Currently, espintcp_rcv drops packets silently, which makes debugging
issues difficult. Count packets as either XfrmInHdrError (when the
packet was too short or contained invalid data) or XfrmInError (for
other issues).
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Currently, short messages (less than 4 bytes after the length header)
will break the stream of messages. This is unnecessary, since we can
still parse messages even if they're too short to contain any usable
data. This is also bogus, as keepalive messages (a single 0xff byte),
though not needed with TCP encapsulation, should be allowed.
This patch changes the stream parser so that short messages are
accepted and dropped in the kernel. Messages that contain a valid SPI
or non-ESP header are processed as before.
Fixes: e27cca96cd ("xfrm: add espintcp (RFC 8229)")
Reported-by: Andrew Cagney <cagney@libreswan.org>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch fixes:
commit b9aaec8f0b ("fib: use indirect call wrappers in the most common
fib_rules_ops") which didn't consider the case when
CONFIG_IPV6_MULTIPLE_TABLES is not set.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: b9aaec8f0b ("fib: use indirect call wrappers in the most common fib_rules_ops")
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the first one in particular has been quite noisy ("broke" in -rc5)
so this would be worth landing even this late even if users likely
won't see a difference
-----BEGIN PGP SIGNATURE-----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=kJqr
-----END PGP SIGNATURE-----
Merge tag '9p-for-5.8-2' of git://github.com/martinetd/linux into master
Pull 9p fixes from Dominique Martinet:
"A couple of syzcaller fixes for 5.8
The first one in particular has been quite noisy ("broke" in -rc5) so
this would be worth landing even this late even if users likely won't
see a difference"
* tag '9p-for-5.8-2' of git://github.com/martinetd/linux:
9p/trans_fd: Fix concurrency del of req_list in p9_fd_cancelled/p9_read_work
net/9p: validate fds in p9_fd_open
Cited commit mistakenly removed the trap group for externally routed
packets (e.g., via the management interface) and grouped locally routed
and externally routed packet traps under the same group, thereby
subjecting them to the same policer.
This can result in problems, for example, when FRR is restarted and
suddenly all transient traffic is trapped to the CPU because of a
default route through the management interface. Locally routed packets
required to re-establish a BGP connection will never reach the CPU and
the routing tables will not be re-populated.
Fix this by using a different trap group for externally routed packets.
Fixes: 8110668ecd ("mlxsw: spectrum_trap: Register layer 3 control traps")
Reported-by: Alex Veber <alexve@mellanox.com>
Tested-by: Alex Veber <alexve@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_trie_unmerge() is called with RTNL held, but not from an RCU
read-side critical section. This leads to the following warning [1] when
the FIB alias list in a leaf is traversed with
hlist_for_each_entry_rcu().
Since the function is always called with RTNL held and since
modification of the list is protected by RTNL, simply use
hlist_for_each_entry() and silence the warning.
[1]
WARNING: suspicious RCU usage
5.8.0-rc4-custom-01520-gc1f937f3f83b #30 Not tainted
-----------------------------
net/ipv4/fib_trie.c:1867 RCU-list traversed in non-reader section!!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
1 lock held by ip/164:
#0: ffffffff85a27850 (rtnl_mutex){+.+.}-{3:3}, at: rtnetlink_rcv_msg+0x49a/0xbd0
stack backtrace:
CPU: 0 PID: 164 Comm: ip Not tainted 5.8.0-rc4-custom-01520-gc1f937f3f83b #30
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-2.fc32 04/01/2014
Call Trace:
dump_stack+0x100/0x184
lockdep_rcu_suspicious+0x153/0x15d
fib_trie_unmerge+0x608/0xdb0
fib_unmerge+0x44/0x360
fib4_rule_configure+0xc8/0xad0
fib_nl_newrule+0x37a/0x1dd0
rtnetlink_rcv_msg+0x4f7/0xbd0
netlink_rcv_skb+0x17a/0x480
rtnetlink_rcv+0x22/0x30
netlink_unicast+0x5ae/0x890
netlink_sendmsg+0x98a/0xf40
____sys_sendmsg+0x879/0xa00
___sys_sendmsg+0x122/0x190
__sys_sendmsg+0x103/0x1d0
__x64_sys_sendmsg+0x7d/0xb0
do_syscall_64+0x54/0xa0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7fc80a234e97
Code: Bad RIP value.
RSP: 002b:00007ffef8b66798 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007fc80a234e97
RDX: 0000000000000000 RSI: 00007ffef8b66800 RDI: 0000000000000003
RBP: 000000005f141b1c R08: 0000000000000001 R09: 0000000000000000
R10: 00007fc80a2a8ac0 R11: 0000000000000246 R12: 0000000000000001
R13: 0000000000000000 R14: 00007ffef8b67008 R15: 0000556fccb10020
Fixes: 0ddcf43d5d ("ipv4: FIB Local/MAIN table collapse")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
A sequence counter write side critical section must be protected by some
form of locking to serialize writers. If the serialization primitive is
not disabling preemption implicitly, preemption has to be explicitly
disabled before entering the sequence counter write side critical
section.
A plain seqcount_t does not contain the information of which lock must
be held when entering a write side critical section.
Use the new seqcount_spinlock_t and seqcount_mutex_t data types instead,
which allow to associate a lock with the sequence counter. This enables
lockdep to verify that the lock used for writer serialization is held
when the write side critical section is entered.
If lockdep is disabled this lock association is compiled out and has
neither storage size nor runtime overhead.
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200720155530.1173732-17-a.darwish@linutronix.de
A sequence counter write side critical section must be protected by some
form of locking to serialize writers. A plain seqcount_t does not
contain the information of which lock must be held when entering a write
side critical section.
Use the new seqcount_rwlock_t data type, which allows to associate a
rwlock with the sequence counter. This enables lockdep to verify that
the rwlock used for writer serialization is held when the write side
critical section is entered.
If lockdep is disabled this lock association is compiled out and has
neither storage size nor runtime overhead.
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200720155530.1173732-16-a.darwish@linutronix.de
A sequence counter write side critical section must be protected by some
form of locking to serialize writers. A plain seqcount_t does not
contain the information of which lock must be held when entering a write
side critical section.
Use the new seqcount_spinlock_t data type, which allows to associate a
spinlock with the sequence counter. This enables lockdep to verify that
the spinlock used for writer serialization is held when the write side
critical section is entered.
If lockdep is disabled this lock association is compiled out and has
neither storage size nor runtime overhead.
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200720155530.1173732-15-a.darwish@linutronix.de
This avoids another inderect call per RX packet which save us around
20-40 ns.
Changelog:
v1 -> v2:
- Move declaraions to fib_rules.h to remove warnings
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When red_init() fails, red_destroy() is called to clean up.
If the timer is not initialized yet, del_timer_sync() will
complain. So we have to move timer_setup() before any failure.
Reported-and-tested-by: syzbot+6e95a4fabf88dc217145@syzkaller.appspotmail.com
Fixes: aee9caa03f ("net: sched: sch_red: Add qevents "early_drop" and "mark"")
Cc: Petr Machata <petrm@mellanox.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_route_info_create() invokes nexthop_get(), which increases the
refcount of the "nh".
When ip6_route_info_create() returns, local variable "nh" becomes
invalid, so the refcount should be decreased to keep refcount balanced.
The reference counting issue happens in one exception handling path of
ip6_route_info_create(). When nexthops can not be used with source
routing, the function forgets to decrease the refcnt increased by
nexthop_get(), causing a refcnt leak.
Fix this issue by pulling up the error source routing handling when
nexthops can not be used with source routing.
Fixes: f88d8ea67f ("ipv6: Plumb support for nexthop object in a fib6_info")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MPTCP socket's write_seq member can be read without the msk lock
held, so use WRITE_ONCE() to store it.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MPTCP socket's write_seq member should be read with READ_ONCE() when
the msk lock is not held.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bare TCP ack skbs are freed right after MPTCP sees them, so the work to
allocate, zero, and populate the MPTCP skb extension is wasted. Detect
these skbs and do not add skb extensions to them.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MPTCP state machine handles disconnections on non-fallback connections,
but the mptcp_sock still needs to get notified when fallback subflows
disconnect.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 8684 appendix D describes the connection state machine for
MPTCP. This patch implements the DATA_FIN / DATA_ACK exchanges and
MPTCP-level socket state changes described in that appendix, rather than
simply sending DATA_FIN along with TCP FIN when disconnecting subflows.
DATA_FIN is now sent and acknowledged before shutting down the
subflows. Received DATA_FIN information (if not part of a data packet)
is written to the MPTCP socket when the incoming DSS option is parsed by
the subflow, and the MPTCP worker is scheduled to process the
flag. DATA_FIN received as part of a full DSS mapping will be handled
when the mapping is processed.
The DATA_FIN is acknowledged by the worker if the reader is caught
up. If there is still data to be moved to the MPTCP-level queue, ack_seq
will be incremented to account for the DATA_FIN when it reaches the end
of the stream and a DATA_ACK will be sent to the peer.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After DATA_FIN has been sent, the peer will acknowledge it. An ack of
the relevant MPTCP-level sequence number will update the MPTCP
connection state appropriately.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be used to transition to the appropriate state on close and
determine if a DATA_FIN needs to be sent for that state transition.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Incoming DATA_FIN headers need to propagate the presence of the DATA_FIN
bit and the associated sequence number to the MPTCP layer, even when
arriving on a bare ACK that does not get added to the receive queue. Add
structure members to store the DATA_FIN information and helpers to set
and check those values.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since DATA_FIN information is the same for every subflow, store it only
in the mptcp_sock.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mptcp_close() acquires the msk lock, so it clearly should not be held
before the function is called.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A MPTCP socket where sending has been shut down should not attempt to
send additional data, since DATA_FIN has already been sent.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 8684-compliant DATA_FIN needs to be sent and ack'd before subflows
are closed with TCP FIN, so write DATA_FIN DSS headers whenever their
transmission has been enabled by the MPTCP connection-level socket.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure not just the pointer itself but the whole range lies in
the user address space. For that pass the length and then use
the access_ok helper to do the check.
Fixes: 6d04fe15f7 ("net: optimize the sockptr_t for unified kernel/user address spaces")
Reported-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
sockptr_advance never properly worked. Replace it with _offset variants
of copy_from_sockptr and copy_to_sockptr.
Fixes: ba423fdaa5 ("net: add a new sockptr_t type")
Reported-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reported-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jason A. Donenfeld <Jason@zx2c4.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was accidentally removed in an unrelated commit.
Fixes: c2f12630c6 ("netfilter: switch nf_setsockopt to sockptr_t")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there's a core tracepoint that reports these events, there's
no need to maintain dprintk() call sites in each arm of the switch
statements.
We also refresh the documenting comments.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Jason tells me that a ULP cannot rely on getting an ESTABLISHED
and DISCONNECTED event pair for each connection, so transport
reference counting in the CM event handler will never be reliable.
