If the USB controller can wake up the system (which is the case for
example with the Mediatek USB3 IP) then we must not call phy_exit during
suspend to ensure that the USB controller doesn't have to re-enumerate
the devices during resume.
However, if the USB controller cannot wake up the system (which is the
case for example on various TI platforms using a dwc3 controller) then
we must call phy_exit during suspend. Otherwise the PHY driver keeps the
clocks enabled, which prevents the system from reaching the lowest power
levels in the suspend state.
Solve this by introducing two new functions in the PHY wrapper which are
dedicated to the suspend and resume handling.
If the controller can wake up the system the new usb_phy_roothub_suspend
function will simply call usb_phy_roothub_power_off. However, if wake up
is not supported by the controller it will also call
usb_phy_roothub_exit.
The also new usb_phy_roothub_resume function takes care of calling
usb_phy_roothub_init (if the controller can't wake up the system) in
addition to usb_phy_roothub_power_on.
Fixes: 07dbff0ddb ("usb: core: add a wrapper for the USB PHYs on the HCD")
Fixes: 178a0bce05 ("usb: core: hcd: integrate the PHY wrapper into the HCD core")
Reported-by: Roger Quadros <rogerq@ti.com>
Suggested-by: Roger Quadros <rogerq@ti.com>
Suggested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before this patch usb_phy_roothub_init served two purposes (from a
caller's point of view - like hcd.c):
- parsing the PHYs and allocating the list entries
- calling phy_init on each list entry
While this worked so far it has one disadvantage: if we need to call
phy_init for each PHY instance then the existing code cannot be re-used.
Solve this by splitting off usb_phy_roothub_alloc which only parses the
PHYs and allocates the list entries.
usb_phy_roothub_init then gets a struct usb_phy_roothub and only calls
phy_init on each PHY instance (along with the corresponding cleanup if
that failed somewhere).
This is a preparation step for adding proper suspend support for some
hardware that requires phy_exit to be called during suspend and phy_init
to be called during resume.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On chromebooks we depend on wakeup count to identify the wakeup source.
But currently USB devices do not increment the wakeup count when they
trigger the remote wake. This patch addresses the same.
Resume condition is reported differently on USB 2.0 and USB 3.0 devices.
On USB 2.0 devices, a wake capable device, if wake enabled, drives
resume signal to indicate a remote wake (USB 2.0 spec section 7.1.7.7).
The upstream facing port then sets C_PORT_SUSPEND bit and reports a
port change event (USB 2.0 spec section 11.24.2.7.2.3). Thus if a port
has resumed before driving the resume signal from the host and
C_PORT_SUSPEND is set, then the device attached to the given port might
be the reason for the last system wakeup. Increment the wakeup count for
the same.
On USB 3.0 devices, a function may signal that it wants to exit from device
suspend by sending a Function Wake Device Notification to the host (USB3.0
spec section 8.5.6.4) Thus on receiving the Function Wake, increment the
wakeup count.
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The phys has already been initialized when add primary hcd,
including usb2 phys and usb3 phys also if exist, so needn't
re-parse "phys" property again.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the new PHY wrapper in place we can now handle multiple PHYs.
Remove the code which handles only one generic PHY as this is now
covered (with support for multiple PHYs as well as suspend/resume
support) by the new PHY wrapper.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.con>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This integrates the PHY wrapper into the core hcd infrastructure.
Multiple PHYs which are part of the HCD's device tree node are now
managed (= powered on/off when needed), by the new usb_phy_roothub code.
Suspend and resume is also supported, however not for
runtime/auto-suspend (which is triggered for example when no devices are
connected to the USB bus). This is needed on some SoCs (for example
Amlogic Meson GXL) because if the PHYs are disabled during auto-suspend
then devices which are plugged in afterwards are not seen by the host.
One example where this is required is the Amlogic GXL and GXM SoCs:
They are using a dwc3 USB controller with up to three ports enabled on
the internal roothub. Each port has it's own PHY which must be enabled
(if one of the PHYs is left disabled then none of the USB ports works at
all).
The new logic works on the Amlogic GXL and GXM SoCs because the dwc3
driver internally creates a xhci-hcd which then registers a HCD which
then triggers our new PHY wrapper.
USB controller drivers can opt out of this by setting
"skip_phy_initialization" in struct usb_hcd to true. This is identical
to how it works for a single USB PHY, so the "multiple PHY" handling is
disabled for drivers that opted out of the management logic of a single
PHY.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.con>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB HCD core driver parses the device-tree node for "phys" and
"usb-phys" properties. It also manages the power state of these PHYs
automatically.
