This fixes a race condition that may occur whenever ST micro busy end
interrupt is raised just after being unmasked but before leaving mmci
interrupt context.
A dead-lock has been found if connecting mmci ST Micro variant whose amba
id is 0x10480180 to some new eMMC that supports internal caches. Whenever
mmci driver enables cache control by programming eMMC's EXT_CSD register,
block driver may request to flush the eMMC internal caches causing mmci
driver to send a MMC_SWITCH command to the card with FLUSH_CACHE operation.
And because busy end interrupt may be mistakenly cleared while not yet
processed, this mmc request may never complete. As a result, mmcqd task
may be stuck forever.
Here is an instance caught by lockup detector which shows that mmcqd task
was hung while waiting for mmc_flush_cache command to complete:
..
[ 240.251595] INFO: task mmcqd/1:52 blocked for more than 120 seconds.
[ 240.257973] Not tainted 4.1.13-00510-g9d91424 #2
[ 240.263109] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 240.270955] mmcqd/1 D c047504c 0 52 2 0x00000000
[ 240.277359] [<c047504c>] (__schedule) from [<c04754a0>] (schedule+0x40/0x98)
[ 240.284418] [<c04754a0>] (schedule) from [<c0477d40>] (schedule_timeout+0x148/0x188)
[ 240.292191] [<c0477d40>] (schedule_timeout) from [<c0476040>] (wait_for_common+0xa4/0x170)
[ 240.300491] [<c0476040>] (wait_for_common) from [<c02efc1c>] (mmc_wait_for_req_done+0x4c/0x13c)
[ 240.309224] [<c02efc1c>] (mmc_wait_for_req_done) from [<c02efd90>] (mmc_wait_for_cmd+0x64/0x84)
[ 240.317953] [<c02efd90>] (mmc_wait_for_cmd) from [<c02f5b14>] (__mmc_switch+0xa4/0x2a8)
[ 240.325964] [<c02f5b14>] (__mmc_switch) from [<c02f5d40>] (mmc_switch+0x28/0x30)
[ 240.333389] [<c02f5d40>] (mmc_switch) from [<c02f0984>] (mmc_flush_cache+0x54/0x80)
[ 240.341073] [<c02f0984>] (mmc_flush_cache) from [<c02ff0c4>] (mmc_blk_issue_rq+0x114/0x4e8)
[ 240.349459] [<c02ff0c4>] (mmc_blk_issue_rq) from [<c03008d4>] (mmc_queue_thread+0xc0/0x180)
[ 240.357844] [<c03008d4>] (mmc_queue_thread) from [<c003cf90>] (kthread+0xdc/0xf4)
[ 240.365339] [<c003cf90>] (kthread) from [<c0010068>] (ret_from_fork+0x14/0x2c)
..
..
[ 240.664311] INFO: task partprobe:564 blocked for more than 120 seconds.
[ 240.670943] Not tainted 4.1.13-00510-g9d91424 #2
[ 240.676078] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 240.683922] partprobe D c047504c 0 564 486 0x00000000
[ 240.690318] [<c047504c>] (__schedule) from [<c04754a0>] (schedule+0x40/0x98)
[ 240.697396] [<c04754a0>] (schedule) from [<c0477d40>] (schedule_timeout+0x148/0x188)
[ 240.705149] [<c0477d40>] (schedule_timeout) from [<c0476040>] (wait_for_common+0xa4/0x170)
[ 240.713446] [<c0476040>] (wait_for_common) from [<c01f3300>] (submit_bio_wait+0x58/0x64)
[ 240.721571] [<c01f3300>] (submit_bio_wait) from [<c01fbbd8>] (blkdev_issue_flush+0x60/0x88)
[ 240.729957] [<c01fbbd8>] (blkdev_issue_flush) from [<c010ff84>] (blkdev_fsync+0x34/0x44)
[ 240.738083] [<c010ff84>] (blkdev_fsync) from [<c0109594>] (do_fsync+0x3c/0x64)
[ 240.745319] [<c0109594>] (do_fsync) from [<c000ffc0>] (ret_fast_syscall+0x0/0x3c)
..
Here is the detailed sequence showing when this issue may happen:
1) At probe time, mmci device is initialized and card busy detection based
on DAT[0] monitoring is enabled.
2) Later during run time, since card reported to support internal caches, a
MMCI_SWITCH command is sent to eMMC device with FLUSH_CACHE operation. On
receiving this command, eMMC may enter busy state (for a relatively short
time in the case of the dead-lock).
3) Then mmci interrupt is raised and mmci_irq() is called:
MMCISTATUS register is read and is equal to 0x01000440. So the following
status bits are set:
- MCI_CMDRESPEND (= 6)
- MCI_DATABLOCKEND (= 10)
- MCI_ST_CARDBUSY (= 24)
Since MMCIMASK0 register is 0x3FF, status variable is set to 0x00000040 and
BIT MCI_CMDRESPEND is cleared by writing MMCICLEAR register.
Then mmci_cmd_irq() is called. Considering the following conditions:
- host->busy_status is 0,
- this is a "busy response",
- reading again MMCISTATUS register gives 0x1000400,
MMCIMASK0 is updated to unmask MCI_ST_BUSYEND bit.
Thus, MMCIMASK0 is set to 0x010003FF and host->busy_status is set to wait
for busy end completion.
Back again in status loop of mmci_irq(), we quickly go through
mmci_data_irq() as there are no data in that case. And we finally go
through following test at the end of while(status) loop:
/*
* Don't poll for busy completion in irq context.
*/
if (host->variant->busy_detect && host->busy_status)
status &= ~host->variant->busy_detect_flag;
Because status variable is not yet null (is equal to 0x40), we do not leave
interrupt context yet but we loop again into while(status) loop. So we run
across following steps:
a) MMCISTATUS register is read again and this time is equal to 0x01000400.
So that following bits are set:
- MCI_DATABLOCKEND (= 10)
- MCI_ST_CARDBUSY (= 24)
Since MMCIMASK0 register is equal to 0x010003FF:
b) status variable is set to 0x01000000.
c) MCI_ST_CARDBUSY bit is cleared by writing MMCICLEAR register.
Then, mmci_cmd_irq() is called one more time. Since host->busy_status is
set and that MCI_ST_CARDBUSY is set in status variable, we just return from
this function.
Back again in mmci_irq(), status variable is set to 0 and we finally leave
the while(status) loop. As a result we leave interrupt context, waiting for
busy end interrupt event.
Now, consider that busy end completion is raised IN BETWEEN steps 3.a) and
3.c). In such a case, we may mistakenly clear busy end interrupt at step
3.c) while it has not yet been processed. This will result in mmc command
to wait forever for a busy end completion that will never happen.
To fix the problem, this patch implements the following changes:
Considering that the mmci seems to be triggering the IRQ on both edges
while monitoring DAT0 for busy completion and that same status bit is used
to monitor start and end of busy detection, special care must be taken to
make sure that both start and end interrupts are always cleared one after
the other.
1) Clearing of card busy bit is moved in mmc_cmd_irq() function where
unmasking of busy end bit is effectively handled.
2) Just before unmasking busy end event, busy start event is cleared by
writing card busy bit in MMCICLEAR register.
3) Finally, once we are no more busy with a command, busy end event is
cleared writing again card busy bit in MMCICLEAR register.
This patch has been tested with the ST Accordo5 machine, not yet supported
upstream but relies on the mmci driver.
Signed-off-by: Sarang Mairal <sarang.mairal@garmin.com>
Signed-off-by: Jean-Nicolas Graux <jean-nicolas.graux@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
One of our kernelCI boxes hanged at boot because a faulty eSDHC device
was triggering spurious CARD_INT interrupts for SD cards, causing CMD52
reads, which are not allowed for SD devices. This adds a sanity check
to the interruption path, preventing that illegal command from getting
sent if the CARD_INT interruption should be disabled.