Now that we have ib_drain_qp(), svcrdma should no longer need to
hold transport references while Sends and Receives are posted. So
remove the get/put call sites in the CM event handlers.
This eliminates a significant source of locked memory bus traffic.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
During a connection tear down, the Receive queue is flushed before
the device resources are freed. Typically, all the Receives flush
with IB_WR_FLUSH_ERR.
However, any pending successful Receives flush with IB_WR_SUCCESS,
and the server automatically posts a fresh Receive to replace the
completing one. This happens even after the connection has closed
and the RQ is drained. Receives that are posted after the RQ is
drained appear never to complete, causing a Receive resource leak.
The leaked Receive buffer is left DMA-mapped.
To prevent these late-posted recv_ctxt's from leaking, block new
Receive posting after XPT_CLOSE is set.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
xsk_getsockopt() is copying uninitialized stack memory to userspace when
'extra_stats' is 'false'. Fix it. Doing '= {};' is sufficient since currently
'struct xdp_statistics' is defined as follows:
struct xdp_statistics {
__u64 rx_dropped;
__u64 rx_invalid_descs;
__u64 tx_invalid_descs;
__u64 rx_ring_full;
__u64 rx_fill_ring_empty_descs;
__u64 tx_ring_empty_descs;
};
When being copied to the userspace, 'stats' will not contain any uninitialized
'holes' between struct fields.
Fixes: 8aa5a33578 ("xsk: Add new statistics")
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/bpf/20200728053604.404631-1-yepeilin.cs@gmail.com
The original return is NOTIFY_STOP, but notifier_call_chain would stop
the future call for register_pm_notifier even registered on other Kernel
modules with the same priority which value is zero.
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For some reason they tend to squat on the very first CSR/
Cambridge Silicon Radio VID/PID instead of paying fees.
This is an extremely common problem; the issue goes as back as 2013
and these devices are only getting more popular, even rebranded by
reputable vendors and sold by retailers everywhere.
So, at this point in time there are hundreds of modern dongles reusing
the ID of what originally was an early Bluetooth 1.1 controller.
Linux is the only place where they don't work due to spotty checks
in our detection code. It only covered a minimum subset.
So what's the big idea? Take advantage of the fact that all CSR
chips report the same internal version as both the LMP sub-version and
HCI revision number. It always matches, couple that with the manufacturer
code, that rarely lies, and we now have a good idea of who is who.
Additionally, by compiling a list of user-reported HCI/lsusb dumps, and
searching around for legit CSR dongles in similar product ranges we can
find what CSR BlueCore firmware supported which Bluetooth versions.
That way we can narrow down ranges of fakes for each of them.
e.g. Real CSR dongles with LMP subversion 0x73 are old enough that
support BT 1.1 only; so it's a dead giveaway when some
third-party BT 4.0 dongle reuses it.
So, to sum things up; there are multiple classes of fake controllers
reusing the same 0A12:0001 VID/PID. This has been broken for a while.
Known 'fake' bcdDevices: 0x0100, 0x0134, 0x1915, 0x2520, 0x7558, 0x8891
IC markings on 0x7558: FR3191AHAL 749H15143 (???)
https://bugzilla.kernel.org/show_bug.cgi?id=60824
Fixes: 81cac64ba2 (Deal with USB devices that are faking CSR vendor)
Reported-by: Michał Wiśniewski <brylozketrzyn@gmail.com>
Tested-by: Mike Johnson <yuyuyak@gmail.com>
Tested-by: Ricardo Rodrigues <ekatonb@gmail.com>
Tested-by: M.Hanny Sabbagh <mhsabbagh@outlook.com>
Tested-by: Oussama BEN BRAHIM <b.brahim.oussama@gmail.com>
Tested-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
commit 17175d1a27 ("xfrm: esp6: fix encapsulation header offset
computation") changed esp6_input_done2 to correctly find the size of
the IPv6 header that precedes the TCP/UDP encapsulation header, but
didn't adjust the final call to skb_set_transport_header, which I
assumed was correct in using skb_network_header_len.
Xiumei Mu reported that when we create xfrm states that include port
numbers in the selector, traffic from the user sockets is dropped. It
turns out that we get a state mismatch in __xfrm_policy_check, because
we end up trying to compare the encapsulation header's ports with the
selector that's based on user traffic ports.
Fixes: 0146dca70b ("xfrm: add support for UDPv6 encapsulation of ESP")
Fixes: 26333c37fc ("xfrm: add IPv6 support for espintcp")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
commit 547ce4cfb3 ("switch cmsghdr_from_user_compat_to_kern() to
copy_from_user()") missed one of the places where ucmlen should've been
replaced with cmsg.cmsg_len, now that we are fetching the entire struct
rather than doing it field-by-field.
As the result, compat sendmsg() with several different-sized cmsg
attached started to fail with EINVAL. Trivial to fix, fortunately.
Fixes: 547ce4cfb3 ("switch cmsghdr_from_user_compat_to_kern() to copy_from_user()")
Reported-by: Nick Bowler <nbowler@draconx.ca>
Tested-by: Nick Bowler <nbowler@draconx.ca>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print PRP specific information from node table as part of debugfs
node table display. Also display the node as DAN-H or DAN-P depending
on the info from node table.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DAN-P (Dual Attached Nodes PRP) nodes are expected to receive
traditional IP packets as well as PRP (Parallel Redundancy
Protocol) tagged (trailer) packets. PRP trailer is 6 bytes
of PRP protocol unit called RCT, Redundancy Control Trailer
(RCT) similar to HSR tag. PRP network can have traditional
devices such as bridges/switches or PC attached to it and
should be able to communicate. Regular Ethernet devices treat
the RCT as pads. This patch adds logic to format L2 frames
from network stack to add a trailer (RCT) and send it as
duplicates over the slave interfaces when the protocol is
PRP as per IEC 62439-3. At the ingress, it strips the trailer,
do duplicate detection and rejection and forward a stripped
frame up the network stack. PRP device should accept frames
from Singly Attached Nodes (SAN) and thus the driver mark
the link where the frame came from in the node table.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparatory patch to introduce PRP, refactor the code specific to
handling HSR frames into separate functions and call them through
proto_ops function pointers.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for generation of PRP supervision frames. For PRP,
supervision frame format is similar to HSR version 0, but have
a PRP Redundancy Control Trailer (RCT) added and uses a different
message type, PRP_TLV_LIFE_CHECK_DD. Also update
is_supervision_frame() to include the new message type used for
PRP supervision frame.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparatory patch to introduce support for PRP protocol, add a
protocol ops ptr in the private hsr structure to hold function
pointers as some of the functions at protocol level packet
handling is different for HSR vs PRP. It is expected that PRP will
add its of set of functions for protocol handling. Modify existing
hsr_announce() function to call proto_ops->send_sv_frame() to send
supervision frame for HSR. This is expected to be different for PRP.
So introduce a ops function ptr, send_sv_frame() for the same and
initialize it to send_hsr_supervsion_frame(). Modify hsr_announce()
to call proto_ops->send_sv_frame().
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparatory patch to introduce PRP protocol support in the
driver, refactor the skb init code to a separate function.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parallel Redundancy Protocol (PRP) is another redundancy protocol
introduced by IEC 63439 standard. It is similar to HSR in many
aspects:-
- Use a pair of Ethernet interfaces to created the PRP device
- Use a 6 byte redundancy protocol part (RCT, Redundancy Check
Trailer) similar to HSR Tag.
- Has Link Redundancy Entity (LRE) that works with RCT to implement
redundancy.
Key difference is that the protocol unit is a trailer instead of a
prefix as in HSR. That makes it inter-operable with tradition network
components such as bridges/switches which treat it as pad bytes,
whereas HSR nodes requires some kind of translators (Called redbox) to
talk to regular network devices. This features allows regular linux box
to be converted to a DAN-P box. DAN-P stands for Dual Attached Node - PRP
similar to DAN-H (Dual Attached Node - HSR).
Add a comment at the header/source code to explicitly state that the
driver files also handles PRP protocol as well.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unblocking sockets used for outgoing connections were not containing
inet info about the initial connection due to a typo there: the value of
"err" variable is negative in the kernelspace.
This fixes the creation of additional subflows where the remote port has
to be reused if the other host didn't announce another one. This also
fixes inet_diag showing blank info about MPTCP sockets from unblocking
sockets doing a connect().
Fixes: 41be81a8d3 ("mptcp: fix unblocking connect()")
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MPLS has no dependency with the device type of underlying devices.
Hence the device type check to add mpls support for devices can be
avoided.
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cited commit mistakenly copied provided option to 'val' instead of to
'mfc':
```
- if (copy_from_user(&mfc, optval, sizeof(mfc))) {
+ if (copy_from_sockptr(&val, optval, sizeof(val))) {
```
Fix this by copying the option to 'mfc'.
selftest router_multicast.sh before:
$ ./router_multicast.sh
smcroutectl: Unknown or malformed IPC message 'a' from client.
smcroutectl: failed removing multicast route, does not exist.
TEST: mcast IPv4 [FAIL]
Multicast not received on first host
TEST: mcast IPv6 [ OK ]
smcroutectl: Unknown or malformed IPC message 'a' from client.
smcroutectl: failed removing multicast route, does not exist.
TEST: RPF IPv4 [FAIL]
Multicast not received on first host
TEST: RPF IPv6 [ OK ]
selftest router_multicast.sh after:
$ ./router_multicast.sh
TEST: mcast IPv4 [ OK ]
TEST: mcast IPv6 [ OK ]
TEST: RPF IPv4 [ OK ]
TEST: RPF IPv6 [ OK ]
Fixes: 01ccb5b48f ("net/ipv4: switch ip_mroute_setsockopt to sockptr_t")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the maximum dmb buffer limit for an ism device is reached no more
dmb buffers can be registered. When this happens the reason code is set
to SMC_CLC_DECL_MEM indicating out-of-memory. This is the same reason
code that is used when no memory could be allocated for the new dmb
buffer.
This is confusing for users when they see this error but there is more
memory available. To solve this set a separate new reason code when the
maximum dmb limit exceeded.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that BPF program/link management is centralized in generic net_device
code, kernel code never queries program id from drivers, so
XDP_QUERY_PROG/XDP_QUERY_PROG_HW commands are unnecessary.
This patch removes all the implementations of those commands in kernel, along
the xdp_attachment_query().
