With a postfix increment, i is incremented one past 10K/5K before the
loop ends, so the error messages will be displayed too soon if the
test succeeds on the last iteration. Fix the comparisons to be >
instead of >=.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
With updated PHY firmware for SFP_D, setting the trace length to 1
inch for SFP_D provides a more stable link.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Enable repause timer for port 1. Without this setting, under stress,
the chip may misbehave.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In commit 1b949324 ("RDMA/nes: Fix SFP+ PHY initialization") there is
a mistake in the clean up code that removed port 1 CDR loop filter
settings for 10G cards other than CX4. Put the correct setting back
for appropriate PHY types.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change thermo mitigation code to flip the SerDes1 reference clock to
internal, to match the change in commit a4849fc1 ("RDMA/nes: Add
wide_ppm_offset parm for switch compatibility").
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add new register settings for new SFP+ PHY/firmware.
Add new PHY to to nes_netdev_get/set_settings.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We have observed unstable link with a new BNT switch.
Add wide_ppm_offset parameter to allow the user to control the clock
ppm offset on the CX4 interface for better compatibility. Default is
100ppm, setting it to 1 will increase it to 300ppm. Change default
SerDes1 reference clock to external source.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
SFP+ PHY initialization has very long delays, incorrect settings for
direct attach copper cables, and inconsistent link detection.
Adjust delays to the minimum required by the PHY. Worst case is now
less than 4 seconds. Add new register settings for direct attach
cables. Change link detection logic to use two new registers for more
consistent link state detection. Reorganize code to shorten line
length.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1750 commits)
ixgbe: Allow Priority Flow Control settings to survive a device reset
net: core: remove unneeded include in net/core/utils.c.
e1000e: update version number
e1000e: fix close interrupt race
e1000e: fix loss of multicast packets
e1000e: commonize tx cleanup routine to match e1000 & igb
netfilter: fix nf_logger name in ebt_ulog.
netfilter: fix warning in ebt_ulog init function.
netfilter: fix warning about invalid const usage
e1000: fix close race with interrupt
e1000: cleanup clean_tx_irq routine so that it completely cleans ring
e1000: fix tx hang detect logic and address dma mapping issues
bridge: bad error handling when adding invalid ether address
bonding: select current active slave when enslaving device for mode tlb and alb
gianfar: reallocate skb when headroom is not enough for fcb
Bump release date to 25Mar2009 and version to 0.22
r6040: Fix second PHY address
qeth: fix wait_event_timeout handling
qeth: check for completion of a running recovery
qeth: unregister MAC addresses during recovery.
...
Manually fixed up conflicts in:
drivers/infiniband/hw/cxgb3/cxio_hal.h
drivers/infiniband/hw/nes/nes_nic.c
NETIF_F_LLTX is deprecated. Remove private TX locking from the driver
and remove the NETIF_F_LLTX feature flag. This also fixes a warning
in some configs that comes from doing skb_linearize() call in the
hard_start_xmit method with IRQs disabled (if HIGHMEM is enabled,
skb_linearize() may end up enabling BHs, which is a no-no if hard IRQs
are disabled in that context). By getting rid of LLTX, we do not
disable IRQs when skb_linearize() is called.
Remove the sq_lock as it is not needed for non-LLTX. Fix ethtool not
to show the counter for sq_lock.
Reported-by: aluno3@poczta.onet.pl
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When asynchronous events are processed by software, it is necessary
to let the hardware know that software has handled the event. This
frees up the entry in the asynchronous event queue.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ibv_devinfo displays 0 for vendor_id and vendor_part_id. Fill in OUI
and device_id for those two fields.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Update copyright to the new legal entity, Intel-NE, Inc., an Intel
company. Update copyright for the new year.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
net: Allow dependancies of FDDI & Tokenring to be modular.
igb: Fix build warning when DCA is disabled.
net: Fix warning fallout from recent NAPI interface changes.
gro: Fix potential use after free
sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
sfc: When disabling the NIC, close the device rather than unregistering it
sfc: SFT9001: Add cable diagnostics
sfc: Add support for multiple PHY self-tests
sfc: Merge top-level functions for self-tests
sfc: Clean up PHY mode management in loopback self-test
sfc: Fix unreliable link detection in some loopback modes
sfc: Generate unique names for per-NIC workqueues
802.3ad: use standard ethhdr instead of ad_header
802.3ad: generalize out mac address initializer
802.3ad: initialize ports LACPDU from const initializer
802.3ad: remove typedef around ad_system
802.3ad: turn ports is_individual into a bool
802.3ad: turn ports is_enabled into a bool
802.3ad: make ntt bool
ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
...
Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter. This patch cleans up that api by
properly removing it..
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under heavy traffic, there is a small windows when an APBVT entry is
not yet removed and a new connection is established. Packets for the
new connection are dropped until APBVT entry is removed. This patch
will forward the packets instead of dropping them.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Mask off a critical error after 100 critical error interrupts to
keep the system "sane".
Signed-off-by: Sweta Bhatt <sweta.bhatt@einfochips.com>
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use timer value set via ethtool intead of #defines.