This quirk allows that particular machine to resume boot despite the
faulty hardware, instead of getting hung dealing with thousands of
mishandled interrupts.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: <stable@vger.kernel.org>
It's necessary to setup bus if any slots are present.
- update clock after ctrl reset
- if the host has genpd node, we can guarantee the clock is
available before starting request. Otherwies, the clock register
is reset once power off the pd, and host can't output the active
clock during communication.
Fixes: e9ed8835e9 ("mmc: dw_mmc: add runtime PM callback")
Fixes: df9bcc2bc0 ("mmc: dw_mmc: add missing codes for runtime resume")
cc: <stable@vger.kernel.org>
Reported-by: Randy Li <randy.li@rock-chips.com>
Reported-by: S. Gilles <sgilles@math.umd.edu>
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the code the intention is to append 8 SCK cycles
instead of 4 at end of a MMC_STOP_TRANSMISSION command. But this
will never happened because it's an AC command not an ADTC command.
So fix this by moving the statement into the right function.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: e4243f13d1 (mmc: mxs-mmc: add mmc host driver for i.MX23/28)
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit e5bbf30733 ("mmc: sdhci-acpi: Ensure connected devices are
powered when probing") introduced code to powerup any acpi child
nodes listed in the dstd. But some dstd-s list all possible devices
used on some board variants, while reporting if the device is actually
present and enabled in the status field of the device.
So we end up calling the acpi _PS0 (power-on) method for devices which
are not actually present. This does not always end well, e.g. on my
cube iwork8 air tablet, this results in freezing the entire tablet as
soon as the r8723bs module is loaded.
This commit fixes this by checking the child device's status.present
and status.enabled bits and only call acpi_device_fix_up_power()
if both are set.
Fixes: e5bbf30733 ("mmc: sdhci-acpi: Ensure connected devices are powered when probing")
BugLink: https://github.com/hadess/rtl8723bs/issues/80
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
No actual segmentation faults were observed but the coding is
at least inconsistent.
irqreturn_t meson_mmc_irq():
We should not dereference host before checking it.
meson_mmc_irq_thread():
If cmd or mrq are NULL we should not dereference them after
writing a warning.
Fixes: 51c5d8447b MMC: meson: initial support for GX platforms
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit c2c24819b2 ("mmc: core: Don't power off the card when
starting the host"), the power state can still be MMC_POWER_UNDEFINED after
mmc_start_host() is called. That can trigger a warning in SDHCI during
runtime resume as it tries to restore the I/O state. Handle
MMC_POWER_UNDEFINED simply by not updating the I/O state in that case.
Fixes: c2c24819b2 ("mmc: core: Don't power off the card when starting the host")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a Socionext SoC specific compatible (suggested by Rob Herring).
No SoC specific data are associated with the compatible strings for
now, but other SoC vendors may use this IP and want to differentiate
IP variants in the future.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a driver for the Cadence SD4HC SD/SDIO/eMMC Controller.
For SD, it basically relies on the SDHCI standard code.
For eMMC, this driver provides some callbacks to support the
hardware part that is specific to this IP design.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some SDHCI-compat controllers support not only SD, but also eMMC,
but they use different commands for tuning: CMD19 for SD, CMD21 for
eMMC.
Due to the difference of the underlying mechanism, some controllers
(at least, the Cadence IP is the case) provide their own registers
for the eMMC tuning.
This commit will be useful when we want to override .execute_tuning
callback (for eMMC HS200 tuning), but still let it fall back to
sdhci_execute_tuning() for SD timing.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tidy the tuning loop by moving it to a separate function and making it a
for-loop.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are only 2 possible block sizes, so simplify 2 if-statements into 1.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out some functions to tidy up the code in sdhci_execute_tuning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use mmc_abort_tuning() instead of open-coding the stop command.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI falls back to fixed sampling if there is an error during tuning.
However it also reports an error unless there is periodic re-tuning.
That is not the best option because:
a) there is a reasonable chance that fixed sampling will work, especially
at room temperature.
b) re-tuning will be done again anyway if there are CRC errors.
Change to return no error always when falling back to fixed sampling.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the driver has exhausted the maximum number of tuning loops, then fixed
sampling is used. To do that both SDHCI_CTRL_TUNED_CLK and
SDHCI_CTRL_EXEC_TUNING must be reset to 0, but only SDHCI_CTRL_TUNED_CLK
was being reset. Reset SDHCI_CTRL_EXEC_TUNING to 0 also.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Clearing the tuning bits should reset the tuning circuit. However there is
more to do. Reset the command and data lines for good measure, and then
for eMMC ensure the card is not still trying to process a tuning command by
sending a stop command.
Note the JEDEC eMMC specification says the stop command (CMD12) can be used
to stop a tuning command (CMD21) whereas the SD specification is silent on
the subject with respect to the SD tuning command (CMD19). Considering that
CMD12 is not a valid SDIO command, the stop command is sent only when the
tuning command is CMD21 i.e. for eMMC. That addresses cases seen so far
which have been on eMMC.
Note that this replaces the commit fe5fb2e3b5 ("mmc: sdhci: Reset cmd and
data circuits after tuning failure") which is being reverted for v4.9+.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Dan O'Donovan <dan@emutex.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit fe5fb2e3b5 ("mmc: sdhci: Reset cmd and data circuits
after tuning failure").
A better fix is available, and it will be applied to older stable releases,
so get this out of the way by reverting it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add an entry for the SDIO bus in the ECS EF20 cherry trail laptop:
Device (SDHB) {
Name (_ADR, 0x00110000)
Name (_HID, "80860F14" /* Intel Baytrail SDIO/MMC Host Controller */)
Name (_CID, "PNP0D40" /* SDA Standard Compliant SD Host Controller */)
Name (_DDN, "Intel(R) SDIO Controller - 80862295")
Name (_UID, 0x02)
Name (_HRV, One)
A SDHB device with the same _HID and _UID can also be found on other
cherry trail products like Chuwi Hi10.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I see no override of read/write callbacks in sdhci-of-at91.c.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On NI 9037 boards the max SDIO frequency is limited by trace lengths
and other layout choices. The max SDIO frequency is stored in an ACPI
table.
The driver reads the ACPI entry MXFQ during sdio_probe_slot and sets the
f_max field of the host.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Reviewed-by: Jaeden Amero <jaeden.amero@ni.com>
Reviewed-by: Josh Cartwright <joshc@ni.com>
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add PCI ID for Intel byt sdio host controller sub-vended by NI.
The controller has different behavior because of the board layout NI
puts it on.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Before calling clk_round_rate(), put the spin_unlock_irq() in
sdhci_s3c_consider_clock() function.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When card is polling (broken-cd), there is a spamming messge related to
clock.
After applied this patch, display the message only one time at boot
time. It's enough to check which clock values is used.
Also prevent to display the spamming message.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If card is polling or non-removable, display the more exact message.
It's helpful to debug which detecting scheme is using.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Before checking flags, it has to check "present" variable.
Otherwise, flags should be cleared everytime.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 64997de4fd17 ("mmc: dw_mmc: remove system PM callback") is
missing to call dw_mci_ctrl_reset(). This adds to call
dw_mci_ctrl_reset() and to handle error of clocks.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The dw_mmc-exynos should be RPM_ACTIVE on probe() to call suspend
callback of runtime PM in pm_runtime_force_suspend() during first system
suspend. Also call pm_runtime_get_noresume() on probe() because it
doesn't call suspend/resume callback by runtime PM now.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The eSDHC of T4240-R1.0-R2.0 has incorrect vender version and spec version.
Acturally the right version numbers should be VVN=0x13 and SVN = 0x1.
This patch adds the GUTS driver support for eSDHC driver to match SoC.
And fix host version to avoid that incorrect version numbers break down
the ADMA data transfer.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Scott Wood <oss@buserror.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The void (*pre_req) callback in the struct mmc_host_ops vtable
is passing an argument "is_first_req" indicating whether this is
the first request or not.
