_omap2_clksel_get_src_field() was returning the first entry which was
either the default _or_ applicable to the SoC. This is wrong - we
should be returning the first default which is applicable to the SoC.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The error checks for omap2_divisor_to_clksel() and comment disagree with
the actual value returned on error. Fix this to return the correct error
value.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Between 2.6.23 and 2.6.24-rc1 a change was made that broke IBM LS21
systems that had the HPET enabled in the BIOS, resulting in boot hangs
for x86_64.
Specifically commit b8ce335906, which
merges the i386 and x86_64 HPET code.
Prior to this commit, when we setup the HPET timers in x86_64, we did
the following:
hpet_writel(HPET_TN_ENABLE | HPET_TN_PERIODIC | HPET_TN_SETVAL |
HPET_TN_32BIT, HPET_T0_CFG);
However after the i386/x86_64 HPET merge, we do the following:
cfg = hpet_readl(HPET_Tn_CFG(timer));
cfg |= HPET_TN_ENABLE | HPET_TN_PERIODIC |
HPET_TN_SETVAL | HPET_TN_32BIT;
hpet_writel(cfg, HPET_Tn_CFG(timer));
However on LS21s with HPET enabled in the BIOS, the HPET_T0_CFG register
boots with Level triggered interrupts (HPET_TN_LEVEL) enabled. This
causes the periodic interrupt to be not so periodic, and that results in
the boot time hang I reported earlier in the delay calibration.
My fix: Always disable HPET_TN_LEVEL when setting up periodic mode.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix the VSX alignment handler for VSX registers > 32. 32-63 are stored
in the VMX part of the thread_struct not the FPR part.
Signed-off-by: Michael Neuling <mikey@neuling.org>
CC: stable@kernel.org (2.6.27 & .28 please)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Change the PS3 hotplug memory routine ps3_mm_add_memory() from
a core_initcall to a device_initcall.
core_initcall routines run before the powerpc topology_init()
startup routine, which is a subsys_initcall, resulting in
failure of ps3_mm_add_memory() when CONFIG_NUMA=y. When
ps3_mm_add_memory() fails the system will boot with just the
128 MiB of boot memory
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix the powerpc NUMA reserve bootmem page selection logic.
commit 8f64e1f2d1 (powerpc: Reserve
in bootmem lmb reserved regions that cross NUMA nodes) changed
the logic for how the powerpc LMB reserved regions were converted
to bootmen reserved regions. As the folowing discussion reports,
the new logic was not correct.
mark_reserved_regions_for_nid() goes through each LMB on the
system that specifies a reserved area. It searches for
active regions that intersect with that LMB and are on the
specified node. It attempts to bootmem-reserve only the area
where the active region and the reserved LMB intersect. We
can not reserve things on other nodes as they may not have
bootmem structures allocated, yet.
We base the size of the bootmem reservation on two possible
things. Normally, we just make the reservation start and
stop exactly at the start and end of the LMB.
However, the LMB reservations are not aware of NUMA nodes and
on occasion a single LMB may cross into several adjacent
active regions. Those may even be on different NUMA nodes
and will require separate calls to the bootmem reserve
functions. So, the bootmem reservation must be trimmed to
fit inside the current active region.
That's all fine and dandy, but we trim the reservation
in a page-aligned fashion. That's bad because we start the
reservation at a non-page-aligned address: physbase.
The reservation may only span 2 bytes, but that those bytes
may span two pfns and cause a reserve_size of 2*PAGE_SIZE.
Take the case where you reserve 0x2 bytes at 0x0fff and
where the active region ends at 0x1000. You'll jump into
that if() statment, but node_ar.end_pfn=0x1 and
start_pfn=0x0. You'll end up with a reserve_size=0x1000,
and then call
reserve_bootmem_node(node, physbase=0xfff, size=0x1000);
0x1000 may not be on the same node as 0xfff. Oops.
In almost all the vm code, end_<anything> is not inclusive.
If you have an end_pfn of 0x1234, page 0x1234 is not
included in the range. Using PFN_UP instead of the
(>> >> PAGE_SHIFT) will make this consistent with the other VM
code.
