MFC variant data replaces various macros used in the driver
which will change in a different version of MFC hardware.
Also does a cleanup of MFC context structure and common files.
Signed-off-by: Jeongtae Park <jtp.park@samsung.com>
Signed-off-by: Janghyuck Kim <janghyuck.kim@samsung.com>
Signed-off-by: Jaeryul Oh <jaeryul.oh@samsung.com>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Modifies the driver to use a callback based architecture
for hardware dependent calls. This architecture is suitable
for supporting co-existence with newer versions of MFC hardware.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patch renames hardware specific opr and cmd files to
opr_v5 and cmd_v5 respectively. This is done for accomodating
firmware v6. Also the shared memory management files are removed
and the functionality is added to the opr_v5 file.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Depending on the sensor configuration it might be required to adjust
the CSIS's output pixel clock so it is greater than its input pixel
clock, in order to avoid the input data FIFO overflow.
Use platform data to select SCLK_CSIS clock from CMU as a source, rather
than CSI APB clock.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The phy_enable callback is common for all Samsung SoC platforms,
replace it with direct function call so the MIPI-CSI2 DPHY control
is also possible on device tree instantiated platforms.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rename the regulator supply names to more meaningful ones.
It's a prerequisite for adding device tree support.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
set device_caps and also change the driver and
bus_info to proper values as per standard.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
from commit with id 896f38f582
it's mandatory to check the return code of vb2_queue_init().
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
vpif_display relied on a 1-1 mapping of output and subdev. This is not
necessarily the case. Separate the two. So there is a list of subdevs
and a list of outputs. Each output refers to a subdev and has routing
information. An output does not have to have a subdev.
The initial output for each channel is set to the fist output.
Currently missing is support for associating multiple subdevs with
an output.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
struct vpif_interface is channel specific, not subdev specific.
Move it to the channel config.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This makes it easier to have outputs without subdevs.
This needs more work. The way the outputs are configured should be identical
to how inputs are configured.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
vpif_capture relied on a 1-1 mapping of input and subdev. This is not
necessarily the case. Separate the two. So there is a list of subdevs
and a list of inputs. Each input refers to a subdev and has routing
information. An input does not have to have a subdev.
The initial input for each channel is set to the fist input.
Currently missing is support for associating multiple subdevs with
an input.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cleanup sequence was incorrect and could cause a kernel oops.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cleanup sequence was incorrect and could cause a kernel oops.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When device nodes are registered they must be ready for use
immediately, so make sure the subdevs are loaded first.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When device nodes are registered they must be ready for use
immediately, so make sure the subdevs are loaded first.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Routing information is a property of the input, not of the subdev.
One subdev may provide multiple inputs, each with its own routing
information.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Calling a subdev op that isn't implemented will just return -ENOIOCTLCMD
No need to have a flag for that.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The output index does not belong to video_obj, it belongs to
channel_obj. Also rename to output_idx to be consistent with
the input_idx name used in vpif_capture.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
input_idx does not belong to video_obj. Move it where it belongs.
Also remove the bogus code in the open() function that suddenly
changes the input to 0 for no reason.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
for da850/omap-l138, there is no need to setup_input_channel_mode()
and set_clock(), to avoid adding dummy code in board file just returning
zero add a check in the driver itself to call the handler only if its
not NULL.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/platform/fsl-viu.c: In function 'vidioc_s_fbuf':
drivers/media/platform/fsl-viu.c:867:32: warning: initialization discards 'const' qualifier from pointer target type [enabled by default]
This is fall-out from this commit:
commit e6eb28c220
Author: Hans Verkuil <hans.verkuil@cisco.com>
[media] v4l2: make vidioc_s_fbuf const
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The V4L2_PIX_FMT_S5C_YUYV_JPG image formats consists of 2 planes, the
first containing interleaved JPEG/YUYV data and the second containing
meta data describing the interleaving method.
The image data is transferred with MIPI-CSI "User Defined Byte-Based
Data 1" type and is captured to memory by FIMC DMA engine.
The meta data is transferred using MIPI-CSI2 "Embedded 8-bit non Image
Data" and it is captured in the MIPI-CSI slave device and copied to
the bridge provided buffer.
To make sure the size of allocated buffers is correct for the subdevs
configuration when VIDIOC_STREAMON ioctl is invoked, an additional
check is added at the video pipeline validation function.
Flag FMT_FLAGS_COMPRESSED indicates the buffer size must be retrieved
from a sensor subdev.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
MIPI-CSI has internal memory mapped buffers for the frame embedded
(non-image) data. There are two buffers, for even and odd frames which
need to be saved after an interrupt is raised. The packet data buffers
size is 4 KiB and there is no status register in the hardware where the
actual non-image data size can be read from. Hence the driver copies
whole packet data buffer into a buffer provided by the FIMC driver.
This will form a separate plane in the user buffer.
When FIMC DMA engine is stopped by the driver due the to user space
not keeping up with buffer de-queuing the MIPI-CSIS will still run,
however it must discard data which is not captured by FIMC. Which
frames are actually capture by MIPI-CSIS is determined by means of
the s_tx_buffer subdev callback. When it is not called after a single
embedded data frame has been captured and copied and before next
embedded data frame interrupt occurrs, subsequent embedded data frames
will be dropped.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/platform/s5p-fimc/fimc-m2m.c:561:2: warning: passing argument 2 of 'fimc_m2m_try_crop' discards 'const' qualifier from pointer target type [enabled by default]
drivers/media/platform/s5p-fimc/fimc-m2m.c:502:12: note: expected 'struct v4l2_crop *' but argument is of type 'const struct v4l2_crop *'
This is fall-out from this commit:
commit 4f996594ce
Author: Hans Verkuil <hans.verkuil@cisco.com>
[media] v4l2: make vidioc_s_crop const
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/platform/s5p-g2d/g2d.c:535:2: warning: passing argument 3 of 'vidioc_try_crop' discards 'const' qualifier from pointer target type [enabled by default]
drivers/media/platform/s5p-g2d/g2d.c:510:12: note: expected 'struct v4l2_crop *' but argument is of type 'const struct v4l2_crop *'
This is fall-out from this commit:
commit 4f996594ce
Author: Hans Verkuil <hans.verkuil@cisco.com>
[media] v4l2: make vidioc_s_crop const
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert clk_enable/clk_disable to clk_prepare_enable/clk_disable_unprepare
calls as required by common clock framework.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch replaces V4L2_OUT_CAP_CUSTOM_TIMINGS macro with
V4L2_OUT_CAP_DV_TIMINGS. As V4L2_OUT_CAP_CUSTOM_TIMINGS is being phased
out.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
recent patch with commit id 4f996594ce
which makes vidioc_s_crop const, was causing a following build warning,
vpbe_display.c: In function 'vpbe_display_s_crop':
vpbe_display.c:640: warning: initialization discards qualifiers from pointer target type
This patch fixes the above build warning.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch replaces the preset API by the timings API, and
appropriate changes in board file.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
recent patch with commit id 4f996594ce
which makes vidioc_s_crop const, was causing a following build error.
vpfe_capture.c: In function 'vpfe_s_crop':
vpfe_capture.c:1695: error: assignment of read-only location '*crop'
vpfe_capture.c:1706: warning: passing argument 1 of
'ccdc_dev->hw_ops.set_image_window' discards qualifiers from pointer target type
vpfe_capture.c:1706: note: expected 'struct v4l2_rect *' but argument is of
type 'const struct v4l2_rect *'
make[4]: *** [drivers/media/platform/davinci/vpfe_capture.o] Error 1
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The mixer video node supports only multi-planar API so the driver
should not be setting V4L2_CAP_VIDEO_OUTPUT flags. Fix this and
also switch to device_caps. Additionally fix the VIDIOC_ENUM_FMT
ioctl handler which now works for V4L2_BUF_TYPE_CAPTURE, rather
than expected V4L2_BUF_TYPE_CAPTURE_MPLANE.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
return statement was wrongly placed before a code that needs to be
executed. Moved the return statement to the end of the function.
Tested suspend/resume on SMDK4412 board using 3.5-rc6 kernel.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes the following warnings:
drivers/media/platform/exynos-gsc/gsc-core.c:313:5: warning:
symbol 'get_plane_info' was not declared. Should it be static?
drivers/media/platform/exynos-gsc/gsc-core.c:746:28: warning:
symbol 'gsc_ctrl_ops' was not declared. Should it be static?
drivers/media/platform/exynos-gsc/gsc-m2m.c:102:5: warning:
symbol 'gsc_fill_addr' was not declared. Should it be static?
drivers/media/platform/exynos-gsc/gsc-m2m.c:252:16: warning:
symbol 'gsc_m2m_qops' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
version.h is not needed for these files.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When mdev is NULL, the error print statement will try to dereference
the NULL pointer.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All code setting/clearing working context bits has been moved
to separate functions. set_bit/clear_bit have been replaced by
non-atomic variants - variable is already guarded by spin_lock.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
s5p-mfc encoder after receiving V4L2_ENC_CMD_STOP command
will instruct MFC device to release all encoded frames.
After dequeuing last encoded frame driver will generate
V4L2_EVENT_EOS event.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use a copy of sensor platform data structure, rather than referencing
external platform data from the driver. This allows to fill the local
copy with values parsed from device tree when needed.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add hardware event/error counters which can be dumped into the kernel
log through VIDIOC_LOG_STATUS ioctl. The counters are reset in each
s_stream(1) call. Any errors are logged after streaming is turned off.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Silences the following warnings:
WARNING: sizeof *ctx should be sizeof(*ctx)
WARNING: sizeof *dev should be sizeof(*dev)
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In order to reuse the FIMC-LITE module on Exynos4 and Exynos5
SoC introduce a set of callbacks for the media pipeline control
from within FIMC/FIMC-LITE video node. It lets us avoid symbol
dependencies between FIMC-LITE and the whole media device driver,
which simplifies the initialization sequences and doesn't
introduce issues preventing common kernel image for exynos4 and
exynos5 SoCs.
This patch also corrects following build errors:
drivers/built-in.o: In function `buffer_queue':
drivers/media/video/s5p-fimc/fimc-lite.c:414: undefined reference
to `fimc_pipeline_s_stream'
drivers/built-in.o: In function `fimc_lite_resume':
drivers/media/video/s5p-fimc/fimc-lite.c:1518: undefined reference
to `fimc_pipeline_initialize'
drivers/built-in.o: In function `fimc_lite_suspend':
drivers/media/video/s5p-fimc/fimc-lite.c:1544: undefined reference
to `fimc_pipeline_shutdown'
when only CONFIG_VIDEO_EXYNOS_FIMC_LITE is selected, without
CONFIG_VIDEO_S5P_FIMC.
Reported-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jeongtae Park