Costantino Leandro found a bug in tty_find_polling_driver and provided a
patch that fixed the crash but not the underlying bug. This fixes the
underlying bug where the list walk corrupts the values it is using on a
match but then reuses them if the open fails.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We fixed the globals, so now fix the comment
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tty throttling code can race due to the lock drops. It takes very high
loads but this has been observed and verified by Rob Duncan.
The basic problem is that on an SMP box we can go
CPU #1 CPU #2
need to throttle ?
suppose we should buffer space cleared
are we throttled
yes ? - unthrottle
call throttle method
This changeet take the termios lock to protect against this. The termios
lock isn't the initial obvious candidate but many implementations of throttle
methods already need to poke around their own termios structures (and nobody
really locks them against a racing change of flow control).
This does mean that anyone who is setting tty->low_latency = 1 and then
calling tty_flip_buffer_push from their unthrottle method is going to end up
collapsing in a pile of locks. However we've removed all the known bogus
users of low_latency = 1 and such use isn't safe anyway for other reasons so
catching it would be an improvement.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The legacy TCSETA{,W,F} ioctls failed to set the termio->c_line field
on x86. This adds a missing get_user.
The same ioctls also fail to report faulting user pointers, which
we keep ignoring.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for the following serial controller chip:
Oxford Semiconductor OXCB950 for PCI Cardbus interface
http://www.transdimension.com/products/serial/OXCB950.html
on this card:
ExSys EX-1370 1 port high-speed serial card for ExpressCard/34 slot
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch from ASYNC_* to ASYNCB_*, because test_bit expects
bit number, not mask.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch from ASYNC_* to ASYNCB_*, because {test,set}_bit expect
bit number, not mask.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Define ASYNCB_* flags which are bit numbers of the ASYNC_* flags.
This is useful for {test,set,clear}_bit.
Also convert each ASYNC_% to be (1 << ASYNCB_%) and define masks
with the macros, not constants.
Tested with:
#include "PATH_TO_KERNEL/include/linux/serial.h"
static struct {
unsigned int new, old;
} as[] = {
{ ASYNC_HUP_NOTIFY, 0x0001 },
{ ASYNC_FOURPORT, 0x0002 },
...
{ ASYNC_BOOT_ONLYMCA, 0x00400000 },
{ ASYNC_INTERNAL_FLAGS, 0xFFC00000 }
};
...
for (a = 0; a < ARRAY_SIZE(as); a++)
if (as[a].old != as[a].new)
printf("%.8x != %.8x\n", as[a].old, as[a].new);
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Or at least most of it. There are further clean ups possible and there are
are also thing checkpatch moans about that would be silly to "fix".
Also note some FIXME points found as the cleanup was done.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now we have a port structure begin using the fields and kref counts
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Set up ports right after FW load so that we won't allocate maximal
(64) ports when we use few.
Also remove reading of nports in irq context, since we know it from
initialisation now.
This also fixes a tty ports unregistration on some fail paths and for
Ze which registered 64 and unregistered real port count.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove ugly macros and add inlines instead of them. This improves
readability and type checking a much.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Store HW version locally to not read it all the time in interrupts
and alike.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove ugly all-over-the-code casts of ctl_addr to 9060 space.
Add an union to the cyclades_card structure, which contains
a pointer to both 9050 and 9060 spaces.
The 9050 space layout is unknown, so let it still as a void
__iomem pointer.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add receive programmed IO mode to reduce receive latency
when using low data rates. The receive FIFO trigger
level of 128 bytes used in DMA mode creates excessive latency
when operating at low data rates. PIO mode is selected when user
application requests data in blocks of less than 128 bytes.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The CDC ACM driver uses the tty layer correctly so needs conversion. Start by
adding and initializing the port structures.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows us to clean stuff up, but is probably also going to cause
some app breakage with buggy apps as we now implement proper POSIX behaviour
for USB ports matching all the other ports. This does also mean other apps
that break on USB will now work properly.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need this for devices that cannot flush and wait, but which do not order
data and modem events. Without it we will hang up before all the data
clears the hardware. Needed for the USB changes.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some drivers implement this internally, others miss it out. Push the
behaviour into the core code as that way everyone will do it consistently.
Update the dtr rts method to raise or lower depending upon flags. Having a
single method in this style fits most of the implementations more cleanly than
two funtions.
