Add new driver to use tethering with an iPhone device. After initial submission,
apply fixes to fit the new driver into the kernel standards.
There are still a couple of minor (almost cosmetic-level) issues, but the driver
is fully functional right now.
Signed-off-by: L. Alberto Giménez <agimenez@sysvalve.es>
Signed-off-by: Diego Giagio <diego@giagio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the existing pppol2tp driver from drivers/net into a
new net/l2tp directory, which is where the upcoming L2TPv3 code will
live. The existing CONFIG_PPPOL2TP config option is left in its
current place to avoid "make oldconfig" issues when an existing
pppol2tp user takes this change. (This is the same approach used for
the pppoatm driver, which moved to net/atm.)
There are no code changes. The existing drivers/net/pppol2tp.c is
simply moved to net/l2tp.
Signed-off-by: James Chapman <jchapman@katalix.com>
Reviewed-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add CAIF Serial driver. This driver is implemented as a line discipline.
caif_serial uses the following module parameters:
ser_use_stx - specifies if STart of frame eXtension is in use.
ser_loop - sets the interface in loopback mode.
Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds device driver for Aeroflex Gaisler 10/100 and 10/100/1G Ethernet
MAC IP cores.
Signed-off-by: Kristoffer Glembo <kristoffer@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Micrel KSZ884X network driver for KSZ8841/KSZ8842 PCI Ethernet chips.
Signed-off-by: Tristram Ha <Tristram.Ha@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to use macvlan with qemu and other tools that require
a tap file descriptor, the macvtap driver adds a small backend
with a character device with the same interface as the tun
driver, with a minimum set of features.
Macvtap interfaces are created in the same way as macvlan
interfaces using ip link, but the netif is just used as a
handle for configuration and accounting, while the data
goes through the chardev. Each macvtap interface has its
own character device, simplifying permission management
significantly over the generic tun/tap driver.
Cc: Patrick McHardy <kaber@trash.net>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: David S. Miller" <davem@davemloft.net>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Or Gerlitz <ogerlitz@voltaire.com>
Cc: netdev@vger.kernel.org
Cc: bridge@lists.linux-foundation.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Separate Ethernet driver for Qlogic CNA devices
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modifications for the Kconfig and network device Makefile to add the ixgbevf
driver module to the kernel plus basic driver documentation.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Octeon MGMT Ethernet ports are present in some members of the
Octeon SOC family (cn52XX and cn56XX have them).
The mdio bus connected to the MGMT PHYs is shared with the main
octeon-ethernet driver, we force it to be loaded first by calling
octeon_mdiobus_force_mod_depencency. The platform devices for the
MGMT Ethernet ports are added in
arch/mips/cavium-octeon/octeon-platform.c, and the register
definitions for the ports live in arch/mips/include/asm/octeon/ along
with their ilk.
Although it currently is the only driver in drivers/net/octeon, the
directory was created looking forward to the day that octeon-ethernet
will move there from its current home in drivers/staging.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ethernet NIC driver for VMware's vmxnet3
From: Shreyas Bhatewara <sbhatewara@vmware.com>
This patch adds driver support for VMware's virtual Ethernet NIC: vmxnet3
Guests running on VMware hypervisors supporting vmxnet3 device will thus have
access to improved network functionalities and performance.
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: Ronghua Zhang <ronghua@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need PHY drivers to initialize in a static kernel before
the MAC drivers that use them. So link them in first.
Based upon a report by Felix Radensky.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the first registration of ks8851 network driver with
MLL(address/data multiplexed) interface.
Signed-off-by : David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for the Xilinx Ethernet Lite device. The
soft logic core from Xilinx is typically used on Virtex and Spartan
designs attached to either a PowerPC or a Microblaze processor.
Signed-off-by: Sadanand M <sadanan@xilinx.com>
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network driver for the SPI version of the Micrel KS8851
network chip.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The s6000 on-chip MAC supports 10/100/1000Mbit and is connected to an
external PHY via MII or RGMII interface.
[jw@emlix.com: don't use device->bus_id directly]
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Daniel Glockner <dg@emlix.com>
Acked-by: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Johannes Weiner <jw@emlix.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Zankel <chris@zankel.net>
Conflicts:
drivers/message/fusion/mptsas.c
fixed up conflict between req->data_len accessors and mptsas driver updates.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The CNIC driver controls BNX2 hardware rings and resources used by
iSCSI. Most hardware resources for iSCSI are separate from those
used for ethernet networking.
iSCSI uses a separate MAC address and IP address. The CNIC driver
creates a UIO interface to handle the non-offloaded packets such as
ARP, etc in userspace.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This is a driver for the Micrel KS8842 ethernet switch.
The supplied code is for driving the KS8842 through the Timberdale FPGA
on the Russellville board, a development board for Intel Atom CPU
in the automotive area.
