Since mesh powersaving was added, pending bcast/mcast frames may go out the
CAB queue now. Unfortunately, the queue was only set up for AP mode, so we
would try to tx on the IEEE80211_INVAL_HW_QUEUE. Allow cab_queue for mesh
interfaces as well.
Fixes the following warning (or crash without MAC80211_VERBOSE_DEBUG):
WARNING: at net/mac80211/tx.c:1223 __ieee80211_tx+0x162/0x35f [mac80211]()
Modules linked in: mac80211_hwsim mac80211 cfg80211 [...]
Pid: 3085, comm: avahi-daemon Tainted: G W 3.8.0-rc1+ #377
Call Trace:
[<ffffffff81045c20>] warn_slowpath_common+0x83/0x9c
[<ffffffff81045c53>] warn_slowpath_null+0x1a/0x1c
[<ffffffffa083aef0>] __ieee80211_tx+0x162/0x35f [mac80211]
[<ffffffffa083cb1d>] ieee80211_tx+0xd3/0xf9 [mac80211]
[<ffffffffa083cc0f>] ieee80211_xmit+0xcc/0xd5 [mac80211]
[<ffffffffa083db59>] ieee80211_subif_start_xmit+0xc53/0xcd8 [mac80211]
[<ffffffff81319acd>] dev_hard_start_xmit+0x259/0x3ce
[<ffffffff81333d6b>] sch_direct_xmit+0x74/0x17d
[<ffffffff8131a0b1>] dev_queue_xmit+0x230/0x414
[<ffffffff8134877a>] ip_finish_output2+0x348/0x3aa
[<ffffffff81349029>] ip_finish_output+0x6c/0x71
[<ffffffff81349046>] NF_HOOK_COND.constprop.44+0x18/0x58
[<ffffffff8134a03a>] ip_mc_output+0x134/0x13c
[<ffffffff8134835a>] dst_output+0x18/0x1c
[<ffffffff81349a24>] ip_local_out+0x20/0x24
[<ffffffff8134a8cf>] ip_send_skb+0x16/0x3c
[<ffffffff8136bfba>] udp_send_skb+0x254/0x2b9
[<ffffffff8136c85e>] udp_sendmsg+0x5a8/0x7d4
Signed-off-by: Bob Copeland <bob@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the vlan device is removed, ps->bc_buf processing can no longer
send its frames.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add command to trigger radar detection in the driver/FW.
Once radar detection is started it should continuously
monitor for radars as long as the channel active.
If radar is detected usermode notified with 'radar
detected' event.
Scanning and remain on channel functionality must be disabled
while doing radar detection/scanning, and vice versa.
Based on original patch by Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that we have channel contexts, idle is (pretty
much) equivalent to not having a channel context.
Change the code to use this relation so that there
no longer is a need for a lot of idle recalculate
calls everywhere.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are only a few drivers that use HW scan, and
all of those don't need a non-idle transition before
starting the scan -- some don't even care about idle
at all. Remove the flag and code associated with it.
The only driver that really actually needed this is
wl1251 and it can just do it itself in the hw_scan
callback -- implement that.
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add debugfs driver callbacks so drivers can add
debugfs entries for interfaces. Note that they
_must_ remove the entries again as add/remove in
the driver doesn't correspond to add/remove in
debugfs; the former is up/down while the latter
is netdev create/destroy.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Depending on the driver, having ARP filtering for
some addresses may be possible. Remove the logic
that tracks whether ARP filter is enabled or not
and give the driver the total number of addresses
instead of the length of the list so it can make
its own decision.
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of checking every time bss_info_changed is called,
assign the pointer once depending on the interface type
and then leave it untouched until the interface type is
changed. This makes the ieee80211_bss_info_change_notify()
now a simple wrapper to call the driver only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If there are VLANs, stopping an AP is inefficient as it
calls rcu_barrier() once for each interface (the VLANs
and the AP itself). Optimise this by moving rcu_barrier()
out of the station cleanups and calling it only once for
all interfaces combined.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The last fixes re-added the RCU synchronize penalty
on roaming to fix the races. Split up sta_info_flush()
now to get rid of that again, and let managed mode
(and only it) delay the actual destruction.
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an interface is brought down it must have been
disconnected (or similar) in all modes other than WDS,
so warn if any stations were removed in other modes.
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When all interfaces have been removed, there can't
be any stations left over, so there's no need to
flush again. Remove this, and all code associated
with it, which also simplifies the function.
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The maximum MTU shouldn't take the headers into account,
the maximum MSDU size is exactly the maximum MTU.
Signed-off-by: T Krishna Chaitanya <chaitanyatk@posedge.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Unfortunately, commit b22cfcfcae, intended to speed up roaming
by avoiding the synchronize_rcu() broke AP/mesh modes as it moved
some code into that work item that will still call into the driver
at a time where it's no longer expected to handle this: after the
AP or mesh has been stopped.
To fix this problem remove the per-station work struct, maintain a
station cleanup list instead and flush this list when stations are
flushed. To keep this patch smaller for stable, do this when the
stations are flushed (sta_info_flush()). This unfortunately brings
back the original roaming delay; I'll fix that again in a separate
patch.
Also, Ben reported that the original commit could sometimes (with
many interfaces) cause long delays when an interface is set down,
due to blocking on flush_workqueue(). Since we now maintain the
cleanup list, this particular change of the original patch can be
reverted.
Cc: stable@vger.kernel.org [3.7]
Reported-by: Ben Greear <greearb@candelatech.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make AP_VLAN type interfaces track the AP master channel
context so they have one assigned for the various lookups.
