Some drivers require knowledge of what connection handle is assigned
to what connection link type (ACL or SCO/eSCO). Instead of having each
driver implement connection tracking, provide a simple helper function
for lookup of the link type.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some vendors decide to use a strict duplicate filter policy that only
filters on Bluetooth device addresses. This means that when the RSSI
changes, these devices are not reported again. During discovery it is
useful to actually get the RSSI updates.
Since this is specific to each controller, add a new quirk setting
that allows drivers to tell the core what kind of filtering policy
the controller uses.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some Bluetooth drivers require to reset the upper stack. To avoid having
all drivers send HCI Hardware Error events, provide a generic function
to wrap the reset functionality.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the HCI_Hardware_Error event is send by the controller or
injected by the driver, then at least print an error message.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Systematically removing the LE connection parameters and autoconnect
action is inconvenient for rebonding without disconnecting from
userland (i.e. unpairing followed by repairing without
disconnecting). The parameters will be lost after unparing and
userland needs to take care of book-keeping them and re-adding them.
This patch allows userland to forget about parameter management when
rebonding without disconnecting. It defers clearing the connection
parameters when unparing without disconnecting, giving a chance of
keeping the parameters if a repairing happens before the connection is
closed.
Signed-off-by: Alfonso Acosta <fons@spotify.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There are scenarios when autoconnecting to a device after the
reception of an ADV_IND report (action 0x02), in which userland
might want to examine the report's contents.
For instance, the Service Data might have changed and it would be
useful to know ahead of time before starting any GATT procedures.
Also, the ADV_IND may contain Manufacturer Specific data which would
be lost if not propagated to userland. In fact, this patch results
from the need to rebond with a device lacking persistent storage which
notifies about losing its LTK in ADV_IND reports.
This patch appends the ADV_IND report which triggered the
autoconnection to the EIR Data in the Device Connected event.
Signed-off-by: Alfonso Acosta <fons@spotify.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The values of a lot of the mgmt_device_connected() parameters come
straight from a hci_conn object. We can simplify the function by passing
the full hci_conn pointer to it.
Signed-off-by: Alfonso Acosta <fons@spotify.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The core specification defines valid values for the
HCI_Reject_Synchronous_Connection_Request command to be 0x0D-0x0F. So
far the code has been using HCI_ERROR_REMOTE_USER_TERM (0x13) which is
not a valid value and is therefore being rejected by some controllers:
> HCI Event: Connect Request (0x04) plen 10
bdaddr 40:6F:2A:6A:E5:E0 class 0x000000 type eSCO
< HCI Command: Reject Synchronous Connection (0x01|0x002a) plen 7
bdaddr 40:6F:2A:6A:E5:E0 reason 0x13
Reason: Remote User Terminated Connection
> HCI Event: Command Status (0x0f) plen 4
Reject Synchronous Connection (0x01|0x002a) status 0x12 ncmd 1
Error: Invalid HCI Command Parameters
This patch introduces a new define for a value from the valid range
(0x0d == Connection Rejected Due To Limited Resources) and uses it
instead for rejecting incoming connections.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
No caller or macro uses the return value so make all
the functions return void.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The hci_recv_fragment function is no longer used by any driver and thus
do not export it. In fact it is not even needed by the core and it can
be removed altogether.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Bluetooth core already does processing of the HCI command header
and puts it together before sending it to the driver. It is not really
efficient for the driver to look at the HCI command header again in
case it has to make certain decisions about certain commands. To make
this easier, just provide the opcode as part of the SKB control buffer
information. The extra information about the opcode is optional and
only provided for HCI commands.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Whether through HCI with BR/EDR or SMP with LE when authentication fails
we should also notify any pending Pair Device mgmt command. This patch
updates the mgmt_auth_failed function to take the actual hci_conn object
and makes sure that any pending pairing command is notified and cleaned
up appropriately.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Before the move the l2cap_chan the SMP context (smp_chan) didn't have
any kind of proper locking. The best there existed was the
HCI_CONN_LE_SMP_PEND flag which was used to enable mutual exclusion for
potential multiple creators of the SMP context.
Now that SMP has been converted to use the l2cap_chan infrastructure and
since the SMP context is directly mapped to a corresponding l2cap_chan
we get the SMP context locking essentially for free through the
l2cap_chan lock. For all callbacks that l2cap_core.c makes for each
channel implementation (smp.c in the case of SMP) the l2cap_chan lock is
held through l2cap_chan_lock(chan).
Since the calls from l2cap_core.c to smp.c are covered the only missing
piece to have the locking implemented properly is to ensure that the
lock is held for any other call path that may access the SMP context.
This means user responses through mgmt.c, requests to elevate the
security of a connection through hci_conn.c, as well as any deferred
work through workqueues.
This patch adds the necessary locking to all these other code paths that
try to access the SMP context. Since mutual exclusion for the l2cap_chan
access is now covered from all directions the patch also removes
unnecessary HCI_CONN_LE_SMP_PEND flag (once we've acquired the chan lock
we can simply check whether chan->smp is set to know if there's an SMP
context).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The identity address update of all channels for an l2cap_conn needs to
take the lock for each channel, i.e. it's safest to do this by a
separate workqueue callback.
Previously this was partially solved by moving the entire SMP key
distribution behind a workqueue. However, if we want SMP context locking
to be correct and safe we should always use the l2cap_chan lock when
accessing it, meaning even smp_distribute_keys needs to take that lock
which would once again create a dead lock when updating the identity
address.
The simplest way to solve this is to have l2cap_conn manage the deferred
work which is what this patch does. A subsequent patch will remove the
now unnecessary SMP key distribution work struct.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We'll soon use hci_disconnect() from places that are interested to know
whether the hci_send_cmd() really succeeded or not. This patch updates
hci_disconnect() to pass on any error returned from hci_send_cmd().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that there are no more users of the l2cap_conn_shutdown API (since
smp.c switched to using hci_disconnect) we can simply remove it along
with all of it's l2cap_conn variables.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When hci_chan_del is called the disconnection routines get scheduled
through a workqueue. If there's any incoming ACL data before the
routines get executed there's a chance that a new hci_chan is created
and the disconnection never happens. This patch adds a new hci_conn flag
to indicate that we're in the process of driving the connection down. We
set the flag in hci_chan_del and check for it in hci_chan_create so that
no new channels are created for the same connection.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There's no point in passing a "small" timeout to queue_delayed_work() to
try to get the callback faster scheduled. Passing 0 is perfectly valid
and will cause a shortcut to a direct queue_work().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
It's natural to have *_get() functions that increment the reference
count of an object to return the object type itself. This way it's
simple to make a copy of the object pointer and increase the reference
count in a single step. This patch updates two such get() functions,
namely hci_conn_get() and l2cap_conn_get(), and updates the users to
take advantage of the new API.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that SMP has been converted to use fixed channels we've got a bit of
a problem with the hci_conn reference counting. So far the L2CAP code
has kept a reference for each L2CAP channel that was notified of the
connection. With SMP however this would mean that the connection is
never dropped even though there are no other users of it. Furthermore,
SMP already does its own hci_conn reference counting internally,
starting from a security or pairing request and ending with the key
distribution.
This patch makes L2CAP fixed channels default to the L2CAP core not
keeping a hci_conn reference for them. A new FLAG_HOLD_HCI_CONN flag is
added so that L2CAP users can declare an exception to this rule and hold
a reference even for their fixed channels. One such exception is the
L2CAP socket layer which does want a reference for each socket (e.g. an
ATT socket which uses a fixed channel).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Recently the LE passive scanning and auto-connections feature was
introduced. It uses the hci_connect_le() API which returns a hci_conn
along with a reference count to that object. All previous users would
tie this returned reference to some existing object, such as an L2CAP
channel, and there'd be no leaked references this way. For
auto-connections however the reference was returned but not stored
anywhere, leaving established connections with one higher reference
count than they should have.