We also need to do math for the reserved size with physbase
instead of start_pfn. node_ar.end_pfn << PAGE_SHIFT is
*precisely* the end of the node. However,
(start_pfn << PAGE_SHIFT) is *NOT* precisely the beginning
of the reserved area. That is, of course, physbase.
If we don't use physbase here, the reserve_size can be
made too large.
From: Dave Hansen <dave@linux.vnet.ibm.com>
Tested-by: Geoff Levand <geoffrey.levand@am.sony.com> Tested on PS3.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix _PAGE_CHG_MASK so that pte_modify() does not affect the _PAGE_SPECIAL bit.
Signed-off-by: Philippe Gerum <rpm@xenomai.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Impact: Flush the lazy MMU only once
Pending mmu updates only need to be flushed once to bring the
in-memory pagetable state up to date.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Impact: Catch cases where lazy MMU state is active in a preemtible context
arch_flush_lazy_mmu_cpu() has been changed to disable preemption so
the checks in enter/leave will never trigger. Put the preemtible()
check into arch_flush_lazy_mmu_cpu() to catch such cases.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Impact: avoid access to percpu vars in preempible context
They are intended to be used whenever there's the possibility
that there's some stale state which is going to be overwritten
with a queued update, or to force a state change when we may be
in lazy mode. Either way, we could end up calling it with
preemption enabled, so wrap the functions in their own little
preempt-disable section so they can be safely called in any
context (though preemption should never be enabled if we're actually
in a lazy state).
(Move out of line to avoid #include dependencies.)
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Jeff Mahoney reported:
> With Suse's hwinfo tool, on -tip:
> WARNING: at arch/x86/mm/pat.c:637 reserve_pfn_range+0x5b/0x26d()
reserve_pfn_range() is not tracking the memory range below 1MB
as non-RAM and as such is inconsistent with similar checks in
reserve_memtype() and free_memtype()
Rename the pagerange_is_ram() to pat_pagerange_is_ram() and add the
"track legacy 1MB region as non RAM" condition.
And also, fix reserve_pfn_range() to return -EINVAL, when the pfn
range is RAM. This is to be consistent with this API design.
Reported-and-tested-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix race leading to crash under KVM and Xen
The CPA code may be called while we're in lazy mmu update mode - for
example, when using DEBUG_PAGE_ALLOC and doing a slab allocation
in an interrupt handler which interrupted a lazy mmu update. In this
case, the in-memory pagetable state may be out of date due to pending
queued updates. We need to flush any pending updates before inspecting
the page table. Similarly, we must explicitly flush any modifications
CPA may have made (which comes down to flushing queued operations when
flushing the TLB).
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Stable Kernel <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timers: fix TIMER_ABSTIME for process wide cpu timers
timers: split process wide cpu clocks/timers, fix
x86: clean up hpet timer reinit
timers: split process wide cpu clocks/timers, remove spurious warning
timers: split process wide cpu clocks/timers
signal: re-add dead task accumulation stats.
x86: fix hpet timer reinit for x86_64
sched: fix nohz load balancer on cpu offline
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ptrace, x86: fix the usage of ptrace_fork()
i8327: fix outb() parameter order
x86: fix math_emu register frame access
x86: math_emu info cleanup
x86: include correct %gs in a.out core dump
x86, vmi: put a missing paravirt_release_pmd in pgd_dtor
x86: find nr_irqs_gsi with mp_ioapic_routing
x86: add clflush before monitor for Intel 7400 series
x86: disable intel_iommu support by default
x86: don't apply __supported_pte_mask to non-present ptes
x86: fix grammar in user-visible BIOS warning
x86/Kconfig.cpu: make Kconfig help readable in the console
x86, 64-bit: print DMI info in the oops trace
Ptrace_detach() races with __ptrace_unlink() if the traced task is
reaped while detaching. This might cause a double-free of the BTS
buffer.
Change the ptrace_detach() path to only do the memory accounting in
ptrace_bts_detach() and leave the buffer free to ptrace_bts_untrace()
which will be called from __ptrace_unlink().
The fix follows a proposal from Oleg Nesterov.
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The vdso_per_cpu_data entry in the lowcore structure uses __u32
instead of __u64. If the data page is above 4GB the pointer is
truncated and the kernel crashes.
