We should use i2c_get_clientdata() to get the codec private structure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
After the device has been reset we need to repeat the same
initialisation we do on probe to make sure that the device is in
a known state.
Tested-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
On a mx6qsabrelite board the following error happens on probe:
sgtl5000: probe of 0-000a failed with error -5
imx-sgtl5000 sound.13: ASoC: CODEC (null) not registered
imx-sgtl5000 sound.13: snd_soc_register_card failed (-517)
platform sound.13: Driver imx-sgtl5000 requests probe defer
Prior to reading the codec ID we need to turn the SYS_MCLK clock, so let's
enable the codec clock inside sgtl5000_i2c_probe().
Also remove the codec clock enable/disable functions from the machine driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
FireWire upper layer drivers are converted from generic
struct driver.probe() and .remove()
to bus-specific
struct fw_driver.probe() and .remove().
The new .probe() adds a const struct ieee1394_device_id *id argument,
indicating the entry in the driver's device identifiers table which
matched the fw_unit to be probed. This new argument is used by the
snd-firewire-speakers driver to look up device-specific parameters and
methods. There is at least one other FireWire audio driver currently in
development in which this will be useful too.
The new .remove() drops the unused error return code.
Although all in-tree drivers are being converted to the new methods,
support for the old methods is left in place in this commit. This
allows public developer trees to merge this commit and then move to the
new fw_driver methods.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Clemens Ladisch <clemens@ladisch.de> (for sound/firewire/)
Cc: Peter Hurley <peter@hurleysoftware.com> (for drivers/staging/fwserial/)
When calling snd_soc_dapm_sync(), it eventually tries to lock the same mutex
already locked in snd_soc_dapm_put_volsw_aic3x() and a deadlock occurs. By
moving the mutex unlock to just before snd_soc_dapm_sync(), this deadlock is
prevented. This problem was introduced in Linux 3.5
Signed-off-by: Andreas Irestål <Andreas.Irestal@axis.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Even though they are virtual widgets DAI widgets still get counted for the
DAPM context power management so we can't just use the active state to
check if they should be powered as they may not be part of a complete path.
Instead split them into input and output widgets and do the same power
checks as we perform on AIFs.
Reported-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Document the device tree binding for the WM8962 codec, and modify the
driver to extract platform data from the device tree, if present.
Based on work of WM8903 by Stephen Warren <swarren@nvidia.com>
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For Intel Haswell chip, HDA controller and codec have
power well dependency from GPU side. This patch added support
to request/release power well in audio driver. Power save
feature should be enabled to get runtime power saving.
There's deadlock when request_module(i915) in azx_probe.
It looks like:
device_lock(audio pci device) -> azx_probe -> module_request
(or symbol_request) -> modprobe (userspace) -> i915 init ->
drm_pci_init -> pci_register_driver -> bus_add_driver -> driver_attach ->
which in turn tries all locks on pci bus, and when it tries the one on the
audio device, it will deadlock.
This patch introduce a work to store remaining probe stuff, and let
request_module run in safe work context.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is a preliminary work for the upcoming Haswell HDMI audio fixes.
azx_first_init() function can be safely called after the f/w loader,
since the f/w loader doesn't require the sound hardware initialization
beforehand. Moving it into azx_probe_continue() cleans up the code
flow a bit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The device can support runtime PM no matter whether it support
signal wakeup or not. For some chips like Haswell which doesnot
support PME by default, this patch let haswell Display HD-A controller
enter runtime suspend, and bring more power saving whith power-well
feature enabled.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Embed a copy of struct wm8962_pdata in stuct wm8962_priv
so that there's no need to check validity of pdata any more.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When a codec is powered off, some systems don't respond properly after
D3 FG transition, while the driver still expects the response and
tries to fall back to different modes (polling and single-cmd). When
the fallback happens, the driver stays in that mode, and falling back
to the single-cmd mode means it'll loose the unsol event handling,
too.
The unresponsiveness at D3 isn't too serious, thus this fallback is
mostly superfluous. We can gracefully ignore the error there so that
the driver keeps the normal operation mode.
This patch adds a new bit flag for codec read/write, set in the power
transition stage, which is notified to the controller driver via a new
bus->no_response_fallback flag.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_hda_codec_read(), snd_hda_codec_write() & co take the argument
"direct" that indicates whether the given NID is a direct reference or
an indirect reference. However, the indirect reference is practically
unimplemented and never exists. And moreover, we don't need the
indication of indirect reference at this high level, as NID can be
represented in 16bit values at this point.
Meanwhile, there are some cases where it'd be nice to give some
operational options to these functions. So, we can reuse this
argument as a new bit flag! Pretty frugal, eh?
All callers so far pass zero to this argument, thus there is no
behavior change by this replacement.
The real usage of this new bit option will be added in the following
patches.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently HDMI codec driver sets the hard dependency (reverse
selection) on CONFIG_SND_DYNAMIC_MINORS because the recent codecs may
support more than two PCMs. But, this doesn't mean that we need
always this option, since there can be a single PCM stream even with
the modern codecs.
This patch drops the hard dependency again but give more sensible
error message when no enough PCMs are available due to the lack of
this option.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Otherwise the functions will be defined but unreferenced when runtime PM
is disabled, generating warnings.
Signed-off-by: Mark Brown <broonie@linaro.org>
When the regulators have been disabled mark the device as cache only so
that we don't try to interact with the hardware.
Signed-off-by: Mark Brown <broonie@linaro.org>
to support HDMI on CSR SiRFprimaII and atlasVI, we need one more HDMI pseudo
codec, rather than add a new driver, we can make omap HDMI codec common for
other SoCs as well. then the omap-hdmi codec becomes a generic HDMI pseudo-
codec as HDMI audio features depend on HDMI specification not on SoCs.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
All sources and sinks should enable SYSCLK.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
* for-linus: (778 commits)
ALSA: usb-audio - Fix invalid volume resolution on Logitech HD webcam c270
ALSA: usb-audio - Apply Logitech QuickCam Pro 9000 quirk only to audio iface
ALSA: hda/via - Clean up duplicated codes
ALSA: hda/via - Fix wrongly cleared pins after suspend on VT1802
ALSA: hda - Add keep_eapd_on flag to generic parser
ALSA: hda - Allow setting automute/automic hooks after parsing
ALSA: hda/via - Disable broken dynamic power control
ALSA: usb-audio: fix Roland/Cakewalk UM-3G support
ALSA: hda - Add headset quirk for two Dell machines
ALSA: hda - add dock support for Thinkpad T431s
ALSA: sis7019: fix error return code in sis_chip_create()
ASoC: cs42l52: fix default value for MASTERA_VOL.
ASoC: wm8994: check for array index returned
ASoC: wm8994: Fix reporting of accessory removal on WM8958
ASoC: wm8994: use the correct pointer to get the control value
Linux 3.10-rc3
ipc/sem.c: Fix missing wakeups in do_smart_update_queue()
score: remove redundant kcore_list entries
ASoC: wm5110: Correct DSP4R Mixer control name
ARC: lazy dcache flush broke gdb in non-aliasing configs
...
This fixes the internal and external mic on Ordissimo EVE2, also known
as Malata PC-B1303.
We still don't know how to detect mic jack like Realtek's windows
driver.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tegra HW needs clocks etc. active when touching registers. Make sure they
are active during resume, by calling pm_runtime_get_sync() before touching
HW.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The VAG_POWER must be enabled after all other bits in CHIP_ANA_POWER
and disabled before any other bit in CHIP_ANA_POWER. See the SGTL5000
datasheet (Table 31, BIT 7, page 42-43). Failing to follow this order
will result in ugly loud "POP" noise at the end of playback.
To achieve such order, use the _PRE and _POST DAPM widgets to trigger
the power_vag_event, where the event type check has to be fixed
accordingly as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
When a DMA client requests and configures a DMA channel, it requests
data_width in Bytes. The DMA40 driver then swiftly converts it over to
the necessary register bit value. Unfortunately, for any subsequent
calculations we have to shift '1' by the bit pattern (1 << data_width)
times to make any sense of it.
This patch flips the semantics on its head and only converts the value
to its respective register bit pattern when writing to registers. This
way we can use the true data_width (in Bytes) value.
Cc: Dan Williams <djbw@fb.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Rabin Vincent <rabin@rab.in>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add tegra30_i2s_{suspend,resume}. These use regcache functions to
restore all HW registers after power loss during a suspend/resume cycle.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add tegra30_ahub_{suspend,resume}. These use regcache functions to
restore all HW registers after power loss during a suspend/resume cycle.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
'mcasp_dt_ids' is always compiled in. Hence of_match_ptr is not
necessary.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Both clear the IRQ as being a wake source when we are finished with it
and include a missing header file that is required.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The previous commit was written in the way to make the backport to
3.9.y easier, and left the duplicated open codes intentionally.
