fix it. that caused off-by-four for all
counters below pf_*_*.
Fixes: b42de4d012 ('net/mlx4_en: Show PF own statistics via ethtool')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- A large cleanup of how device capabilities are checked for various
features
- Additional cleanups in the MAD processing
- Update to the srp driver
- Creation and use of centralized log message helpers
- Add const to a number of args to calls and clean up call chain
- Add support for extended cq create verb
- Add support for timestamps on cq completion
- Add support for processing OPA MAD packets
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yISf
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
- a large cleanup of how device capabilities are checked for various
features
- additional cleanups in the MAD processing
- update to the srp driver
- creation and use of centralized log message helpers
- add const to a number of args to calls and clean up call chain
- add support for extended cq create verb
- add support for timestamps on cq completion
- add support for processing OPA MAD packets
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (92 commits)
IB/mad: Add final OPA MAD processing
IB/mad: Add partial Intel OPA MAD support
IB/mad: Add partial Intel OPA MAD support
IB/core: Add OPA MAD core capability flag
IB/mad: Add support for additional MAD info to/from drivers
IB/mad: Convert allocations from kmem_cache to kzalloc
IB/core: Add ability for drivers to report an alternate MAD size.
IB/mad: Support alternate Base Versions when creating MADs
IB/mad: Create a generic helper for DR forwarding checks
IB/mad: Create a generic helper for DR SMP Recv processing
IB/mad: Create a generic helper for DR SMP Send processing
IB/mad: Split IB SMI handling from MAD Recv handler
IB/mad cleanup: Generalize processing of MAD data
IB/mad cleanup: Clean up function params -- find_mad_agent
IB/mlx4: Add support for CQ time-stamping
IB/mlx4: Add mmap call to map the hardware clock
IB/core: Pass hardware specific data in query_device
IB/core: Add timestamp_mask and hca_core_clock to query_device
IB/core: Extend ib_uverbs_create_cq
IB/core: Add CQ creation time-stamping flag
...
- ACPICA update to upstream revision 20150515 including basic
support for ACPI 6 features: new ACPI tables introduced by
ACPI 6 (STAO, XENV, WPBT, NFIT, IORT), changes related to the
other tables (DTRM, FADT, LPIT, MADT), new predefined names
(_BTH, _CR3, _DSD, _LPI, _MTL, _PRR, _RDI, _RST, _TFP, _TSN),
fixes and cleanups (Bob Moore, Lv Zheng).
- ACPI device power management core code update to follow ACPI 6
which reflects the ACPI device power management implementation
in Windows (Rafael J Wysocki).
- Rework of the backlight interface selection logic to reduce the
number of kernel command line options and improve the handling
of DMI quirks that may be involved in that and to make the
code generally more straightforward (Hans de Goede).
- Fixes for the ACPI Embedded Controller (EC) driver related to
the handling of EC transactions (Lv Zheng).
- Fix for a regression related to the ACPI resources management
and resulting from a recent change of ACPI initialization code
ordering (Rafael J Wysocki).
- Fix for a system initialization regression related to ACPI
introduced during the 3.14 cycle and caused by running the
code that switches the platform over to the ACPI mode too
early in the initialization sequence (Rafael J Wysocki).
- Support for the ACPI _CCA device configuration object related
to DMA cache coherence (Suravee Suthikulpanit).
- ACPI/APEI fixes and cleanups (Jiri Kosina, Borislav Petkov).
- ACPI battery driver cleanups (Luis Henriques, Mathias Krause).
- ACPI processor driver cleanups (Hanjun Guo).
- Cleanups and documentation update related to the ACPI device
properties interface based on _DSD (Rafael J Wysocki).
- ACPI device power management fixes (Rafael J Wysocki).
- Assorted cleanups related to ACPI (Dominik Brodowski. Fabian
Frederick, Lorenzo Pieralisi, Mathias Krause, Rafael J Wysocki).
- Fix for a long-standing issue causing General Protection Faults
to be generated occasionally on return to user space after resume
from ACPI-based suspend-to-RAM on 32-bit x86 (Ingo Molnar).
- Fix to make the suspend core code return -EBUSY consistently in
all cases when system suspend is aborted due to wakeup detection
(Ruchi Kandoi).
- Support for automated device wakeup IRQ handling allowing drivers
to make their PM support more starightforward (Tony Lindgren).
- New tracepoints for suspend-to-idle tracing and rework of the
prepare/complete callbacks tracing in the PM core (Todd E Brandt,
Rafael J Wysocki).
- Wakeup sources framework enhancements (Jin Qian).
- New macro for noirq system PM callbacks (Grygorii Strashko).
- Assorted cleanups related to system suspend (Rafael J Wysocki).
- cpuidle core cleanups to make the code more efficient (Rafael J
Wysocki).
- powernv/pseries cpuidle driver update (Shilpasri G Bhat).
- cpufreq core fixes related to CPU online/offline that should
reduce the overhead of these operations quite a bit, unless the
CPU in question is physically going away (Viresh Kumar, Saravana
Kannan).
- Serialization of cpufreq governor callbacks to avoid race
conditions in some cases (Viresh Kumar).
- intel_pstate driver fixes and cleanups (Doug Smythies, Prarit
Bhargava, Joe Konno).
- cpufreq driver (arm_big_little, cpufreq-dt, qoriq) updates (Sudeep
Holla, Felipe Balbi, Tang Yuantian).
- Assorted cleanups in cpufreq drivers and core (Shailendra Verma,
Fabian Frederick, Wang Long).
- New Device Tree bindings for representing Operating Performance
Points (Viresh Kumar).
- Updates for the common clock operations support code in the PM
core (Rajendra Nayak, Geert Uytterhoeven).
- PM domains core code update (Geert Uytterhoeven).
- Intel Knights Landing support for the RAPL (Running Average Power
Limit) power capping driver (Dasaratharaman Chandramouli).
