Two users of ar9170 devices have now reported their cards
have been programmed with a regulatory domain of 0x8000.
This is not a valid regulatory domain as such these users were
unable to use these devices. Since this doesn't seem to be
a device EEPROM corruption we must treat it specially. It
may have been possible the manufacturer intended to use 0x0
as the regulatory domain and that would ultimately yield
to US but since we cannot get confirmationf or this we
default this special case to one of our world regulatory
domains, specifically 0x64.
Reported-by: DavidFreeman on #linux-wireless
Reported-by: Joerg Albert <jal2@gmx.de>
Cc: Christian Lamparter <chunkeey@web.de>,
Cc: Stephen Chen <stephen.chen@atheros.com>
Cc: David Quan <david.quan@atheros.com>
Cc: Tony Yang <tony.yang@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a potential NULL dereference bug during
error handling in p54spi_probe.
This bug was discovered by smatch:
(http://repo.or.cz/w/smatch.git).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For AP mode we must tune ANI specially for 2 GHz and
for 5 GHz. We mask in only the flags we want to toggle
on ath9k_hw_ani_control() through the ah->ani_function
bitmask, this will take care of ignoring changes during
ANI reset which we were disabling before.
Testedy-by: Steven Luo <steven@steven676.net>
Cc: Bennyam Malavazi <bennyam.malavazi@atheros.com>
Cc: Jouni Malinen <jouni.malinen@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit below changed the semantics of rt2x00_check_rev so that it no
longer checked the bottom 4 bits of the rev were non-zero. During that
conversion this part of the check was not propogated to the rt2500usb
initialisation.
commit 358623c22c
Author: Ivo van Doorn <ivdoorn@gmail.com>
Date: Tue May 5 19:46:08 2009 +0200
rt2x00: Simplify rt2x00_check_rev
Without this check rt73 devices are miss recognised as rt2500 devices and
two drivers are loaded. Preventing the device being used. Reinstate this
check.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When rtl8187 is unloaded and CONFIG_RTL8187_LEDS is set, the kernel
may oops when the module is unloaded as the workqueue for led_on was
not being cancelled.
This patch fixes the problem reported in
http://marc.info/?l=linux-wireless&m=124742957615781&w=2.
Reported-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel Roskin reported some issues with using AP mode without
nohwcrypt=1. Most likely this is similar to the problem fixed
some time ago in ath9k by 3f53dd64f1,
"ath9k: Fix hw crypto configuration for TKIP in AP mode."
That only affects TKIP but it's easiest to just disable that and
WEP too until we get a proper fix in.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Once the "data" pointer is freed, we can't be iterating
to the next item in the list any more so we need to use
list_for_each_entry_safe with a temporary variable.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If you rmmod the module while associated, frames might
be transmitted during unregistration -- which will crash
if the hwsim%d interface is unregistered first, so only
do that after all the virtual wiphys are gone.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The byte count table is only used for aggregation. Updating it
in other cases caused fragmented frames to be dropped.
This fixes http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=2004
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This changes the power_level file to adhere to the "one value
per file" sysfs rule. The user will know which power level was
requested as it will be the number just written to this file. It
is thus not necessary to create a new sysfs file for this value.
In addition it fixes a problem where powertop's parsing expects
this value to be the first value in this file without any descriptions.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver private data is now based on wiphy. So we should not
touch the private data after wiphy_free() is called. The patch
fixes the potential NULL pointer dereference by making the
iwm_wdev_free() the last one on the interface removal path.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a problem when a device is stopped while in the
bus-off state. Then the carrier remains off forever.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@skynet.be>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If dev_alloc_skb() failed in can_restart(), the device was left behind
in the bus-off state. This patch restarts the device nevertheless.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicated #include('s) in
drivers/net/can/sja1000/sja1000.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rain_maker@root-forum.org wrote:
> Hello cesar,
>
> In a recent thread in a german linux forum, a user reported his PIC
> NIC not being recognized by the kernel.
>
> Fortunately he provided enough information and I was able to help him
> and get the device working with the sc92031 driver.