Now let's clean up the duplicated codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
VIA driver has a special suspend handling only for VT1802 to reduce
the pop noise. During the transition to the generic parser, the
behavior of snd_hda_set_pin_ctl() was also changed to modify the
cached values, too. And this caused a regression where the pin is
still cleared even after the resume (including the resume from power
save), resulting in the silent output.
The fix is simply to replace snd_hda_set_pin_ctl() with the explicit
call of snd_hda_codec_write() again.
Reported-by: Alex Riesen <raa.lkml@gmail.com>
Cc: <stable@vger.kernel.org> [v3.9]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
VT1802 codec seems to reset EAPD of other pins in the hardware level,
and this was another reason of the silent headphone output on some
machines. As a workaround, introduce a new flag indicating to keep
the EPAD on to the generic parser, and set it in patch_via.c.
Reported-by: Alex Riesen <raa.lkml@gmail.com>
Cc: <stable@vger.kernel.org> [v3.9]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some codec drivers (VIA codecs and some Realtek fixups) set the
automute and automic hooks after calling
snd_hda_gen_parse_auto_config(). In the current code, the hook
pointers are referred only in snd_hda_gen_parse_auto_config() and
passed to snd_hda_jack_detect_enable_callback(), thus changing the
hook values won't change the actually called callbacks properly.
This patch fixes this bug by setting the static functions as the
primary callback functions for the jack detection, and let them
calling the appropriate hooks dynamically.
Cc: <stable@vger.kernel.org> [v3.9]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the transition to the generic parser, the actual routes used
there don't match always with the assumed static paths in some
set_widgets_power_state callbacks. This results in the wrong power
setup in the end. As a temporary workaround, we need to disable the
calls together with the non-functional dynamic power control enum.
Reported-by: Alex Riesen <raa.lkml@gmail.com>
Cc: <stable@vger.kernel.org> [v3.9]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When declaring playback and capture capabilities check for both CODEC
side and CPU side support rather than only checking for CODEC side
support. While it is unusual some CPUs do have unidirectional DAIs.
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 927c9423dd (ALSA: usb-audio: add
Edirol UM-3G support) used a wrong quirk type, which would make the
driver refuse to attach with the error message "MIDIStreaming interface
descriptor not found".
Cc: <stable@vger.kernel.org> # 3.3 and later
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For systems which do not have a jack detection feature allow some debounce
to be specified before we perform accessory identification, improving
robustness without impacting button detection responsiveness.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Similarly to MADI, WordClock can also be at SingleSpeed while the card
is actually working at twice or four times this rate. If so, multiply
the base rate accordingly.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the DoubleSpeed or QuadSpeed bit is set, the SingleSpeed frequency
has to be multiplied accordingly. Since this functionality will be
required at least twice, refactor it into a separate function.
The second reference to the newly introduced hdspm_rate_multiplier()
will be in a separate commit.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This quirk is required for the headset mic to work on these
two machines.
BugLink: https://bugs.launchpad.net/bugs/1186170
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for TEA5757 tuner on MediaForte M56VAP sound+modem+radio card.
The GPIO connection type is automatically detected (like snd-fm801 driver).
Also add a safety subsystem vendor check to skip radio detection if vendor
differs from ESS (so we don't touch GPIOs on laptops).
Tested with SF64-PCE2 and M56VAP cards.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a model/fixup string "lenovo-dock", for Thinkpad T431s, to allow sound in docking station.
Tested on Lenovo T431s with ThinkPad Mini Dock Plus Series 3
Signed-off-by: Ebben Aries <earies@dscp.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix to return a negative error code in the pci_set_dma_mask() error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is loopback control within the audio interfaces, provide control of
this as there are some obscure scenarios where this could be used in
production.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that the bf5xx-i2s driver supports TDM mode and all users of the bf5xx-tdm
driver have been switch over to using the bf5xx-i2s driver there is no need to
keep the b5fxx-tdm driver around.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The bf5xx-i2s driver now has support for TDM mode and the bf5xx-tdm driver is
going to be removed soon, so switch the driver over to bf5xx-i2s.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The bf5xx-i2s driver now has support for TDM mode and the bf5xx-tdm driver is
going to be removed soon, so switch the driver over to bf5xx-i2s.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The bf5xx-i2s{,-pcm} and bf5xx-tdm{-pcm} drivers are nearly identical. Both are
for the same hardware each supporting a slight different subset of the hardware.
The bf5xx-i2s driver supports 2 channel I2S mode while the bf5xx-tdm driver
supports TDM mode and channel remapping. This patch adds support for TDM mode
and channel remapping to the bf5xx-i2s driver so that we'll eventually be able
to retire the bf5xx-tdm driver. Unfortunately the hardware is fixed to using 8
channels in TDM mode. The bf5xx-tdm driver jumps through a few hoops to make it
work well with other channel counts as well:
* Don't support mmap
* Translate between internal frame size (which is always 8 * sample_size)
and ALSA frame size (which depends on the channel count)
* Have special copy and silence callbacks which are aware of the mismatch
between internal and ALSA frame size
* Reduce the maximum buffer size to ensure that there is enough headroom for
dummy data.
The bf5xx-i2s driver is going to use the same mechanisms when being used int
TDM mode.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_pcm_lib_preallocate_pages_for_all() for pre-allocating the DMA buffers
instead of re-implementing the same functionality. Note that there is no need
to call snd_pcm_lib_free_pages_for_all() since the ALSA core takes care of this
for us.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is no need to always allocate the maximum buffer size. While we are at it
also pass errors returned by snd_pcm_lib_malloc_pages() on to the upper layers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since the hardware supports it there is no need to artificially limit this to
just being able to set the same mask for both tx and rx.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Using dev_{err,dbg} instead of pr_{error,debug} makes it easier to recognize
which device created the message.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The structs defined in these files are completely unused, so remove both the
structs and the files.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Support for omap2evm was removed in v3.0. But only one of its two
lines in this Makefile was removed. Remove the second line too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The DSPs IRQ should be a wake source as several of the possible
algorithms may run whilst the AP is asleepi and require to wake the AP
to push or pull more data, such as compressed playback.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Provide a bit of debounce to handle pathological cases with slow input
better by allowing the microphone detection to run for a bit longer.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A series of driver specific updates, none particularly critical, plus
one fix to the compressed API code to handle capture streams properly
which is very safe for mainline as there's no current users.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=BZaD
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v3.10
A series of driver specific updates, none particularly critical, plus
one fix to the compressed API code to handle capture streams properly
which is very safe for mainline as there's no current users.
Similarly like the previous commit for PCI drivers, remove
dev_set_drvdata(NULL) and pnp_set_drvdata(NULL) calls in ISA drivers
now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As drvdata is cleared to NULL at probe failure or at removal by the
driver core, we don't have to call pci_set_drvdata(pci, NULL) any
longer in each driver.
The only remaining pci_set_drvdata(NULL) is in azx_firmware_cb() in
hda_intel.c. Since this function itself releases the card instance,
we need to clear drvdata here as well, so that it won't be released
doubly in the remove callback.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The default register value for MASTERA_VOL is 0x00, the same as
MASTERB_VOL.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
The array 'drc_cfg' of size 3 may use index value -22 (EINVAL)
The array 'retune_mobile_cfg' of size 3 may use index value -22 (EINVAL)
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rename `dirty' to `set' as it is a bit more descriptive. A set
control is any control that has been set by the user. We need to ensure
that everytime we boot the DSP we sync out any controls that were
set.
We could at some point start keeping track of the default values of
the controls to suppress some of the device I/O.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current implementation of mop500_ab8500 allows for inconsistent sample
rate and channel count configuration between the playback and recording
interfaces, through in the hardware the two MSP controllers share
common clock and frame sync signals.
This patch adds the necessary code to ensure that the two device are
configure consistently. The check is added at machine driver level, as
how to lock DAI configuration depend of the actual hardware
implementation.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
During recent refactoring the code to report removal when MICDET reports
an absent microphone was removed, causing problems for systems which rely
solely on the MICDET for this functionality. Restore it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The newer HP laptops have SSID 103c:20xx and 103c:21xx, and these
usually have the mic-mute LED on Fn-F8. Let's enable it, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Ux500 has two equivalent enum for device id, one in platform_data and
one in a local header. Fix this by dropping the local one.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a missing include that was resulting in some sparse warning for
non-static structure without forward declaration.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Drop unused fields and structures from ux500_msp_i2s header file, as
those looks like leftover from a previous implementation of the driver.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Drop struct i2s_controller from the ux500 ASoC driver as right now it is
instantiated but not used anywhere. Also drop a mismatched
device_unregister in the process.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Define ab8500 codec operations structure on its own rather than inline
with snd_soc_dai_drivers to clean up the code and make the style
coherent with other codec drivers.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Drop pinctrl default/sleep state switching code, as it was breaking the
capture interface by putting the I2S pins in hi-z mode regardless of its
usage status, and not giving any real benefit.
