Based on USB2.0 Spec Section 11.12.5,
"If a hub has per-port power switching and per-port current limiting,
an over-current on one port may still cause the power on another port
to fall below specific minimums. In this case, the affected port is
placed in the Power-Off state and C_PORT_OVER_CURRENT is set for the
port, but PORT_OVER_CURRENT is not set."
so let's check C_PORT_OVER_CURRENT too for over current condition.
Fixes: 08d1dec6f4 ("usb:hub set hub->change_bits when over-current happens")
Cc: <stable@vger.kernel.org>
Tested-by: Alessandro Antenucci <antenucci@korg.it>
Signed-off-by: Bin Liu <b-liu@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
add USBTMC_IOCTL_CONFIG_TERMCHAR to control TermChar handling
for next read(). Controls field 'TermChar' and Bit 1 of field
'bmTransferAttributes' of REQUEST_DEV_DEP_MSG_IN BULK-OUT header.
Allows enabling/disabling of terminating a read on reception of
term_char individually for each read request.
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Tested-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
add USBTMC_IOCTL_EOM_ENABLE to specify EOM bit for next write()
call. Sets Bit 0 of field 'bmTransferAttributes' of DEV_DEP_MSG_OUT
Bulk-OUT Header.
Allows fine grained control over end of message handling on a
per file descriptor basis.
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Tested-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
add USBTMC488_IOCTL_TRIGGER to send TRIGGER Bulk-OUT header
according to Subclass USB488 Specification
The usbtmc trigger command is equivalent to the IEEE 488 GET (Group
Execute Trigger) action. While the "*TRG" command can be sent as
data to perform the same operation, in some situations an instrument
will be busy and unable to process the data immediately in which
case the USBTMC488_IOCTL_TRIGGER can be used to trigger the
instrument with lower latency.
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Tested-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add ioctls USBTMC_IOCTL_GET_TIMEOUT / USBTMC_IOCTL_SET_TIMEOUT to
get/set I/O timeout for specific file handle.
Different operations on an instrument can take different lengths of
time thus it is important to be able to set the timeout slightly
longer than the expected duration of each operation to optimise the
responsiveness of the application. As the instrument may be shared by
multiple applications the timeout should be settable on a per file
descriptor basis.
Tested-by: Dave Penkler <dpenkler@gmail.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- use consistent error value ETIMEOUT instead of ETIME
Tested-by: Dave Penkler <dpenkler@gmail.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add 'struct usbtmc_file_data' for each file handle to cache last
srq_byte (=Status Byte with SRQ) received by usbtmc_interrupt(..)
usbtmc488_ioctl_read_stb returns cached srq_byte when available for
each file handle to avoid race conditions of concurrent applications.
SRQ now sets EPOLLPRI instead of EPOLLIN since EPOLLIN is now reserved
for asynchronous reads
Tested-by: Dave Penkler <dpenkler@gmail.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix build errors when built for PPC64:
These variables are only used on PPC32 so they don't need to be
initialized for PPC64.
../drivers/usb/phy/phy-fsl-usb.c: In function 'usb_otg_start':
../drivers/usb/phy/phy-fsl-usb.c:865:3: error: '_fsl_readl' undeclared (first use in this function); did you mean 'fsl_readl'?
_fsl_readl = _fsl_readl_be;
../drivers/usb/phy/phy-fsl-usb.c:865:16: error: '_fsl_readl_be' undeclared (first use in this function); did you mean 'fsl_readl'?
_fsl_readl = _fsl_readl_be;
../drivers/usb/phy/phy-fsl-usb.c:866:3: error: '_fsl_writel' undeclared (first use in this function); did you mean 'fsl_writel'?
_fsl_writel = _fsl_writel_be;
../drivers/usb/phy/phy-fsl-usb.c:866:17: error: '_fsl_writel_be' undeclared (first use in this function); did you mean 'fsl_writel'?
_fsl_writel = _fsl_writel_be;
../drivers/usb/phy/phy-fsl-usb.c:868:16: error: '_fsl_readl_le' undeclared (first use in this function); did you mean 'fsl_readl'?
_fsl_readl = _fsl_readl_le;
../drivers/usb/phy/phy-fsl-usb.c:869:17: error: '_fsl_writel_le' undeclared (first use in this function); did you mean 'fsl_writel'?