Instead of playing special tricks with hci_conn_hold/drop this patch
associates the returned reference from hci_connect_le() with the object
that in practice does own this reference, i.e. the hci_conn_params
struct that caused us to initiate a connection in the first place. Once
the connection is established or fails to establish this reference is
removed appropriately.
One extra thing needed is to call hci_pend_le_actions_clear() before
calling hci_conn_hash_flush() so that the reference is cleared before
the hci_conn objects are fully removed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that there are no-longer any users for l2cap_conn->security_timer we
can go ahead and simply remove it. The patch makes initialization of the
conn->info_timer unconditional since it's better not to leave any
l2cap_conn data structures uninitialized no matter what the underlying
transport.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since we no-longer do special handling of SMP within l2cap_core.c we
don't have any code for calling l2cap_conn_del() when smp.c doesn't like
the data it gets. At the same time we cannot simply export
l2cap_conn_del() since it will try to lock the channels it calls into
whereas we already hold the lock in the smp.c l2cap_chan callbacks (i.e.
it'd lead to a deadlock).
This patch adds a new l2cap_conn_shutdown() API which is very similar to
l2cap_conn_del() except that it defers the call to l2cap_conn_del()
through a workqueue, thereby making it safe to use it from an L2CAP
channel callback.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that we have all the necessary pieces in place we can fully convert
SMP to use the L2CAP channel infrastructure. This patch adds the
necessary callbacks and removes the now unneeded conn->smp_chan pointer.
One notable behavioral change in this patch comes from the following
code snippet:
- case L2CAP_CID_SMP:
- if (smp_sig_channel(conn, skb))
- l2cap_conn_del(conn->hcon, EACCES);
This piece of code was essentially forcing a disconnection if garbage
SMP data was received. The l2cap_conn_del() function is private to
l2cap_conn.c so we don't have access to it anymore when using the L2CAP
channel callbacks. Therefore, the behavior of the new code is simply to
return errors in the recv() callback (which is simply the old
smp_sig_channel()), but no disconnection will occur.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that we have per-adapter SMP data thanks to the root SMP L2CAP
channel we can take advantage of it and attach the AES crypto context
(only used for SMP) to it. This means that the smp_irk_matches() and
smp_generate_rpa() function can be converted to internally handle the
AES context.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch creates the initial SMP L2CAP channels and a skeleton for
their callbacks. There is one per-adapter channel created upon adapter
registration, and then one channel per-connection created through the
new_connection callback. The channels are registered with the reserved
CID 0x1f for now in order to not conflict with existing SMP
functionality. Once everything is in place the value can be changed to
what it should be, i.e. L2CAP_CID_SMP.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In preparation for converting SMP to use l2cap_chan it's useful to add a
few more callback helpers so that smp.c won't need to define all of its
own.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The LE ATT socket uses a special trick where it temporarily sets
BT_CONFIG state for the duration of a security level elevation. In order
to not require special hacks for going back to BT_CONNECTED state in the
l2cap_core.c code the most reasonable place to resume the state is the
resume callback. This patch adds a new flag to track the pending
security level change and ensures that the state is set back to
BT_CONNECTED in the resume callback in case the flag is set.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Similar to our hci_update_background_scan() function we can simplify a
lot of code by creating a unified helper function for doing page scan
updates. This patch adds such a function to hci_core.c and updates all
the relevant places to use it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are several situations where we're interested in knowing whether
we're currently in the process of powering off an adapter. This patch
adds a convenience function for the purpose and makes it public since
we'll soon need to access it from hci_event.c as well.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This setting maps to the HCI_BONDABLE flag which tracks whether we're
bondable or not. Therefore, rename the mgmt setting and respective
command accordingly.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The HCI_PAIRABLE flag isn't actually controlling whether we're pairable
but whether we're bondable. Therefore, rename it accordingly.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Store the default values for minimum and maximum advertising interval
with all the other controller defaults. These vaules are sent to the
adapter whenever advertising is (re)enabled.
Signed-off-by: Georg Lukas <georg@op-co.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When adding remote devices to the kernel using the Add Device management
command, these devices are explicitly allowed to connect. This kind of
incoming connections are possible even when the controller itself is
not connectable.
For BR/EDR this distinction is pretty simple since there is only one
type of incoming connections. With LE this is not that simple anymore
since there are ADV_IND and ADV_DIRECT_IND advertising events.
The ADV_DIRECT_IND advertising events are send for incoming (slave
initiated) connections only. And this is the only thing the kernel
should allow when adding devices using action 0x01. This meaning
of incoming connections is coming from BR/EDR and needs to be
mapped to LE the same way.
Supporting the auto-connection of devices using ADV_IND advertising
events is an important feature as well. However it does not map to
incoming connections. So introduce a new action 0x02 that allows
the kernel to connect to devices using ADV_DIRECT_IND and in addition
ADV_IND advertising reports.
This difference is represented by the new HCI_AUTO_CONN_DIRECT value
for only connecting to ADV_DIRECT_IND. For connection to ADV_IND and
ADV_DIRECT_IND the old value HCI_AUTO_CONN_ALWAYS is used.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If the Bluetooth controller supports Get MWS Transport Layer
Configuration command, then issue it during initialization.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If the Bluetooth controller supports Read Local Supported Codecs
command, then issue it during initialization so that the list of
codecs is known.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Even though our side requests authentication, the original action that
caused it may be remotely triggered, such as an incoming L2CAP or RFCOMM
connect request. To track this information introduce a new hci_conn flag
called HCI_CONN_AUTH_INITIATOR.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We're interested in whether an authentication request is because of a
remote or local action. So far hci_conn_security() has been used both
for incoming and outgoing actions (e.g. RFCOMM or L2CAP connect
requests) so without some modifications it cannot know which peer is
responsible for requesting authentication.
This patch adds a new "bool initiator" parameter to hci_conn_security()
to indicate which side is responsible for the request and updates the
current users to pass this information correspondingly.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Most (probably all) controllers can only deal with a single slave LE
connection at a time. This patch adds a counter for such connections so
that the number can be quickly looked up without iterating the
connections list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We need to be able to track slave vs master LE connections in
hci_conn_hash, and to be able to do that we need to know the role of the
connection by the time hci_conn_add_has() is called. This means in
practice the hci_conn_add() call that creates the hci_conn_object.
This patch adds a new role parameter to hci_conn_add() function to give
the object its initial role value, and updates the callers to pass the
appropriate role to it. Since the function now takes care of
initializing both conn->role and conn->out values we can remove some
other unnecessary assignments.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To make the code more understandable it makes sense to use the new HCI
defines for connection role instead of a "bool master" parameter. This
makes it immediately clear when looking at the function calls what the
last parameter is describing.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Having a dedicated u8 role variable in the hci_conn struct greatly
simplifies tracking of the role, since this is the native way that it's
represented on the HCI level.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
All HCI commands and events, including LE ones, use 0x00 for master role
and 0x01 for slave role. It makes therefore sense to add generic defines
for these instead of the current LE_CONN_ROLE_MASTER. Having clean
defines will also make it possible to provide simpler internal APIs.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The spinlock protecting the L2CAP ident number can be converted into
a mutex since the whole processing is run in a workqueue. So instead
of using a spinlock, just use a mutex here.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The support for LE encryption is optional. When encryption is not
supported then also do not enable the encryption related events.
This moves the event mask setting to the third initialization
stage to ensure that the LE features are available.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There is no external user of the SCO timeout constants and thus
move them into net/bluetooth/sco.c where they are actuallu used.
In addition just remove SCO_CONN_IDLE_TIMEOUT since it is unused.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The SCO_DEFAULT_FLUSH_TO constant has been defined, but it is not
used anywhere and so just remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There exists no external user of struct sco_conn and thus move
it into the one place that is actually using it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There exists no external user of struct sco_pinfo and sco_pi and
thus move it into the one place that is actually using it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The list of L2CAP fixed channels increased with newer versions of the
specification. This just updates the constants for it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The internals of the HCI request framework should not be leaking to
its users. Move them all into net/bluetooth/hci_core.c and provide
a simple hci_req_pending helper function for the one user outside
the framework.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There exists no external user of struct hci_pinfo and hci_pi and thus
move it into the one place that is actually using it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There is only single location using struct hci_sec_filter and with
that there is no point in putting this declaration into a global
header file. So move it right next to its user and make the code
a lot more simpler.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
All the HCI sockets and ioctl based definitions have been in a global
header file that also includes all the HCI protocol structures. To
make this a bit cleaner, move them into its own file.