None of the in-kernel users use this parameter: instead, since
they all just do variants of dma_map* they use the DMA cookie
to indicate whether a pre* callback has already been done for
a request when they decide how to handle it.
Delete the parameter from the callback and all users, as it is
just pointless cruft.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With commit f35bbf61ab ("gpio / ACPI: Return -EPROBE_DEFER if the
gpiochip was not found"), a gpio descriptor request can now be deferred if
the providing gpio host controller driver hasn't been loaded yet. Allow use
in mmc slot probe in order to prevent card detect gpio setup from failing
in this case.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The newer msm sdhci's cores use a different DLL hardware for HS400.
Update the configuration and calibration of the newer DLL block.
The HS400 DLL block used previously is CDC LP 533 and requires
programming multiple registers and waiting for configuration to
complete and then enable it. It has about 18 register writes and
two register reads.
The newer HS400 DLL block is SDC4 DLL and requires two register
writes for configuration and one register read to confirm that it
is initialized. There is an additional register write to enable
the power save mode for SDC4 DLL block.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Krishna Konda <kkonda@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In HS400 mode a new RCLK is introduced on the interface for read data
transfers. The eMMC5.0 device transmits the read data to the host with
respect to rising and falling edges of RCLK. In order to ensure correct
operation of read data transfers in HS400 mode, the incoming RX data
needs to be sampled by delayed version of RCLK.
The CDCLP533 delay circuit shifts the RCLK by T/4. It needs to be
initialized, configured and enabled once during HS400 mode switch and
when operational voltage/clock is changed.
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Save the tuning phase once the tuning is performed.
This phase value will be used while calibrating DLL
for HS400 mode.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The following msm platform specific changes are added to support HS400.
- Allow tuning for HS400 mode.
- Configure HS400 timing mode using the VENDOR_SPECIFIC_FUNC register.
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHC MSM controller need 2x clock for MCLK at GCC.
Hence make required changes to have 2x clock for
DDR timing modes.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci-msm controller may have different clk-rates for each
bus speed mode. Thus implement set_clock callback for
sdhci-msm driver.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out sdhci_enable_clk from sdhci_set_clock
and make it EXPORT_SYMBOL so that it can be called.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This add get_min_clock() and get_max_clock() callback
for sdhci-msm. sdhci-msm min/max clocks may be different
hence implement these callbacks.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDCC core with minor version >= 0x42 introduced new 14lpp
DLL. This has additional requirements in the reset sequence
for DLL tuning. Make necessary changes as needed.
Without this patch we see below errors on such SDHC controllers
sdhci_msm 7464900.sdhci: mmc0: DLL failed to LOCK
mmc0: tuning execution failed: -110
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch changes the poor style of writel/readl registers
into more readable format. This avoid mixed style format
of readl/writel in sdhci-msm driver.
This patch also removes the one line comments which were present for
above writel/readl, since they were of no help.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The "clock-freq-min-max" property was deprecated.
There is "max-frequency" property in drivers/mmc/core/host.c
"max-frequency" can be replaced with "clock-freq-min-max".
Minimum clock value might be set to 100K by default.
Then MMC core should try to find the correct value from 400K to 100K.
So it just needs to set Maximum clock value.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
stop_cmdr should be set to values relevant to stop command.
It migth be assigned to values whatever there is mrq->stop or not.
Then it doesn't need to use dw_mci_prepare_command().
It's enough to use the prep_stop_abort for preparing stop command.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If DW_MMC_CARD_NO_USE_HOLD isn't set, it's usesd by default.
Enve if SDMMC_CMD_USB_HOLD_REG is set in prepare_command(), but it
doesn't set in pre_stop_abort().
To maintain the consistency, add the checking condition for this.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If there is no property "clock-freq-min-max", mmc->f_min should be set
to 400K by default. But Some SoC can be used 100K.
When 100K is used, MMC core will try to check from 400K to 100K.
Reported-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Jean-Nicolas Graux