Don't give them their own refcount etc. since they're just
slaves to the AP master.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the sdata work is pending while the interface is stopped,
we currently flush it. If it's not running this means waiting
for it to run, which could take a while if the workqueue is
backlogged. However, the work exits right away if it starts
to run while the interface is already stopping. There's no
point in waiting for that, so use cancel_work_sync() instead.
Reported-by: Ben Greear <greearb@candelatech.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a driver registers an address mask we should ensure that no
interface gets an address assigned that isn't covered by the
registered address mask. This prevents invalid configurations
from reaching the device and causing problems.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
[change function flow to reduce indentation, fix locking]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Convert mac80211 (and where necessary, some drivers a
little bit) to the new channel definition struct.
This will allow extending mac80211 for VHT, which is
currently restricted to channel contexts since there
are no drivers using that which makes it easier. As
I also don't care about VHT for drivers not using the
channel context API, I won't convert the previous API
to VHT support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even before channel contexts/multi-channel, having a
single global TX power limit was already problematic,
in particular if two managed interfaces connected to
two APs with different power constraints. The channel
context introduction completely broke this though and
in fact I had disabled TX power configuration there
for drivers using channel contexts.
Change everything to track TX power per interface so
that different user settings and different channel
maxima are treated correctly. Also continue tracking
the global TX power though for compatibility with
applications that attempt to configure the wiphy's
TX power globally.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since cfg80211 will now call the explicit stop_ap
operation when an AP interface goes down, move all
teardown code there and remove it from interface
handling. The only thing that needs to stay is the
code to dev_close() all dependent VLANs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch prepares mac80211 for a later implementation of mesh or
ad-hoc powersave clients.
The structures related to powersave (buffer, TIM map, counters) are
moved from the AP-specific interface structure to a generic structure
that can be embedded into any interface type.
The functions related to powersave are prepared to allow easy
extension with different interface types. For example with:
+ } else if (sta->sdata->vif.type == NL80211_IFTYPE_MESH_POINT) {
+ ps = &sdata->u.mesh.ps;
Some references to the AP's beacon structure are removed where they
were obviously not used.
The patch compiles without warning and has been briefly tested as AP
interface with one client in PS mode.
Signed-off-by: Marco Porsch <marco.porsch@etit.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On each channel that the device is operating on, it
may need to listen using one or more chains depending
on the SMPS settings of the interfaces using it. The
previous channel context changes completely removed
this ability (before, it was available as the SMPS
mode).
Add per-context tracking of the required static and
dynamic RX chains and notify the driver on changes.
To achieve this, track the chains and SMPS mode used
on each virtual interface and update the channel
context whenever this changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of operating on a single channel only,
use the new channel context infrastructure in
all mac80211 code.
This enables drivers that want to use the new
channel context infrastructure to use multiple
channels, while nothing should change for all
the other drivers that don't support it.
Right now this disables both TX power settings
and spatial multiplexing powersave. Both need
to be re-enabled on a channel context basis.
Additionally, when channel contexts are used
drop the connection when channel switch is
received rather than trying to handle it. This
will have to be improved later.
[With fixes from Eliad and Emmanuel incorporated]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Free tx status skbs when draining power save buffers, pending frames, or
when tearing down a vif.
Fixes remaining conditions that can lead to hostapd/wpa_supplicant hangs when
running out of socket write memory.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 calls synchronize_rcu() on sta deletion,
which increase the roaming time significantly.
Convert it into a call_rcu() mechanism, in order
to avoid blocking. Since some of the cleanup
functions might sleep, schedule from the call_rcu
callback a new work that will do the actual cleanup.
In order to make sure the cleanup occurs before
the interface went down, flush local->workqueue
on ieee80211_do_stop().
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A P2P Device interface does not have a netdev, and is not
expected to be used for transmitting data, so there is no
need to assign hw queues for it.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some devices like the current iwlwifi implementation
require that the P2P interface address match the P2P
Device address (only one P2P interface is supported.)
Add the HW flag IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF
that allows drivers to request that P2P Interfaces
added while a P2P Device is active get the same MAC
address by default.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After cfg80211 got a P2P Device abstraction, add
support to mac80211. Whether it really is supported
or not will depend on whether or not the driver has
support for it, but mac80211 needs to change to be
able to support drivers that need a P2P Device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support using a different MAC address
for the P2P Device address we must first have a
P2P Device abstraction that can be assigned a MAC
address.
This abstraction will also be useful to support
offloading P2P operations to the device, e.g.
periodic listen for discoverability.
Currently, the driver is responsible for assigning
a MAC address to the P2P Device, but this could be
changed by allowing a MAC address to be given to
the NEW_INTERFACE command.
As it has no associated netdev, a P2P Device can
only be identified by its wdev identifier but the
previous patches allowed using the wdev identifier
in various APIs, e.g. remain-on-channel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This could take a while (100ms+) and may delay sending assoc resp
in AP mode with WPS or P2P GO (as setting the probe resp takes place
there). We've encountered situations where the delay was big enough
to cause connection problems with devices like Galaxy Nexus.
Switch to using call_rcu with a free handler.
[Arik - rework to use plain buffer and instead of skb]
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function was only used by mesh, and not really needed since any
interface-specific cleanup already happens in the netdev handlers.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is not necessary to stop the mesh beacon in the mac80211 ndo_stop
handler, since cfg80211 has already left the mesh on NETDEV_GOING_DOWN
notification.
Also some improvements to ieee80211_stop_mesh():
- flush mpath entries.