This patch was compile-tested on allyesconfig.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200722064603.3350758-10-andriin@fb.com
Add support for LINK_UPDATE command for BPF XDP link to enable reliable
replacement of underlying BPF program.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200722064603.3350758-6-andriin@fb.com
Add bpf_link-based API (bpf_xdp_link) to attach BPF XDP program through
BPF_LINK_CREATE command.
bpf_xdp_link is mutually exclusive with direct BPF program attachment,
previous BPF program should be detached prior to attempting to create a new
bpf_xdp_link attachment (for a given XDP mode). Once BPF link is attached, it
can't be replaced by other BPF program attachment or link attachment. It will
be detached only when the last BPF link FD is closed.
bpf_xdp_link will be auto-detached when net_device is shutdown, similarly to
how other BPF links behave (cgroup, flow_dissector). At that point bpf_link
will become defunct, but won't be destroyed until last FD is closed.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200722064603.3350758-5-andriin@fb.com
Further refactor XDP attachment code. dev_change_xdp_fd() is split into two
parts: getting bpf_progs from FDs and attachment logic, working with
bpf_progs. This makes attachment logic a bit more straightforward and
prepares code for bpf_xdp_link inclusion, which will share the common logic.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200722064603.3350758-4-andriin@fb.com
Instead of delegating to drivers, maintain information about which BPF
programs are attached in which XDP modes (generic/skb, driver, or hardware)
locally in net_device. This effectively obsoletes XDP_QUERY_PROG command.
Such re-organization simplifies existing code already. But it also allows to
further add bpf_link-based XDP attachments without drivers having to know
about any of this at all, which seems like a good setup.
XDP_SETUP_PROG/XDP_SETUP_PROG_HW are just low-level commands to driver to
install/uninstall active BPF program. All the higher-level concerns about
prog/link interaction will be contained within generic driver-agnostic logic.
All the XDP_QUERY_PROG calls to driver in dev_xdp_uninstall() were removed.
It's not clear for me why dev_xdp_uninstall() were passing previous prog_flags
when resetting installed programs. That seems unnecessary, plus most drivers
don't populate prog_flags anyways. Having XDP_SETUP_PROG vs XDP_SETUP_PROG_HW
should be enough of an indicator of what is required of driver to correctly
reset active BPF program. dev_xdp_uninstall() is also generalized as an
iteration over all three supported mode.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200722064603.3350758-3-andriin@fb.com
The bpf iterator for bpf sock local storage map
is implemented. User space interacts with sock
local storage map with fd as a key and storage value.
In kernel, passing fd to the bpf program does not
really make sense. In this case, the sock itself is
passed to bpf program.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200723184116.590602-1-yhs@fb.com
This patch refactored target bpf_iter_init_seq_priv_t callback
function to accept additional information. This will be needed
in later patches for map element targets since a particular
map should be passed to traverse elements for that particular
map. In the future, other information may be passed to target
as well, e.g., pid, cgroup id, etc. to customize the iterator.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200723184110.590156-1-yhs@fb.com
There is no functionality change for this patch.
Struct bpf_iter_reg is used to register a bpf_iter target,
which includes information for both prog_load, link_create
and seq_file creation.
This patch puts fields related seq_file creation into
a different structure. This will be useful for map
elements iterator where one iterator covers different
map types and different map types may have different
seq_ops, init/fini private_data function and
private_data size.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200723184109.590030-1-yhs@fb.com
When BPF socket lookup prog selects a socket that belongs to a reuseport
group, and the reuseport group has connected sockets in it, the socket
selected by reuseport will be discarded, and socket returned by BPF socket
lookup will be used instead.
Modify this behavior so that the socket selected by reuseport running after
BPF socket lookup always gets used. Ignore the fact that the reuseport
group might have connections because it is only relevant when scoring
sockets during regular hashtable-based lookup.
Fixes: 72f7e9440e ("udp: Run SK_LOOKUP BPF program on socket lookup")
Fixes: 6d4201b138 ("udp6: Run SK_LOOKUP BPF program on socket lookup")
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Link: https://lore.kernel.org/bpf/20200722161720.940831-2-jakub@cloudflare.com
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix RCU locaking in iwlwifi, from Johannes Berg.
2) mt76 can access uninitialized NAPI struct, from Felix Fietkau.
3) Fix race in updating pause settings in bnxt_en, from Vasundhara
Volam.
4) Propagate error return properly during unbind failures in ax88172a,
from George Kennedy.
5) Fix memleak in adf7242_probe, from Liu Jian.
6) smc_drv_probe() can leak, from Wang Hai.
7) Don't muck with the carrier state if register_netdevice() fails in
the bonding driver, from Taehee Yoo.
8) Fix memleak in dpaa_eth_probe, from Liu Jian.
9) Need to check skb_put_padto() return value in hsr_fill_tag(), from
Murali Karicheri.
10) Don't lose ionic RSS hash settings across FW update, from Shannon
Nelson.
11) Fix clobbered SKB control block in act_ct, from Wen Xu.
12) Missing newlink in "tx_timeout" sysfs output, from Xiongfeng Wang.
13) IS_UDPLITE cleanup a long time ago, incorrectly handled
transformations involving UDPLITE_RECV_CC. From Miaohe Lin.
14) Unbalanced locking in netdevsim, from Taehee Yoo.
15) Suppress false-positive error messages in qed driver, from Alexander
Lobakin.
16) Out of bounds read in ax25_connect and ax25_sendmsg, from Peilin Ye.
17) Missing SKB release in cxgb4's uld_send(), from Navid Emamdoost.
18) Uninitialized value in geneve_changelink(), from Cong Wang.
19) Fix deadlock in xen-netfront, from Andera Righi.
19) flush_backlog() frees skbs with IRQs disabled, so should use
dev_kfree_skb_irq() instead of kfree_skb(). From Subash Abhinov
Kasiviswanathan.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (111 commits)
drivers/net/wan: lapb: Corrected the usage of skb_cow
dev: Defer free of skbs in flush_backlog
qrtr: orphan socket in qrtr_release()
xen-netfront: fix potential deadlock in xennet_remove()
flow_offload: Move rhashtable inclusion to the source file
geneve: fix an uninitialized value in geneve_changelink()
bonding: check return value of register_netdevice() in bond_newlink()
tcp: allow at most one TLP probe per flight
AX.25: Prevent integer overflows in connect and sendmsg
cxgb4: add missing release on skb in uld_send()
net: atlantic: fix PTP on AQC10X
AX.25: Prevent out-of-bounds read in ax25_sendmsg()
sctp: shrink stream outq when fails to do addstream reconf
sctp: shrink stream outq only when new outcnt < old outcnt
AX.25: Fix out-of-bounds read in ax25_connect()
enetc: Remove the mdio bus on PF probe bailout
net: ethernet: ti: add NETIF_F_HW_TC hw feature flag for taprio offload
net: ethernet: ave: Fix error returns in ave_init
drivers/net/wan/x25_asy: Fix to make it work
ipvs: fix the connection sync failed in some cases
...
IRQs are disabled when freeing skbs in input queue.
Use the IRQ safe variant to free skbs here.
Fixes: 145dd5f9c8 ("net: flush the softnet backlog in process context")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have to detach sock from socket in qrtr_release(),
otherwise skb->sk may still reference to this socket
when the skb is released in tun->queue, particularly
sk->sk_wq still points to &sock->wq, which leads to
a UAF.
Reported-and-tested-by: syzbot+6720d64f31c081c2f708@syzkaller.appspotmail.com
Fixes: 28fb4e59a4 ("net: qrtr: Expose tunneling endpoint to user space")
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
l2tp_session_free called BUG_ON if the tunnel magic feather value wasn't
correct. The intent of this was to catch lifetime bugs; for example
early tunnel free due to incorrect use of reference counts.
Since the tunnel magic feather being wrong indicates either early free
or structure corruption, we can avoid doing more damage by simply
leaving the tunnel structure alone. If the tunnel refcount isn't
dropped when it should be, the tunnel instance will remain in the
kernel, resulting in the tunnel structure and socket leaking.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
l2tp_session_free is only called by l2tp_session_dec_refcount when the
reference count reaches zero, so it's of limited value to validate the
reference count value in l2tp_session_free itself.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
l2tp_session_queue_purge is used during session shutdown to drop any
skbs queued for reordering purposes according to L2TP dataplane rules.
The BUG_ON in this function checks the session magic feather in an
attempt to catch lifetime bugs.
Rather than crashing the kernel with a BUG_ON, we can simply WARN_ON and
refuse to do anything more -- in the worst case this could result in a
leak. However this is highly unlikely given that the session purge only
occurs from codepaths which have obtained the session by means of a lookup
via. the parent tunnel and which check the session "dead" flag to
protect against shutdown races.
While we're here, have l2tp_session_queue_purge return void rather than
an integer, since neither of the callsites checked the return value.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch advises that WARN_ON and recovery code are preferred over
BUG_ON which crashes the kernel.
l2tp_ppp has a BUG_ON check of struct seq_file's private pointer in
pppol2tp_seq_start prior to accessing data through that pointer.
Rather than crashing, we can simply bail out early and return NULL in
order to terminate the seq file processing in much the same way as we do
when reaching the end of tunnel/session instances to render.
Retain a WARN_ON to help trace possible bugs in this area.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch advises that WARN_ON and recovery code are preferred over
BUG_ON which crashes the kernel.
l2tp_ppp.c's BUG_ON checks of the l2tp session structure's "magic" field
occur in code paths where it's reasonably easy to recover:
* In the case of pppol2tp_sock_to_session, we can return NULL and the
caller will bail out appropriately. There is no change required to
any of the callsites of this function since they already handle
pppol2tp_sock_to_session returning NULL.
* In the case of pppol2tp_session_destruct we can just avoid
decrementing the reference count on the suspect session structure.
In the worst case scenario this results in a memory leak, which is
preferable to a crash.
Convert these uses of BUG_ON to WARN_ON accordingly.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
l2tp_tunnel_closeall is only called from l2tp_core.c, and it's easy
to statically analyse the code path calling it to validate that it
should never be passed a NULL tunnel pointer.
Having a BUG_ON checking the tunnel pointer triggers a checkpatch
warning. Since the BUG_ON is of no value, remove it to avoid the
warning.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
l2tp_session_queue_purge is only called from l2tp_core.c, and it's easy
to statically analyse the code paths calling it to validate that it
should never be passed a NULL session pointer.
Having a BUG_ON checking the session pointer triggers a checkpatch
warning. Since the BUG_ON is of no value, remove it to avoid the
warning.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
l2tp_dfs_seq_start had a BUG_ON to catch a possible programming error in
l2tp_dfs_seq_open.
Since we can easily bail out of l2tp_dfs_seq_start, prefer to do that
and flag the error with a WARN_ON rather than crashing the kernel.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch warns about multiple assignments.
Update l2tp accordingly.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the rfc 4884 read interface introduced for ipv4 in
commit eba75c587e ("icmp: support rfc 4884") to ipv6.
Add socket option SOL_IPV6/IPV6_RECVERR_RFC4884.
Changes v1->v2:
- make ipv6_icmp_error_rfc4884 static (file scope)
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RFC 4884 spec is largely the same between IPv4 and IPv6.
Factor out the IPv4 specific parts in preparation for IPv6 support:
- icmp types supported
- icmp header size, and thus offset to original datagram start
- datagram length field offset in icmp(6)hdr.
