We are incorrectly rearranging 32-bit words inside a 64-bit typed value
for big endian systems, which would result in never marking a virtual
interrupt as inactive on big endian systems (assuming 32 or fewer LRs on
the hardware). Fix this by not doing any word order manipulation for
the typed values.
Cc: <stable@vger.kernel.org>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
After the timer optimization rework we accidentally end up calling
physical timer enable/disable functions on VHE systems, which is neither
needed nor correct, since the CNTHCTL_EL2 register format is
different when HCR_EL2.E2H is set.
The CNTHCTL_EL2 is initialized when CPUs become online in
kvm_timer_init_vhe() and we don't have to call these functions on VHE
systems, which also allows us to inline the non-VHE functionality.
Reported-by: Jintack Lim <jintack@cs.columbia.edu>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
In order for VLPIs to be delivered to the guest, we must make sure that
the virtual cpuif is always enabled, irrespective of the presence of
virtual interrupt in the LRs.
Acked-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
As we are about to be lazy with saving and restoring the timer
registers, we prepare by moving all possible timer configuration logic
out of the hyp code. All virtual timer registers can be programmed from
EL1 and since the arch timer is always a level triggered interrupt we
can safely do this with interrupts disabled in the host kernel on the
way to the guest without taking vtimer interrupts in the host kernel
(yet).
The downside is that the cntvoff register can only be programmed from
hyp mode, so we jump into hyp mode and back to program it. This is also
safe, because the host kernel doesn't use the virtual timer in the KVM
code. It may add a little performance performance penalty, but only
until following commits where we move this operation to vcpu load/put.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Per ARM DDI 0487B.a, the registers are named ICC_IGRPEN*_EL1 rather than
ICC_GRPEN*_EL1. Correct our mnemonics and comments to match, before we
add more GICv3 register definitions.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: kvmarm@lists.cs.columbia.edu
Acked-by: Christoffer Dall <cdall@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
A write-to-read-only GICv3 access should UNDEF at EL1. But since
we're in complete paranoia-land with broken CPUs, let's assume the
worse and gracefully handle the case.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
A read-from-write-only GICv3 access should UNDEF at EL1. But since
we're in complete paranoia-land with broken CPUs, let's assume the
worse and gracefully handle the case.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Add a handler for reading/writing the guest's view of the ICC_PMR_EL1
register, which is located in the ICH_VMCR_EL2.VPMR field.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Add a handler for reading/writing the guest's view of the ICV_CTLR_EL1
register. only EOIMode and CBPR are of interest here, as all the other
bits directly come from ICH_VTR_EL2 and are Read-Only.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Add a handler for reading the guest's view of the ICV_RPR_EL1
register, returning the highest active priority.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Add a handler for writing the guest's view of the ICC_DIR_EL1
register, performing the deactivation of an interrupt if EOImode
is set ot 1.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
A number of Group-0 registers can be handled by the same accessors
as that of Group-1, so let's add the required system register encodings
and catch them in the dispatching function.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Add a handler for reading/writing the guest's view of the ICC_IGRPEN0_EL1
register, which is located in the ICH_VMCR_EL2.VENG0 field.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Add a handler for reading/writing the guest's view of the ICC_BPR0_EL1
register, which is located in the ICH_VMCR_EL2.BPR0 field.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
In order to be able to trap Group-1 GICv3 system registers, we need to
set ICH_HCR_EL2.TALL1 before entering the guest. This is conditionally
done after having restored the guest's state, and cleared on exit.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Add a handler for reading the guest's view of the ICV_HPPIR1_EL1
register. This is a simple parsing of the available LRs, extracting the
highest available interrupt.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Add a handler for reading/writing the guest's view of the ICV_AP1Rn_EL1
registers. We just map them to the corresponding ICH_AP1Rn_EL2 registers.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Add a handler for writing the guest's view of the ICC_EOIR1_EL1
register. This involves dropping the priority of the interrupt,
and deactivating it if required (EOImode == 0).