>
> The device ID is [1088:2031] (Vendor is called "Microcomputer Systems
> (M) Son"), here is the respective thread in "ubuntuusers.de"
>
> http://forum.ubuntuusers.de/topic/lankarte-unter-xubuntu-wird-nicht-erkannt/
>
> (Although you might not speak german, the code provided will show
> you, that the device is actually working with your driver).
>
> It would be nice, if you include this new device ID to the
> sc92031-driver.
>
> Regards,
>
> Axel Köllhofer (aka Rain_Maker)
Cc: rain_maker@root-forum.org
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
3c589_cs:
re-initialize the multicast in the tc589_reset,
and spin_lock the set_multicast_list function.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check temperature for all PCI functions, that can allow
graceful shutdown of all interfaces on the overheated card.
Old code was only monitoring temperature for function 0 only.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netxen: fix deadlock on dev close
The tx ring accounting fix in commit cb2107be43
("netxen: fix tx ring accounting") introduced intermittent
deadlock when inteface is going down.
This was possibly combined effect of speculative tx pause,
calling netif_tx_lock instead of queue lock and unclean
synchronization with napi which could end up unmasking
interrupt.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Use D3 reset context deletion for NX2031, it cleans up
more resources in the firmware.
o Release rx buffers after hardware context has been reset.
o Delete tx context after rx context, some firmware control
commands are sent on tx context, so it should be the last
to go.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network driver for the SPI version of the Micrel KS8851
network chip.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mac driver support for evaluation board based on w90p910.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel has used a stale email address of Andreas for a few years.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver received an EEM packet with CRC option enabled, driver must
compute and check the CRC of the Ethernet data. Previous version computes CRC
on Ethernet data plus the original CRC value. Skbuff is correctly trimed but
the old length is used when CRC is computed.
Signed-off-by: Vincent CUISSARD <vincent.cuissard@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove debug DPRINTK in DCB mode netlink interface.
Signed-off-by: Lucy Liu <lucy.liu@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change clears the address data block memory space, which is needed for
the 82598 which does not have a SAN MAC.
Signed-off-by: Lucy Liu <lucy.liu@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit changes to shutdown path broke startup on some systems.
revert commit c0bad0f2e4
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
E100 places it's RX packet descriptors inside skb->data and uses them
with bidirectional streaming DMA mapping. Unfortunately it fails to
transfer skb->data ownership to the device after it reads the
descriptor's status, breaking on non-coherent (e.g., ARM) platforms.
This have to be converted to use coherent memory for the descriptors.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bonding device forbids slave device of different types under the same
master.
However, it is possible for a bonding master to change type during its
lifetime. This can be either from ARPHRD_ETHER to ARPHRD_INFINIBAND
or the other way arround. The change of type requires device level
multicast address cleanup because device level multicast addresses
depend on the device type.
The patch adds a call to dev_close() before the bonding master changes
type and dev_open() just after that.
In the example below I enslaved an IPoIB device (ib0) under
bond0. Since each bonding master starts as device of type ARPHRD_ETHER
by default, a change of type occurs when ib0 is enslaved.
This is how /proc/net/dev_mcast looks like without the patch
5 bond0 1 0 00ffffffff12601bffff000000000001ff96ca05
5 bond0 1 0 01005e000116
5 bond0 1 0 01005e7ffffd
5 bond0 1 0 01005e000001
5 bond0 1 0 333300000001
6 ib0 1 0 00ffffffff12601bffff000000000001ff96ca05
6 ib0 1 0 333300000001
6 ib0 1 0 01005e000001
6 ib0 1 0 01005e7ffffd
6 ib0 1 0 01005e000116
6 ib0 1 0 00ffffffff12401bffff00000000000000000001
6 ib0 1 0 00ffffffff12601bffff00000000000000000001
and this is how it looks like after the patch.
5 bond0 1 0 00ffffffff12601bffff000000000001ff96ca05
5 bond0 1 0 00ffffffff12601bffff00000000000000000001
5 bond0 1 0 00ffffffff12401bffff0000000000000ffffffd
5 bond0 1 0 00ffffffff12401bffff00000000000000000116
5 bond0 1 0 00ffffffff12401bffff00000000000000000001
6 ib0 1 0 00ffffffff12601bffff000000000001ff96ca05
6 ib0 1 0 00ffffffff12401bffff00000000000000000116
6 ib0 1 0 00ffffffff12401bffff0000000000000ffffffd
6 ib0 2 0 00ffffffff12401bffff00000000000000000001
6 ib0 2 0 00ffffffff12601bffff00000000000000000001
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parentheses are required or the comparison occurs before the bitand.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit adeab1afb7.
As Alan Cox explained, the TTY layer changes that went recently
to get rid of the tty->low_latency stuff fixes this already,
and even for -stable it's the ->low_latency changes that should
go in to fix this, rather than this patch.
Signed-off-by: David S. Miller <davem@davemloft.net>
spin_unlock_irq() will enable interrupt in net_send_packet(),
this patch changes it to spin_lock_irqsave/spin_lock_irqrestore,
so that it doesn't enable interrupts when already disabled,
and netconsole would work properly over cs89x0/isa-skeleton.
Call trace:
netconsole write_msg()
{
...
-> spin_lock_irqsave();
-> netpoll_send_udp()
-> netpoll_send_skb()
-> net_send_packet()
->...
-> spin_unlock_irqrestore();
...
}
Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't forget to unlock a mutex in phy_scan_fixups on a fail path.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
forward declaration of inline function should be avoided, or
old gcc cannot compile.
Reported-by: Teck Choon Giam <giamteckchoon@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix duplicate testing of MCAST flag
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Jay Cliburn <jcliburn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guido Trentalancia reports:
I am trying to use the kiss driver in the Linux kernel that is being
shipped with Fedora 10 but unfortunately I get the following oops:
mkiss: AX.25 Multikiss, Hans Albas PE1AYX
mkiss: ax0: crc mode is auto.
ADDRCONF(NETDEV_CHANGE): ax0: link becomes ready
------------[ cut here ]------------
WARNING: at kernel/softirq.c:77 __local_bh_disable+0x2f/0x83() (Not
tainted)
[...]
unloaded: microcode]
Pid: 0, comm: swapper Not tainted 2.6.27.25-170.2.72.fc10.i686 #1
[<c042ddfb>] warn_on_slowpath+0x65/0x8b
[<c06ab62b>] ? _spin_unlock_irqrestore+0x22/0x38
[<c04228b4>] ? __enqueue_entity+0xe3/0xeb
[<c042431e>] ? enqueue_entity+0x203/0x20b
[<c0424361>] ? enqueue_task_fair+0x3b/0x3f
[<c041f88c>] ? resched_task+0x3a/0x6e
[<c06ab62b>] ? _spin_unlock_irqrestore+0x22/0x38
[<c06ab4e2>] ? _spin_lock_bh+0xb/0x16
[<c043255b>] __local_bh_disable+0x2f/0x83
[<c04325ba>] local_bh_disable+0xb/0xd
[<c06ab4e2>] _spin_lock_bh+0xb/0x16
[<f8b6f600>] mkiss_receive_buf+0x2fb/0x3a6 [mkiss]
[<c0572a30>] flush_to_ldisc+0xf7/0x198
[<c0572b12>] tty_flip_buffer_push+0x41/0x51
[<f89477f2>] ftdi_process_read+0x375/0x4ad [ftdi_sio]
[<f8947a5a>] ftdi_read_bulk_callback+0x130/0x138 [ftdi_sio]
[<c05d4bec>] usb_hcd_giveback_urb+0x63/0x93
[<c05ea290>] uhci_giveback_urb+0xe5/0x15f
[<c05eaabf>] uhci_scan_schedule+0x52e/0x767
[<c05f6288>] ? psmouse_handle_byte+0xc/0xe5
[<c054df78>] ? acpi_ev_gpe_detect+0xd6/0xe1
[<c05ec5b0>] uhci_irq+0x110/0x125
[<c05d4834>] usb_hcd_irq+0x40/0xa3
[<c0465313>] handle_IRQ_event+0x2f/0x64
[<c046642b>] handle_level_irq+0x74/0xbe
[<c04663b7>] ? handle_level_irq+0x0/0xbe
[<c0406e6e>] do_IRQ+0xc7/0xfe
[<c0405668>] common_interrupt+0x28/0x30
[<c056821a>] ? acpi_idle_enter_simple+0x162/0x19d
[<c0617f52>] cpuidle_idle_call+0x60/0x92
[<c0403c61>] cpu_idle+0x101/0x134
[<c069b1ba>] rest_init+0x4e/0x50
=======================
---[ end trace b7cc8076093467ad ]---
------------[ cut here ]------------
WARNING: at kernel/softirq.c:136 _local_bh_enable_ip+0x3d/0xc4()
[...]