_fsl_writel = _fsl_writel_le;
and the sysfs "show" function return type should be ssize_t, not int:
../drivers/usb/phy/phy-fsl-usb.c:1042:49: error: initialization of 'ssize_t (*)(struct device *, struct device_attribute *, char *)' {aka 'long int (*)(struct device *, struct device_attribute *, char *)'} from incompatible pointer type 'int (*)(struct device *, struct device_attribute *, char *)' [-Werror=incompatible-pointer-types]
static DEVICE_ATTR(fsl_usb2_otg_state, S_IRUGO, show_fsl_usb2_otg_state, NULL);
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: linux-usb@vger.kernel.org
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 4.19-rc1, including:
- gpio support for CP2102N devices
- improved line-speed handling for cp210x
- conversion to spin_lock_irqsave() in completion handlers
- dropped kl5kusb105 support from the kl5kusb105 driver (sic!)
Included are also various lower-priority fixes and clean ups.
All but the final commit have been in linux-next, and with no reported
issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=0ukW
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.19-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.19-rc1
Here are the USB-serial updates for 4.19-rc1, including:
- gpio support for CP2102N devices
- improved line-speed handling for cp210x
- conversion to spin_lock_irqsave() in completion handlers
- dropped kl5kusb105 support from the kl5kusb105 driver (sic!)
Included are also various lower-priority fixes and clean ups.
All but the final commit have been in linux-next, and with no reported
issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch adds GPIO support for CP2102N devices.
It introduces new generic code to support emulating separate
input and outputs directions even though these devices
only know output modes (open-drain and pushpull). Existing
GPIO support for CP2105 has been migrated over to the new
code structure.
Only limitation is that for the QFN28 variant, only 4 out of
7 GPIOs are supported. This is because the config array
locations of the last 3 pins are not documented, and reverse
engineering revealed offsets that conflicted with other
documented functions. Hence we'll play it safe instead
until somebody clears this up further.
Signed-off-by: Karoly Pados <pados@pados.hu>
[ johan: fix style issues and a couple of minor bugs; use Karoly's
updated commit message ]
Acked-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
If td_list is not empty the cfg_cmd will not be freed,
call xhci_free_command to free it.
Signed-off-by: Zheng Xiaowei <zhengxiaowei@ruijie.com.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a bug in the sink PDO search code when trying to select
a PPS APDO. The current code actually sets the starting index for
searching to whatever value 'i' is, rather than choosing index 1
to avoid the first PDO (always 5V fixed). As a result, for sources
which support PPS but whose PPS APDO index does not match with the
supporting sink PPS APDO index for the platform, no valid PPS APDO
will be found so this feature will not be permitted.
Sadly in testing, both Source and Sink capabilities matched up and
this was missed. Code is now updated to correctly set the start
index to 1, and testing with additional PPS capable sources show
this to work as expected.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Fixes: 2eadc33f40 ("typec: tcpm: Add core support for sink side PPS")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 1b9ba000 ("Allow function drivers to pause control
transfers") states that USB_GADGET_DELAYED_STATUS is only
supported if data phase is 0 bytes.
It seems that when the length is not 0 bytes, there is no
need to explicitly delay the data stage since the transfer
is not completed until the user responds. However, when the
length is 0, there is no data stage and the transfer is
finished once setup() returns, hence there is a need to
explicitly delay completion.
This manifests as the following bugs:
Prior to 946ef68ad4 ('Let setup() return
USB_GADGET_DELAYED_STATUS'), when setup is 0 bytes, ffs
would require user to queue a 0 byte request in order to
clear setup state. However, that 0 byte request was actually
not needed and would hang and cause errors in other setup
requests.
After the above commit, 0 byte setups work since the gadget
now accepts empty queues to ep0 to clear the delay, but all
other setups hang.
Fixes: 946ef68ad4 ("Let setup() return USB_GADGET_DELAYED_STATUS")
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the coherent_dma_mask for the PS3 ehci, ohci, and snd devices.
Silences WARN_ON_ONCE messages emitted by the dma_alloc_attrs() routine.
Reported-by: Fredrik Noring <noring@nocrew.org>
Signed-off-by: Geoff Levand <geoff@infradead.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
CP2104 and the ECI interface of CP2105 support further baud rates than
the ones specified in AN205 table 1, and we can use the same equations
as for CP2102N to determine and report back the actual baud rates used.