- flush sta entries per-sdata so we don't remove entries belonging to
other vifs on the same hw.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Enable the carrier on WDS type interfaces only
after having added the station entry for the
WDS peer so outgoing frames will find it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of assuming the carrier is on all
the time in mesh manage it with joining
and leaving the mesh.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using hw.conf.channel is wrong as it could be the
temporary channel if any function like the beacon
get function is called while scanning or during
other temporary out-of-channel activities.
Use oper_channel instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 870d37fc22.
This code doesn't work as cfg80211 will call
set_monitor_enabled at the wrong time and it
doesn't seem to be possible to fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the virtual monitor interface is requested
by the driver, it should also be iterated over
when the driver wants to iterate all active
interfaces.
To allow that protect it with the iflist_mtx.
Change-Id: I58ac5de2f4ce93d12c5a98ecd2859f60158d5d69
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Making the scan_sdata pointer usable with RCU makes
it possible to dereference it in the RX path to see
if a received frame actually matches the interface
that is scanning. This is just preparations, making
the pointer __rcu.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to be able to create P2P Device wdevs, move
the virtual interface management over to wireless_dev
structures.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use cfg80211 the new .set_monitor_enabled instead
of tracking it inside mac80211.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since it's not called from any file outside where
it's defined, the function can be static if moved
up in the file before the callers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_check_concurrent_iface() need not use the
netdev. Remove the use of the netdev here to prepare
the function for P2P device addition.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a few things that make the logging and
debugging in mac80211 less useful than it should
be right now:
* a lot of messages should be pr_info, not pr_debug
* wholesale use of pr_debug makes it require *both*
Kconfig and dynamic configuration
* there are still a lot of ifdefs
* the style is very inconsistent, sometimes the
sdata->name is printed in front
Clean up everything, introducing new macros and
separating out the station MLME debugging into
a new Kconfig symbol.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Save and configure the wmm_acm per sdata, rather than
per hardware.
If wmm_acm is saved per hardware when running two
interfaces simultaneously on the same hardware one
interface's wmm policy will be affected by the other
interface.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Redesign all the off-channel code, getting rid of
the generic off-channel work concept, replacing
it with a simple remain-on-channel list.
This fixes a number of small issues with the ROC
implementation:
* offloaded remain-on-channel couldn't be queued,
now we can queue it as well, if needed
* in iwlwifi (the only user) offloaded ROC is
mutually exclusive with scanning, use the new
queue to handle that case -- I expect that it
will later depend on a HW flag
The bigger issue though is that there's a bad bug
in the current implementation: if we get a mgmt
TX request while HW roc is active, and this new
request has a wait time, we actually schedule a
software ROC instead since we can't guarantee the
existing offloaded ROC will still be that long.
To fix this, the queuing mechanism was needed.
The queuing mechanism for offloaded ROC isn't yet
optimal, ideally we should add API to have the HW
extend the ROC if needed. We could add that later
but for now use a software implementation.
Overall, this unifies the behaviour between the
offloaded and software-implemented case as much
as possible.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The IDLE handling in HW off-channel is broken right
now since we turn off IDLE only when the off-channel
period already started. Therefore, all drivers that
use it today (only iwlwifi!) must support off-channel
while idle, so playing with idle isn't needed at all.
Off-channel in general, since it's no longer used for
authentication/association, shouldn't affect PS, so
also remove that logic.
Also document a small caveat for reporting TX status
from off-channel frames in HW remain-on-channel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Standardize the debugging to be able to use dynamic_debug.
Coalesce formats, align arguments.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Low level drivers can now set certain netdev feature bits in
netdev_features member of the ieee80211_hw struct. These will be
propagated to every netdev created from this HW.
The white-listed features currently include only ones related to HW
checksumming.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When any interface goes down, it could be the one that we
were doing a remain-on-channel with. We therefore need to
cancel the remain-on-channel and flush the related work
structs so they don't run after the interface has been
removed or even destroyed.
It's also possible in this case that an off-channel SKB
was never transmitted, so free it if this is the case.
Note that this can also happen if the driver finishes
the off-channel period without ever starting it.
Cc: stable@kernel.org
Reported-by: Nirav Shah <nirav.j2.shah@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My queue management rework broke drivers that don't
have multiple AC queues and register a single queue
only, causing a warning:
WARNING: at net/mac80211/iface.c:162 ieee80211_check_queues
This was due to filling the queues wrongly and then
noticing the error when checking later.
Reported-and-Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/e1000e/param.c
drivers/net/wireless/iwlwifi/iwl-agn-rx.c
drivers/net/wireless/iwlwifi/iwl-trans-pcie-rx.c
drivers/net/wireless/iwlwifi/iwl-trans.h
Resolved the iwlwifi conflict with mainline using 3-way diff posted
by John Linville and Stephen Rothwell. In 'net' we added a bug
fix to make iwlwifi report a more accurate skb->truesize but this
conflicted with RX path changes that happened meanwhile in net-next.
In e1000e a conflict arose in the validation code for settings of
adapter->itr. 'net-next' had more sophisticated logic so that
logic was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds hepler to clean sdata ieee80211_clean_sdata similar way as
ieee80211_setup_sdata is implemented. The function will be used by other
interfaces later.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 3a25a8c8 (mac80211: add improved HW queue control) introduced a
bug when running in AP mode without the IEEE80211_HW_QUEUE_CONTROL
flag set. The ieee80211_check_queues() function always returns
-EINVAL, preventing AP mode from starting. To fix this, check whether
this flag is set before checking if cab_queue is set properly.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliad's comment prompted me to look closer at
the error paths in ieee80211_do_open() and I
found one that should use the error labels.
Also add a comment about the clear_bit since
in many error cases the bit hasn't been set.
Cc: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 currently only supports one hardware queue
per AC. This is already problematic for off-channel
uses since if we go off channel while the BE queue
is full and then try to send an off-channel frame
the frame will never go out. This will become worse
when we support multi-channel since then a queue on
one channel might be full, but we have to stop the
software queue for all channels. That is obviously
not desirable.
To address this problem allow drivers to register
more hardware queues, and allow them to map them to
virtual interfaces. When they stop a hardware queue
the corresponding AC software queues on the correct
interfaces will be stopped as well. Additionally,
there's an off-channel queue to solve that problem
and a per-interface after-DTIM beacon queue. This
allows drivers to manage software queues closer to
how the hardware works.
Currently, there's a limit of 16 hardware queues.
This may or may not be sufficient, we can adjust it
as needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The queue mapping redesign that I'm planning to do
will break pure injection unless we handle monitor
interfaces explicitly. One possible option would
be to have the driver tell mac80211 about monitor
mode queues etc., but that would duplicate the API
since we already need to have queue assignments
handled per virtual interface.
So in order to solve this, have a virtual monitor
interface that is added whenever all active vifs
are monitors. We could also use the state of one
of the monitor interfaces, but managing that would
be complicated, so allocate separate state.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AP netdev is really only active when beaconing, so
manage the carrier state accordingly. Also do that for
VLAN interfaces enslaved to a given AP interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When comparing hw->queues to determine if the
device is QoS capable, use IEEE80211_NUM_ACS
instead of just 4.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we get more hardware queues, we'll still want
to only have netdev queues per AC, so set it up in
that way. If the hardware doesn't support QoS (by
not supporting at least 4 queues) the netdevs get
a single queue only (this is no change in behavior
as there are no drivers with 2 or 3 queues today.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When associating and particularly when disassociating
there's no need to notify the driver about changes
with multiple calls to bss_info_changed, we should
combine the QoS enabling/disabling into the same call
as otherwise the driver could get confused about QoS
suddenly getting disabled while connected.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When removing an interface while it is in the
process of authenticating or associating, we
leak the auth_data or assoc_data, and leave
the timer pending. The timer then crashes the
system when it fires as its data is gone.
Fix this by explicitly deleting all the data
when the interface is removed. This uncovered
another bug -- this problem should have been
detected by the sta_info_flush() warning but
that function doesn't ever return non-zero,
I'll fix that in a separate patch.
Reported-by: Hieu Nguyen <hieux.c.nguyen@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
nothing needs to be done for monitor/AP_VLAN mode on calling
ieee80211_bss_info_change_notify -> drv_bss_info_changed with the change
flag 'BSS_CHANGED_IDLE'. 'wl1271' seems to use BSS_CHANGED_IDLE only for
STA and IBSS mode. further the non-idle state of the monitor mode is
taken care by the 'count' variable which counts non-idle interfaces.
ieee80211_idle_off(local, "in use") will be called.
this fixes the following WARNING when we have initially STA mode
(network manager running) and not associated, and change it to monitor
mode with network manager disabled and bringing up the monitor mode.
this changes the idle state from 'true' (STA unassociated) to 'false'
(MONITOR mode)
exposed by the commit 405385f8ce
"mac80211: set bss_conf.idle when vif is connected"
WARNING: net/mac80211/main.c:212
ieee80211_bss_info_change_notify+0x1cf/0x330 [mac80211]()
Hardware name: 64756D6
Pid: 3835, comm: ifconfig Tainted: G O
3.3.0-rc3-wl #9
Call Trace:
[<c0133b02>] warn_slowpath_common+0x72/0xa0
[<fc8e8c3f>] ?
ieee80211_bss_info_change_notify+0x1cf/0x330 [mac80211]
[<fc8e8c3f>] ?
ieee80211_bss_info_change_notify+0x1cf/0x330 [mac80211]
[<c0133b52>] warn_slowpath_null+0x22/0x30
[<fc8e8c3f>]
ieee80211_bss_info_change_notify+0x1cf/0x330 [mac80211]
[<fc8f9de3>] __ieee80211_recalc_idle+0x113/0x430
[mac80211]
[<fc8fabc6>] ieee80211_do_open+0x156/0x7e0 [mac80211]
[<fc8f8a25>] ?
ieee80211_check_concurrent_iface+0x25/0x180 [mac80211]
[<c015dd9f>] ? raw_notifier_call_chain+0x1f/0x30
[<fc8fb290>] ieee80211_open+0x40/0x80 [mac80211]
[<c05894f6>] __dev_open+0x96/0xe0
[<c068fba5>] ? _raw_spin_unlock_bh+0x35/0x40
[<c05881d9>] __dev_change_flags+0x109/0x170
[<c0589423>] dev_change_flags+0x23/0x60
[<c05f3770>] devinet_ioctl+0x6a0/0x770
ieee80211 phy0: device no longer idle - in use
Cc: Eliad Peller <eliad@wizery.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, mac80211 goes to idle-off before starting a scan.
However, some devices that implement hw scan might not
need going idle-off in order to perform a hw scan, and
thus saving some energy and simplifying their state machine.
(Note that this is also the case for sched scan - it
currently doesn't make mac80211 go idle-off)
Add a new flag to indicate support for hw scan while idle.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the second part of the auth/assoc redesign,
the mac80211 part. This moves the auth/assoc code
out of the work abstraction and into the MLME, so
that we don't flip channels all the time etc.