- Fixes related to the floor frequency setting on Atom SoCs in the
RAPL power capping driver (Ajay Thomas).
- Runtime PM framework documentation update (Ben Dooks).
- cpupower tool fix (Herton R Krzesinski).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=7jTj
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"The rework of backlight interface selection API from Hans de Goede
stands out from the number of commits and the number of affected
places perspective. The cpufreq core fixes from Viresh Kumar are
quite significant too as far as the number of commits goes and because
they should reduce CPU online/offline overhead quite a bit in the
majority of cases.
From the new featues point of view, the ACPICA update (to upstream
revision 20150515) adding support for new ACPI 6 material to ACPICA is
the one that matters the most as some new significant features will be
based on it going forward. Also included is an update of the ACPI
device power management core to follow ACPI 6 (which in turn reflects
the Windows' device PM implementation), a PM core extension to support
wakeup interrupts in a more generic way and support for the ACPI _CCA
device configuration object.
The rest is mostly fixes and cleanups all over and some documentation
updates, including new DT bindings for Operating Performance Points.
There is one fix for a regression introduced in the 4.1 cycle, but it
adds quite a number of lines of code, it wasn't really ready before
Thursday and you were on vacation, so I refrained from pushing it on
the last minute for 4.1.
Specifics:
- ACPICA update to upstream revision 20150515 including basic support
for ACPI 6 features: new ACPI tables introduced by ACPI 6 (STAO,
XENV, WPBT, NFIT, IORT), changes related to the other tables (DTRM,
FADT, LPIT, MADT), new predefined names (_BTH, _CR3, _DSD, _LPI,
_MTL, _PRR, _RDI, _RST, _TFP, _TSN), fixes and cleanups (Bob Moore,
Lv Zheng).
- ACPI device power management core code update to follow ACPI 6
which reflects the ACPI device power management implementation in
Windows (Rafael J Wysocki).
- rework of the backlight interface selection logic to reduce the
number of kernel command line options and improve the handling of
DMI quirks that may be involved in that and to make the code
generally more straightforward (Hans de Goede).
- fixes for the ACPI Embedded Controller (EC) driver related to the
handling of EC transactions (Lv Zheng).
- fix for a regression related to the ACPI resources management and
resulting from a recent change of ACPI initialization code ordering
(Rafael J Wysocki).
- fix for a system initialization regression related to ACPI
introduced during the 3.14 cycle and caused by running the code
that switches the platform over to the ACPI mode too early in the
initialization sequence (Rafael J Wysocki).
- support for the ACPI _CCA device configuration object related to
DMA cache coherence (Suravee Suthikulpanit).
- ACPI/APEI fixes and cleanups (Jiri Kosina, Borislav Petkov).
- ACPI battery driver cleanups (Luis Henriques, Mathias Krause).
- ACPI processor driver cleanups (Hanjun Guo).
- cleanups and documentation update related to the ACPI device
properties interface based on _DSD (Rafael J Wysocki).
- ACPI device power management fixes (Rafael J Wysocki).
- assorted cleanups related to ACPI (Dominik Brodowski, Fabian
Frederick, Lorenzo Pieralisi, Mathias Krause, Rafael J Wysocki).
- fix for a long-standing issue causing General Protection Faults to
be generated occasionally on return to user space after resume from
ACPI-based suspend-to-RAM on 32-bit x86 (Ingo Molnar).
- fix to make the suspend core code return -EBUSY consistently in all
cases when system suspend is aborted due to wakeup detection (Ruchi
Kandoi).
- support for automated device wakeup IRQ handling allowing drivers
to make their PM support more starightforward (Tony Lindgren).
- new tracepoints for suspend-to-idle tracing and rework of the
prepare/complete callbacks tracing in the PM core (Todd E Brandt,
Rafael J Wysocki).
- wakeup sources framework enhancements (Jin Qian).
- new macro for noirq system PM callbacks (Grygorii Strashko).
- assorted cleanups related to system suspend (Rafael J Wysocki).
- cpuidle core cleanups to make the code more efficient (Rafael J
Wysocki).
- powernv/pseries cpuidle driver update (Shilpasri G Bhat).
- cpufreq core fixes related to CPU online/offline that should reduce
the overhead of these operations quite a bit, unless the CPU in
question is physically going away (Viresh Kumar, Saravana Kannan).
- serialization of cpufreq governor callbacks to avoid race
conditions in some cases (Viresh Kumar).
- intel_pstate driver fixes and cleanups (Doug Smythies, Prarit
Bhargava, Joe Konno).
- cpufreq driver (arm_big_little, cpufreq-dt, qoriq) updates (Sudeep
Holla, Felipe Balbi, Tang Yuantian).
- assorted cleanups in cpufreq drivers and core (Shailendra Verma,
Fabian Frederick, Wang Long).
- new Device Tree bindings for representing Operating Performance
Points (Viresh Kumar).
- updates for the common clock operations support code in the PM core
(Rajendra Nayak, Geert Uytterhoeven).
- PM domains core code update (Geert Uytterhoeven).
- Intel Knights Landing support for the RAPL (Running Average Power
Limit) power capping driver (Dasaratharaman Chandramouli).
- fixes related to the floor frequency setting on Atom SoCs in the
RAPL power capping driver (Ajay Thomas).
- runtime PM framework documentation update (Ben Dooks).