We need this in place before we tackle the USB side
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No need to check if dev_id is NULL, it never is.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't reset the PLX chip after FW load, which effectively kills
the FW, so that user had to boot manually.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ze needs firmware to be loaded as well as Zo. Move cyz_load_fw one
level upper to achieve that.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's a bug in the mxser kernel module that still appears in the
2.6.29.4 kernel.
mxser_get_ISA_conf takes a ioaddress as its first argument, by passing the
not of the ioaddr, you're effectively passing 0 which means it won't be
able to talk to an ISA card. I have tested this, and removing the !
fixes the problem.
Cc: "Peter Botha" <peterb@goldcircle.co.za>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit code, we scan buffers attached to a transaction. During this
scan, we sometimes have to drop j_list_lock and then we recheck whether
the journal buffer head didn't get freed by journal_try_to_free_buffers().
But checking for buffer_jbd(bh) isn't enough because a new journal head
could get attached to our buffer head. So add a check whether the journal
head remained the same and whether it's still at the same transaction and
list.
This is a nasty bug and can cause problems like memory corruption (use after
free) or trigger various assertions in JBD code (observed).
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: <stable@kernel.org>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The recent ->lookup() deadlock correction required the directory inode
mutex to be dropped while waiting for expire completion. We were
concerned about side effects from this change and one has been identified.
I saw several error messages.
They cause autofs to become quite confused and don't really point to the
actual problem.
Things like:
handle_packet_missing_direct:1376: can't find map entry for (43,1827932)
which is usually totally fatal (although in this case it wouldn't be
except that I treat is as such because it normally is).
do_mount_direct: direct trigger not valid or already mounted
/test/nested/g3c/s1/ss1
which is recoverable, however if this problem is at play it can cause
autofs to become quite confused as to the dependencies in the mount tree
because mount triggers end up mounted multiple times. It's hard to
accurately check for this over mounting case and automount shouldn't need
to if the kernel module is doing its job.
There was one other message, similar in consequence of this last one but I
can't locate a log example just now.
When checking if a mount has already completed prior to adding a new mount
request to the wait queue we check if the dentry is hashed and, if so, if
it is a mount point. But, if a mount successfully completed while we
slept on the wait queue mutex the dentry must exist for the mount to have
completed so the test is not really needed.
Mounts can also be done on top of a global root dentry, so for the above
case, where a mount request completes and the wait queue entry has already
been removed, the hashed test returning false can cause an incorrect
callback to the daemon. Also, d_mountpoint() is not sufficient to check
if a mount has completed for the multi-mount case when we don't have a
real mount at the base of the tree.
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The massive nommu update (8feae131) resulted in these warnings:
ipc/shm.c: In function `sys_shmdt':
ipc/shm.c:974: warning: unused variable `size'
ipc/shm.c:972: warning: unused variable `next'
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
cls_cgroup: Fix oops when user send improperly 'tc filter add' request
r8169: fix crash when large packets are received
* 'for-linus' of git://neil.brown.name/md:
md/raid5: fix bug in reshape code when chunk_size decreases.
md/raid5 - avoid deadlocks in get_active_stripe during reshape
md/raid5: use conf->raid_disks in preference to mddev->raid_disk
Due to commit 1cd96c242a ("block: WARN
in __blk_put_request() for potential bio leak"), BSG SMP requests get
the false warnings:
WARNING: at block/blk-core.c:1068 __blk_put_request+0x52/0xc0()
This sets rq->bio to NULL to avoid that false warnings.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
These are defined as static cpumask_var_t so if MAXSMP is not used,
they are cleared already. Avoid surprises when MAXSMP is enabled.
Signed-off-by: Yinghai Lu <yinghai.lu@kernel.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
I found a bug in cls_cgroup_change() in cls_cgroup.c.
cls_cgroup_change() expected tca[TCA_OPTIONS] was set from user space properly,
but tc in iproute2-2.6.29-1 (which I used) didn't set it.
In the current source code of tc in git, it set tca[TCA_OPTIONS].
git://git.kernel.org/pub/scm/linux/kernel/git/shemminger/iproute2.git
If we always use a newest iproute2 in git when we use cls_cgroup,
we don't face this oops probably.
But I think, kernel shouldn't panic regardless of use program's behaviour.
Signed-off-by: Minoru Usui <usui@mxm.nes.nec.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Tokarev reported receiving a large packet could crash
a machine with RTL8169 NIC.
