When TSSI calibration is disabled (which it means the device has been
equipped with an external power amplifier) we need to refer to
different eeprom fields in order to properly configure tx power
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Set per-channel target power as the minimum between the regulatory
tx power and the value configured in the eeprom
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move conn_type configuration directly in mt7615_mcu_set_sta_rec and
remove sta_rec_convert_vif_type since it is actually used just in
mt7615_mcu_set_sta_rec
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Now that tx status reporting can figure out the first attempted rate, we can
make switching from lower rates to higher rates more conservative.
This reduces retries under bad link conditions and ensures that fallback
rates get more test coverage
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Tx status reporting on mt7603 has a number of issues:
- the hardware can alter the first rate index, but it is not reported to
the driver
- probing is very imprecise, because it alters the per-client rate set,
but only considers info->status.rates for rate selection of a single probe
packet
- short/long GI selection has limitations, which are not accurately reported
to mac80211
- if rates are changed while packets are in flight, tx status reports for
the old rate set might be processed based on the new selection
This led to very suboptimal rate selection with minstrel_ht.
This patch completely reworks tx status reporting to get rid of these
limitations:
- Store the previous and current rate set in the driver + the TSF value
at the time of the switch.
- Use the tx status TSF value to determine which rate set needs to be used
as reference.
- Report only short or long GI rates for a single status event, not a mix.
- The hardware reports the last used rate index. Use it along with the
retry count to figure out what rate was used for the first attempt.
- Use the same retry count value for all rate slots to make this calculation
work.
- Derive the probe rate from the current rateset instead of the skb cb
- Do not wait for a status report for the probe frame before removing the
probe rate from the rate table. Do it immediately after it was referenced
in a tx status report.
- Use the first half of the first rate retry budget for the probe rate
in order to avoid using too many retries on that rate
With this patch, throughput under bad link conditions is improved
significantly, and there is a lot less rate fluctuation going on.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When loading EEPROM data from flash, the RF frontend settings need to be
initialized from flash data. Without this, the chip loads the wrong values
from its internal eFuse ROM.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not check key pointer in mt7615_mcu_set_wtbl_key since if set_key_cmd
is SET_KEY, key will be always not NULL. This patch will address a false
positive reported by Coverity-Scan
Addresses-Coverity-ID: 1445463 ("Dereference after null check")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove tim_len in mt7615_mcu_set_bcn since it is not actually used
and ieee80211_beacon_get_tim checks if tim_length is NULL
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix wrong WCID assignment and add RKV (RX Key of this entry is valid)
flag to check if peer uses the same configuration with previous
handshaking.
If the configuration is mismatch, WTBL indicates a “cipher mismatch”
to stop SEC decryption to prevent the packet from damage.
Suggested-by: YF Luo <yf.luo@mediatek.com>
Suggested-by: Yiwei Chung <yiwei.chung@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fixes gcc '-Wunused-but-set-variable' warnings:
drivers/net/wireless/mediatek/mt76/mt7603/mac.c: In function mt7603_fill_txs:
drivers/net/wireless/mediatek/mt76/mt7603/mac.c:969:5: warning: variable pid set but not used [-Wunused-but-set-variable]
drivers/net/wireless/mediatek/mt76/mt7603/mac.c:961:7: warning: variable final_mpdu set but not used [-Wunused-but-set-variable]
drivers/net/wireless/mediatek/mt76/mt7615/mac.c: In function mt7615_fill_txs:
drivers/net/wireless/mediatek/mt76/mt7615/mac.c:555:5: warning: variable pid set but not used [-Wunused-but-set-variable]
drivers/net/wireless/mediatek/mt76/mt7615/mac.c:552:19: warning: variable final_mpdu set but not used [-Wunused-but-set-variable]
They are never used, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt7603_get_rate in mac80211.c and rename it to mt76_get_rate
since it is shared between mt7603 and mt7615 drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since all the routines in mt7615_config grub mt76.mutex moves
mutex_lock/mutex_unlock at the beginning/end of mt7615_config
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Initialize get_txpower mac80211 callback to mt76_get_txpower
in order to report the configured tx power to mac80211
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_mcu_set_tx_power routine in order to cap tx power
according to the value configured by the user
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Genralize mt76_get_txpower routine for 4x4:4 capable devices
in order to be reused in mt7615 driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Select supported band according to the value read from
eeprom mtd/otp partition
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Calibration data are often available on a specific mtd partition on
embedded devices. Take into account eeprom calibration data if
available.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt7615_insert_ccmp_hdr in mac80211.c and rename it in
mt76_insert_ccmp_hdr since it is shared between mt7603 and mt7615
drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
To avoid aggregating rate control probing packets with other traffic, and to
ensure that the probing rate gets used, probing packets get assigned a different
internal queueing priority.
This causes packets to be transmitted in a different order, which is compensated
by the receiver side reordering.
However, if A-MPDU is disabled, this reordering can become visible to upper
layers on the receiver side. Disable the priority change if A-MPDU is disabled.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When the hardware falls back to lower rates for a transmit attempt, only the
first status report will show the number of retries correctly. The frames
that follow will report the correct final rate, but number of retries set to 0.
This can cause the rate control module to vastly underestimate the number of
retransmissions per rate.
To fix this, we need to keep track of the initial requested tx rate per packet
and pass it to the status information.
For frames with tx status requested, this is simple: use the rate configured
in info->control.rates[0] as reference.
For no-skb tx status information, we have to encode the requested tx rate in
the packet id (and make it possible to distinguish it from real packet ids).
To do that, reduce the packet id field size by one bit, and use that bit to
indicate packet id vs rate.
This change also improves reporting by filling the status rate array with
rates from first rate to final rate, taking the same steps as the hardware
fallback table. This matters in corner cases like MCS8 on HT, where the
fallback target is MCS0, not MCS7.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
First set of patches for 5.3, but not that many patches this time.