- cpupower tool fix (Herton R Krzesinski)"
* tag 'pm+acpi-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (194 commits)
cpuidle: powernv/pseries: Auto-promotion of snooze to deeper idle state
x86: Load __USER_DS into DS/ES after resume
PM / OPP: Add binding for 'opp-suspend'
PM / OPP: Allow multiple OPP tables to be passed via DT
PM / OPP: Add new bindings to address shortcomings of existing bindings
ACPI: Constify ACPI device IDs in documentation
ACPI / enumeration: Document the rules regarding the PRP0001 device ID
ACPI / video: Make acpi_video_unregister_backlight() private
acpi-video-detect: Remove old API
toshiba-acpi: Port to new backlight interface selection API
thinkpad-acpi: Port to new backlight interface selection API
sony-laptop: Port to new backlight interface selection API
samsung-laptop: Port to new backlight interface selection API
msi-wmi: Port to new backlight interface selection API
msi-laptop: Port to new backlight interface selection API
intel-oaktrail: Port to new backlight interface selection API
ideapad-laptop: Port to new backlight interface selection API
fujitsu-laptop: Port to new backlight interface selection API
eeepc-laptop: Port to new backlight interface selection API
dell-wmi: Port to new backlight interface selection API
...
kernel series:
- A big set of cleanups to the aged sysfs interface from
Johan Hovold. To get these in, v4.1-rc3 was merged into
the tree as the first patch in that series had to go
into stable. This makes the locking much more fine-grained
(get rid of the "big GPIO lock(s)" and store states in the
GPIO descriptors.
- Rename gpiod_[g|s]et_array() to gpiod_[g|s]et_array_value()
to avoid confusions.
- New drivers for:
- NXP LPC18xx (currently LPC1850)
- NetLogic XLP
- Broadcom STB SoC's
- Axis ETRAXFS
- Zynq Ultrascale+ (subdriver)
- ACPI:
- Make it possible to retrieve GpioInt resources from
a GPIO device using acpi_dev_gpio_irq_get()
- Merge some dependent I2C changes exploiting this.
- Support the ARM X-Gene GPIO standby driver.
- Make it possible for the generic GPIO driver to read
back the value set registers to reflect current
status.
- Loads of OMAP IRQ handling fixes.
- Incremental improvements to Kona, max732x, OMAP, MXC, RCAR,
PCA953x, STP-XWAY, PCF857x, Crystalcove, TB10x.
- Janitorial (contification, checkpatch cleanups)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVh76DAAoJEEEQszewGV1zYFsP/AnyCHs4M67k5Eegxtiwoomc
OTqkVtOcob9kfqMkbZ1dsjZe2ZYIDiyWeQ1xuV+dD9nx/iAu6inUxb0dXhxKXonr
+7mQglg32+zWTepLOJosoftoIqOb06lsMfgjL+tJcY5Od7/rewpdEplfEcjmq1O0
0OdaV2FCXIhHDt52iYHT4tYI1GCky9K4Au9NlPCbKAsGneb3fQahF9o3JpYXl1Oq
YhIFzUEhM+Zi2IoRsloGdK/eGEHni59IDekhZDf4PnYgA4Dkx2/e1A2Q0h5oT+QI
j2yfRbI9t1gA5UK7JR/rVJF+5+E8uZ06TZgTo8tU00U4ZvppNgHt8O4KZkJMFBce
KZzD9rkVVGp0NIDVwmOWjnfwkVVcQzMg/Wf17oM+qdaPO4GHEXNaQaInk1zmwqZq
tQiTk47zA4rrEaYq3YZjt4xQjl8+ExDlOzFjnfLYAm27gbIl6EFWbX2ON981MC8g
Nap8MLZINbGTlyDHtuqUlnqN+oXoP8niFuuDixYR+pM1P1bgwIVF+VopRJBFJRJP
IeR6VdsI9KS99Kg8ICf4ds6WdKAGU3Htj+26udgMhIlOWrkCbvvexIxq9oBkwIB1
VZofnSZLqnlKvo9Z140atvJWkFti7mqhItVjohmZyvyImLtmQBMq3kSGurXEqWms
/NGZ0txPd1lMHx5o6ZPK
=vKYs
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio updates from Linus Walleij:
"This is the big bulk of GPIO changes queued for the v4.2 kernel
series:
- a big set of cleanups to the aged sysfs interface from Johan
Hovold. To get these in, v4.1-rc3 was merged into the tree as the
first patch in that series had to go into stable. This makes the
locking much more fine-grained (get rid of the "big GPIO lock(s)"
and store states in the GPIO descriptors.
- rename gpiod_[g|s]et_array() to gpiod_[g|s]et_array_value() to
avoid confusions.
- New drivers for:
* NXP LPC18xx (currently LPC1850)
* NetLogic XLP
* Broadcom STB SoC's
* Axis ETRAXFS
* Zynq Ultrascale+ (subdriver)
- ACPI:
* make it possible to retrieve GpioInt resources from a GPIO
device using acpi_dev_gpio_irq_get()
* merge some dependent I2C changes exploiting this.
* support the ARM X-Gene GPIO standby driver.
- make it possible for the generic GPIO driver to read back the value
set registers to reflect current status.
- loads of OMAP IRQ handling fixes.
- incremental improvements to Kona, max732x, OMAP, MXC, RCAR,
PCA953x, STP-XWAY, PCF857x, Crystalcove, TB10x.
- janitorial (constification, checkpatch cleanups)"
* tag 'gpio-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (71 commits)
gpio: Fix checkpatch.pl issues
gpio: pcf857x: handle only enabled irqs
gpio / ACPI: Return -EPROBE_DEFER if the gpiochip was not found
GPIO / ACPI: export acpi_gpiochip_request(free)_interrupts for module use
gpio: improve error reporting on own descriptors
gpio: promote own request failure to pr_err()
gpio: Added support to Zynq Ultrascale+ MPSoC
gpio: add ETRAXFS GPIO driver
fix documentation after renaming gpiod_set_array to gpiod_set_array_value
gpio: Add GPIO support for Broadcom STB SoCs
gpio: xgene: add ACPI support for APM X-Gene GPIO standby driver
gpio: tb10x: Drop unneeded free_irq() call
gpio: crystalcove: set IRQCHIP_SKIP_SET_WAKE for the irqchip
gpio: stp-xway: Use the of_property_read_u32 helper
gpio: pcf857x: Check for irq_set_irq_wake() failures
gpio-stp-xway: Fix enabling the highest bit of the PHY LEDs
gpio: Prevent an integer overflow in the pca953x driver
gpio: omap: rework omap_gpio_irq_startup to handle current pin state properly
gpio: omap: rework omap_gpio_request to touch only gpio specific registers
gpio: omap: rework omap_x_irq_shutdown to touch only irqs specific registers
...