Signed-off-by: John Lacombe <jlacombe@neteffect.com>
Signed-off-by: Sweta Bhatt <sweta.bhatt@einfochips.com>
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Clear MDC bits before setting them to a new value. Adjust MDC value
for 10G.
Signed-off-by: Sweta Bhatt <sweta.bhatt@einfochips.com>
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a module parameter wqm_quanta. It controls the number of segments
transmitted at a time.
Signed-off-by: Sweta Bhatt <sweta.bhatt@einfochips.com>
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for NetEffect 4 port 1G HP blade card. The mapping
between physical port and MAC is different from the standup card.
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Major rework of CM connection setup/teardown. We had a number of issues
with MPI applications not starting/terminating properly over time.
With these changes we were able to run longer on larger clusters.
* Remove memory allocation from nes_connect() and nes_cm_connect().
* Fix mini_cm_dec_refcnt_listen() when destroying listener.
* Remove unnecessary code from schedule_nes_timer() and nes_cm_timer_tick().
* Functionalize mini_cm_recv_pkt() and process_packet().
* Clean up cm_node->ref_count usage.
* Reuse skbs if available.
Signed-off-by: Faisal Latif <flatif@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- Change the IB_DEVICE_ZERO_STAG flag to the transport-neutral name
IB_DEVICE_LOCAL_DMA_LKEY, which is used by iWARP RNICs to indicate 0
STag support and IB HCAs to indicate reserved L_Key support.
- Add a u32 local_dma_lkey member to struct ib_device. Drivers fill
this in with the appropriate local DMA L_Key (if they support it).
- Fix up the drivers using this flag.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Every caller of nes_post_cqp_request() passed it NES_CQP_REQUEST_RING_DOORBELL,
so just remove that parameter and always ring the doorbell.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Faisal Latif <flatif@neteffect.com>
Fix some bugs with the max_aggr module parameter added with LRO support:
- The module parameter value ignored and not actually used to set
lro_mgr.max_aggr.
- MODULE_PARM_DESC had a typo "_mro_" instead of "_lro_" so it didn't
end up describing the actual module parameter.
- The nes_lro_max_aggr variable was declared as unsigned, but the
module_param line said "int" instead of "uint" for the type.
- The default value for the parameter was stuck in the permissions
field of module_param, which led to nonsensical permissions for the
file under /sys/module/iw_nes/param.
- The parameter was used in only one file but defined in another, which
led to the variable being global for no good reason. Move everything
related to the parameter to the file nes_hw.c where it is actually
used.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Various cleanups:
- Change // to /* .. */
- Place whitespace around binary operators.
- Trim down a few long lines.
- Some minor alignment formatting for better readability.
- Remove some silly tabs.
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch enables the iw_nes module for NetEffect RNICs to support
additional PHYs including SFP+ (referred to as ARGUS in the code).
Signed-off-by: Eric Schneider <eric.schneider@neteffect.com>
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
After PXE boot, the iw_nes driver does a full reset to ensure the card
is in a clean state. However, it doesn't wait for firmware to
complete its work before issuing a port reset to enable the ports,
which leads to problems bringing up the ports.
The solution is to wait for firmware to complete its work before
proceeding with port reset.
This bug was flagged by Roland Dreier <rolandd@cisco.com>.
Cc: <stable@kernel.org>
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a new IB_WR_SEND_WITH_INV send opcode that can be used to mark a
"send with invalidate" work request as defined in the iWARP verbs and
the InfiniBand base memory management extensions. Also put "imm_data"
and a new "invalidate_rkey" member in a new "ex" union in struct
ib_send_wr. The invalidate_rkey member can be used to pass in an
R_Key/STag to be invalidated. Add this new union to struct
ib_uverbs_send_wr. Add code to copy the invalidate_rkey field in
ib_uverbs_post_send().
Fix up low-level drivers to deal with the change to struct ib_send_wr,
and just remove the imm_data initialization from net/sunrpc/xprtrdma/,
since that code never does any send with immediate operations.
Also, move the existing IB_DEVICE_SEND_W_INV flag to a new bit, since
the iWARP drivers currently in the tree set the bit. The amso1100
driver at least will silently fail to honor the IB_SEND_INVALIDATE bit
if passed in as part of userspace send requests (since it does not
implement kernel bypass work request queueing). Remove the flag from
all existing drivers that set it until we know which ones are OK.
The values chosen for the new flag is not consecutive to avoid clashing
with flags defined in the XRC patches, which are not merged yet but
which are already in use and are likely to be merged soon.
This resurrects a patch sent long ago by Mikkel Hagen <mhagen@iol.unh.edu>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
__FUNCTION__ is gcc-specific, use __func__ instead.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Interrupt moderation low threshold value was incorrectly triggering,
indicating that the threshold should be lowered.
The impact was the timer was likely to become 40usecs and get stuck
there. The biggest side effect was too many interrupts and nonoptimal
performance.
Signed-off-by: John Lacombe <jlacombe@neteffect.com>
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a standard NIC and RDMA/iWARP driver for NetEffect 1/10Gb ethernet adapters.
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Roel Kluin