This pull request fails to compile with the tip tree due to
ktime_get_boot_ns() API changes there. It should be easy for Linus to
fix it in p54 driver once he pulls this, an example resolution here:
https://lkml.kernel.org/r/20190625160432.533aa140@canb.auug.org.au
Major changes:
airo
* switch to use skcipher interface
p54
* support boottime in scan results
rtw88
* add fast xmit support
* add random mac address on scan support
rt2x00
* add software watchdog to detect hangs, it's disabled by default
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdE5OGAAoJEG4XJFUm622bWCoH/1bLdkTYOkSatXxpHn2cVRvA
SrQ+ZSfOWJe5d0B+9HWhO5r+Savuu+IrgcC6vSIBBVglF5Tf6F0DAxHVrIwc9MSY
QUv4f1suqeH0ipUEBWJXoDXM2OEShvw5WCuY0ZnYw2hZRI7Sb5nqwJEUH57BtBCX
tFW22Ax3ZFTmCfexFgiwEjmtEx6HHz/nleYLMt9gg7X1Twug+QmhEsNw/27PfvMx
RyVyCJ1UvW2x4GHqDRlGxQoh7FlMvuVe/v/VcjGp2Fp8s7GS0xUyA11svGBFpdnT
K94Y3LOcTSdBQwScbn6O2v6EybB9PZYhg6rckwbMgIN2pkkWqXnh5avru4U0T9k=
=yq6Q
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-06-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valu says:
====================
wireless-drivers-next patches for 5.3
First set of patches for 5.3, but not that many patches this time.
This pull request fails to compile with the tip tree due to
ktime_get_boot_ns() API changes there. It should be easy for Linus to
fix it in p54 driver once he pulls this, an example resolution here:
https://lkml.kernel.org/r/20190625160432.533aa140@canb.auug.org.au
Major changes:
airo
* switch to use skcipher interface
p54
* support boottime in scan results
rtw88
* add fast xmit support
* add random mac address on scan support
rt2x00
* add software watchdog to detect hangs, it's disabled by default
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ec8f24b7fa ("treewide: Add SPDX license identifier -
Makefile/Kconfig") marked various Makefiles and Kconfig files within ath
directories as GPL-2.0. But these modules and drivers are actually ISC:
* ath
* ar5523
* ath10k
* ath5k
* ath6kl
* ath9k
* wcn36xx
* wil6210
Fix SPDX tags accordingly.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Integrated WiFi chipset ex:WCN399x supports fw logging
using WMI copy engine and shared mem DIAG based fw logging.
By default shared mem DIAG based fw logging is enabled.
To support WMI copy engine based fw logging add QMI
control message to enable WMI copy engine based fw logging.
Enable WMI based fw logging using fw_diag_log module parameter.
insmod ath10k_core.ko fw_diag_log=1
DIAG utility(https://github.com/andersson/diag) implements extraction
of diagnostics related messages between application processor and
various subsystems while shared mem DIAG based fw logging is enabled.
Testing: Tested on WCN3990/QCA6174 HW
Tested FW: WLAN.HL.3.1-00959-QCAHLSWMTPLZ-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware will report flag with HTT_RX_IND_MPDU_STATUS_TKIP_MIC_ERR
if MIC error, the flag will be used in mac80211.
ieee80211_rx_h_michael_mic_verify will check the flag and start TKIP
countermeasures.
Now countermeasure tests pass both with WPA only and WPA2/WPA mixed
mode.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch will add the support to control the transmit power for traffic
to a station associated with the AP.
Underlying firmware will enforce that the maximum tx power will be based
on the regulatory requirements. If the user given transmit power is greater
than the allowed tx power in the given channel, then the firmware will use
the maximum tx power in the same channel.
Max and Min tx power values will depends on no of tx chain masks,
for QCA9984 allowed tx power range values from 6 to 23.
When 0 is sent to the firmware as tx power, it will revert to the default
tx power for the station.
Tested Hardware : QCA9984
Tested Firmware : 10.4-3.9.0.2-00046
Co-developed-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Ashok Raj Nagarajan <arnagara@codeaurora.org>
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Peer creation in firmware fails if last peer deletion is still
in progress.
The firmware sends a peer delete response event if it advertises
the service WMI_SERVICE_SYNC_DELETE_CMDS. This peer delete response
event is used to synchronize the peer deletion.
Add peer delete response event and wait for the event after
deleting every peer from host driver to synchronize with firmware.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Dundi Raviteja <dundi@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When we add an interface immediately after removing
the interface the vdev deletion in firmware might not
have been completed. We need to synchronize the vdev creation
with the firmware.
Wait for vdev delete response from firmware when we
remove an interface.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Observed PCIE device wake up failed after ~120 iterations of
soft-reboot test. The error message is
"ath10k_pci 0000:01:00.0: failed to wake up device : -110"
The call trace as below:
ath10k_pci_probe -> ath10k_pci_force_wake -> ath10k_pci_wake_wait ->
ath10k_pci_is_awake
Once trigger the device to wake up, we will continuously check the RTC
state until it returns RTC_STATE_V_ON or timeout.
But for QCA99x0 chips, we use wrong value for RTC_STATE_V_ON.
Occasionally, we get 0x7 on the fist read, we thought as a failure
case, but actually is the right value, also verified with the spec.
So fix the issue by changing RTC_STATE_V_ON from 0x5 to 0x7, passed
~2000 iterations.
Tested HW: QCA9984
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, below fixed rate commands are broken,
iw wlanx set bitrates legacy-<2.4|5> ht-mcs-<2.4|5> vht-mcs-<2.4|5> \
<NSS:MCSx>
iw wlanx set bitrates legacy-<2.4|5> <legacy rate> ht-mcs-<2.4|5> \
vht-mcs-<2.4|5> <NSS:MCSx>
There are two methods to set fixed rate, both failed,
- Use vdev fixed rate command
This command only support one single rate, but it's broken due to
mac80211 change commit e8e4f5280d ("mac80211: reject/clear user
rate mask if not usable"), which requires user to specify at least
one legacy rate. So we can't use this command to set ht/vht single
rate any more.