This patches fixes the code to check for IS_ERR rather
than NULL for clock interface.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the ACPI support for SGMII0 and XFI1 interface of
2nd H/W version of APM X-Gene SoC ethernet controller.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the backward compatibility with the old firmware where
the Tx completion IRQ interrupt was absent whereas incase of new firmware
the Tx completion IRQ interrupt is present.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements couple of fixes to support ACPI for RGMII/SGMII0/XFI
interface of APM X-Gene SoC ethernet controller driver. This patch uses
the _SUN acpi object to fetch the port-id information whereas the FDT uses
port-id binding for port-id information.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple LAN device for debug or management purposes.
Device supports interrupts for RX and TX(completion).
Device does not have DMA ability.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Tal Zilcer <talz@ezchip.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the correct unregister function matching the register
function on the error path.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Fixes: c1beeef7a3 ("rocker: implement IPv4 fib offloading")
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Below case causes mii bus probe failed:
ifconfig eth0 down -> suspend/resume with Mega/fax mix off -> ifconfig eth0 up
In i.MX6SX/i.MX7D chip, Mega/fast mix off feature is supported that means most of
SOC power will be off including ENET MAC for power saving. Once ENET MAC power
off, all initialized MAC registers reset to default, so in the case, it must
init MAC prior to mii bus probe.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One more missing piece of the puzzle. Add vlan dump support to switchdev
port's bridge_getlink. iproute2 "bridge vlan show" cmd already knows how
to show the vlans installed on the bridge and the device , but (until now)
no one implemented the port vlan part of the netlink PF_BRIDGE:RTM_GETLINK
msg. Before this patch, "bridge vlan show":
$ bridge -c vlan show
port vlan ids
sw1p1 30-34 << bridge side vlans
57
sw1p1 << device side vlans (missing)
sw1p2 57
sw1p2
sw1p3
sw1p4
br0 None
(When the port is bridged, the output repeats the vlan list for the vlans
on the bridge side of the port and the vlans on the device side of the
port. The listing above show no vlans for the device side even though they
are installed).
After this patch:
$ bridge -c vlan show
port vlan ids
sw1p1 30-34 << bridge side vlan
57
sw1p1 30-34 << device side vlans
57
3840 PVID
sw1p2 57
sw1p2 57
3840 PVID
sw1p3 3842 PVID
sw1p4 3843 PVID
br0 None
I re-used ndo_dflt_bridge_getlink to add vlan fill call-back func.
switchdev support adds an obj dump for VLAN objects, using the same
call-back scheme as FDB dump. Support included for both compressed and
un-compressed vlan dumps.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use vid_begin/end to be consistent with BRIDGE_VLAN_INFO_RANGE_BEGIN/END.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it. And there is
no value in anyone else taking over updating it either.
However the references to it continue to spread as boiler plate text
from one Kconfig file into the next. We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.
No code is changed in this commit, just Kconfig help text.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add constants and callback functions for the dwmac on rk3368 socs.
As can be seen, the base structure is the same, only registers and
the bits in them moved slightly.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mac settings like RGMII/RMII, speeds etc are done in the so called
"General Register Files", contain numerous other settings as well and
always seem to change between Rockchip SoCs. Therefore abstract the
register accesses into a per-soc ops struct to make this reusable on
other Rockchip SoCs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first iteration of the dwmac-rk support did access an intermediate
clock directly below the pll selector. This was removed in a subsequent
revision, but the clock and one invocation remained. This results in
the driver trying to set the rate of a non-existent clock when the soc
and not some external source provides the phy clock for RMII phys.
So set the rate of the correct clock and remove the remaining now
completely unused definition.
Fixes: 436f5ae08f9d ("GMAC: add driver for Rockchip RK3288 SoCs integrated GMAC")
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a first version the driver did want to do some gpio wiggling, which
of course never made it into the kernel, but somehow these register
defines where forgotten. Remove them, as they shouldn't be here.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABCgAGBQJVhu14AAoJEP5prqPJtc/HWdEH/1m/HVExvJd8HwoDtsA+6YfC
X4m3oHMYxNvwSM2C6uh8rOxUqm/GWmhIszT7scQBt5YaeIpvGv7QTpTNe1Y6Hy7G
L75SsnVAulj69cL8sCAht1C/LNdYXdo/d/+ddvgRV6INhNXoX0P72iTn0N5C8ly7
kKFc17dq7ZP13tA7GDj2kusvn8RdqtqvZG1pioOqCvl8WSCbc/wxOEM1FecaSEYP
+rB8t0iqvPc6F7Pw7cpXhL1fGa+r+0ml3K2ZNYtw6NPzlgmroArVgoWS0KMW6U9T
G8V6llAOcGKznRQ1FLYthKFivjC3PPMr9buAx5lwo5/stkf4zRUO2lzZiQG/rFo=
=2KH+
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.1-20150621' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
Oliver Hartkopp fixed a bug in the generic CAN frame handling code, which may
lead to loss of CAN frames. It was introduced during v4.1 development.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
gpg: Signature made Sun 21 Jun 2015 09:59:36 AM PDT using RSA key ID C9B5CFC7
Zero the statistics counters when setting up the global
registers. Otherwise the counters will remain from the last boot if
the power has not been removed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the contents of the scratch registers to be shown in debugfs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device map is used to route packets between cascaded switches.