- datagram length field word size: 4B for IPv4, 8B for IPv6.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Only accept packets with original datagram len field >= header len.
The extension header must start after the original datagram headers.
The embedded datagram len field is compared against the 128B minimum
stipulated by RFC 4884. It is unlikely that headers extend beyond
this. But as we know the exact header length, check explicitly.
2) Remove the check that datagram length must be <= 576B.
This is a send constraint. There is no value in testing this on rx.
Within private networks it may be known safe to send larger packets.
Process these packets.
This test was also too lax. It compared original datagram length
rather than entire icmp packet length. The stand-alone fix would be:
- if (hlen + skb->len > 576)
+ if (-skb_network_offset(skb) + skb->len > 576)
Fixes: eba75c587e ("icmp: support rfc 4884")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable status is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed. Also put the variable declarations into
reverse christmas tree order.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch introduced a deadlock, this patch fixes it by making
sure the work is canceled without holding the global ovs lock. This is
done by moving the reorder processing one layer up to the netns level.
Fixes: eac87c413b ("net: openvswitch: reorder masks array based on usage")
Reported-by: syzbot+2c4ff3614695f75ce26c@syzkaller.appspotmail.com
Reported-by: syzbot+bad6507e5db05017b008@syzkaller.appspotmail.com
Reviewed-by: Paolo <pabeni@redhat.com>
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This sockopt accepts two kinds of parameters, using struct
sctp_sack_info and struct sctp_assoc_value. The mentioned commit didn't
notice an implicit cast from the smaller (latter) struct to the bigger
one (former) when copying the data from the user space, which now leads
to an attempt to write beyond the buffer (because it assumes the storing
buffer is bigger than the parameter itself).
Fix it by allocating a sctp_sack_info on stack and filling it out based
on the small struct for the compat case.
Changelog stole from an earlier patch from Marcelo Ricardo Leitner.
Fixes: ebb25defdc ("sctp: pass a kernel pointer to sctp_setsockopt_delayed_ack")
Reported-by: syzbot+0e4699d000d8b874d8dc@syzkaller.appspotmail.com
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For architectures like x86 and arm64 we don't need the separate bit to
indicate that a pointer is a kernel pointer as the address spaces are
unified. That way the sockptr_t can be reduced to a union of two
pointers, which leads to nicer calling conventions.
The only caveat is that we need to check that users don't pass in kernel
address and thus gain access to kernel memory. Thus the USER_SOCKPTR
helper is replaced with a init_user_sockptr function that does this check
and returns an error if it fails.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework the remaining setsockopt code to pass a sockptr_t instead of a
plain user pointer. This removes the last remaining set_fs(KERNEL_DS)
outside of architecture specific code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org> [ieee802154]
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factour out a helper to set the IPv6 option headers from
do_ipv6_setsockopt.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Note that the get case is pretty weird in that it actually copies data
back to userspace from setsockopt.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split ipv6_flowlabel_opt into a subfunction for each action and a small
wrapper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is mostly to prepare for cleaning up the callers, as bpfilter by
design can't handle kernel pointers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bpfilter user mode helper processes the optval address using
process_vm_readv. Don't send it kernel addresses fed under
set_fs(KERNEL_DS) as that won't work.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split __bpfilter_process_sockopt into a low-level send request routine and
the actual setsockopt hook to split the init time ping from the actual
setsockopt processing.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __user doesn't make sense when casting to an integer type, just
switch to a uintptr_t cast which also removes the need for the __force.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding new cls flower keys for hash value and hash
mask and dissect the hash info from the skb into
the flow key towards flow classication.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Retreive a hash value from the SKB and store it
in the dissector key for future matching.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I noticed that touching linux/rhashtable.h causes lib/vsprintf.c to
be rebuilt. This dependency came through a bogus inclusion in the
file net/flow_offload.h. This patch moves it to the right place.
This patch also removes a lingering rhashtable inclusion in cls_api
created by the same commit.
Fixes: 4e481908c5 ("flow_offload: move tc indirect block to...")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Braino when converting "buf->len -=" to "buf->len = len -".
The result is under-estimation of the ralign and rslack values. On
krb5p mounts, this has caused READDIR to fail with EIO, and KASAN
splats when decoding READLINK replies.
As a result of fixing this oversight, the gss_unwrap method now
returns a buf->len that can be shorter than priv_len for small
RPC messages. The additional adjustment done in unwrap_priv_data()
can underflow buf->len. This causes the nfsd_request_too_large
check to fail during some NFSv3 operations.
Reported-by: Marian Rainer-Harbach
Reported-by: Pierre Sauter <pierre.sauter@stwm.de>
BugLink: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1886277
Fixes: 31c9590ae4 ("SUNRPC: Add "@len" parameter to gss_unwrap()")
Reviewed-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for net:
1) Fix NAT hook deletion when table is dormant, from Florian Westphal.
2) Fix IPVS sync stalls, from guodeqing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The purpose of this override is to give the user an indication of what
the number of the CPU port is (in DSA, the CPU port is a hardware
implementation detail and not a network interface capable of traffic).
However, it has always failed (by design) at providing this information
to the user in a reliable fashion.
Prior to commit 3369afba1e ("net: Call into DSA netdevice_ops
wrappers"), the behavior was to only override this callback if it was
not provided by the DSA master.
That was its first failure: if the DSA master itself was a DSA port or a
switchdev, then the user would not see the number of the CPU port in
/sys/class/net/eth0/phys_port_name, but the number of the DSA master
port within its respective physical switch.
But that was actually ok in a way. The commit mentioned above changed
that behavior, and now overrides the master's ndo_get_phys_port_name
unconditionally. That comes with problems of its own, which are worse in
a way.
The idea is that it's typical for switchdev users to have udev rules for
consistent interface naming. These are based, among other things, on
the phys_port_name attribute. If we let the DSA switch at the bottom
to start randomly overriding ndo_get_phys_port_name with its own CPU
port, we basically lose any predictability in interface naming, or even
uniqueness, for that matter.
So, there are reasons to let DSA override the master's callback (to
provide a consistent interface, a number which has a clear meaning and
must not be interpreted according to context), and there are reasons to
not let DSA override it (it breaks udev matching for the DSA master).
But, there is an alternative method for users to retrieve the number of
the CPU port of each DSA switch in the system:
$ devlink port
pci/0000:00:00.5/0: type eth netdev swp0 flavour physical port 0
pci/0000:00:00.5/2: type eth netdev swp2 flavour physical port 2
pci/0000:00:00.5/4: type notset flavour cpu port 4
spi/spi2.0/0: type eth netdev sw0p0 flavour physical port 0
spi/spi2.0/1: type eth netdev sw0p1 flavour physical port 1
spi/spi2.0/2: type eth netdev sw0p2 flavour physical port 2
spi/spi2.0/4: type notset flavour cpu port 4
spi/spi2.1/0: type eth netdev sw1p0 flavour physical port 0
spi/spi2.1/1: type eth netdev sw1p1 flavour physical port 1
spi/spi2.1/2: type eth netdev sw1p2 flavour physical port 2
spi/spi2.1/3: type eth netdev sw1p3 flavour physical port 3
spi/spi2.1/4: type notset flavour cpu port 4
So remove this duplicated, unreliable and troublesome method. From this
patch on, the phys_port_name attribute of the DSA master will only
contain information about itself (if at all). If the users need reliable
information about the CPU port they're probably using devlink anyway.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously TLP may send multiple probes of new data in one
flight. This happens when the sender is cwnd limited. After the
initial TLP containing new data is sent, the sender receives another
ACK that acks partial inflight. It may re-arm another TLP timer
to send more, if no further ACK returns before the next TLP timeout
(PTO) expires. The sender may send in theory a large amount of TLP
until send queue is depleted. This only happens if the sender sees
such irregular uncommon ACK pattern. But it is generally undesirable
behavior during congestion especially.
The original TLP design restrict only one TLP probe per inflight as
published in "Reducing Web Latency: the Virtue of Gentle Aggression",
SIGCOMM 2013. This patch changes TLP to send at most one probe
per inflight.
Note that if the sender is app-limited, TLP retransmits old data
and did not have this issue.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We recently added some bounds checking in ax25_connect() and
ax25_sendmsg() and we so we removed the AX25_MAX_DIGIS checks because
they were no longer required.
Unfortunately, I believe they are required to prevent integer overflows
so I have added them back.
Fixes: 8885bb0621 ("AX.25: Prevent out-of-bounds read in ax25_sendmsg()")
Fixes: 2f2a7ffad5 ("AX.25: Fix out-of-bounds read in ax25_connect()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Passing "sizeof(struct blah)" in kzalloc calls is less readable,
potentially prone to future bugs if the type of the pointer is changed,
and triggers checkpatch warnings.
Tweak the kzalloc calls in l2tp which use this form to avoid the
warning.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating an L2TP tunnel using the netlink API, userspace must
either pass a socket FD for the tunnel to use (for managed tunnels),
or specify the tunnel source/destination address (for unmanaged
tunnels).
Since source/destination addresses may be AF_INET or AF_INET6, the l2tp
netlink code has conditionally compiled blocks to support IPv6.
Rather than embedding these directly into l2tp_nl_cmd_tunnel_create
(where it makes the code difficult to read and confuses checkpatch to
boot) split the handling of address-related attributes into a separate
function.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
l2tp_nl_tunnel_send has conditionally compiled code to support AF_INET6,
which makes the code difficult to follow and triggers checkpatch
warnings.
Split the code out into functions to handle the AF_INET v.s. AF_INET6
cases, which both improves readability and resolves the checkpatch
warnings.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch warns about indentation and brace balancing around the
conditionally compiled code for AF_INET6 support in
l2tp_dfs_seq_tunnel_show.
By adding another check on the socket address type we can make the code
more readable while removing the checkpatch warning.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These checks are all simple and don't benefit from extra braces to
clarify intent. Remove them for easier-reading code.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch warns about comparisons to NULL, e.g.
CHECK: Comparison to NULL could be written "!rt"
#474: FILE: net/l2tp/l2tp_ip.c:474:
+ if (rt == NULL) {
These sort of comparisons are generally clearer and more readable
the way checkpatch suggests, so update l2tp accordingly.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_zero_addr() to clear mac address insetad of memset().
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So that we can easily perform some basic PM-related
adimission checks before creating the child socket.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_send_active_reset() is more prone to transient errors
(memory allocation or xmit queue full): in stress conditions
the kernel may drop the egress packet, and the client will be
stuck.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When syncookie are in use, the TCP stack may feed into
subflow_syn_recv_sock() plain TCP request sockets. We can't
access mptcp_subflow_request_sock-specific fields on such
sockets. Explicitly check the rsk ops to do safe accesses.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mentioned function has several unneeded branches,
handle each case - MP_CAPABLE, MP_JOIN, fallback -
under a single conditional and drop quite a bit of
duplicate code.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently accepted msk sockets become established only after
accept() returns the new sk to user-space.