Reported-by: Mijo Safradin <mijo@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The constraint used for retrieving and restoring the parent function
pointer is incorrect. The parent variable is a pointer, and the
address of the pointer is modified by the asm statement and not
the pointer itself. It is incorrect to pass it in as an output
constraint since the asm will never update the pointer.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The following commit:
commit 64b3d0e812
Author: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Date: Thu Dec 18 19:13:51 2008 +0000
powerpc/mm: Rework usage of _PAGE_COHERENT/NO_CACHE/GUARDED
broke setting of the _PAGE_COHERENT bit in the PPC HW PTE. Since we now
actually set _PAGE_COHERENT in the Linux PTE we shouldn't be clearing it
out before we propogate it to the PPC HW PTE.
Reported-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] AACI: timeout will reach -1
[ARM] Storage class should be before const qualifier
[ARM] pxa: stop and disable IRQ for each DMA channels at startup
[ARM] pxa: make more SSCR0 bit definitions visible on multiple processors
[ARM] pxa: fix missing of __REG() definition for ac97 registers access
[ARM] pxa: fix NAND and MMC clock initialization for pxa3xx
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Add missing sparsemem.h include
powerpc/pci: mmap anonymous memory when legacy_mem doesn't exist
powerpc/cell: Add missing #include for oprofile
powerpc/ftrace: Fix math to calculate offset in TOC
powerpc: Don't emulate mr. instructions
powerpc/fsl-booke: Fix mapping functions to use phys_addr_t
arch/powerpc: Eliminate double sizeof
powerpc/cpm2: Fix set interrupt type
powerpc/83xx: Fix TSEC0 workability on MPC8313E-RDB boards
powerpc/83xx: Fix missing #{address,size}-cells in mpc8313erdb.dts
powerpc/83xx: Build breakage for CONFIG_PM but no CONFIG_SUSPEND
Impact: fix to prevent a kernel crash on fault
If for some reason the pointer to the parent function on the
stack takes a fault, the fix up code will not return back to
the original faulting code. This can lead to unpredictable
results and perhaps even a kernel panic.
A fault should not happen, but if it does, we should simply
disable the tracer, warn, and continue running the kernel.
It should not lead to a kernel crash.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
In i8237A_resume(), when resetting the DMA controller, the parameters to
dma_outb() were mixed up.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
[ cleaned up the file a tiny bit. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning of the
declaration specifiers in a declaration is an obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/powerpc/platforms/pseries/hotplug-memory.c uses
remove_section_mapping() but doesn't include sparsemem.h which defines
it. This can cause compilation fails for some configs.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The new legacy_mem file in sysfs is causing problems with X on machines
that don't support legacy memory access. The way I initially implemented
it, we would fail with -ENXIO when trying to mmap it, thus exposing to
X that we do support the API but there is no legacy memory.
Unfortunately, X poor error handling is causing it to fail to start when
it gets this error.
This implements a workaround hack that instead maps anonymous memory
instead (using shmem if VM_SHARED is set, just like /dev/zero does).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch/powerpc/oprofile/cell/spu_profiler.c is missing a asm/time.h
include which is required for ppc_proc_freq. This can cause compile
failures for some config combinations.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Impact: fix dynamic ftrace with large modules in PPC64
The math to calculate the offset into the TOC that is taken from reading
the trampoline is incorrect. The bottom half of the offset is a signed
extended short. The current code was using an OR to create the offset
when it should have been using an addition.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently emulate_step() emulates mr. instructions without updating cr0
and this can be disastrous. Don't emulate mr.
This bug has been around for a while, but I am not sure if its a worthy
-stable candidate. I'll leave it to Ben do decide.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fixed v_mapped_by_tlbcam() and p_mapped_by_tlbcam() to use phys_addr_t
instead of unsigned long. In 36-bit physical mode we really need these
functions to deal with phys_addr_t when trying to match a physical
address or when returning one.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
do_device_not_available() is the handler for #NM and it declares that
it takes a unsigned long and calls math_emu(), which takes a long
argument and surprisingly expects the stack frame starting at the zero
argument would match struct math_emu_info, which isn't true regardless
of configuration in the current code.