Pinctrl default mode configuration is already managed automatically by a
specific pinctrl hog.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Apart from pure matching, the bindings also support setting the the
reset gpio line.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds a ASoC CODEC driver for the SSM2516. The SSM2516 is a stereo
Class-D audio amplifier with an I2S interface for audio in and a built-in
dynamic range control processor.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Currently ALSA supports up to 32 card instances when the dynamic minor
is used. While 32 cards are usually big enough for normal use cases,
there are sometimes weird requirements with more card support.
Actually, this limitation, 32, comes from the index option, where you
can pass the bit mask to assign the card. Other than that, we can
actually give more cards up to the minor number limits (currently 256,
which can be extended more, too).
This patch adds a new Kconfig to specify the max card numbers, and
changes a few places to accept more than 32 cards.
The only incompatibility with high card numbers would be the handling
of index option. The index option can be still used to pass the
bitmask for card assignments, but this works only up to 32 slots.
More than 32, no bitmask style option is available but only a single
slot can be specified via index option.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA core tries to add a suffix as "_1" automatically when the given
id string conflicts. The current code assumes implicitly that the max
card number is 16 so that the single hex "_X" suffix can be put.
However, with the dynamic device management, the card can be at most
32, so it can put even a non-hex character there. Also, when the max
card number is increased in future, this would result in worse.
This patch rewrites the code to add the suffix string in a simpler
(thus cleaner) way. It can support up to three digits, so it should
suffice for most requirements.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ops field of the snd_pcm_substream struct is never modified inside the ALSA
core. Making it const allows drivers to declare their snd_pcm_ops struct as
const.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pass a struct i2c_client * to adau1701_load_firmware directly to make
the code more readable.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Rafael Ignacio Zurita <rizurita@yahoo.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Stas Sergeev <stsp@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Check only the uppermost 16 bits instead of the whole 32 bits of
the version information. Do this because all firmware version tested
with this version information worked correctly and the strict check
causes problems for several users.
Signed-off-by: Torsten Schenk <torsten.schenk@zoho.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The power_list field is used when adding a widget to a power sequence list. Use
the same field when iterating the list using list_for_each_entry, otherwise
we'll see undefined behavior.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The mask should define the bits to change in the register, not the
bits to preserve.
This fixes the inadvertent changes of the "Headphone Analog Gain"
value during mute/unmute.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
McASP serial audio engine needs different rotation values on TX and RX
channels. Commit dde109fb46 ("ASoC: McASP: Fix data rotation for
playback. Enables 24bit audio playback") changed the calculation to fix
the playback format, but broke the capture stream by doing it for both
TXFMT and RXFMT.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org [3.9 only]
DFBM-CS320 is only one of bluetooth modules using CSR bluetooth chips,
we don't want everyone to have a seperate codec driver. anyway, the
feature of Bluetooth SCO is same on all platforms, so this patch
makes the DFBM-CS320 driver become a common BT SCO link driver.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Replace hard coded rx slot numbers from ab8500_codec_set_dai_tdm_slot
using the ones requested by the machine driver in rx_mask instead.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Replace hard-coded tx slot numbers from ab8500_codec_set_dai_tdm_slot
using the ones requested by the machine driver in tx_mask instead.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add callback to initialise the speaker in the core following the recent
changes to handling of integration with the thermal interrupts.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
On WM8958 and WM1811A separate control of the LRCLK inversion bit is
available for the DAC and ADC LRCLKs which for compatibility reasons is
done in a new register bit.
Since writes to each scheme have no effect on parts using the other just
always write to both for simplicity.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Samreen Nilofer <samreen.nilofer@intel.com>
request_threaded_irq() rejects calls which both do not specify a handler
(indicating that the primary IRQ handler should be used) and do not set
IRQF_ONESHOT because the combination is unsafe with level-triggered
interrupts. It is safe in this case, though, since max98090 IRQs are
edge-triggered and the interrupts aren't ACK'ed until the codec's IRQ
status register is read. Because of this, an IRQF_ONESHOT interrupt
doesn't really make a difference, but request one anyway in order to make
request_threaded_irq() happy.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pull devm usage cleanup from Wolfram Sang:
"Lately, I have been experimenting how to improve the devm interface to
make writing device drivers easier and less error prone while also
getting rid of its subtle issues. I think it has more potential but
still needs work and definately conistency, especiall in its usage.
The first thing I come up with is a low hanging fruit regarding
devm_ioremap_resouce(). This function already checks if the passed
resource is valid and gives an error message if not. So, we can
remove similar checks from the drivers and get rid of a bit of code
and a number of inconsistent error strings.
This series only removes the unneeded check iff devm_ioremap_resource
follows platform_get_resource directly. The previous version tried to
shuffle code if needed, too, what lead to an embarrasing bug. It
turned out to me that shuffling code for all cases found will make the
automated script too complex, so I am unsure if an automated cleanup
is the proper tool for this case. Removing the easy stuff seems
worthwhile to me, though.
Despite various architectures and platform dependencies, I managed to
compile test 45 out of 57 modified files locally using heuristics and
defconfigs."
Pulled because: 296 deletions, 0 additions.
* 'devm_no_resource_check' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (33 commits)
sound/soc/kirkwood: don't check resource with devm_ioremap_resource
sound/soc/fsl: don't check resource with devm_ioremap_resource
arch/mips/lantiq/xway: don't check resource with devm_ioremap_resource
arch/arm/plat-samsung: don't check resource with devm_ioremap_resource
arch/arm/mach-tegra: don't check resource with devm_ioremap_resource
drivers/watchdog: don't check resource with devm_ioremap_resource
drivers/w1/masters: don't check resource with devm_ioremap_resource
drivers/video/omap2/dss: don't check resource with devm_ioremap_resource
drivers/video/omap2: don't check resource with devm_ioremap_resource
drivers/usb/phy: don't check resource with devm_ioremap_resource
drivers/usb/host: don't check resource with devm_ioremap_resource
drivers/usb/gadget: don't check resource with devm_ioremap_resource
drivers/usb/chipidea: don't check resource with devm_ioremap_resource
drivers/thermal: don't check resource with devm_ioremap_resource
drivers/staging/nvec: don't check resource with devm_ioremap_resource
drivers/staging/dwc2: don't check resource with devm_ioremap_resource
drivers/spi: don't check resource with devm_ioremap_resource
drivers/rtc: don't check resource with devm_ioremap_resource
drivers/pwm: don't check resource with devm_ioremap_resource
drivers/pinctrl: don't check resource with devm_ioremap_resource
...
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The max98090 driver currently treats the digital mic enable as a supply
on the record path, causing the digital mic enable to always be turned on
when attempting to record. This is incorrect, however, since the digital
mic enable is also a mux control where 0 selects the ADC output as input
to the record-path DSP and 1 selects the digital mic. This patch adds
a virtual DMIC mux to the reocrd path so that we can switch between the
ADC and the digital mic for recording.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add HD Audio Device PCI ID for the Intel BayTrail platform.
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
freqshift is only set for the data endpoint and syncmaxsize is only set
for the sync endpoint. This results in a syncmaxsize of zero used in the
proc output feedback format calculation, which gives a feedback format
incorrectly shown as 8.16 for UAC2 devices.
As neither the data nor the sync endpoint gives all the relevant
content, output the two combined.
Also remove the sync_endpoint "packet size" which is always zero
and the sync_endpoint "momentary freq" which is constant.
Tested with UAC2 async and UAC1 adaptive, not tested with UAC1 async.
Reported-by: B. Zhang <bb.zhang@free.fr>
Signed-off-by: Torstein Hegge <hegge@resisty.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Either one or a combination of commits 81e5d86
"Register i2c devices from device-tree" and 3a3dd01
"Improve detection of devices from device-tree" broke sound on
PowerBook6,5 machines.
Fix it by adding an entry to the new driver to match PowerBook6,5
machines.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few small driver-specific fixes, none of them especially crippling.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=GQj5
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.10
A few small driver-specific fixes, none of them especially crippling.
When an inactive path is powered down with spec->power_down_unused
flag, we should check the activity of each widget in the path whether
it's still referred from any active path.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With imx-pcm-dma moving to generic dmaengine pcm driver and the removal
of imx-pcm-audio/imx-fiq-pcm-audio platform device use, now imx-pcm
driver contains a few functions that are only used by imx-pcm-fiq.c.
Move these functions into imx-pcm-fiq.c and remove imx-pcm.c completely.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than instantiating imx-fiq-pcm-audio to call imx_pcm_fiq_init(),
imx-ssi can just directly call it to save the use of imx-fiq-pcm-audio.
With this change, imx-ssi becomes not only a cpu DAI but also a platform
device, so updates platform device setup in eukrea-tlv320, phycore-ac97
and wm1133-ev1 accordingly.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Create function imx_pcm_fiq_exit() to be paired with imx_pcm_fiq_init()
just like the pair of imx_pcm_dma_init() and imx_pcm_dma_exit().
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than instantiating imx-pcm-audio to call imx_pcm_dma_init(),
imx-ssi can just directly call it to save the use of imx-pcm-audio.