This also adjusts fs/compat_ioctl.c to only include this new file
and not all the protocol structures that are not needed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Set Connectable/Discoverable mgmt handlers use a hci_request with a
proper callback to handle the HCI command sending. It makes therefore
little sense to have this extra function to be called from hci_event.c
for command failures.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the HCISETSCAN ioctl is the only non-mgmt user we care about for
setting the right discoverable state we can simply do the necessary
updates in the ioctl handler function instead. This then allows the
removal of the mgmt_discoverable function and should simplify that state
handling considerably.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The mgmt_connectable function has been used to ensure that the right
actions to HCI_CONNECTABLE are taken when the HCI_Write_Scan_Enable
command is triggered by something else than mgmt. The only other user
that we really care about is the HCISETSCAN ioctl code, so we can
actually more simply perform the needed changes there instead.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the white list is in use the code would not update the
HCI_CONNECTABLE flag if it gets changed through the ioctl code (e.g.
hciconfig hci0 pscan). Since the flag is important for properly
accepting incoming connections add code to fix it up if necessary and
emit a New Settings mgmt event.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch extends the Add/Remove device commands by letting user space
pass BR/EDR addresses to them. The resulting entries get stored in a new
hdev->whitelist list. The idea is that we can now selectively accept
connections from devices in the list even though HCI_CONNECTABLE is not
set (the actual implementation of this is coming in a subsequent patch).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We already have several lists with struct bdaddr_list entries, and there
will be more in the future. Since the operations for adding, removing,
looking up and clearing entries in these lists are exactly the same it
doesn't make sense to define new functions for every single list. This
patch unifies the functions by passing the list_head to them instead of
a hci_dev pointer.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Authenticated Payload Timeout Expired event is valid for
controllers with BR/EDR Secure Connections support, but also for
LE only controllers supporting LE Ping feature. When either of them
is available enable this event. Previous it was not enabled when
the controller was only supporting LE operation.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Since the real advertising state is now tracked with its own flag we can
simply set/unset the HCI_ADVERTISING flag in the
set_advertising_complete function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Having a single HCI_ADVERTISING flag is problematic since it tries to
track both the real advertising state and the corresponding mgmt
setting. To make the logic simpler and more reliable add a new flag that
only tracks the actual advertising state that has been written to the
controller.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we have both LE scanning and advertising simultaneously enabled we
need a way to tell hci_connect_le() in which role to initiate a
connection. This patch adds a new parameter to the function to give it
the necessary information. For auto-connect and mgmt_pair_device we
always use master role, whereas for L2CAP users (in practice sockets) we
use slave role whenever HCI_ADVERTISING is set and master role
otherwise.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The auth_type value which gets assigned to hci_conn->auth_type is
something that's only used for BR/EDR connections and is of no value for
LE connections. It makes therefore little sense to pass it to the
hci_connect_le() function. This patch removes the parameter from the
function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we establish connections as a consequence of receiving an
advertising report it makes no sense to wait the normal 20 second LE
connection timeout. This patch modifies the hci_connect_le function to
take an extra timeout value and uses a lower 2 second timeout for the
auto-connection case. This timeout is intentionally chosen to be just a
bit higher than the 1.28 second timeout that High Duty Cycle Advertising
uses.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds support for changing the public device address. This feature
is required by controllers that do not provide a public address and
have HCI_QUIRK_INVALID_BDADDR set.
Even if a controller has a public device address, this is useful when
an embedded system wants to use its own value. As long as the driver
provides the set_bdaddr callback, this allows changing the device
address before powering on the controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the external configuration triggers the switch to a configured
controller, it means the setup needs to be run. Controllers that start
out unconfigured have only run limited set of HCI commands. This is
not enough for complete operation and thus run the setup procedure
before announcing the new controller index.
This introduces HCI_CONFIG flag as companion to HCI_SETUP flag. The
HCI_SETUP flag is only used once for the initial setup procedure. And
during that procedure hdev->setup driver callback is called. With the
new HCI_CONFIG the switch from unconfigured to configured state is
triggering the same setup procedure just without hdev->setup. This
is required since bringing a controller back to unconfigured state
from configured state is possible.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When calling Device Remove with BDADDR_ANY we should in a similar way
emit Device Removed events as we do when removing a single device. Since
we have to iterate the list and call device_removed() the dedicated
hci_conn_params_clear_enabled() is not really useful anymore. This patch
removes the helper function and does the event emission and list item
removal in a single loop.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During the setup phase of a controller, the Bluetooth address will be
read and to have that original address available for later use, store
it as setup address.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When one or more of the missing configuration options change, then send
this even to all the other management interface clients.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Set External Configuration management command allows for switching
between configured and unconfigured start if HCI_QURIK_EXTERNAL_CONFIG
is set by the transport driver.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When a controller requires external configuration, then setting this
quirk will allow indicating this.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When a Bluetooth controller does not have a valid public Bluetooth
address, then allow the driver to indicate this. If the quirk is
set, the Bluetooth core will switch to unconfigured state first
and will allow userspace to configure the address before starting
the full initialization of the controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The current existing device quirks are not documented. So instead of
spreading bits and pieces somewhere in the code, add proper comments
on where these quirks can be used and what behavior they change.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The public address configuration option is value 0x02 since the generic
external configuration is value 0x01. So adjust this accordingly and
also add the value 0x01 to the list.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In some circumstances we need to look up entries in pend_le_conns and in
other in pend_le_reports. This patch converts the existing lookup
function for pend_le_conns to something that can be used for both lists.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since there are no more users of this function we can simply go ahead
and remove it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When powering off (hci_dev_do_close) we should clear both the
pend_le_reports and pend_le_conns types of entries. When powering on
respectively we should populate both lists. This patch converts the
hci_pend_le_conns_clear() function into hci_pend_le_actions_clear()
(which can now be static) and converts the restart_le_auto_conns()
function into restart_le_actions().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that there are no-longer any users of the hci_pend_le_conn_del()
function we can simply go ahead and remove it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To simplify manipulation and lookup of hci_conn_params entries of the
type HCI_AUTO_CONN_REPORT it makes sense to store them in their own
list. The new action list_head in hci_conn_params is used for this
purpose.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In preparation to store also HCI_AUTO_CONN_REPORT entries in a list it
makes sense to convert the existing pend_le_conn list head of
hci_conn_params into a more generically named "action". This makes sense
because a parameter entry will never participate in more than one action
list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Read Controller Configuration Information command allows retrieving
details about possible configurations option. The supported options are
returned and also the missing options (if any).
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Since the connection parameters are always a basis for adding entries to
hdev->pend_le_conns (so far of type bdaddr_list) it's simpler and more
efficient to have the parameters themselves be the entries in the
pend_le_conns list. We do this by adding another list_head to the
hci_conn_params struct.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To be able to make the right choice of whether to start passive scanning
or to send out a mgmt_device_found event we need to know if there are
any devices in the le_conn_params list with the auto_connect value set
to HCI_AUTO_CONN_REPORT. This patch adds a counter for this kind of
devices.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This command allows to get the list of currently known controller that
are in unconfigured state.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When a controller in an unconfigured state gets removed, then send
Unconfigured Index Removed events.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When a controller is in unconfigured state it is currently hidden
from the management interface. This change now announces the new
controller with an Unconfigured Index Added event and allows clients
to easily detect the controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With the new unconfigured controller state it is possible to provide a
fully functional HCI transport, but disable the higher level operations
that would normally happen. This way userspace can try to configure the
controller before releases the unconfigured state.