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changeset ca17584bf2 ("mac8390: update
to net_device_ops") broke mac8390 by adding 8390.o to the link. That
meant that lib8390.c was included twice, once in mac8390.c and once in
8390.c, subject to different macros. This patch reverts that by
avoiding the wrappers in 8390.c. They seem to be of no value since
COMPAT_NET_DEV_OPS is going away soon.
Tested with a Kinetics EtherPort card.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for TI DaVinci EMAC driver.
TI DaVinci Ethernet Media Access Controller module is based upon
TI CPPI 3.0 DMA engine and supports 10/100 Mbps on all and Gigabit modes on
some TI devices. It supports MII/RMII and has up to 8Kbytes of internal
descriptor memory. This driver has been working on several TI devices including
DM644x, DM646x and DA830 platforms. The specs of this device are available at:
http://www.ti.com/litv/pdf/sprue24a
Signed-off-by: Anant Gole <anantgole@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These roughly mirror many of the MII library functions and are based
on code from the sfc driver.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet
device. The ll_temac ipcore is typically used on Xilinx Virtex and
Spartan designs attached to either a PowerPC 4xx or Microblaze
processor.
At the present moment, this driver only works with Virtex5 PowerPC
designs because it assumes DCR is used to access the DMA registers.
However, the low level access to DMA registers is abstracted and
it should be easy to adapt for the other implementations.
I'm posting this driver now as an RFC. There are still some things that
need to be tightened up, but it does appear to be stable.
Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr.
Tested on Xilinx ML507 eval board with Base System Builder generated
FPGA design.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds an igbvf driver to handle virtual functions provided by the
igb driver when SR-IOV has been enabled. A virtual function is a
lightweight pci-e function that supports a single queue and shares
resources with the 82576 physical function contained within the igb
driver.
To spawn virtual functions from the igb driver all that is needed is to
enable CONFIG_PCI_IOV and have an 82576 Ethernet adapter on a system that
supports SR-IOV in the BIOS. The virtual functions will appear after the
interface is loaded.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Kconfig and Makefile related changes for vxge driver.
- No changes in current submission.
- Changes from previous submission -
- Incorporated the following review comments as per Bill Flink:
- Add dependancy on INET along with PCI
- Remove dependancy on INET_LRO and add GRO support.
- Made this patch as last patch as per Ben Hutchings comments.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a platform device driver that supports the OpenCores 10/100
Mbps Ethernet MAC.
The driver expects three resources: one IORESOURCE_MEM resource defines the
memory region for the core's memory-mapped registers while a second
IORESOURCE_MEM resource defines the network packet buffer space. The third
resource, of type IORESOURCE_IRQ, associates an interrupt with the driver.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver for Dave DNET ethernet controller found on Dave/DENX QongEVB-LITE
FPGA. Heavily based on Dave sources, I've just adopted it to current
kernel version and done some code cleanup.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO bus drivers for the UCC and gianfar ethernet controllers are
essentially the same. There's no reason to duplicate that much code.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Integrate the i2400m driver into the kernel's build and Kconfig.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a driver for the LAN9240 PCI ethernet adapter.
Changes since initial submission:
- debug msg_level has been changed to use standard definitions
- convert to use net_device_ops
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another device using 8390 library that needs converting.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another device using 8390 library that needs converting.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another device using 8390 library that needs converting.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another related 8390 driver. Since this is for nubus, not sure if
anyone still has the hardware?
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix hp-plus driver link errors.
Builds as loadable module and kernel image driver.
All drivers that use 8390.o or 8390p.o that will build on
i386 with MCA/PCI/EISA/ISA were built successfully both
=m and =y.
drivers/built-in.o: In function `hpp_open':
hp-plus.c:(.text+0xac06c): undefined reference to `eip_interrupt'
hp-plus.c:(.text+0xac0d7): undefined reference to `eip_open'
drivers/built-in.o: In function `hpp_close':
hp-plus.c:(.text+0xac1bb): undefined reference to `eip_close'
drivers/built-in.o: In function `hpp_probe1':
hp-plus.c:(.init.text+0xa98a): undefined reference to `NS8390p_init'
drivers/built-in.o: In function `hp_plus_probe':
(.init.text+0xa9fe): undefined reference to `__alloc_eip_netdev'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attached is a driver for SMSC's LAN911x and LAN921x families of embedded
ethernet controllers.
There is an existing smc911x driver in the tree; this is intended to
replace it. Dustin McIntire (the author of the smc911x driver) has
expressed his support for switching to this driver.
This driver contains workarounds for all known hardware issues, and has
been tested on all flavours of the chip on multiple architectures.
This driver now uses phylib, so this patch also adds support for the
device's internal phy
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Bahadir Balban <Bahadir.Balban@arm.com>
Signed-off-by: Dustin Mcintire <dustin@sensoria.com>
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Driver for Atheros L2 10/100 network device. Includes necessary
changes for Kconfig, Makefile, and pci_ids.h.