Note that this could eventually be generalised also to CP2108, which
uses a different base clock. There appears to be an error in the CP2108
equations which needs to be confirmed on actual hardware first however
(specifically, the subtraction of one from the divisor appears to be
incorrect as it introduces larger errors).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The CP2102N equations for determining the actual baud rate can be used
also for other device types, so let's factor it out.
Note that this removes the now unused cp210x_is_cp2102n() helper.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
CP2102N devices support a lot more baudrates than earlier chips by
SiLabs. These devices are not constrained anymore by the table in AN205,
and are able to generate almost any baudrate in the supported range
with only minimal errors. This has also been verified with a scope on
a physical device. This patch adds support for all baudrates supported
by the CP2102N.
Signed-off-by: Karoly Pados <pados@pados.hu>
[johan: rework on top of an205 and max-speed patches ]
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Newer cp210x devices support higher line speeds than the older ones
which supported a discrete set of speeds up to 921.6 kbaud.
To support these higher speeds, we have for some time mapped speeds
lower than 1 Mbaud to the speeds supported by older devices, while
allowing the device to pick the closest possible rate for higher speeds
(without trying to guess and report back what rate was actually chosen).
As this implementation can lead to undefined behaviour for older devices
which do not support the higher rates, let's use the later-added
device-type detection to determine the maximum supported speed.
This will also be useful when adding support for cp2102n which can
handle rates up to 3 Mbaud.
As per the data sheets the following maximum speeds are used
cp2101 921.6 kbaud
cp2102/3 1 Mbaud
cp2104/8 2 Mbaud
cp2105
- ECI port 2 Mbaud
- SCI port 921.6 kbaud
while keeping the maximum 2 Mbaud for unknown device types in order to
avoid any regressions.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Older cp210x devices only support a fixed set of line speeds to which a
requested speed is mapped. Reimplement this mapping using a table
instead of a long if-else construct.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The list [1] of commits doing endianness fixes in USB subsystem is long
due to below quote from USB spec Revision 2.0 from April 27, 2000:
------------
8.1 Byte/Bit Ordering
Multiple byte fields in standard descriptors, requests, and responses
are interpreted as and moved over the bus in little-endian order, i.e.
LSB to MSB.
------------
This commit belongs to the same family.
[1] Example of endianness fixes in USB subsystem:
commit 14e1d56cbe ("usb: gadget: f_uac2: endianness fixes.")
commit 42370b8211 ("usb: gadget: f_uac1: endianness fixes.")
commit 63afd5cc78 ("USB: chaoskey: fix Alea quirk on big-endian hosts")
commit 74098c4ac7 ("usb: gadget: acm: fix endianness in notifications")
commit cdd7928df0 ("ACM gadget: fix endianness in notifications")
commit 323ece54e0 ("cdc-wdm: fix endianness bug in debug statements")
commit e102609f10 ("usb: gadget: uvc: Fix endianness mismatches")
list goes on
Fixes: 132fcb4608 ("usb: gadget: Add Audio Class 2.0 Driver")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Make sure only to copy any actual data rather than the whole buffer,
when releasing the temporary buffer used for unaligned non-isochronous
transfers.
Taken directly from commit 0efd937e27 ("USB: ehci-tegra: fix inefficient
copy of unaligned buffers")
Tested with Lantiq xRX200 (MIPS) and RPi Model B Rev 2 (ARM)
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The commit 3bc04e28a0 ("usb: dwc2: host: Get aligned DMA in a more
supported way") introduced a common way to align DMA allocations.
The code in the commit aligns the struct dma_aligned_buffer but the
actual DMA address pointed by data[0] gets aligned to an offset from
the allocated boundary by the kmalloc_ptr and the old_xfer_buffer
pointers.
This is against the recommendation in Documentation/DMA-API.txt which
states:
Therefore, it is recommended that driver writers who don't take
special care to determine the cache line size at run time only map
virtual regions that begin and end on page boundaries (which are
guaranteed also to be cache line boundaries).
The effect of this is that architectures with non-coherent DMA caches
may run into memory corruption or kernel crashes with Unhandled
kernel unaligned accesses exceptions.
Fix the alignment by positioning the DMA area in front of the allocation
and use memory at the end of the area for storing the orginal
transfer_buffer pointer. This may have the added benefit of increased
performance as the DMA area is now fully aligned on all architectures.
Tested with Lantiq xRX200 (MIPS) and RPi Model B Rev 2 (ARM).
Fixes: 3bc04e28a0 ("usb: dwc2: host: Get aligned DMA in a more supported way")
Cc: <stable@vger.kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The Aspeed SoC has a memory ordering issue that (thankfully)
only affects the USB gadget device. A read back is necessary
after writing to memory and before letting the device DMA
from it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Variable maxpacket is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'maxpacket' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For unidirectional endpoints, the endpoint pointer will be NULL for the
unused direction. Check that the endpoint is active before
dereferencing this pointer.
Fixes: 1b4977c793 ("usb: dwc2: Update dwc2_handle_incomplete_isoc_in() function")
Fixes: 689efb2619 ("usb: dwc2: Update dwc2_handle_incomplete_isoc_out() function")
Fixes: d84845522d ("usb: dwc2: Update GINTSTS_GOUTNAKEFF interrupt handling")
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix build errors when built for PPC64:
These variables are only used on PPC32 so they don't need to be
initialized for PPC64.
../drivers/usb/phy/phy-fsl-usb.c: In function 'usb_otg_start':
../drivers/usb/phy/phy-fsl-usb.c:865:3: error: '_fsl_readl' undeclared (first use in this function); did you mean 'fsl_readl'?
_fsl_readl = _fsl_readl_be;
../drivers/usb/phy/phy-fsl-usb.c:865:16: error: '_fsl_readl_be' undeclared (first use in this function); did you mean 'fsl_readl'?
_fsl_readl = _fsl_readl_be;
../drivers/usb/phy/phy-fsl-usb.c:866:3: error: '_fsl_writel' undeclared (first use in this function); did you mean 'fsl_writel'?
_fsl_writel = _fsl_writel_be;
../drivers/usb/phy/phy-fsl-usb.c:866:17: error: '_fsl_writel_be' undeclared (first use in this function); did you mean 'fsl_writel'?
_fsl_writel = _fsl_writel_be;
../drivers/usb/phy/phy-fsl-usb.c:868:16: error: '_fsl_readl_le' undeclared (first use in this function); did you mean 'fsl_readl'?
_fsl_readl = _fsl_readl_le;
../drivers/usb/phy/phy-fsl-usb.c:869:17: error: '_fsl_writel_le' undeclared (first use in this function); did you mean 'fsl_writel'?
_fsl_writel = _fsl_writel_le;
and the sysfs "show" function return type should be ssize_t, not int:
../drivers/usb/phy/phy-fsl-usb.c:1042:49: error: initialization of 'ssize_t (*)(struct device *, struct device_attribute *, char *)' {aka 'long int (*)(struct device *, struct device_attribute *, char *)'} from incompatible pointer type 'int (*)(struct device *, struct device_attribute *, char *)' [-Werror=incompatible-pointer-types]
static DEVICE_ATTR(fsl_usb2_otg_state, S_IRUGO, show_fsl_usb2_otg_state, NULL);
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: linux-usb@vger.kernel.org
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When handling split transactions we will try to delay retry after
getting a NAK from the device. This works well for BULK transfers that
can be polled for essentially forever. Unfortunately, on slower systems
at boot time, when the kernel is busy enumerating all the devices (USB
or not), we issue a bunch of control requests (reading device
descriptors, etc). If we get a NAK for the IN part of the control
request and delay retry for too long (because the system is busy), we
may confuse the device when we finally get to reissue SSPLIT/CSPLIT IN
and the device will respond with STALL. As a result we end up with
failure to get device descriptor and will fail to enumerate the device:
[ 3.428801] usb 2-1.2.1: new full-speed USB device number 9 using dwc2
[ 3.508576] usb 2-1.2.1: device descriptor read/8, error -32
[ 3.699150] usb 2-1.2.1: device descriptor read/8, error -32
[ 3.891653] usb 2-1.2.1: new full-speed USB device number 10 using dwc2
[ 3.968859] usb 2-1.2.1: device descriptor read/8, error -32
...
Let's not delay retries of split CONTROL IN transfers, as this allows us
to reliably enumerate devices at boot time.
Fixes: 38d2b5fb75 ("usb: dwc2: host: Don't retry NAKed transactions right away")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Substream period size potentially can be changed in runtime, however
this is not accounted in the data copying routine, the change replaces
the cached value with an actual value from substream runtime.
As a side effect the change also removes a potential division by zero
in u_audio_iso_complete() function, if there is a race with
uac_pcm_hw_free(), which sets prm->period_size to 0.
Fixes: 132fcb4608 ("usb: gadget: Add Audio Class 2.0 Driver")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is no necessity to copy PCM stream ring buffer area and size
properties to UAC private data structure, these values can be got
from substream itself.
The change gives more control on substream and avoid stale caching.
Fixes: 132fcb4608 ("usb: gadget: Add Audio Class 2.0 Driver")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In u_audio_iso_complete, the runtime hw_ptr is updated before the
data is actually copied over to/from the buffer/dma area. When
ALSA uses this hw_ptr, the data may not actually be available to
be used. This causes trash/stale audio to play/record. This
patch updates the hw_ptr after the data has been copied to avoid
this.
Fixes: 132fcb4608 ("usb: gadget: Add Audio Class 2.0 Driver")
Signed-off-by: Joshua Frkuska <joshua_frkuska@mentor.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix below smatch (v0.5.0-4443-g69e9094e11c1) warnings:
drivers/usb/gadget/function/u_audio.c:607 g_audio_setup() warn: strcpy() 'pcm_name' of unknown size might be too large for 'pcm->name'
drivers/usb/gadget/function/u_audio.c:614 g_audio_setup() warn: strcpy() 'card_name' of unknown size might be too large for 'card->driver'
drivers/usb/gadget/function/u_audio.c:615 g_audio_setup() warn: strcpy() 'card_name' of unknown size might be too large for 'card->shortname'
Below commits performed a similar 's/strcpy/strlcpy/' rework:
* v2.6.31 commit 8372d4980f ("ALSA: ctxfi - Fix PCM device naming")
* v4.14 commit 003d3e70db ("ALSA: ad1848: fix format string overflow warning")
* v4.14 commit 6d8b04de87 ("ALSA: cs423x: fix format string overflow warning")
Fixes: eb9fecb9e6 ("usb: gadget: f_uac2: split out audio core")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The driver may sleep in an interrupt handler.
The function call path (from bottom to top) in Linux-4.16.7 is:
[FUNC] r8a66597_queue(GFP_KERNEL)
drivers/usb/gadget/udc/r8a66597-udc.c, 1193:
r8a66597_queue in get_status
drivers/usb/gadget/udc/r8a66597-udc.c, 1301:
get_status in setup_packet
drivers/usb/gadget/udc/r8a66597-udc.c, 1381:
setup_packet in irq_control_stage
drivers/usb/gadget/udc/r8a66597-udc.c, 1508:
irq_control_stage in r8a66597_irq (interrupt handler)
To fix this bug, GFP_KERNEL is replaced with GFP_ATOMIC.
This bug is found by my static analysis tool (DSAC-2) and checked by
my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The driver may sleep with holding a spinlock.
The function call paths (from bottom to top) in Linux-4.16.7 are:
[FUNC] msleep
drivers/usb/gadget/udc/r8a66597-udc.c, 839:
msleep in init_controller
drivers/usb/gadget/udc/r8a66597-udc.c, 96:
init_controller in r8a66597_usb_disconnect
drivers/usb/gadget/udc/r8a66597-udc.c, 93:
spin_lock in r8a66597_usb_disconnect
[FUNC] msleep
drivers/usb/gadget/udc/r8a66597-udc.c, 835:
msleep in init_controller
drivers/usb/gadget/udc/r8a66597-udc.c, 96:
init_controller in r8a66597_usb_disconnect
drivers/usb/gadget/udc/r8a66597-udc.c, 93:
spin_lock in r8a66597_usb_disconnect
To fix these bugs, msleep() is replaced with mdelay().
This bug is found by my static analysis tool (DSAC-2) and checked by
my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The current code is broken as it re-defines "req" inside the
if block, then goto out of it. Thus the request that ends
up being sent is not the one that was populated by the
code in question.
This fixes RNDIS driver autodetect by Windows 10 for me.
The bug was introduced by Chris rework to remove the local
queuing inside the if { } block of the redefined request.
Fixes: 636ba13aec ("usb: gadget: composite: remove duplicated code in OS desc handling")
Cc: <stable@vger.kernel.org> # v4.17
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
A couple of bugs in the driver are preventing SETUP packets
with an OUT data phase from working properly.
Interestingly those are incredibly rare (RNDIS typically
uses them and thus is broken without this fix).
The main problem was an incorrect register offset being
applied for arming RX on EP0. The other problem relates
to stalling such a packet before the data phase, in which
case we don't get an ACK cycle, and get the next SETUP
packet directly, so we shouldn't reject it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Drop redundant input-speed re-encoding at every open(). The output and
input speeds are initialised to the same value and are kept in sync on
termios updates.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Variables iflag, mask and serial are being assigned but are never used
hence are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'iflag' set but not used [-Wunused-but-set-variable]
warning: variable 'mask' set but not used [-Wunused-but-set-variable]
warning: variable 'serial' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The device (a POS terminal) implements CDC ACM, but has not union
descriptor.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQEwBAABCAAaBQJbRA8GExxwZXRlci5jaGVuQG54cC5jb20ACgkQSFkpgVDWcbsE
Ygf/QAv1RHor7dx2XO0p2lfVSscQegsoXFobtRhItfmwbS1i/P5iavfMqIxRosBh
xac2hHwGSn3isAMRfak3oyKbyrVKo0MYnHHKiQAc1U6X//DQCYfZ933H5wEzXj8q
KvPPPmMLrD5EAgkNcNruYMx0/Onwch/azR+njozVGFpZWfRkAURePGeb0dCTZl/f
/+1Sa3J28No62cUpKrqs55/POjaHSibY8D9iwlQxImkeaBtJNTohevkEUfJunbJ3
0VVWgfEh4BpuInVv6Wu7UzjggRPUrfhozny6qxfHfNpc/RLkZtzcDLD5IsOy3vHc
8cRtU/AamMX3J/tOiAC1tSOSaQ==
=hohq
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
One regression fix causes imx51 board hang when using ULPI PHY
Variable maxpacket is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'maxpacket' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer dev is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'dev' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable num_ports is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'num_ports' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable t is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 't' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer dbc is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
variable 'dbc' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable 'selector' is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'selector' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable modey is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'modey' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer usbdev is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'usbdev' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer ep is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'ep' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver was apparently never tested with an actual KLSI device. In
fact, even the device-id entry which was supposed to allow for this had
a typo in it.
Tests now reveal that the predicted firmware differences with the
PalmConnect adapters are real and that the driver does not support KLSI
devices with PID 0x000c, so let's remove the broken entry.
Reported-by: Chris Jakob <chris.jakob@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In general, accessing userspace memory beyond the length of the supplied
buffer in VFS read/write handlers can lead to both kernel memory corruption
(via kernel_read()/kernel_write(), which can e.g. be triggered via
sys_splice()) and privilege escalation inside userspace.
Fix it by using simple_read_from_buffer() instead of custom logic.
Fixes: 6bc235a2e2 ("USB: add driver for Meywa-Denki & Kayac YUREX")
Signed-off-by: Jann Horn <jannh@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a condition check about the PLL acvice of this
controller. Otherwise, the controller might cause hang when
any USB clocks are not supplied yet and accesses the xHCI registers.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch simplifies getting the firmware name for R-Car Gen3.
Almost all R-Car Gen3 USB3.0 Host controllers use "V3". But,
r8a7795 ES1.x SoCs only should use "V2". Since the xhci-plat already
has the firmware_name of R-Car Gen3 as "V3", the xhci-rcar doesn't
need some members of rcar_quirks_match.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To clean up the xhci-rcar.c code later, this patch adds firmware_name
"V3" for R-Car Gen3.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc-8 points out that the fix-byte buffer might be too small if
desc->mode is a three-digit number:
drivers/usb/typec/class.c: In function 'typec_register_altmode':
drivers/usb/typec/class.c:502:32: error: '%d' directive writing between 1 and 3 bytes into a region of size 2 [-Werror=format-overflow=]
sprintf(alt->group_name, "mode%d", desc->mode);
^~
drivers/usb/typec/class.c:502:27: note: directive argument in the range [0, 255]
sprintf(alt->group_name, "mode%d", desc->mode);
^~~~~~~~
drivers/usb/typec/class.c:502:2: note: 'sprintf' output between 6 and 8 bytes into a destination of size 6
sprintf(alt->group_name, "mode%d", desc->mode);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
I assume this cannot happen in practice, but we can simply make the
string long enough to avoid the warning. This uses the two padding
bytes that already exist after the string.
Fixes: 4ab8c18d4d ("usb: typec: Register a device for every mode")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of the error handling paths forgets to unlock dp->lock on the error
exit path leading to a potential lock-up. Also the return path for a
successful call to the function configuration_store can return an
uninitialized error return code if dp->alt->active is false, so ensure
ret is zeroed on the successful exit path to avoid garbage being returned.
Detected by CoverityScan, CID#1471597 ("Unitialized scalar variable")
Fixes: 0e3bb7d689 ("usb: typec: Add driver for DisplayPort alternate mode")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer adev is being dereferenced before it is being sanity
checked with a null pointer check, hence it is possible for
a null pointer dereference to occur. Fix this by dereferencing
adev only once it is null checked.
Detected by CoverityScan, CID#1471598 ("Dereference before null check")
Fixes: 8a37d87d72 ("usb: typec: Bus type for alternate modes")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Corsair Strafe appears to suffer from the same issues
as the Corsair Strafe RGB.
Apply the same quirks (control message delay and init delay)
that the RGB version has to 1b1c:1b15.
With these quirks in place the keyboard works correctly upon
booting the system, and no longer requires reattaching the device.
Signed-off-by: Nico Sneck <snecknico@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The > should be >= here so that we don't read one element beyond the end
of the ep->stream_info->stream_rings[] array.
Fixes: e9df17eb14 ("USB: xhci: Correct assumptions about number of rings per endpoint.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without that option, we run into a link failure:
drivers/usb/gadget/udc/aspeed-vhub/hub.o: In function `ast_vhub_std_hub_request':
hub.c:(.text+0x5b0): undefined reference to `usb_gadget_get_string'
Fixes: 7ecca2a408 ("usb/gadget: Add driver for Aspeed SoC virtual hub")
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are three fixes for broken control-transfer error handling, which
could lead to uninitialised slab data leaking to user space.
Included is also a new device id for cp210x.
All but the final two patches have been in linux-next with no reported
issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=UDQ5
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.18-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
USB-serial fixes for v4.18-rc4
Here are three fixes for broken control-transfer error handling, which
could lead to uninitialised slab data leaking to user space.
Included is also a new device id for cp210x.
All but the final two patches have been in linux-next with no reported
issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
Add missing version-request error handling and suppress printing of the
(zeroed) transfer-buffer content in case of errors.
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to return -EIO in case of a short modem-status read request.
While at it, split the debug message to not include the (zeroed)
transfer-buffer content in case of errors.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Add missing transfer-length sanity check to the status-register
completion handler to avoid leaking bits of uninitialised slab data to
user space.
Fixes: 3f5429746d ("USB: Moschip 7840 USB-Serial Driver")
Cc: stable <stable@vger.kernel.org> # 2.6.19
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix broken modem-status error handling which could lead to bits of slab
data leaking to user space.
Fixes: 3b36a8fd67 ("usb: fix uninitialized variable warning in keyspan_pda")
Cc: stable <stable@vger.kernel.org> # 2.6.27
Signed-off-by: Johan Hovold <johan@kernel.org>
The led trigger core learned a few things that allow to simplify the
trigger drivers. Make use of automated trigger attributes and error
checking of the activate callback. Also use the wrappers to set and get
trigger_data.
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Given that activating a trigger can fail, let the callback return an
indication. This prevents to have a trigger active according to the
"trigger" sysfs attribute but not functional.
All users are changed accordingly to return 0 for now. There is no intended
change in behaviour.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Commit 03e6275ae3 ("usb: chipidea: Fix ULPI on imx51") causes a kernel
hang on imx51 systems that use the ULPI interface and do not select the
CONFIG_USB_CHIPIDEA_ULPI option.
In order to avoid such potential misuse, let's always build the
chipidea ULPI code into the final ci_hdrc object.
Tested on a imx51-babbage board.
Fixes: 03e6275ae3 ("usb: chipidea: Fix ULPI on imx51")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
There are two versions of the Qivicon Zigbee stick in circulation. This
adds the second USB ID to the cp210x driver.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The "r" variable is an int and "bufsize" is an unsigned int so the
comparison is type promoted to unsigned. If usb_control_msg() returns a
negative that is treated as a high positive value and the error handling
doesn't work.
Fixes: 2d5a9c72d0 ("USB: serial: ch341: fix control-message error handling")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Since most target drivers do not use the second fabric_make_tpg() argument
("group") and since it is trivial to derive the group pointer from the wwn
pointer, do not pass the group pointer to fabric_make_tpg().
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The set_current_limit tcpm_dev callback is optional and the tcpm core
will already log the passed in values, so there is no need to have an
empty implementation of this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Comparing an int to a size, which is unsigned, causes the int to become
unsigned, giving the wrong result. usb_get_descriptor can return a
negative error code.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
int x;
expression e,e1;
identifier f;
@@
*x = f(...);
... when != x = e1
when != if (x < 0 || ...) { ... return ...; }
*x < sizeof(e)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds more complete handling of VDMs and registration of
partner alternate modes, and introduces callbacks for
alternate mode operations.
Only DFP role is supported for now.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of the tcpm specific mux states, using the generic
USB Type-C connector state values, and with DisplayPort
using connector states defined for the DisplayPort Alt Mode.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DisplayPort USB Type-C Alt Mode allows DisplayPort displays
and adapters to be attached to the USB Type-C ports on the
system.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introducing a simple bus for the alternate modes. Bus allows
binding drivers to the discovered alternate modes the
partners support.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before a device was created for every discovered SVID, but
this will create a device for every discovered mode of every
SVID. The idea is to make it easier to create mode specific
drivers once a bus for the alternate mode is added.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order for the muxes to be usable with alternate modes,
the alternate mode devices will need also to be able to get
a handle to the muxes on top of the port devices. To make
that possible, the muxes need to be possible to request with
an identifier.
This will change the API so that the mux identifier is given
as a function parameter to typec_mux_get(), and the hard-coded
"typec-mux" is replaced with that value.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f2a8aa053c ("typec: tcpm: Represent source supply through
power_supply") moved the code to register a power_supply representing
the device supplying power to the type-C connector, from the fusb302
code to the generic tcpm code so that we have a psy reporting the
supply voltage and current for all tcpm devices.
This broke the reporting of current and voltage through the psy interface
when supplied by a a non pd supply (5V, current as reported by
get_current_limit). The cause of this breakage is port->supply_voltage
and port->current_limit not being set in that case.
This commit fixes this by setting port->supply_voltage and
port->current_limit from tcpm_set_current_limit().
This commit also removes setting supply_voltage and current_limit
from tcpm_reset_port() as that calls tcpm_set_current_limit(0, 0)
which now already sets these to 0.
Fixes: f2a8aa053c ("typec: tcpm: Represent source supply through...")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pm_runtime_put_sync() gets called everytime in xhci_dbc_stop().
If dbc is not started, this makes the runtime PM counter incorrectly
becomes 0, and calls autosuspend function. Then we'll keep seeing this:
[54664.762220] xhci_hcd 0000:00:14.0: Root hub is not suspended
So only calls pm_runtime_put_sync() when dbc was started.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds function typec_get_orientation() that can be used
for checking the current cable plug orientation.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move TCPCI(Typec port controller interface) driver and rt1711h
driver out of staging.
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As DRP port autonomously toggles the Rp/Rd need a start value to
begin with, so add one parameter for it in tcpm_start_drp_toggling.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support of get typec and power delivery config from
firmware description.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Li Jun <jun.li@nxp.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds 3 APIs to get the typec port power and data type,
and preferred power role by its name string.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add fwnode handle to get the fwnode so we can get typec configs
it contains.
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the quest to remove all stack VLA usage from the kernel[1], this
uses the maximum buffer size and adds a sanity check. While 25 bytes
is the size of the largest current things coming through, Heikki
Krogerus pointed out that the actual max in 64 bytes, as per ch 1.3.2
http://www.ti.com/lit/ug/slvuan1a/slvuan1a.pdf
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Cc: Oliver Neukum <oneukum@suse.com>
Cc: "Bjørn Mork" <bjorn@mork.no>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the code path
__usb_hcd_giveback_urb()
-> wdm_in_callback()
-> service_outstanding_interrupt()
The function service_outstanding_interrupt() will unconditionally enable
interrupts during unlock and invoke usb_submit_urb() with GFP_KERNEL.
If the HCD completes in BH (like ehci does) then the context remains
atomic due local_bh_disable() and enabling interrupts does not change
this.
Defer the error case handling to a workqueue as suggested by Oliver
Neukum. In case of an error the worker performs the read out and wakes
the user.
Fixes: c1da59dad0 ("cdc-wdm: Clear read pipeline in case of error")
Cc: Robert Foss <robert.foss@collabora.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bin Liu