Add dumping a switches device map via debugfs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the contents of the statistics counters to be shown in debugfs.
This is particularly useful for the cpu and dsa ports, which cannot be
seen using ethtools -S.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the code to retrieve a statistics counter into a function of its
own, so it can later be reused.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dump the Address Translation Unit via a file in debugfs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the contents of the registers to be shown in debugfs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the driver understand adapter version 2.
Cc: Rachel Lunnon <rachel_lunnon@stormagic.com>
Signed-off-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If rcd length was zero, the page used for frag was not being released. It
was being replaced with a newly allocated page. This change takes care
of that memory leak.
Signed-off-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a handler for pci shutdown so that the driver has an
opportunity to make sure that device is quiesced before the PCI
switches to legacy IRQs. This way the possibility of
"screaming interrupt" is avoided.
Acked-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Macvtap should be compatible with tuntap for
maximum number of queues.
commit 'baf71c5c1f80d82e92924050a60b5baaf97e3094 (tuntap:
Increase the number of queues in tun.)' removes
the limitations and increases number of queues in tuntap.
Now, Its safe to increase number of queues in Macvtap as well.
This patch also modifies 'macvtap_del_queues' function
to avoid extra memory allocation in stack.
Changes from v1->v2 :
Michael S. Tsirkin, Jason Wang :
Better way to use linked list to
avoid use of extra memory in stack.
Sergei Shtylyov : Specify dependent commit's summary.
Signed-off-by: Pankaj Gupta <pagupta@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit edafc132ba ("xen-netback: making the bandwidth limiter runtime settable")
introduced the capability to change the bandwidth rate limit at runtime.
But it also introduced a possible crashing bug.
If netback receives two XenbusStateConnected without getting the
hotplug-status watch firing in between, then it will try to register the
watches for the rate limiter again. But this triggers a BUG() in the watch
registration code.
The fix modifies connect() to remove the possibly existing packet-rate
watches before trying to install those watches. This behaviour is in line
with how connect() deals with the hotplug-status watch.
Signed-off-by: Imre Palik <imrep@amazon.de>
Cc: Matt Wilson <msw@amazon.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-06-18
Here's the final bluetooth-next pull request for 4.2.
- Cleanups & fixes to 802.15.4 code and related drivers
- Fix btusb driver memory leak
- New USB IDs for Atheros controllers
- Support for BCM4324B3 UART based Broadcom controller
- Fix for Bluetooth encryption key size handling
- Broadcom controller initialization fixes
- Support for Intel controller DDC parameters
- Support for multiple Bluetooth LE advertising instances
- Fix for HCI user channel cleanup path
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Actor and Partner details can be accessed via proc-fs, sys-fs
entries or netlink interface. These interfaces are world readable
at this moment. The earlier patch-series made the LACP communication
secure to avoid nuisance attack from within the same L2 domain but
it did not prevent "someone unprivileged" looking at that information
on host and perform the same act.
This patch essentially avoids spitting those entries if the user
in question does not have enough privileges.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 898b2970e2 ("mvneta: implement SGMII-based in-band link state
signaling")
changed mvneta_adjust_link() so that it does not clear the auto-negotiation
bits in MVNETA_GMAC_AUTONEG_CONFIG register. This was necessary for
auto-negotiation mode to work.
Unfortunately I haven't checked if these bits are ever initialized.
It appears they are not.
This patch adds the missing initialization of the auto-negotiation bits
in the MVNETA_GMAC_AUTONEG_CONFIG register.
It fixes the following regression:
https://www.mail-archive.com/netdev@vger.kernel.org/msg67928.html
Since the patch was tested to fix a regression, it should be applied to
stable tree.
Tested-by: Arnaud Ebalard <arno@natisbad.org>
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: Florian Fainelli <f.fainelli@gmail.com>
CC: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
CC: stable@vger.kernel.org
Signed-off-by: Stas Sergeev <stsp@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the compatible string for Atmel sama5d2 SoC family as the configuration
options differ from other instances of the GEM.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8211F has different register definitions from RTL8211E.
Specially it needs to enable TXDLY in case of RGMII.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mwifiex:
* enhancements for AP mode: support verbose information in station
dump command and also information about AP link.
* enable power save by default
brcmfmac:
* fix module reload issue for PCIe
* improving msgbuf protocol for PCIe devices
* rework .get_station() cfg80211 callback operation
* determine interface combinations upon device feature support
ath9k:
* ath9k_htc: add support of channel switch
wil6210:
* add modparam for bcast ring size
* support hidden SSID
* add per-MCS Rx stats
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVglpWAAoJEG4XJFUm622bkT0H+QE/T3i44l6SEAxHEgW6Z2JP
MsAVHFV8q2jPCGfg4oCozk3fo2WPdBKwhUy7xzAg/LfxuTn0CtIzl+KuEnhsBBsx
+cNBFgBzIvHaMwfb/vxmuLK7zUROtDgOK7Kt4HF9p/Mn/JH8yTCrRy96hpnVKnuQ
h6HFO8Qx0l0pd6lbosaSPvjM8qBPy3ZfvriEHV3BTV+AXgSPWwnFkY188G2CNK5J
yYK0C2PkEX368m/qpmcbhlYrn3ZiJviiWhFmQZMW8eXe0k/pfBidXt6QGmKA7loT
p09skJk+qQtZjK4p2Hzy/3KOLU7YGFVHzww5gXqrZSxhluyhEdbOVLvKfB5jR68=
=3lke
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-06-18' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
Major changes:
mwifiex:
* enhancements for AP mode: support verbose information in station
dump command and also information about AP link.