With this change, imx-ssi becomes not only a cpu DAI but also a
platform device, so updates platform device setup in imx-mc13783 and
mx27vis-aic32x4 accordingly.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than instantiating imx-pcm-audio to call imx_pcm_dma_init(),
fsl_ssi can just directly call it to save the use of imx-pcm-audio.
With this change, fsl_ssi becomes not only a cpu DAI but also a platform
device, so updates platform device setup in imx-sgtl5000 accordingly.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Support for PXA95x was removed in v3.8. This means that the Kconfig
symbols MACH_SAARB and MACH_TAVOREVB3 are no longer available. This
leaves the SoC Audio support for Marvell Saarb and Marvell Tavor EVB3
unbuildable. Remove these drivers too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The pcm3008_codec struct is not used outside of davinci-sffsdr.c, so make it
static.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The sn95031_codec struct is not used outside of sn95031.c, so make it static.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The mop500_dai_links struct is not used outside of mop500.c, so make it static.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The mop500_ab8500_startup(), the mop500_ab8500_shutdown() and the
mop500_ab8500_hw_params() function are not used outside of mop500_ab8500, so
make them static.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The bf5xx_tdm_pcm_ops struct is only used in bf5xx-tdm-pcm.c, so make it static.
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The mmp_sspa_dai struct is only used in mmp-sspa.c, so make it static.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The mmp_pcm_ops and mmp_soc_platform struct as well as the mmp_pcm_new()
function are only used in mmp-pcm.c, so make them static.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The spdif_soc_dai_probe function is only used in spdif_out.c, so make it static.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The spdif_in_dai struct is not used outside of spdif_in.c, so make it static.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The kirkwood_dma_ops struct is not used outside of kirkwood-dma.c, so make it
static.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The ep93xx_i2s_dma_data struct is not used outside of ep93xx-i2s.c, so make it
static.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
kasprintf calculates the size of the result string, allocates a buffer large
enough to hold the string and then performs the format string operation. There
are a couple of places in ASoC where these three steps are done by hand and
where kasprintf can be used instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We use the same code to initialize the runtime pcm based on the
snd_soc_pcm_stream struct on both the playback and capture path. Factor this
code into a helper function to make things a bit more tidy.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
snd_soc_set_runtime_hwparams() is the only PCM related function that lives in
soc-core.c. All other PCM related functions live in soc-pcm.c, so move
snd_soc_set_runtime_hwparams() over as well for a bit more consistency.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There are two return paths which don't kfree(name).
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that all of the Tegra device trees have been updated to represent
the required audio clocks, remove the compatibility code from the Tegra
ASoC utility code, and always use clk_get() rather than clk_get_sys().
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the generic dmaengine PCM driver instead of a custom implementation.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This allows us to access the DAI DMA data when we create the PCM. We'll use
this when converting ep39xx to generic DMA engine PCM driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit d4702b189c ("sound: Fix make allmodconfig on MIPS") added a
(negative) dependency on ISA_DMA_SUPPORT_BROKEN. Since that Kconfig
symbol doesn't exist, this dependency will always evaluate to true.
Apparently GENERIC_ISA_DMA_SUPPORT_BROKEN was meant to be used here.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With mxs-dma converted to generic DMA bindings, let's move mxs-pcm to
use it by removing flages SND_DMAENGINE_PCM_FLAG_NO_DT and
SND_DMAENGINE_PCM_FLAG_COMPAT. As the result, those mxs custom dma
params code can be removed now.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Later WM8994 devices support an enhanced accuracy FLL divisor mode called
EFS which allows more precise selection of fractional source to output
ratios. Support this on relevant devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In preparation to switching the jz4740 clk driver to the common clk framework
update the clk enable/disable calls to clk_prepare_enable/clk_disable_unprepare.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the AB8500 user manual AD to Slot register multiplexer
accept values from 0 to 15 where:
0 to 7 corresponds to AD_OUTx slots
8 to 11 corresponds to zero output
12 to 15 sets the output in tristate mode
Update enum_ad_to_slot_map array to reflect this definition.
This also allows alsamixer to properly display the default
configuration, as all controls are set to tristate (=12) at reset.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Drop ab8500 clock gating widgets from mop500_ab8500_ctrls, as these bits
are already controlled by ab8500 codec driver and should not be exposed
to the user.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Update mop500_ab8500_machine_init to register mop500_ab8500_ctrls as
card control instead of codec control, as it only contains
SOC_DAPM_PIN_SWITCH definitions.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Drop dev_set_drvdata as this is handled in the core and use
devm_request_and_ioremap instead of devm_ioremap to properly register the
address range used
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the generic dmaengine PCM driver instead of a custom implementation.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This allows us to access the DAI DMA data when we create the PCM. We'll use
this when converting spear to generic DMA engine PCM driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add devicetree support for this dummy audio soc driver.
Signed-off-by: Michal Bachraty <michal.bachraty@streamunlimited.com>
Signed-off-by: Marek Belisko <marek.belisko@streamunlimited.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add devicetree support for this dummy audio soc driver.
Signed-off-by: Michal Bachraty <michal.bachraty@streamunlimited.com>
Signed-off-by: Marek Belisko <marek.belisko@streamunlimited.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Transceiver usually means receiver + transmitter. This codec can do only
transmit. Update driver accordingly.
Signed-off-by: Marek Belisko <marek.belisko@streamunlimited.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
After a 'reboot' command in Linux or after pressing the system's reset button
the sgtl5000 driver fails to probe:
sgtl5000 0-000a: Device with ID register ffff is not a sgtl5000
sgtl5000 0-000a: ASoC: failed to probe CODEC -19
imx-sgtl5000 sound.12: ASoC: failed to instantiate card -19
imx-sgtl5000 sound.12: snd_soc_register_card failed (-19)
sgtl5000 codec does not have a reset line, nor a reset command in software, so
after a system reset the codec does not contain the default register values
from sgtl5000_reg_defaults[] anymore, as these are only valid after a
power-on-reset cycle.
Fix this issue by explicitly reading all the reset register values from
sgtl5000_reg_defaults[] and writing them back into sgtl5000 to ensure a sane
state.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The usual place for reading chip ID is inside i2c_probe, so move it there and
also convert it to regmap.
sgtl5000_enable_regulators() needs to read the chip revision, so keep the
revision check there.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It makes no sense to hardcode the I2C bus into the codec_name field.
cpu_dai_name and platform_name are also overwritten later in
mxs_sgtl5000_probe_dt().
So remove the three fields, as mxs platform is dt-only platform.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Variable 'ret' is not needed here, so just remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The list below the comment relates to sgtl5000 registers addresses, so change
the comment to improve the description.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for handling pinctrl.
So remove devm_pinctrl_get_select_default() from the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for handling pinctrl.
So remove devm_pinctrl_get_select_default() from the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It makes no sense to hardcode the I2C bus into the codec_name field.
cpu_dai_name and platform_name are also overwritten later in
mxs_sgtl5000_probe_dt().
So remove the three fields, as mxs platform is dt-only platform.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Variable 'ret' is not needed here, so just remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Return on success instead of entering the error path.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some devices may benefit from being able to start some parts of the widget
power up/down sequence earlier on in the sequence than the point at which
the final power state is committed. Support these by providing events which
are called before any power state changes are done.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Since commit ab78029 (drivers/pinctrl: grab default handles from device
core) we can rely on device core for handling pinctrl so remove
devm_pinctrl_get_select_default() from the driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Add initial support for runtime tuning for the ADSP cores. This
is achieved by exposing the coefficient configuration blocks as
ALSA binary controls.