- Use peer_assoc command
This command can update rx capability for multiple rates, it will
work fine for ht mcs rates, as each supported mcs can be advertised
in ht_mcs index mask. But this will not work with vht rates because,
as per the vht mcs capability advertisement, there are only two bits
to indicate the supported mcs. E.g. only support 0-7, 0-8, 0-9.
So introduced new WMI command: WMI_PEER_PARAM_FIXED_RATE. After peer
assoc, the peer fixed rate cmd will work for that specific peer.
Remaining peers will use auto rate. If both vdev fixed rate and peer
fixed rates are given, peer fixed rate will take effect to peers for
which this cmd is given. Remaining peers in that vdev, will use vdev
fixed rate.
Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00035
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The "WARNING" string confuses syzbot, which thinks it found
a crash [1].
Change the string to avoid such problem.
[1] https://lkml.org/lkml/2019/5/9/243
Reported-by: syzbot+c1b25598aa60dcd47e78@syzkaller.appspotmail.com
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In function ath10k_sdio_mbox_rx_alloc() [sdio.c],
ath10k_sdio_mbox_alloc_rx_pkt() is called without handling the error cases.
This will make the driver think the allocation for skb is successful and
try to access the skb. If we enable failslab, system will easily crash with
NULL pointer dereferencing.
Call trace of CONFIG_FAILSLAB:
ath10k_sdio_irq_handler+0x570/0xa88 [ath10k_sdio]
process_sdio_pending_irqs+0x4c/0x174
sdio_run_irqs+0x3c/0x64
sdio_irq_work+0x1c/0x28
Fixes: d96db25d20 ("ath10k: add initial SDIO support")
Signed-off-by: Claire Chang <tientzu@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For QCA988X target, pktlog gives details of the tx bitrate
which is used in the driver for station info.
Enabling pktlog by default will cause more interrupts
in target to host CE pipe, which can impact more CPU usage
for targets ex:WCN3990 and also not required for all other
platforms (eg: WCN3990), for getting tx bitrate.
Enable pktlog only for QCA988X based on hardware params.
Tested HW : WCN3990
Tested FW : WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: e8123bb74c ("ath10k: add per peer tx stats support for 10.2.4")
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Lockdep warns at lockdep_assert_held(&ar->data_lock) in
ath10k_htt_rx_pn_check_replay_hl(). Acquire ar->data_lock before calling
ath10k_htt_rx_pn_check_replay_hl() to fix it.
Call trace:
ath10k_htt_rx_pn_check_replay_hl+0x118/0x134 [ath10k_core]
ath10k_htt_rx_proc_rx_ind_hl+0xd8/0x250 [ath10k_core]
ath10k_htt_t2h_msg_handler+0x148/0xf30 [ath10k_core]
ath10k_htt_htc_t2h_msg_handler+0x24/0x40 [ath10k_core]
ath10k_sdio_irq_handler+0x374/0xaa4 [ath10k_sdio]
Fixes: 130c774957 ("ath10k: add PN replay protection for high latency devices")
Signed-off-by: Claire Chang <tientzu@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware name for UTF mode of SDIO has changed from utf-2.bin to
utf-sdio-2.bin, so it need to change in ath10k, otherwise it will
fail for UTF mode.
After change the name in ath10k, it will success for UTF mode of
SDIO/USB.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The command to simulate firmware crash:
echo soft > /sys/kernel/debug/ieee80211/phy0/ath10k/simulate_fw_crash
It will send WMI_FORCE_FW_HANG_ASSERT to firmware, then it will trigger
CPU interrupt status register for SDIO chip, ath10k driver need to
configure it while enable SDIO interrupt, otherwise ath10k driver will
not get the assert error info.
After this change, it will success for simulate firmware crash.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Tested-by: Claire Chang <tientzu@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k_dbg() is called in ath10k_process_rx() with huge set of arguments
which is causing CPU overhead even when debug_mask is not set.
Good improvement was observed in the receive side performance when call
to ath10k_dbg() is avoided in the RX path.
Since currently all debug messages are sent via tracing infrastructure,
we cannot entirely avoid calling ath10k_dbg. Therefore, call to
ath10k_dbg() is made conditional based on tracing config in the driver.
Trasmit performance remains unchanged with this patch; below are some
experimental results with this patch and tracing disabled.
mesh mode:
w/o this patch with this patch
Traffic TP CPU Usage TP CPU usage
TCP 840Mbps 76.53% 960Mbps 78.14%
UDP 1030Mbps 74.58% 1132Mbps 74.31%
Infra mode:
w/o this patch with this patch
Traffic TP CPU Usage TP CPU usage
TCP Rx 1241Mbps 80.89% 1270Mbps 73.50%
UDP Rx 1433Mbps 81.77% 1472Mbps 72.80%
Tested platform : IPQ8064
hardware used : QCA9984
firmware ver : ver 10.4-3.5.3-00057
Signed-off-by: Kan Yan <kyan@chromium.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Without this op, it will not be possible to configure aggregation for
high latency devices.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is done in order to make the *htt_h2t_aggr_cfg_msg* op align better
with the rest of the htt ops (whom all have inline wrappers).
It also adds support for the case when the op is missing (function
pointer is NULL).
As a result of this, the name of the 32 bit implementation in htt_tx.c
was changed and the function was made static.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use 0600 as edcca file permission in mt76x02 debugfs
Fixes: 643749d4a8 ("mt76: mt76x02: disable ED/CCA by default")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce a knob in mt7603 debugfs in order to enable/disable
energy detection based on CCA thresholds
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Run mt76x02_edcca_init atomically in mt76_edcca_set since it runs
concurrently with calibration work and mt76x2_set_channel.
Moreover perform phy calibration atomically
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to run mt76x02_edcca_init atomically
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76x02_edcca_init in mt76x2u_set_channel since it is already
run by mt76x2u_phy_channel_calibrate performing channel calibration
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove enable parameter from mt76x02_edcca_init routine signature since
it is always true
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Make mt7615_rx_poll_complete static since it is used just in pci.c
to initialize rx_poll_complete function pointer
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Run __mt76_mcu_send_msg instead of __mt7615_mcu_msg_send and remove
duplicated code.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use common function wrapper in mt7615_mcu_exit since the code is shared
with m7603 driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use __mt76_mcu_send_msg wrapper instead of mt7615_mcu_msg_send.
This is a preliminary patch for mt7615-mt7603 mcu code unification
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76 common signature for mt7615_mcu_msg_send. Move skb allocation
in mt7615_mcu_msg_send and remove duplicated code. Remove
__mt7615_mcu_set_wtbl and __mt7615_mcu_set_sta_rec since now are used
just to send mcu msgs. This is a preliminary patch for mt7615-mt7603 mcu
code unification
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove following struct no longer used:
- dev_info
- bss_info
- bss_info_tag_handler
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove function pointers in mt7615_mcu_set_bss_info and run function
directly. Moreover remove __mt7615_mcu_set_bss_info since it is run just
by mt7615_mcu_set_bss_info and remove duplicated istructions
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Unify mt7615_mcu_set_dev_info and __mt7615_mcu_set_dev_info since the
latter is run just by mt7615_mcu_set_dev_info
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove skb_ret parameter from mt7615_mcu_msg_send signature since it is
actually used just by mt7615_mcu_patch_sem_ctrl. This is a prelimanry
patch to use mt76 common mcu API
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove dest parameter from mt7615_mcu_msg_send/__mt7615_mcu_msg_send
routine signature since it can is always set to MCU_S2D_H2N
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove query parameter from mt7615_mcu_msg_send routine signature since
it can be obtained from cmd value
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove unused vif parameter in mt7615_mcu_del_wtbl signature
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use proper mcu message size in mt7615_mcu_add_wtbl and do not
allocate a huge buffer. Moreover use stack memory instead of heap one
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use proper mcu message size in mt7615_mcu_add_wtbl_bmc and do not
allocate a huge buffer. Moreover use stack memory instead of heap one
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove bss_info_convert_vif_type routine since it is run just in
mt7615_mcu_set_bss_info and the switch over vif->type is already there.
Simplify mt7615_mcu_set_bss_info routine
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not loop over cmd payload in __mt7615_mcu_set_sta_rec since it is
already done in before running __mt7615_mcu_set_sta_rec (e.g.
mt7615_mcu_set_sta_rec)
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not loop over cmd payload in __mt7615_mcu_set_wtbl since it is
already done in before running __mt7615_mcu_set_wtbl (e.g.
mt7615_mcu_set_wtbl_key)
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix sparse warning:
drivers/net/wireless/mediatek/mt76/mt7615/pci.c:37:13:
warning: symbol 'mt7615_irq_handler' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We dereference "skb" when we assign:
req.pkt_len = cpu_to_le16(MT_TXD_SIZE + skb->len);
^^^^^^^^
So this patch just moves the dev_kfree_skb() down a bit to avoid the
use after free.
Fixes: 04b8e65922 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The problem is that "mvif->omac_idx" is a u8 so it can't be negative
and the error handling won't work. The get_omac_idx() function returns
-1 on error.
Fixes: 04b8e65922 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move netif_napi_del in mt76_dma_cleanup routine since it is done
by all drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This allows tx scheduling and tx cleanup to run concurrently
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This allows tx scheduling and tx cleanup to run concurrently
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move tx_napi in mt76_dev data structure in order to implement
concurrency between tx scheduling and tx cleanup in mt7603 and mt7615
drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove useless return statment in mt76x02_resync_beacon_timer routine
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The AIRO driver applies a ctr(aes) on a buffer of considerable size
(2400 bytes), and instead of invoking the crypto API to handle this
in its entirety, it open codes the counter manipulation and invokes
the AES block cipher directly.
Let's fix this, by switching to the sync skcipher API instead.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make watchdog disabled by default and add module parameter to enable it.
User will have to create file in /etc/modprobe.d/ with
options rt2800lib watchdog=1
to enable the watchdog or load "rt2800lib watchdog=1" module manually
before loading rt2800{soc,pci,usb} module.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add ieee80211_restart_hw() to watchdog and debugfs file for testing
if restart works as expected.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If we restart hw we should keep existing IV (initialization vector)
otherwise HW encryption will be broken after restart.
Also fix some coding style issues on the way.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add routine to cleanup interfaces data before hw reset as
ieee80211_restart_hw() will do setup interfaces again.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add watchdog for rt2800 devices. For now it only detect hung
and print error.
[Note: I verified that printing messages from process context is
fine on MT7620 (WT3020) platform that have problem when printk
is called from interrupt context].
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For mmio we do not properlly trace dma done Q_INDEX_DMA_DONE index
for TX queues. That would require implementing INT_SOURCE_CSR_*_DMA_DONE
interrupts, what is rather not worth to do due to adding extra
CPU load (small but still somewhat not necessary otherwise).
We can just read TX DMA done indexes from registers directly. What
will be used by watchdog.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Allow subdriver to change watchdog interval by intialize
link->watchdog_interval value before rt2x00link_register().
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch removes the error branch for (queue > dev->queues).
It is no longer needed anymore as the "queue" value is validated by
cfg80211's parse_txq_params() before the driver code gets called.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rtw_writ16_set should be rtw_write16_set
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The hardware default uses management queue to transmit frames that are
downloaded into reserved page, so we need to clearly assign the frames
to use qsel in TX_DESC_QSEL_MGMT to avoid using wrong queue.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
DACK is done right after the hardware has been turned on, which
means it will be done every time we leave the IDLE state.
But it takes ~2 seconds to finish DACK.
We can back up the results and restore them. And it only takes a few
milliseconds to restore the results to the hardware, saving a lot of
time.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We could fail to power on because it was already on. If the return
value is -EALREADY, power off and then power on again to turn on the
hardware as expected.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
8822c used to count OFDM FA count by subtracting tx count from FA count.
But it need to substract more counters to be accurate.
However, we can count it by adding up all of the FA counters we want.
And it is simpler to add than list all of the components to substract.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver Could fail to reset counter if rx clock gating is not disabled.
So we need to disable rx clock gating before resetting counters.