* enable power save by default
brcmfmac:
* fix module reload issue for PCIe
* improving msgbuf protocol for PCIe devices
* rework .get_station() cfg80211 callback operation
* determine interface combinations upon device feature support
ath9k:
* ath9k_htc: add support of channel switch
wil6210:
* add modparam for bcast ring size
* support hidden SSID
* add per-MCS Rx stats
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a "param_lock" mutex to each module, and update params.c to use
the correct built-in or module mutex while locking kernel params.
Remove the kparam_block_sysfs_r/w() macros, replace them with direct
calls to kernel_param_[un]lock(module).
The kernel param code currently uses a single mutex to protect
modification of any and all kernel params. While this generally works,
there is one specific problem with it; a module callback function
cannot safely load another module, i.e. with request_module() or even
with indirect calls such as crypto_has_alg(). If the module to be
loaded has any of its params configured (e.g. with a /etc/modprobe.d/*
config file), then the attempt will result in a deadlock between the
first module param callback waiting for modprobe, and modprobe trying to
lock the single kernel param mutex to set the new module's param.
This fixes that by using per-module mutexes, so that each individual module
is protected against concurrent changes in its own kernel params, but is
not blocked by changes to other module params. All built-in modules
continue to use the built-in mutex, since they will always be loaded at
runtime and references (e.g. request_module(), crypto_has_alg()) to them
will never cause load-time param changing.
This also simplifies the interface used by modules to block sysfs access
to their params; while there are currently functions to block and unblock
sysfs param access which are split up by read and write and expect a single
kernel param to be passed, their actual operation is identical and applies
to all params, not just the one passed to them; they simply lock and unlock
the global param mutex. They are replaced with direct calls to
kernel_param_[un]lock(THIS_MODULE), which locks THIS_MODULE's param_lock, or
if the module is built-in, it locks the built-in mutex.
Suggested-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Pull x86 core updates from Ingo Molnar:
"There were so many changes in the x86/asm, x86/apic and x86/mm topics
in this cycle that the topical separation of -tip broke down somewhat -
so the result is a more traditional architecture pull request,
collected into the 'x86/core' topic.
The topics were still maintained separately as far as possible, so
bisectability and conceptual separation should still be pretty good -
but there were a handful of merge points to avoid excessive
dependencies (and conflicts) that would have been poorly tested in the
end.
The next cycle will hopefully be much more quiet (or at least will
have fewer dependencies).
The main changes in this cycle were:
* x86/apic changes, with related IRQ core changes: (Jiang Liu, Thomas
Gleixner)
- This is the second and most intrusive part of changes to the x86
interrupt handling - full conversion to hierarchical interrupt
domains:
[IOAPIC domain] -----
|
[MSI domain] --------[Remapping domain] ----- [ Vector domain ]
| (optional) |
[HPET MSI domain] ----- |
|
[DMAR domain] -----------------------------
|
[Legacy domain] -----------------------------
This now reflects the actual hardware and allowed us to distangle
the domain specific code from the underlying parent domain, which
can be optional in the case of interrupt remapping. It's a clear
separation of functionality and removes quite some duct tape
constructs which plugged the remap code between ioapic/msi/hpet
and the vector management.
- Intel IOMMU IRQ remapping enhancements, to allow direct interrupt
injection into guests (Feng Wu)
* x86/asm changes:
- Tons of cleanups and small speedups, micro-optimizations. This
is in preparation to move a good chunk of the low level entry
code from assembly to C code (Denys Vlasenko, Andy Lutomirski,
Brian Gerst)
- Moved all system entry related code to a new home under
arch/x86/entry/ (Ingo Molnar)
- Removal of the fragile and ugly CFI dwarf debuginfo annotations.
Conversion to C will reintroduce many of them - but meanwhile
they are only getting in the way, and the upstream kernel does
not rely on them (Ingo Molnar)
- NOP handling refinements. (Borislav Petkov)
* x86/mm changes:
- Big PAT and MTRR rework: making the code more robust and
preparing to phase out exposing direct MTRR interfaces to drivers -
in favor of using PAT driven interfaces (Toshi Kani, Luis R
Rodriguez, Borislav Petkov)
- New ioremap_wt()/set_memory_wt() interfaces to support
Write-Through cached memory mappings. This is especially
important for good performance on NVDIMM hardware (Toshi Kani)
* x86/ras changes:
- Add support for deferred errors on AMD (Aravind Gopalakrishnan)
This is an important RAS feature which adds hardware support for
poisoned data. That means roughly that the hardware marks data
which it has detected as corrupted but wasn't able to correct, as
poisoned data and raises an APIC interrupt to signal that in the
form of a deferred error. It is the OS's responsibility then to
take proper recovery action and thus prolonge system lifetime as
far as possible.
- Add support for Intel "Local MCE"s: upcoming CPUs will support
CPU-local MCE interrupts, as opposed to the traditional system-
wide broadcasted MCE interrupts (Ashok Raj)
- Misc cleanups (Borislav Petkov)
* x86/platform changes:
- Intel Atom SoC updates
... and lots of other cleanups, fixlets and other changes - see the
shortlog and the Git log for details"
* 'x86-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (222 commits)
x86/hpet: Use proper hpet device number for MSI allocation
x86/hpet: Check for irq==0 when allocating hpet MSI interrupts
x86/mm/pat, drivers/infiniband/ipath: Use arch_phys_wc_add() and require PAT disabled
x86/mm/pat, drivers/media/ivtv: Use arch_phys_wc_add() and require PAT disabled
x86/platform/intel/baytrail: Add comments about why we disabled HPET on Baytrail
genirq: Prevent crash in irq_move_irq()
genirq: Enhance irq_data_to_desc() to support hierarchy irqdomain
iommu, x86: Properly handle posted interrupts for IOMMU hotplug
iommu, x86: Provide irq_remapping_cap() interface
iommu, x86: Setup Posted-Interrupts capability for Intel iommu
iommu, x86: Add cap_pi_support() to detect VT-d PI capability
iommu, x86: Avoid migrating VT-d posted interrupts
iommu, x86: Save the mode (posted or remapped) of an IRTE
iommu, x86: Implement irq_set_vcpu_affinity for intel_ir_chip
iommu: dmar: Provide helper to copy shared irte fields
iommu: dmar: Extend struct irte for VT-d Posted-Interrupts
iommu: Add new member capability to struct irq_remap_ops
x86/asm/entry/64: Disentangle error_entry/exit gsbase/ebx/usermode code
x86/asm/entry/32: Shorten __audit_syscall_entry() args preparation
x86/asm/entry/32: Explain reloading of registers after __audit_syscall_entry()
...