( original thread at http://lkml.org/lkml/2009/6/8/192 )
Problem is this driver tells that NIC frames up to 16383 bytes
can be received but provides skb to rx ring allocated with
smaller sizes (1536 bytes in case standard 1500 bytes MTU is used)
When a frame larger than what was allocated by driver is received,
dma transfert can occurs past the end of buffer and corrupt
kernel memory.
Fix is to tell to NIC what is the maximum size a frame can be.
This bug is very old, (before git introduction, linux-2.6.10), and
should be backported to stable versions.
Reported-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we support changing the chunksize, we calculate
"reshape_sectors" to be the max of number of sectors in old
and new chunk size.
However there is one please where we still use 'chunksize'
rather than 'reshape_sectors'.
This causes a reshape that reduces the size of chunks to freeze.
Signed-off-by: NeilBrown <neilb@suse.de>
md has functionality to 'quiesce' and array so that all pending
IO completed and no new IO starts. This is used to achieve a
stable state before making internal changes.
Currently this quiescing applies equally to normal IO, resync
IO, and reshape IO.
However there is a problem with applying it to reshape IO.
Reshape can have multiple 'stripe_heads' that must be active together.
If the quiesce come between allocating the first and the last of
such a collection, then we deadlock, as the last will not be allocated
until the quiesce is lifted, the quiesce will not be lifted until the
first (which has been allocated) gets used, and that first cannot be
used until the last is allocated.
It is not necessary to inhibit reshape IO when a quiesce is
requested. Those places in the code that require a full quiesce will
ensure the reshape thread is not running at all.
So allow reshape requests to get access to new stripe_heads without
being blocked by a 'quiesce'.
This only affects in-place reshapes (i.e. where the array does not
grow or shrink) and these are only newly supported. So this patch is
not needed in earlier kernels.
Signed-off-by: NeilBrown <neilb@suse.de>
mddev->raid_disks can be changed and any time by a request from
user-space. It is a suggestion as to what number of raid_disks is
desired.
conf->raid_disks can only be changed by the raid5 module with suitable
locks in place. It is a statement as to the current number of
raid_disks.
There are two places where the latter should be used, but the former
is used. This can lead to a crash when reshaping an array.
This patch changes to mddev-> to conf->
Signed-off-by: NeilBrown <neilb@suse.de>
Our async work synchronization was broken by "async: make sure
independent async domains can't accidentally entangle" (commit
d5a877e8dd), because it would report
the wrong lowest active async ID when there was both running and
pending async work.
This caused things like no being able to read the root filesystem,
resulting in missing console devices and inability to run 'init',
causing a boot-time panic.
This fixes it by properly returning the lowest pending async ID: if
there is any running async work, that will have a lower ID than any
pending work, and we should _not_ look at the pending work list.
There were alternative patches from Jaswinder and James, but this one
also cleans up the code by removing the pointless 'ret' variable and
the unnecesary testing for an empty list around 'for_each_entry()' (if
the list is empty, the for_each_entry() thing just won't execute).
Fixes-bug: http://bugzilla.kernel.org/show_bug.cgi?id=13474
Reported-and-tested-by: Chris Clayton <chris2553@googlemail.com>
Cc: Jaswinder Singh Rajput <jaswinder@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: Outline udelay and fix a few issues.
MIPS: ioctl.h: Fix headers_check warnings
MIPS: Cobalt: PCI bus is always required to obtain the board ID
MIPS: Kconfig: Remove "Support for" from Cavium system type
MIPS: Sibyte: Honor CONFIG_CMDLINE
SSB: BCM47xx: Export ssb_watchdog_timer_set
The previous patch submission had a I typo I didn't catch but Bartlomiej
noted. Guess this proves the point about any patch being risky late in an rc
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Outlining fixes the issue were on certain CPUs such as the R10000 family
the delay loop would need an extra cycle if it overlaps a cacheline
boundary.
The rewrite also fixes build errors with GCC 4.4 which was changed in
way incompatible with the kernel's inline assembly.
Relying on pure C for computation of the delay value removes the need for
explicit. The price we pay is a slight slowdown of the computation - to
be fixed on another day.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make ioctl.h compatible with asm-generic/ioctl.h and userspace
fix the following 'make headers_check' warning:
usr/include/asm-mips/ioctl.h:64: extern's make no sense in userspace
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Alan Cox