Otherwise counters may increase unexpected.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In 2G channels, the cck source and rxagc should be set to different
values based on different bandwidth to increase the performance of rx
sensitivity.
To improve rx throughput performance, the values of sbd subtune and
pt_opt should be changed in different bandwidth.
Signed-off-by: Chien-Hsun Liao <ben.liao@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Collision of writing rf registers could occur if the driver writes
rf registers by direct write while the hardware is writing other rf
registers by pi write simultaneously.
Hardware pi write can be triggered by rf calibrations sometimes, so
the driver can not always write rf registers by direct write
protection. Direct write protection can make sure that there is no
hardware pi write during the direct write.
According to some experiments, if we add direct write protection
when switching channel, the performance of rf calibration will not
be affected.
Signed-off-by: Chien-Hsun Liao <ben.liao@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add beacon function setting routines for each hardware port.
If beacon function is not enabled, the hardware is not able
to synchronize with AP's beacon and can miss the beacons
under some scenarios such as PS mode.
For AP and Adhoc modes that require to send beacons, do not
update the TSF, otherwise the beacon interval may be affected.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When driver uses random mac address to scan, the unicast probe response
will not be received because the addr1 is not matched. Configure port
address by requested mac address to receive probe response from AP.
To support random mac scan, we need to configure the mac address during
scan period to receive unicast prop_resp. After scan is completed,
configure the mac address back to the original one that the port used.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With dynamic power save support, rtw88 is able to support fast tx
path, claim it to mac80211.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, there is no need to ever check the
return value. This driver was saving the debugfs file away to be
removed at a later time. However, the 80211 core would delete the whole
directory that the debugfs files are created in, after it asks the
driver to do the deletion, so just rely on the 80211 core to do all of
the cleanup for us, making us not need to keep a pointer to the dentries
around at all.
This cleans up the structure of the driver data a bit and makes the code
a tiny bit smaller.
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, there is no need to ever check the
return value. This driver was saving the debugfs file away to be
removed at a later time. However, the 80211 core would delete the whole
directory that the debugfs files are created in, after it asks the
driver to do the deletion, so just rely on the 80211 core to do all of
the cleanup for us, making us not need to keep a pointer to the dentries
around at all.
This cleans up the structure of the driver data a bit and makes the code
a tiny bit smaller.
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variable rtstatus is being initialized with a value that is never read
as rtstatus is being re-assigned a little later on. The assignment is
redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct ieee80211_regdomain {
...
struct ieee80211_reg_rule reg_rules[];
};
instance = kzalloc(sizeof(*mac->rd) +
sizeof(struct ieee80211_reg_rule) *
count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, reg_rules, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The assignment of 0 to variable k is never read once we break out of
the loop, so the assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The variable badworden is assigned with a value that is never read and
it is re-assigned a new value immediately afterwards. The assignment is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware can send invalid command response, the processing of
which can attempt to modify unexpected context and cause issues.
To fix this, driver should check that the command response ID is
same as the one it downloaded, and ignore processing of invalid
response.
Signed-off-by: Swati Kushwaha <swatiuma@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In set_mac_address, driver check for interfaces with same bss_type
For first STA entry, this would return 3 interfaces since all priv's have
bss_type as 0 due to kzalloc. Thus mac address gets changed for STA
unexpected. This patch adds check for first STA and avoids mac address
change. This patch also adds mac_address change for p2p based on bss_num
type.
Signed-off-by: Sharvari Harisangam <sharvari@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Unadorned '%p' has restrictive policies these days, such that it usually
just prints garbage at early boot (see
Documentation/core-api/printk-formats.rst, "kernel will print
``(ptrval)`` until it gathers enough entropy"). Annotating with %pK
(for "kernel pointer") allows the kptr_restrict sysctl to control
printing policy better.
We might just as well drop this message entirely, but this fix was easy
enough for now.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This message is pointless.
While we're at it, include the error code in the error message, which is
not pointless.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The syzbot fuzzer found a bug in the p54 USB wireless driver. The
issue involves a race between disconnect and the firmware-loader
callback routine, and it has several aspects.
One big problem is that when the firmware can't be loaded, the
callback routine tries to unbind the driver from the USB _device_ (by
calling device_release_driver) instead of from the USB _interface_ to
which it is actually bound (by calling usb_driver_release_interface).
The race involves access to the private data structure. The driver's
disconnect handler waits for a completion that is signalled by the
firmware-loader callback routine. As soon as the completion is
signalled, you have to assume that the private data structure may have
been deallocated by the disconnect handler -- even if the firmware was
loaded without errors. However, the callback routine does access the
private data several times after that point.
Another problem is that, in order to ensure that the USB device
structure hasn't been freed when the callback routine runs, the driver
takes a reference to it. This isn't good enough any more, because now
that the callback routine calls usb_driver_release_interface, it has
to ensure that the interface structure hasn't been freed.
Finally, the driver takes an unnecessary reference to the USB device
structure in the probe function and drops the reference in the
disconnect handler. This extra reference doesn't accomplish anything,
because the USB core already guarantees that a device structure won't
be deallocated while a driver is still bound to any of its interfaces.
To fix these problems, this patch makes the following changes:
Call usb_driver_release_interface() rather than
device_release_driver().
Don't signal the completion until after the important
information has been copied out of the private data structure,
and don't refer to the private data at all thereafter.
Lock udev (the interface's parent) before unbinding the driver
instead of locking udev->parent.
During the firmware loading process, take a reference to the
USB interface instead of the USB device.
Don't take an unnecessary reference to the device during probe
(and then don't drop it during disconnect).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+200d4bb11b23d929335f@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 22000 series FW that was meant to be used with hr is
also the FW that is used for hr1 and has a different RF ID.
Add support to load the hr FW when hr1 RF ID is detected.
Cc: stable@vger.kernel.org # 5.1+
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Per the 802.11 specification, vendor IEs are (at minimum) only required
to contain an OUI. A type field is also included in ieee80211.h (struct
ieee80211_vendor_ie) but doesn't appear in the specification. The
remaining fields (subtype, version) are a convention used in WMM
headers.
Thus, we should not reject vendor-specific IEs that have only the
minimum length (3 bytes) -- we should skip over them (since we only want
to match longer IEs, that match either WMM or WPA formats). We can
reject elements that don't have the minimum-required 3 byte OUI.
While we're at it, move the non-standard subtype and version fields into
the WMM structs, to avoid this confusion in the future about generic
"vendor header" attributes.
Fixes: 685c9b7750 ("mwifiex: Abort at too short BSS descriptor element")
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
change the fw of 0x02F0 platform from qu to quz
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
add few PCI ID'S for 22000 and chainge few cards structs names
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
add few PCI ID'S for 22000 and fix the wrong name for one
of the structs
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This makes boot uniformly boottime and tai uniformly clocktai, to
address the remaining oversights.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lkml.kernel.org/r/20190621203249.3909-2-Jason@zx2c4.com
Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update for
5.2. It contains all of the remaining GPLv2 and GPLv2+ updates that
were "easy" to determine by pattern matching. The ones after this are
going to be a bit more difficult and the people on the spdx list will be
discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud, always
nice to see in a diffstat.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyQYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnGQCghETUBotn1p3hTjY56VEs6dGzpHMAnRT0m+lv
kbsjBGEJpLbMRB2krnaU
=RMcT
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull still more SPDX updates from Greg KH:
"Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update
for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
that were "easy" to determine by pattern matching. The ones after this
are going to be a bit more difficult and the people on the spdx list
will be discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud,
always nice to see in a diffstat"
* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
...
- Make switch to eMMC HS400 more robust for some controllers
- Add two SDIO func API to manage re-tuning constraints
- Prevent processing SDIO IRQs when the card is suspended
MMC host:
- sdhi: Disallow broken HS400 for M3-W ES1.2, RZ/G2M and V3H
- mtk-sd: Fixup support for SDIO IRQs
- sdhci-pci-o2micro: Fixup support for tuning
Wireless BRCMFMAC (SDIO):
- Deal with expected transmission errors related to the idle states
(handled by the Always-On-Subsystem or AOS) on the SDIO-based WiFi on
rk3288-veyron-minnie, rk3288-veyron-speedy and rk3288-veyron-mickey.
-----BEGIN PGP SIGNATURE-----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=IkL6
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"Here's quite a few MMC fixes intended for v5.2-rc6. This time it also
contains fixes for a WiFi driver, which device is attached to the SDIO
interface. Patches for the WiFi driver have been acked by the
corresponding maintainers.
Summary:
MMC core:
- Make switch to eMMC HS400 more robust for some controllers
- Add two SDIO func API to manage re-tuning constraints
- Prevent processing SDIO IRQs when the card is suspended
MMC host:
- sdhi: Disallow broken HS400 for M3-W ES1.2, RZ/G2M and V3H
- mtk-sd: Fixup support for SDIO IRQs
- sdhci-pci-o2micro: Fixup support for tuning
Wireless BRCMFMAC (SDIO):
- Deal with expected transmission errors related to the idle states
(handled by the Always-On-Subsystem or AOS) on the SDIO-based WiFi
on rk3288-veyron-minnie, rk3288-veyron-speedy and
rk3288-veyron-mickey"
* tag 'mmc-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: core: Prevent processing SDIO IRQs when the card is suspended
mmc: sdhci: sdhci-pci-o2micro: Correctly set bus width when tuning
brcmfmac: sdio: Don't tune while the card is off
mmc: core: Add sdio_retune_hold_now() and sdio_retune_release()
brcmfmac: sdio: Disable auto-tuning around commands expected to fail
mmc: core: API to temporarily disable retuning for SDIO CRC errors
Revert "brcmfmac: disable command decode in sdio_aos"
mmc: mediatek: fix SDIO IRQ detection issue
mmc: mediatek: fix SDIO IRQ interrupt handle flow
mmc: core: complete HS400 before checking status
mmc: sdhi: disallow HS400 for M3-W ES1.2, RZ/G2M, and V3H
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of version 2 of the gnu general public license as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 59 temple place suite 330 boston ma 02111
1307 usa the full gnu general public license is included in this
distribution in the file called license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 8 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081207.801261482@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation see readme and copying for
more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 9 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081207.060259192@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When Broadcom SDIO cards are idled they go to sleep and a whole
separate subsystem takes over their SDIO communication. This is the
Always-On-Subsystem (AOS) and it can't handle tuning requests.
Specifically, as tested on rk3288-veyron-minnie (which reports having
BCM4354/1 in dmesg), if I force a retune in brcmf_sdio_kso_control()
when "on = 1" (aka we're transition from sleep to wake) by whacking:
bus->sdiodev->func1->card->host->need_retune = 1
...then I can often see tuning fail. In this case dw_mmc reports "All
phases bad!"). Note that I don't get 100% failure, presumably because
sometimes the card itself has already transitioned away from the AOS
itself by the time we try to wake it up. If I force retuning when "on
= 0" (AKA force retuning right before sending the command to go to
sleep) then retuning is always OK.
NOTE: we need _both_ this patch and the patch to avoid triggering
tuning due to CRC errors in the sleep/wake transition, AKA ("brcmfmac:
sdio: Disable auto-tuning around commands expected to fail"). Though
both patches handle issues with Broadcom's AOS, the problems are
distinct:
1. We want to defer (but not ignore) asynchronous (like
timer-requested) tuning requests till the card is awake. However,
we want to ignore CRC errors during the transition, we don't want
to queue deferred tuning request.
2. You could imagine that the AOS could implement retuning but we
could still get errors while transitioning in and out of the AOS.
Similarly you could imagine a seamless transition into and out of
the AOS (with no CRC errors) even if the AOS couldn't handle
tuning.
ALSO NOTE: presumably there is never a desperate need to retune in
order to wake up the card, since doing so is impossible. Luckily the
only way the card can get into sleep state is if we had a good enough
tuning to send it the command to put it into sleep, so presumably that
"good enough" tuning is enough to wake us up, at least with a few
retries.
Cc: stable@vger.kernel.org #v4.18+
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are certain cases, notably when transitioning between sleep and
active state, when Broadcom SDIO WiFi cards will produce errors on the
SDIO bus. This is evident from the source code where you can see that
we try commands in a loop until we either get success or we've tried
too many times. The comment in the code reinforces this by saying
"just one write attempt may fail"
Unfortunately these failures sometimes end up causing an "-EILSEQ"
back to the core which triggers a retuning of the SDIO card and that
blocks all traffic to the card until it's done.
Let's disable retuning around the commands we expect might fail.
Cc: stable@vger.kernel.org #v4.18+
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit 29f6589140.
After that patch landed I find that my kernel log on
rk3288-veyron-minnie and rk3288-veyron-speedy is filled with:
brcmfmac: brcmf_sdio_bus_sleep: error while changing bus sleep state -110
This seems to happen every time the Broadcom WiFi transitions out of
sleep mode. Reverting the commit fixes the problem for me, so that's
what this patch does.
Note that, in general, the justification in the original commit seemed
a little weak. It looked like someone was testing on a SD card
controller that would sometimes die if there were CRC errors on the
bus. This used to happen back in early days of dw_mmc (the controller
on my boards), but we fixed it. Disabling a feature on all boards
just because one SD card controller is broken seems bad.
Fixes: 29f6589140 ("brcmfmac: disable command decode in sdio_aos")
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Double Lo <double.lo@cypress.com>
Cc: Madhan Mohan R <madhanmohan.r@cypress.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Cc: stable@vger.kernel.org
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull networking fixes from David Miller:
"Lots of bug fixes here:
1) Out of bounds access in __bpf_skc_lookup, from Lorenz Bauer.
2) Fix rate reporting in cfg80211_calculate_bitrate_he(), from John
Crispin.
3) Use after free in psock backlog workqueue, from John Fastabend.
4) Fix source port matching in fdb peer flow rule of mlx5, from Raed
Salem.
5) Use atomic_inc_not_zero() in fl6_sock_lookup(), from Eric Dumazet.
6) Network header needs to be set for packet redirect in nfp, from
John Hurley.
7) Fix udp zerocopy refcnt, from Willem de Bruijn.
8) Don't assume linear buffers in vxlan and geneve error handlers,
from Stefano Brivio.
9) Fix TOS matching in mlxsw, from Jiri Pirko.
10) More SCTP cookie memory leak fixes, from Neil Horman.
11) Fix VLAN filtering in rtl8366, from Linus Walluij.
12) Various TCP SACK payload size and fragmentation memory limit fixes
from Eric Dumazet.
13) Use after free in pneigh_get_next(), also from Eric Dumazet.
14) LAPB control block leak fix from Jeremy Sowden"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (145 commits)
lapb: fixed leak of control-blocks.
tipc: purge deferredq list for each grp member in tipc_group_delete
ax25: fix inconsistent lock state in ax25_destroy_timer
neigh: fix use-after-free read in pneigh_get_next
tcp: fix compile error if !CONFIG_SYSCTL
hv_sock: Suppress bogus "may be used uninitialized" warnings
be2net: Fix number of Rx queues used for flow hashing
net: handle 802.1P vlan 0 packets properly
tcp: enforce tcp_min_snd_mss in tcp_mtu_probing()
tcp: add tcp_min_snd_mss sysctl
tcp: tcp_fragment() should apply sane memory limits
tcp: limit payload size of sacked skbs
Revert "net: phylink: set the autoneg state in phylink_phy_change"
bpf: fix nested bpf tracepoints with per-cpu data
bpf: Fix out of bounds memory access in bpf_sk_storage
vsock/virtio: set SOCK_DONE on peer shutdown
net: dsa: rtl8366: Fix up VLAN filtering
net: phylink: set the autoneg state in phylink_phy_change
net: add high_order_alloc_disable sysctl/static key
tcp: add tcp_tx_skb_cache sysctl
...
The kbuild documentation clearly shows that the documents
there are written at different times: some use markdown,
some use their own peculiar logic to split sections.
Convert everything to ReST without affecting too much
the author's style and avoiding adding uneeded markups.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
* HE (802.11ax) work continues
* WPA3 offloads
* work on extended key ID handling continues
* fixes to honour AP supported rates with auth/assoc frames
* nl80211 netlink policy improvements to fix some issues
with strict validation on new commands with old attrs
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEH1e1rEeCd0AIMq6MB8qZga/fl8QFAl0Dq/sACgkQB8qZga/f
l8RqFg/+MBcuqvW2xTy5o5Lbw7Drx5ROgFT2ZRAO6PTeboQ43NOBiXt2dEhDbp+w
mHChImF85px3SFMBSvuf97zlScNV6+VJraDDjoZFixt/gIZ/XsdURo5i4IGmUbfj
+LY1oPm7suC5Cold+yPicHTukFpeU7cSwceslFsecqiN5unlzIxf6gY9H7OL7WGT
s0Wis0x3y2m9mMi4cvQfHkFzplcTc5SBgPLyLQtHUNx1eySEZ+AymlNVmbGrRWr9
vaCU5W9+Wz0N6lEB/UI5y6fZzj5mhkcimGck1Os7dFeC7KWjntjT9iKIkFHWehxi
QfLcK6pGjLpPpMTQtOEfl34ZGnOyO8N9GmOLaaUaBeaZItabYJwfgbdr7NxiJvta
1cyqXek+D2G7WOa0aIrWhmwswKGBa3nIBqS/ZP/SEWLEzU1Cn0NiAD5Ba016TC4C
D+1BBXIdpQDoZCgfd6KkGs2Ynf/8N3OwHW+EwjpAu3IARTQzb6tMWSvkAuAgJt1F
dBD7NqdFhWXFfxqf9NpB8bkmpyNKM4Km6eO2HKpCg/5suKqYJ1Xj9EeQin1B+QsE
Jntj69hQ6Kj2gKBPy+RnCBFbxMNuFhpc1kmUOGj9U9aAcOntV0woVOyFGsbRmFo3
MI8aVU/gjQDCcHHD5xtJGHa11uIefXq1r2H7Um3sxKYeBsqFjP4=
=j+Um
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2019-06-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Many changes all over:
* HE (802.11ax) work continues
* WPA3 offloads
* work on extended key ID handling continues
* fixes to honour AP supported rates with auth/assoc frames
* nl80211 netlink policy improvements to fix some issues
with strict validation on new commands with old attrs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* a few memory leaks
* fixes for management frame protection security
and A2/A3 confusion (affecting TDLS as well)
* build fix for certificates
* etc.