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Add a handler for reading the guest's view of the ICC_IAR1_EL1
register. This involves finding the highest priority Group-1
interrupt, checking against both PMR and the active group
priority, activating the interrupt and setting the group
priority as active.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Add a handler for reading/writing the guest's view of the ICC_IGRPEN1_EL1
register, which is located in the ICH_VMCR_EL2.VENG1 field.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Add a handler for reading/writing the guest's view of the ICC_BPR1_EL1
register, which is located in the ICH_VMCR_EL2.BPR1 field.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
In order to start handling guest access to GICv3 system registers,
let's add a hook that will get called when we trap a system register
access. This is gated by a new static key (vgic_v3_cpuif_trap).
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
As we're about to access the Active Priority registers a lot more,
let's define accessors that take the register number as a parameter.
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
We used to extract PRIbits from the ICH_VT_EL2 which was the upper field
in the register word, so a mask wasn't necessary, but as we switched to
looking at PREbits, which is bits 26 through 28 with the PRIbits field
being potentially non-zero, we really need to mask off the field value,
otherwise fun things may happen.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
The GICv3 documentation is extremely confusing, as it talks about
the number of priorities represented by the ICH_APxRn_EL2 registers,
while it should really talk about the number of preemption levels.
This leads to a bug where we may access undefined ICH_APxRn_EL2
registers, since PREbits is allowed to be smaller than PRIbits.
Thankfully, nobody seem to have taken this path so far...
The fix is to use ICH_VTR_EL2.PREbits instead.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
When iterating over the used LRs, be careful not to try to access
an unused LR, or even an unimplemented one if you're unlucky...
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
When emulating a GICv2-on-GICv3, special care must be taken to only
save/restore VMCR_EL2 when ICC_SRE_EL1.SRE is cleared. Otherwise,
all Group-0 interrupts end-up being delivered as FIQ, which is
probably not what the guest expects, as demonstrated here with
an unhappy EFI:
FIQ Exception at 0x000000013BD21CC4
This means that we cannot perform the load/put trick when dealing
with VMCR_EL2 (because the host has SRE set), and we have to deal
with it in the world-switch.
Fortunately, this is not the most common case (modern guests should
be able to deal with GICv3 directly), and the performance is not worse
than what it was before the VMCR optimization.
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
We don't use these fields anymore so let's nuke them completely.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Now when we don't look at the MISR and EISR values anymore, we can get
rid of the logic to save them in the GIC save/restore code.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
There is no need to calculate and maintain live_lrs when we always
populate the lowest numbered LRs first on every entry and clear all LRs
on every exit.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
We don't have to save/restore the VMCR on every entry to/from the guest,
since on GICv2 we can access the control interface from EL1 and on VHE
systems with GICv3 we can access the control interface from KVM running
in EL2.
GICv3 systems without VHE becomes the rare case, which has to
save/restore the register on each round trip.
Note that userspace accesses may see out-of-date values if the VCPU is
running while accessing the VGIC state via the KVM device API, but this
is already the case and it is up to userspace to quiesce the CPUs before
reading the CPU registers from the GIC for an up-to-date view.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@cs.columbia.edu>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Make cntvoff per each timer context. This is helpful to abstract kvm
timer functions to work with timer context without considering timer
types (e.g. physical timer or virtual timer).
This also would pave the way for ever doing adjustments of the cntvoff
on a per-CPU basis if that should ever make sense.
Signed-off-by: Jintack Lim <jintack@cs.columbia.edu>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Abstract virtual timer context into a separate structure and change all
callers referring to timer registers, irq state and so on. No change in
functionality.
This is about to become very handy when adding the EL1 physical timer.
Signed-off-by: Jintack Lim <jintack@cs.columbia.edu>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Current KVM world switch code is unintentionally setting wrong bits to
CNTHCTL_EL2 when E2H == 1, which may allow guest OS to access physical
timer. Bit positions of CNTHCTL_EL2 are changing depending on
HCR_EL2.E2H bit. EL1PCEN and EL1PCTEN are 1st and 0th bits when E2H is
not set, but they are 11th and 10th bits respectively when E2H is set.
In fact, on VHE we only need to set those bits once, not for every world
switch. This is because the host kernel runs in EL2 with HCR_EL2.TGE ==
1, which makes those bits have no effect for the host kernel execution.
So we just set those bits once for guests, and that's it.