Pull scheduler updates from Ingo Molnar:
"The main changes are:
- lockless wakeup support for futexes and IPC message queues
(Davidlohr Bueso, Peter Zijlstra)
- Replace spinlocks with atomics in thread_group_cputimer(), to
improve scalability (Jason Low)
- NUMA balancing improvements (Rik van Riel)
- SCHED_DEADLINE improvements (Wanpeng Li)
- clean up and reorganize preemption helpers (Frederic Weisbecker)
- decouple page fault disabling machinery from the preemption
counter, to improve debuggability and robustness (David
Hildenbrand)
- SCHED_DEADLINE documentation updates (Luca Abeni)
- topology CPU masks cleanups (Bartosz Golaszewski)
- /proc/sched_debug improvements (Srikar Dronamraju)"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (79 commits)
sched/deadline: Remove needless parameter in dl_runtime_exceeded()
sched: Remove superfluous resetting of the p->dl_throttled flag
sched/deadline: Drop duplicate init_sched_dl_class() declaration
sched/deadline: Reduce rq lock contention by eliminating locking of non-feasible target
sched/deadline: Make init_sched_dl_class() __init
sched/deadline: Optimize pull_dl_task()
sched/preempt: Add static_key() to preempt_notifiers
sched/preempt: Fix preempt notifiers documentation about hlist_del() within unsafe iteration
sched/stop_machine: Fix deadlock between multiple stop_two_cpus()
sched/debug: Add sum_sleep_runtime to /proc/<pid>/sched
sched/debug: Replace vruntime with wait_sum in /proc/sched_debug
sched/debug: Properly format runnable tasks in /proc/sched_debug
sched/numa: Only consider less busy nodes as numa balancing destinations
Revert 095bebf61a ("sched/numa: Do not move past the balance point if unbalanced")
sched/fair: Prevent throttling in early pick_next_task_fair()
preempt: Reorganize the notrace definitions a bit
preempt: Use preempt_schedule_context() as the official tracing preemption point
sched: Make preempt_schedule_context() function-tracing safe
x86: Remove cpu_sibling_mask() and cpu_core_mask()
x86: Replace cpu_**_mask() with topology_**_cpumask()
...
BIT value is already unsigned so casting is not necessary.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
USE_OF is used as intermediate Kconfig option by few
arch's (ARM, MIPS, Xtensa).
Replace instances of USE_OF outside of arch folders
with proper OF_???.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Manfred Schlaegl here
http://marc.info/?l=linux-netdev&m=143482089824232&w=2
commit 514ac99c64 "can: fix multiple delivery of a single CAN frame for
overlapping CAN filters" requires the skb->tstamp to be set to check for
identical CAN skbs.
As net timestamping is influenced by several players (netstamp_needed and
netdev_tstamp_prequeue) Manfred missed a proper timestamp which leads to
CAN frame loss.
As skb timestamping became now mandatory for CAN related skbs this patch
makes sure that received CAN skbs always have a proper timestamp set.
Maybe there's a better solution in the future but this patch fixes the
CAN frame loss so far.
Reported-by: Manfred Schlaegl <manfred.schlaegl@gmx.at>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Following patch contains changes in liquidio Kconfig for
selecting LIBCRC32C.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no reason to perform a buffer copy for the firmware name. This
also avoids a (currently impossible with current callers) NULL dereference
if there was no matching firmware.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Append 0x to all %x in order to avoid while reading when there is other
decimal value in the log.
Also replace some of the hexadecimal print to decimal to uniformize the
format with netfront.
Signed-off-by: Julien Grall <julien.grall@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: netdev@vger.kernel.org
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variables old_req_cons and ring_slots_used are assigned but never
used since commit 1650d5455b "xen-netback:
always fully coalesce guest Rx packets".
Signed-off-by: Julien Grall <julien.grall@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
rx->status is an int16_t, print it using %d rather than %u in order to
have a meaningful value when the field is negative.
Also use %u rather than %x for rx->offset.
Signed-off-by: Julien Grall <julien.grall@citrix.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains a final Netfilter pull request for net-next
4.2. This mostly addresses some fallout from the previous pull request, small
netns updates and a couple of new features for nfnetlink_log and the socket
match that didn't get in time for the previous pull request. More specifically
they are:
1) Add security context information to nfnetlink_queue, from Roman Kubiak.
2) Add support to restore the sk_mark into skb->mark through xt_socket,
from Harout Hedeshian.
3) Force alignment of 16 bytes of per cpu xt_counters, from Eric Dumazet.
4) Rename br_netfilter.c to br_netfilter_hooks.c to prepare split of IPv6 code
into a separated file.
5) Move the IPv6 code in br_netfilter into a separated file.
6) Remove unused RCV_SKB_FAIL() in nfnetlink_queue and nfetlink_log, from Eric
Biederman.
7) Two liner to simplify netns logic in em_ipset_match().
8) Add missing includes to net/net_namespace.h to avoid compilation problems
that result from not including linux/netfilter.h in netns headers.
9) Use a forward declaration instead of including linux/proc_fs.h from
netns/netfilter.h
10) Add a new linux/netfilter_defs.h to replace the linux/netfilter.h inclusion
in netns headers.
11) Remove spurious netfilter.h file included in the net tree, also from Eric
Biederman.
12) Fix x_tables compilation warnings on 32 bits platforms that resulted from
recent changes in x_tables counters, from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing my netfilter changes I noticed several files where
recompiling unncessarily because they unncessarily included
netfilter.h.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Jeff Kirsher says:
====================
This series contains updates to fm10k only.
Alex provides two fixes for the fm10k, first folds the fm10k_pull_tail()
call into fm10k_add_rx_frag(), this way the fragment does not have to be
modified after it is added to the skb. The second fixes missing braces
to an if statement.
The remaining patches are from Jacob which contain improvements and fixes
for fm10k. First fix makes it so that invalid address will simply be
skipped and allows synchronizing the full list to proceed with using
iproute2 tool. Fixed a possible kernel panic by using the correct
transmit timestamp function. Simplified the code flow for setting the
IN_PROGRESS bit of the shinfo for an skb that we will be timestamping.
Fix a bug in the timestamping transmit enqueue code responsible for a
NULL pointer dereference and invalid access of the skb list by freeing
the clone in the cases where we did not add it to the queue. Update the
PF code so that it resets the empty TQMAP/RQMAP regirsters post-VFLR to
prevent innocent VF drivers from triggering malicious driver events.
The SYSTIME_CFG.Adjust direction bit is actually supposed to indicate
that the adjustment is positive, so fix the code to align correctly with
the hardware and documentation. Cleanup local variable that is no longer
used after a previous refactor of the code. Fix the code flow so that we
actually clear the enabled flag as part of our removal of the LPORT.
v2:
- updated patch 07 description based on feedback from Sergei Shtylyov
- updated patch 09 & 10 to use %d in error message based on feedback
from Sergei Shtylyov
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
These kind of informations are only useful for debugging and should not be
displayed in normal modules message.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reviewing the code I noticed that one of the commits added an if
statement followed by a for loop, but the if statement was missing the
braces around the loop. This change corrects the coding style error.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a VF issues an LPORT_STATE request to enable a port that is already
enabled, the PF will first disable the VF LPORT. Then it should
re-enable the VF again with the new requested settings. This ensures
that any switch rules are cleared by deleting the LPORT on the switch.
However, the flow is bugged because we actually check if the VF is
enabled at the end, and thus don't re-enable it. Fix the flow so that we
actually clear the enabled flags as part of our removal of the LPORT.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The reference to err_no was left around after a previous code refactor.
We never use the value, and it doesn't seem to be used in side a hidden
macro reference. Discovered via cppcheck.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The SYSTIME_CFG.Adjust Direction bit is actually supposed to indicate
that the adjustment is positive. Fix the code to align correctly with
hardware and documentation.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the __attribute__((packed)) indicator to some structures
which are overlayed onto a TLV message. These structures must be packed
as small as possible in order to correctly align when copied into the
mailbox buffer. Without doing so, the receiving mailbox code incorrectly
parses the values and we get invalid message responses from the switch
manager software.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During initialization, the VF counts its rings by walking the TQDLOC
registers. This works only if the TQMAP/RQMAP registers are set to map
all of the out-of-bound rings back to the first one. This allows the VF
to cleanly detect when it has run out of queues. Update the PF code so
that it resets the empty TQMAP/RQMAP registers post-VFLR to prevent
innocent VF drivers from triggering malicious driver events.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, we don't notify the switch at all when the PF
administratively sets a new VLAN or MAC address. This causes the old
addresses to remain valid on the switch table. Since the PF is
overriding any configuration done directly by the VF, we choose to
simply re-create the LPORT for the VF. This does mean that all rules for
the VF will be dropped when we set something directly via the PF, but it
prevents some weird issues where the MAC/VLAN table retains some stale
configuration.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up the use of dma_get_required_mask and uses the
simpler dma_set_mask_and_coherent function instead of doing these as
separate steps.
I removed the dma_get_required_mask call because based on some minimal
testing it appears that either (a) we're not doing the right thing with
the call or (b) we don't need it anyways. If the value returned is
<48bits, we'll end up trying with 48 bits anyways. If it's over 48bits,
fm10k can't support that anyways, and we should try 48bits. If 48bits
fails, we'll fallback to 32bits. This cleans up some very funky code.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Also use %d for error values, since printing in hexadecimal is probably
not helpful.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
l2_accel was checked for NULL at the top of fm10k_dfwd_del_station, and
we return if it is not defined. Due to this, we already know it can't be
null here so a separate check is meaningless. Discovered via cppcheck.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The value will never be negative, and we use the %u print format. Thus,
use unsigned int for the loop counter. Issue found using cppcheck.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This prevents a memory leak in fm10k_set_ringparams. The leak occurs
because we go down, change ring parameters, and then come up. However,
fm10k_down on its own is not clearing the Rx rings. Since fm10k_up
assumes the rings are clean we basically drop the buffers and leak a
bunch of memory. Eventually we hit dirty page faults and reboot the
system. This issue does not occur elsewhere because other flows that
involve fm10k_down go through fm10k_close which immediately called
fm10k_free_all_rx_resources which properly cleans the rings.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch resolves a bug in the ts_tx_enqueue code responsible for a
NULL pointer dereference and invalid access of the skb list. We
incorrectly freed the actual skb we found instead of our copy. Thus the
skb queue is essentially invalidated. Resolve this by freeing our clone
in the cases where we did not add it to the queue. This also avoids the
skb memory leak caused by failure to free the clone.
[ 589.719320] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 589.722344] IP: [<ffffffffa0310e60>] fm10k_ts_tx_subtask+0xb0/0x160 [fm10k]
[ 589.723796] PGD 0
[ 589.725228] Oops: 0000 [#1] SMP
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch simplifies the code flow for setting the IN_PROGRESS bit of
the shinfo for an skb we will be timestamping.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Yuval Mintz