The internal state is represented by HCI_UNCONFIGURED. This replaces the
HCI_QUIRK_RAW_DEVICE quirk as internal state representation. This is now
a real state and drivers can use the quirk to actually trigger this
state. In the future this will allow a more fine grained switching from
unconfigured state to configured state for controller inititialization.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There are more places that can take advantage of is_identity_address()
besides hci_core.c. This patch moves the function to hci_core.h and
gives it the appropriate hci_ prefix.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The calling functions of mgmt_new_conn_param have more information about
the parameters, such as whether the kernel is tracking them or not. It
makes therefore sense to have them pass an initial store_hint value to
the mgmt_new_conn_param function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The caller of hci_le_conn_update is directly interested in knowing what
the best value is for the store_hint parameter of the corresponding
mgmt event. Since hci_le_conn_update knows whether there were stored
parameters that were updated or not we can have it return an initial
store_hint value to the caller.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch implements the new Load Connection Parameters mgmt command
that's intended to load the desired connection parameters for LE
devices.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The 0x00 action value of mgmt means "scan and report" but do not
connect. This is different from HCI_AUTO_CONN_DISABLED so we need a new
value for it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In some circumstances we'll need to either clear only the enabled
parameters or only the disabled ones. This patch adds convenience
functions for this purpose.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We'll soon have specific clear functions for clearing enabled or
disabled entries, so rename the function that removes everything to
clear_all().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some embedded controllers allow the programming of a public address
and this adds vendor support for supporting OEM confguration of such
addresses.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch introduces a new Mgmt event called "New Connection Parameter".
This event indicates to userspace the connection parameters values the
remote device requested.
The user may store these values and load them into kernel. This way, next
time a connection is established to that device, the kernel will use those
parameters values instead of the default ones.
This event is sent when the remote device requests new connection
parameters through connection parameter update procedure. This event is
not sent for slave connections.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Bluetooth 4.1 introduces a new LE meta event called "LE Remote
Connection Parameter Request" event. In order to the controller
sends this event to host, we should enable it during controller
initialization.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for LE Connection Parameters Request Link
Layer control procedure introduced in Core spec 4.1. This procedure
allows a Peripheral or Central to update the Link Layer connection
parameters of an established connection.
Regarding the acceptance of connection parameters, the LL procedure
follows the same approach of L2CAP procedure (see l2cap_conn_param_
update_req function). We accept any connection parameters values as
long as they are within the valid range.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For the Block/Unblock Device mgmt commands we should only emit the
Blocked/Unblocked events on any socket except for the one which received
the command. The code was previously incorrectly trying to look up a
non-existent pending command and thereby ending up not skipping the
command socket for the event.
We can simplify the code a lot by simply sending the event directly from
the command handler functions. We have the reference to the command
socket available there which makes it easy to pass to the mgmt_event
function for skipping.
The only notable side-effect of this is that the old blacklisting
ioctl's no-longer cause mgmt events to be emitted, however as user space
versions using these ioctl's are not mgmt-aware this is acceptable.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are certain subtle differences in behavior when we're encrypted
with the STK, such as allowing re-encryption even though the security
level stays the same. Because of this, add a flag to track whether we're
encrypted with an STK or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Device Found events of the management interface should indicate if
it is possible to connect to a remote device or if it is broadcaster
only advertising. To allow this differentation the Not Connectable flag
is introduced that will be set when it is known that a device can not
be connected.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Providing the flags parameter directly to mgmt_device_found function
makes the core simpler and more readable. With this it becomes a lot
easier to add new flags in the future.
This also changes hci_inquiry_cache_update to just return that flags
needed for mgmt_device_found since that is its only use for the two
return parameters anyway.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The connection interval parameter of hci_conn_params_set are always used
with the controller defaults. So just let hci_conn_params_add set the
controller default and not bother resetting them to controller defaults
every time the hci_conn_params_set is called.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When adding new connection parameters, it is useful to return either
the existing struct or the newly created one.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch renames l2cap_check_conn_param() to hci_check_conn_params()
and moves it to hci_core.h so it can reused in others files. This helper
will be reused in the next patch.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In some cases it is useful to not overwrite connection parametes and
instead just create default ones if they don't exist. This function
does exactly that. hci_conn_params_add will allow to create new
default connection parameters. hci_conn_params_set will set the
values and also create new parameters if they don't exist.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Store the connection latency and supervision timeout default values
with all the other controller defaults. And when needed use them
for new connections.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When devices are added or removed, then make sure that events are send
out to all other clients so that the list of devices can be easily
tracked. This is especially important when external clients are
adding or removing devices within the auto-connection list.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This allows adding or removing devices from the background scanning
list the kernel maintains. Device flagged for auto-connection will
be automatically connected if they are found.
The passive scanning required for auto-connection will be started
and stopped on demand.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the slave updates the connection parameters, store also the
connection latency and supervision timeout information in the
internal list of connection parameters for known devices.
Having these values available allowes the auto-connection
procedure to use the correct values from the beginning without
having to request an update on every connection establishment.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch implements support for the Get Clock Information mgmt
command. This is done by performing one or two HCI_Read_Clock commands
and creating the response from the stored values in the hci_dev and
hci_conn structs.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for storing the local and piconet clock values
from the HCI_Read_Clock command response to the hci_dev and hci_conn
structs. This will be later used in another patch to implement support
for the Get Clock Info mgmt command.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the connection is in master role and it is going to be
disconnected based on the disconnection timeout, then send
the HCI_Read_Clock_Offset command in an attempt to update the
clock offset value in the inquiry cache.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The smp_conn member of struct hci_conn was simply a pointer to the
l2cap_conn object. Since we already have hcon->l2cap_data that points to
the same thing there's no need to have this second variable. This patch
removes it and changes the single place that was using it to use
hcon->l2cap_data instead.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replaces the hard-coded value in hci_bdaddr_is_rpa() helper
by the corresponding macro ADDR_LE_DEV_RANDOM.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the link_mode member of the hci_conn struct is a bit field and we
already have a flags member as well it makes sense to merge these two
together. This patch moves all used link_mode bits into corresponding
flags. To keep backwards compatibility with user space we still need to
provide a get_link_mode() helper function for the ioctl's that expect a
link_mode style value.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To pave the way for actively using debug keys for pairing this patch
adds a new HCI_USE_DEBUG_KEYS flag for the purpose. When the flag is set
we issue a HCI_Write_SSP_Debug mode whenever HCI_Write_SSP_Mode(0x01)
has been issued as well as before issuing a HCI_Write_SSP_Mode(0x00)
command.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There's no point in having boolean variables in the hci_conn struct
since it already has a flags member. This patch converts the flush_key
member into a proper flag.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We're planning to add a flag to actively use debug keys in addition to
simply just accepting them, which makes the current generically named
DEBUG_KEYS flag a bit confusing. Since the flag in practice affects
whether the kernel keeps debug keys around or not rename it to
HCI_KEEP_DEBUG_KEYS.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are two callers of hci_add_link_key(). The first one is the HCI
Link Key Notification event and the second one the mgmt code that
receives a list of link keys from user space. Previously we've had the
hci_add_link_key() function being responsible for also emitting a mgmt
signal but for the latter use case this should not happen. Because of
this a rather awkward new_key paramter has been passed to the function.
This patch moves the mgmt event sending out from the hci_add_link_key()
function, thereby making the code a bit more understandable.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
By returning the added (or updated) key we pave the way for further
refactoring (in subsequent patches) that allows moving the mgmt event
sending out from this function (and thereby removal of the awkward
new_key parameter).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the LE controller changes its connection parameters, it will send
a connection parameter update event. Make sure that the new set of
parameters are stored in hci_conn struct and thus will properly update
the previous values retrieved from the connection complete event.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The LE connection parameters are needed later on to be able to decide
if it is required to trigger connection update procedures. So when the
connection has been established successfully, store the current used
parameters in hci_conn struct.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Create a CoC dynamically instead of one fixed channel for communication
to peer devices.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The highly optimized TX path for L2CAP channels and its fragmentation
within the HCI ACL packets requires to copy data from user provided
IO vectors and also kernel provided memory buffers.