However, drivers may opt-out of this behavior by setting "phy" or
"usb_phy" in struct usb_hcd to a non-null value. An example where this
is required is the "Qualcomm USB2 controller", implemented by the
chipidea driver. The hardware requires that the PHY is only powered on
after the "reset completed" event from the controller is received.
A follow-up patch will allow the USB HCD core driver to manage more than
one PHY. Add a new "skip_phy_initialization" bitflag to struct usb_hcd
so drivers can opt-out of any PHY management provided by the USB HCD
core driver.
This also updates the existing drivers so they use the new flag if they
want to opt out of the PHY management provided by the USB HCD core
driver. This means that for these drivers the new "multiple PHY"
handling (which will be added in a follow-up patch) will be disabled as
well.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.con>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work with
const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While unlink an urb, if the urb has been programmed in the controller,
the controller driver might do some hw related actions to tear down the
urb.
Currently usb_hcd_flush_endpoint() passes each urb from the head of the
endpoint's urb_list to the controller driver, which could make the
controller driver think each urb has been programmed and take the
unnecessary actions for each urb.
This patch changes the behavior in usb_hcd_flush_endpoint() to pass the
urbs from the tail of the list, to avoid any unnecessary actions in an
controller driver.
Cc: stable@vger.kernel.org # v4.4+
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make usb_hc_died() clear the HCD_FLAG_RH_RUNNING flag for the shared
HCD and set HCD_FLAG_DEAD for it, in analogy with what is done for
the primary one.
Among other thigs, this prevents check_root_hub_suspended() from
returning -EBUSY for dead HCDs which helps to work around system
suspend issues in some situations.
This actually fixes occasional suspend failures on one of my test
machines.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In an attempt to work around a pinmux over-allocation issue in driver
core, commit dc5878abf4 ("usb: core: move root hub's device node
assignment after it is added to bus") moved the device-tree node
assignment until after the root hub had been registered.
This not only makes the device-tree node unavailable to the usb driver
during probe, but also prevents the of_node from being linked to in
sysfs and causes a race with user-space for the (recently added) devspec
attribute.
Use the new device_set_of_node_from_dev() helper to reuse the node of
the sysdev device, something which now prevents driver core from trying
to reclaim any pinctrl pins during probe.
Fixes: dc5878abf4 ("usb: core: move root hub's device node assignment after it is added to bus")
Fixes: 51fa91475e ("usb/core: Added devspec sysfs entry for devices behind the usb hub")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update usb_hcd_map_urb_for_dma() to check for an URB's setup_packet and
transfer_buffer sanity. We first check that urb->setup_packet is neither
coming from vmalloc space nor is an on stack buffer, and if that's the
case, produce a warning and return an error. For urb->transfer_buffer
there is an existing is_vmalloc_addr() check so we just supplement that
with an object_is_on_stack() check, produce a warning if that is the case
and also return an error.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Format specifier %p can leak kernel addresses while not valuing the
kptr_restrict system settings. When kptr_restrict is set to (1), kernel
pointers printed using the %pK format specifier will be replaced with
Zeros. Debugging Note : &pK prints only Zeros as address. If you need
actual address information, write 0 to kptr_restrict.
echo 0 > /proc/sys/kernel/kptr_restrict
[Found by poking around in a random vendor kernel tree, it would be nice
if someone would actually send these types of patches upstream - gkh]
Signed-off-by: Vamsi Krishna Samavedam <vskrishn@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8c06e407e ("usb: separate out sysdev pointer from
usb_bus") converted to use hcd->self.sysdev for DMA
operations instead of hcd->self.controller but forgot to do
it for one instance.
This gets caught when DMA debugging is enabled since dma map
and unmap end up using different device pointers.
Fix it.
Fixes: a8c06e407e ("usb: separate out sysdev pointer from usb_bus")
Reported-by: Carlos Hernandez <ceh@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using KASAN, Dmitry found a bug in the rh_call_control() routine: If
buffer allocation fails, the routine returns immediately without
unlinking its URB from the control endpoint, eventually leading to
linked-list corruption.
This patch fixes the problem by jumping to the end of the routine
(where the URB is unlinked) when an allocation failure occurs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Dmitry Vyukov <dvyukov@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For xhci-hcd platform device, all the DMA parameters are not
configured properly, notably dma ops for dwc3 devices.