-----BEGIN PGP SIGNATURE-----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=AHi5
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2019-06-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Various fixes, all over:
* a few memory leaks
* fixes for management frame protection security
and A2/A3 confusion (affecting TDLS as well)
* build fix for certificates
* etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no rate control algorithm that *doesn't* want to call
it internally, and calling it internally will let us modify
its behaviour in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Require that each vendor command give a policy of its sub-attributes
in NL80211_ATTR_VENDOR_DATA, and then (stricly) check the contents,
including the NLA_F_NESTED flag that we couldn't check on the outer
layer because there we don't know yet.
It is possible to use VENDOR_CMD_RAW_DATA for raw data, but then no
nested data can be given (NLA_F_NESTED flag must be clear) and the
data is just passed as is to the command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
First set of fixes for 5.2. Most important here are buffer overflow
fixes for mwifiex.
rtw88
* fix out of bounds compiler warning
* fix rssi handling to get 4x more throughput
* avoid circular locking
rsi
* fix unitilised data warning, these are hopefully the last ones so
that the warning can be enabled by default
mwifiex
* fix buffer overflows
iwlwifi
* remove not used debugfs file
* various fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJc+iptAAoJEG4XJFUm622b+cQH/R/k3d55ldIADljn8P1N2JEb
Ogc5weW2DkUgfWdeKpJ1rp7JLaRPypmY4GipA7930SEEk8Ac46WShErH/6TLxEZD
1TGDV/qTtb4QJAZzdd/bs1J8IwaCUK1BolJfcpe5cdE/4/owe2pxiYbvFxAUCGRD
IRK/FJ/ohiv6SB1zUc4ATQ0HWI2OQjiiA4O6WctUSPdHHME7u4/7/MfhD2JBvjBW
454uLf8g2QhMWPdSw/PIXcND+FwgfrS7gCO7pZz4FUy7y6062LLaM+wcgmBxEN9t
SfaH1Ur14Hb0nw4QwYAvY2loJk15iowm7jvuAfqZP9vfpxdt4LYw4KrV/Y7FU8E=
=N7kc
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2019-06-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 5.2
First set of fixes for 5.2. Most important here are buffer overflow
fixes for mwifiex.
rtw88
* fix out of bounds compiler warning
* fix rssi handling to get 4x more throughput
* avoid circular locking
rsi
* fix unitilised data warning, these are hopefully the last ones so
that the warning can be enabled by default
mwifiex
* fix buffer overflows
iwlwifi
* remove not used debugfs file
* various fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this driver is free software you can redistribute it and or modify
it under the terms of version 2 only of the gnu general public
license as published by the free software foundation it is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190113.237458590@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with this program if
not see http www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 15 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000437.237481593@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin st fifth floor boston ma 02110
1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 246 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.674189849@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with this program see
the file copying if not see http www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000435.742096485@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 3 normalized pattern(s):
gpl license summary [copyright] [c] [2008] [2014] [intel]
[corporation] [all] [rights] [reserved] [copyright] [c] [2018]
[intel] [corporation] this program is free software you can
redistribute it and or modify it under the terms of version 2 of the
gnu general public license as published by the free software
foundation this program is distributed in the hope that it will be
useful but without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details the full gnu general public
license is included in this distribution in the file called copying
gpl license summary [copyright] [c] [2008] [2014] [intel]
[corporation] [all] [rights] [reserved] this program is free
software you can redistribute it and or modify it under the terms of
version 2 of the gnu general public license as published by the free
software foundation this program is distributed in the hope that it
will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details the full gnu general
public license is included in this distribution in the file called
copying
gpl license summary [copyright] [c] [2008] [2014] [intel]
[corporation] [all] [rights] [reserved] [copyright] [c] [2015]
[intel] [deutschland] [gmbh] this program is free software you can
redistribute it and or modify it under the terms of version 2 of the
gnu general public license as published by the free software
foundation this program is distributed in the hope that it will be
useful but without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details the full gnu general public
license is included in this distribution in the file called copying
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 5 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000435.531621107@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of version 2 of the gnu general public license as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details the full gnu general public license is included in
this distribution in the file called license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 29 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000435.438503728@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of version 2 of the gnu general public license as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 64 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.894819585@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of version 2 of the gnu general public license as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin street fifth floor boston ma
02110 usa the full gnu general public license is included in this
distribution in the file called license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 9 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141334.333998390@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ifa_list is protected by rcu, yet code doesn't reflect this.
Add the __rcu annotations and fix up all places that are now reported by
sparse.
I've done this in the same commit to not add intermediate patches that
result in new warnings.
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few places in mwifiex_uap_parse_tail_ies() perform memcpy()
unconditionally, which may lead to either buffer overflow or read over
boundary.
This patch addresses the issues by checking the read size and the
destination size at each place more properly. Along with the fixes,
the patch cleans up the code slightly by introducing a temporary
variable for the token size, and unifies the error path with the
standard goto statement.
Reported-by: huangwen <huangwen@venustech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The TLC_MNG_CONFIG sync cmd sent by the rs leads to a kernel warning
of sleeping while in rcu read-side critical section. The fix is to
change the command to be ASYNC (not blocking for the response anymore).
Signed-off-by: Lior Cohen <lior2.cohen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the error handling code of iwl_req_fw_callback(), iwl_dealloc_ucode()
is called to free data. In iwl_drv_stop(), iwl_dealloc_ucode() is called
again, which can cause double-free problems.
To fix this bug, the call to iwl_dealloc_ucode() in
iwl_req_fw_callback() is deleted.
This bug is found by a runtime fuzzing tool named FIZZER written by us.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Lorenzo Bianconi