This patch allows channel clients to provide a memcpy_fromiovec callback
to keep this optimized behavior, but adapt it to kernel vs user memory
for the TX path. For all kernel internal L2CAP channels, a default
implementation is provided that can be referenced.
In case of A2MP, this fixes a long-standing issue with wrongly accessing
kernel memory as user memory.
This patch originally by Marcel Holtmann.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
All the special settings configured via debugfs are either developer
only options or temporary solutions. To not clutter the standard flags,
move them to their own dbg_flags entry.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
These defines were probably put in to track authenticated vs
unauthenticated LTKs, however since the LTK struct has a separate
boolean authenticated member these were never used.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The LTK type has really nothing to do with HCI so it makes more sense to
have these in smp.h than hci.h. This patch moves the defines to smp.h
and removes the HCI_ prefix in the same go.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We never store the "master" type of STKs since we request encryption
directly with them so we only need one STK type (the one that's
looked-up on the slave side). Simply remove the unnecessary define and
rename the _SLAVE one to the shorter form.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the whole HCI command, event and data packet processing has been
migrated to use workqueues instead of tasklets, it makes sense to use
struct delayed_work instead of struct timer_list for the timeout
handling. This patch converts the hdev->cmd_timer to use workqueue
as well.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When allocating the L2CAP SKB for transmission, provide the upper layers
with a clear distinction on what is the header and what is the body
portion of the SKB.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The struct l2cap_ctrl fields are wasting an unsigned int when all the
bits can fit into an __u8 field.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The SKB for L2CAP sockets are all allocated in a central callback
in the socket support. Instead of having to pass around the socket
priority all the time, assign it to skb->priority when actually
allocating the SKB.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The struct l2cap_ops field should not allow any modifications and thus
it is better declared as const.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
On the mgmt level we have a key type parameter which currently accepts
two possible values: 0x00 for unauthenticated and 0x01 for
authenticated. However, in the internal struct smp_ltk representation we
have an explicit "authenticated" boolean value.
To make this distinction clear, add defines for the possible mgmt values
and do conversion to and from the internal authenticated value.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support to store local maximum TX power level for
connection when reply for HCI_Read_Transmit_Power_Level is received.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for Get Connection Information mgmt command
which can be used to query for information about connection, i.e. RSSI
and local TX power level.
In general values cached in hci_conn are returned as long as they are
considered valid, i.e. do not exceed age limit set in hdev. This limit
is calculated as random value between min/max values to avoid client
trying to guess when to poll for updated information.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds conn_info_min_age and conn_info_max_age parameters to
debugfs which determine lifetime of connection information. Actual
lifetime will be random value between min and max age.
Default values for min and max age are 1000ms and 3000ms respectively.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support to store local TX power level for connection
when reply for HCI_Read_Transmit_Power_Level is received.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support to store RSSI for connection when reply for
HCI_Read_RSSI is received.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Enabling CONFIG_DEBUG_ATOMIC_SLEEP has shown that some rfcomm functions
acquiring spinlocks call sleeping locks further in the chain. Converting
the offending spinlocks into mutexes makes sleeping safe.
Signed-off-by: Libor Pechacek <lpechacek@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To be consistent, lets use msec for this timeout as well.
Note: This define value is a minimum scan time taken from BT Core spec 4.0,
Vol 3, Part C, chapter 9.2.6
Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With this patch it is possible to control discovery interleaved
timeout value from debugfs.
It is for fine tuning of this timeout.
Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Keep msec instead of jiffies in this define. This is needed by following
patch where we want this timeout to be exposed in debugfs.
Note: Value of this timeout comes from recommendation in BT Core Spec.4.0,
Vol 3, Part C, chapter 13.2.1.
Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Especially in crowded environments it can become frequent that we have
to send out whatever pending event there is stored. Since user space
has its own filtering of small RSSI changes sending a 0 value will
essentially force user space to wake up the higher layers (e.g. over
D-Bus) even though the RSSI didn't actually change more than the
threshold value.
This patch adds storing also of the RSSI for pending advertising reports
so that we report an as accurate RSSI as possible when we have to send
out the stored information to user space.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The line was incorrectly split between the variable type and its name.
This patch fixes the issue.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To avoid too many events being sent to user space and to help parsing of
all available remote device data it makes sense for us to wait for the
scan response and send a single merged Device Found event to user space.
This patch adds a few new variables to hci_dev to track the last
received ADV_IND/ADV_SCAN_IND, i.e. those which will cause a SCAN_REQ to
be send in the case of active scanning. When the SCAN_RSP is received
the pending data is passed together with the SCAN_RSP to the
mgmt_device_found function which takes care of merging them into a
single Device Found event.
We also need a bit of extra logic to handle situations where we don't
receive a SCAN_RSP after caching some data. In such a scenario we simply
have to send out the pending data as it is and then operate on the new
report as if there was no pending data.
We also need to send out any pending data when scanning stops as
well as ensure that the storage is empty at the start of a new active
scanning session. These both cases are covered by the update to the
hci_cc_le_set_scan_enable function in this patch.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we're in peripheral mode (HCI_ADVERTISING flag is set) the most
natural mapping of connect() is to perform directed advertising to the
peer device.
This patch does the necessary changes to enable directed advertising and
keeps the hci_conn state as BT_CONNECT in a similar way as is done for
central or BR/EDR connection initiation.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In preparation for being able to merge ADV_IND/ADV_SCAN_IND and SCAN_RSP
together into a single device found event add a second parameter to the
mgmt_device_found function. For now all callers pass NULL as this
parameters since we don't yet have storing of the last received
advertising report.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The LE scan type paramter defines if active scanning or passive scanning
is in use. Track the currently set value so it can be used for decision
making from other pieces in the core.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The passkey_notify and user_confirm functions in mgmt.c were expecting
different endianess for the passkey, leading to a big endian bug and
sparse warning in recently added SMP code. This patch converts both
functions to expect host endianess and do the conversion to little
endian only when assigning to the mgmt event struct.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In case the pairable option has been disabled, the pairing procedure
does not create keys for bonding. This means that these generated keys
should not be stored persistently.
For LTK and CSRK this is important to tell userspace to not store these
new keys. They will be available for the lifetime of the device, but
after the next power cycle they should not be used anymore.
Inform userspace to actually store the keys persistently only if both
sides request bonding.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The connection signature resolving key (CSRK) is used for attribute
protocol signed write procedures. This change generates a new local
key during pairing and requests the peer key as well.
Newly generated key and received key will be provided to userspace
using the New Signature Resolving Key management event.
The Master CSRK can be used for verification of remote signed write
PDUs and the Slave CSRK can be used for sending signed write PDUs
to the remote device.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The stop_scan_complete function was used as an intermediate step before
doing the actual connection creation. Since we're using hci_request
there's no reason to have this extra function around, i.e. we can simply
put both HCI commands into the same request.
The single task that the intermediate function had, i.e. indicating
discovery as stopped is now taken care of by a new
HCI_LE_SCAN_INTERRUPTED flag which allows us to do the discovery state
update when the stop scan command completes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
LE connection attempts do not have a controller side timeout in the same
way as BR/EDR has (in form of the page timeout). Since we always do
scanning before initiating connections the attempts are always expected
to succeed in some reasonable time.
This patch adds a timer which forces a cancellation of the connection
attempt within 20 seconds if it has not been successful by then. This
way we e.g. ensure that mgmt_pair_device times out eventually and gives
an error response.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds defines for the initiator filter policy parameter values
of the HCI_LE_Create_Connection command. They will be used in a
subsequent patch to check whether we should have a timeout for the
connection attempt or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For SMP we need the local and remote addresses (and their types) that
were used to establish the connection. These may be different from the
Identity Addresses or even the current RPA. To guarantee that we have
this information available and it is correct track these values
separately from the very beginning of the connection.
For outgoing connections we set the values as soon as we get a
successful command status for HCI_LE_Create_Connection (for which the
patch adds a command status handler function) and for incoming
connections as soon as we get a LE Connection Complete HCI event.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The random numbers in Bluetooth Low Energy are 64-bit numbers and should
also be little endian since the HCI specification is little endian.
Change the whole Low Energy pairing to use __le64 instead of a byte
array.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If some of the cleanup commands caused by mgmt_set_powered(off) never
complete we should still force the adapter to be powered down. This is
rather easy to do since hdev->power_off is already a delayed work
struct. This patch schedules this delayed work if at least one HCI
command was sent by the cleanup procedure.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The current LE white list entries require storing in the HCI controller
structure. So provide a storage and access functions for it. In addition
export the current list via debugfs.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add the definitions for clearing the LE white list, adding entries to
the LE white list and removing entries from the LE white list.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hci_blacklist_clear function is not used outside of hci_core.c and
can be made static.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The number of places needing the local Identity Address are starting to
grow so it's better to have a single place for the logic of determining
it. This patch adds a convenience function for getting the Identity
Address and updates the two current places needing this to use it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To know the real source address for incoming connections (needed e.g.
for SMP) we should store the own_address_type parameter that was used
for the last HCI_LE_Write_Advertising_Parameters command. This patch
adds a proper command complete handler for the command and stores the
address type in a new adv_addr_type variable in the hci_dev struct.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patches creates the public hci_req_add_le_passive_scan helper so
it can be re-used outside hci_core.c in the next patch.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We should only accept connection parameters from identity addresses
(public or random static). Thus, we should check the address type
in hci_conn_params_add().
Additionally, since the IRK is removed during unpair, we should also
remove the connection parameters from that device.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduces the LE auto connection options: HCI_AUTO_CONN_
ALWAYS and HCI_AUTO_CONN_LINK_LOSS. Their working mechanism are
described as follows:
The HCI_AUTO_CONN_ALWAYS option configures the kernel to always re-
establish the connection, no matter the reason the connection was
terminated. This feature is required by some LE profiles such as
HID over GATT, Health Thermometer and Blood Pressure. These profiles
require the host autonomously connect to the device as soon as it
enters in connectable mode (start advertising) so the device is able
to delivery notifications or indications.
The BT_AUTO_CONN_LINK_LOSS option configures the kernel to re-
establish the connection in case the connection was terminated due
to a link loss. This feature is required by the majority of LE
profiles such as Proximity, Find Me, Cycling Speed and Cadence and
Time.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduces the LE auto connection infrastructure which
will be used to implement the LE auto connection options.
In summary, the auto connection mechanism works as follows: Once the
first pending LE connection is created, the background scanning is
started. When the target device is found in range, the kernel
autonomously starts the connection attempt. If connection is
established successfully, that pending LE connection is deleted and
the background is stopped.
To achieve that, this patch introduces the hci_update_background_scan()
which controls the background scanning state. This function starts or
stops the background scanning based on the hdev->pend_le_conns list. If
there is no pending LE connection, the background scanning is stopped.
Otherwise, we start the background scanning.
Then, every time a pending LE connection is added we call hci_update_
background_scan() so the background scanning is started (in case it is
not already running). Likewise, every time a pending LE connection is
deleted we call hci_update_background_scan() so the background scanning
is stopped (in case this was the last pending LE connection) or it is
started again (in case we have more pending LE connections). Finally,
we also call hci_update_background_scan() in hci_le_conn_failed() so
the background scan is restarted in case the connection establishment
fails. This way the background scanning keeps running until all pending
LE connection are established.
At this point, resolvable addresses are not support by this
infrastructure. The proper support is added in upcoming patches.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduces the hdev->pend_le_conn list which holds the
device addresses the kernel should autonomously connect. It also
introduces some helper functions to manipulate the list.
The list and helper functions will be used by the next patch which
implements the LE auto connection infrastructure.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
hci_connect() is a very simple and useless wrapper of hci_connect_acl
and hci_connect_le functions. Addtionally, all places where hci_connect
is called the link type value is passed explicitly. This way, we can
safely delete hci_connect, declare hci_connect_acl and hci_connect_le
in hci_core.h and call them directly.
No functionality is changed by this patch.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some LE controllers don't support scanning and creating a connection
at the same time. So we should always stop scanning in order to
establish the connection.
Since we may prematurely stop the discovery procedure in favor of
the connection establishment, we should also cancel hdev->le_scan_
disable delayed work and set the discovery state to DISCOVERY_STOPPED.
This change does a small improvement since it is not mandatory the
user stops scanning before connecting anymore. Moreover, this change
is required by upcoming LE auto connection mechanism in order to work
properly with controllers that don't support background scanning and
connection establishment at the same time.
In future, we might want to do a small optimization by checking if
controller is able to scan and connect at the same time. For now,
we want the simplest approach so we always stop scanning (even if
the controller is able to carry out both operations).
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the "hci_" prefix to le_conn_failed() helper and
declares it in hci_core.h so it can be reused in hci_event.c.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves stop LE scanning duplicate code to one single
place and reuses it. This will avoid more duplicate code in
upcoming patches.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Once mgmt_set_powered(off) starts doing disconnections we'll need to
care about any disconnections in mgmt.c and not just those with the
MGMT_CONNECTED flag set. Therefore, move the check into mgmt.c from
hci_event.c.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We'll soon need to make decisions on toggling the HCI_ADVERTISING flag
based on pending mgmt_set_powered commands. Therefore, move the handling
from hci_event.c into mgmt.c.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a convenience function to return the number of
connections in the conn_hash list. This will be useful once we update
the power off procedure to disconnect any open connections.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The RPA needs to be stored to know which is the current one. Otherwise
it is impossible to ensure that always the correct RPA can be programmed
into the controller when it is needed.
Current code checks if the address in the controller is a RPA, but that
can potentially lead to using a RPA that can not be resolved with the
IRK that has been distributed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When running active scanning during LE discovery, do not reveal the own
identity to the peer devices. In case LE privacy has been enabled, then
a resolvable private address is used. If the LE privacy option is off,
then use an unresolvable private address.
The public address or static random address is never used in active
scanning anymore. This ensures that scan request are send using a
random address.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Now that the identity address type is always looked up for all
successful connections, the hdev->own_addr_type variable has become
completely unnecessary. Simply remove it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a convenience function for updating the local random
address which is needed before advertising, scanning and initiating LE
connections.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a timer for updating the local RPA periodically. The
default timeout is set to 15 minutes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds basic mgmt defines for enabling privacy. This includes a
new setting flag as well as the Set Privacy command.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This code adds a HCI_PRIVACY flag to track whether Privacy support is
enabled (meaning we have a local IRK) and makes sure the IRK is
distributed during SMP key distribution in case this flag is set.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For testing purposes it is useful to provide an option to change the
advertising channel map. So add a debugfs option to allow this.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For Bluetooth controllers with LE support, track the value of the
currently configured random address. It is important to know what
the current random address is to avoid unneeded attempts to set
a new address. This will become important when introducing the
LE privacy support in the future.
In addition expose the current configured random address via
debugfs for debugging purposes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The own_address_type debugfs option does not providing enough
flexibity for interacting with the upcoming LE privacy support.
What really is needed is an option to force using the static address
compared to the public address. The new force_static_address debugfs
option does exactly that. In addition it is also only available when
the controller does actually have a public address. For single mode
LE only controllers this option will not be available.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds the necessary helper function to send the New IRK mgmt
event and makes sure that the function is called at when SMP key
distribution has completed. The event is sent before the New LTK event
so user space knows which remote device to associate with the keys.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves the SMP Long Term Key notification over mgmt from the
hci_add_ltk function to smp.c when both sides have completed their key
distribution. This way we are also able to update the identity address
into the mgmt_new_ltk event.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
It's simpler (one less if-statement) to just evaluate the appropriate
value for store_hint in the mgmt_new_ltk function than to pass a boolean
parameter to the function. Furthermore, this simplifies moving the mgmt
event emission out from hci_add_ltk in subsequent patches.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The SMP code will need to postpone the mgmt event emission for the IRK
and LTKs. To avoid extra lookups at the end of the key distribution
simply return the added value from the add_ltk and add_irk functions.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we initiate pairing through mgmt_pair_device the code has so far
been waiting for a successful HCI Encrypt Change event in order to
respond to the mgmt command. However, putting privacy into the play we
actually want the key distribution to be complete before replying so
that we can include the Identity Address in the mgmt response.
This patch updates the various hci_conn callbacks for LE in mgmt.c to
only respond in the case of failure, and adds a new mgmt_smp_complete
function that the SMP code will call once key distribution has been
completed.
Since the smp_chan_destroy function that's used to indicate completion
and clean up the SMP context can be called from various places,
including outside of smp.c, the easiest way to track failure vs success
is a new flag that we set once key distribution has been successfully
completed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we receive a remote identity address during SMP key distribution we
should ensure that any associated L2CAP channel instances get their
address information correspondingly updated (so that e.g. doing
getpeername on associated sockets returns the correct address).
This patch adds a new L2CAP core function l2cap_conn_update_id_addr()
which is used to iterate through all L2CAP channels associated with a
connection and update their address information.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are many situations where we need to check if an LE address is an
RPA and if so try to look up the IRK for it. To simplify such cases this
patch adds a convenience function for the job.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When mgmt_unpair_device is called we should also remove any associated
IRKs. This patch adds a hci_remove_irk convenience function and ensures
that it's called when mgmt_unpair_device is called.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are many functions that never fail but still declare an integer
return value for no reason. This patch converts these functions to use a
void return value to avoid any confusion of whether they can fail or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When removing Long Term Keys we should also be checking that the given
address type (public vs random) matches. This patch updates the
hci_remove_ltk function to take an extra parameter and uses it for
address type matching.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch implements the Load IRKs command for the management
interface. The command is used to load the kernel with the initial set
of IRKs. It also sets a HCI_RPA_RESOLVING flag to indicate that we can
start requesting devices to distribute their IRK to us.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When implementing support for Resolvable Private Addresses (RPAs) we'll
need to in several places be able to identify such addresses. This patch
adds a simple convenience function to do the identification of the
address type.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the initial IRK storage and management functions to the
HCI core. This includes storing a list of IRKs per HCI device and the
ability to add, remove and lookup entries in that list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Previously the crypto context has only been available for LE SMP
sessions, but now that we'll need to perform operations also during
discovery it makes sense to have this context part of the hci_dev
struct. Later, the context can be removed from the SMP context.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The tty driver api design prefers no-fail writes if the driver
write_room() method has previously indicated space is available
to accept writes. Since this is trivially possible for the
RFCOMM tty driver, do so.
Introduce rfcomm_dlc_send_noerror(), which queues but does not
schedule the krfcomm thread if the dlc is not yet connected
(and thus does not error based on the connection state).
The mtu size test is also unnecessary since the caller already
chunks the written data into mtu size.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Only one session/channel combination may be in use at any one
time. However, the failure does not occur until the tty is
opened (in rfcomm_dlc_open()).
Because these settings are actually bound at rfcomm device
creation (via RFCOMMCREATEDEV ioctl), validate and fail before
creating the rfcomm tty device.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When RFCOMM_RELEASE_ONHUP is set, the rfcomm tty driver 'takes over'
the initial rfcomm_dev reference created by the RFCOMMCREATEDEV ioctl.
The assumption is that the rfcomm tty driver will release the
rfcomm_dev reference when the tty is freed (in rfcomm_tty_cleanup()).
However, if the tty is never opened, the 'take over' never occurs,
so when RFCOMMRELEASEDEV ioctl is called, the reference is not
released.
Track the state of the reference 'take over' so that the release
is guaranteed by either the RFCOMMRELEASEDEV ioctl or the rfcomm tty
driver.
Note that the synchronous hangup in rfcomm_release_dev() ensures
that rfcomm_tty_install() cannot race with the RFCOMMRELEASEDEV ioctl.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
No logic prevents an rfcomm_dev from being released multiple
times. For example, if the rfcomm_dev ref count is large due
to pending tx, then multiple RFCOMMRELEASEDEV ioctls may
mistakenly release the rfcomm_dev too many times. Note that
concurrent ioctls are not required to create this condition.
Introduce RFCOMM_DEV_RELEASED status bit which guarantees the
rfcomm_dev can only be released once.
NB: Since the flags are exported to userspace, introduce the status
field to track state for which userspace should not be aware.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that the LE L2CAP Connection Oriented Channel support has undergone a
decent amount of testing we can make it officially supported. This patch
removes the enable_lecoc module parameter which was previously needed to
enable support for LE L2CAP CoC.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds to hdev the connection parameters list (hdev->le_
conn_params). The elements from this list (struct hci_conn_params)
contains the connection parameters (for now, minimum and maximum
connection interval) that should be used during the connection
establishment.
Moreover, this patch adds helper functions to manipulate hdev->le_
conn_params list. Some of these functions are also declared in
hci_core.h since they will be used outside hci_core.c in upcoming
patches.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The LTK key types available right now are unauthenticated and
authenticated ones. Provide two simple constants for it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The struct smp_ltk does not need to be packed and so remove __packed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The field is not a boolean, it is actually a field for a key type. So
name it properly.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When encryption for LE links has been enabled, it will always be use
AES-CCM encryption. In case of BR/EDR Secure Connections, the link
will also use AES-CCM encryption. In both cases track the AES-CCM
status in the connection flags.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Originally allowing the use of debug keys was done via the Load Link
Keys management command. However this is BR/EDR specific and to be
flexible and allow extending this to LE as well, make this an independent
command.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the controller has been enabled to allow usage of debug keys, then
clearly identify that in the current settings information.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch groups the list_head fields from struct hci_dev together
and removes empty lines between them.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch creates two new fields in struct hci_conn to save the
minimum and maximum connection interval values used to establish
the connection this object represents.
This change is required in order to know what parameters the
connection is currently using.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If LTK distribution happens in both directions we will have two LTKs for
the same remote device: one which is used when we're connecting as
master and another when we're connecting as slave. When looking up LTKs
from the locally stored list we shouldn't blindly return the first match
but also consider which type of key is in question. If we do not do this
we may end up selecting an incorrect encryption key for a connection.
This patch fixes the issue by always specifying to the LTK lookup
functions whether we're looking for a master or a slave key.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There's no reason why A2MP should need or deserve its on channel type.
Instead we should be able to group all fixed CID users under a single
channel type and reuse as much code as possible for them. Where CID
specific exceptions are needed the chan-scid value can be used.
This patch renames the current A2MP channel type to a generic one and
thereby paves the way to allow converting ATT and SMP (and any future
fixed channel protocols) to use the new channel type.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a queue for incoming L2CAP data that's received before
l2cap_connect_cfm is called and processes the data once
l2cap_connect_cfm is called. This way we ensure that we have e.g. all
remote features before processing L2CAP signaling data (which is very
important for making the correct security decisions).
The processing of the pending rx data needs to be done through
queue_work since unlike l2cap_recv_acldata, l2cap_connect_cfm is called
with the hci_dev lock held which could cause potential deadlocks.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For debugging purposes of Secure Connection Only support a simple
debugfs entry is used to indicate if this mode is active or not.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With the introduction of security level 4, the RFCOMM sockets need to
be made aware of this new level. This change ensures that the pairing
requirements are set correctly for these connections.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With the introduction of security level 4, the L2CAP sockets need to
be made aware of this new level. This change ensures that the pairing
requirements are set correctly for these connections.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The security level 4 is a new strong security requirement that is based
around 128-bit equivalent strength for link and encryption keys required
using FIPS approved algorithms. Which means that E0, SAFER+ and P-192
are not allowed. Only connections created with P-256 resulting from
using Secure Connections support are allowed.
This security level needs to be enforced when Secure Connection Only
mode is enabled for a controller or a service requires FIPS compliant
strong security. Currently it is not possible to enable either of
these two cases. This patch just puts in the foundation for being
able to handle security level 4 in the future.
It should be noted that devices or services with security level 4
requirement can only communicate using Bluetooth 4.1 controllers
with support for Secure Connections. There is no backward compatibilty
if used with older hardware.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
It is important to know if Secure Connections support has been enabled
for a given remote device. The information is provided in the remote
host features page. So track this information and provide a simple
helper function to extract the status.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The current management interface only allows to provide the remote
OOB input of P-192 data. This extends the command to also accept
P-256 data as well. To make this backwards compatible, the userspace
can decide to only provide P-192 data or the combined P-192 and P-256
data. It is also allowed to leave the P-192 data empty if userspace
only has the remote P-256 data.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add function to allow adding P-192 and P-256 data to the internal
storage. This also fixes a few coding style issues from the previous
helper functions for the out-of-band credentials storage.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When Secure Connections has been enabled it is possible to provide P-192
and/or P-256 data during the pairing process. The internal out-of-band
credentials storage has been extended to also hold P-256 data.
Initially the P-256 data will be empty and with Secure Connections enabled
no P-256 data will be provided. This is according to the specification
since it might be possible that the remote side did not provide either
of the out-of-band credentials.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Bluetooth 4.1 specification with Secure Connections support has
just been released and controllers with this feature are still in
an early stage.
A handful of controllers have already support for it, but they do
not always identify this feature correctly. This debugfs entry
allows to tell the kernel that the controller can be treated as
it would fully support Secure Connections.
Using debugfs to force Secure Connections support of course does
not make this feature magically appear in all controllers. This
is a debug functionality for early adopters. Once the majority
of controllers matures this quirk will be removed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For Secure Connections support and the usage of out-of-band pairing,
it is needed to read the P-256 hash and randomizer or P-192 hash and
randomizer. This change will read P-192 data when Secure Connections
is disabled and P-192 and P-256 data when it is enabled.
The difference is between using HCI Read Local OOB Data and using the
new HCI Read Local OOB Extended Data command. The first one has been
introduced with Bluetooth 2.1 and returns only the P-192 data.
< HCI Command: Read Local OOB Data (0x03|0x0057) plen 0
> HCI Event: Command Complete (0x0e) plen 36
Read Local OOB Data (0x03|0x0057) ncmd 1
Status: Success (0x00)
Hash C from P-192: 975a59baa1c4eee391477cb410b23e6d
Randomizer R with P-192: 9ee63b7dec411d3b467c5ae446df7f7d
The second command has been introduced with Bluetooth 4.1 and will
return P-192 and P-256 data.
< HCI Command: Read Local OOB Extended Data (0x03|0x007d) plen 0
> HCI Event: Command Complete (0x0e) plen 68
Read Local OOB Extended Data (0x03|0x007d) ncmd 1
Status: Success (0x00)
Hash C from P-192: 6489731804b156fa6355efb8124a1389
Randomizer R with P-192: 4781d5352fb215b2958222b3937b6026
Hash C from P-256: 69ef8a928b9d07fc149e630e74ecb991
Randomizer R with P-256: 4781d5352fb215b2958222b3937b6026
The change for the management interface is transparent and no change
is required for existing userspace. The Secure Connections feature
needs to be manually enabled. When it is disabled, then userspace
only gets the P-192 returned and with Secure Connections enabled,
userspace gets P-192 and P-256 in an extended structure.
It is also acceptable to just ignore the P-256 data since it is not
required to support them. The pairing with out-of-band credentials
will still succeed. However then of course no Secure Connection will
b established.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The support for Secure Connections need to be explicitly enabled by
userspace. This is required since only userspace that can handle the
new link key types should enable support for Secure Connections.
This command handling is similar to how Secure Simple Pairing enabling
is done. It also tracks the case when Secure Connections support is
enabled via raw HCI commands. This makes sure that the host features
page is updated as well.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The MGMT_SETTING_SECURE_CONN setting is used to track the support and
status for Secure Connections from the management interface. For HCI
based tracking HCI_SC_ENABLED flag is used.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With the introduction of Secure Connections, the list of link key types
got extended by P-256 versions of authenticated and unauthenticated
link keys.
To avoid any confusion the previous authenticated and unauthenticated
link key types got ammended with a P912 postfix. And the two new keys
have a P256 postfix now. Existing code using the previous definitions
has been adjusted.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Secure Connections feature introduces the support for P-256 strength
pairings (compared to P-192 with Secure Simple Pairing). This however
means that for out-of-band pairing the hash and randomizer needs to be
differentiated. Two new commands are introduced to handle the possible
combinations of P-192 and P-256. This add the HCI command definition
for both.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Secure Connections feature is optional and host stacks have to
manually enable it. This add the HCI command definiton for reading
and writing this setting.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The support for Secure Connections introduces two new controller
features and one new host feature.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some controller pretend they support the Delete Stored Link Key command,
but in reality they really don't support it.
< HCI Command: Delete Stored Link Key (0x03|0x0012) plen 7
bdaddr 00:00:00:00:00:00 all 1
> HCI Event: Command Complete (0x0e) plen 4
Delete Stored Link Key (0x03|0x0012) ncmd 1
status 0x11 deleted 0
Error: Unsupported Feature or Parameter Value
Not correctly supporting this command causes the controller setup to
fail and will make a device not work. However sending the command for
controller that handle stored link keys is important. This quirk
allows a driver to disable the command if it knows that this command
handling is broken.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This is initial version of
http://tools.ietf.org/html/draft-ietf-6lo-btle-00
By default the 6LoWPAN support is not activated and user
needs to tweak /sys/kernel/debug/bluetooth/hci0/6lowpan
file.
The kernel needs IPv6 support before 6LoWPAN is usable.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add the LMP feature constants for connectionless slave broadcast
and use them for capability testing.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The values in l2cap_chan that are used for actually transmitting data
only need to be initialized right after we've received an L2CAP Connect
Request or just before we send one. The only thing that we need to
initialize though bind() and connect() is the chan->mode value. This way
all other initializations can be done in the l2cap_le_flowctl_init
function (which now becomes private to l2cap_core.c) and the
l2cap_le_flowctl_start function can be completely removed.
Also, since the l2cap_sock_init function initializes the imtu and omtu
to adequate values these do not need to be part of l2cap_le_flowctl_init.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
LE CoC used differend CIC ranges than BR/EDR L2CAP. The start of the
range is the same (0x0040) but the range ends at 0x007f (unlike BR/EDR
where it goes all the way to 0xffff).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Unlike BR/EDR, for LE when we're in the BT_CONNECT state we may or may
not have already have sent the Connect Request. This means that we need
some extra tracking of the request. This patch adds an extra channel
flag to prevent the request from being sent a second time.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Setting the BT_SK_SUSPEND socket flag from the L2CAP core is causing a
dependency on the socket. So instead of doing that, use a channel
callback into the socket handling to suspend.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds new socket options for LE sockets since the existing
L2CAP_OPTIONS socket option is not usable for LE. For now, the new
socket options also require LE CoC support to be explicitly enabled to
leave some playroom in case something needs to be changed in a backwards
incompatible way.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds tracking of L2CAP connection oriented channel local and
remote credits to struct l2cap_chan and ensures that connect requests
and responses contain the right values.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The LE connection oriented channels have their own mode with its own
data transfer rules. In order to implement this properly we need to
distinguish L2CAP channels operating in this mode from other modes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the necessary boiler plate code to handle receiving
L2CAP connect requests over LE and respond to them with a proper connect
response.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the necessary defines and structs for LE connection
oriented channels.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Along with the L2CAP Connection Oriented Channels features it is now
allowed to use both custom fixed CIDs as well as PSM based (connection
oriented connections). Since the support for this (with the subsequent
patches) is still on an experimental stage, add a module parameter to
enable it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
Marcel Holtmann