The current code assumes that no controls on the DSP are volatile.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This contains small fixes since the previous pull request:
- A few regression fixes and small updates of HD-audio
- Yet another fix for Haswell HDMI audio
- A copule of trivial fixes in ASoC McASP, DPAM and WM8994
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABAgAGBQJRjOOfAAoJEGwxgFQ9KSmkzE8P/iX7Tz8F7DCTJnbE6W617fwI
z9weFqy7D/f6pTlMZrfzVCFJQBcACYLxN5OxfPDNu4zMao1Cki6ngococ6QBRMl/
bSu02pM3N2EGQQU4emQYfgR6+ZelUlVDS441jmIz6JOQYQql+eZZnO1XxWb0fHQC
MtHcxWLMhuXIcgSDeYeg+wQZjM/XxeN/AYA8Lnn8EEwoNV6vrZw4slOm8eC9qQnb
uqLjrivhcJpARetl/n5aPdIbtplkUVUAeyZnK6O4NHsN7AqBQ2RXSpPTTj4DV+fN
pN0Ah39eDNcF/zM0JqcDheSXP7MkB7s7kRcZOEmPwNSgCXfhjdwPDd4Si2y5tTbI
NMIZUawEdx47NkZDmyGRHyOQLixkMC/+qPQcD7cAof5WJAygpBAyU9WlOEVJ9MOZ
ytA0S+RWW05+jh5tiYHI+pjVl1TcN/ltgMsyBu+3owI4jQQs9LyIYR+IM4QkhpfE
gNDeDV6Do0xL0LSnPfYwgxV+H0oSWrRrUOlgEEeuyXBLcnIqJfUl+Y4n7afwO+xz
04izx1SUdp4dQ9Fo2/jInVn/EhQwwpw361yNUHtozFCh4ETNatBGiXIvWyLSW4FS
j9d+aNIZR4CtZ28+wymFSw6yiqLkJArNoUNgcJcKATgeqg6CUa+ZdYi6gkirp+gk
sU+bSxrxp4dv5hOj+rIF
=DMsb
-----END PGP SIGNATURE-----
Merge tag 'sound-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This contains small fixes since the previous pull request:
- A few regression fixes and small updates of HD-audio
- Yet another fix for Haswell HDMI audio
- A copule of trivial fixes in ASoC McASP, DPAM and WM8994"
* tag 'sound-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
Revert "ALSA: hda - Don't set up active streams twice"
ALSA: Add comment for control TLV API
ALSA: hda - Apply pin-enablement workaround to all Haswell HDMI codecs
ALSA: HDA: Fix Oops caused by dereference NULL pointer
ALSA: mips/sgio2audio: Remove redundant platform_set_drvdata()
ALSA: mips/hal2: Remove redundant platform_set_drvdata()
ALSA: hda - Fix 3.9 regression of EAPD init on Conexant codecs
sound: Fix make allmodconfig on MIPS
ALSA: hda - Fix system panic when DMA > 40 bits for Nvidia audio controllers
ALSA: atmel: Remove redundant platform_set_drvdata()
ASoC: McASP: Fix receive clock polarity in DAIFMT_NB_NF mode.
ASoC: wm8994: missing break in wm8994_aif3_hw_params()
ASoC: McASP: Add pins output direction for rx clocks when configured in CBS_CFS format
ASoC: dapm: use clk_prepare_enable and clk_disable_unprepare
This reverts commit affdb62b81.
The commit introduced a regression with AD codecs where the stream is
always clean up. Since the patch is just a minor optimization and
reverting the commit fixes the issue, let's just revert it.
Reported-and-tested-by: Michael Burian <michael.burian@sbg.at>
Cc: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When set dmic_samplephase and dmic_clk_rate bits for dmic_cfg,
current code checks pdata->dmic_data_sel which is wrong.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
AD slots definitions for ab8500 codec were erroneously swapped between
even and odd channels. Fix this by swapping the definitions to be
coherent with the channel number.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is a revised patch based on Mengdong Lin's fix patch, which is a
supplement to a previous patch [1611a9c9: ALSA: hda - Add fixup for
Haswell to enable all pin and convertor widgets].
Some Haswell BIOS will disable the 2nd and 3rd pin/covertor widgets
when the HD-A controller changes state from D3 to D0. So when the
controller resumes after a system or runtime suspend, these widgets
are disabled and programming these widgets to D0 will cause H/W error
and codec will not respond.
In addition, we found out that some BIOS disables the pins at S3
although it shows up at boot. This confuses the driver utterly, and
the hardware falls into the fatal communication error like the above.
So in this patch, we apply intel_haswell_enable_all_pins() not only as
a fixup to a certain device (with 8086:2010) but to all Haswell
machines. The codec driver basically assumes that all pins are
exposed, so it's anyway better to see them from the beginning. Even
if all pins and converters are shown by this call, there should be no
regression in practice: the pin default configurations are still kept,
thus the disabled pins are handled as disabled by the driver
properly.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix to return -ENOMEM in the memory malloc of 'out' and 'img_swap' error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The interrupt handler azx_interrupt will call azx_update_rirb,
which may call snd_hda_queue_unsol_event, snd_hda_queue_unsol_event
will dereference chip->bus pointer.
The problem is we alloc chip->bus in azx_codec_create
which will be called after we enable IRQ and enable unsolicited
event in azx_probe.
This will cause Oops due dereference NULL pointer. I meet it, good luck:)
[Rearranged the NULL check before the tracepoint and added another
NULL check of bus->workq -- tiwai]
Signed-off-by: Wang YanQing <udknight@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Vivien Chappelier <vivien.chappelier@linux-mips.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.fanken.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The older Conexant codecs have up to two EAPDs and these are supposed
to be rather statically turned on. The new generic parser code
assumes the dynamic on/off per path usage, thus it resulted in the
silent output on some machines.
This patch fixes the problem by simply assuming the static EAPD on for
such old Conexant codecs as we did until 3.8 kernel.
Reported-and-tested-by: Christopher K. <c.krooss@gmail.com>
Cc: <stable@vger.kernel.org> [v3.9]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Mostly many small changes spread as seen in diffstat in sound/*
directory by this update. A significant change in the subsystem level
is the introduction of snd_soc_component, which will help more generic
handling of SoC and off-SoC components.
Also, snd_BUG_ON() macro is enabled unconditionally now due to its
misuses, so people might hit kernel warnings (it's a good thing for
us).
- compress-offload: support for capture by Charles Keepax
- HD-audio: codec delay support by Dylan Reid
- HD-audio: improvements/fixes in generic parser: better headphone mic
and headset mic support, jack_modes hint consolidation, proper beep
attach/detachment, generalized power filter controls by David
Henningsson, et al
- HD-audio: Improved management of HDMI codec pins/converters
- HD-audio: Better pin/DAC assignment for VIA codecs
- HD-audio: Haswell HDMI workarounds
- HD-audio: ALC268 codec support, a few new quirks for Chromebooks
- USB: regression fixes: USB-MIDI autopm fix, the recent ISO latency
fix by Clemens Ladisch
- USB: support for DSD formats by Daniel Mack
- USB: A few UAC2 device endian/cock fixes by Eldad Zack
- USB: quirks for Emu 192kHz support, Novation Twitch DJ controller,
Yamaha THRxx devices
- HDSPM: updates for TCO controls by Adrian Knoth
- ASoC: Add a snd_soc_component object type for generic handling of
SoC and off-SoC components by Kuninori Morimoto,
- dmaengine: a large set of cleanups and conversions by Lars-Peter
Clausen
- ASoC DAPM: performance optimizations from Ryo Tsutsui
- ASoC DAPM: support for mixer control sharing by Stephen Warren
- ASoC: multiplatform ARM cleanups from Arnd Bergmann
- ASoC: new codec drivers for AK5385 and TAS5086 from Daniel Mack
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=sYiI
-----END PGP SIGNATURE-----
Merge tag 'sound-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"Mostly many small changes spread as seen in diffstat in sound/*
directory by this update. A significant change in the subsystem level
is the introduction of snd_soc_component, which will help more generic
handling of SoC and off-SoC components.
Also, snd_BUG_ON() macro is enabled unconditionally now due to its
misuses, so people might hit kernel warnings (it's a good thing for
us).
- compress-offload: support for capture by Charles Keepax
- HD-audio: codec delay support by Dylan Reid
- HD-audio: improvements/fixes in generic parser: better headphone
mic and headset mic support, jack_modes hint consolidation, proper
beep attach/detachment, generalized power filter controls by David
Henningsson, et al
- HD-audio: Improved management of HDMI codec pins/converters
- HD-audio: Better pin/DAC assignment for VIA codecs
- HD-audio: Haswell HDMI workarounds
- HD-audio: ALC268 codec support, a few new quirks for Chromebooks
- USB: regression fixes: USB-MIDI autopm fix, the recent ISO latency
fix by Clemens Ladisch
- USB: support for DSD formats by Daniel Mack
- USB: A few UAC2 device endian/cock fixes by Eldad Zack
- USB: quirks for Emu 192kHz support, Novation Twitch DJ controller,
Yamaha THRxx devices
- HDSPM: updates for TCO controls by Adrian Knoth
- ASoC: Add a snd_soc_component object type for generic handling of
SoC and off-SoC components by Kuninori Morimoto,
- dmaengine: a large set of cleanups and conversions by Lars-Peter
Clausen
- ASoC DAPM: performance optimizations from Ryo Tsutsui
- ASoC DAPM: support for mixer control sharing by Stephen Warren
- ASoC: multiplatform ARM cleanups from Arnd Bergmann
- ASoC: new codec drivers for AK5385 and TAS5086 from Daniel Mack"
* tag 'sound-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (315 commits)
ALSA: usb-audio: caiaq: fix endianness bug in snd_usb_caiaq_maschine_dispatch
ALSA: asihpi: add format support check in snd_card_asihpi_capture_formats
ALSA: pcm_format_to_bits strong-typed conversion
ALSA: compress: fix the states to check for allowing read
ALSA: hda - Move Thinkpad X220 to use auto parser
ALSA: USB: adjust for changed 3.8 USB API
ALSA: usb - Avoid unnecessary sample rate changes on USB 2.0 clock sources
sound: oss/dmabuf: use dma_map_single
ALSA: ali5451: use mdelay instead of large udelay constants
ALSA: hda - Add the support for ALC286 codec
ALSA: usb-audio: USB quirk for Yamaha THR10C
ALSA: usb-audio: USB quirk for Yamaha THR5A
ALSA: usb-audio: USB quirk for Yamaha THR10
ALSA: usb-audio: Fix autopm error during probing
ALSA: snd-usb: try harder to find USB_DT_CS_ENDPOINT
ALSA: sound kconfig typo
ALSA: emu10k1: Fix dock firmware loading
ASoC: ux500: forward declare msp_i2s_platform_data
ASoC: davinci-mcasp: Add Support BCLK-to-LRCLK ratio for TDM modes
ASoC: davinci-pcm, davinci-mcasp: Clean up active_serializers
...