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix hp-plus Makefile object file:
drivers/built-in.o: In function `hpp_open':
hp-plus.c:(.text+0xaf445): undefined reference to `ei_interrupt'
hp-plus.c:(.text+0xaf4ac): undefined reference to `ei_open'
drivers/built-in.o: In function `hpp_close':
hp-plus.c:(.text+0xaf59d): undefined reference to `ei_close'
drivers/built-in.o: In function `hpp_probe1':
hp-plus.c:(.init.text+0x7314): undefined reference to `ei_poll'
drivers/built-in.o: In function `hp_plus_probe':
(.init.text+0x7407): undefined reference to `__alloc_ei_netdev'
make[1]: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Full patch for the Atheros L1E Gigabit Ethernet driver.
Supportring AR8121, AR8113 and AR8114
Signed-off-by: Jie Yang <jie.yang @atheros.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The only user of the board, the extremly dated and rare MIPS Atlas board,
has been removed, so this driver can go, too.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Only a few ISA controllers need the pausing version of the 8390 core
while PCMCIA, later ISA and PCI do not. More importantly the ISA delays
can break non ISA boxes so we must use a different build of 8390.c for
the two sets of controllers.
No changes since last time as all the points of concerns raised proved to
be invalid
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
New Link code:
Moving all the link related code (including the calculations, the
initialization of the MAC and PHY and the external PHY's code) into
a separated file. The changes from the code that used to be part of
bnx2x.c (now called bnx2x_main.c) are:
- Using separate structures for link inputs and link outputs to clearly
identify what was configured and what is the outcome
- Adding code to read external PHY FW version and print it as part of
ethtool -i
- Adding code to upgrade external PHY FW from ethtool -E with special
magic number - Changing the link down indication to ERR level
- Adding a lock on all PHY access to prevent an interrupt and
setting changes to overlap
- Adding support for emulation and FPGA (small chunk of code that really
helps in the lab) - Adding support for 1G on BCM8706 PHY
- Adding clear debug print incase of fan failure (the PHY type is now
"failure")
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is the rename of bnx2x.c to bnx2x_main.c.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The arch/ppc sub-tree has been removed in the powerpc git tree. The old
ibm_emac driver is no longer used by anything as a result of this. This
removes it, leaving the ibm_newemac driver as the proper driver to use for
PowerPC boards with the EMAC hardware.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This driver is for a number of different Option devices. Originally
written by Option and Andrew Bird, but cleaned up massivly for
acceptance into mainline by me and others.
Many thanks to the following for their help in cleaning up the driver by
providing feedback and patches to it:
- Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
- Oliver Neukum <oliver@neukum.org>
- Alan Cox <alan@lxorguk.ukuu.org.uk>
- Javier Marcet <javier@krausbeck.org>
Cc: Andrew Bird <ajb@spheresystems.co.uk>
Cc: Javier Marcet <javier@krausbeck.org>
Cc: Filip Aben <f.aben@option.com>
Cc: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Cc: Oliver Neukum <oliver@neukum.org>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add support for Renesas SuperH Ethernet controller. This driver supports
SH7710 and SH7712.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This driver has been superseded by fs_enet and is no longer in use.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (53 commits)
tcp: Overflow bug in Vegas
[IPv4] UFO: prevent generation of chained skb destined to UFO device
iwlwifi: move the selects to the tristate drivers
ipv4: annotate a few functions __init in ipconfig.c
atm: ambassador: vcc_sf semaphore to mutex
MAINTAINERS: The socketcan-core list is subscribers-only.
netfilter: nf_conntrack: padding breaks conntrack hash on ARM
ipv4: Update MTU to all related cache entries in ip_rt_frag_needed()
sch_sfq: use del_timer_sync() in sfq_destroy()
net: Add compat support for getsockopt (MCAST_MSFILTER)
net: Several cleanups for the setsockopt compat support.
ipvs: fix oops in backup for fwmark conn templates
bridge: kernel panic when unloading bridge module
bridge: fix error handling in br_add_if()
netfilter: {nfnetlink,ip,ip6}_queue: fix skb_over_panic when enlarging packets
netfilter: x_tables: fix net namespace leak when reading /proc/net/xxx_tables_names
netfilter: xt_TCPOPTSTRIP: signed tcphoff for ipv6_skip_exthdr() retval
tcp: Limit cwnd growth when deferring for GSO
tcp: Allow send-limited cwnd to grow up to max_burst when gso disabled
[netdrvr] gianfar: Determine TBIPA value dynamically
...
The driver supports the 10Xpress PHY and XFP modules on our reference
designs SFE4001 and SFE4002 and the SMC models SMC10GPCIe-XFP and
SMC10GPCIe-10BT.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (202 commits)
[POWERPC] Fix compile breakage for 64-bit UP configs
[POWERPC] Define copy_siginfo_from_user32
[POWERPC] Add compat handler for PTRACE_GETSIGINFO
[POWERPC] i2c: Fix build breakage introduced by OF helpers
[POWERPC] Optimize fls64() on 64-bit processors
[POWERPC] irqtrace support for 64-bit powerpc
[POWERPC] Stacktrace support for lockdep
[POWERPC] Move stackframe definitions to common header
[POWERPC] Fix device-tree locking vs. interrupts
[POWERPC] Make pci_bus_to_host()'s struct pci_bus * argument const
[POWERPC] Remove unused __max_memory variable
[POWERPC] Simplify xics direct/lpar irq_host setup
[POWERPC] Use pseries_setup_i8259_cascade() in pseries_mpic_init_IRQ()
[POWERPC] Turn xics_setup_8259_cascade() into a generic pseries_setup_i8259_cascade()
[POWERPC] Move xics_setup_8259_cascade() into platforms/pseries/setup.c
[POWERPC] Use asm-generic/bitops/find.h in bitops.h
[POWERPC] 83xx: mpc8315 - fix USB UTMI Host setup
[POWERPC] 85xx: Fix the size of qe muram for MPC8568E
[POWERPC] 86xx: mpc86xx_hpcn - Temporarily accept old dts node identifier.
[POWERPC] 86xx: mark functions static, other minor cleanups
...
This patch adds support for the IDT rc32434 Ethernet MAC
we can find in the IDT boards and the Mikrotik RB500.
Driver references some code from the linux-mips RB500
support.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Philip Rischel <rischelp@idt.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In preparation for a future Atheros L2 NIC driver (called atl2), relocate
the atl1 driver into a new /drivers/net/atlx directory that will ultimately
be shared with the future atl2 driver.
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
All the hardware supported by this driver is now supported
by the skge driver. The last remaining issue was support for ancient
dual port SysKonnect fiber boards, and the skge driver now does these
correctly (p.s. sk98lin was always broken on these old dual port
boards anyway).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Acked-by: Dan Williams <dcbw@redhat.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We are pleased to announce a new Gigabit Ethernet product and its
driver to the linux community. This product is the Intel(R) 82575
Gigabit Ethernet adapter family. Physical adapters will be available
to the public soon. These adapters come in 2- and 4-port versions
(copper PHY) currently. Other variants will be available later.
The 82575 chipset supports significantly different features that
warrant a new driver. The descriptor format is (just like the
ixgbe driver) different. The device can use multiple MSI-X vectors
and multiple queues for both send and receive. This allows us to
optimize some of the driver code specifically as well compared to
the e1000-supported devices.
This version of the igb driver no lnger uses fake netdevices and
incorporates napi_struct members for each ring to do the multi-
queue polling. multi-queue is enabled by default and the driver
supports NAPI mode only.
All the namespace collisions should be gone in this version too. The
register macro's have been condensed to improve readability.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the RDC R6040 MAC we can find in the RDC
R-321x System-on-chips.
Signed-off-by: Sten Wang <sten.wang@rdc.com.tw>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
This patch contains the scheduled removal of the shaper driver.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the virtual CAN bus (vcan) network driver.
The vcan device is just a loopback device for CAN frames, no
real CAN hardware is involved.
Signed-off-by: Oliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: Urs Thuermann <urs.thuermann@volkswagen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver for ethernet on mpc5200/mpc5200b SoCs (FEC).
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This gets rid of the lguest bus, drivers and DMA mechanism, to make
way for a generic virtio mechanism.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The network driver uses two virtqueues: one for input packets and one
for output packets. This has nice locking properties (ie. we don't do
any for recv vs send).
TODO:
1) Big packets.
2) Multi-client devices (maybe separate driver?).
3) Resolve freeing of old xmit skbs (Christian Borntraeger)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: netdev@vger.kernel.org
New version which uses less locking and drops old API
Signed-off-by: Matteo Croce <technoboy85@gmail.com>
Signed-off-by: Eugene Konev <ejka@imfi.kspu.ru>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With cleanup suggestions and bugs spotted by Stephen Hemminger,
Ingo Oeser, Matheos Worku, and Oliver Hartkopp.
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop building and configuring driver for Digi RightSwitch, which was
never actually sold to anyone, and remove it from MAINTAINERS.
In response to an investigation into the firmware of the "Digi Rightswitch"
driver, Andres Salomon discovered:
>
> Dear Andres:
>
> After further research, we found that this product was killed in place
> and never reached the market. We would like to request that this not be
> included.
Since the product never reached market, clearly nobody is using this orphaned
driver.
Signed-off-by: Nathanael Nerode <neroden@gcc.gnu.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Rename NET_SB1250_MAC to SB1250_MAC to follow the convention.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs. The
same ASIC is also found in the Axon bridge chip. This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging. Specifically:
- Should be adjusted to properly use the dma mapping API.
Axon needs this.
- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices. The dependencies here between
EMAC, MAL, ZMII etc. make this complicated. At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jesse Huang <jesse@icplus.com.tw>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Intel 82598 PCI-Express 10GbE
chipset. Devices will be available on the market soon.
This version of the driver is largely the same as the last release:
* Driver uses a single RX and single TX queue, each using 1 MSI-X
irq vector.
* Driver runs in NAPI mode only
* Driver is largely multiqueue-ready (TM)
Changes since 20070803:
* removed wrappers for hardware functions
* incorporated e1000e-style HW api reorganization code
* sparse/checkpatch cleanups, namespace cleanups
* driver prints out extra debugging information at load time
identifying adapter board number, mac, phy types
* removed ixgbe_api.c, ixgbe_api.h, ixgbe_osdep.h
* driver update to 1.1.18
* removed ixgbe.txt which contained no useful info anymore
[ Integrated napi_struct changes from Auke as well... -DaveM ]
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver implements support for the ICH9 on-board LAN ethernet
device. The device is similar to ICH8.
The driver encompasses code to support 82571/2/3, es2lan and ICH8
devices as well, but those device IDs are disabled and will be
"lifted" from the e1000 driver over one at a time once this driver
receives some more live time.
Changes to the last snapshot posted are exclusively in the internal
hardware API organization. Many thanks to Jeff Garzik for jumping in
and getting this organized with a keen eye on the future layout.
[ Integrated napi_struct patch from Auke as well... -DaveM ]
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Veth stands for Virtual ETHernet. It is a simple tunnel driver
that works at the link layer and looks like a pair of ethernet
devices interconnected with each other.
Mainly it allows to communicate between network namespaces but
it can be used as is as well.
The newlink callback is organized that way to make it easy to
create the peer device in the separate namespace when we have
them in kernel.
This implementation uses another interface - the RTM_NRELINK
message introduced by Patric.
Bug fixes from Daniel Lezcano.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit e1abecc489.
The driver works on some hardware that skge doesn't handle yet.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Gabriel C reports lguest doesn't compile with CONFIG_BLOCK=n. Fix this
by introducing a config var for the block device, which depends on
LGUEST && BLOCK. Do the same for the net driver, rather then depending
gratuitously on CONFIG_NET.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Gabriel C <nix.or.die@googlemail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The patch enables statistics in ucc_geth and adds ethtool support to
ucc_geth driver.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Lguest net driver
A simple net driver for lguest.
[akpm@linux-foundation.org: include fix]
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andi Kleen <ak@suse.de>
Cc: Jeff Garzik <jeff@garzik.org>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch implements the driver necessary use the Analog Devices
Blackfin processor's on-chip ethernet MAC controller.
[try#2]
- add timeout control
- kill dma_config_reg bitfields
- some trivial cleanup
[try#3]
- add endianess check
- add DRV_NAME, DRV_VERSION... driver information string
- add some comments for silicon anomaly and dma API confusion
- some code trivial cleanup
[try#4]
- add Blackfin latest GPIO pin mux opertion with Michael Hennerich's
help and Dan's review
- rewrite the DMA descriptor list operation in a more readable way
by Joe's review
[try#5]
- cleanup some coding style by Joe's review.
[try#6]
- 1.1 version fix a bug when set up multicast list pointed by Mr. yoshfuji
- rearrange the desc_list_free function.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Joe Perches <joe@perches.com>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The network device frontend driver allows the kernel to access network
devices exported exported by a virtual machine containing a physical
network device driver.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: Ian Pratt <ian.pratt@xensource.com>
Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Keir Fraser <Keir.Fraser@cl.cam.ac.uk>
Cc: netdev@vger.kernel.org
* 'for-linus' of git://git.kernel.dk/data/git/linux-2.6-block:
splice: direct splicing updates ppos twice
more ACSI removal
umem: Fix match of pci_ids in umem driver
umem: Remove references to dead CONFIG_MM_MAP_MEMORY variable
remove the documentation for the legacy CDROM drivers
This patch removes some code that became dead code after the ATARI_ACSI
removal.
It also indirectly fixes the following bug introduced by
commit c2bcf3b8978c291e1b7f6499475c8403a259d4d6:
config ATARI_SLM
tristate "Atari SLM laser printer support"
- depends on ATARI && ATARI_ACSI!=n
+ depends on ATARI
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Add macvlan driver, which allows to create virtual ethernet devices
based on MAC address.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver handles only L2TP data frames; control frames are handled
by a userspace application. It implements L2TP using the PPPoX socket
family. There is a PPPoX socket for each L2TP session in an L2TP
tunnel. PPP data within each session is passed through the kernel's
PPP subsystem via this driver. Kernel parameters of each socket can be
read or modified using ioctl() or [gs]etsockopt() calls.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hi,
This is the third submission of the network driver for PS3.
The differences from the previous one are:
- renamed source file names so that their prefix can match
with the module name
- added cbe-oss-dev@ozlabs.org line for MAINTAINER file
- changed some in copyright comments
If there are no more comments, please apply for 2.6.23.
Thank you
--
Subject: PS3: Ethernet driver
From: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Add Gigabit Ethernet support for the PS3 game console. The module will
be called ps3_gelic.
CC: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Support for the Asix AX88796 network controller, an
NE2000 compatible 10/100 ethernet device with internal
PHY.
The driver supports PHY settings via either ioctl() or
the ethtool driver ops.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Changes to last version:
- spelling fix
- cleaned up probe code
Thomas.
Ethernet driver for EISA only SNI RM200/RM400 machines
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters
IB: Put rlimit accounting struct in struct ib_umem
IB/uverbs: Export ib_umem_get()/ib_umem_release() to modules
It is preferable to group drivers by usage (net, scsi, ATA, ...) than
by bus. When reviewing drivers, the [PCI|USB|PCMCIA|...] maintainer
is probably less qualified on networking issues than a networking
maintainer. Also, from a practical standpoint, chips often
appear on multiple buses, which is why we do not put drivers into
drivers/pci/net.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add an InfiniBand driver for Mellanox ConnectX adapters. Because
these adapters can also be used as ethernet NICs and Fibre Channel
HBAs, the driver is split into two modules:
mlx4_core: Handles low-level things like device initialization and
processing firmware commands. Also controls resource allocation
so that the InfiniBand, ethernet and FC functions can share a
device without stepping on each other.
mlx4_ib: Handles InfiniBand-specific things; plugs into the
InfiniBand midlayer.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
migrate ucc_geth to use the common phylib code.
There are several side effects from doing this:
o deprecate 'interface' property specification present
in some old device tree source files in
favour of a split 'max-speed' and 'interface-type'
description to appropriately match definitions
in include/linux/phy.h. Note that 'interface' property
is still honoured if max-speed or interface-type
are not present (backward compatible).
o compile-time CONFIG_UGETH_HAS_GIGA is eliminated
in favour of probe time speed derivation logic.
o adjust_link streamlined to only operate on maccfg2
and upsmr.r10m, instead of reapplying static initial
values related to the interface-type.
o Addition of UEC MDIO of_platform driver requires
platform code add 'mdio' type to id list
prior to calling of_platform_bus_probe (separate patch).
o ucc_struct_init introduced to reduce ucc_geth_startup
complexity.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch refactors the wireless Kconfig all over and already
introduces net/wireless/Kconfig with just the WEXT bit for now,
the cfg80211 patch will add to that as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is a modified version of the Attansic reference driver
for the L1 ethernet adapter. Attansic has granted permission for
its inclusion in the mainline kernel.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Driver for the PA Semi PWRficient on-chip Ethernet (1/10G)
Basic enablement, will be complemented with performance enhancements
over time. PHY support will be added as well.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The OAKNET driver:
- has been marked as BROKEN for more than two years and
- is still marked as BROKEN.
Drivers that had been marked as BROKEN for such a long time seem to be
unlikely to be revived in the forseeable future.
But if anyone wants to ever revive this driver, the code is still
present in the older kernel releases.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This driver is required by the Chelsio T3 RDMA driver posted by
Steve Wise.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The SKMC driver has:
- already been marked as BROKEN in 2.6.0 three years ago and
- is still marked as BROKEN.
Drivers that had been marked as BROKEN for such a long time seem to be
unlikely to be revived in the forseeable future.
But if anyone wants to ever revive this driver, the code is still
present in the older kernel releases.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a driver for the Silan SC92031/Rsltek 8139D NIC chip.
This chip is found on at least one counterfeit Encore ENL832-TX-RENT NIC
[1], which came with a mini-CD with the 2.4 driver. A slightly older
version of the driver was found at [2]. The main difference between them
is that the newer one has a small bugfix in the RX path, a lot of
gratuitous renaming of functions, all the printable strings changed to show
as a "Rsltek 8139D" [sic], and a PCI ID of 8139 instead of 2031. The
driver on this patch is a rewrite of the vendor drivers (based mostly on
the older one).
Changes from the previous patch sent to netdev:
- Use MMIO instead of PIO
- Changed TX bounce buffers allocation
- Use skb_copy_and_csum_dev
- Several small bug fixes
- Tested for more than just a few minutes each time
[1] See http://www.encore-usa.com/faq.php under ENL832-TX-RENT for more
information
[2] Look for SL_LINUX.ZIP (which is really a .tar.gz) at
http://broadbandforum.in/dataone_Intex_LAN_cardlinux-t4207-s15.html
[3] To compile on 2.6.17, simply add back the last argument to the
interrupt handler in two places, and copy the boolean declarations
from 2.6.19
[akpm@osdl.org: build fixes]
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Driver for the Atmel MACB on-chip ethernet module.
Tested on AVR32/AT32AP7000/ATSTK1000. I've heard rumours that it works
with AT91SAM9260 as well, and it may be possible to share some code with
the at91_ether driver for AT91RM9200.
Hardware documentation can be found in the AT32AP7000 data sheet,
which can be downloaded from
http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
Changes since previous version:
* Probe for PHY ID instead of depending on it being provided through
platform_data.
* Grab initial ethernet address from the MACB registers instead
of depending on platform_data.
* Set MII/RMII mode correctly.
These changes are mostly about making the driver more compatible with
the at91 infrastructure.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add tsi108/9 on chip Ethernet controller driver support.
The driver code collects the feedback of previous posting form the mailing
list and gives the update.
MPC7448HPC2 platform in arch/powerpc uses tsi108 bridge.
The following is a brief description of the Ethernet controller:
The Tsi108/9 Ethernet Controller connects Switch Fabric to two independent
Gigabit Ethernet ports,E0 and E1. It uses a single Management interface to
manage the two physical connection devices (PHYs). Each Ethernet port has
its own statistics monitor that tracks and reports key interface
statistics. Each port supports a 256-entry hash table for address
filtering. In addition, each port is bridged to the Switch Fabric through
a 2-Kbyte transmit FIFO and a 4-Kbyte Receive FIFO.
Each Ethernet port also has a pair of internal Ethernet DMA channels to
support the transmit and receive data flows. The Ethernet DMA channels use
descriptors set up in memory, the memory map of the device, and access via
the Switch Fabric. The Ethernet Controller’s DMA arbiter handles
arbitration for the Switch Fabric. The Controller also has a register bus
interface for register accesses and status monitor control.
The PMD (Physical Media Device) interface operates in MII, GMII, or TBI
modes. The MII mode is used for connecting with 10 or 100 Mbit/s PMDs.
The GMII and TBI modes are used to connect with Gigabit PMDs. Internal
data flows to and from the Ethernet Controller through the Switch Fabric.
Each
Ethernet port uses its transmit and receive DMA channels to manage data
flows through buffer descriptors that are predefined by the system (the
descriptors can exist anywhere in the system memory map). These
descriptors are data structures that point to buffers filled with data
ready to transmit over Ethernet, or they point to empty buffers ready to
receive data from Ethernet.
Signed-off-by: Alexandre Bounine <Alexandre.Bounine@tundra.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The rest of 8390 conversions; ifdef cascade in 8390.h is gone now.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
more 8390 conversions - mac8390, zorro8390 and hydra got the same treatment
as arm etherh; one more case in 8390.h ifdef cascade is gone.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
etherh and a handful of other odd drivers use different macros when building
8390.c. Since we generate a single 8390.o and then link with it, in any
config with both oddball and normal 8390-based driver we will end up with
breakage in at least one of them. Solution: take most of 8390.c into
lib8390.c and have 8390.c, etherh.c and the rest of oddballs #include it.
Helper macros are taken from 8390.h to whoever includes lib8390.c. That
way odd drivers get separate instances of compiled 8390 stuff and stop
stepping on each other's toes. 8390.h gets cleaned up - we don't have
the cascade of ifdefs in there and are left with the stuff that can be
used by any 8390-based driver. Current problems are exactly because of
that cascade - we attempt to choose the set of helpers by looking at config
and that, of course, doesn't work well when we have several sets needed
by various drivers in our config.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Code for the EV96100 evaluation board hasn't compiled since at least
November 15, 2003, so it is being deleted as of 2.6.18 due to lack of
a user base.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
QE(QUICC Engine) is a new generation communication coprocessor, which can
be found on some of the latest Freescale PowerQUICC CPUs(e.g. MPC8360).
The UCC(Unified Communications Controller) module of QE can work as gigabit
Ethernet device. This patch provides driver for the device.
Signed-off-by: Shlomi Gridish <gridish@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a complementary network driver for our ISP4XXX parts.
There is a concurrent effort underway to get the iSCSI driver (qla4xxx)
integrated upstream as well.
I have been through several iterations with the linux-netdev list and have had
much response from Stephen Hemminger.
- Built and tested using kernel 2.6.17-rc4.
- The chip supports two ethernet and two iSCSI functions.
- The functions ql_sem_lock, ql_sem_spinlock, ql_sem_unlock, and
ql_wait_for_drvr_lock are used to protect resources that are shared across
the network and iSCSI functions. This protection is mostly during chip
initialization and resets, but also include link management.
- The PHY/MII are not exported through ethtool due to the fact that the
iSCSI function will control the common link at least 50% of the time.
This driver has been through several iterations on the netdev list and we feel
this driver is ready for inclusion in the upstream kernel.
It has been built and tested on x86 and PPC64 platforms.
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert selection of serial line header compression to use CONFIG_SLHC
rather than makefile ifeq uglyness. This makes it easier to select
the SLHC module from other code.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a patch for the Hilscher netx builtin ethernet ports. The
netx board support was merged into 2.6.17-git2.
The netx is a arm926 based SoC.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
--
drivers/net/Kconfig | 11
drivers/net/Makefile | 1
drivers/net/netx-eth.c | 516 ++++++++++++++++++++++++++++++++++++++++
include/asm-arm/arch-netx/eth.h | 27 ++
4 files changed, 555 insertions(+)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
>
> The patch was badly wordwrapped. Please fix and resend.
>
OK, I've fixed the wrapping and removed the CONFIG_ARM restriction. I've also did my
best to modify the C style to conform to the comments.
I noticed that the patch is getting ignored by majordomo due to its size >100K.
Should it be broken up somehow to allow posting to the lists?
Signed-off-by: Dustin McIntire <dustin@sensoria.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A new device to do intermidiate functional block in a system shared
manner. To use the new functionality, you need to turn on
qos/classifier actions.
The new functionality can be grouped as:
1) qdiscs/policies that are per device as opposed to system wide. ifb
allows for a device which can be redirected to thus providing an
impression of sharing.
2) Allows for queueing incoming traffic for shaping instead of
dropping.
Packets are redirected to this device using tc/action mirred redirect
construct. If they are sent to it by plain routing instead then they
will merely be dropped and the stats would indicate that.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
The way the hardware and firmware work is that there is one shared RX
queue and IRQ for a number of different network interfaces. Due to this,
we would like to process received packets for every interface in the same
NAPI poll handler, so we need a pseudo-device to schedule polling on.
What the driver currently does is that it always schedules polling for
the first network interface in the list, and processes packets for every
interface in the poll handler for that first interface -- however, this
scheme breaks down if the first network interface happens to not be up,
since netif_rx_schedule_prep() checks netif_running().
sky2 apparently has the same issue, and Stephen Hemminger suggested a
way to work around this: create a variant of netif_rx_schedule_prep()
that does not check netif_running(). I implemented this locally and
called it netif_rx_schedule_prep_notup(), and it seems to work well,
but it's something that probably not everyone would be happy with.
The ixp2000 is an ARM CPU with a high-speed network interface in the
CPU itself (full duplex 4Gb/s or 10Gb/s depending on the IXP model.)
The CPU package also contains 8 or 16 (again depending on the IXP
model) 'microengines', which are somewhat primitive but very fast
and efficient processor cores which can be used to offload various
things from the main CPU.
This driver makes the high-speed network interface in the CPU visible
and usable as a regular linux network device. Currently, it only
supports the Radisys ENP2611 IXP board, but adding support for other
board types should be fairly easy.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This seems to have gotten lost, so I'll resend.
Signed-off-by: Andy Fleming <afleming@freescale.com>
* Added sysfs support to gianfar for modifying FIFO and stashing parameters
* Updated driver to support 10 Mbit, full duplex operation
* Improved comments throughout
* Cleaned up and optimized offloading code
* Fixed a bug where rx buffers were being improperly mapped and unmapped
* (only manifested if cache-coherency was off)
* Added support for using the eTSEC exact-match MAC registers
* Bumped the version to 1.3
* Added support for distinguishing between reduced 100 and 10 Mbit modes
* Modified default coalescing values to lower latency
* Added documentation
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
From: Matt Domsch <Matt_Domsch@dell.com>
The patch below implements the Microsoft Point-to-Point Encryption method
as a PPP compressor/decompressor. This is necessary for Linux clients and
servers to interoperate with Microsoft Point-to-Point Tunneling Protocol
(PPTP) servers (either Microsoft PPTP servers or the poptop project) which
use MPPE to encrypt data when creating a VPN.
This patch differs from the kernel_ppp_mppe DKMS pacakge at
pptpclient.sourceforge.net by utilizing the kernel crypto routines rather
than providing its own SHA1 and arcfour implementations.
Minor changes to ppp_generic.c try to prevent a link from disabling
compression (in our case, the encryption) after it has started using
compression (encryption).
Feedback to <pptpclient-devel@lists.sourceforge.net> please.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Cc: James Cameron <james.cameron@hp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Written by Adrian Sun (asun@darksunrising.com).
Ported to 2.6.x by Tom 'spot' Callaway <tcallawa@redhat.com>.
Further cleaned up and integrated by David S. Miller
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds an "Ethernet" driver which sends Ethernet packets over the standard
RapidIO messaging. This depends on the core RIO patch for mailbox/doorbell
access.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds a driver for a new 1000 Mbit ethernet NIC. It is
integrated on the south bridge that is used for our Cell Blades.
The code gets the MAC address from the Open Firmware device tree, so it
won't compile on platforms other than ppc64.
This is the first public release, so I don't expect the first version to
get merged, but I'd aim for integration within the 2.6.13 time frame.
Cc: Utz Bacher <utz.bacher@de.ibm.com>
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
David S. Miller