napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 712c318534 ("net: thunderx: Program LMAC credits based on MTU")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Transmit queue timeout issue is seen in two cases
- Due to a race condition btw setting stop_queue at xmit()
and checking for stopped_queue in NAPI poll routine, at times
transmission from a SQ comes to a halt. This is fixed
by using barriers and also added a check for SQ free descriptors,
incase SQ is stopped and there are only CQE_RX i.e no CQE_TX.
- Contrary to an assumption, a HW errata where HW doesn't stop transmission
even though there are not enough CQEs available for a CQE_TX is
not fixed in T88 pass 2.x. This results in a Qset error with
'CQ_WR_FULL' stalling transmission. This is fixed by adjusting
RXQ's RED levels for CQ level such that there is always enough
space left for CQE_TXs.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable pause frames on both Rx and Tx side, configure pause
interval e.t.c. Also support for enable/disable pause frames
on Rx/Tx via ethtool has been added.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following
1. When interface is being teardown and queues are being cleaned up,
free pending SKBs that are in SQ which are either not transmitted
or freed as NAPI is disabled by that time.
2. While interface initialization, delay CFG_DONE notification till
the end to avoid corner cases where TXQs are enabled but CQ
interrupts are not which results blocking transmission and kicking
off watchdog.
3. Check for IFF_UP while re-enabling RBDR interrupts from tasklet.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes multiple issues
1. Convert all driver statistics to percpu counters for accuracy.
2. To avoid multiple CQEs posted by a TSO packet appended to HW,
TSO pkt's SQE has 'post_cqe' not set but a dummy SQE is added
for getting HW transmit completion notification. This dummy
SQE has 'dont_send' set and HW drops the pkt pointed to in this
thus Tx drop counter increases. This patch fixes this by subtracting
SW tx tso counter from HW Tx drop counter for actual packet drop counter.
3. Reset all individual queue's and VNIC HW stats when interface is going down.
4. Getrid off unnecessary counters in hot path.
5. Bringout all CQE error stats i.e both Rx and Tx.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Programming LMAC credits taking 9K frame size by default is incorrect
as for an interface which is one of the many on the same BGX/QLM
no of credits available will be less as Tx FIFO will be divided
across all interfaces. So let's say a BGX with 40G interface and another
BGX with multiple 10G, bandwidth of 10G interfaces will be effected when
traffic is running on both 40G and 10G interfaces simultaneously.
This patch fixes this issue by programming credits based on netdev's MTU.
Also fixed configuring MTU to HW and added CQE counter for pkts which
exceed this value.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
On ThunderX 88xx pass 2.x chips when TSO is offloaded to HW,
HW posts a CQE for every TSO segment transmitted. Current code
does handles this, but is prone to issues when segment sizes are
small resulting in SW processing too many CQEs and also at times
frees a SKB which is not yet transmitted.
This patch handles the errata in a different way and eliminates issues
with earlier approach, TSO packet is submitted to HW with post_cqe=0,
so that no CQE is posted upon completion of transmission of TSO packet
but a additional HDR + IMMEDIATE descriptors are added to SQ due to
which a CQE is posted and will have required info to be used while
cleanup in napi. This way only one CQE is posted for a TSO packet.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use standard API to generate a random RSS hash key
on every boot.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables bulk freeing on the Tx side.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set MAC addresses only for primary VF's and don't for
secondary VFs.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding debug messages in case of NACK for a mailbox message, also
did small cleanups.
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the way VF's irqs are visible in /proc/interrupts.
Instead of VF id, logical interface's netdev name is used for IRQ
naming and also all secondary VF's interrupts in multiqset config
use primary VF's netdev name.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
81xx has only 4 CPUs, so it doesn't make sense to initialize
entire Qset i.e 8 queues by default. Made changes to queue
initialization to init queues equal to number of CPUs or
8 queues whichever is lesser. Also this will be applicable to
VMs with VNIC VF attached and having less VCPUs
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds PCI device IDs of VNIC on newer chips and also
registers VF driver with them. Device id remains same for all
versions of chips but subsystem device id changes.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/phy/bcm7xxx.c
drivers/net/phy/marvell.c
drivers/net/vxlan.c
All three conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Counting rx packets for every CQE_RX in CQ irq handler is incorrect.
Synchronization is missing when multiple queues are receiving packets
simultaneously. Like transmit packet stats use HW stats here.
Also removed unused 'cqe_type' parameter in nicvf_rcv_pkt_handler().
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For secondary Qsets 'hw_tso' is not getting set as probe() returns
much earlier. Fixed it by moving silicon revision check.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a interface is assigned morethan 8 queues and the logical interface
is toggled i.e down & up, additional queues or qsets are not initialized
as secondary qset count is being set to zero while tearing down.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This affinity hint can be used by user space irqbalance tool to set
preferred CPU mask for irqs registered by this VF. Irqbalance needs
to be in 'exact' mode to set irq affinity same as indicated by
affinity hint.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_schedule is being called from hard irq context, hence
switch to napi_schedule_irqoff which avoids unneeded call
to local_irq_save and local_irq_restore.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When system is low on atomic memory, too many error messages are logged.