This patch makes do_device_not_available() take struct pt_regs like
other exception handlers and initialize struct math_emu_info with
pointer to it and pass pointer to the math_emu_info to math_emulate()
like normal C functions do. This way, unless gcc makes a copy of
struct pt_regs in do_device_not_available(), the register frame is
correctly accessed regardless of kernel configuration or compiler
used.
This doesn't fix all math_emu problems but it at least gets it
somewhat working.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] powernow-k8: Get transition latency from ACPI _PSS table
[CPUFREQ] Make ignore_nice_load setting of ondemand work as expected.
Architectures other than mips and x86 are not using ticket spinlocks.
Therefore, the contention on the lock is meaningless, since there is
nobody known to be waiting on it (arguably /fairly/ unfair locks).
Dummy it out to return 0 on other architectures.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: cleanup
* Come on, struct info? s/struct info/struct math_emu_info/
* Use struct pt_regs and kernel_vm86_regs instead of defining its own
register frame structure.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: dump the correct %gs into a.out core dump
aout_dump_thread() read %gs but didn't include it in core dump. Fix
it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit 6194ba6ff6 ("x86: don't special-case
pmd allocations as much") made changes to the way we handle pmd allocations,
and while doing that it dropped a call to paravirt_release_pd on the
pgd page from the pgd_dtor code path.
As a result of this missing release, the hypervisor is now unaware of the
pgd page being freed, and as a result it ends up tracking this page as a
page table page.
After this the guest may start using the same page for other purposes, and
depending on what use the page is put to, it may result in various performance
and/or functional issues ( hangs, reboots).
Since this release is only required for VMI, I now release the pgd page from
the (vmi)_pgd_free hook.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: <stable@kernel.org>
Impact: find right nr_irqs_gsi on some systems.
One test-system has gap between gsi's:
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 0, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: IOAPIC (id[0x05] address[0xfeafd000] gsi_base[48])
[ 0.000000] IOAPIC[1]: apic_id 5, version 0, address 0xfeafd000, GSI 48-54
[ 0.000000] ACPI: IOAPIC (id[0x06] address[0xfeafc000] gsi_base[56])
[ 0.000000] IOAPIC[2]: apic_id 6, version 0, address 0xfeafc000, GSI 56-62
...
[ 0.000000] nr_irqs_gsi: 38
So nr_irqs_gsi is not right. some irq for MSI will overwrite with io_apic.
need to get that with acpi_probe_gsi when acpi io_apic is used
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
For Intel 7400 series CPUs, the recommendation is to use a clflush on the
monitored address just before monitor and mwait pair [1].
This clflush makes sure that there are no false wakeups from mwait when the
monitored address was recently written to.
[1] "MONITOR/MWAIT Recommendations for Intel Xeon Processor 7400 series"
section in specification update document of 7400 series
http://download.intel.com/design/xeon/specupdt/32033601.pdf
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This is based upon a report from Chris Torek and his initial patch.
From Chris's report:
--------------------
This came up in testing kgdb, using the built-in tests -- turn
on CONFIG_KGDB_TESTS, then
echo V1 > /sys/module/kgdbts/parameters/kgdbts
-- but it would affect using kgdb if you were debugging and looking
at bad pointers.
--------------------
When we get a copy_{from,to}_user() request and the %asi is set to
something other than ASI_AIUS (which is userspace) then we branch off
to a routine called memcpy_user_stub(). It just does a straight
memcpy since we are copying from kernel to kernel in this case.
The logic was that since source and destination are both kernel
pointers we don't need to have exception checks.
But for what probe_kernel_{read,write}() is trying to do, we have to
have the checks, otherwise things like kgdb bad kernel pointer
accesses don't do the right thing.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an implementation of a suggestion made by Chris Torek:
--------------------
Something else I noticed in passing: the EX and EX_LD/EX_ST macros
scattered throughout the various .S files make a fair bit of .fixup
code, all of which does the same thing. At the cost of one symbol
in copy_in_user.S, you could just have one common two-instruction
retl-and-mov-1 fixup that they all share.
--------------------
The following is with a defconfig build:
text data bss dec hex filename
3972767 344024 584449 4901240 4ac978 vmlinux.orig
3968887 344024 584449 4897360 4aba50 vmlinux
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI PM: make the PM core more careful with drivers using the new PM framework
PCI PM: Read power state from device after trying to change it on resume
PCI PM: Do not disable and enable bridges during suspend-resume
PCI: PCIe portdrv: Simplify suspend and resume
PCI PM: Fix saving of device state in pci_legacy_suspend
PCI PM: Check if the state has been saved before trying to restore it
PCI PM: Fix handling of devices without drivers
PCI: return error on failure to read PCI ROMs
PCI: properly clean up ASPM link state on device remove
One of my past fixes to this code introduced a different new bug.
When using 32-bit "int $0x80" entry for a bogus syscall number,
the return value is not correctly set to -ENOSYS. This only happens
when neither syscall-audit nor syscall tracing is enabled (i.e., never
seen if auditd ever started). Test program:
/* gcc -o int80-badsys -m32 -g int80-badsys.c
Run on x86-64 kernel.
Note to reproduce the bug you need auditd never to have started. */
#include <errno.h>
#include <stdio.h>
int
main (void)
{
long res;
asm ("int $0x80" : "=a" (res) : "0" (99999));
printf ("bad syscall returns %ld\n", res);
return res != -ENOSYS;
}
The fix makes the int $0x80 path match the sysenter and syscall paths.
Reported-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: Roland McGrath <roland@redhat.com>
the FPGA on the TS-7800 provides access to a number of devices
and so we have to be careful when reprogramming it. As we
are effectively turning a bus off/on we have to inform the
kernel that it should stop using anything provided by the
FPGA (currently only the RTC however the NAND, LCD, etc is
to come) before it's reprogrammed.
Once reprogramed, we can tell the kernel to (re)enable things
by checking the FPGA ID against a lookup table for what a
particular FPGA bitstream can provide.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
The TS-7800's M25P40 is not available to the kernel, it's used
to load the initial bitstream onto the FPGA and so these hooks
point to nothing and need to be removed.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Taking sizeof the result of sizeof is quite strange and does not seem to be
what is wanted here.
This was fixed using the following semantic patch.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression E;
@@
- sizeof (
sizeof (E)
- )
@@
type T;
@@
- sizeof (
sizeof (T)
- )
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is a simple change to correct problems when using set_irq_type
on platforms using CPM2. This code corrects the problem on most platform
but may have issues on 8272 derived platforms for some interrupts.
On 8272 PC2 & 3 are missing and PC 23 & 29 are added, which this patch
does not address.
Signed-off-by: Paul Bilke <paul@conspiracy.net>
Reviewed-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
TSEC0 is connected to Vitesse 7385 5-port switch. The switch
isn't connected to any mdio bus, the link to the switch is fixed
to Full-duplex 1000 Mb/s (no pause).
This patch fixes following failure during bootup:
mdio@24520:01 not found
eth0: Could not attach to PHY
IP-Config: Failed to open eth0
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
commit b31a1d8b41 ("gianfar: Convert
gianfar to an of_platform_driver") introduced a child node for
the ethernet@25000 controller, but no address and size cells
specifiers were added, and that makes dtc unhappy:
DTC: dts->dtb on file "arch/powerpc/boot/dts/mpc8313erdb.dts"
Warning (reg_format): "reg" property in /soc8313@e0000000/ethernet@25000/mdio@25520 has invalid length (8 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells value for /soc8313@e0000000/ethernet@25000/mdio@25520
Warning (avoid_default_addr_size): Relying on default #size-cells value for /soc8313@e0000000/ethernet@25000/mdio@25520
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
I noticed this doing some randconfig testing (.config below). I have
CONFIG_PM but no CONFIG_SUSPEND. Bug is against mainline.
arch/powerpc/sysdev/built-in.o: In function `ipic_suspend':
ipic.c:(.text+0x6b34): undefined reference to `fsl_deep_sleep'
make[1]: *** [.tmp_vmlinux1] Error 1
make: *** [sub-make] Error 2
Looks like #ifdef CONFIG_PM in arch/powerpc/sysdev/ipic.c should be
CONFIG_SUSPEND. d49747bdfb introduced
this.
Fix build when we have CONFIG_PM but no CONFIG_SUSPEND.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Implement Linus's suggestion: introduce the hpet_cnt_ahead()
helper function to compare hpet time values - like other
wrapping counter comparisons are abstracted away elsewhere.