As MP_JOIN request are refused as per RFC spec on non fully
established socket, the above causes mp_join self-tests
instabilities.
This change lets the msk entering the established status
as soon as it receives the 3rd ack and propagates the first
subflow fully established status on the msk socket.
Finally we can change the subflow acceptance condition to
take in account both the sock state and the msk fully
established flag.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the unlikely event of a failure at connect time,
we currently clear the request_mptcp flag - so that
the MPC handshake is not started at all, but the msk
is not explicitly marked as fallback.
This would lead to later insertion of wrong DSS options
in the xmitted packets, in violation of RFC specs and
possibly fooling the peer.
Fixes: e1ff9e82e2 ("net: mptcp: improve fallback to TCP")
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When updating a partially acked data fragment, we
actually corrupt it. This is irrelevant till we send
data on a single subflow, as retransmitted data, if
any are discarded by the peer as duplicate, but it
will cause data corruption as soon as we will start
creating non backup subflows.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we do not init the subflow write sequence for
MP_JOIN subflows. This will cause bad mapping being
generated as soon as we will use non backup subflow.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch warned about the L2TP_SKB_CB macro's use of its argument: add
braces to avoid the problem.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In l2tp_core.c both l2tp_tunnel_create and l2tp_session_create take
quite a number of arguments and have a correspondingly long prototype.
This is both quite difficult to scan visually, and triggers checkpatch
warnings.
Add a line break to make these function prototypes more readable.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch warns about use of seq_printf where seq_puts would do.
Modify l2tp_debugfs accordingly.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use BIT(x) rather than (1<<x), reported by checkpatch.pl.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported by checkpatch:
"WARNING: function definition argument 'struct sock *'
should also have an identifier name"
Add an identifier name to help document the prototype.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
l2tp_core has conditionally compiled code in l2tp_xmit_skb for IPv6
support. The structure of this code triggered a checkpatch warning
due to incorrect indentation.
Fix up the indentation to address the checkpatch warning.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arguments should be aligned with the function call open parenthesis as
per checkpatch. Tweak some function calls which were not aligned
correctly.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some l2tp code had line breaks which made the code more difficult to
read. These were originally motivated by the 80-character line width
coding guidelines, but were actually a negative from the perspective of
trying to follow the code.
Remove these linebreaks for clearer code, even if we do exceed 80
characters in width in some places.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify some l2tp comments to better adhere to kernel coding style, as
reported by checkpatch.pl.
Add descriptive comments for the l2tp per-net spinlocks to document
their use.
Fix an incorrect comment in l2tp_recv_common:
RFC2661 section 5.4 states that:
"The LNS controls enabling and disabling of sequence numbers by sending a
data message with or without sequence numbers present at any time during
the life of a session."
l2tp handles this correctly in l2tp_recv_common, but the comment around
the code was incorrect and confusing. Fix up the comment accordingly.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up various whitespace issues as reported by checkpatch.pl:
* remove spaces around operators where appropriate,
* add missing blank lines following declarations,
* remove multiple blank lines, or trailing blank lines at the end of
functions.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checks on `addr_len` and `usax->sax25_ndigis` are insufficient.
ax25_sendmsg() can go out of bounds when `usax->sax25_ndigis` equals to 7
or 8. Fix it.
It is safe to remove `usax->sax25_ndigis > AX25_MAX_DIGIS`, since
`addr_len` is guaranteed to be less than or equal to
`sizeof(struct full_sockaddr_ax25)`
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently devlink instance is searched on all doit() operations.
But it is optionally stored into user_ptr[0]. This requires
rediscovering devlink again doing post_doit().
Few devlink commands related to port shared buffers needs 3 pointers
(devlink, devlink_port, and devlink_sb) while executing doit commands.
Though devlink pointer can be derived from the devlink_port during
post_doit() operation when doit() callback has acquired devlink
instance lock, relying on such scheme to access devlik pointer makes
code very fragile.
Hence, to avoid ambiguity in post_doit() and to avoid searching
devlink instance again, simplify code by always storing devlink
instance in user_ptr[0] and derive devlink_sb pointer in their
respective callback routines.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding a stream with stream reconf, the new stream firstly is in
CLOSED state but new out chunks can still be enqueued. Then once gets
the confirmation from the peer, the state will change to OPEN.
However, if the peer denies, it needs to roll back the stream. But when
doing that, it only sets the stream outcnt back, and the chunks already
in the new stream don't get purged. It caused these chunks can still be
dequeued in sctp_outq_dequeue_data().
As its stream is still in CLOSE, the chunk will be enqueued to the head
again by sctp_outq_head_data(). This chunk will never be sent out, and
the chunks after it can never be dequeued. The assoc will be 'hung' in
a dead loop of sending this chunk.
To fix it, this patch is to purge these chunks already in the new
stream by calling sctp_stream_shrink_out() when failing to do the
addstream reconf.
Fixes: 11ae76e67a ("sctp: implement receiver-side procedures for the Reconf Response Parameter")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not necessary to go list_for_each for outq->out_chunk_list
when new outcnt >= old outcnt, as no chunk with higher sid than
new (outcnt - 1) exists in the outqueue.
While at it, also move the list_for_each code in a new function
sctp_stream_shrink_out(), which will be used in the next patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise the 'chain_len' filed will carry random values,
some token creation calls will fail due to excessive chain
length, causing unexpected fallback to TCP.
Fixes: 2c5ebd001d ("mptcp: refactor token container")
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checks on `addr_len` and `fsa->fsa_ax25.sax25_ndigis` are insufficient.
ax25_connect() can go out of bounds when `fsa->fsa_ax25.sax25_ndigis`
equals to 7 or 8. Fix it.
This issue has been reported as a KMSAN uninit-value bug, because in such
a case, ax25_connect() reaches into the uninitialized portion of the
`struct sockaddr_storage` statically allocated in __sys_connect().
It is safe to remove `fsa->fsa_ax25.sax25_ndigis > AX25_MAX_DIGIS` because
`addr_len` is guaranteed to be less than or equal to
`sizeof(struct full_sockaddr_ax25)`.
Reported-by: syzbot+c82752228ed975b0a623@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=55ef9d629f3b3d7d70b69558015b63b48d01af66
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the SIOCOUTQ IOCTL to get the send buffer fill
of a DCCP socket, like UDP and TCP sockets already have.
Regarding the used data field: DCCP uses per packet sequence numbers,
not per byte, so sequence numbers can't be used like in TCP. sk_wmem_queued
is not used by DCCP and always 0, even in test on highly congested paths.
Therefore this uses sk_wmem_alloc like in UDP.
Signed-off-by: Richard Sailer <richard_siegfried@systemli.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to unified Ethernet Switch Device Tree Bindings allow for ethernet-ports as
encapsulating node as well.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The buildbot found a config where the header isn't already implicitly
pulled in, so add an explicit include as well.
Fixes: 8c918ffbba ("net: remove compat_sock_common_{get,set}sockopt")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-07-21
The following pull-request contains BPF updates for your *net-next* tree.
We've added 46 non-merge commits during the last 6 day(s) which contain
a total of 68 files changed, 4929 insertions(+), 526 deletions(-).
The main changes are:
1) Run BPF program on socket lookup, from Jakub.
2) Introduce cpumap, from Lorenzo.
3) s390 JIT fixes, from Ilya.
4) teach riscv JIT to emit compressed insns, from Luke.
5) use build time computed BTF ids in bpf iter, from Yonghong.
====================
Purely independent overlapping changes in both filter.h and xdp.h
Signed-off-by: David S. Miller <davem@davemloft.net>
In pfkey_dump() dplen and splen can both be specified to access the
xfrm_address_t structure out of bounds in__xfrm_state_filter_match()
when it calls addr_match() with the indexes. Return EINVAL if either
are out of range.
Signed-off-by: Mark Salyzyn <salyzyn@android.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: kernel-team@android.com
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The sync_thread_backup only checks sk_receive_queue is empty or not,
there is a situation which cannot sync the connection entries when
sk_receive_queue is empty and sk_rmem_alloc is larger than sk_rcvbuf,
the sync packets are dropped in __udp_enqueue_schedule_skb, this is
because the packets in reader_queue is not read, so the rmem is
not reclaimed.
Here I add the check of whether the reader_queue of the udp sock is
empty or not to solve this problem.
Fixes: 2276f58ac5 ("udp: use a separate rx queue for packet reception")
Reported-by: zhouxudong <zhouxudong8@huawei.com>
Signed-off-by: guodeqing <geffrey.guo@huawei.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When expire_nodest_conn=1 and a destination is deleted, IPVS does not
expire the existing connections until the next matching incoming packet.
If there are many connection entries from a single client to a single
destination, many packets may get dropped before all the connections are
expired (more likely with lots of UDP traffic). An optimization can be
made where upon deletion of a destination, IPVS queues up delayed work
to immediately expire any connections with a deleted destination. This
ensures any reused source ports from a client (within the IPVS timeouts)
are scheduled to new real servers instead of silently dropped.
Signed-off-by: Andrew Sy Kim <kim.andrewsy@gmail.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Constify devlink instance pointer while checking if reload operation is
supported or not.
This helps to review the scope of checks done in reload.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reload operation is enabled or not is already checked by
devlink_reload(). Hence, remove the duplicate check from
devlink_nl_cmd_reload().
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to hold a device global lock when initializing
devlink device fields of a devlink instance which is not yet part of the
devices list.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't use IS_UDPLITE to replace udp_sk->pcflag when UDPLITE_RECV_CC is
checked.
Fixes: b2bf1e2659 ("[UDP]: Clean up for IS_UDPLITE macro")
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I cat 'tx_timeout' by sysfs, it displays as follows. It's better to
add a newline for easy reading.
root@syzkaller:~# cat /sys/devices/virtual/net/lo/queues/tx-0/tx_timeout
0root@syzkaller:~#
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, SO_REUSEPORT does not work well if connected sockets are in a
UDP reuseport group.
Then reuseport_has_conns() returns true and the result of
reuseport_select_sock() is discarded. Also, unconnected sockets have the
same score, hence only does the first unconnected socket in udp_hslot
always receive all packets sent to unconnected sockets.
So, the result of reuseport_select_sock() should be used for load
balancing.
The noteworthy point is that the unconnected sockets placed after
connected sockets in sock_reuseport.socks will receive more packets than
others because of the algorithm in reuseport_select_sock().
index | connected | reciprocal_scale | result
---------------------------------------------
0 | no | 20% | 40%
1 | no | 20% | 20%
2 | yes | 20% | 0%
3 | no | 20% | 40%
4 | yes | 20% | 0%
If most of the sockets are connected, this can be a problem, but it still
works better than now.