Since this is not a total failure but a simple switch to non-atomic allocation
better to have a stat.
Also add a stat for reset, kicked due to transmit watchdog timeout.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@caviumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for offloading TCP segmentation to HW in pass-2
revision of hardware. Both driver level SW TSO for pass1.x chips
and HW TSO for pass-2 chip will co-exist. Modified SQ descriptor
structures to reflect pass-2 hw implementation.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call netif_carrier_on() only if interface's link is up. Switching this on
upon IFF_UP by default, is causing issues with ethernet channel bonding
in LACP mode. Initial NETDEV_CHANGE notification was being skipped.
Also fixed some issues with link/speed/duplex reporting via ethtool.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases the crash is caused by nicvf_remove() being called from
outside. For example, if we try to feed the device to vfio after the
probe has failed for some reason. So, move the check to better place.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If device probe fails, driver remains bound to the PCI device. However,
driver data has been reset to NULL. This causes crash upon dereferencing
it in nicvf_remove()
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for setting VF's corresponding BGX LMAC in internal
loopback mode. This mode can be used for verifying basic HW
functionality such as packet I/O, RX checksum validation,
CQ/RBDR interrupts, stats e.t.c. Useful when DUT has no external
network connectivity.
'loopback' mode can be enabled or disabled via ethtool.
Note: This feature is not supported when no of VFs enabled are
morethan no of physical interfaces i.e active BGX LMACs
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for handling multiple qsets assigned to a
single VF. There by increasing no of queues from earlier 8 to max
no of CPUs in the system i.e 48 queues on a single node and 96 on
dual node system. User doesn't have option to assign which Qsets/VFs
to be merged. Upon request from VF, PF assigns next free Qsets as
secondary qsets. To maintain current behavior no of queues is kept
to 8 by default which can be increased via ethtool.
If user wants to unbind NICVF driver from a secondary Qset then it
should be done after tearing down primary VF's interface.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework interrupt handler to avoid checking IRQ affinity of
CQ interrupts. Now separate handlers are registered for each IRQ
including RBDR. Register interrupt handlers for only those
which are being used. Add nicvf_dump_intr_status() and use it
in irq handlers.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch configures HW to strip 802.1Q header if found in a
receiving packet. The stripped VLAN ID and TCI information is
passed on to software via CQE_RX. Also sets netdev's 'vlan_features'
so that other HW offload features can be used for tagged packets.
This offload feature can be enabled or disabled via ethtool.
Network stack normally ignores RPS for 802.1Q packets and hence low
throughput. With this offload enabled throughput for tagged packets
will be almost same as normal packets.
Note: This patch doesn't enable HW VLAN insertion for transmit packets.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support for receive hashing HW offload by using RSS_ALG
and RSS_TAG fields of CQE_RX descriptor. Also removed dependency
on minimum receive queue count to configure RSS so that hash is
always generated.
This hash is used by RPS logic to distribute flows across multiple
CPUs. Offload can be disabled via ethtool.
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the nicvf_send_msg_to_pf() function in the mailbox code.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added ethtool support to dump receive packet error statistics reported
in CQE. Also made some small fixes
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a crash when changing rss with multiple traffic flows.
While interface teardown, disable tx queues after all NAPI threads
are done. If done otherwise tx queues might be woken up inside NAPI
if any CQE_TX are processed.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a txq (SQ) remains in stopped state after this timeout its
considered as stuck and interface is reinited.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously TXQ is wakedup whenever napi is executed
and irrespective of if any CQE_TX are processed or not.
Added 'txq_stop' and 'txq_wake' counters to aid in debugging
if there are any future issues.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed 'tso_hdrs' memory not being freed properly.
Also fixed SQ skbuff maintenance issues.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This bug pops up with NetworkManager on Fedora 21. NetworkManager tends to
stop the interface (nicvf_stop() is called) before changing settings. In
stopped state MAC cannot be sent to a PF. However, when the interface is
restarted (nicvf_open() is called), we ping the PF using NIC_MBOX_MSG_READY
message, and the PF replies back with old MAC address, overriding what we
had after MAC setting from userspace. As a result, we cannot set MAC
address using NetworkManager.
This patch introduces special tracking of MAC change in stopped state so
that the correct new MAC address is sent to a PF when interface is reopen.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes sparse messages like this:
drivers/net/ethernet/cavium/thunder/nicvf_main.c:1141:26: sparse: symbol
'nicvf_get_stats64' was not declared. Should it be static?
Also remove unused declarations
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes sparse message:
drivers/net/ethernet/cavium/thunder/nicvf_main.c:385:40: sparse: cast to
restricted __le64
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes sparse message:
drivers/net/ethernet/cavium/thunder/nicvf_main.c:153:25: sparse: cast to
restricted __le64
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet