This patch fixes another potential buffer overflow while processing
iscsi_node_auth input for configfs attributes in v3.11 for-next
TPG tfc_tpg_auth_cit context.
Reported-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a potential buffer overflow while processing
iscsi_node_auth input for configfs attributes within NodeACL
tfc_tpg_nacl_auth_cit context.
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The SBC-2 specification of READ CAPACITY(10) has PMI and LOGICAL BLOCK
ADDRESS fields in the CDB; in SBC-3 these fields are simply listed as
obsolete. However, SBC-2 also has the language
If the PMI bit is set to zero and the LOGICAL BLOCK ADDRESS field
is not set to zero, the device server shall terminate the command
with CHECK CONDITION status with the sense key set to ILLEGAL
REQUEST and the additional sense code set to INVALID FIELD IN CDB.
and in fact at least the Windows SCSI compliance test checks this
behavior. Since no one following SBC-3 is going to set these fields,
we might as well include the check from SBC-2 and pass this test.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We should use TCM_ADDRESS_OUT_OF_RANGE (-> sense data LOGICAL BLOCK
ADDRESS OUT OF RANGE) for IOs past the end of a device instead of
INVALID FIELD IN CDB.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds tracepoints to the target code for commands being
received and being completed, which is quite useful for debugging
interactions with initiators. For example, one can do something like the
following to watch commands that are completing unsuccessfully:
# echo 'scsi_status!=0' > /sys/kernel/debug/tracing/events/target/target_cmd_complete/filter
# echo 1 > /sys/kernel/debug/tracing/events/target/target_cmd_complete/enable
<run command that fails>
# cat /sys/kernel/debug/tracing/trace
iscsi_trx-0-1902 [003] ...1 990185.810385: target_cmd_complete: iqn.1993-08.org.debian:01:e51ede6aacfd <- LUN 001 status CHECK CONDITION (sense len 18 / 70 00 05 00 00 00 00 0a 00 00 00 00 20 00 00 00 00 00) 0x95 data_length 512 CDB 95 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 (TA:SIMPLE C:00)
(v2: Drop undefined COMPARE_AND_WRITE)
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a bug where RDMA_CM_EVENT_DISCONNECTED may occur
before the connection shutdown has been completed by rx/tx threads,
that causes isert_free_conn() to wait indefinately on ->conn_wait.
This patch allows isert_disconnect_work code to invoke rdma_disconnect
when isert_disconnect_work() process context is started by client
session reset before isert_free_conn() code has been reached.
It also adds isert_conn->conn_mutex protection for ->state within
isert_disconnect_work(), isert_cq_comp_err() and isert_free_conn()
code, along with isert_check_state() for wait_event usage.
(v2: Add explicit iscsit_cause_connection_reinstatement call
during isert_disconnect_work() to force conn reset)
Cc: stable@vger.kernel.org # 3.10+
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds target_get_sess_cmd reference counting for
iscsit_handle_task_mgt_cmd(), and adds a target_put_sess_cmd()
for the failure case.
It also fixes a bug where ISCSI_OP_SCSI_TMFUNC type commands
where leaking iscsi_cmd->i_conn_node and eventually triggering
an OOPs during struct isert_conn shutdown.
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch moves ISCSI_OP_REJECT failures into iscsit_sequence_cmd()
in order to avoid external iscsit_reject_cmd() reject usage for all
PDU types.
It also updates PDU specific handlers for traditional iscsi-target
code to not reset the session after posting a ISCSI_OP_REJECT during
setup.
(v2: Fix CMDSN_LOWER_THAN_EXP for ISCSI_OP_SCSI to call
target_put_sess_cmd() after iscsit_sequence_cmd() failure)
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes iscsit_add_reject() + iscsit_add_reject_from_cmd()
usage to not sleep on iscsi_cmd->reject_comp to address a free-after-use
usage bug in v3.10 with iser-target code.
It saves ->reject_reason for use within iscsit_build_reject() so the
correct value for both transport cases. It also drops the legacy
fail_conn parameter usage throughput iscsi-target code and adds
two iscsit_add_reject_cmd() and iscsit_reject_cmd helper functions,
along with various small cleanups.
(v2: Re-enable target_put_sess_cmd() to be called from
iscsit_add_reject_from_cmd() for rejects invoked after
target_get_sess_cmd() has been called)
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fix-up breakage in iscsit_build_sendtargets_response() from v3.11
changes, and free "payload" before returning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
All REJECT response setup of the rejected payload is now done using
on-demand cmd->buf_ptr allocations.
Go ahead and remove dead iscsi_conn->bad_hdr usage rx_opcode path
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fix up sense_reason_t breakage in core_scsi3_update_and_write_aptpl()
from recent conversion to use local scope memory allocation.
Reported as sparse warnings: (new ones prefixed by >>) by Fengguang:
>> drivers/target/target_core_pr.c:2069:57: sparse: incorrect type in
>> return expression (different base types)
drivers/target/target_core_pr.c:2069:57: expected restricted sense_reason_t
drivers/target/target_core_pr.c:2069:57: got int
>> drivers/target/target_core_pr.c:2179:21: sparse: incorrect type in
>> assignment (different base types)
drivers/target/target_core_pr.c:2179:21: expected restricted sense_reason_t [assigned] [usertype] ret
drivers/target/target_core_pr.c:2179:21: got int
>> drivers/target/target_core_pr.c:2197:13: sparse: incorrect type in
>> assignment (different base types)
drivers/target/target_core_pr.c:2197:13: expected restricted sense_reason_t [assigned] [usertype] ret
drivers/target/target_core_pr.c:2197:13: got int
drivers/target/target_core_pr.c:1245:28: sparse: context imbalance in '__core_scsi3_free_registration' - unexpected unlock
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a auth configfs group context following existing
explict NodeACL and discovery auth within:
/sys/kernel/config/target/iscsi/$TARGETNAME/$TPGT/auth/
This patch allows these attributes to be used for CHAP authentication
an TPG is configured in demo-mode (generate_node_acl=1).
Note this authentication information takes precedence over NodeACL
authentication when struct se_node_acl->dynamic_node_acl is present.
Cc: Dax Kelson <dkelson@gurulabs.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds an optional /auth/ configfs group to TPG context that
can be used by fabrics like iscsi-target for TPG demo-mode
authentication.
Cc: Dax Kelson <dkelson@gurulabs.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes ISCSI_OP_TEXT handling of SendTargets=[iqn.,eui.]
payloads to return explicit discovery information.
It adds checks to iscsit_process_text_cmd() and adds the special single
$TARGETNAME discovery case in iscsit_build_sendtargets_response() code.
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch moves ISCSI_OP_TEXT PDU buffer sanity checks to
iscsit_process_text_cmd() code, so that it can be shared
with iser-target code.
It adds IFC_SENDTARGETS_ALL + iscsi_cmd->text_in_ptr in order
to save text payload for ISCSI_OP_TEXT_RSP, and updates
iscsit_release_cmd() to assigned memory.
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes iscsi_set_connection_parameters() to allow
conn_ops->MaxXmitDataSegmentLength assignement to occur during
in-band iser send-targets discovery, as this value is required
by TEXT response processing code.
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch refactoring existing iscsit_send_text_rsp() in order
to handle iscsi_text_rsp payloads in a transport specific manner.
This includes the addition of iscsit_build_text_rsp() to build
the response payload and initialize ISCSI_OP_TEXT_RSP.
v2: Make iscsit_build_text_rsp() determine extra padding bytes, and
drop legacy padding calculation for traditional iSCSI text
responses within iscsit_send_text_rsp()
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch refactors ISCSI_OP_TEXT handling within iscsi-target in
order to handle iscsi_text payloads in a transport specific manner.
This includes splitting current iscsit_handle_text_cmd() into
iscsit_setup_text_cmd() and iscsit_process_text_cmd() calls, and
makes iscsit_handle_text_cmd be only used internally by traditional
iscsi socket calls.
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch refactors ISCSI_OP_NOOP handling within iscsi-target in
order to handle iscsi_nopout payloads in a transport specific manner.
This includes splitting existing iscsit_handle_nop_out() into
iscsit_setup_nop_out() and iscsit_process_nop_out() calls, and
makes iscsit_handle_nop_out() be only used internally by traditional
iscsi socket calls.
Next update iser-target code to use new callers and add FIXME for
the handling iscsi_nopout payloads. Also fix reject response handling
in iscsit_setup_nop_out() to use proper iscsit_add_reject_from_cmd().
v2: Fix uninitialized iscsit_handle_nop_out() payload_length usage (Fengguang)
v3: Remove left-over dead code in iscsit_setup_nop_out() (DanC)
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Writing 0 when iser was not previously enabled, so succeed but do
nothing so that user-space code doesn't need a try: catch block
when ib_isert logic is not available.
Also, return actual error from add_network_portal using PTR_ERR
during op=enable failure.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now with iscsi-target using modern se_cmd->cmd_kref accounting in
v3.10 code, it's safe to go ahead and drop the legacy release
codepath + se_cmd->check_release bit in transport_release_cmd()
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@kernel.org>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Moussa Ba <moussaba@micron.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In modern iscsi-target code, the setup and I/O submission is done within a
single process context, so there is no need to acquire se_cmd->t_state_lock while
checking SCF_SUPPORTED_SAM_OPCODE for determining when unsolicited data-out
should be dumped.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@kernel.org>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Moussa Ba <moussaba@micron.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch drops the se_cmd->t_state_lock access around SCF_SUPPORTED_SAM_OPCODE
assignment within target_setup_cmd_from_cdb().
Original v4.0 target code required this as fabrics would be checking for
this values in different process contexts for setup and I/O submission.
Given that modern v4.1 target code performs setup and I/O submission
from the same process context, this t_state_lock access is no longer
required.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@kernel.org>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Moussa Ba <moussaba@micron.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch makes target_execute_cmd() set CMD_T_BUSY|CMD_T_SENT while
holding se_cmd->t_state_lock, in order to avoid the extra aquire/release
in __target_execute_cmd().
It also clears these bits in case of a target_handle_task_attr()
failure.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@kernel.org>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Moussa Ba <moussaba@micron.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch removes legacy se_cmd->t_fe_count usage in order to avoid
se_cmd->t_state_lock access within transport_put_cmd() during normal
fast path se_cmd descriptor release.
Also drop the left-over parameter usage within core_tmr_handle_tas_abort()
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@kernel.org>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Moussa Ba <moussaba@micron.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch drops an unnecessary acquire/release of se_cmd->t_state_lock within
transport_lun_remove_cmd() when checking CMD_T_DEV_ACTIVE for invoking
target_remove_from_state_list().
For all fast path completion cases, transport_lun_remove_cmd() is always
called ahead of transport_cmd_check_stop(), and since transport_cmd_check_stop()
is calling target_remove_from_state_list() when remove_from_lists=true,
the t_state_lock usage in transport_lun_remove_cmd() can safely be removed.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@kernel.org>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Moussa Ba <moussaba@micron.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a new transport_cmd_check_stop() parameter for signaling
when TRANSPORT_WRITE_PENDING needs to be set.
This allows transport_generic_new_cmd() to avoid the extra lock acquire/release
of ->t_state_lock in the fast path for DMA_TO_DEVICE operations ahead of
transport_cmd_check_stop() + se_tfo->write_pending().
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@kernel.org>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Moussa Ba <moussaba@micron.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Here is a fun one. Bug seems to have been introduced by commit 140854cb,
almost two years ago. I have no idea why we only started seeing it now,
but we did.
Rough callgraph:
core_tpg_set_initiator_node_queue_depth()
`-> spin_lock_irqsave(&tpg->session_lock, flags);
`-> lio_tpg_shutdown_session()
`-> iscsit_stop_time2retain_timer()
`-> spin_unlock_bh(&se_tpg->session_lock);
`-> spin_lock_bh(&se_tpg->session_lock);
`-> spin_unlock_irqrestore(&tpg->session_lock, flags);
core_tpg_set_initiator_node_queue_depth() used to call spin_lock_bh(),
but 140854cb changed that to spin_lock_irqsave(). However,
lio_tpg_shutdown_session() still claims to be called with spin_lock_bh()
held, as does iscsit_stop_time2retain_timer():
* Called with spin_lock_bh(&struct se_portal_group->session_lock) held
Stale documentation is mostly annoying, but in this case the dropping
the lock with the _bh variant is plain wrong. It is also wrong to drop
locks two functions below the lock-holder, but I will ignore that bit
for now.
After some more locking and unlocking we eventually hit this backtrace:
------------[ cut here ]------------
WARNING: at kernel/softirq.c:159 local_bh_enable_ip+0xe8/0x100()
Pid: 24645, comm: lio_helper.py Tainted: G O 3.6.11+
Call Trace:
[<ffffffff8103e5ff>] warn_slowpath_common+0x7f/0xc0
[<ffffffffa040ae37>] ? iscsit_inc_conn_usage_count+0x37/0x50 [iscsi_target_mod]
[<ffffffff8103e65a>] warn_slowpath_null+0x1a/0x20
[<ffffffff810472f8>] local_bh_enable_ip+0xe8/0x100
[<ffffffff815b8365>] _raw_spin_unlock_bh+0x15/0x20
[<ffffffffa040ae37>] iscsit_inc_conn_usage_count+0x37/0x50 [iscsi_target_mod]
[<ffffffffa041149a>] iscsit_stop_session+0xfa/0x1c0 [iscsi_target_mod]
[<ffffffffa0417fab>] lio_tpg_shutdown_session+0x7b/0x90 [iscsi_target_mod]
[<ffffffffa033ede4>] core_tpg_set_initiator_node_queue_depth+0xe4/0x290 [target_core_mod]
[<ffffffffa0409032>] iscsit_tpg_set_initiator_node_queue_depth+0x12/0x20 [iscsi_target_mod]
[<ffffffffa0415c29>] lio_target_nacl_store_cmdsn_depth+0xa9/0x180 [iscsi_target_mod]
[<ffffffffa0331b49>] target_fabric_nacl_base_attr_store+0x39/0x40 [target_core_mod]
[<ffffffff811b857d>] configfs_write_file+0xbd/0x120
[<ffffffff81148f36>] vfs_write+0xc6/0x180
[<ffffffff81149251>] sys_write+0x51/0x90
[<ffffffff815c0969>] system_call_fastpath+0x16/0x1b
---[ end trace 3747632b9b164652 ]---
As a pure band-aid, this patch drops the _bh.
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Nobody should be expecting to read or write virtual_lun0.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Use bool params when appropriate.
Eliminate unneeded pr_reg_e and type variables.
Just one goto label, so rename to 'out' from 'out_put_pr_reg'.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Don't need goto, we can just do an if/else for sa_res_key behavior. Move
shorter case first. Slightly shorter b/c both cases can share a call to
update_and_write_aptpl() now.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of taking the buffer and length, update_and_write_aptpl() will
allocate the buffer as needed, and then free it. Instead, the function
takes an 'aptpl' boolean parameter.
This enables us to remove memory alloc/frees from struct
t10_pr_registration and other spots.
There is a slight loss of functionality because each callsite doesn't get
its own pr_debug any more, but this info can be cleaned via ftrace if
necessary and I think the shorter code is worth it.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
As mentioned in the comments in update_and_write_aptpl,
write_aptpl_to_file() calls strlen() on the buffer, and the length was
always being passed as zero.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
It's only ever set to PR_APTPL_BUF_LEN, so we don't need a variable.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The __ version is only ever called from the regular version, so just
inline it. It's not too much more complex to handle both spinlocks in the
same function.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Simpler to just set buf in update_and_write_aptpl(), rather than passing
down to ____core_scsi3_update_aptpl_buf().
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
They're in emulate_pro_register, so change UNREGISTER to REGISTER.
The first one seems wrong -- sa_res_key could be 0 there, but it's testing
spec_i_pt.
Remove unneeded parens in 2nd conditional.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We use this function exclusively in debug prints. Instead of returning
0 or 1 if isid is present, just set buf to "" if it isn't there. This
saves callers from having to check the return value.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
core_scsi3_enulate_pro_register took an 'ignore_key' parameter that
really distinguished between REGISTER and REGISTER_AND_IGNORE_EXISTING_KEY
registration types, which was a little confusing. Same situation for
PREEMPT and PREEMPT_AND_ABORT. Use enums to add a little more
descriptiveness to the code.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Go ahead and propigate up the ->cmd_kref put return value from
target_put_sess_cmd() -> transport_release_cmd() -> transport_put_cmd()
-> transport_generic_free_cmd().
This is useful for certain fabrics when determining the active I/O
shutdown case with SCF_ACK_KREF where a final target_put_sess_cmd()
is still required by the caller.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If a key was larger than 64 bytes, as checked by iscsi_check_key(), the
error response packet, generated by iscsi_add_notunderstood_response(),
would still attempt to copy the entire key into the packet, overflowing
the structure on the heap.
Remote preauthentication kernel memory corruption was possible if a
target was configured and listening on the network.
CVE-2013-2850
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug where FILEIO was incorrectly reporting the number
of logical blocks (+ 1) when using non struct block_device export mode.
It changes fd_get_blocks() to follow all other backend ->get_blocks() cases,
and reduces the calculated dev_size by one dev->dev_attrib.block_size
number of bytes, and also fixes initial fd_block_size assignment at
fd_configure_device() time introduced in commit 0fd97ccf4.
Reported-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Reported-by: Badari Pulavarty <pbadari@us.ibm.com>
Tested-by: Badari Pulavarty <pbadari@us.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Switch back to pre commit 1c7b13fe65 list splicing logic for active I/O
shutdown with tcm_qla2xxx + ib_srpt fabrics.