Fixes: acdcecc612 ("udp: correct reuseport selection with connected sockets")
CC: Willem de Bruijn <willemb@google.com>
Reviewed-by: Benjamin Herrenschmidt <benh@amazon.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an unconnected socket in a UDP reuseport group connect()s, has_conns is
set to 1. Then, when a packet is received, udp[46]_lib_lookup2() scans all
sockets in udp_hslot looking for the connected socket with the highest
score.
However, when the number of sockets bound to the port exceeds max_socks,
reuseport_grow() resets has_conns to 0. It can cause udp[46]_lib_lookup2()
to return without scanning all sockets, resulting in that packets sent to
connected sockets may be distributed to unconnected sockets.
Therefore, reuseport_grow() should copy has_conns.
Fixes: acdcecc612 ("udp: correct reuseport selection with connected sockets")
CC: Willem de Bruijn <willemb@google.com>
Reviewed-by: Benjamin Herrenschmidt <benh@amazon.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One additional field btf_id is added to struct
bpf_ctx_arg_aux to store the precomputed btf_ids.
The btf_id is computed at build time with
BTF_ID_LIST or BTF_ID_LIST_GLOBAL macro definitions.
All existing bpf iterators are changed to used
pre-compute btf_ids.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200720163403.1393551-1-yhs@fb.com
tcp and udp bpf_iter can reuse some socket ids in
btf_sock_ids, so make it global.
I put the extern definition in btf_ids.h as a central
place so it can be easily discovered by developers.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200720163402.1393427-1-yhs@fb.com
Currently, socket types (struct tcp_sock, udp_sock, etc.)
used by bpf_skc_to_*() helpers are computed when vmlinux_btf
is first built in the kernel.
Commit 5a2798ab32
("bpf: Add BTF_ID_LIST/BTF_ID/BTF_ID_UNUSED macros")
implemented a mechanism to compute btf_ids at kernel build
time which can simplify kernel implementation and reduce
runtime overhead by removing in-kernel btf_id calculation.
This patch did exactly this, removing in-kernel btf_id
computation and utilizing build-time btf_id computation.
If CONFIG_DEBUG_INFO_BTF is not defined, BTF_ID_LIST will
define an array with size of 5, which is not enough for
btf_sock_ids. So define its own static array if
CONFIG_DEBUG_INFO_BTF is not defined.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200720163358.1393023-1-yhs@fb.com
The generic netlink is initialized far after the netlink protocol
itself at subsys_initcall. The devlink is initialized at the same
level, but after, as shown by a disassembly of the vmlinux:
[ ... ]
374 ffff8000115f22c0 <__initcall_devlink_init4>:
375 ffff8000115f22c4 <__initcall_genl_init4>:
[ ... ]
The function devlink_init() calls genl_register_family() before the
generic netlink subsystem is initialized.
As the generic netlink initcall level is set since 2005, it seems that
was not a problem, but now we have the thermal framework initialized
at the core_initcall level which creates the generic netlink family
and sends a notification which leads to a subtle memory corruption
only detectable when the CONFIG_INIT_ON_ALLOC_DEFAULT_ON option is set
with the earlycon at init time.
The thermal framework needs to be initialized early in order to begin
the mitigation as soon as possible. Moving it to postcore_initcall is
acceptable.
This patch changes the initialization level for the generic netlink
family to the core_initcall and comes after the netlink protocol
initialization.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: David S. Miller <davem@davemloft.net>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/20200715074120.8768-1-daniel.lezcano@linaro.org
We forgot to support the xfrm policy hold queue when
VTI was implemented. This patch adds everything we
need so that we can use the policy hold queue together
with VTI interfaces.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Commit 02288248b0 ("tipc: eliminate gap indicator from ACK messages")
eliminated sending of the 'gap' indicator in regular ACK messages and
only allowed to build NACK message with enabled probe/probe_reply.
However, necessary correction for building NACK message was missed
in tipc_link_timeout() function. This leads to significant delay and
link reset (due to retransmission failure) in lossy environment.
This commit fixes it by setting the 'probe' flag to 'true' when
the receive deferred queue is not empty. As a result, NACK message
will be built to send back to another peer.
Fixes: 02288248b0 ("tipc: eliminate gap indicator from ACK messages")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fragment packets do defrag in tcf_ct_handle_fragments
will clear the skb->cb which make the qdisc_skb_cb clear
too. So the qdsic_skb_cb should be store before defrag and
restore after that.
It also update the pkt_len after all the
fragments finish the defrag to one packet and make the
following actions counter correct.
Fixes: b57dc7c13e ("net/sched: Introduce action ct")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that DSA supports MTU configuration, undo the effects of commit
8b1efc0f83 ("net: remove MTU limits on a few ether_setup callers") and
let DSA interfaces use the default min_mtu and max_mtu specified by
ether_setup(). This is more important for min_mtu: since DSA is
Ethernet, the minimum MTU is the same as of any other Ethernet
interface, and definitely not zero. For the max_mtu, we have a callback
through which drivers can override that, if they want to.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because kfree_skb already checked NULL skb parameter,
so the additional checks are unnecessary, just remove them.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_put_padto() can fail. So check for return type and return NULL
for skb. Caller checks for skb and acts correctly if it is NULL.
Fixes: 6d6148bc78 ("net: hsr: fix incorrect lsdu size in the tag of HSR frames for small frames")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a current limit of 1920 registered dmb buffers per ISM device
for smc-d. One link group can contain 255 connections, each connection
is using one dmb buffer. When the connection is closed then the
registered buffer is held in a queue and is reused by the next
connection. When a link group is 'full' then another link group is
created and uses an own buffer pool. The link groups are added to a
list using list_add() which puts a new link group to the first position
in the list.
In the situation that many connections are opened (>1920) and a few of
them stay open while others are closed quickly we end up with at least 8
link groups. For a new connection a matching link group is looked up,
iterating over the list of link groups. The trailing 7 link groups
all have registered dmb buffers which could be reused, while the first
link group has only a few dmb buffers and then hit the 1920 limit.
Because the first link group is not full (255 connection limit not
reached) it is chosen and finally the connection falls back to TCP
because there is no dmb buffer available in this link group.
There are multiple ways to fix that: using list_add_tail() allows
to scan older link groups first for free buffers which ensures that
buffers are reused first. This fixes the problem for smc-r link groups
as well. For smc-d there is an even better way to address this problem
because smc-d does not have the 255 connections per link group limit.
So fix the problem for smc-d by allowing large link groups.
Fixes: c6ba7c9ba4 ("net/smc: add base infrastructure for SMC-D and ISM")
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To get a send slot smc_wr_tx_get_free_slot() is called, which might
wait for a free slot. When smc_wr_tx_get_free_slot() returns there is a
check if the connection was killed in the meantime. In that case don't
only return an error, but also put back the free slot.
Fixes: b290098092 ("net/smc: cancel send and receive for terminated socket")
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rxrpc_sendmsg() returns EPIPE if there's an outstanding error, such as if
rxrpc_recvmsg() indicating ENODATA if there's nothing for it to read.
Change rxrpc_recvmsg() to return EAGAIN instead if there's nothing to read
as this particular error doesn't get stored in ->sk_err by the networking
core.
Also change rxrpc_sendmsg() so that it doesn't fail with delayed receive
errors (there's no way for it to report which call, if any, the error was
caused by).
Fixes: 17926a7932 ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have all the infrastructure in place for calling into the
dsa_ptr->netdev_ops function pointers, install them when we configure
the DSA CPU/management interface and tear them down. The flow is
unchanged from before, but now we preserve equality of tests when
network device drivers do tests like dev->netdev_ops == &foo_ops which
was not the case before since we were allocating an entirely new
structure.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the core net_device code call into our ndo_do_ioctl() and
ndo_get_phys_port_name() functions via the wrappers defined previously
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for adding another layer of call into a DSA stacked ops
singleton, wrap the ndo_do_ioctl() call into dev_do_ioctl().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add setsockopt SOL_IP/IP_RECVERR_4884 to return the offset to an
extension struct if present.
ICMP messages may include an extension structure after the original
datagram. RFC 4884 standardized this behavior. It stores the offset
in words to the extension header in u8 icmphdr.un.reserved[1].
The field is valid only for ICMP types destination unreachable, time
exceeded and parameter problem, if length is at least 128 bytes and
entire packet does not exceed 576 bytes.
Return the offset to the start of the extension struct when reading an
ICMP error from the error queue, if it matches the above constraints.
Do not return the raw u8 field. Return the offset from the start of
the user buffer, in bytes. The kernel does not return the network and
transport headers, so subtract those.
Also validate the headers. Return the offset regardless of validation,
as an invalid extension must still not be misinterpreted as part of
the original datagram. Note that !invalid does not imply valid. If
the extension version does not match, no validation can take place,
for instance.
For backward compatibility, make this optional, set by setsockopt
SOL_IP/IP_RECVERR_RFC4884. For API example and feature test, see
github.com/wdebruij/kerneltools/blob/master/tests/recv_icmp_v2.c
For forward compatibility, reserve only setsockopt value 1, leaving
other bits for additional icmp extensions.
Changes
v1->v2:
- convert word offset to byte offset from start of user buffer
- return in ee_data as u8 may be insufficient
- define extension struct and object header structs
- return len only if constraints met
- if returning len, also validate
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is just used once, and a direct return for the redirect to the AF
case is much easier to follow than jumping to the end of a very long
function.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer. Adapt sctp_setsockopt to use a
kzfree for this case.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch from kzfree to sctp_setsockopt_auth_key + kfree to prepare for
moving the kfree to common code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename sctp_setsockopt_bindx_kernel back to sctp_setsockopt_bindx,
and use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer in the old sctp_setsockopt_bindx.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare for for moving the copy_from_user from the individual sockopts
to the main setsockopt helper. As of this commit the kopt variable
is not used yet, but the following commits will start using it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just check for a NULL method instead of wiring up
sock_no_{get,set}sockopt.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle the few cases that need special treatment in-line using
in_compat_syscall(). This also removes all the now unused
compat_{get,set}sockopt methods.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out one helper each for setting the native and compat
version of the MCAST_MSFILTER option.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out one helper each for setting the native and compat
version of the MCAST_MSFILTER option.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out one helper each for getting the native and compat
version of the MCAST_MSFILTER option.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle the few cases that need special treatment in-line using
in_compat_syscall().
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out one helper each for setting the native and compat
version of the MCAST_MSFILTER option.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out one helper each for setting the native and compat
version of the MCAST_MSFILTER option.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out one helper each for getting the native and compat
version of the MCAST_MSFILTER option.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split nf_sockopt into a getsockopt and setsockopt side as they share
very little code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lift the in_compat_syscall() from the callers instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
All instances handle compat sockopts via in_compat_syscall() now, so
remove the compat_{get,set} methods as well as the
compat_nf_{get,set}sockopt wrappers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge the native and compat {get,set}sockopt handlers using
in_compat_syscall(). Note that this required moving a fair
amout of code around to be done sanely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge the native and compat {get,set}sockopt handlers using
in_compat_syscall().
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge the native and compat {get,set}sockopt handlers using
in_compat_syscall().
