The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
The dpaa2-eth driver now has support for connecting to its associated
PHY device found through standard OF bindings.
This happens when the DPNI object (that the driver probes on) gets
connected to a DPMAC. When that happens, the device tree is looked up by
the DPMAC ID, and the associated PHY bindings are found.
The old logic of handling the net device's link state by hand still
needs to be kept, as the DPNI can be connected to other devices on the
bus than a DPMAC: other DPNI, DPSW ports, etc. This logic is only
engaged when there is no DPMAC (and therefore no phylink instance)
attached.
The MC firmware support multiple type of DPMAC links: TYPE_FIXED,
TYPE_PHY. The TYPE_FIXED mode does not require any DPMAC management from
Linux side, and as such, the driver will not handle such a DPMAC.
Although PHYLINK typically handles SFP cages and in-band AN modes, for
the moment the driver only supports the RGMII interfaces found on the
LX2160A. Support for other modes will come later.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the function is called at every link up event, although the
FQID values will only change when the DPNI is disconnected from the
current object and reconnected to a different one.
The patch also avoids the forward declaration of update_tx_fqids.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change, unbinding the QMan portals did not trigger a
corresponding unbinding of the dpaa_eth making use of it; the first
QMan portal related operation issued afterwards crashed the kernel.
The device link ensures the dpaa_eth dependency upon the qman portal
used is honoured at the QMan portal removal.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure all the frames that are in flight have time to be processed
before the interface is completely brought down. Add a missing delay
for the Rx path.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
User reports that an application making an (incorrect) call to
restart AN on a fixed link DPAA interface triggers an error in
the kernel log while the returned EINVAL should be enough.
Reported-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this change, the frames dropped on receive or transmit
were not displayed in the ethtool statistics, leaving the dropped
frames unaccounted for.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a page to store the scatter gather table on the transmit path.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of reading skb fields, use information from the DPAA frame
descriptor.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dpaa_cleanup_tx_fd() function is called by the frame transmit
confirmation callback but also on several error paths. This function
is reading the transmit timestamp value. Avoid reading an invalid
timestamp value on the error paths.
Fixes: 4664856e9c ("dpaa_eth: add support for hardware timestamping")
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA unmapping is required before accessing the HW provided timestamping
information.
Fixes: 4664856e9c ("dpaa_eth: add support for hardware timestamping")
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the buffers used for reception from netdev_frags to pages.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the DPAA Ethernet driver is using three buffer pools
for each interface, with three different sizes for the buffers
provided for the FMan reception path. This patch reduces the
number of buffer pools to one per interface. This change is in
preparation of another, that will be switching from netdev_frags
to page backed buffers for the receive path.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use platform_get_irq_byname_optional() and platform_get_irq_optional()
instead of platform_get_irq_byname() and platform_get_irq() for optional
IRQs to avoid below error message during probe:
[ 0.795803] fec 30be0000.ethernet: IRQ pps not found
[ 0.800787] fec 30be0000.ethernet: IRQ index 3 not found
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Failed to get irq using name is NOT fatal as driver will use index
to get irq instead, use platform_get_irq_byname_optional() instead
of platform_get_irq_byname() to avoid below error message during
probe:
[ 0.819312] fec 30be0000.ethernet: IRQ int0 not found
[ 0.824433] fec 30be0000.ethernet: IRQ int1 not found
[ 0.829539] fec 30be0000.ethernet: IRQ int2 not found
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer bdp is being assigned with a value that is never
read, so the assignment is redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects the SPDX License Identifier style in
header files related to DPAA2 Ethernet driver supporting
Freescale SoCs with DPAA2. For C header files
Documentation/process/license-rules.rst mandates C-like comments
(opposed to C source files where C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newline was missing at the end of the error message.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused struct member second_largest_buf_size. Also, an out of
bounds access would have occurred in the removed code if there was only
one buffer pool in use.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DPAA Ethernet driver is using the FMan MAC as the device for DMA
mapping. This is not actually correct, as the real DMA device is the
FMan port (the FMan Rx port for reception and the FMan Tx port for
transmission). Changing the device used for DMA mapping to the Fman
Rx and Tx port devices.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an API that retrieves the 'struct device' that the specified FMan
port probed against. The new API will be used in a subsequent patch
that corrects the DMA devices used by the dpaa_eth driver.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Condition was previously checked, removing duplicate code.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the DPAA 1 Ethernet driver gets probed before the QBMan driver it will
cause a boot crash. Add predictability in the probing order by deferring
the Ethernet driver probe after QBMan and portals by using the recently
introduced QBMan APIs.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The liodn base registers are specific to PAMU based NXP systems and are
reserved on SMMU based ones. Don't access them unless PAMU is compiled in.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on when MC connects the DPNI to a MAC, Tx FQIDs may
not be available during probe time.