The original commit was done under the incorrect assumption that it's safe to
walk se_sess->sess_cmd_list unprotected in target_wait_for_sess_cmds() after
sess->sess_tearing_down = 1 has been set by target_sess_cmd_list_set_waiting()
during session shutdown.
So instead of adding sess->sess_cmd_lock protection around sess->sess_cmd_list
during target_wait_for_sess_cmds(), switch back to sess->sess_wait_list to
allow wait_for_completion() + TFO->release_cmd() to occur without having to
walk ->sess_cmd_list after the list_splice.
Also add a check to exit if target_sess_cmd_list_set_waiting() has already
been called, and add a WARN_ON to check for any fabric bug where new se_cmds
are added to sess->sess_cmd_list after sess->sess_tearing_down = 1 has already
been set.
Cc: Joern Engel <joern@logfs.org>
Cc: Roland Dreier <roland@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Drop unused transport_wait_for_tasks() check in target_wait_for_sess_cmds
shutdown code, and convert tcm_qla2xxx + ib_srpt fabric drivers.
Cc: Joern Engel <joern@logfs.org>
Cc: Roland Dreier <roland@kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull target fixes from Nicholas Bellinger:
"A handful of fixes + minor changes this time around, along with one
important >= v3.9 regression fix for IBLOCK backends. The highlights
include:
- Use FD_MAX_SECTORS in FILEIO for block_device as
well as files (agrover)
- Fix processing of out-of-order CmdSNs with
iSBD driver (shlomo)
- Close long-standing target_put_sess_cmd() vs.
core_tmr_abort_task() race with the addition of
kref_put_spinlock_irqsave() (joern + greg-kh)
- Fix IBLOCK WCE=1 + DPOFUA=1 backend WRITE
regression in >= v3.9 (nab + bootc)
Note these four patches are CC'ed to stable.
Also, there is still some work left to be done on the active I/O
shutdown path in target_wait_for_sess_cmds() used by tcm_qla2xxx +
ib_isert fabrics that is still being discussed on the list, and will
hopefully be resolved soon."
* 'queue' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: close target_put_sess_cmd() vs. core_tmr_abort_task() race
target: removed unused transport_state flag
target/iblock: Fix WCE=1 + DPOFUA=1 backend WRITE regression
MAINTAINERS: Update target git tree URL
iscsi-target: Fix typos in RDMAEXTENSIONS macro usage
target/rd: Add ramdisk bit for NULLIO operation
iscsi-target: Fix processing of OOO commands
iscsi-target: Make buf param of iscsit_do_crypto_hash_buf() const void *
iscsi-target: Fix NULL pointer dereference in iscsit_send_reject
target: Have dev/enable show if TCM device is configured
target: Use FD_MAX_SECTORS/FD_BLOCKSIZE for blockdevs using fileio
target: Remove unused struct members in se_dev_entry
It is possible for one thread to to take se_sess->sess_cmd_lock in
core_tmr_abort_task() before taking a reference count on
se_cmd->cmd_kref, while another thread in target_put_sess_cmd() drops
se_cmd->cmd_kref before taking se_sess->sess_cmd_lock.
This introduces kref_put_spinlock_irqsave() and uses it in
target_put_sess_cmd() to close the race window.
Signed-off-by: Joern Engel <joern@logfs.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a regression bug introduced in v3.9-rc1 where if the
underlying struct block_device for a IBLOCK backend is configured with
WCE=1 + DPOFUA=1 settings, the rw = WRITE assignment no longer occurs
in iblock_execute_rw(), and rw = 0 is passed to iblock_submit_bios()
in effect causing a READ bio operation to occur.
The offending commit is:
commit d0c8b259f8
Author: Nicholas Bellinger <nab@linux-iscsi.org>
Date: Tue Jan 29 22:10:06 2013 -0800
target/iblock: Use backend REQ_FLUSH hint for WriteCacheEnabled status
Note the WCE=1 + DPOFUA=0, WCE=0 + DPOFUA=1, and WCE=0 + DPOFUA=0 cases
are not affected by this regression bug.
Reported-by: Chris Boot <bootc@bootc.net>
Tested-by: Chris Boot <bootc@bootc.net>
Reported-by: Hannes Reinecke <hare@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a rd_nullio parameter that allows RAMDISK_MCP backends
to function in NULLIO mode, where all se_cmd I/O is immediately completed
in rd_execute_rw() without actually performing the SGL memory copy.
This is useful for performance testing when the ramdisk SGL memory copy
begins to eat lots of cycles during heavy small block workloads, so allow
this bit to be enabled when necessary on a per rd_dev basis.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fix two issues in OOO commands processing done at iscsit_attach_ooo_cmdsn.
Handle command serial numbers wrap around by using iscsi_sna_lt and not regular comparisson.
The routine iterates until it finds an entry whose serial number is greater than the serial number of
the new one, thus the new entry should be inserted before that entry and not after.
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Make the "buf" input param of iscsit_do_crypto_hash_buf() "const void *".
This allows to remove lots of casts in its callers.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fix up a NULL pointer dereference regression in iscsit_send_reject()
introduced by from commit 2ec5a8c11.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
User tools need to know if the device is properly configured, since if
not, some other attributes are invalid.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We can still see the error reported in
https://patchwork.kernel.org/patch/2338981/
when using fileio backed by a block device.
I'm assuming this will get us past that error (from sbc_parse_cdb),
and also assuming it's OK to have our max_sectors be larger than
the block's queue max hw sectors?
Reported-by: Eric Harney <eharney@redhat.com>
Signed-off-by: Andy Grover <agrover@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Some were incremented, but never used anywhere from what I could tell.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
Add a check for an aborted sequence, which has a
NULL sequence pointer, to avoid target crashes.
The most relevant messages from the crash (entered
from video capture) include:
BUG: unable to handle kernel paging request at ffffffffffffffdf
IP: [<ffffffffa02d514c>] fc_seq_send+0x3c/0x150 [libfc]
...
Call Trace:
[<ffffffffa0443de6>] ft_queue_data_in+0x266/0x560 [tcm_fc]
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a new network portal attribute for iser, that lives
under existing iscsi-target configfs layout at:
/sys/kernel/config/target/iscsi/$TARGETNAME/$TPGT/np/$PORTAL/iser
When lio_target_np_store_iser() is enabled, iscsit_tpg_add_network_portal()
will attempt to start an rdma_cma network portal for iser-target, only if
the external ib_isert module transport has been loaded.
When disabled, iscsit_tpg_del_network_portal() will cease iser login service
on the network portal, and release any external ib_isert module reference.
v4 changes:
- Add request_module for ib_isert to lio_target_np_store_iser()
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch refactors TX immediate + response queue handling to use
the new iscsit_transport API callers, and exports the necessary
traditional iscsi PDU response creation functions for iser-target
to utilize.
This includes:
- Add iscsit_build_datain_pdu() for DATAIN PDU init + convert
iscsit_build_datain_pdu()
- Add iscsit_build_logout_rsp() for LOGOUT_RSP PDU init + convert
iscsit_send_logout()
- Add iscsit_build_nopin_rsp() for NOPIN_RSP PDU init + convert
iscsit_send_nopin()
- Add iscsit_build_rsp_pdu() for SCSI_RSP PDU init + convert
iscsit_send_response()
- Add iscsit_build_task_mgt_rsp for TM_RSP PDU init + convert
iscsit_send_task_mgt_rsp()
- Refactor immediate queue state switch into iscsit_immediate_queue()
- Convert handle_immediate_queue() to use iscsit_transport caller
- Refactor response queue state switch into iscsit_response_queue()
- Convert handle_response_queue to use iscsit_transport caller
- Export iscsit_logout_post_handler(), iscsit_increment_maxcmdsn()
and iscsit_tmr_post_handler() for external transport module usage
v5 changes:
- Fix solicited NopIN handling with RDMAExtensions=No (nab)
v3 changes:
- Add iscsit_build_reject for REJECT PDU init + convert
iscsit_send_reject()
v2 changes:
- Add iscsit_queue_rsp() for iscsit_transport->iscsit_queue_data_in()
and iscsit_transport->iscsit_queue_status()
- Update lio_queue_data_in() to use ->iscsit_queue_data_in()
- Update lio_queue_status() to use ->iscsit_queue_status()
- Use mutex_trylock() in iscsit_increment_maxcmdsn()
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch refactors existing traditional iscsi RX side PDU handling
to use iscsit_transport, and exports the necessary logic for external
transport modules.
This includes:
- Refactor iscsit_handle_scsi_cmd() into PDU setup / processing
- Add updated iscsit_handle_scsi_cmd() for tradtional iscsi code
- Add iscsit_set_unsoliticed_dataout() wrapper
- Refactor iscsit_handle_data_out() into PDU check / processing
- Add updated iscsit_handle_data_out() for tradtional iscsi code
- Add iscsit_handle_nop_out() + iscsit_handle_task_mgt_cmd() to
accept pre-allocated struct iscsi_cmd
- Add iscsit_build_r2ts_for_cmd() caller for iscsi_target_transport
to handle ISTATE_SEND_R2T for TX immediate queue
- Refactor main traditional iscsi iscsi_target_rx_thread() PDU switch
into iscsi_target_rx_opcode() using iscsit_allocate_cmd()
- Turn iscsi_target_rx_thread() process context into NOP for
ib_isert side work-queue.
v5 changes:
- Make iscsit_handle_scsi_cmd() static (Fengguang)
- Fix iscsit_handle_scsi_cmd() exception se_cmd leak (nab)
v3 changes:
- Add extra target_put_sess_cmd call in iscsit_add_reject_from_cmd
after completion
v2 changes:
- Disable iscsit_ack_from_expstatsn() usage for RDMAExtentions=Yes
- Disable iscsit_allocate_datain_req() usage for RDMAExtentions=Yes
- Add target_get_sess_cmd() reference counting to
iscsit_setup_scsi_cmd()
- Add TFO->lio_check_stop_free() fabric API caller
- Add export of iscsit_stop_dataout_timer() symbol
- Add iscsit_build_r2ts_for_cmd() for iscsit_transport->iscsit_get_dataout()
- Convert existing usage of iscsit_build_r2ts_for_cmd() to
->iscsit_get_dataout()
- Drop RDMAExtentions=Yes specific check in iscsit_build_r2ts_for_cmd()
- Fix RDMAExtentions -> RDMAExtensions typo (andy)
- Pass correct dump_payload value into iscsit_get_immediate_data()
for iscsit_handle_scsi_cmd()
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts struct iscsi_cmd memory allocation + free to use
->iscsit_alloc_cmd() iscsit_transport API caller, and export
iscsit_allocate_cmd() symbols
Also add iscsi_cmd->release_cmd() to be used seperately from
iscsit_transport for connection/session shutdown.
v2 changes:
- Remove unnecessary checks in iscsit_alloc_cmd (asias)
- Drop iscsit_transport->iscsit_free_cmd() usage
- Drop iscsit_transport->iscsit_unmap_cmd() usage
- Add iscsi_cmd->release_cmd()
- Convert lio_release_cmd() to use iscsi_cmd->release_cmd()
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds RDMAExtensions, InitiatorRecvDataSegmentLength and
TargetRecvDataSegmentLength parameters keys necessary for iser-target
login to occur.
This includes setting the necessary parameters during login path
code within iscsi_login_zero_tsih_s2(), and currently PAGE_SIZE
aligning the target's advertised MRDSL for immediate data and
unsolicited data-out incoming payloads.
v3 changes:
- Add iscsi_post_login_start_timers FIXME for ISER
v2 changes:
- Fix RDMAExtentions -> RDMAExtensions typo (andy)
- Drop unnecessary '== true' conditional checks for type bool
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch performs the initial conversion of existing traditional iscsi
to use iscsit_transport API callers. This includes:
- iscsi-np cleanups for iscsit_transport_type
- Add iscsi-np transport calls w/ ->iscsit_setup_up() and ->iscsit_free_np()
- Convert login thread process context to use ->iscsit_accept_np() for
connections with pre-allocated struct iscsi_conn
- Convert existing socket accept code to iscsit_accept_np()
- Convert login RX/TX callers to use ->iscsit_get_login_rx() and
->iscsit_put_login_tx() to exchange request/response PDUs
- Convert existing socket login RX/TX calls into iscsit_get_login_rx()
and iscsit_put_login_tx()
- Change iscsit_close_connection() to invoke ->iscsit_free_conn() +
iscsit_put_transport() calls.
- Add iscsit_register_transport() + iscsit_unregister_transport() calls
to module init/exit
v4 changes:
- Add missing iscsit_put_transport() call in iscsi_target_setup_login_socket()
failure case
v2 changes:
- Update module init/exit to use register_transport() + unregister_transport()
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Add basic struct iscsit_transport API template to allow iscsi-target for
running with external transport modules using existing iscsi_target_core.h
code.
For all external modules, this calls try_module_get() and module_put()
to obtain + release an external iscsit_transport module reference count.
Also include the iscsi-target symbols necessary in iscsi_transport.h to
allow external transport modules to function.
v3 changes:
- Add iscsit_build_reject export for ISTATE_SEND_REJECT usage
v2 changes:
- Drop unnecessary export of iscsit_get_transport + iscsit_put_transport (roland)
- Add ->iscsit_queue_data_in() to remove extra context switch on RDMA_WRITE
- Add ->iscsit_queue_status() to remove extra context switch on IB_SEND status
- Add ->iscsit_get_dataout() to remove extra context switch on RDMA_READ
- Drop ->iscsit_free_cmd()
- Drop ->iscsit_unmap_cmd()
- Rename iscsit_create_transport() -> iscsit_register_transport() (andy)
- Rename iscsit_destroy_transport() -> iscsit_unregister_transport() (andy)
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
As the comment sais, this allows Solaris initiators to survive
intermittent errors. The comment from someone reading the Solaris
sources seem to imply that multipathing would be broken without this
patch as well.
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: Brian Bunker <brian@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Set is_nonrot attribute according to the block queue if the backend
device is a block device.
Signed-off-by: Asias He <asias@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
iblock_execute_unmap() and fd_execute_unmap share a lot of code.
Add sbc_execute_unmap() helper to remove duplicated code for
iblock_execute_unmap() and fd_execute_unmap().
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Asias He <asias@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Add helper iblock_do_unmap() to remove duplicated code in
iblock_execute_write_same_unmap() and iblock_execute_unmap().
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Asias He <asias@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Add helper fd_do_unmap() to remove duplicated code in
fd_execute_write_same_unmap() and fd_execute_unmap().
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Asias He <asias@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds support for emulation of UNMAP within
fd_execute_unmap() backend code.
If the FILEIO backend is normal file, the emulation uses fallocate to
punch hole to reclaim the free space used by the file. If the FILEIO
backend is block device, the emulation uses blkdev_issue_discard().
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Asias He <asias@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds support for emulation of WRITE_SAME w/ UNMAP=1 within
fd_execute_write_same_unmap() backend code.
If the FILEIO backend is normal file, the emulation uses fallocate to
punch hole to reclaim the free space used by the file. If the FILEIO
backend is block device, the emulation uses blkdev_issue_discard().
Tested with 512, 1k, 2k, and 4k block_sizes.
Changes in v2:
- Set the various dev->dev_attrib.*unmap* values (nab)
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Asias He <asias@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The callback function of call_rcu() just calls a kfree(), so we
can use kfree_rcu() instead of call_rcu() + callback function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fix bit-clearing in login_rsp->flags for case 0.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The result from get_random_bytes should already be random, so further
manipulation and mixing should not be needed.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug where a handful of informational / control CDBs
that should be allowed during ALUA access state Standby/Offline/Transition
where incorrectly returning CHECK_CONDITION + ASCQ_04H_ALUA_TG_PT_*.
This includes INQUIRY + REPORT_LUNS, which would end up preventing LUN
registration when LUN scanning occured during these ALUA access states.
Cc: Hannes Reinecke <hare@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a regression introduced in v3.8-rc1 code where a failed
target_check_reservation() check in target_setup_cmd_from_cdb() was causing
an incorrect SAM_STAT_GOOD status to be returned during a WRITE operation
performed by an unregistered / unreserved iscsi initiator port.
This regression is only effecting iscsi-target due to a special case check
for TCM_RESERVATION_CONFLICT within iscsi_target_erl1.c:iscsit_execute_cmd(),
and was still correctly disallowing WRITE commands from backend submission
for unregistered / unreserved initiator ports, while returning the incorrect
SAM_STAT_GOOD status due to the missing SAM_STAT_RESERVATION_CONFLICT
assignment.
This regression was first introduced with:
commit de103c93af
Author: Christoph Hellwig <hch@lst.de>
Date: Tue Nov 6 12:24:09 2012 -0800
target: pass sense_reason as a return value
Go ahead and re-add the missing SAM_STAT_RESERVATION_CONFLICT assignment
during a target_check_reservation() failure, so that iscsi-target code
sends the correct SCSI status.
All other fabrics using target_submit_cmd_*() with a RESERVATION_CONFLICT
call to transport_generic_request_failure() are not effected by this bug.
Reported-by: Jeff Leung <jleung@curriegrad2004.ca>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We can only have one page of data in each sg element, so we can not
cross a page boundary. Fail this case.
The 'while (len > 0 && data_len > 0) {}' loop is not necessary. The loop
can only be executed once.
Signed-off-by: Asias He <asias@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch bumps the default FILEIO backend FD_MAX_SECTORS value from
1024 -> 2048 in order to allow block_size=512 to handle 1M sized I/Os.
The current default rejects I/Os larger than 512K in sbc_parse_cdb():
[12015.915146] SCSI OP 2ah with too big sectors 1347 exceeds backend
hw_max_sectors: 1024
[12015.977744] SCSI OP 2ah with too big sectors 2048 exceeds backend
hw_max_sectors: 1024
This issue is present in >= v3.5 based kernels, introduced after the
removal of se_task logic.
Reported-by: Viljami Ilola <azmulx@netikka.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
'se_tpg->tpg_lun_list' is malloced in core_tpg_register() and should be freed
before leaving from the error handling cases, otherwise it will cause memory
leak.
'se_tpg' is malloced out of this function, and will be freed if we return error, so
remove free for 'se_tpg'.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
See https://bugzilla.redhat.com/show_bug.cgi?id=916290
Used a temp var since we take its address in sg_init_one.
Signed-off-by: Andy Grover <agrover@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Windows does not expect SYNCHRONIZE_CACHE to be not supported,
and will generate a BSOD upon shutdown when using rd_mcp backend.
So better use a noop here.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target patches from Nicholas Bellinger:
"Here are the remaining target-pending patches for v3.9-rc1.
The most important one here is the immediate queue starvation
regression fix for iscsi-target, which addresses a bug that's
effecting v3.5+ kernels under heavy sustained READ only workloads.
Thanks alot to Benjamin Estrabaud for helping to track this down!
Also included is a pSCSI exception bugfix from Asias, along with a
handful of other minor changes. Both bugfixes are CC'ed to stable."
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target/pscsi: Rename sg_num to nr_vecs in pscsi_get_bio()
target/pscsi: Fix page increment
target/pscsi: Drop unnecessary NULL assignment to bio->bi_next
target: Add __exit annotation for module_exit functions
iscsi-target: Fix immediate queue starvation regression with DATAIN
It is actually a vector not a sg, so nr_vecs is better than sg_num.
Signed-off-by: Asias He <asias@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The page++ is wrong. It makes bio_add_pc_page() pointing to a wrong page
address if the 'while (len > 0 && data_len > 0) { ... }' loop is
executed more than one once.
Signed-off-by: Asias He <asias@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Inclues sbp_exit, fileio_module_exit, iblock_module_exit and
pscsi_module_exit.
Note: rd_module_exit() can not be annotated by __exit, becasue it is
called by target_core_init_configfs() which is annotated by __init.
Signed-off-by: Asias He <asias@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
I'm not sure why, but the hlist for each entry iterators were conceived
list_for_each_entry(pos, head, member)
The hlist ones were greedy and wanted an extra parameter:
hlist_for_each_entry(tpos, pos, head, member)
Why did they need an extra pos parameter? I'm not quite sure. Not only
they don't really need it, it also prevents the iterator from looking
exactly like the list iterator, which is unfortunate.
Besides the semantic patch, there was some manual work required:
- Fix up the actual hlist iterators in linux/list.h
- Fix up the declaration of other iterators based on the hlist ones.
- A very small amount of places were using the 'node' parameter, this
was modified to use 'obj->member' instead.
- Coccinelle didn't handle the hlist_for_each_entry_safe iterator
properly, so those had to be fixed up manually.
The semantic patch which is mostly the work of Peter Senna Tschudin is here:
@@
iterator name hlist_for_each_entry, hlist_for_each_entry_continue, hlist_for_each_entry_from, hlist_for_each_entry_rcu, hlist_for_each_entry_rcu_bh, hlist_for_each_entry_continue_rcu_bh, for_each_busy_worker, ax25_uid_for_each, ax25_for_each, inet_bind_bucket_for_each, sctp_for_each_hentry, sk_for_each, sk_for_each_rcu, sk_for_each_from, sk_for_each_safe, sk_for_each_bound, hlist_for_each_entry_safe, hlist_for_each_entry_continue_rcu, nr_neigh_for_each, nr_neigh_for_each_safe, nr_node_for_each, nr_node_for_each_safe, for_each_gfn_indirect_valid_sp, for_each_gfn_sp, for_each_host;
type T;
expression a,c,d,e;
identifier b;
statement S;
@@
-T b;
<+... when != b
(
hlist_for_each_entry(a,
- b,
c, d) S
|
hlist_for_each_entry_continue(a,
- b,
c) S
|
hlist_for_each_entry_from(a,
- b,
c) S
|
hlist_for_each_entry_rcu(a,
- b,
c, d) S
|
hlist_for_each_entry_rcu_bh(a,
- b,
c, d) S
|
hlist_for_each_entry_continue_rcu_bh(a,
- b,
c) S
|
for_each_busy_worker(a, c,
- b,
d) S
|
ax25_uid_for_each(a,
- b,
c) S
|
ax25_for_each(a,
- b,
c) S
|
inet_bind_bucket_for_each(a,
- b,
c) S
|
sctp_for_each_hentry(a,
- b,
c) S
|
sk_for_each(a,
- b,
c) S
|
sk_for_each_rcu(a,
- b,
c) S
|
sk_for_each_from
-(a, b)
+(a)
S
+ sk_for_each_from(a) S
|
sk_for_each_safe(a,
- b,
c, d) S
|
sk_for_each_bound(a,
- b,
c) S
|
hlist_for_each_entry_safe(a,
- b,
c, d, e) S
|
hlist_for_each_entry_continue_rcu(a,
- b,
c) S
|
nr_neigh_for_each(a,
- b,
c) S
|
nr_neigh_for_each_safe(a,
- b,
c, d) S
|
nr_node_for_each(a,
- b,
c) S
|
nr_node_for_each_safe(a,
- b,
c, d) S
|
- for_each_gfn_sp(a, c, d, b) S
+ for_each_gfn_sp(a, c, d) S
|
- for_each_gfn_indirect_valid_sp(a, c, d, b) S
+ for_each_gfn_indirect_valid_sp(a, c, d) S
|
for_each_host(a,
- b,
c) S
|
for_each_host_safe(a,
- b,
c, d) S
|
for_each_mesh_entry(a,
- b,
c, d) S
)
...+>
[akpm@linux-foundation.org: drop bogus change from net/ipv4/raw.c]
[akpm@linux-foundation.org: drop bogus hunk from net/ipv6/raw.c]
[akpm@linux-foundation.org: checkpatch fixes]
[akpm@linux-foundation.org: fix warnings]
[akpm@linux-foudnation.org: redo intrusive kvm changes]
Tested-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert to the much saner new idr interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Nicholas A. Bellinger <nab@linux-iscsi.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch addresses a v3.5+ regression in iscsi-target where TX thread
process context -> handle_response_queue() execution is allowed to run
unbounded while servicing constant outgoing flow of ISTATE_SEND_DATAIN
response state.
This ends up preventing memory release of StatSN acknowledged commands
in a timely manner when under heavy large block streaming DATAIN
workloads.
The regression bug was initially introduced with:
commit 6f3c0e69a9
Author: Andy Grover <agrover@redhat.com>
Date: Tue Apr 3 15:51:09 2012 -0700
target/iscsi: Refactor target_tx_thread immediate+response queue loops
Go ahead and follow original iscsi_target_tx_thread() logic and check
to break for immediate queue processing after each DataIN Sequence and/or
Response PDU has been sent.
Reported-by: Benjamin ESTRABAUD <be@mpstor.com>
Cc: Andy Grover <agrover@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull vfs pile (part one) from Al Viro:
"Assorted stuff - cleaning namei.c up a bit, fixing ->d_name/->d_parent
locking violations, etc.
The most visible changes here are death of FS_REVAL_DOT (replaced with
"has ->d_weak_revalidate()") and a new helper getting from struct file
to inode. Some bits of preparation to xattr method interface changes.
Misc patches by various people sent this cycle *and* ocfs2 fixes from
several cycles ago that should've been upstream right then.
PS: the next vfs pile will be xattr stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
saner proc_get_inode() calling conventions
proc: avoid extra pde_put() in proc_fill_super()
fs: change return values from -EACCES to -EPERM
fs/exec.c: make bprm_mm_init() static
ocfs2/dlm: use GFP_ATOMIC inside a spin_lock
ocfs2: fix possible use-after-free with AIO
ocfs2: Fix oops in ocfs2_fast_symlink_readpage() code path
get_empty_filp()/alloc_file() leave both ->f_pos and ->f_version zero
target: writev() on single-element vector is pointless
export kernel_write(), convert open-coded instances
fs: encode_fh: return FILEID_INVALID if invalid fid_type
kill f_vfsmnt
vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op
nfsd: handle vfs_getattr errors in acl protocol
switch vfs_getattr() to struct path
default SET_PERSONALITY() in linux/elf.h
ceph: prepopulate inodes only when request is aborted
d_hash_and_lookup(): export, switch open-coded instances
9p: switch v9fs_set_create_acl() to inode+fid, do it before d_instantiate()
9p: split dropping the acls from v9fs_set_create_acl()
...
Pull scsi target updates from Nicholas Bellinger:
"The highlights in this series include:
- Improve sg_table lookup scalability in RAMDISK_MCP (martin)
- Add device attribute to expose config name for INQUIRY model (tregaron)
- Convert tcm_vhost to use lock-less list for cmd completion (asias)
- Add tcm_vhost support for multiple target's per endpoint (asias)
- Add tcm_vhost support for multiple queues per vhost (asias)
- Add missing mapped_lun bounds checking during make_mappedlun setup
in generic fabric configfs code (jan engelhardt + nab)
- Enforce individual iscsi-target network portal export once per
TargetName endpoint (grover + nab)
- Add WRITE_SAME w/ UNMAP=0 emulation to FILEIO backend (nab)
Things have been mostly quiet this round, with majority of the work
being done on the iser-target WIP driver + associated iscsi-target
refactoring patches currently in flight for v3.10 code.
At this point there is one patch series left outstanding from Asias to
add support for UNMAP + WRITE_SAME w/ UNMAP=1 to FILEIO awaiting
feedback from hch & Co, that will likely be included in a post
v3.9-rc1 PULL request if there are no objections.
Also, there is a regression bug recently reported off-list that seems
to be effecting v3.5 and v3.6 kernels with MSFT iSCSI initiators that
is still being tracked down. No word if this effects >= v3.7 just
yet, but if so there will likely another PULL request coming your
way.."
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (26 commits)
target: Rename spc_get_write_same_sectors -> sbc_get_write_same_sectors
target/file: Add WRITE_SAME w/ UNMAP=0 emulation support
iscsi-target: Enforce individual network portal export once per TargetName
iscsi-target: Refactor iscsit_get_np sockaddr matching into iscsit_check_np_match
target: Add missing mapped_lun bounds checking during make_mappedlun setup
target: Fix lookup of dynamic NodeACLs during cached demo-mode operation
target: Fix parameter list length checking in MODE SELECT
target: Fix error checking for UNMAP commands
target: Fix sense data for out-of-bounds IO operations
target_core_rd: break out unterminated loop during copy
tcm_vhost: Multi-queue support
tcm_vhost: Multi-target support
target: Add device attribute to expose config_item_name for INQUIRY model
target: don't truncate the fail intr address
target: don't always say "ipv6" as address type
target/iblock: Use backend REQ_FLUSH hint for WriteCacheEnabled status
iscsi-target: make some temporary buffers larger
tcm_vhost: Optimize gup in vhost_scsi_map_to_sgl
tcm_vhost: Use iov_num_pages to calculate sgl_count
tcm_vhost: Introduce iov_num_pages
...
... in other news:
filp_open() can't return a struct file with NULL dentry
filp_open() can't return a struct file negative dentry
filp_close() of something that never had been in any descriptor
tables is pointless - fput() is all you need
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Trivial, but WRITE SAME is an SBC command so it seems strange for a
related function (defined in target_core_sbc.c) to be in the spc_
namespace.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Nicholas Bellinger