Fix to return -ENOMEM in the ipw_rx_queue_alloc() error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_tx_txqaddbuf assumes that all the linked buffers in the queue passed
to it are part of the same A-MPDU or MPDU. The CAB queue rework violates
this assumption, which can cause the internal queue depth to go
negative.
Fix this by increasing the counter for all slots of [bf, bf->bf_lastbf]
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This provides some of the same info found in
the ath9k_htc debugfs through the standard ethtool stats API.
This logic is only supported when ath9k_htc debugfs kernel
feature is enabled, since that is the only time stats
are actually gathered.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After receiving channel switch announcement from AP, scan and
association on that channel is blocked for DFS_CHAN_MOVE_TIME
(10 seconds). Hence station will be able to connect to the AP,
once it is moved to new channel.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds code to parse requested AP's 11h capabilities
and add 11h information in association request.
Also, deauth is sent to the AP after receiving channel switch
announcement event from firmware. This happens when AP advertises
WLAN_EID_CHANNEL_SWITCH IE in it's beacon.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not unconditionally access the chan variable in
brcmf_cfg80211_mgmt_tx() as it may be NULL.
Use freq instead.
Introduced by c2ff8cad64
("brcm80211: make mgmt_tx in brcmfmac accept a NULL channel")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use negative check (if(!bss_desc)) and return failure
instead of failing a NULL check later in
mwifiex_check_network_compatibility() routine.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A typo causes routine rtl92cu_phy_rf6052_set_cck_txpower() to test the
same condition twice. The problem was found using cppcheck-1.49, and the
proper fix was verified against the pre-mac80211 version of the code.
This patch was originally included as commit 1288aa4, but was accidentally
reverted in a later patch.
Reported-by: David Binderman <dcb314@hotmail.com> [original report]
Reported-by: Andrea Morello <andrea.merello@gmail.com> [report of accidental reversion]
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable <stable@vger.kernel.org> [back to 2.6.39]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add scatter gather list support for better rx glom performance.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introducing a new SDIO block data access interface function
brcmf_sdio_buffrw. It will act as a unified interface function for any block
data access to WiFi dongle through SDIO interface. This patch enables
the support for single skb transmission.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is an ID table registered to SDIO stack which consists of all SDIO devices
supported by brcmfmac. It is not necessary to have an extra check.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of allocating an empty list item and queue that for
the dpc data worker to dequeue an atomic counter is used.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just cleaning up and being consistent in naming operations
related to struct brcmf_fws_mac_descriptor objects.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware-signalling code used NL80211_NUM_ACS, but it has
its own definition enum brcmf_fws_fifo, which is more appropriate
to use. This effectively removes the need to include nl80211.h.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The term prec (precedence) is different from the fifo number. Rename
use of prec with fifo to be consistent and clear.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware will sent an event message when bc/mc traffic should
be sent to the device using credit mechanism.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This should be >= ARRAY_SIZE() instead of > ARRAY_SIZE().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CUS198 and CUS230 are similar cards, both
are AR9485 + xLNA solutions. But, the subsystem IDs
differ - identify CUS230 explicitly to make things
clearer.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the REGULATORY debug level to print the target power
details. EEPROM can be used for other purposes and this
spams the log.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a new device for this driver.
Reported-by: Tobias Kluge <zielscheibe@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Tobias Kluge <zielscheibe@gmail.com>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: Fix ANI monitoring" reverted an earlier
commit that adjusted ANI to improve performance. But, this causes
adverse effects in AP mode (as reported by Felix based on an OpenWrt
report). Use the older INI/period configuration for now until more
testing is done.
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: Add custom parameters for CUS198" didn't
pass the correct gpio value to ath9k_hw_cfg_output(). Fix it.
Reported-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When trying to unset a previously-set multicast list (i.e. the new list
has 0 entries), mwifiex_set_multicast_list() was calling down to
mwifiex_request_set_multicast_list() while leaving
mcast_list.num_multicast_addr as an uninitialized value.
We were arriving at mwifiex_cmd_mac_multicast_adr() which would then
proceed to do an often huge memcpy of
mcast_list.num_multicast_addr*ETH_ALEN bytes, causing memory corruption
and hard to debug crashes.
Fix this by setting mcast_list.num_multicast_addr to 0 when no multicast
list is provided. Similarly, fix up the logic in
mwifiex_request_set_multicast_list() to unset the multicast list that
was previously sent to the hardware in such cases.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow a regulatory domain country code to be specified at boot
using a module argument. This overrides the firmware regulatory
mode.
This patch also enables uAP to operate in 11a mode with hostapd.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make the commenting style consistent with networking block comment
style as suggested by checkpatch.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Removing some boilerplate by using module_spi_driver instead of calling
register and unregister in the otherwise empty init/exit functions
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The fw_status wasn't zeroed during allocation, resulting
in uninitialized var usage, and finally causing AP
traffic stop after recovery.
The wrong value in fw_status_2->counters.tx_lnk_free_pkts
led to a bad lnk->allocated_pkts calculation in
wlcore_fw_status(), causing wl18xx_lnk_low_prio() to return
FALSE (lnk->allocated_pkts > thold).
This eventually blocked the link in wlcore_tx_work_locked(),
as wl1271_skb_dequeue() continuously returned NULL.
Fix it by zeroing wl->fw_status_1/2 during allocation.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Otherwise, if the work is pending, we might get
a bad dereference after the interface is removed.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When associating to an AP with WEP set the
default key upon association by implementing
the set_deafult_key_idx op.
Fixes auto-arp sent with wrong key_idx bug.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In some R&D chips, the device may be left untrimmed and with the MAC
address missing from fuse ROM. In order to support those devices,
apply a random locally administered MAC address instead.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The current code configures the peer caps only on BSS_CHANGED_HT
notification. However, we have to configure the peer caps
(and rates) even when HT is not enabled. Otherwise, the fw
continues working with low rates.
Configure the peer caps when sta_exists is true (i.e. when
we extracted the sta rates, e.g. on association).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Instead of doing all the sysfs file handling in the main file, move it
to a new sysfs source file to reduce the amount of code in a single
file.
Signed-off-by: Luciano Coelho <coelho@ti.com>
In PG2.0 there is an issue where PHY's FDSP Code RAM sometimes gets
corrupted when exiting from ELP mode. This issue is related to FDSP
Code RAM clock implementation.
PG2.1 introduces a HW fix for this issue that requires the driver to
change the FDSP Code Ram clock settings (mux it to ATGP clock instead
of its own clock).
This workaround uses PHY_FPGA_SPARE_1 register and is relevant to WL8
PG2.1 devices.
The fix is also backward compatible with older PG2.0 devices where the
register PHY_FPGA_SPARE_1 is not used and not connected.
The fix is done in the wl18xx_pre_upload function (must be performed
before uploading the FW code) and includes the following steps:
1. Disable FDSP clock
2. Set ATPG clock toward FDSP Code RAM rather than its own clock.
3. Re-enable FDSP clock
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
If "device is disconnected" check occurs to be true in ezusb_access_ltv(),
it just return -ENODEV. But that means request_context is leaked since
there are no any references to it anymore.
The patch adds a call to ezusb_request_context_put() before return.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CUS198 is a card based on AR9485. There are differences
between the base reference design HB125 and CUS198.
Identify such cards based on the PCI subsystem IDs and
set HW parameters appropriately.
Addresses this bug - https://bugzilla.kernel.org/show_bug.cgi?id=49201
Cc: jkp@iki.fi
Cc: gfmichaud@gmail.com
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wei Yongjun