The compile of soundcard.c is broken on MIPS when allmodconfig is used
because of the missing MAX_DMA_CHANNELS definition. As a simple
workaround, just add a Kconfig dependency.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The audio driver mistakenly allows 64 bit addresses to be created for
the audio driver on Nvidia GPUs. Unfortunately, the hardware normally
only supports up to 40 bits of DMA. This can cause system panics as
well as misdirected data when the address is > 40 bits as the upper
part the address is truncated.
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Mike Habeck <habeck@sgi.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few more bug fixes, the DAPM clock fix is actually a driver specific
one since currently there's only one user of the clock support due to
the problems relying on the clock API.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJRg3/MAAoJELSic+t+oim9W+cP/3NERwICTNvllNOrZXii7akJ
DnzzIaw0fEJ2+hIXJzU/lEI/KjqIT7SADQRWg+eid8ZrjaUB6LXUPPuv67V4TseD
1+8ClQp1cDg1KepBcD2S1liVjPKvW64IpXwZNgLGigW6PP21yK8+DoQvVKPVB+sP
q72jntTzy9qWenmjygpPEYDeOfe5EM7hAaa2tFuYIPEL+EkMOXXvjx8ojylwQV6V
5xFQ+CBSS8WHz7CKlawF3JH8TkcFGZNT9Hibhv1fpGM+iJDCsh/+MNiBwOpO+1wk
eCJSiCWWTGgVK+3AvlSIQr8ml0EDEbS8Aq6bbJb9w4wgV65oFt2hOxOpkcK/8NcP
qnKNYc3nRQsb3H+dObMdQNPWDjOfwsolKUOjetxosRIq4Pzm8afY96gu06EqTnw9
XYXqoSAVpCuPDpmlu87Lajoj4T5XNq3G7ONAMpsAfMrl/xxmV11Wrs4/7S0o3Csb
tNhO5XjLbFNTw9nVT6qZQViH7Bm1ItDM2B/tLb1yqnlgBAjNW/WlUyFg4bE4Qeyr
hUg7DwvYPSVnr25t8RmPMmB2MdD4N+PfRy+aIEIuE9KMeYUTPVr5kFdDP7uA7Yw2
Dn7lmAdDEq33zfTGYhGWs87IdxhD3VyEWveR6alrtBW0LS7ArtsPlWKhA074XuJj
AmAU6RS3+75nymA9ucY+
=WQzu
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.10
A few more bug fixes, the DAPM clock fix is actually a driver specific
one since currently there's only one user of the clock support due to
the problems relying on the clock API.
According documentation bit ACLKRPOL is set to 0 (receiver samples data
on falling edge) and when set to 1 (receiver samples data on rising edge).
I2S data are always sampled on falling edge and valid during rising edge
of bit clock. So in case of capture data transmitter sample data on falling
edge and macsp must read then on rising edge.
Signed-off-by: Marek Belisko <marek.belisko@streamunlimited.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
More multiplatform enablement for ARM platforms. The ones converted in
this branch are:
- bcm2835
- cns3xxx
- sirf
- nomadik
- msx
- spear
- tegra
- ux500
We're getting close to having most of them converted!
One of the larger platforms remaining is Samsung Exynos, and there are
a bunch of supporting patches in this merge window for it. There was a
patch in this branch to a early version of multiplatform conversion,
but it ended up being reverted due to need of more bake time. The
revert commit is part of the branch since it would have required
rebasing multiple dependent branches and they were stable by then.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4hSo
-----END PGP SIGNATURE-----
Merge tag 'multiplatform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform updates from Olof Johansson:
"More multiplatform enablement for ARM platforms. The ones converted
in this branch are:
- bcm2835
- cns3xxx
- sirf
- nomadik
- msx
- spear
- tegra
- ux500
We're getting close to having most of them converted!
One of the larger platforms remaining is Samsung Exynos, and there are
a bunch of supporting patches in this merge window for it. There was
a patch in this branch to a early version of multiplatform conversion,
but it ended up being reverted due to need of more bake time. The
revert commit is part of the branch since it would have required
rebasing multiple dependent branches and they were stable by then"
* tag 'multiplatform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (70 commits)
mmc: sdhci-s3c: Fix operation on non-single image Samsung platforms
clocksource: nomadik-mtu: fix up clocksource/timer
Revert "ARM: exynos: enable multiplatform support"
ARM: SPEAr13xx: Fix typo "ARCH_HAVE_CPUFREQ"
ARM: exynos: enable multiplatform support
rtc: s3c: make header file local
mtd: onenand/samsung: make regs-onenand.h file local
thermal/exynos: remove unnecessary header inclusions
mmc: sdhci-s3c: remove platform dependencies
ARM: samsung: move mfc device definition to s5p-dev-mfc.c
ARM: exynos: move debug-macro.S to include/debug/
ARM: exynos: prepare for sparse IRQ
ARM: exynos: introduce EXYNOS_ATAGS symbol
ARM: tegra: build assembly files with -march=armv7-a
ARM: Push selects for TWD/SCU into machine entries
ARM: ux500: build hotplug.o for ARMv7-a
ARM: ux500: move to multiplatform
ARM: ux500: make remaining headers local
ARM: ux500: make irqs.h local to platform
ARM: ux500: get rid of <mach/[hardware|db8500-regs].h>
...
Here is a collection of cleanup patches. Among the pieces that stand out are:
- The deletion of h720x platforms
- Split of at91 non-dt platforms to their own Kconfig file to keep them separate
- General cleanups and refactoring of i.MX and MXS platforms
- Some restructuring of clock tables for OMAP
- Convertion of PMC driver for Tegra to dt-only
- Some renames of sunxi -> sun4i (Allwinner A10)
- ... plus a bunch of other stuff that I haven't mentioned
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=xCAx
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanup from Olof Johansson:
"Here is a collection of cleanup patches. Among the pieces that stand
out are:
- The deletion of h720x platforms
- Split of at91 non-dt platforms to their own Kconfig file to keep
them separate
- General cleanups and refactoring of i.MX and MXS platforms
- Some restructuring of clock tables for OMAP
- Convertion of PMC driver for Tegra to dt-only
- Some renames of sunxi -> sun4i (Allwinner A10)
- ... plus a bunch of other stuff that I haven't mentioned"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (119 commits)
ARM: i.MX: remove unused ARCH_* configs
ARM i.MX53: remove platform ahci support
ARM: sunxi: Rework the restart code
irqchip: sunxi: Rename sunxi to sun4i
irqchip: sunxi: Make use of the IRQCHIP_DECLARE macro
clocksource: sunxi: Rename sunxi to sun4i
clocksource: sunxi: make use of CLKSRC_OF
clocksource: sunxi: Cleanup the timer code
ARM: at91: remove trailing semicolon from macros
ARM: at91/setup: fix trivial typos
ARM: EXYNOS: remove "config EXYNOS_DEV_DRM"
ARM: EXYNOS: change the name of USB ohci header
ARM: SAMSUNG: Remove unnecessary code for dma
ARM: S3C24XX: Remove unused GPIO drive strength register definitions
ARM: OMAP4+: PM: Restore CPU power state to ON with clockdomain force wakeup method
ARM: S3C24XX: Removed unneeded dependency on CPU_S3C2412
ARM: S3C24XX: Removed unneeded dependency on CPU_S3C2410
ARM: S3C24XX: Removed unneeded dependency on ARCH_S3C24XX for boards
ARM: SAMSUNG: Fix typo "CONFIG_SAMSUNG_DEV_RTC"
ARM: S5P64X0: Fix typo "CONFIG_S5P64X0_SETUP_SDHCI"
...
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
The missing break here means that we always return early and the
function is a no-op.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
When McASP is bit clock and frame clock master enable pin output for rx clocks.
Signed-off-by: Marek Belisko <marek.belisko@streamunlimited.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Update dapm_clock_event to use clk_prepare_enable and
clk_disable_unprepare.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pull media update from Mauro Carvalho Chehab:
- OF documentation and patches at core and drivers, to be used by for
embedded media systems
- some I2C drivers used on go7007 were rewritten/promoted from staging:
sony-btf-mpx, tw2804, tw9903, tw9906, wis-ov7640, wis-uda1342
- add fimc-is driver (Exynos)
- add a new radio driver: radio-si476x
- add a two new tuners: r820t and tuner_it913x
- split camera code on em28xx driver and add more models
- the cypress firmware load is used outside dvb usb drivers. So, move
it to a common directory to make easier to re-use it
- siano media driver updated to work with sms2270 devices
- several work done in order to promote go7007 and solo6x1x out of
staging (still, there are some pending issues)
- several API compliance fixes at v4l2 drivers that don't behave as
expected
- as usual, lots of driver fixes, improvements, cleanups and new device
addition at the existing drivers.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (831 commits)
[media] cx88: make core less verbose
[media] em28xx: fix oops at em28xx_dvb_bus_ctrl()
[media] s5c73m3: fix indentation of the help section in Kconfig
[media] cx25821-alsa: get rid of a __must_check warning
[media] cx25821-video: declare cx25821_vidioc_s_std as static
[media] cx25821-video: remove maxw from cx25821_vidioc_try_fmt_vid_cap
[media] r820t: Remove a warning for an unused value
[media] dib0090: Fix a warning at dib0090_set_EFUSE
[media] dib8000: fix a warning
[media] dib8000: Fix sub-channel range
[media] dib8000: store dtv_property_cache in a temp var
[media] dib8000: warning fix: declare internal functions as static
[media] r820t: quiet gcc warning on n_ring
[media] r820t: memory leak in release()
[media] r820t: precendence bug in r820t_xtal_check()
[media] videodev2.h: Remove the unused old V4L1 buffer types
[media] anysee: Grammar s/report the/report to/
[media] anysee: Initialize ret = 0 in anysee_frontend_attach()
[media] media: videobuf2: fix the length check for mmap
[media] em28xx: save isoc endpoint number for DVB only if endpoint has alt settings with xMaxPacketSize != 0
...
* patchwork: (831 commits)
[media] cx88: make core less verbose
[media] em28xx: fix oops at em28xx_dvb_bus_ctrl()
[media] s5c73m3: fix indentation of the help section in Kconfig
[media] cx25821-alsa: get rid of a __must_check warning
[media] cx25821-video: declare cx25821_vidioc_s_std as static
[media] cx25821-video: remove maxw from cx25821_vidioc_try_fmt_vid_cap
[media] r820t: Remove a warning for an unused value
[media] dib0090: Fix a warning at dib0090_set_EFUSE
[media] dib8000: fix a warning
[media] dib8000: Fix sub-channel range
[media] dib8000: store dtv_property_cache in a temp var
[media] dib8000: warning fix: declare internal functions as static
[media] r820t: quiet gcc warning on n_ring
[media] r820t: memory leak in release()
[media] r820t: precendence bug in r820t_xtal_check()
[media] videodev2.h: Remove the unused old V4L1 buffer types
[media] anysee: Grammar s/report the/report to/
[media] anysee: Initialize ret = 0 in anysee_frontend_attach()
[media] media: videobuf2: fix the length check for mmap
[media] em28xx: save isoc endpoint number for DVB only if endpoint has alt settings with xMaxPacketSize != 0
...
Conflicts:
drivers/media/pci/cx25821/cx25821-video.c
drivers/media/platform/Kconfig
Current code does this:
be16_to_cpu(buf[i * 2] << 8 | buf[(i * 2) + 1])
Which is effectively (neglecting the index):
be16_to_cpu(be16_to_cpu(*((u16 *) buf)))
This means the int16 in the buffer is not converted at all.
Daniel Mack confirmed that the driver works on little endian
CPUs, leading to the conclusion that the device-side structure
is actually little endian.
This changes the code to use le16_to_cpu().
Caught by sparse.
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Here's the big char / misc driver update for 3.10-rc1
A number of various driver updates, the majority being new functionality
in the MEI driver subsystem (it's now a subsystem, it started out just a
single driver), extcon updates, memory updates, hyper-v updates, and a
bunch of other small stuff that doesn't fit in any other tree.
All of these have been in linux-next for a while
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlF+mtYACgkQMUfUDdst+ymFXQCfdLsD4Cxz+jkgW+tljh9i70XD
OFkAnRPMMhLS8/kddf02lLMYzYUFdy1U
=zaFJ
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver update from Greg Kroah-Hartman:
"Here's the big char / misc driver update for 3.10-rc1
A number of various driver updates, the majority being new
functionality in the MEI driver subsystem (it's now a subsystem, it
started out just a single driver), extcon updates, memory updates,
hyper-v updates, and a bunch of other small stuff that doesn't fit in
any other tree.
All of these have been in linux-next for a while"
* tag 'char-misc-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (148 commits)
Tools: hv: Fix a checkpatch warning
tools: hv: skip iso9660 mounts in hv_vss_daemon
tools: hv: use FIFREEZE/FITHAW in hv_vss_daemon
tools: hv: use getmntent in hv_vss_daemon
Tools: hv: Fix a checkpatch warning
tools: hv: fix checks for origin of netlink message in hv_vss_daemon
Tools: hv: fix warnings in hv_vss_daemon
misc: mark spear13xx-pcie-gadget as broken
mei: fix krealloc() misuse in in mei_cl_irq_read_msg()
mei: reduce flow control only for completed messages
mei: reseting -> resetting
mei: fix reading large reposnes
mei: revamp mei_irq_read_client_message function
mei: revamp mei_amthif_irq_read_message
mei: revamp hbm state machine
Revert "drivers/scsi: use module_pcmcia_driver() in pcmcia drivers"
Revert "scsi: pcmcia: nsp_cs: remove module init/exit function prototypes"
scsi: pcmcia: nsp_cs: remove module init/exit function prototypes
mei: wd: fix line over 80 characters
misc: tsl2550: Use dev_pm_ops
...
Some Asihpi formats are not supported or invalid, and their mapping to
ALSA format is set to -1.
Before performing the format conversion into ALSA bitwise formats,
add a consistency check for the requested format, as done in
snd_card_asihpi_playback_formats().
Compile tested only.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a function to handle conversion from snd_pcm_format_t
to bitwise with proper typing.
Change such conversions to use this function and silence sparse
warnings.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
for reading compressed data, we need to allow when we are paused, draining or
stopped.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This enables better volume controls than the current model parser.
Also, because the original quirk for X220 was added to fix
docking station support, add the TP410 fixup instead.
Reported-by: Willian Jon McCann <william.jon.mccann@gmail.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent changes in the USB API ("implement new semantics for
URB_ISO_ASAP") made the former meaning of the URB_ISO_ASAP flag the
default, and changed this flag to mean that URBs can be delayed.
This is not the behaviour wanted by any of the audio drivers because
it leads to discontinuous playback with very small period sizes.
Therefore, our URBs need to be submitted without this flag.
Reported-by: Joe Rayhawk <jrayhawk@fairlystable.org>
Cc: <stable@vger.kernel.org> # 3.8 only
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merging in fixes since there's a conflict in the omap4 clock tables caused by
it.
* fixes: (245 commits)
ARM: highbank: fix cache flush ordering for cpu hotplug
ARM: OMAP4: hwmod data: make 'ocp2scp_usb_phy_phy_48m" as the main clock
arm: mvebu: Fix the irq map function in SMP mode
Fix GE0/GE1 init on ix2-200 as GE0 has no PHY
ARM: S3C24XX: Fix interrupt pending register offset of the EINT controller
ARM: S3C24XX: Correct NR_IRQS definition for s3c2440
ARM i.MX6: Fix ldb_di clock selection
ARM: imx: provide twd clock lookup from device tree
ARM: imx35 Bugfix admux clock
ARM: clk-imx35: Bugfix iomux clock
+ Linux 3.9-rc6
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-omap2/cclock44xx_data.c
The Scarlett 2i2 seems to take almost 500 ms to set the sample rate,
even if the clock is currently set to that value. This patch speeds
up prepare of the device, by avoiding setting the clock to something
it already is.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The virt_to_bus/bus_to_virt functions have been deprecated
for as long as I can remember, and they are used in very
few remaining instances, usually in obscure ISA device
drivers. The OSS sound drivers are the only ones that are
still used on the ARM architecture, and only on some of
the earliest StrongARM machines.
The problem for converting the OSS subsystem to use
dma_map_single instead is that the caller of virt_to_bus
does not have a device pointer, since the subsystem has
never been ported to use the common device infrastructure.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ARM cannot handle udelay for more than 2 miliseconds, so we
should use mdelay instead for those.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few more fixes, nothing too major though the DMA changes fix modular
builds.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=CgWu
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: More updates for v3.10
A few more fixes, nothing too major though the DMA changes fix modular
builds.
We've got strange errors in get_ctl_value() in mixer.c during
probing, e.g. on Hercules RMX2 DJ Controller:
ALSA mixer.c:352 cannot get ctl value: req = 0x83, wValue = 0x201, wIndex = 0xa00, type = 4
ALSA mixer.c:352 cannot get ctl value: req = 0x83, wValue = 0x200, wIndex = 0xa00, type = 4
....
It turned out that the culprit is autopm: snd_usb_autoresume() returns
-ENODEV when called during card->probing = 1.
Since the call itself during card->probing = 1 is valid, let's fix the
return value of snd_usb_autoresume() as success.