Pid: 0, comm: swapper Tainted: G W 2.6.27.25-170.2.72.fc10.i686
[<c042ddfb>] warn_on_slowpath+0x65/0x8b
[<c06ab62b>] ? _spin_unlock_irqrestore+0x22/0x38
[<c04228b4>] ? __enqueue_entity+0xe3/0xeb
[<c042431e>] ? enqueue_entity+0x203/0x20b
[<c0424361>] ? enqueue_task_fair+0x3b/0x3f
[<c041f88c>] ? resched_task+0x3a/0x6e
[<c06ab62b>] ? _spin_unlock_irqrestore+0x22/0x38
[<c06ab4e2>] ? _spin_lock_bh+0xb/0x16
[<f8b6f642>] ? mkiss_receive_buf+0x33d/0x3a6 [mkiss]
[<c04325f9>] _local_bh_enable_ip+0x3d/0xc4
[<c0432688>] local_bh_enable_ip+0x8/0xa
[<c06ab54d>] _spin_unlock_bh+0x11/0x13
[<f8b6f642>] mkiss_receive_buf+0x33d/0x3a6 [mkiss]
[<c0572a30>] flush_to_ldisc+0xf7/0x198
[<c0572b12>] tty_flip_buffer_push+0x41/0x51
[<f89477f2>] ftdi_process_read+0x375/0x4ad [ftdi_sio]
[<f8947a5a>] ftdi_read_bulk_callback+0x130/0x138 [ftdi_sio]
[<c05d4bec>] usb_hcd_giveback_urb+0x63/0x93
[<c05ea290>] uhci_giveback_urb+0xe5/0x15f
[<c05eaabf>] uhci_scan_schedule+0x52e/0x767
[<c05f6288>] ? psmouse_handle_byte+0xc/0xe5
[<c054df78>] ? acpi_ev_gpe_detect+0xd6/0xe1
[<c05ec5b0>] uhci_irq+0x110/0x125
[<c05d4834>] usb_hcd_irq+0x40/0xa3
[<c0465313>] handle_IRQ_event+0x2f/0x64
[<c046642b>] handle_level_irq+0x74/0xbe
[<c04663b7>] ? handle_level_irq+0x0/0xbe
[<c0406e6e>] do_IRQ+0xc7/0xfe
[<c0405668>] common_interrupt+0x28/0x30
[<c056821a>] ? acpi_idle_enter_simple+0x162/0x19d
[<c0617f52>] cpuidle_idle_call+0x60/0x92
[<c0403c61>] cpu_idle+0x101/0x134
[<c069b1ba>] rest_init+0x4e/0x50
=======================
---[ end trace b7cc8076093467ad ]---
mkiss: ax0: Trying crc-smack
mkiss: ax0: Trying crc-flexnet
The issue was, that the locking code in mkiss was assuming it was only
ever being called in process or bh context. Fixed by converting the
involved locking code to use irq-safe locks.
Review of other networking line disciplines shows that 6pack, both sync
and async PPP and STRIP have similar issues. The ppp_async one is the
most interesting one as it sorts out half of the issue as far back as
2004 in commit http://git.kernel.org/?p=linux/kernel/git/tglx/history.git;a=commitdiff;h=2996d8deaeddd01820691a872550dc0cfba0c37d
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: Guido Trentalancia <guido@trentalancia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev() used to install a default implementation of this
operation, but it must now be explicitly installed in struct
net_device_ops.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev() used to install default implementations of these
operations, but they must now be explicitly installed in struct
net_device_ops.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c3a8c5b6 ("cxgb3: move away from LLTX") exposed a bug in how
cxgb3 looks up the netdev_queue it stashes away in a qset during
initialization. For multiport devices, the TX queue index it uses is
offset by the first_qset index of each port. This leads to a crash
once LLTX is removed, since hard_start_xmit is called with one TX
queue lock held, while the TX reclaim timer task grabs a different
(wrong) TX queue lock when it frees skbs.
Fix this by removing the first_qset offset used to look up the TX
queue passed into t3_sge_alloc_qset() from setup_sge_qsets().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix coexistence of Fiber Channel over Ethernet (FCoE) and Flow Director (FDIR)
in 82599 and remove the disabling of FDIR when FCoE is enabled.
Currently, FDIR is turned off when FCoE is enabled under the assumption that
FCoE is always enabled with DCB being turned on. However, FDIR does not have
to be turned off all the time when FCoE is enabled since FCoE can be enabled
without DCB being turned on, e.g., use link pause only. This patch makes sure
that when DCB is turned on or off, FDIR is turned on or off correspondingly;
and when FCoE is enabled, it does not disable FDIR, rather, it will have FDIR
set up properly so FCoE and FDIR can coexist regardless of DCB being on or off.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the mainline kernel, p54usb will fail because the TX queue length can
become < 0. This problem has been reported as Bugzilla #13725. The failure
is expressed by the following message in the logs:
WARNING: at net/mac80211/tx.c:1325 ieee80211_tx+0x23c/0x298 [mac80211]()
Hardware name: HP Pavilion dv2700 Notebook PC
tx refused but queue active
This problem has been recently observed in the wireless-testing tree, where
a full solution is being tested. That fix is too invasive for 2.6.31-rcX,
but the simple change supplied here will prevent the failure.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Atheros top level menu needs a "depends WLAN_80211" to properly indent
within menuconfig and xconfig interfaces.
This is purely a visual issue but it effects all subsequent drivers.
The issue is the top level menu does not include a dependency on
WLAN_80211 so within the tree structure, Atheros is at the same level as
WLAN_80211 but when WLAN_80211 collapsed, the menu disappears along with
all subsequent drives, so it is really a subordinate.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a race condition -- started can be set to true
before channel is set due to the way mac80211 callbacks
currently work (->start should probably pass the channel
we would like to have initially). For now simply add a
check to hwsim to avoid dereferencing the NULL channel
pointer.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added support for the Broadcom 4318E chipset on PCMCIA/CF cards. The
4318E can do 802.11A/B/G, only B and G mode are supported in b43.
Signed-off-by: Clyde McPherson <ccmcphe@verizon.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yevgen Kotikov reported success on the sourceforge zd1211-devs list
with the following details:
Brand/retail: SONY IFU-WLM2
USB-IDs: Vendor: 0x054C Device: 0x0257
chip ID: zd1211b chip 054c:0257 v4802 high 00-0b-6b AL2230_RF pa0 -----
FCC ID: unknown
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Tested-by: Yevgen Kotikov <yevgen.kotikov@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On a shuttle machine here we got 07b8:6001 device, handled by zd1211rw, which does not work.
Scanning is OK but association does not work, we get "direct probe to AP xxx timed out"
It appears that this simple patch makes the device work perfectly.
This id was already there in initial import of the driver so I don't know if it has ever been
working as ZD1211 (which would mean they changed it and kept the id :( ).
Signed-off-by: Pascal Terjan <pterjan@mandriva.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the r6040 device IRQ line is shared we will enter the driver
interrupt service routine, mask off the device interrupt enable
register (MIER) and return with IRQ_NONE, we would then leave the
device with interrupts disabled, this patch fixes that issue.
Reported-by: Steve Holland <sdh4@iastate.edu>
Signed-off-by: Joe Chou <joe.chou@rdc.com.tw>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check that network interface is running before changing its MAC address.
Otherwise, rxch is accessed when it's NULL - causing a kernel oops.
Moreover, check that the new MAC address is valid.
Signed-off-by: Pablo Bitton <pablo.bitton@gmail.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Tested-by: Chaithrika U S <chaithrika@ti.com>
[tested on DM6467 EVM]
Signed-off-by: David S. Miller <davem@davemloft.net>
Luis R. Rodriguez