The idea here is that you pass in the parent of_node along with
the child device pointer, so it would behave exactly like the
parent already does. The difference is that it also handles all
the other attributes besides the mask.
sysdev will represent the physical device, as seen from firmware
or bus.Splitting the usb_bus->controller field into the
Linux-internal device (used for the sysfs hierarchy, for printks
and for power management) and a new pointer (used for DMA,
DT enumeration and phy lookup) probably covers all that we really
need.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Tested-by: Baolin Wang <baolin.wang@linaro.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Tested-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Tested-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sinjan Kumar <sinjank@codeaurora.org>
Cc: David Fisher <david.fisher1@synopsys.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: "Thang Q. Nguyen" <tqnguyen@apm.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Dann Frazier <dann.frazier@canonical.com>
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Leo Li <pku.leo@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some platforms(e.g. rk3399 board), we can call hcd_add/remove
consecutively without calling usb_put_hcd/usb_create_hcd in between,
so hcd->flags can be stale.
If the HC dies due to whatever reason then without this patch we get
the below error on next hcd_add.
[173.296154] xhci-hcd xhci-hcd.2.auto: HC died; cleaning up
[173.296209] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[173.296762] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 6
[173.296931] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[173.297179] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003
[173.297203] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[173.297222] usb usb6: Product: xHCI Host Controller
[173.297240] usb usb6: Manufacturer: Linux 4.4.21 xhci-hcd
[173.297257] usb usb6: SerialNumber: xhci-hcd.2.auto
[173.298680] hub 6-0:1.0: USB hub found
[173.298749] hub 6-0:1.0: 1 port detected
[173.299382] rockchip-dwc3 usb@fe800000: USB HOST connected
[173.395418] hub 5-0:1.0: activate --> -19
[173.603447] irq 228: nobody cared (try booting with the "irqpoll" option)
[173.603493] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.4.21 #9
[173.603513] Hardware name: Google Kevin (DT)
[173.603531] Call trace:
[173.603568] [<ffffffc0002087dc>] dump_backtrace+0x0/0x160
[173.603596] [<ffffffc00020895c>] show_stack+0x20/0x28
[173.603623] [<ffffffc0004b28a8>] dump_stack+0x90/0xb0
[173.603650] [<ffffffc00027347c>] __report_bad_irq+0x48/0xe8
[173.603674] [<ffffffc0002737cc>] note_interrupt+0x1e8/0x28c
[173.603698] [<ffffffc000270a38>] handle_irq_event_percpu+0x1d4/0x25c
[173.603722] [<ffffffc000270b0c>] handle_irq_event+0x4c/0x7c
[173.603748] [<ffffffc00027456c>] handle_fasteoi_irq+0xb4/0x124
[173.603777] [<ffffffc00026fe3c>] generic_handle_irq+0x30/0x44
[173.603804] [<ffffffc0002701a8>] __handle_domain_irq+0x90/0xbc
[173.603827] [<ffffffc0002006f4>] gic_handle_irq+0xcc/0x188
...
[173.604500] [<ffffffc000203700>] el1_irq+0x80/0xf8
[173.604530] [<ffffffc000261388>] cpu_startup_entry+0x38/0x3cc
[173.604558] [<ffffffc00090f7d8>] rest_init+0x8c/0x94
[173.604585] [<ffffffc000e009ac>] start_kernel+0x3d0/0x3fc
[173.604607] [<0000000000b16000>] 0xb16000
[173.604622] handlers:
[173.604648] [<ffffffc000642084>] usb_hcd_irq
[173.604673] Disabling IRQ #228
Signed-off-by: William wu <wulf@rock-chips.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We get 1 warning when building kernel with W=1:
drivers/usb/core/hcd.c:2390:5: warning: no previous prototype for 'usb_bus_start_enum' [-Wmissing-prototypes]
In fact, these functions are declared in linux/usb/otg.h, so this patch
adds the missing header dependencies.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB core contains a bug that can show up when a USB-3 host
controller is removed. If the primary (USB-2) hcd structure is
released before the shared (USB-3) hcd, the core will try to do a
double-free of the common bandwidth_mutex.
The problem was described in graphical form by Chung-Geol Kim, who
first reported it:
=================================================
At *remove USB(3.0) Storage
sequence <1> --> <5> ((Problem Case))
=================================================
VOLD
------------------------------------|------------
(uevent)
________|_________
|<1> |
|dwc3_otg_sm_work |
|usb_put_hcd |
|peer_hcd(kref=2)|
|__________________|
________|_________
|<2> |
|New USB BUS #2 |
| |
|peer_hcd(kref=1) |
| |
--(Link)-bandXX_mutex|
| |__________________|
|
___________________ |
|<3> | |
|dwc3_otg_sm_work | |
|usb_put_hcd | |
|primary_hcd(kref=1)| |
|___________________| |
_________|_________ |
|<4> | |
|New USB BUS #1 | |
|hcd_release | |
|primary_hcd(kref=0)| |
| | |
|bandXX_mutex(free) |<-
|___________________|
(( VOLD ))
______|___________
|<5> |
| SCSI |
|usb_put_hcd |
|peer_hcd(kref=0) |
|*hcd_release |
|bandXX_mutex(free*)|<- double free
|__________________|
=================================================
This happens because hcd_release() frees the bandwidth_mutex whenever
it sees a primary hcd being released (which is not a very good idea
in any case), but in the course of releasing the primary hcd, it
changes the pointers in the shared hcd in such a way that the shared
hcd will appear to be primary when it gets released.
This patch fixes the problem by changing hcd_release() so that it
deallocates the bandwidth_mutex only when the _last_ hcd structure
referencing it is released. The patch also removes an unnecessary
test, so that when an hcd is released, both the shared_hcd and
primary_hcd pointers in the hcd's peer will be cleared.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Chung-Geol Kim <chunggeol.kim@samsung.com>
Tested-by: Chung-Geol Kim <chunggeol.kim@samsung.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the root hub device is added to the bus, it tries to get pins
information from pinctrl (see pinctrl_bind_pins, at really_probe), if
the pin information is described at DT, it will show below error since
the root hub's device node is the same with controller's, but controller's
pin has already been requested when it is added to platform bus.
imx6q-pinctrl 20e0000.iomuxc: pin MX6Q_PAD_GPIO_1 already
requested by 2184000.usb; cannot claim for usb1
imx6q-pinctrl 20e0000.iomuxc: pin-137 (usb1) status -22
imx6q-pinctrl 20e0000.iomuxc: could not request pin 137
(MX6Q_PAD_GPIO_1) from group usbotggrp-3 on device 20e0000.iomuxc
usb usb1: Error applying setting, reverse things back
To fix this issue, we move the root hub's device node assignment (equals
to contrller's) after device is added to bus, we only need to know root
hub's device node information after the device under root hub is created,
so this movement will not affect current function.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reported-by: Lars Steubesand <lars.steubesand@philips.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XHCI controller presents two USB buses to the system - one for USB2
and one for USB3. The hub init code (hub_port_init) is reentrant but
only locks one bus per thread, leading to a race condition failure when
two threads attempt to simultaneously initialise a USB2 and USB3 device:
[ 8.034843] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
[ 13.183701] usb 3-3: device descriptor read/all, error -110
On a test system this failure occurred on 6% of all boots.
The call traces at the point of failure are:
Call Trace:
[<ffffffff81b9bab7>] schedule+0x37/0x90
[<ffffffff817da7cd>] usb_kill_urb+0x8d/0xd0
[<ffffffff8111e5e0>] ? wake_up_atomic_t+0x30/0x30
[<ffffffff817dafbe>] usb_start_wait_urb+0xbe/0x150
[<ffffffff817db10c>] usb_control_msg+0xbc/0xf0
[<ffffffff817d07de>] hub_port_init+0x51e/0xb70
[<ffffffff817d4697>] hub_event+0x817/0x1570
[<ffffffff810f3e6f>] process_one_work+0x1ff/0x620
[<ffffffff810f3dcf>] ? process_one_work+0x15f/0x620
[<ffffffff810f4684>] worker_thread+0x64/0x4b0
[<ffffffff810f4620>] ? rescuer_thread+0x390/0x390
[<ffffffff810fa7f5>] kthread+0x105/0x120
[<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200
[<ffffffff81ba183f>] ret_from_fork+0x3f/0x70
[<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200
Call Trace:
[<ffffffff817fd36d>] xhci_setup_device+0x53d/0xa40
[<ffffffff817fd87e>] xhci_address_device+0xe/0x10
[<ffffffff817d047f>] hub_port_init+0x1bf/0xb70
[<ffffffff811247ed>] ? trace_hardirqs_on+0xd/0x10
[<ffffffff817d4697>] hub_event+0x817/0x1570
[<ffffffff810f3e6f>] process_one_work+0x1ff/0x620
[<ffffffff810f3dcf>] ? process_one_work+0x15f/0x620
[<ffffffff810f4684>] worker_thread+0x64/0x4b0
[<ffffffff810f4620>] ? rescuer_thread+0x390/0x390
[<ffffffff810fa7f5>] kthread+0x105/0x120
[<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200
[<ffffffff81ba183f>] ret_from_fork+0x3f/0x70
[<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200
Which results from the two call chains:
hub_port_init
usb_get_device_descriptor
usb_get_descriptor
usb_control_msg
usb_internal_control_msg
usb_start_wait_urb
usb_submit_urb / wait_for_completion_timeout / usb_kill_urb
hub_port_init
hub_set_address
xhci_address_device
xhci_setup_device
Mathias Nyman explains the current behaviour violates the XHCI spec:
hub_port_reset() will end up moving the corresponding xhci device slot
to default state.
As hub_port_reset() is called several times in hub_port_init() it
sounds reasonable that we could end up with two threads having their
xhci device slots in default state at the same time, which according to
xhci 4.5.3 specs still is a big no no:
"Note: Software shall not transition more than one Device Slot to the
Default State at a time"
So both threads fail at their next task after this.
One fails to read the descriptor, and the other fails addressing the
device.
Fix this in hub_port_init by locking the USB controller (instead of an
individual bus) to prevent simultaneous initialisation of both buses.
Fixes: 638139eb95 ("usb: hub: allow to process more usb hub events in parallel")
Link: https://lkml.org/lkml/2016/2/8/312
Link: https://lkml.org/lkml/2016/2/4/748
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some platforms don't have DMA, but we should still be able to build USB
drivers for these platforms. They could still be used through vhci_hcd,
usbip_host, or maybe something like USB passthrough in UML from a
capable host.
If NO_DMA=y:
ERROR: "dma_pool_destroy" [drivers/usb/core/usbcore.ko] undefined!
ERROR: "bad_dma_ops" [drivers/usb/core/usbcore.ko] undefined!
ERROR: "dma_pool_free" [drivers/usb/core/usbcore.ko] undefined!
ERROR: "dma_pool_alloc" [drivers/usb/core/usbcore.ko] undefined!
ERROR: "dma_pool_create" [drivers/usb/core/usbcore.ko] undefined!
Add a few checks for CONFIG_HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that usb_bus_list has been removed and switched to idr
rename the related mutex accordingly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB bus numbering is based on directly dealing with bitmaps and
defines a separate list of busses.
This can be simplified and unified by using existing idr functionality.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use bus_to_hcd() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb 3.1 extend the hub get-port-status request by adding different
request types. the new request types return 4 additional bytes called
extended port status, these bytes are returned after the regular
portstatus and portchange values.
The extended port status contains a speed ID for the currently used
sublink speed. A table of supported Speed IDs with details about the link
is provided by the hub in the device descriptor BOS SuperSpeedPlus
device capability Sublink Speed Attributes.
Support this new request. Ask for the extended port status after port
reset if hub supports USB 3.1. If link is running at SuperSpeedPlus
set the device speed to USB_SPEED_SUPER_PLUS
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A hcd roothub that supports HCD_USB31 is running at SuperSpeedPlus speed
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new USB_SPEED_SUPER_PLUS device speed, and make sure usb core can
handle the new speed.
In most cases the behaviour is the same as with USB_SPEED_SUPER SuperSpeed
devices. In a few places we add a "Plus" string to inform the user of the
new speed.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_mon_operations structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare numbers to set the 'bDescriptorType' descriptor fields
while the values are #define'd in <linux/usb/ch9.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hosts that support USB 3.1 Enhaned SuperSpeed can set their speed to
HCD_USB31 to let usb core and host drivers know that the controller
supports new USB 3.1 features.
make sure usb core handle HCD_USB31 hosts correctly, for now similar
to HCD_USB3.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With this patch a flag instead of a variable
is used for the default device authorization.
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interfaces are allowed per default.
This can disabled or enabled (again) by writing 0 or 1 to
/sys/bus/usb/devices/usbX/interface_authorized_default
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 1d958bef45 as the
signed-off-by address is invalid.
Cc: Stefan Koch <stefan.koch10@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 3cf1fc8065 as the
signed-off-by address is invalid.
Cc: Stefan Koch <stefan.koch10@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With this patch a flag instead of a variable
is used for the default device authorization.
Signed-off-by: Stefan Koch <skoch@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interfaces are allowed per default.
This can disabled or enabled (again) by writing 0 or 1 to
/sys/bus/usb/devices/usbX/interface_authorized_default
Signed-off-by: Stefan Koch <skoch@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix four occurrences of checkpatch.pl error:
ERROR: do not use assignment in if condition
The semantic patch that makes this change is:
// <smpl>
@@
identifier i;
expression E;
statement S;
constant c;
binary operator b;
@@
+ i = E;
if (
- (i = E)
+ i
b
c ) S
@@
identifier i, i2;
expression E1, E2;
constant c;
@@
+ if( E1->i ) {
+ i2 = E2;
+ if (i2 < c) {
- if( E1->i && (i2 = E2) < c ) {
...
- }
+ }
+ }
// </smpl>
Signed-off-by: Kris Borer <kborer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>