Reported-and-tested-by: Daniel Schürmann <daschuer@mixxx.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The USB_DT_CS_ENDPOINT class-specific endpoint descriptor is usually
stuffed directly after the standard USB endpoint descriptor, and this is
where the driver currently expects it to be.
There are, however, devices in the wild that have it the other way
around in their descriptor sets, so the USB_DT_CS_ENDPOINT comes
*before* the standard enpoint. Devices known to implement it that way
are "Sennheiser BTD-500" and Plantronics USB headsets.
When the driver can't find the USB_DT_CS_ENDPOINT, it won't be able to
change sample rates, as the bitmask for the validity of this command is
storen in bmAttributes of that descriptor.
Fix this by searching the entire interface instead of just the extra
bytes of the first endpoint, in case the latter fails.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-and-tested-by: Torstein Hegge <hegge@resisty.net>
Reported-and-tested-by: Yves G <alsa-user@vivigatt.com>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [b209c4df: ALSA: emu10k1: cache emu1010 firmware] broke the
firmware loading of the dock, just (mistakenly) ignoring a different
firmware for docks on some models. This patch revives them again.
Bugzilla: https://bugs.archlinux.org/task/34865
Reported-and-tested-by: Tobias Powalowski <tobias.powalowski@googlemail.com>
Cc: <stable@vger.kernel.org> [v3.8+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We get a lot of build warnings from the msp driver like:
In file included from sound/soc/ux500/ux500_msp_dai.h:21:0,
from sound/soc/ux500/mop500.c:25:
sound/soc/ux500/ux500_msp_i2s.h:546:11: warning: 'struct msp_i2s_platform_data' declared inside parameter list [enabled by default]
struct msp_i2s_platform_data *platform_data);
^
sound/soc/ux500/ux500_msp_i2s.h:546:11: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
The easiest solution is to add a declaration of the struct name.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For TDM mode, BCLK-to-LCLK ratio is computed as (tdm_slots) x (word_length).
I2S mode is only subset of TDM mode with specific tdm_slots = 2 channels.
Also bclk_lrclk_ratio can be greater than 255, therefore u16 need to be used.
Signed-off-by: Michal Bachraty <michal.bachraty@streamunlimited.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As pointed of by Vaibhav, commit message: "ASoC: davinci-mcasp: Add support for multichannel playback"
number of active serializers can be hidden into fifo_level variable, which is set in davimci-mcasp.
Signed-off-by: Michal Bachraty <michal.bachraty@streamunlimited.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
dma_request_slave_channel() is a more appropriate API for dmaengine
clients that adopt generic DMA bindings to call. Let's use it instead
of of_dma_request_slave_channel() to save <linux/of_dma.h> include.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The examples in Documentation/devicetree/bindings/dma/dma.txt recommends
the name for dma channel doing both RX and TX to be "rx-tx". This
becomes a common pattern that has been adopted by platforms that
converts to generic DMA bindings. Let's follow this common pattern in
generic-dmaengine-pcm.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
These are being reported as being so noisy at high mic boost levels,
so they are unusable in practice.
Therefore artificially limit the boosts.
BugLink: https://bugs.launchpad.net/bugs/1089795
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the generic dmaengine PCM driver instead of a custom implementation.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This allows us to access the DAI DMA data when we create the PCM. We'll use
this when converting mxs to generic DMA engine PCM driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The MXS SAIF is only half-duplex so set the SNDRV_PCM_INFO_HALF_DUPLEX flag for
the PCM in order to prevent playback and capture from running at the same time.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some platforms which are half-duplex share the same DMA channel between the
playback and capture stream. Add support for this to the generic dmaengine PCM
driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Set the timeout for USB control set messages according to the USB 2
spec, using the macros from include/linux/usb.h.
The get timout becomes 5000 ms even though it is 500 ms in the
spec. This patch is required to run the Hercules RMX2 which needs a
timeout of 1240 ms.
More notes from author:
I still distinguish between set and get but as long both are 5000 ms
GCC will remove it anyway. IMHO this is more easy read and there is no
need to explain why we use a get timeout for set messages.
Signed-off-by: Daniel Schürmann <daschuer@mixxx.org>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Like the previous patch by Dan, we should clear the data to be
returned from certain compress ioctls, namely,
snd_compr_get_codec_caps() and snd_compr_get_params().
This time, we can simply replace kmalloc() with kzalloc().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the ->get_caps() function doesn't clear the buffer then there would
stack information leaked to userspace. For example,
soc_compr_get_caps() can return success without clearing the buffer.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch reworks the writes to use cumulative values thus making the
app_pointer unecessary and removing it.
Only tested as far as build.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Only tested as far as build.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Previously we just hard coded all streams as playback streams, this
patch checks the DAI to see if it is a capture or playback stream. It is
worth noting that at this time only unidirectional streams are
supported.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The buffer passed to the copy callback should not be const because the
copy callback can be used for capture and playback.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The app_pointer is managed locally by the compress core for memory
mapped DSPs but for DSPs that are not memory mapped this would have to
be manually updated from within the DSP driver itself, which is hardly
very idiomatic.
This patch switches to using the cumulative values to calculate the
available buffer space because these are already gracefully passed out
of the DSP driver to the compress core and otherwise should be
functionally equivalent.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is my example conversion of a few existing mmap users. The pcm
mmap case is one of the more straightforward ones.
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The main additional change here is Lars-Peter's DMA work plus the
platform conversions which have been tested - getting this in mainline
will make life easier for development after the merge window. These
factor a large chunk of code out of the drivers for the platforms using
dmaengine, greatly simplifying development.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=MXrq
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: More updates for v3.10
The main additional change here is Lars-Peter's DMA work plus the
platform conversions which have been tested - getting this in mainline
will make life easier for development after the merge window. These
factor a large chunk of code out of the drivers for the platforms using
dmaengine, greatly simplifying development.
Use the generic dmaengine PCM driver instead of a custom implemention. There is
a minor functional change, the ux500 PCM driver did not preallocate the audio
buffer, while the generic dmaengine PCM driver will do this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Unfortunately, none of the UAC standards provides a way to identify DSD
(Direct Stream Digital) formats. Hence, this patch adds a quirks
handler to identify USB interfaces that are capable of handling DSD.
That quirks handler can augment the already parsed formats bit-field,
by any of the new SNDRV_PCM_FMTBIT_DSD_{U8_U16} and setting the dsd_dop
flag in the audio format, if the driver should take care for the DOP
byte stuffing.
The only devices that are known to work with this are the ones with
a 'Playback Designs' vendor id.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is quite some confusion around the bit-ordering in DSD samples,
and no general agreement that defines whether hardware is supposed to
expect the oldest sample in the MSB or the LSB of a byte.
ALSA will hence set the rule that on the software API layer, bytes
always carry the oldest bit in the most significant bit of a byte, and
the driver has to translate that at runtime in order to match the
hardware layout.
This patch adds support for this by adding a boolean flag to the
audio format struct.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In order to provide a compatibility way for pushing DSD
samples through ordinary PCM channels, the "DoP open Standard" was
invented. See http://www.dsd-guide.com for the official document.
The host is required to stuff DSD marker bytes (0x05, 0xfa,
alternating) in the MSB of 24 bit wide samples on the bus, in addition
to the 16 bits of actual DSD sample payload.
To support this, the hardware and software stride logic in the driver
has to be tweaked a bit, as we make the userspace believe we're
operating on 16 bit samples, while we in fact push one more byte per
channel down to the hardware.
The DOP runtime information is stored in struct snd_usb_substream, so
we can keep track of our state across multiple calls to
prepare_playback_urb_dsd_dop().
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For normal PCM transfer, this change has no effect, as the endpoint's
stride is always frame_bits/8. For DSD DOP streams, however, which is
added later, the hardware stride differs from the software stride, and
the endpoint has the correct information in these cases.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds two formats for Direct Stream Digital (DSD), a
pulse-density encoding format which is described here:
https://en.wikipedia.org/wiki/Direct_Stream_Digital
DSD operates on 2.8, 5.6 or 11.2MHz sample rates and as a 1-bit
stream.
The two new types added by this patch describe streams that are capable
of handling DSD samples in DOP format as 8-bit or in 16-bit (or at a x8
or x16 data rate, respectively).
DSD itself specifies samples in *bit*, while DOP and ALSA handle them
as *bytes*. Hence, a factor of 8 or 16 has to be applied for the sample
rare configuration, according to the following table:
configured hardware
176.4KHz 352.8kHz 705.6KHz <---- sample rate
8-bit 2.8MHz 5.6MHz
16-bit 2.8Mhz 5.6MHz 11.2MHz
`-----------------------------'
actual DSD sample rates
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When pin default configs are overridden via patch option, these are
evaluated before fixups are applied. Since some fixups change the
whole codec trees and/or add pins dynamically, this sanity check might
not pass when pins aren't present at the time the function is called.
We may reorder the execution, but an easier fix is simply to disable
this sanity check.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fabio Estevam