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge the native and compat {get,set}sockopt handlers using
in_compat_syscall().
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the ->compat_{get,set}sockopt proto_ops methods are gone
there is no good reason left to keep the compat syscalls separate.
This fixes the odd use of unsigned int for the compat_setsockopt
optlen and the missing sock_use_custom_sol_socket.
It would also easily allow running the eBPF hooks for the compat
syscalls, but such a large change in behavior does not belong into
a consolidation patch like this one.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the compat handling to sock_common_{get,set}sockopt instead,
keyed of in_compat_syscall(). This allow to remove the now unused
->compat_{get,set}sockopt methods from struct proto_ops.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper that copies either a native or compat bpf_fprog from
userspace after verifying the length, and remove the compat setsockopt
handlers that now aren't required.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return early when sockfd_lookup_light fails to reduce a level of
indentation for most of the function body.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return early when sockfd_lookup_light fails to reduce a level of
indentation for most of the function body.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
All implementations of these two methods are dummies that always
return -EINVAL.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delete the doubled word "be" in a comment.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Cc: netdev@vger.kernel.org
Cc: linux-rdma@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Delete the doubled word "the" in a comment.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
When a listen socket is closed then all non-accepted sockets in its
accept queue are to be released. Inside __smc_release() the helper
smc_restore_fallback_changes() restores the changes done to the socket
without to check if the clcsocket has a file set. This can result in
a crash. Fix this by checking the file pointer first.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: f536dffc0b ("net/smc: fix closing of fallback SMC sockets")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two buffers are allocated for each SMC connection. Each buffer is
added to a buffer list after creation. When the second buffer
allocation fails, the first buffer is freed but not deleted from
the list. This might result in crashes when another connection picks
up the freed buffer later and starts to work with it.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: 6511aad3f0 ("net/smc: change smc_buf_free function parameters")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dma related ...sync_sg... functions check the link state before the
dma function is actually called. But the check in smc_link_usable()
allows links in ACTIVATING state which are not yet mapped to dma memory.
Under high load it may happen that the sync_sg functions are called for
such a link which results in an debug output like
DMA-API: mlx5_core 0002:00:00.0: device driver tries to sync
DMA memory it has not allocated [device address=0x0000000103370000]
[size=65536 bytes]
To fix that introduce a helper to check for the link state ACTIVE and
use it where appropriate. And move the link state update to ACTIVATING
to the end of smcr_link_init() when most initial setup is done.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: d854fcbfae ("net/smc: add new link state and related helpers")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As smc client the delete link requests are assigned to the flow when
_any_ flow is active. This may break other flows that do not expect
delete link requests during their handling. Fix that by assigning the
request only when an add link flow is active. With that fix the code
for smc client and smc server is the same, so remove the separate
handling.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: 9ec6bf19ec ("net/smc: llc_del_link_work and use the LLC flow for delete link")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new ib device is up smc will send an add link invitation to the
peer if needed. This is currently done with rudimentary flow control.
Under high workload these add link invitations can disturb other llc
flows because they arrive unexpected. Fix this by integrating the
invitations into the normal llc event flow and handle them as a flow.
While at it, check for already assigned requests in the flow before
the new add link request is assigned.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: 1f90a05d9f ("net/smc: add smcr_port_add() and smcr_link_up() processing")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be save from unexpected or late llc response messages check if the
arrived message fits to the current flow type and drop out-of-flow
messages. And drop it when there is already a response assigned to
the flow.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: ef79d439cd ("net/smc: process llc responses in tasklet context")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before an smc ib device is used the first time for an smc link it is
lazily initialized. When there are 2 active link groups and a new ib
device is brought online then it might happen that 2 link creations run
in parallel and enter smc_ib_setup_per_ibdev(). Both allocate new send
and receive completion queues on the device, but only one set of them
keeps assigned and the other leaks.
Fix that by protecting the setup and cleanup code using a mutex.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: f3c1deddb2 ("net/smc: separate function for link initialization")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For new rdma connections the SMC server assigns the link and sends the
link data in the clc accept message. To match the correct link use not
only the qp_num but also the gid and the mac of the links. If there are
equal qp_nums for different links the wrong link would be chosen.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: 0fb0b02bd6 ("net/smc: adapt SMC client code to use the LLC flow")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a link-down condition we notify the SMC server and expect that the
server will finally trigger the link clear processing on the client
side. This could fail when anything along this notification path goes
wrong. Clear the link as part of SMC client link-down processing to
prevent dangling links.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: 541afa10c1 ("net/smc: add smcr_port_err() and smcr_link_down() processing")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A delete link could arrive during confirm link processing. Handle this
situation directly in smc_llc_srv_conf_link() rather than using the
logic in smc_llc_wait() to avoid the unexpected message handling there.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: 1551c95b61 ("net/smc: final part of add link processing as SMC server")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
p9_read_work and p9_fd_cancelled may be called concurrently.
In some cases, req->req_list may be deleted by both p9_read_work
and p9_fd_cancelled.
We can fix it by ignoring replies associated with a cancelled
request and ignoring cancelled request if message has been received
before lock.
Link: http://lkml.kernel.org/r/20200612090833.36149-1-wanghai38@huawei.com
Fixes: 60ff779c4a ("9p: client: remove unused code and any reference to "cancelled" function")
Cc: <stable@vger.kernel.org> # v3.12+
Reported-by: syzbot+77a25acfa0382e06ab23@syzkaller.appspotmail.com
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
p9_fd_open just fgets file descriptors passed in from userspace, but
doesn't verify that they are valid for read or writing. This gets
cought down in the VFS when actually attempting a read or write, but
a new warning added in linux-next upsets syzcaller.
Fix this by just verifying the fds early on.
Link: http://lkml.kernel.org/r/20200710085722.435850-1-hch@lst.de
Reported-by: syzbot+e6f77e16ff68b2434a2c@syzkaller.appspotmail.com
Signed-off-by: Christoph Hellwig <hch@lst.de>
[Dominique: amend goto as per Doug Nazar's review]
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
Same as for udp4, let BPF program override the socket lookup result, by
selecting a receiving socket of its choice or failing the lookup, if no
connected UDP socket matched packet 4-tuple.
Suggested-by: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200717103536.397595-11-jakub@cloudflare.com
Prepare for calling into reuseport from __udp6_lib_lookup as well.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200717103536.397595-10-jakub@cloudflare.com
Following INET/TCP socket lookup changes, modify UDP socket lookup to let
BPF program select a receiving socket before searching for a socket by
destination address and port as usual.
Lookup of connected sockets that match packet 4-tuple is unaffected by this
change. BPF program runs, and potentially overrides the lookup result, only
if a 4-tuple match was not found.
Suggested-by: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200717103536.397595-9-jakub@cloudflare.com
Prepare for calling into reuseport from __udp4_lib_lookup as well.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200717103536.397595-8-jakub@cloudflare.com
Following ipv4 stack changes, run a BPF program attached to netns before
looking up a listening socket. Program can return a listening socket to use
as result of socket lookup, fail the lookup, or take no action.
Suggested-by: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200717103536.397595-7-jakub@cloudflare.com
Prepare for calling into reuseport from inet6_lookup_listener as well.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200717103536.397595-6-jakub@cloudflare.com
Run a BPF program before looking up a listening socket on the receive path.
Program selects a listening socket to yield as result of socket lookup by
calling bpf_sk_assign() helper and returning SK_PASS code. Program can
revert its decision by assigning a NULL socket with bpf_sk_assign().
Alternatively, BPF program can also fail the lookup by returning with
SK_DROP, or let the lookup continue as usual with SK_PASS on return, when
no socket has been selected with bpf_sk_assign().
This lets the user match packets with listening sockets freely at the last
possible point on the receive path, where we know that packets are destined
for local delivery after undergoing policing, filtering, and routing.
With BPF code selecting the socket, directing packets destined to an IP
range or to a port range to a single socket becomes possible.
In case multiple programs are attached, they are run in series in the order
in which they were attached. The end result is determined from return codes
of all the programs according to following rules:
1. If any program returned SK_PASS and selected a valid socket, the socket
is used as result of socket lookup.
2. If more than one program returned SK_PASS and selected a socket,
last selection takes effect.
3. If any program returned SK_DROP, and no program returned SK_PASS and
selected a socket, socket lookup fails with -ECONNREFUSED.
4. If all programs returned SK_PASS and none of them selected a socket,
socket lookup continues to htable-based lookup.
Suggested-by: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200717103536.397595-5-jakub@cloudflare.com
Prepare for calling into reuseport from __inet_lookup_listener as well.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200717103536.397595-4-jakub@cloudflare.com
Add a new program type BPF_PROG_TYPE_SK_LOOKUP with a dedicated attach type
BPF_SK_LOOKUP. The new program kind is to be invoked by the transport layer
when looking up a listening socket for a new connection request for
connection oriented protocols, or when looking up an unconnected socket for
a packet for connection-less protocols.
When called, SK_LOOKUP BPF program can select a socket that will receive
the packet. This serves as a mechanism to overcome the limits of what
bind() API allows to express. Two use-cases driving this work are:
(1) steer packets destined to an IP range, on fixed port to a socket
192.0.2.0/24, port 80 -> NGINX socket
(2) steer packets destined to an IP address, on any port to a socket
198.51.100.1, any port -> L7 proxy socket
In its run-time context program receives information about the packet that
triggered the socket lookup. Namely IP version, L4 protocol identifier, and
address 4-tuple. Context can be further extended to include ingress
interface identifier.
To select a socket BPF program fetches it from a map holding socket
references, like SOCKMAP or SOCKHASH, and calls bpf_sk_assign(ctx, sk, ...)
helper to record the selection. Transport layer then uses the selected
socket as a result of socket lookup.
In its basic form, SK_LOOKUP acts as a filter and hence must return either
SK_PASS or SK_DROP. If the program returns with SK_PASS, transport should
look for a socket to receive the packet, or use the one selected by the
program if available, while SK_DROP informs the transport layer that the
lookup should fail.
This patch only enables the user to attach an SK_LOOKUP program to a
network namespace. Subsequent patches hook it up to run on local delivery
path in ipv4 and ipv6 stacks.
Suggested-by: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200717103536.397595-3-jakub@cloudflare.com
Validate MAC address before copying the same to outgoing frame
skb destination address. Since a node can have zero mac
address for Link B until a valid frame is received over
that link, this fix address the issue of a zero MAC address
being in the packet.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For small Ethernet frames with size less than minimum size 66 for HSR
vs 60 for regular Ethernet frames, hsr driver currently doesn't pad the
frame to make it minimum size. This results in incorrect LSDU size being
populated in the HSR tag for these frames. Fix this by padding the frame
to the minimum size applicable for HSR.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When nfc_register_device fails in nci_register_device,
destroy_workqueue() shouled be called to destroy ndev->tx_wq.