The only downside is that when we are associated,
we need to drop the association in order to create
a connection to another AP, but for most drivers
this is actually desirable and the ability to do
was never used by any applications. If we want to
implement resource reservation with FT-OTA, we'd
probably best do it with explicit R-O-C in wpa_s.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Handle MCS masks set by the user.
* Match rates provided by the rate control algorithm to the mask set,
also in HT mode, and switch back to legacy mode if necessary.
* add debugfs files to observate the rate selection
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the future, when we start notifying drivers,
state transitions could potentially fail. To make
it easier to distinguish between programming bugs
and driver failures:
* rename sta_info_move_state() to
sta_info_pre_move_state() which can only be
called before the station is inserted (and
check this with a new station flag).
* rename sta_info_move_state_checked() to just
plain sta_info_move_state(), as it will be
the regular function that can fail for more
than just one reason (bad transition or an
error from the driver)
This makes the programming model easier -- one of
the functions can only be called before insertion
and can't fail, the other can fail.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
__ieee80211_recalc_idle() iterates through the vifs,
sets bss_conf.idle = true if they are disconnected,
and increases "count" if they are not (which later
gets evaluated in order to determine whether the
device is idle).
However, the loop doesn't set bss_conf.idle = false
(along with increasing "count"), causing the device
idle state and the vif idle state to get out of sync
in some cases.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Station entries can have various states, the most
important ones being auth, assoc and authorized.
This patch prepares us for telling the driver about
these states, we don't want to confuse drivers with
strange transitions, so with this we enforce that
they move in the right order between them (back and
forth); some transitions might happen before the
driver even knows about the station, but at least
runtime transitions will be ordered correctly.
As a consequence, IBSS and MESH stations will now
have the ASSOC flag set (so they can transition to
AUTHORIZED), and we can get rid of a special case
in TX processing.
When freeing a station, unwind the state so that
other parts of the code (or drivers later) can rely
on the transitions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can't rely on ieee80211_select_queue() to do its job at this point
since the skb->protocol is not yet known. Instead, factor out and reuse
the queue mapping logic for injected frames.
Also, to mitigate congestion, forwarded frames should be dropped if the
outgoing queue was stopped. This was not correctly implemented as we
were not checking the right queue. Furthermore, we were dropping frames
that had arrived to their destination if that queue was stopped.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch contains the processing changes in mac80211.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sk_buff structs should be freed using kfree_skb().
This was introduced recently in 029458212 "mac80211: Save probe
response data for bss".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow setting a probe response template for an interface operating in
AP mode. Low level drivers are notified about changes in the probe
response template and are able to retrieve a copy of the current probe
response. This data can, for example, be uploaded to hardware as a
template.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 should set carrier_on for ibss vifs
only while they are joined (similar to sta vifs)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will allow us to support dynamic WEP with 802.1X
properly in mac80211 by not encrypting outgoing and
accepting unencrypted incoming frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver is never informed about monitor or
AP_VLAN interfaces, so whenever we pass those
to it later this is a bug. Verify we don't as
there are some cases where this could happen.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 calls ieee80211_set_wmm_default (which in turn
calls drv_conf_tx()) for every new interface, including
"internal" ones (e.g. monitor interface, which the low-level
driver doesn't know about).
Limit this call only to valid interfaces.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The flaglock in struct sta_info has long been
something that I wanted to get rid of, this
finally does the conversion to atomic bitops.
The conversion itself is straight-forward in
most places, a few things needed to change a
bit since we can no longer use multiple bits
at the same time.
On x86-64, this is a fairly significant code
size reduction:
text data bss dec hex
427861 23648 1008 452517 6e7a5 before
425383 23648 976 450007 6ddd7 after
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an AP interface is removed without the
AP/VLAN interfaces having been removed before
already, the AP-VLAN interface might still
have sleeping stations and buffer multicast
frames which will happen on the AP interface.
Thus, we need to remove AP/VLAN interfaces
before purging buffered broadcast frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an interface is removed, the mesh paths associated with it should
also be removed.
This fixes a bug we observed when reloading a device driver module
without reloading mac80211s.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When assigning a NULL value to an RCU protected pointer, no barrier
is needed. The rcu_assign_pointer, used to handle that but will soon
change to not handle the special case.
Convert all rcu_assign_pointer of NULL value.
//smpl
@@ expression P; @@
- rcu_assign_pointer(P, NULL)
+ RCU_INIT_POINTER(P, NULL)
// </smpl>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the last patch, We are left in a state in which only drivers calling
ether_setup have IFF_TX_SKB_SHARING set (we assume that drivers touching real
hardware call ether_setup for their net_devices and don't hold any state in
their skbs. There are a handful of drivers that violate this assumption of
course, and need to be fixed up. This patch identifies those drivers, and marks
them as not being able to support the safe transmission of skbs by clearning the
IFF_TX_SKB_SHARING flag in priv_flags
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Karsten Keil <isdn@linux-pingi.de>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Patrick McHardy <kaber@trash.net>
CC: Krzysztof Halasa <khc@pm.waw.pl>
CC: "John W. Linville" <linville@tuxdriver.com>
CC: Greg Kroah-Hartman <gregkh@suse.de>
CC: Marcel Holtmann <marcel@holtmann.org>
CC: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
is_valid_ether_addr itself checks for is_zero_ether_addr
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't have multiple RX queues, so there's no use
in allocating multiple, use alloc_netdev_mqs() to
allocate multiple TX but only one RX queue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This partially reverts 1c5cae815d, because
the netdev name is copied into sdata->name, which is used for debugging
messages, for example. Otherwise, we get messages like this:
wlan%d: authenticated
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Jiri Pirko <jpirko@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As long as no delay is required b/w channel change, scan work
is proceeding without scheduling a new work. In such case, we
can not abort scan work when the card was unplugged. This patch
completes the scanning immediately whenever the device goes down.
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds sparse RCU annotations to most of
mac80211, only the mesh code remains to be
done.
Due the the previous patches, the annotations
are pretty simple. The only thing that this
actually changes is removing the RCU usage of
key->sta in debugfs since this pointer isn't
actually an RCU-managed pointer (it only has
a single assignment done before the key even
goes live). As that is otherwise harmless, I
decided to make it part of this patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Force dev_alloc_name() to be called from register_netdevice() by
dev_get_valid_name(). That allows to remove multiple explicit
dev_alloc_name() calls.
The possibility to call dev_alloc_name in advance remains.
This also fixes veth creation regresion caused by
84c49d8c3e
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Eric W. Biederman <ebiederm@xmission.com>
In the beginning with batching unreg_list was a list that was used only
once in the lifetime of a network device (I think). Now we have calls
using the unreg_list that can happen multiple times in the life of a
network device like dev_deactivate and dev_close that are also using the
unreg_list. In addition in unregister_netdevice_queue we also do a
list_move because for devices like veth pairs it is possible that
unregister_netdevice_queue will be called multiple times.
So I think the change below to fix dev_deactivate which Eric D. missed
will fix this problem. Now to go test that.
Signed-off-by: David S. Miller <davem@davemloft.net>
When a vif goes away, it could cause the super-chan
to be recalculated differently, so do that calculation
on iface removal.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows drivers to support remain-on-channel
offload if they implement smarter timing or need
to use a device implementation like iwlwifi.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The throughput LED trigger was always active when
the radio was enabled. In most cases that's likely
the desired behaviour, but iwlwifi requires it to
be only active when one of the virtual interfaces
is actually "connected" in some way.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi and other drivers like to blink their LED
based on throughput. Implement this generically in
mac80211, based on a throughput table the driver
specifies. That way, drivers can set the blink
frequencies depending on their desired behaviour
and max throughput.
All the drivers need to do is provide an LED class
device, best with blink hardware offload.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of tying mesh activity to interface up,
add join and leave commands for mesh. Since we
must be backward compatible, let cfg80211 handle
joining a mesh if a mesh ID was pre-configured
when the device goes up.
Note that this therefore must modify mac80211 as
well since mac80211 needs to lose the logic to
start the mesh on interface up.
We now allow querying mesh parameters before the
mesh is connected, which simply returns defaults.
Setting them (internally renamed to "update") is
only allowed while connected. Specify them with
the new mesh join command instead where needed.
In mac80211, beaconing must now also follow the
mesh enabled/not enabled state, which is done
by testing the mesh ID.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Logically, the filter adjusting belongs with
starting/stopping mesh, not interface up/down,
so move it there.
Tested-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For client STA interfaces, ieee80211_do_stop unsets the relevant
interface's SDATA_STATE_RUNNING state bit prior to cancelling an
interrupted scan. When ieee80211_offchannel_return is invoked as
part of cancelling the scan, it doesn't bother unsetting the
SDATA_STATE_OFFCHANNEL bit because it sees that the interface is
down. Normally this doesn't matter because when the client STA
interface is brought back up, it will probably issue a scan. But
in some cases (e.g., the user changes the interface type while it
is down), the SDATA_STATE_OFFCHANNEL bit will remain set. This
prevents the interface queues from being started. So we
cancel the scan before unsetting the SDATA_STATE_RUNNING bit.
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using the frame registration notification, we
can see when probe requests are requested and
notify the low-level driver via filtering. The
flag is also set in AP and IBSS modes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When roaming while we have active BA session,
we can end up transmitting delBA frames to
the old AP while we're already on the new AP's
channel, which can cause warnings.
Simply avoid sending those frames, but still
tear down the internal session state, since
they are not really necessary anyway as we
will implicitly disassociate when sending the
association to the new AP.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize the rate table for WDS interfaces, and
add cases to allow WDS packets to pass the xmit and receive
tests.
Signed-off-by: Bill Jordan <bjordan@rajant.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an refcounting bug. Previously it
was possible to corrupt the per-device recv. filter
and monitor management counters when:
iw dev wlanX set monitor [new flags]
was issued on an active monitor interface.
Acked-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a driver advertises p2p device support,
mac80211 will handle it, but internally it will
rewrite the interface type to STA/AP rather than
P2P-STA/GO since otherwise a lot of paths need
to be touched that are otherwise identical. A
p2p boolean tells drivers whether or not a given
interface will be used for p2p or not.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an interface is brought up, the recent changes
to allow changing type-while-up only set the running
bit after everything was done. This broke a number
of things, including idle calculation for monitor
interfaces, and it also broke WDS station insertion
(although nobody noticed yet).
Thus, change the code to set the running bit earlier,
but keep it after the driver's add_interface was
called because otherwise drivers may iterate over
interfaces they haven't fully set up yet.
Reported-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support to mac80211 for changing the interface
type even when the interface is UP, if the driver
supports it.
To achieve this
* add a new driver callback for switching,
* split some of the interface up/down code out
into new functions (do_open/do_stop), and
* maintain an own __SDATA_RUNNING bit that will
not be set during interface type, so that any
other code doesn't use the interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split the concurrent virtual interface checks
into a new function that can be used to check
for any given new interface type.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The libertas_tf special code for zero addresses
is a bit too complex, it compares against a stack
value instead of using is_zero_ether_addr() and
tries to update all interfaces even if just the
one that's being brought up needs to be changed.
Additionally, the repeated check for a valid MAC
address need only be done if we actually changed
it on the fly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a lot of redundant code in mac80211's
interface cleanup/down, for example freeing
AP beacons is done both when the interface is
set DOWN as well as when it is torn down, of
which only the former has any effect.
Also, a bunch of things should be closer to
where they matter, like the MLME timers that
we should cancel when disassociating, rather
than only when the interface is set DOWN.
Clean up all this code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some vendor specified mechanisms for 802.1X-style
functionality use a different protocol than EAP
(even if EAP is vendor-extensible). Support this
in mac80211 via the cfg80211 API for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Standardize logging messages from
printk(KERN_<level> "%s: " fmt , wiphy_name(foo), args);
to
wiphy_<level>(foo, fmt, args);
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to register for more than just
action frames by giving the frame subtype, and
make it possible to use this in various modes
as well.
With some tweaks and some added functionality
this will, in the future, also be usable in AP
mode and be able to replace the cooked monitor
interface currently used in that case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes we don't just need to know whether or
not the device is idle, but also per interface.
This adds that reporting capability to mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implement basic infrastructure to support use of NAPI by
mac80211-based hardware drivers.
Because mac80211 devices can support multiple netdevs, a dummy netdev
is used for interfacing with the NAPI code in the core of the network
stack. That structure is hidden from the hardware drivers, but the
actual napi_struct is exposed in the ieee80211_hw structure so that the
poll routines in drivers can retrieve that structure. Hardware drivers
can also specify their own weight value for NAPI polling.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a station interface is reused as monitor interface it is possible that
the carrier is still set to off. This breaks packet injection on that
monitor interface.
Force the carrier on in monitor interface initialisation like it is also done
for other interface types (e.g. adhoc, mesh point, ap).
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When aggregation related action frames are enqueued for further work,
and they originate from a STA that is part of an AP VLAN, they are
currently enqueued for the AP interface. This breaks the sta_info_get()
lookup in the actual work function, and because of that, aggregation
sessions are not established for this STA.
Fix this by replacing the sta_info_get call with a call to
sta_info_get_bss.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a circular locking dependency when configuring the
hardware ARP filters on association, occurring when flushing the mac80211
workqueue. This is what happens:
[ 92.026800] =======================================================
[ 92.030507] [ INFO: possible circular locking dependency detected ]
[ 92.030507] 2.6.34-04781-g2b2c009 #85
[ 92.030507] -------------------------------------------------------
[ 92.030507] modprobe/5225 is trying to acquire lock:
[ 92.030507] ((wiphy_name(local->hw.wiphy))){+.+.+.}, at: [<ffffffff8105b5c0>] flush_workq
ueue+0x0/0xb0
[ 92.030507]
[ 92.030507] but task is already holding lock:
[ 92.030507] (rtnl_mutex){+.+.+.}, at: [<ffffffff812b9ce2>] rtnl_lock+0x12/0x20
[ 92.030507]
[ 92.030507] which lock already depends on the new lock.
[ 92.030507]
[ 92.030507]
[ 92.030507] the existing dependency chain (in reverse order) is:
[ 92.030507]
[ 92.030507] -> #2 (rtnl_mutex){+.+.+.}:
[ 92.030507] [<ffffffff810761fb>] lock_acquire+0xdb/0x110
[ 92.030507] [<ffffffff81341754>] mutex_lock_nested+0x44/0x300
[ 92.030507] [<ffffffff812b9ce2>] rtnl_lock+0x12/0x20
[ 92.030507] [<ffffffffa022d47c>] ieee80211_assoc_done+0x6c/0xe0 [mac80211]
[ 92.030507] [<ffffffffa022f2ad>] ieee80211_work_work+0x31d/0x1280 [mac80211]
[ 92.030507] -> #1 ((&local->work_work)){+.+.+.}:
[ 92.030507] [<ffffffff810761fb>] lock_acquire+0xdb/0x110
[ 92.030507] [<ffffffff8105a51a>] worker_thread+0x22a/0x370
[ 92.030507] [<ffffffff8105ecc6>] kthread+0x96/0xb0
[ 92.030507] [<ffffffff81003a94>] kernel_thread_helper+0x4/0x10
[ 92.030507]
[ 92.030507] -> #0 ((wiphy_name(local->hw.wiphy))){+.+.+.}:
[ 92.030507] [<ffffffff81075fdc>] __lock_acquire+0x1c0c/0x1d50
[ 92.030507] [<ffffffff810761fb>] lock_acquire+0xdb/0x110
[ 92.030507] [<ffffffff8105b60e>] flush_workqueue+0x4e/0xb0
[ 92.030507] [<ffffffffa023ff7b>] ieee80211_stop_device+0x2b/0xb0 [mac80211]
[ 92.030507] [<ffffffffa0231635>] ieee80211_stop+0x3e5/0x680 [mac80211]
The locking in this case is quite complex. Fix the problem by rewriting the
way the hardware ARP filter list is handled - i.e. make a copy of the address
list to the bss_conf struct, and provide that list to the hardware driver
when needed.
The current patch will enable filtering also in promiscuous mode. This may need
to be changed in the future.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To prepare for allowing drivers to sleep in
ampdu_action, change the locking in the RX
aggregation code to use a mutex, so that it
would already allow drivers to sleep. But
explicitly disable BHs around the callback
for now since the TX part cannot yet sleep,
and drivers' locking might require it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This moves the aggregation callback processing
to the per-sdata skb queue and a work function
rather than the tasklet.
Unfortunately, this means that it extends the
pkt_type hack to that skb queue. However, it
will enable making ampdu_action API changes
gradually, my current plan is to get rid of
this again by forcing drivers to only return
from ampdu_action() when everything is done,
thus removing the callbacks completely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a corner case where we receive a fragmented
frame during a blockack session, in which case we
will terminate that session. To simplify future work
in this area that will culminate in allowing the
driver callbacks for aggregation to sleep, move the
processing of this case out of the RX path into the
interface work.
This will simplify future work because the new place
for this code doesn't require that the function will
always be atomic, which the RX path needs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To prepare for making the ampdu_action callback
sleep, make mac80211 always process blockack
action frames from the skb queue. This gets rid
of the current special case for managed mode
interfaces as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All the management processing functions free the
skb after they are done, so this can be done in
the new common code instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even with the previous patch, IBSS, managed
and mesh modes all attach their own work
function to the shared work struct, which
means some duplicated code. Change that to
only have a frame processing function and a
further work function for each of them and
share some common code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IBSS, managed and mesh modes all have their
own work struct, and in the future we want
to also use it in other modes to process
frames from the now common skb queue.
This also makes the skb queue and work safe
to use from other interface types.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IBSS, managed and mesh modes all have an
skb queue, and in the future we want to
also use it in other modes, so make them
all use a common skb queue already.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A number of places use RCU locking for accessing
the station list, even though they do not need
to. Use mutex locking instead to prepare for the
locking changes I want to make. The mlme code is
also using a WLAN_STA_DISASSOC flag that has the
same meaning as WLAN_STA_BLOCK_BA, so use that.
While doing so, combine places where we loop
over stations twice, and optimise away some of
the loops by checking if the hardware supports
aggregation at all first.
Also fix a more theoretical race condition: right
now we could resume, set up an aggregation session,
and right after tear it down again due to the code
that is needed for hardware reconfiguration here.
Also mark add a comment to that code marking it as
a workaround.
Finally, remove a pointless aggregation disabling
loop when an interface is stopped, directly after
that we remove all stations from it which will also
disable all aggregation sessions that may still be
active, and does so in a race-free way unlike the
current loop that doesn't block new sessions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since I recently made station management able
to sleep, I can now rework key management as
well; since it will no longer need a spinlock
and can also use a mutex instead, a bunch of
code to allow drivers' set_key to sleep while
key management is protected by a spinlock can
now be removed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ever since we use only cfg80211 for configuration,
there is no configuration that could be pending at
this point, cfg80211 will have the configuration
that is pending and apply it afterwards.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
This patch is based on a RFC patch by Kalle Valo.
The wl1271 has a feature which handles the connection monitor logic
in hardware, basically sending periodically nullfunc frames and reporting
to the host if AP is lost, after attempting to recover by sending
probe-requests to the AP.
Add support to mac80211 by adding a new flag IEEE80211_HW_CONNECTION_MONITOR
which prevents conn_mon_timer from triggering during idle periods, and
prevents sending probe-requests to the AP if beacon-loss is indicated by the
hardware.
Cc: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers can now advertise to cfg80211 that they have
multiple MAC addresses reserved for a device, but we
don't currently make use of that in mac80211.
Change that and assign different addresses to new
virtual interfaces (if addresses are available) in
order to make it easier for users to use multiple
virtual interfaces; they no longer need to always
assign a new MAC address manually.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a copy bug introduced by
commit 47846c9b0c
Author: Johannes Berg <johannes@sipsolutions.net>
Date: Wed Nov 25 17:46:19 2009 +0100
mac80211: reduce reliance on netdev
This manifested itself only in debug messages
and in the debugfs rename failure that would
always happen due to trying to rename the dir
over itself.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The WMM AC selection added to the monitor mode selection function
accidentally assigns non-QoS data frames to the same AC as mgmt frames
(VO). This is not serious, but should be fixed anyway. This patch
assigns them to the BE AC instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend struct cfg80211_bitrate_mask to actually use a bitfield mask
instead of just a single fixed or maximum rate index. This change
itself does not modify the behavior (except for debugfs files), but it
prepares cfg80211 and mac80211 for a new nl80211 command for setting
which rates can be used in TX rate control.
Since frames are now going through the rate control algorithm
unconditionally, the internal IEEE80211_TX_INTFL_RCALGO flag can now
be removed. The RC implementations can use the rate_idx_mask value to
optimize their behavior if only a single rate is enabled.
The old max_rate_idx in struct ieee80211_tx_rate_control is maintained
(but commented as deprecated) for backwards compatibility with existing
RC implementations. Once these implementations have been updated to
use the more generic rate_idx_mask, the max_rate_idx value can be
removed.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ieee80211_monitor_select_queue encounters data frames, it selects
the WMM AC based on skb->priority and assumes that skb->priority
contains a valid 802.1d tag. However this assumption is incorrect, since
ieee80211_select_queue has not been called at this point.
If skb->priority > 7, an array overrun occurs, which could lead to
invalid values, resulting in crashes in the tx path.
Fix this by setting skb->priority based on the 802.11 header for QoS
frames and using the default AC for all non-QoS frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I forgot to convert the radiotap length to
CPU endian, which sparse found thankfully.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bob Copeland