Signed-off-by: Jintack Lim <jintack@cs.columbia.edu>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
So we can reuse the code under arch/arm
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
If, when proxying a GICV access at EL2, we detect that the guest is
doing something silly, report an EL1 SError instead ofgnoring the
access.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Now that we have the necessary infrastructure to handle MMIO accesses
in HYP, perform the GICV access on behalf of the guest. This requires
checking that the access is strictly 32bit, properly aligned, and
falls within the expected range.
When all condition are satisfied, we perform the access and tell
the rest of the HYP code that the instruction has been correctly
emulated.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
In order to efficiently perform the GICV access on behalf of the
guest, we need to be able to avoid going back all the way to
the host kernel.
For this, we introduce a new hook in the world switch code,
conveniently placed just after populating the fault info.
At that point, we only have saved/restored the GP registers,
and we can quickly perform all the required checks (data abort,
translation fault, valid faulting syndrome, not an external
abort, not a PTW).
Coming back from the emulation code, we need to skip the emulated
instruction. This involves an additional bit of save/restore in
order to be able to access the guest's PC (and possibly CPSR if
this is a 32bit guest).
At this stage, no emulation code is provided.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
I don't think any single piece of the KVM/ARM code ever generated
as much hatred as the GIC emulation.
It was written by someone who had zero experience in modeling
hardware (me), was riddled with design flaws, should have been
scrapped and rewritten from scratch long before having a remote
chance of reaching mainline, and yet we supported it for a good
three years. No need to mention the names of those who suffered,
the git log is singing their praises.
Thankfully, we now have a much more maintainable implementation,
and we can safely put the grumpy old GIC to rest.
Fellow hackers, please raise your glass in memory of the GIC:
The GIC is dead, long live the GIC!
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
When saving the state of the list registers, it is critical to
reset them zero, as we could otherwise leave unexpected EOI
interrupts pending for virtual level interrupts.
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Now that the new VGIC implementation has reached feature parity with
the old one, add the new files to the build system and add a Kconfig
option to switch between the two versions.
We set the default to the new version to get maximum test coverage,
in case people experience problems they can switch back to the old
behaviour if needed.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
The number of list registers is a property of the underlying system, not
of emulated VGIC CPU interface.
As we are about to move this variable to global state in the new vgic
for clarity, move it from the legacy implementation as well to make the
merge of the new code easier.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
We are about to modify the VGIC to allocate all data structures
dynamically and store mapped IRQ information on a per-IRQ struct, which
is indeed allocated dynamically at init time.
Therefore, we cannot record the mapped IRQ info from the timer at timer
reset time like it's done now, because VCPU reset happens before timer
init.
A possible later time to do this is on the first run of a per VCPU, it
just requires us to move the enable state to be a per-VCPU state and do
the lookup of the physical IRQ number when we are about to run the VCPU.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
So far, we're always writing all possible LRs, setting the empty
ones with a zero value. This is obvious doing a lot of work for
nothing, and we're better off clearing those we've actually
dirtied on the exit path (it is very rare to inject more than one
interrupt at a time anyway).
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On exit, any empty LR will be signaled in GICH_ELRSR*. Which
means that we do not have to save it, and we can just clear
its state in the in-memory copy.
Take this opportunity to move the LR saving code into its
own function.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In order to make the saving path slightly more readable and
prepare for some more optimizations, let's move the GICH_ELRSR
saving to its own function.
No functional change.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Next on our list of useless accesses is the maintenance interrupt
status registers (GICH_MISR, GICH_EISR{0,1}).
It is pointless to save them if we haven't asked for a maintenance
interrupt the first place, which can only happen for two reasons:
- Underflow: GICH_HCR_UIE will be set,
- EOI: GICH_LR_EOI will be set.
These conditions can be checked on the in-memory copies of the regs.
Should any of these two condition be valid, we must read GICH_MISR.
We can then check for GICH_MISR_EOI, and only when set read
GICH_EISR*.
This means that in most case, we don't have to save them at all.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
GICv2 registers are *slow*. As in "terrifyingly slow". Which is bad.
But we're equaly bad, as we make a point in accessing them even if
we don't have any interrupt in flight.
A good solution is to first find out if we have anything useful to
write into the GIC, and if we don't, to simply not do it. This
involves tracking which LRs actually have something valid there.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We already have virt/kvm/arm/ containing timer and vgic stuff.
Add yet another subdirectory to contain the hyp-specific files
(timer and vgic again).
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Christoffer Dall