Fixes: 3c1c0f5dc8 ("NFC: NCI: Fix nci_register_device init sequence")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two existing SNMP counters, TCPDSACKRecv and TCPDSACKOfoRecv,
which are incremented depending on whether the DSACKed range is below
the cumulative ACK sequence number or not. Unfortunately, these both
implicitly assume each DSACK covers only one segment. This makes these
counters unusable for estimating spurious retransmit rates,
or real/non-spurious loss rate.
This patch introduces a new SNMP counter, TCPDSACKRecvSegs, which tracks
the estimated number of duplicate segments based on:
(DSACKed sequence range) / MSS. This counter is usable for estimating
spurious retransmit rates, or real/non-spurious loss rate.
Signed-off-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, while processing DSACK, we assume DSACK covers only one
segment. This leads to significant underestimation of DSACKs with
LRO/GRO. This patch fixes segment accounting with DSACK by estimating
segment count from DSACK sequence range / MSS.
Signed-off-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yousuk Seung <ysseung@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
since commit d47a721520 ("mptcp: fix race in subflow_data_ready()"), it
is possible to observe a regression in MP_JOIN kselftests. For sockets in
TCP_CLOSE state, it's not sufficient to just wake up the main socket: we
also need to ensure that received data are made available to the reader.
Silence the WARN_ON_ONCE() in these cases: it preserves the syzkaller fix
and restores kselftests when they are ran as follows:
# while true; do
> make KBUILD_OUTPUT=/tmp/kselftest TARGETS=net/mptcp kselftest
> done
Reported-by: Florian Westphal <fw@strlen.de>
Fixes: d47a721520 ("mptcp: fix race in subflow_data_ready()")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/47
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reorders the masks array every 4 seconds based on their
usage count. This greatly reduces the masks per packet hit, and
hence the overall performance. Especially in the OVS/OVN case for
OpenShift.
Here are some results from the OVS/OVN OpenShift test, which use
8 pods, each pod having 512 uperf connections, each connection
sends a 64-byte request and gets a 1024-byte response (TCP).
All uperf clients are on 1 worker node while all uperf servers are
on the other worker node.
Kernel without this patch : 7.71 Gbps
Kernel with this patch applied: 14.52 Gbps
We also run some tests to verify the rebalance activity does not
lower the flow insertion rate, which does not.
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Tested-by: Andrew Theurer <atheurer@redhat.com>
Reviewed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Better to unregister the file system before destroying the kmem_cache
cache of the inodes, so that the inodes are freed before we are trying
to destroy it. Otherwise, kmem_cache yells that some objects are live.
Signed-off-by: Dan Aloni <dan@kernelim.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Naresh reported some compile errors:
arm build failed due this error on linux-next 20200713 and 20200713
net/ipv6/ip6_vti.o: In function `vti6_rcv_tunnel':
ip6_vti.c:(.text+0x1d20): undefined reference to `xfrm6_tunnel_spi_lookup'
This happened when set CONFIG_IPV6_VTI=y and CONFIG_INET6_TUNNEL=m.
We don't really want ip6_vti to depend inet6_tunnel completely, but
only to disable the tunnel code when inet6_tunnel is not seen.
So instead of adding "select INET6_TUNNEL" for IPV6_VTI, this patch
is only to change to IS_REACHABLE to avoid these compile error.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Fixes: 08622869ed ("ip6_vti: support IP6IP6 tunnel processing with .cb_handler")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
kernel test robot reported some compile errors:
ia64-linux-ld: net/xfrm/xfrm_interface.o: in function `xfrmi4_fini':
net/xfrm/xfrm_interface.c:900: undefined reference to `xfrm4_tunnel_deregister'
ia64-linux-ld: net/xfrm/xfrm_interface.c:901: undefined reference to `xfrm4_tunnel_deregister'
ia64-linux-ld: net/xfrm/xfrm_interface.o: in function `xfrmi4_init':
net/xfrm/xfrm_interface.c:873: undefined reference to `xfrm4_tunnel_register'
ia64-linux-ld: net/xfrm/xfrm_interface.c:876: undefined reference to `xfrm4_tunnel_register'
ia64-linux-ld: net/xfrm/xfrm_interface.c:885: undefined reference to `xfrm4_tunnel_deregister'
This happened when set CONFIG_XFRM_INTERFACE=y and CONFIG_INET_TUNNEL=m.
We don't really want xfrm_interface to depend inet_tunnel completely,
but only to disable the tunnel code when inet_tunnel is not seen.
So instead of adding "select INET_TUNNEL" for XFRM_INTERFACE, this patch
is only to change to IS_REACHABLE to avoid these compile error.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: da9bbf0598 ("xfrm: interface: support IPIP and IPIP6 tunnels processing with .cb_handler")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
In case we're compiling espintcp support only for IPv6, we should
still initialize the common code.
Fixes: 26333c37fc ("xfrm: add IPv6 support for espintcp")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
man 2 recv says:
RETURN VALUE
When a stream socket peer has performed an orderly shutdown, the
return value will be 0 (the traditional "end-of-file" return).
Currently, this works for blocking reads, but non-blocking reads will
return -EAGAIN. This patch overwrites that return value when the peer
won't send us any more data.
Fixes: e27cca96cd ("xfrm: add espintcp (RFC 8229)")
Reported-by: Andrew Cagney <cagney@libreswan.org>
Tested-by: Andrew Cagney <cagney@libreswan.org>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Currently, non-blocking sends from userspace result in EOPNOTSUPP.
To support this, we need to tell espintcp_sendskb_locked() and
espintcp_sendskmsg_locked() that non-blocking operation was requested
from espintcp_sendmsg().
Fixes: e27cca96cd ("xfrm: add espintcp (RFC 8229)")
Reported-by: Andrew Cagney <cagney@libreswan.org>
Tested-by: Andrew Cagney <cagney@libreswan.org>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Mirred currently does not mix well with blocks executed after the qdisc
root lock is taken. This includes classification blocks (such as in PRIO,
ETS, DRR qdiscs) and qevents. The locking caused by the packet mirrored by
mirred can cause deadlocks: either when the thread of execution attempts to
take the lock a second time, or when two threads end up waiting on each
other's locks.
The qevent patchset attempted to not introduce further badness of this
sort, and dropped the lock before executing the qevent block. However this
lead to too little locking and races between qdisc configuration and packet
enqueue in the RED qdisc.
Before the deadlock issues are solved in a way that can be applied across
many qdiscs reasonably easily, do for qevents what is done for the
classification blocks and just keep holding the root lock.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
A busy-wait loop is used to implement waiting for bits to be copied
from the skb to the kernel buffer before retiring a block. This is
a problem on PREEMPT_RT because the copying task could be preempted
by the busy-waiting task and thus live lock in the busy-wait loop.
Replace the busy-wait logic with an rwlock_t. This provides lockdep
coverage and makes the code RT ready.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce the capability to attach an eBPF program to cpumap entries.
The idea behind this feature is to add the possibility to define on
which CPU run the eBPF program if the underlying hw does not support
RSS. Current supported verdicts are XDP_DROP and XDP_PASS.
This patch has been tested on Marvell ESPRESSObin using xdp_redirect_cpu
sample available in the kernel tree to identify possible performance
regressions. Results show there are no observable differences in
packet-per-second:
$./xdp_redirect_cpu --progname xdp_cpu_map0 --dev eth0 --cpu 1
rx: 354.8 Kpps
rx: 356.0 Kpps
rx: 356.8 Kpps
rx: 356.3 Kpps
rx: 356.6 Kpps
rx: 356.6 Kpps
rx: 356.7 Kpps
rx: 355.8 Kpps
rx: 356.8 Kpps
rx: 356.8 Kpps
Co-developed-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/5c9febdf903d810b3415732e5cd98491d7d9067a.1594734381.git.lorenzo@kernel.org
Now that there's a function that calculates the SHA-256 digest of a
buffer in one step, use it instead of sha256_init() + sha256_update() +
sha256_final().
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Cc: mptcp@lists.01.org
Cc: Mat Martineau <mathew.j.martineau@linux.intel.com>
Cc: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Remove the unnecessary label from dn_dev_ioctl() and make its error
handling simpler to read.
Signed-off-by: Suraj Upadhyay <usuraj35@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The nf_tables_rule_release() function frees "rule" so we have to use
the _safe() version of list_for_each_entry().
Fixes: d0e2c7de92 ("netfilter: nf_tables: add NFT_CHAIN_BINDING")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
sybot came up with following transaction:
add table ip syz0
add chain ip syz0 syz2 { type nat hook prerouting priority 0; policy accept; }
add table ip syz0 { flags dormant; }
delete chain ip syz0 syz2
delete table ip syz0
which yields:
hook not found, pf 2 num 0
WARNING: CPU: 0 PID: 6775 at net/netfilter/core.c:413 __nf_unregister_net_hook+0x3e6/0x4a0 net/netfilter/core.c:413
[..]
nft_unregister_basechain_hooks net/netfilter/nf_tables_api.c:206 [inline]
nft_table_disable net/netfilter/nf_tables_api.c:835 [inline]
nf_tables_table_disable net/netfilter/nf_tables_api.c:868 [inline]
nf_tables_commit+0x32d3/0x4d70 net/netfilter/nf_tables_api.c:7550
nfnetlink_rcv_batch net/netfilter/nfnetlink.c:486 [inline]
nfnetlink_rcv_skb_batch net/netfilter/nfnetlink.c:544 [inline]
nfnetlink_rcv+0x14a5/0x1e50 net/netfilter/nfnetlink.c:562
netlink_unicast_kernel net/netlink/af_netlink.c:1303 [inline]
Problem is that when I added ability to override base hook registration
to make nat basechains register with the nat core instead of netfilter
core, I forgot to update nft_table_disable() to use that instead of
the 'raw' hook register interface.
In syzbot transaction, the basechain is of 'nat' type. Its registered
with the nat core. The switch to 'dormant mode' attempts to delete from
netfilter core instead.
After updating nft_table_disable/enable to use the correct helper,
nft_(un)register_basechain_hooks can be folded into the only remaining
caller.
Because nft_trans_table_enable() won't do anything when the DORMANT flag
is set, remove the flag first, then re-add it in case re-enablement
fails, else this patch breaks sequence:
add table ip x { flags dormant; }
/* add base chains */
add table ip x
The last 'add' will remove the dormant flags, but won't have any other
effect -- base chains are not registered.
Then, next 'set dormant flag' will create another 'hook not found'
splat.
Reported-by: syzbot+2570f2c036e3da5db176@syzkaller.appspotmail.com
Fixes: 4e25ceb80b ("netfilter: nf_tables: allow chain type to override hook register")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently the header size calculations are using an assignment
operator instead of a += operator when accumulating the header
size leading to incorrect sizes. Fix this by using the correct
operator.
Addresses-Coverity: ("Unused value")
Fixes: 302d3deb20 ("xprtrdma: Prevent inline overflow")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Sabrina Dubroca