(jiffies, ktime_t, etc.)
Reported-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
They can't be used for profiling and NMI watchdog currently
since they lack the counter overflow interrupt.
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent kprobes from catching spurious faults which will cause infinite
recursive page-fault and memory corruption by stack overflow.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: <stable@kernel.org> [2.6.28.x]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'sh/for-2.6.29' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Fix up T-bit error handling in SH-4A mutex fastpath.
sh: Fix up spurious syscall restarting.
sh: fcnvds fix with denormalized numbers on SH-4 FPU.
sh: Only reserve memory under CONFIG_ZERO_PAGE_OFFSET when it != 0.
sh: Handle calling csum_partial with misaligned data
sh: ap325rxa: Enable ov772x in defconfig.
sh: ap325rxa: Add ov772x support.
sh: ap325rxa: control camera power toggling.
sh: mach-migor: Enable ov772x and tw9910 in defconfig.
Do usual do {} while (0) dance, otherwise
fs/gfs2/util.c:99: error: expected expression before 'else'
drivers/scsi/lpfc/lpfc_sli.c:363: error: expected expression before 'else'
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At this time, the PowerNow! driver for K8 uses an experimentally
derived formula to calculate transition latency. The value it
provides is orders of magnitude too large on modern systems.
This patch replaces the formula with ACPI _PSS latency values
for more accuracy and better performance.
I've tested it on two 2nd generation Opteron systems, a 3rd
generation Operton system, and a Turion X2 without seeing any
stability problems.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
Due to recurring issues with DMAR support on certain platforms.
There's a number of filesystem corruption incidents reported:
https://bugzilla.redhat.com/show_bug.cgi?id=479996http://bugzilla.kernel.org/show_bug.cgi?id=12578
Provide a Kconfig option to change whether it is enabled by
default.
If disabled, it can still be reenabled by passing intel_iommu=on to the
kernel. Keep the .config option off by default.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-By: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On an x86 system which doesn't support global mappings,
__supported_pte_mask has _PAGE_GLOBAL clear, to make sure it never
appears in the PTE. pfn_pte() and so on will enforce it with:
static inline pte_t pfn_pte(unsigned long page_nr, pgprot_t pgprot)
{
return __pte((((phys_addr_t)page_nr << PAGE_SHIFT) |
pgprot_val(pgprot)) & __supported_pte_mask);
}
However, we overload _PAGE_GLOBAL with _PAGE_PROTNONE on non-present
ptes to distinguish them from swap entries. However, applying
__supported_pte_mask indiscriminately will clear the bit and corrupt the
pte.
I guess the best fix is to only apply __supported_pte_mask to present
ptes. This seems like the right solution to me, as it means we can
completely ignore the issue of overlaps between the present pte bits and
the non-present pte-as-swap entry use of the bits.
__supported_pte_mask contains the set of flags we support on the
current hardware. We also use bits in the pte for things like
logically present ptes with no permissions, and swap entries for
swapped out pages. We should only apply __supported_pte_mask to
present ptes, because otherwise we may destroy other information being
stored in the ptes.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This patch makes the ROM reading code return an error to user space if
the size of the ROM read is equal to 0.
The patch also emits a warnings if the contents of the ROM are invalid,
and documents the effects of the "enable" file on ROM reading.
Signed-off-by: Timothy S. Nelson <wayland@wayland.id.au>
Acked-by: Alex Villacis-Lasso <a_villacis@palosanto.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There's a small problem with hpet_rtc_reinit function - it checks
for the:
hpet_readl(HPET_COUNTER) - hpet_t1_cmp > 0
to continue increasing both the HPET_T1_CMP (register) and the
hpet_t1_cmp (variable).
But since the HPET_COUNTER is always 32-bit, if the hpet_t1_cmp
is 64-bit this condition will always be FALSE once the latter hits
the 32-bit boundary, and we can have a situation, when we don't
increase the HPET_T1_CMP register high enough.
The result - timer stops ticking, since HPET_T1_CMP becomes less,
than the COUNTER and never increased again.
The solution is (based on Linus's suggestion) to not compare 64-bits
(on 64-bit x86), but to do the comparison on 32-bit signed
integers.
Reported-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: APIC: enable workaround on AMD Fam10h CPUs
xen: disable interrupts before saving in percpu
x86: add x86@kernel.org to MAINTAINERS
x86: push old stack address on irqstack for unwinder
irq, x86: fix lock status with numa_migrate_irq_desc
x86: add cache descriptors for Intel Core i7
x86/Voyager: make it build and boot
Impact: cleanup
Some lines exceed the 80 char width making them unreadable.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch echoes what we already do on 32-bit since
90f7d25c6b, and prints the DMI
product name in show_regs, so that system specific problems can be
easily identified.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (40 commits)
Blackfin arch: Remove outdated code
Blackfin arch: Fix udelay implementation
Blackfin arch: Update Copyright information
Blackfin arch: Add BF561 PPI POLS, POLC Masks
Blackfin arch: Update CM-BF527 kernel config
Blackfin arch: define bfin_memmap as static since it is only used here
Blackfin arch: cplb mananger: use a do...while loop rather than a for loop
Blackfin arch: fix bug - traps test case 19 for exception 0x2d fails
Blackfin arch: add platform device bfin_mii-bus and KSZ8893M switch driver platform resources to board files
Blackfin arch: build jtag tty driver as a module by default
Blackfin arch: fix 2 bugs related to debug
Blackfin arch: Add ANOMALY_05000380 to BF54x to kill the compile warning
Blackfin arch: Fix bug - 561 SMP kernel can't boot from jffs2
Blackfin arch: base SIC_IWR# programming on whether the MMR exists
Blackfin arch: read SYSCR on newer parts that mirror the bits of SWRST in it
Blackfin arch: fixup board init function name
Blackfin arch: drop CONFIG_I2C_BOARDINFO ifdefs
Blackfin arch: bfin_reset->_bfin_reset redirection no longer needed
Blackfin arch: sync reboot handler with version in u-boot
Blackfin arch: Faster Implementation of csum_tcpudp_nofold()
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Kill bogus TPC/address truncation during 32-bit faults.
sparc: fixup for sparseirq changes
sparc64: Validate kernel generated fault addresses on sparc64.
sparc64: On non-Niagara, need to touch NMI watchdog in NOHZ mode.
sparc64: Implement NMI watchdog on capable cpus.
sparc: Probe PMU type and record in sparc_pmu_type.
sparc64: Move generic PCR support code to seperate file.
The removed version with the loop registers saved on the stack was
originally intended to workaround the missing toolchain support for
LoopReg Clobbers.
Since our toolchain now supports these there is no point in keeping this
workaround. And since we don't touch LoopRegs anymore we're no longer
subject for ANOMALY_05000312.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Avoid possible overflow during 32*32->32 multiplies.
Reported-by: Marco Reppenhagen <marco.reppenhagen@auerswald.de>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
use a do...while loop rather than a for loop to get slightly better
optimization and to avoid gcc "may be used uninitialized" warnings ...
we know that the [id]cplb_nr_bounds variables will never be 0, so this
is OK
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Enable null pointer checking for ICPLBs. The code was there but for
some reason I had commented it out at some stage during development.
Should restrict this to 1K since atomic ops start there.
Signed-off-by: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
- unable to single step over emuexcpt instruction
- gdbproxy goes into infinite loop when doing gdb does "next" over
"emuexcpt"
Don't decrement PC after software breakpoint.
Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
bss_l2 section is garbage when the data in this section is used by
_bfin_relocate_l1_mem, so move the zero out function ahead.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
base SIC_IWR# programming on whether the MMR exists
rather than having to maintain another list of processors
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Drop CONFIG_I2C_BOARDINFO ifdefs as the common i2c header handles this
already by stubbing things out
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Avoid conditional branch instructions during carry bit additions.
Special thanks to Bernd.
Simplify: Use ((len + proto) << 8) like every other __LITTLE_ENDIAN__ machine
Cc: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
[Mike Frysinger <vapier.adi@gmail.com>:
- setup P_DEFAULT_BOOT_SPI_CS for every arch based on
the default bootrom behavior and convert all our boards
to it
- revert previous anomaly change ... bf51x is not affected
by anomaly 05000353]
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Russell King