Read the FQIDs each time the link goes up to avoid using invalid
values. In case an error occurs or an invalid value is retrieved,
fall back to QDID-based enqueueing.
Fixes: 1fa0f68c92 ("dpaa2-eth: Use FQ-based DPIO enqueue API")
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IRQ for the DPNI endpoint change event, resolving the issue
when a dynamically created DPNI gets a randomly generated hw address
when the endpoint is a DPMAC object.
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Throughout the driver there are several places where we wait
indefinitely for DPIO portal commands to be executed, while
the portal returns a busy response code.
Even though in theory we are guaranteed the portals become
available eventually, in practice the QBMan hardware module
may become unresponsive in various corner cases.
Make sure we can never get stuck in an infinite while loop
by adding a retry counter for all portal commands.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't print error message for a successful return value.
Fixes: d84c3a4ded ("dpaa2-eth: Add new DPNI statistics counters")
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove one function call whose result was not used anywhere.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "priv->if_mode" is type phy_interface_t which is an enum. In this
context GCC will treat the enum as an unsigned int so this error
handling is never triggered.
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warning:
drivers/net/ethernet/freescale/gianfar.c:2070:6:
warning: symbol 'reset_gfar' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Historically, gianfar only used phy-connection-type DT property when
connected to PHY in the rgmii-id mode. It ignored the property otherwise,
relying on the connection type auto-detection carried out by MAC and
providing that reconstructed mode to of_phy_connect(). It also did not
consider alternative phy-mode property at all.
Make the driver properly query DT node for PHY connection type first and
use an obtained value if it was specified there. Otherwise, if a particular
DT relies on connection type auto-detection, fall back to reconstructing
the value from MAC registers, as before.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove now unused macro and structure definitions from gianfar.h that have
accumulated there over time.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make functions that do not have callers outside the translation unit they
are defined in static.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove forward declarations of various static functions located in two
driver implementation files and rearrange the corresponding definitions
accordingly.
This patch only introduces mechanical changes, namely it removes forward
declarations and moves function definitions around; it does not change any
functionality.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with firmware version MC10.18.0, a new counter for in flight
Tx frames is offered. Use it when bringing down the interface to
determine when all pending Tx frames have been processed by hardware
instead of sleeping a fixed amount of time.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent firmware versions expose more DPNI counters.
Export relevant ones via ethtool -S.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we prepare to read more pages from the DPNI stat counters,
reorganize the code a bit to make it easier to extend.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call to 'pci_free_irq_vectors()' are missing both in the error handling
path of the probe function, and in the remove function.
Add them.
Fixes: 19971f5ea0 ("enetc: add PTP clock driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with firmware version MC10.18.0, we have support for
L2 flow control. Asymmetrical configuration (Rx or Tx only) is
supported, but not pause frame autonegotioation.
Pause frame configuration is done via ethtool. By default, we start
with flow control enabled on both Rx and Tx. Changes are propagated
to hardware through firmware commands, using two flags (PAUSE,
ASYM_PAUSE) to specify Rx and Tx pause configuration, as follows:
PAUSE | ASYM_PAUSE | Rx pause | Tx pause
----------------------------------------
0 | 0 | disabled | disabled
0 | 1 | disabled | enabled
1 | 0 | enabled | enabled
1 | 1 | enabled | disabled
The hardware can automatically send pause frames when the number
of buffers in the pool goes below a predefined threshold. Due to
this, flow control is incompatible with Rx frame queue taildrop
(both mechanisms target the case when processing of ingress
frames can't keep up with the Rx rate; for large frames, the number
of buffers in the pool may never get low enough to trigger pause
frames as long as taildrop is enabled). So we set pause frame
generation and Rx FQ taildrop as mutually exclusive.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever a link state change occurs, we get notified and save
the new link settings in the device's private data. In ethtool
get_link_ksettings, use the stored state instead of interrogating
the firmware each time.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only support fixed-link for now, so there is no point in
offering users the option to change link settings via ethtool.
Functionally there is no change, since firmware prevents us from
changing link parameters anyway.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
IEEE 802.3ae clause 45 defines a modified MDIO protocol that uses a two
staged access model in order to increase the address space.
This patch adds support for C45 MDIO read and write accesses, which are
used whenever the MII_ADDR_C45 flag in the regnum argument is set.
In case it is not set, C22 accesses are used as before.
Signed-off-by: Marco Hartmann <marco.hartmann@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Because we don't care about the individual files, we can remove the
stored dentry for the files, as they are not needed to be kept track of
at all.
Cc: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller